Scribd Logo
Upload

Welcome to Scribd!

  • 22 views

    Lab Experiment 4

    Uploaded by

    Tasnia Yasmin
    The document describes an experiment to design and set up a non-inverting amplifier circuit using an op-amp IC 741C with a gain of 11. It lists the objectives, equipment, principle of operation, and procedure which involves giving a 1Vpp 1kHz sine wave input and measuring the output voltage and gain. The expected output is an amplified waveform in phase with the input.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Lab Experiment 4

    Uploaded by

    Tasnia Yasmin
    22 views2 pages
    The document describes an experiment to design and set up a non-inverting amplifier circuit using an op-amp IC 741C with a gain of 11. It lists the objectives, equipment, principle of operation, and procedure which involves giving a 1Vpp 1kHz sine wave input and measuring the output voltage and gain. The expected output is an amplified waveform in phase with the input.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes an experiment to design and set up a non-inverting amplifier circuit using an op-amp IC 741C with a gain of 11. It lists the objectives, equipment, principle of operation, and procedure which involves giving a 1Vpp 1kHz sine wave input and measuring the output voltage and gain. The expected output is an amplified waveform in phase with the input.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    22 views2 pages

    Lab Experiment 4

    Uploaded by

    Tasnia Yasmin
    The document describes an experiment to design and set up a non-inverting amplifier circuit using an op-amp IC 741C with a gain of 11. It lists the objectives, equipment, principle of operation, and procedure which involves giving a 1Vpp 1kHz sine wave input and measuring the output voltage and gain. The expected output is an amplified waveform in phase with the input.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    EEE 204

    Experiment No 4
    NON- INVERTING AMPLIFIER
    Aim: To design and setup a non-inverting amplifier circuit with OPAMP IC 741C for a gain
    of 11, plot the waveform, observe the phase reversal, measure the gain.
    Objectives: After completion of this experiment, student will be able to design and setup a
    non-inverting amplifier using OP AMP. He/she will acquire skill to design and implement
    OPAMP non-inverting amplifier circuit.
    Equipments/Components:
    Sl .No Name and Specification Quantity required
    1 Dual power supply +/- 15V 1
    2 Function generator (0 - 1MHz ) 1
    3 Oscilloscope 1
    4 Bread board 1
    5 IC 741C 1
    6 Resistors 2
    7 Probes and connecting wires As required.

    Principle:

    It is a linear closed loop mode application of op-amp and employs negative feedback.
    The Rf and Ri are the feedback and input resistance of the circuit respectively. There will be
    no phase difference between the output and input. Hence it is called non-inverting amplifier.

    Av = Vo / Vin = 1+ Rf/ Ri ,

    Here the +Ve sign indicates that the output will be an amplified wave in phase with
    the input. By varying the Rf or Ri, the gain of the amplifier can be varied to any desired value.

    Procedure

    1. Check the components.


    2. Setup the circuit on the breadboard and check the connections.
    3. Switch on the power supply.
    4. Give 1 Vpp / 1 KHz sine wave as input.
    5. Observe input and output on the two channels of the CRO simultaneously.
    6. Note down and draw the input and output waveforms on the graph.
    7. Verify the input and output waveforms are in phase.
    8. Verify the obtained gain is same as designed value.
    EEE 204

    Result:

    Circuit Diagram

    Design:

    Gain of an inverting amplifier Av=Vo/Vin = 1+Rf/ Ri,


    Let the required gain be 11,
    Therefore Av= 1+Rf/ Ri= 11
    Rf/ Ri = 10
    Take Ri= 1KΩ, Then Rf = 10KΩ

    Observations: Vin = 1Vpp Vo = ?


    Gain Av = Vo/Vin =?
    Observed phase difference between the input and the output on the CRO =?

    Graph:

    Discussion:

    You might also like