Electronic pressure switch RE 30276/03.

06
Replaces: 01.06
1/6

RE 30275
with integrated analogue output

Type HEDE 10…/1/

Component series 2X

tb0002

Table of contents Features

Contents Page – Suitable for measuring pressures and converting the measured
Features 1 values into electrical signal variables in hydraulic systems
Ordering code 2 – EMC properties allow the use of this pressure switch also in
critical applications
Technical data 2 and 3
– Ceramic / capacitive sensor
Pin assignment K41 3
– Connecting cable with 4-pin M12 plug on housing
Unit dimensions 4
– Accuracy class 1.0
Accessories 5 and 6
– Connection thread G1/4
– Parts in contact with media are made of stainless steel, ce-
ramic and FKM
– Compact design
– One switching output and one analogue output
2/6 Bosch Rexroth AG Hydraulics HEDE 10…/1/ RE 30276/03.06

Ordering code

HED E 10 A1 2X K41 G24 1 V *

Hydraulic Further details in clear

electrical text
pressure switch V= FKM seals
Integrated electronics =E Caution!
Component type = 10 Observe compatibility of
seals with hydraulic fluid used!
Hydraulic interface 1/4“ = A1
1= One switching and one analogue output
Component series = 2X
G 24 = Supply voltage
Pressure stages
Plug variant
100 bar = 100
K41 = M12, 4-pin as standard
250 bar = 200
400 bar = 400
600 bar = 600

Technical data (for applications outside these parameters, please consult us!)

Input variables
Auxiliary energy UO 18 to 36 VDC
Current consumption I < 50 mA
Measuring range pN in bar 100 250 400 600
Overload safety pmax in bar 300 400 600 800
Burst pressure p in bar 650 850 1000 1200
Output variables
Analogue output U 0 to 10 VDC minimum load 2000 Ω
I 4 – 20 mA (max. load (UO – 10) x 50 Ω)
Rise time (10 to 90 %) t 3 ms
Switching output Current carrying capacity I 250 mA
Response time t < 3 ms (with response time set to dAP = 3)
Max. switching frequency f 170 Hz (at dAP = 3)
Characteristic curve deviation: < ±0.5 %
(initial point setting according to DIN16086)
Temperature coefficient within nominal temperature range
– Highest TC of zero point 0.2 % / 10 k
– Highest TC of span 0.2 % / 10 k
Hysteresis < ±0.1 %
Repeatability 0.1 %
Long-term drift under reference conditions (6 months) 0.05 %
Ambient conditions
Limit temperature range ϑ –20 to +80 °C
Storage temperature range ϑ –40 to +100 °C
Medium temperature range ϑ –25 to +80 °C
Mechanical data
Pressure port G1/4
Electrical connection M12 plug-in connection
RE 30276/03.06 HEDE 10…/1/ Hydraulics Bosch Rexroth AG 3/6

Technical data (continued)

Programming options Hysteresis / window; normally open / normally closed; pick-
up, drop-out delay; attenuation; display unit / analogue output:
voltage or current
Pressure stages 100 250 400 600
Switching point SP bar 1.0 ... 100 2 ... 250 4 ... 400 6 ... 600
Release position, rP bar 0.5 ... 99.5 1 ... 249 2 ... 398 3 ... 597
In increments of bar 0.5 1 2 3
Adjustable response time of a switch- Response time (dAP) ms 3 ... 500
ing output and resulting switching
frequency Hz 170 ... 1
Adjustable delay time dS, dr s 0.0; 0.2 ... 50.0
Environmental compatibility
Type of protection / housing to IEC 60529 IP67
Class of protection EN 50178 III
Insulation resistance MΩ > 100 (500 VDC)
Resistane to shock to IEC 60068-2-27 g 50 g, 11 ms
Resistance to vibration to IEC 60068-2-6 g 20 g, 10 ... 2000 Hz
Switching cycles min. 100 million / 50 million with pressure stage 600 bar
Approval cULus
EMC EN 61000-4-2 ESD 4 / 8 kV
EN 61000-4-3 HF radiated 10 V/m
EN 61000-4-4 burst 2 kV
EN 61000-4-5 surge 0.5 / 1 kV
EN 61000-4-6 HF cable-bound 10 V
Housing material EPDM/X (Santoprene); FKM; PBTP (Pocan); PC (Macrolon);
V2A (1.4301)
Materials in contact with the medium V2A (1.4305); ceramic; FKM
Connection M12 plug-in connection, gold-plated contacts

Pin assignment K41

One switching and 1 BN
one analogue output: L+
4 BK

HEDE 10 2 WH

3 BU
L–

Detail of plug on the device: 2 1 BN Brown

2 WH White
3 1
3 BU Blue
4 4 BK Black
4/6 Bosch Rexroth AG Hydraulics HEDE 10…/1/ RE 30276/03.06

Unit dimensions (nominal dimensions in mm)

Ø 34 48
1 Status LEDs
2 4-digit alphanumerical dis-
play

M12 x 1
3 Programming key
4 Dimension for pressure
1 4 stage 100 bar and 250 bar
2
5 Dimension for pressure
3 stage 400 bar and 600 bar
91,5
(94)

M12 x 1

(59,8)
57,3
5

5 Recommended installation:
1,3

13,5
Vibration-free installation!
30
Ø 21,5
Ø 27 G1/4
Tightening torque
20 to 30 Nm
RE 30276/03.06 HEDE 10…/1/ Hydraulics Bosch Rexroth AG 5/6

Accessories
Cable sockets:

Technical data: Designation Material no.

Current carrying ca- 4A 04 POL (with 2 m cable) R900773031
pacity 15 42
Temperature range –25...90 °C 04 POL (with 5 m cable) R900779498

Ø10,5
Type of protection IP 67
Contacts CuZn
Contact surface Gold-plated M 12x1
Housing TPU
Seal FKM 04 POL (with 2 m cable) R900779504
15 27
Fitting CuZn/Ni 04 POL (with 5 m cable) R900779503
Wire cross-section 4 x 0,34 mm
Sheath material PUR

39
Shield Not connected
on plug side
M 12x1
Sheath diameter Ø 5.0 mm
Sheath colour Black
Bending radius for min. 50 mm Ø10,5
dyn. application
20 46 04 POL (without cable)1) R900773042
Connection:

1 BN
2
2 WH
M12x1
1 3 04 POL (without cable)1) R900779509
3 BU 20 36

4 BK 4
Ø18
30

M12x1 Ø15 1) Type of protection IP68

Hydraulic fitting:
Designation Material no. 17
AB 20-28 R900012451 22 19
G 1/4
5

2
12 O-ring
Elastic profiled seal 49
6/6 Bosch Rexroth AG Hydraulics HEDE 10…/1/ RE 30276/03.06

Accessories (continued)
Mounting clamp for HEDE 10
Designation Material no. 70
Mounting clamp R900786138

58
ø34
12
6,5

29
52

Protective cap for HEDE 10

Designation Material no.
45°
Protective cap M12 R900786141
ø37
35

ø16
ø3

Bosch Rexroth AG © This document, as well as the data, specifications and other information
Hydraulics set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be
Zum Eisengießer 1 reproduced or given to third parties without its consent.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No state-
Phone +49 (0) 93 52 / 18-0 ments concerning a certain condition or suitability for a certain application
Fax +49 (0) 93 52 / 18-23 58 can be derived from our information. The information given does not
[email protected] release the user from the obligation of own judgment and verification. It
www.boschrexroth.de must be remembered that our products are subject to a natural process of
wear and aging.
RE 30276/03.06 HEDE 10…/1/ Hydraulics Bosch Rexroth AG 7/6

Notes

Bosch Rexroth AG © This document, as well as the data, specifications and other information
Hydraulics set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be
Zum Eisengießer 1 reproduced or given to third parties without its consent.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No state-
Phone +49 (0) 93 52 / 18-0 ments concerning a certain condition or suitability for a certain application
Fax +49 (0) 93 52 / 18-23 58 can be derived from our information. The information given does not
[email protected] release the user from the obligation of own judgment and verification. It
www.boschrexroth.de must be remembered that our products are subject to a natural process of
wear and aging.
8/6 Bosch Rexroth AG Hydraulics HEDE 10…/1/ RE 30276/03.06

Notes

Bosch Rexroth AG © This document, as well as the data, specifications and other information
Hydraulics set forth in it, are the exclusive property of Bosch Rexroth AG. It may not be
Zum Eisengießer 1 reproduced or given to third parties without its consent.
97816 Lohr am Main, Germany The data specified above only serve to describe the product. No state-
Phone +49 (0) 93 52 / 18-0 ments concerning a certain condition or suitability for a certain application
Fax +49 (0) 93 52 / 18-23 58 can be derived from our information. The information given does not
[email protected] release the user from the obligation of own judgment and verification. It
www.boschrexroth.de must be remembered that our products are subject to a natural process of
wear and aging.