Session 8.2 - Slope Stabilzation

Slope Stabilization
Introduction
• Methods for stabilizing slopes depend on, and can be very limited by, factors
such as
— surface / groundwater hydrology and drainage potential
— slope geometry and constraints on alterations
— distribution of low strength material / strata in the slope
— the proposed development (if any) and / or reasons for trying to stabilize
the slope
— available technology, equipment and expertise
• Generally, stabilization involves one or more of,
— reducing pore pressures in the slope by surface and subsurface drainage
(will --> increase in shear strength)
— reducing disturbing forces, e.g., by reducing slope angle, removing material
from the upper part of the slope
Dr Wasantha, 2020 1
Slope Stabilization
Introduction ctd…
— increasing the resisting forces, e.g., by adding weight to the toe of the
slope, or by increasing the shear strength along potential failure surfaces
— supporting unstable areas by construction of retaining walls
— attempting to control slipping soil, rock, etc. (more a damage control rather
than stabilization technique)
Drainage and groundwater control

• Groundwater levels (and hence pore pressures) can be controlled by
subsurface drainage and/or reduction of infiltration
• Infiltration can be reduced by surface drainage or by soil treatment, e.g.,
compaction, impervious layer
Dr Wasantha, 2020 2
Slope Stabilization
Drainage and groundwater control ctd…
• Subsurface drainage methods include
— trench drains: trenches backfilled with permeable material (gravel), and
usually with slotted pipe - filter cloth often used to wrap pipe or pipe /
gravel as whole
lateral branches usually run across the slope to a collector running
downslope - can also have laterals angling in to collector from both sides
(herringbone)
Dr Wasantha, 2020 3
Slope Stabilization
— horizontal drains: drilled into a slope at an angle of
± 5o to the horizontal holes may be open in rock,
but would usually have pipes and filters in soil
— galleries / adits: a special case of the above used in dam abutments and
slopes for both drainage and inspection purposes
— wells / bores: can be pumped to lower a water table or reduce pressures in
artesian aquifers - often used more for regional groundwater control
— vegetation: deep-rooted plants (e.g., trees) can act as biological pumps and
control rising water tables - roots also provide soil reinforcement and
anchoring, etc.
Dr Wasantha, 2020 4
Slope Stabilization
• Surface water control methods include
— collection of runoff at the uphill boundary of any unstable area - is best
done with open impermeable channels (rather than unlined drains or
pipes) channels should be kept well back from the top of the slope, and
need good construction joints, flexibility
— maximising runoff from the unstable area, controlling and collecting this
runoff - compacted clay layers or impermeable membranes / liners may be
laid on the slope to minimise or prevent infiltration. Runoff must be
discharged so that it does not impact adversely on adjacent areas
— careful location of water pipes (consider consequences of a pipe burst or
leak - critical in the Thredbo slide)
Dr Wasantha, 2020 5
Slope Stabilization
Alteration of slope geometry
• could involve a general flattening of the slope, but there will often be
constraints at the top of the slope
• could remove material from higher in the slope --> stepped effect and weight
reduction (constraints)
• could add free-draining fill (e.g., coarse rock) at base of slope to increase force
resisting a slip, but again there will often be constraints against this
• It will usually be necessary to use a filter layer or cloth between the fill and
foundation material in the last case
• In some cases, it may even be possible to remove most / all of the unstable
material in the slope and replace it with stronger material
Dr Wasantha, 2020 6
Slope Stabilization
Stabilization by walling
• Retaining walls (to be discussed in more detail in Geotech Engineering) can be
used to help stabilize slopes
• Reinforced concrete walls can be used, but may look unsightly on natural
slopes unless their lines are broken up by overhanging vegetation, etc.
• Gabions and crib walls may look more attractive
• In each case stability can be increased by the use of ground anchors
Dr Wasantha, 2020 7
Slope Stabilization
Stabilization by reinforcement
• Includes techniques to improve the soil’s resistance to shearing and
deformation by inclusion of elements which resist tensile, compressive, shear
and bending forces
• Soil nailing - slender rods or angle sections are shot into the soil at various
angles
• Rock bolts and anchors - variation on the above where rods or cables are
grouted into holes drilled into stable material deeper within the slope
— usually are attached to individual small plates or broader mesh at the rock
face, which may be gunited
Dr Wasantha, 2020 8
Slope Stabilization
Stabilization by reinforcement ctd…
• Passive piles - piles are installed through the slipped material into the stable
material beneath to slow the rate of movement of the soil - should be close
enough to allow arching action to develop in the soil
• Micro-piles - boreholes (about 100mm diameter) are drilled through the
unstable material into the stable soil beneath
— they are filled with sand / cement grout and a single central reinforcing bar
— many are needed and can be quite expensive, but can be installed by small
equipment in confined spaces
— ground movement can lead to cracking, corrosion and failure
Dr Wasantha, 2020 9

Session 8.2 - Slope Stabilzation

Uploaded by

Copyright:

Available Formats

Session 8.2 - Slope Stabilzation

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Session 8.2 - Slope Stabilzation

Uploaded by

Copyright:

Available Formats

Slope Stabilization

Drainage and groundwater control

You might also like