UM1658

User manual
Discovery kit for STM32F030 Value Line microcontrollers

Introduction
The STM32F030 Value Line Discovery kit (32F0308DISCOVERY) helps you to discover the
device features and to develop your applications easily. It is based on STM32F030R8T6, an
STM32 F0 series 32-bit ARM® Cortex™-M0 microcontroller, and includes an ST-LINK/V2
embedded debug tool, LEDs, push buttons and a prototyping board.

Figure 1. 32F0308DISCOVERY

September 2013 DocID025097 Rev 1 1/39

www.st.com
Contents UM1658

Contents

1 Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Quick start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Development toolchains supporting the 32F0308DISCOVERY . . . . . . . . . 6
2.4 Order code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4 Hardware and layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4.1 STM32F030R8T6 microcontroller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.2 Embedded ST-LINK/V2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.2.1 Using ST-LINK/V2 to program/debug the STM32 F0 on board . . . . . . . 14
4.2.2 Using ST-LINK/V2 to program/debug an external STM32 application . . 15
4.3 Power supply and power selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.4 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.5 Push buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.6 JP2 (Idd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
4.7 OSC clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.7.1 OSC clock supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.7.2 OSC 32 KHz clock supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
4.8 Solder bridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.9 Extension connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

5 Connecting modules on the prototyping board . . . . . . . . . . . . . . . . . . 25

5.1 Mikroelektronica accessory boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
5.2 ST MEMS “adapter boards”, standard DIL24 socket . . . . . . . . . . . . . . . . 28
5.3 Arduino shield boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6 Mechanical drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

7 Electrical schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

2/39 DocID025097 Rev 1

UM1658 List of tables

List of tables

Table 1. ON/OFF conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table 2. Jumper states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Table 3. Debug connector CN3 (SWD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 4. Solder bridge settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Table 5. MCU pin description versus board function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Table 6. Connecting using mikroBUS™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 7. Connecting using IDC10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 8. Connecting with a DIL24 board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 9. Supported MEMS adapter boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Table 10. Connecting with Arduino shields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 11. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

DocID025097 Rev 1 3/39

3
List of figures UM1658

List of figures

Figure 1. 32F0308DISCOVERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 2. Hardware block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 3. Top layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 4. Bottom layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 5. STM32F030R8T6 package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 6. STM32F030R8T6 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 7. Typical configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 8. 32F0308DISCOVERY connections image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 9. ST-LINK connections image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 10. Using IDC10 and mikroBUS™ connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 11. DIL24 socket connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 12. Arduino shield board connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 13. 32F0308DISCOVERY mechanical drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Figure 14. 32F0308DISCOVERY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 15. ST-LINK/V2 (SWD only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Figure 16. MCU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

4/39 DocID025097 Rev 1

UM1658 Conventions

1 Conventions

Table 1 provides the definition of some conventions used in the present document.

Table 1. ON/OFF conventions

Convention Definition

Jumper JP1 ON Jumper fitted

Jumper JP1 OFF Jumper not fitted
Solder bridge SBx ON SBx connections closed by solder
Solder bridge SBx OFF SBx connections left open

DocID025097 Rev 1 5/39

38
Quick start UM1658

2 Quick start

The STM32F030 Value Line Discovery kit is a low-cost and easy-to-use development kit to
quickly evaluate and start development with an STM32 F0 series microcontroller.
Before installing and using the product, please accept the Evaluation Product License
Agreement from www.st.com/stm32f0-discovery.
For more information on the STM32F030 Value Line Discovery kit and for demonstration
software, visit www.st.com/stm32f0-discovery.

2.1 Getting started

Follow the sequence below to configure the STM32F030 Value Line Discovery kit and
launch the DISCOVER application:
1. Check jumper position on the board, JP2 on, CN2 on (Discovery selected).
2. Connect the 32F0308DISCOVERY board to a PC with a USB cable ‘type A to mini-B’
through USB connector CN1 to power the board. Red LED LD1 (PWR) and LD2 (COM)
light up and green LED LD3 blinks.
3. Press user button B1 (bottom left corner of the board).
4. Observe how the green LED LD3 blinking changes according to USER button B1
clicks.
5. Each click on USER button B1 is confirmed by the blue LED LD4.
6. To study or modify the DISCOVER project related to this demo, visit
www.st.com/stm32f0-discovery and follow the tutorial.
7. Discover the STM32F0 features, download and execute programs proposed in the list
of projects.
8. Develop your own application using available examples.

2.2 System requirements

• Windows PC (XP, Vista, 7)
• USB type A to Mini-B USB cable

2.3 Development toolchains supporting the 32F0308DISCOVERY

• Altium®, TASKING™ VX-toolset
• ARM®, Atollic TrueSTUDIO®
• IAR™, EWARM (IAR Embedded Workbench®)
• Keil™, MDK-ARM™

2.4 Order code

To order the STM32F030 Value Line Discovery kit, use the order code
STM32F0308-DISCO.

6/39 DocID025097 Rev 1

UM1658 Features

3 Features

The STM32F030 Value Line Discovery kit offers the following features:
• STM32F030R8T6 microcontroller featuring 64 KB Flash, 8 KB RAM in an LQFP64
package
• On-board ST-LINK/V2 with selection mode switch to use the kit as a standalone
ST-LINK/V2 (with SWD connector for programming and debugging)
• Board power supply: through USB bus or from an external 5 V supply voltage
• External application power supply: 3 V and 5 V
• Four LEDs:
– LD1 (red) for 3.3 V power on
– LD2 (red/green) for USB communication
– LD3 (green) for PC9 output
– LD4 (blue) for PC8 output
• Two push buttons (user and reset)
• Extension header for LQFP64 I/Os for quick connection to prototyping board and easy
probing.
• An additional board is provided with the kit which can be connected to the extension
connector for even easier prototyping and probing.
• A large number of free ready-to-run application firmware examples are available on
www.st.com/stm32f0-discovery to support quick evaluation and development.

DocID025097 Rev 1 7/39

38
Hardware and layout UM1658

4 Hardware and layout

The STM32F030 Value Line Discovery board is designed around the STM32F030R8T6
microcontroller in a 64-pin LQFP package.
Figure 2 illustrates the connections between the STM32F030R8T6 and its peripherals
(ST-LINK/V2, push button, LEDs and connectors).
Figure 3 and Figure 4 help you to locate these features on the STM32F030 Value Line
Discovery board.

Figure 2. Hardware block diagram

Mini
USB

Embedded
ST-LINK/V2
SWD

STM32F030R8T6

I/O I/O
Header

Header
I/O RESET

LED B2
LD3, PC9 RST
LED B1
LD4, PC8 USER

MSv31935V1

8/39 DocID025097 Rev 1

UM1658 Hardware and layout

Figure 3. Top layout

(red/green LED) LD2 ST-LINK/V2 LD1 (red LED)

COM PWR
5V power supply
3V power supply
input output
input output
CN3 CN2
SWD connector ST-LINK/DISCOVERY
selector

JP2
IDD measurement

SB1 (VDD)

SB3 (B1-USER)

B2 reset button
STM32F030R8T6
SB4 (B2-RESET)
B1 user button

(green LED) LD3

LD4 (blue LED)
MB1134 revA
STM32F0308-DISCO
MS31936V1

Note: Pin 1 of CN2, CN3, P1 and P2 connectors are identified by a square.

DocID025097 Rev 1 9/39

38
Hardware and layout UM1658

Figure 4. Bottom layout

SB5, SB7, SB9, SB11

(RESERVED)

SB6, SB8, SB10, SB12

(DEFAULT)

SB13 (STM_RST)

SB14, SB15 (RX, TX)

SB16, SB17 (X2 crystal)

SB18 (MCO)
SB19 (NRST)
SB20, SB21 (X3 crystal)

SB22 (T_SWO)

MS30025V1

10/39 DocID025097 Rev 1

UM1658 Hardware and layout

4.1 STM32F030R8T6 microcontroller

The STM32F030R8T6 microcontroller incorporates the high-performance ARM
Cortex™-M0 32-bit RISC core operating at a 48 MHz frequency, high-speed embedded
memories (up to 64 Kbytes of Flash memory and up to 8 Kbytes of SRAM), and an
extensive range of enhanced peripherals and I/Os. All devices offer standard
communication interfaces (up to two I2Cs, up to two SPIs, and up to two USARTs), one
12-bit ADC, up to 6 general-purpose 16-bit timers and an advanced-control PWM timer.

Figure 5. STM32F030R8T6 package

STM32F030R8T6

64 Kbyte of Flash memory

8 Kbytes of SRAM

LQFP64 10 x 10 mm MS31938V1

The STM32F030R8T6 microcontroller operates in the -40 to +85 °C temperature range,

from a 2.4 V to 3.6 V power supply. A comprehensive set of power-saving modes allows the
design of low-power applications.
These features make the STM32F030R8T6 microcontroller suitable for a wide range of
applications such as application control and user interfaces, handheld equipment,
A/V receivers and digital TV, PC peripherals, gaming platforms, e-bikes, consumer
appliances, printers, scanners, alarm systems, video intercoms, and HVACs.

DocID025097 Rev 1 11/39

38
Hardware and layout UM1658

Figure 6. STM32F030R8T6 block diagram

Serial VDD18 POWER

SWCLK Wire VOLT.REG
SWDIO VDD = 2.4 to 3.6 V
Debug

Obl
3.3 V TO 1.8 V VSS
as AF Flash

interface
up to @ VDD

Flash
64 KB,
CORTEX-M0 CPU POR SUPPLY
32 bits
fHCLK = 48 MHz Reset SUPERVISION
Int NRST

Bus matrix

controller
SRAM POR/PDR VDDA

SRAM
@ VDDA VDD
4 / 8 KB
NVIC RC HS 14 MHz
RC HS 8 MHz
@ VDDA
GP DMA
RC LS @ VDD
5 channels OSC_IN (PF0)
XTAL OSC
PLL OSC_OUT (PF1)
4-32 MHz
IWDG
Power
AHBPCLK Controller
RESET & APBPCLK
ADCCLK @ VDD
CLOCK
USARTCLK OSC32_IN (PC14)
CONTROL HCLK
XTAL32 kHz
PA[15:0] GPIO port A OSC32_OUT (PC15)
FCLK

GPIO port B RTC TAMPER-RTC

PB[15:0]
AHB decoder

(ALARM OUT)
GPIO port C RTC interface
PC[15:0] CRC

PD2 GPIO port D

PF[1:0] GPIO port F 4 channels

PF[7:4] TIMER 1 3 compl. channels
BRK, ETR input as AF
TIMER 3 4 ch., ETR as AF

AHB TIMER 14 1 channel as AF

APB 2 channels
TIMER 15 1 compl, BRK as AF

EXT. IT 1 channel
55 AF TIMER 16 1 compl, BRK as AF
WKUP
WWDG 1 channel
MOSI, TIMER 17
1 compl, BRK as AF
MISO,
SPI1 IR_OUT as AF
SCK, DBGMCU
NSS as AF
USART1 RX, TX,CTS, RTS,
MOSI/MISO, CK as AF
SPI2
SCK/NSS, USART2 RX, TX,CTS, RTS,
as AF CK as AF
SYSCFG IF

SCL, SDA, SMBA

I2C 1
(20 mA for FM+) as AF
@ VDDA
Temp. SCL, SDA
I2C2
sensor as AF
16 12-bit
AD inputs IF
ADC1
TIMER 6
VDDA
VSSA

MSv32137V1

12/39 DocID025097 Rev 1

UM1658 Hardware and layout

4.2 Embedded ST-LINK/V2

The ST-LINK/V2 programming and debugging tool is integrated on the
32F0308DISCOVERY. The embedded ST-LINK/V2 can be used in 2 different ways
according to the jumper states (see Table 2):
• Program/debug the MCU on board,
• Program/debug an MCU in an external application board using a cable connected to
SWD connector CN3.
The embedded ST-LINK/V2 supports only SWD for STM32 devices. For information about
debugging and programming features refer to user manual UM1075 (ST-LINK/V2 in-circuit
debugger/programmer for STM8 and STM32) which describes in detail all the ST-LINK/V2
features.

Figure 7. Typical configuration

Hardware requirements:
- USB cable type A to mini-B
- computer with Windows XP, Vista or 7

Development toolchain:
Altium, TASKING VX-Toolset,
Atollic, TrueSTUDIO
IAR, EWARM
Keil, MDK-ARM

MS19052V2

Table 2. Jumper states

Jumper state Description

Both CN2 jumpers ON ST-LINK/V2 functions enabled for on board programming (default)
ST-LINK/V2 functions enabled for application through external CN3
Both CN2 jumpers OFF
connector (SWD supported)

DocID025097 Rev 1 13/39

38
Hardware and layout UM1658

4.2.1 Using ST-LINK/V2 to program/debug the STM32 F0 on board

To program the STM32 F0 on board, simply plug in the two jumpers on CN2, as shown in
Figure 8 in red, but do not use the CN3 connector as that could disturb communication with
the STM32F030R8T6 of the 32F0308DISCOVERY.

Figure 8. 32F0308DISCOVERY connections image

CN3
SWD connector

CN2 jumpers on

14/39 DocID025097 Rev 1

UM1658 Hardware and layout

4.2.2 Using ST-LINK/V2 to program/debug an external STM32 application

It is very easy to use the ST-LINK/V2 to program the STM32 on an external application.
Simply remove the 2 jumpers from CN2 as shown in Figure 9, and connect your application
to the CN3 debug connector according to Table 3.
Note: SB19 and SB22 must be OFF if you use CN3 pin 5 in your external application.

Table 3. Debug connector CN3 (SWD)

Pin CN3 Designation

1 VDD_TARGET VDD from application

2 SWCLK SWD clock
3 GND Ground
4 SWDIO SWD data input/output
5 NRST RESET of target MCU
6 SWO Reserved

Figure 9. ST-LINK connections image

CN3
SWD connector

CN2 ju
jumpers
umpers off

DocID025097 Rev 1 15/39

38
Hardware and layout UM1658

4.3 Power supply and power selection

The power supply is provided either by the host PC through the USB cable, or by an
external 5 V power supply.
The D1 and D2 diodes protect the 5 V and 3 V pins from external power supplies:
• 5 V and 3 V can be used as output power supplies when another application board is
connected to pins P1 and P2.
In this case, the 5 V and 3 V pins deliver a 5 V or 3 V power supply and power
consumption must be lower than 100 mA.
• 5 V can also be used as input power supplies; for example, when the USB connector is
not connected to the PC.
In this case, the 32F0308DISCOVERY board must be powered by a power supply unit
or by auxiliary equipment complying with standard EN-60950-1: 2006+A11/2009, and
must be Safety Extra Low Voltage (SELV) with limited power capability.

4.4 LEDs
• LD1 PWR: Red LED indicates that the board is powered.
• LD2 COM: Tricolor LED (COM) advises on the communication status as follows:
– Slow blinking Red LED/Off: At power on before USB initialization
– Fast blinking Red LED/Off: After the first correct communication between PC and
STLINK/V2 (enumeration)
– Red LED On: When initialization between PC and ST-LINK/V2 is successfully
finished
– Green LED On: After successful target communication initialization
– Blinking Red/Green LED: During communication with target
– Red LED On: Communication finished and OK
– Orange LED On: Communication failure
• User LD3: Green user LED connected to the I/O PC9 of the STM32F030R8T6.
• User LD4: Blue user LED connected to the I/O PC8 of the STM32F030R8T6.

4.5 Push buttons

• B1 USER: User push button connected to the I/O PA0 of the STM32F030R8T6.
• B2 RESET: Push button used to RESET the STM32F030R8T6.

4.6 JP2 (Idd)

Jumper JP2, labeled Idd, allows the consumption of STM32F030R8T6 to be measured by
removing the jumper and connecting an ammeter.
• Jumper on: STM32F030R8T6 is powered (default).
• Jumper off: an ammeter must be connected to measure the STM32F030R8T6 current,
(if there is no ammeter, the STM32F030R8T6 is not powered).

16/39 DocID025097 Rev 1

UM1658 Hardware and layout

4.7 OSC clock

4.7.1 OSC clock supply

PF0 and PF1 can be used as GPIO or as HSE oscillator. By default these I/Os are
configured as GPIO, so SB16 and SB17 are closed, SB18 is open and R22, R23, C13 and
C14 are not populated.
An external HSE clock can be provided to the MCU in three ways:
• MCO from ST-LINK. From MCO of the STM32F103. This frequency cannot be
changed, it is fixed at 8 MHz and connected to PF0-OSC_IN of the STM32F030R8T6.
Configuration needed:
– SB16, SB18 CLOSED
– R22, R23 removed
– SB17 OPEN
• Oscillator onboard. From X2 crystal (not provided). For typical frequencies and its
capacitors and resistors, please refer to the STM32F030R8T6 datasheet.
Configuration needed:
– SB16, SB17, SB18 OPEN
– R22, R23, C13, C14 soldered
• Oscillator from external PF0. From external oscillator through pin 7 of the P1
connector. Configuration needed:
– SB16, SB17 CLOSED
– SB18 OPEN
– R22 and R23 removed

4.7.2 OSC 32 KHz clock supply

PC14 and PC15 can be used as GPIO or as LSE oscillator. By default these I/Os are
configured as GPIO, so SB20 & SB21 are closed and X3, R24, R25 are not populated.
An external LSE clock can be provided to the MCU in two ways:
• Oscillator onboard. From X3 crystal (not provided). Configuration needed:
– SB20, SB21 OPEN
– C15, C16, R24 and R25 soldered.
• Oscillator from external PC14. From external oscillator trough the pin 5 of P1
connector. Configuration needed:
– SB20, SB21 CLOSED
– R24 and R25 removed

DocID025097 Rev 1 17/39

38
Hardware and layout UM1658

4.8 Solder bridges

Table 4. Solder bridge settings
Bridge State(1) Description

X2, C13, C14, R22 and R23 provide a clock. PF0, PF1 are disconnected
SB16,17 OFF
from P1.
(X2 crystal)(2)
ON PF0, PF1 are connected to P1 (R22, R23 and SB18 must not be fitted).
SB6,8,10,12 (Default) ON Reserved, do not modify.
SB5,7,9,11 (Reserved) OFF Reserved, do not modify.
X3, C15, C16, R24 and R25 deliver a 32 KHz clock. PC14, PC15 are not
SB20,21 OFF
connected to P1.
(X3 crystal)
ON PC14, PC15 are only connected to P1 (R24, R25 must not be fitted).
B2 push button is connected to the NRST pin of the STM32F030R8T6
ON
SB4 MCU.
(B2-RESET) B2 push button is not connected the NRST pin of the STM32F030R8T6
OFF
MCU.

SB3 ON B1 push button is connected to PA0.

(B1-USER) OFF B1 push button is not connected to PA0.

SB1 ON VDD_3 must be permanently connected to VDD for normal use.

(VDD_3) OFF Reserved, do not modify.

SB14,15 OFF Reserved, do not modify.

(RX,TX) ON Reserved, do not modify.
NRST signal of the CN3 connector is connected to the NRST pin of the
ON
SB19 STM32F030R8T6 MCU.
(NRST) NRST signal of the CN3 connector is not connected to the NRST pin of the
OFF
STM32F030R8T6 MCU.

SB22 ON SWO signal of the CN3 connector is connected to PB3.

(T_SWO) OFF SWO signal is not connected.

SB13 OFF No incidence on STM32F103C8T6 (ST-LINK/V2) NRST signal.

(STM_RST) ON STM32F103C8T6 (ST-LINK/V2) NRST signal is connected to GND.
BOOT0 signal of the STM32F030R8T6 MCU is held low through a
ON
SB2 510 Ohm pull-down resistor.
(BOOT0) BOOT0 signal of the STM32F030R8T6 MCU can be set high through a
OFF
10 KOhm pull-up resistor R27 to solder.

SB18 ON Provides the 8 MHz for OSC_IN from MCO of STM32F030R8T6.

(MCO)(2) OFF See SB16, SB17 description.
1. Default SBx state is shown in bold.
2. OSC_IN clock comes from MCO if SB18 is ON and SB16,17 are OFF
and comes from X2 if SB18 is OFF and SB16,17 are ON.

18/39 DocID025097 Rev 1

UM1658 Hardware and layout

4.9 Extension connectors

The male headers P1 and P2 can connect the 32F0308DISCOVERY to a standard
prototyping/wrapping board. STM32F030R8T6 GPI/Os are available on these connectors.
P1 and P2 can also be probed by an oscilloscope, logical analyzer or voltmeter.

Table 5. MCU pin description versus board function

MCU pin Board function

Power supply
Push button
LQFP64

Free I/O
Main Alternate

SWD

OSC
LED

CN3

P1

P2
function functions

BOOT0 BOOT0 60 6
RESET

NRST
NRST NRST 7 5 10

USART1_CTS,
USART2_CTS,
USER

PA0 ADC_IN0, 14 15
RTC_TAMP2,
WKUP1
USART1_RTS,
USART2_RTS,
PA1 15 16
EVENTOUT,
ADC_IN1
USART1_TX,
USART2_TX,
PA2 16 17
TIM15_CH1,
ADC_IN2
USART1_RX,
USART2_RX,
PA3 17 18
TIM15_CH2,
ADC_IN3
SPI1_NSS,
USART1_CK
PA4 USART2_CK, 20 21
TIM14_CH1,
ADC_IN4
SPI1_SCK,
PA5 21 22
ADC_IN5

DocID025097 Rev 1 19/39

38
Hardware and layout UM1658

Table 5. MCU pin description versus board function (continued)

MCU pin Board function

Power supply
Push button
LQFP64

Free I/O
Main Alternate

SWD

OSC
LED

CN3

P1

P2
function functions

SPI1_MISO,
TIM3_CH1,
TIM1_BKIN,
PA6 22 23
TIM16_CH1,
EVENTOUT,
ADC_IN6
SPI1_MOSI,
TIM3_CH2,
TIM14_CH1,
PA7 TIM1_CH1N, 23 24
TIM17_CH1,
EVENTOUT,
ADC_IN7
USART1_CK,
TIM1_CH1,
PA8 41 25
EVENTOUT,
MCO
USART1_TX,
TIM1_CH2,
PA9 42 24
TIM15_BKIN,
I2C1_SCL
USART1_RX,
TIM1_CH3,
PA10 43 23
TIM17_BKIN,
I2C1_SDA
USART1_CTS,
PA11 TIM1_CH4, 44 22
EVENTOUT
USART1_RTS,
PA12 TIM1_ETR, 45 21
EVENTOUT
SWDIO SWCLK

IR_OUT,
PA13 46 4 20
SWDIO

USART1_TX,
PA14 USART2_TX, 49 2 17
SWCLK

20/39 DocID025097 Rev 1

UM1658 Hardware and layout

Table 5. MCU pin description versus board function (continued)

MCU pin Board function

Power supply
Push button
LQFP64

Free I/O
Main Alternate

SWD

OSC
LED

CN3

P1

P2
function functions

SPI1_NSS,
USART1_RX,
PA15 50 16
USART2_RX,
EVENTOUT
TIM3_CH3,
PB0 TIM1_CH2N, 26 27
EVENTOUT
TIM3_CH4,
PB1 TIM14_CH1, 27 28
TIM1_CH3N
PB2 - 28 29
SPI1_SCK,
SWO

PB3 55 6 11
EVENTOUT
SPI1_MISO,
PB4 TIM3_CH1, 56 10
EVENTOUT
SPI1_MOSI,
I2C1_SMBA,
PB5 57 9
TIM16_BKIN,
TIM3_CH2
I2C1_SCL,
PB6 USART1_TX, 58 8
TIM16_CH1N
I2C1_SDA,
PB7 USART1_RX, 59 7
TIM17_CH1N
I2C1_SCL,
PB8 61 4
TIM16_CH1
I2C1_SDA,
IR_OUT,
PB9 62 3
TIM17_CH1,
EVENTOUT
I2C1_SCL,
PB10 29 30
I2C2_SCL

DocID025097 Rev 1 21/39

38
Hardware and layout UM1658

Table 5. MCU pin description versus board function (continued)

MCU pin Board function

Power supply
Push button
LQFP64

Free I/O
Main Alternate

SWD

OSC
LED

CN3

P1

P2
function functions

I2C1_SDA,
PB11 I2C2_SDA, 30 31
EVENTOUT
SPI1_NSS,
SPI2_NSS,
PB12 33 32
TIM1_BKIN,
EVENTOUT
SPI1_SCK,
PB13 SPI2_SCK, 34 32
TIM1_CH1N
SPI1_MISO,
SPI2_MISO,
PB14 35 31
TIM1_CH2N,
TIM15_CH1
SPI1_MOSI,
SPI2_MOSI,
PB15 TIM1_CH3N, 36 30
TIM15_CH1N,
TIM15_CH2
PC0 EVENTOUT ADC_IN10 8 11
PC1 EVENTOUT ADC_IN11 9 12
PC2 EVENTOUT ADC_IN12 10 13
PC3 EVENTOUT ADC_IN13 11 14
PC4 EVENTOUT ADC_IN14 24 25
PC5 ADC_IN15 25 26
PC6 TIM3_CH1 37 29
PC7 TIM3_CH2 38 28
BLUE GREEN

PC8 TIM3_CH3 39 27

PC9 TIM3_CH4 40 26

PC10 - 51 15

22/39 DocID025097 Rev 1

UM1658 Hardware and layout

Table 5. MCU pin description versus board function (continued)

MCU pin Board function

Power supply
Push button
LQFP64

Free I/O
Main Alternate

SWD

OSC
LED

CN3

P1

P2
function functions

PC11 - 52 14
PC12 - 53 13
RTC_TAMP1,
RTC_TS,
PC13 2 4
RTC_OUT,
WKUP2

OSC32_IN OSC32_OUT
PC14-
OSC32_ OSC32_IN 3 5
IN

PC15-
OSC32_ OSC32_OUT 4 6
OUT

PD2 TIM3_ETR 54 12
OSC_IN OSC_OUT

PF0-
OSC_IN 5 7
OSC_IN

PF1-
OSC_ OSC_OUT 6 8
OUT

PF4 EVENTOUT 18 19
PF5 EVENTOUT 19 20
I2C1_SCL,
PF6 47 19
I2C2_SCL
I2C1_SDA,
PF7 48 18
I2C2_SDA
VDD_3 VDD 1 3
VDD_1 64
VDD_2 32
VDDA 13

DocID025097 Rev 1 23/39

38
Hardware and layout UM1658

Table 5. MCU pin description versus board function (continued)

MCU pin Board function

Power supply
Push button
LQFP64

Free I/O
Main Alternate

SWD

OSC
LED

CN3

P1

P2
function functions

VSS_1 63
VSS_2 31
VSSA 12
5V 1
3V 1

VDD GND GND GND GND

5

2 2
GND

33 33

24/39 DocID025097 Rev 1

UM1658 Connecting modules on the prototyping board

5 Connecting modules on the prototyping board

This section gives some examples of how to connect ready-to-use modules available from
different manufacturers to the STM32F030 Value Line Discovery kit via the prototyping
board included in the kit.
Software examples, based on the connections described below, are available at
www.st.com/stm32f0-discovery.

5.1 Mikroelektronica accessory boards

Mikroelektronika, http://www.mikroe.com, has specified two standard connectors for their
accessory boards, named mikroBUS™ (http://www.mikroe.com/mikrobus_specs.pdf) and
IDC10.
MikroBUS™ is a 16-pin connector to connect accessory boards very quickly and easily to a
microcontroller board through SPI, USART or I2C communications, along with additional
pins such as Analog Input, PWM and Interrupt.
The set of mikroElektronika boards compatible with mikroBUS™ is called “Click boards”.
IDC10 is a 10-pin connector to connect the general purpose I/O of an MCU to other
accessory boards.
The tables below are one solution for connecting mikroBUS™ and IDC boards to the
32F0308DISCOVERY; this solution used in the different examples is available at
www.st.com/stm32f0-discovery.

Table 6. Connecting using mikroBUS™

Mikroelektronica mikroBUS™ 32F0308DISCOVERY

Pin Description Pin Description

AN Analog pin PA4 DAC1_OUT
RST Reset pin PB13 GPIO OUTPUT (5V tolerant)
CS SPI Chip Select line PA11 GPIO OUTPUT (5V tolerant)
SCK SPI Clock line PB3 SPI1_SCK
MISO SPI Slave Output line PB4 SPI1_MISO
MOSI SPI Slave Input line PB5 SPI1_MOSI
PWM PWM output line PA8 TIM1_CH1
INT Hardware Interrupt line PB12 GPIO INPUT EXTI (5V tolerant)
RX UART Receive line PA3 USART2_RX
TX UART Transmit line PA2 USART2_TX
SCL I2C Clock line PF6 I2C2_SCL
SDA I2C Data line PF7 I2C2_SDA
5V VCC 5V power line 5V Power line

DocID025097 Rev 1 25/39

38
Connecting modules on the prototyping board UM1658

Table 7. Connecting using IDC10

Mikroelektronica IDC10 connector 32F0308DISCOVERY

P0 GPIO PC0 GPIO OUTPUT (3.3V tolerant)

P1 GPIO PC1 GPIO OUTPUT (3.3V tolerant)
P2 GPIO PC2 GPIO OUTPUT (3.3V tolerant)
P3 GPIO PC3 GPIO OUTPUT (3.3V tolerant)
P4 GPIO PC4 GPIO OUTPUT (3.3V tolerant)
P5 GPIO PC5 GPIO OUTPUT (3.3V tolerant)
P6 GPIO PC6 GPIO OUTPUT (5V tolerant)
P7 GPIO PC7 GPIO OUTPUT (5V tolerant)
VCC VCC 5V power line 3V VDD
GND Reference Ground GND VSS
P0 GPIO PC0 GPIO OUTPUT (3.3V tolerant)
P1 GPIO PC1 GPIO OUTPUT (3.3V tolerant)
P2 GPIO PC2 GPIO OUTPUT (3.3V tolerant)
P3 GPIO PC3 GPIO OUTPUT (3.3V tolerant)

26/39 DocID025097 Rev 1

UM1658 Connecting modules on the prototyping board

The Figure 10 illustrates the connections between the 32F0308DISCOVERY and the 2
connectors, IDC10 and mikroBUS™.

Figure 10. Using IDC10 and mikroBUS™ connectors

DocID025097 Rev 1 27/39

38
Connecting modules on the prototyping board UM1658

5.2 ST MEMS “adapter boards”, standard DIL24 socket

STMicroelectronics has defined a standard DIL24 connector to easily evaluate its MEMS
sensors connected to a microcontroller through SPI or I2C communications.
Table 8 is one solution for connecting the DIL24 boards to the 32F0308DISCOVERY, this
solution is used in different examples and available at www.st.com/stm32f0-discovery.

Table 8. Connecting with a DIL24 board

ST MEMS DIL24 Eval board 32F0308DISCOVERY

P01 VDD Power supply 3V VDD

P02 Vdd_IO Power supply for I/O pins 3V VDD
P03 NC
P04 NC
P05 NC
P06 NC
P07 NC
P08 NC
P09 NC
P10 NC
P11 NC
P12 NC
P13 GND 0V supply GND GND
P14 INT1 Inertial interrupt 1 PB12 GPIO INPUT EXTI (5V tolerant)
P15 INT2 inertial interrupt 2 PB11 GPIO INPUT EXTI (5V tolerant)
P16 NC
P17 NC
P18 NC
P19 CS - 0:SPI enabled 1:I2C mode PA11 GPIO OUTPUT (5V tolerant)

SCL (I2C serial clock) PB6 I2C1_SCL

P20
SPC (SPI serial clock) PB3 SPI1_SCK

SDA I2C Serial Data PB7 I2C1_SDA

P21
SDI SPI Serial Data Input PB5 SPI1_MOSI

SDO SPI Serial Data Output

P22 PB4 SPI1_MISO
I2C less significant bit of the device address

P23 NC
P24 NC

28/39 DocID025097 Rev 1

UM1658 Connecting modules on the prototyping board

Figure 11 illustrates the connections between the 32F0308DISCOVERY and the DIL24
socket.

Figure 11. DIL24 socket connections

DocID025097 Rev 1 29/39

38
Connecting modules on the prototyping board UM1658

Supported MEMS adapter boards

Table 9 is a list of supported MEMS adapter boards as of April, 2012.

Table 9. Supported MEMS adapter boards

ST MEMS DIL24 Eval Board Core product

STEVAL-MKI009V1 LIS3LV02DL
STEVAL-MKI013V1 LIS302DL
STEVAL-MKI015V1 LIS344ALH
STEVAL-MKI082V1 LPY4150AL
STEVAL-MKI083V1 LPY450AL
STEVAL-MKI084V1 LPY430AL
STEVAL-MKI085V1 LPY410AL
STEVAL-MKI086V1 LPY403AL
STEVAL-MKI087V1 LIS331DL
STEVAL-MKI088V1 LIS33DE
STEVAL-MKI089V1 LIS331DLH
STEVAL-MKI090V1 LIS331DLF
STEVAL-MKI091V1 LIS331DLM
STEVAL-MKI092V1 LIS331HH
STEVAL-MKI095V1 LPR4150AL
STEVAL-MKI096V1 LPR450AL
STEVAL-MKI097V1 LPR430AL
STEVAL-MKI098V1 LPR410AL
STEVAL-MKI099V1 LPR403AL
STEVAL-MKI105V1 LIS3DH
STEVAL-MKI106V1 LSM303DLHC
STEVAL-MKI107V1 L3G4200D
STEVAL-MKI107V2 L3GD20
STEVAL-MKI108V1 9AXISMODULE v1 [LSM303DLHC + L3G4200D]
STEVAL-MKI108V2 9AXISMODULE v2 [LSM303DLHC + L3GD20]
STEVAL-MKI110V1 AIS328DQ
STEVAL-MKI113V1 LSM303DLM
STEVAL-MKI114V1 MAG PROBE (based on LSM303DLHC)
STEVAL-MKI120V1 LPS331AP
STEVAL-MKI122V1 LSM330DLC
STEVAL-MKI123V1 LSM330D

30/39 DocID025097 Rev 1

UM1658 Connecting modules on the prototyping board

Table 9. Supported MEMS adapter boards (continued)

ST MEMS DIL24 Eval Board Core product

10AXISMODULE [LSM303DLHC + L3GD20+

STEVAL-MKI124V1
LPS331AP]
STEVAL-MKI125V1 A3G4250D

Note: For an up-to-date list, visit http://www.st.com/internet/evalboard/subclass/1116.jsp. The

DIL24 boards are described as “adapter boards” in the field “General Description”.

5.3 Arduino shield boards

Arduino™ is an open-source electronics prototyping platform based on flexible, easy-to-use
hardware and software. See http://www.arduino.cc for more information.
Arduino accessory boards are called “Shields” and can be easily connected to the
32F0308DISCOVERY according to the following table.

Table 10. Connecting with Arduino shields

Arduino power connector 32F0308DISCOVERY

Reset Reset from Shield board NRST Reset discovery

3V3 VCC 3.3V power line 3V VDD
5V VCC 5V power line 5V VDD
GND Reference Ground GND Reference Ground
GND Reference Ground GND Reference Ground
Jumper fitted to power board by
Vin External alimentation 3V
External 3 V power supply.

Arduino analog in connector 32F0308DISCOVERY

A0 Analog input or Digital pin 14 PC0 ADC_IN10

A1 Analog input or Digital pin 15 PC1 ADC_IN11
A2 Analog input or Digital pin 16 PC2 ADC_IN12
A3 Analog input or Digital pin 17 PC3 ADC_IN13
Analog input or SDA or Digital
A4 PC4 or PF7 ADC_IN14 or I2C2_SDA
pin 18
Analog input or SCL or Digital
A5 PC5 or PF6 ADC_IN15 or I2C2_SCL
pin 19

DocID025097 Rev 1 31/39

38
Connecting modules on the prototyping board UM1658

Table 10. Connecting with Arduino shields (continued)

Arduino digital connector 32F0308DISCOVERY

D0 Digital pin 0 or RX PA3 USART2_RX

D1 Digital pin 1 or TX PA2 USART2_TX
D2 Digital pin 2 / External interrupt PB12 EXTI (5V tolerant)
D3 Digital pin 3 / Ext int or PWM PB11 EXTI (5V tolerant) or TIM2_CH4
D4 Digital pin 4 PA7 GPIO (3V tolerant)
D5 Digital pin 5 or PWM PB9 TIM17_CH1
D6 Digital pin 6 or PWM PB8 TIM16_CH1
D7 Digital pin 7 PA6 GPIO (3V tolerant)
D8 Digital pin 8 PA5 GPIO (3V tolerant)
D9 Digital pin 9 or PWM PA4 TIM14_CH1
D10 Digital pin 10 or CS or PWM PA11 TIM1_CH4
D11 Digital pin 11 or MOSI or PWM PB5 SPI1_MOSI or TIM3_CH2
D12 Digital pin 12 or MISO PB4 SPI1_MISO
D13 Digital pin 13 or SCK PB3 SPI1_SCK
GND Reference Ground GND Reference Ground
AREF ADC voltage reference NC Not connected

Arduino ICSP connector 32F0308DISCOVERY

1 MISO PB4 SPI1_MISO

2 VCC 3.3V 3V VDD
3 SCK PB3 SPI1_SCK
4 MOSI PB5 SPI1_MOSI
5 RST NRST Reset discovery
6 GND GND Reference Ground

32/39 DocID025097 Rev 1

UM1658 Connecting modules on the prototyping board

Figure 12 illustrates the connections between the 32F0308DISCOVERY and the Arduino
shield boards.

Figure 12. Arduino shield board connections

DocID025097 Rev 1 33/39

38
Mechanical drawing UM1658

6 Mechanical drawing

Figure 13. 32F0308DISCOVERY mechanical drawing

MB1134 revA
STM32F0308-DISCO

34/39 DocID025097 Rev 1

 7
UM1658

ST_LINK_V2.SCHDOC
U_ST_LINK

MCO
MCO
PA10 PA14 TCK/SWCLK
PA10 PA14
PA9 PA13 TMS/SWDIO
PA9 PA13

NRST T_NRST
NRST
PB3 T_SWO
PB3

P1
1 3V
U_STM32Fx
2
VDD_3 STM32Fx.SchDoc P2
3
PC13 PA0 PB0
4 PA0 PB0 5V 1
PC14 PA1 PB1
5 PA1 PB1 2
PC15 PA2 PB2 PB9
6 PA2 PB2 3
PF0 PA3 PB3 PB8
7 PA3 PB3 4
PF1 PA4 PB4
8 PA4 PB4 VDD 5
PA5 PB5 BOOT0
9 PA5 PB5 6
NRST PA6 PB6 PB7
Electrical schematics

10 PA6 PB6 7
PC0 PA7 PB7 PB6
11 PA7 PB7 8
PC1 PA8 PB8 PB5
12 PA8 PB8 9
PC2 PA9 PB9 PB4
13 PA9 PB9 10
PC3 PA10 PB10 PB3
14 PA10 PB10 11
PA0 PA11 PB11 PD2
15 PA11 PB11 12
PA1 PA12 PB12 PC12
16 PA12 PB12 13
PA2 PA13 PB13 PC11
17 PA13 PB13 14
PA3 PA14 PB14 PC10
18 PA14 PB14 15
PF4 PA15 PB15 PA15

DocID025097 Rev 1
19 PA15 PB15 16
PF5 PA14
20 17
PA4 PC0 PD2 PF7
21 PC0 PD2 18
PA5 PC1 PF6
22 PC1 19
PA6 PC2 PF0 PA13
23 PC2 PF0 20
PA7 PC3 PF1 PA12
24 PC3 PF1 21
PC4 PC4 PF4 PA11
25 PC4 PF4 22
PC5 PC5 PF5 PA10
26 PC5 PF5 23
PB0 PC6 PF6 PA9
27 PC6 PF6 24
PB1 PC7 PF7 PA8
28 PC7 PF7 25
PB2 PC8 PC9
29 PC8 26
PB10 PC9 MCO PC8
Figure 14. 32F0308DISCOVERY

30 PC9 MCO 27
PB11 PC10 PC7
31 PC10 28
PB12 PC11 VDD_3 PC6
32 PC11 VDD_3 29
PC12 PB15
33 PC12 30
PC13 BOOT0 PB14
PC13 BOOT0 31
Header 33 PC14 PB13
PC14 32
PC15 NRST
PC15 NRST 33
Header 33

STMicroelectronics
Title:
STM32F030 DISCOVERY
Number:MB1134 Rev: A.1(PCB.SCH) Date: 7/4/2013 Sheet 1 of

35/39
Electrical schematics

38
36/39
TCK/SWCLK
PA14
TMS/SWDIO
PA13
T_NRST SWD
NRST
T_SWO SB19
R13 PB3
R18 10K Not Fitted SB22
Electrical schematics

100K
Board Ident: PC13=0 R9
R19 10K 10K D3
SWD R10 AIN_1
100

SWIM_IN
SWIM
SWIM_IN
SWIM_RST
SWIM_RST_IN
STM_JTCK
BAT60JFILM
CN3

DEFAULT
RESERVED
Not Fitted 3V
R12 T_JTCK

48
47
46
45
44
43
42
41
40
39
38
37
1 3V
U2 22 SB6 SB5
2
STM32F103C8T6 STM_JTCK SWCLK
3
SB8 SB7

PB9
PB8
PB7
PB6
PB5
4
R14 T_JTMS

VSS_3
5

VDD_3
BOOT0
C11 C10 22 SB10 SB9
6

PB3/JTDO
20pF

PA15/JTDI
20pF X1 1 36 R15 T_NRST STM_JTMS SWDIO
VBAT VDD_2 3V

PB4/JNTRST
3V 1 2 2 35 Header 6 22 SB12 SB11

JTCK/SWCLK
PC13 VSS_2
3 34 STM_JTMS R17 T_SWO
8MHz PC14 JTMS/SWDIO
4 33 USB_DP 22
PC15 PA12
R16 OSC_IN 5 32 USB_DM
OSCIN PA11
100K OSC_OUT 6 31 T_SWO
1
2
3
4

OSCOUT PA10
STM_RST 7 30 LED_STLINK RC Must be very close to STM32F103 pin 29
NRST PA9 R34
8 29 MCO
VSSA PA8 MCO
C8 9 28 100 CN2
3V VDDA PB15
100nF R20 4K7 AIN_1 10 27 T_JTMS C24
PA0 PB14
SB13 11 26 T_JTCK 20pF
PA1 PB13 R11
Jumpers ON --> DISCOVERY Selected
R21 4K7 12 25
PA2 PB12 100 Jumpers OFF --> ST-LINK Selected
Not Fitted
T_SWDIO_IN

PA3
PA4
PA5
PA6
PA7
PB0
PB1
PB2/BOOT1
PB10
PB11
VSS_1
VDD_1
STM32F0_USART1_RX

STLINK_TX

DocID025097 Rev 1
13
14
15
16
17
18
19
20
21
22
23
24
LD2
PA10
SB14 Idd Red
TX COM R4 2 1
3V
JP1 RX 3V JP2 VDD 100
STLINK_RX

T_JTCK
T_JTDO
T_JTDI
T_NRST
T_JRST
SWIM_IN
SWIM
PA9
SB15 R3
STM32F0_USART1_TX R2 LED_STLINK 3 4 R1
1K 3V
100 0
_Green
Not Fitted LD_BICOLOR_CMS
Close to JP LD1
Not Fitted RED
Figure 15. ST-LINK/V2 (SWD only)

PWR
USB 5V U1 D2 OUT_3V
1 Vin Vout 5
D1 3V
EXT_5V
3 INH BAT60JFILM
U5V 5V C1 C4
GND
BYPASS
CN1 BAT60JFILM 1 _X5R_0603 1 _X5R_0603
2
4

3V
1 R6 1K5 LD3985M33R
VCC 3V C3 C5
2 R8 0 USB_DM C2
D- C6 C7 C12 C9 100nF 10nF_X7R_0603 100nF
3 R7 0 USB_DP
D+ 100nF 100nF 100nF 100nF
4 R5 100K
ID
5
GND
0
SHELL
5075BMR-05-SM
STMicroelectronics
Title:
STM32F030 DISCOVERY ST-LINK/V2 (SWD only)
Number:MB1134 Rev: A.1(PCB.SCH) Date: 7/1/2013 Sheet 2 of 3
UM1658
 UM1658

LD3
PC9 R30

PF7
PF6
PA13
PA12
PA11
PA10
PA9
PA8
PC9
PC8
PC7
PC6
PB15
PB14
PB13
PB12
330
green

LD4
R31

PF7
PF6
PA13
PA12
PA11
PA10
PA9
PA8
PC9
PC8
PC7
PC6
PB15
PB14
PB13
PB12
PC8
660
blue

48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
U3
STM32F030R8T6

PF7
PF6
PC9
PC8
PC7
PC6

PA9
PA8
PB15
PB14
PB13
PB12

PA13
PA12
PA11
PA10
PA14 49 32
PA14 PA14 VDD_2 VDD
PA15 50 31
PA15 PA15 VSS_2
PC10 51 30 PB11
PC10 PC10 PB11 PB11
PC11 52 29 PB10 VDD
PC11 PC11 PB10 PB10
PC12 53 28 PB2 Not Fitted
PC12 PC12 PB2 or NPOR (1.8V mode) PB2
PD2 54 27 PB1
PD2 PD2 PB1 PB1 R33
Not Fitted PB3 55 26 PB0
PB3 PB3 PB0 PB0 100K
PB4 56 25 PC5
BOOT0 PB4 PB4 PC5 PC5
PB5 57 24 PC4
PB5 PB5 PC4 PC4
PB6 58 23 PA7 NRST
R27 PB6 PB6 PA7 PA7
PB7 59 22 PA6 SB4
2
1

VDD PB7 PB7 PA6 PA6

10K BOOT0 60 21 PA5
R26 BOOT0 PA5 PA5
PB8 61 20 PA4 B2
PB8 PB8 PA4 PA4
510 PB9 62 19 PF5 C23
PB9 PB9 PF5 PF5
63 18 PF4
VSS_1 PF4 PF4
SB2 64 17 PA3 100nF
VDD VDD_1 PA3 PA3
3
4
SW-PUSH-CMS

Not Fitted

VDD_3
PC13 - TAMPER1 - WKUP2
PC14 - OSC32_IN
PC15 - OSC32_OUT
PF0 - OSC_IN
PF1 - OSC_OUT
NRST
PC0
PC1
PC2
PC3
VSSA / VREF-
VDDA / VREF+
PA0 - TAMPER2 - WKUP1
PA1
PA2
C17
1uF SB1

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Close to STM32 Closed by default
PA2

DocID025097 Rev 1
VDD_3 PA2
PC13 PA1 RESET Button
PC13 PA1
PC14 SB21 PA0
PC14 PA0
PC15 SB20
PC15 VDD
Figure 16. MCU

PC3 VDD
PC3
Close to XTAL & MCU R25 X3 R24 PC2
PC2 R32
0 0 PC1
PC1
1 4 PC0 Not Fitted
2
1

PC0 100
C16 NRST
C15 NRST
2 3 B1
Not Fitted 6.8pF 6.8pF C22

100nF
MC306-G-06Q-32.768 (JFVNY)
3
4
SW-PUSH-CMS

PA0 R28
SB3 330
MCO PF1 VDD VDD
MCO PF1 R29
SB18 SB16
220K
R23 R22 C18 C20 C21 C19
PF0 0 X2 390 1uF 100nF 100nF 100nF
PF0
SB17 1 2

8MHz USER & WAKE-UP Button

C14 C13
Not Fitted 20pF 20pF

STMicroelectronics
Title:
STM32F030 DISCOVERY MCU
Number:MB1134 Rev: A.1(PCB.SCH) Date: 7/4/2013 Sheet 3 of 3

37/39
Electrical schematics

38
Revision history UM1658

8 Revision history

Table 11. Document revision history

Date Revision Changes

03-Sep-2013 1 Initial release.

38/39 DocID025097 Rev 1

UM1658

Please Read Carefully:

Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.

UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE
IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH
PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR
ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED
FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN
WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE,
AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS.
PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE
CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.

© 2013 STMicroelectronics - All rights reserved

STMicroelectronics group of companies

Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com

DocID025097 Rev 1 39/39

39