100% found this document useful (1 vote)
91 views2 pages

Cep, Ecd2020

The document outlines 20 electronics design and implementation projects related to oscillators, power supplies, amplifiers, and signal processing. The projects include designing various oscillator circuits including Wein-Bridge, phase shift, Hartley, and Colpitts oscillators. Other projects involve designing power supplies, push-pull amplifiers, sampling and quantization of signals, and common emitter and common collector amplifier stages. The designs are aimed at generating sine waves and rectangular waves at specified frequencies and amplitudes.

Uploaded by

Osama Asghar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
100% found this document useful (1 vote)
91 views2 pages

Cep, Ecd2020

The document outlines 20 electronics design and implementation projects related to oscillators, power supplies, amplifiers, and signal processing. The projects include designing various oscillator circuits including Wein-Bridge, phase shift, Hartley, and Colpitts oscillators. Other projects involve designing power supplies, push-pull amplifiers, sampling and quantization of signals, and common emitter and common collector amplifier stages. The designs are aimed at generating sine waves and rectangular waves at specified frequencies and amplitudes.

Uploaded by

Osama Asghar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

CEP, ECD 2020

1. Exact design (by diode model) and implementation of alternative amplitude control circuit
for a Wein-Bridge Oscillator (using two parallel diodes) for a 8 KHz sine wave having +Vp =
7V while -Vp = 5V.
2. Design and implementation of a BJT based Phase shift oscillator for 8 KHz sinewave.
3. Design and implementation of a MOSFET based Phase shift oscillator for 8 KHz sinewave.
4. Design and implementation of an Op-Amp based Hartley oscillator for 2 MHz sinewave.
5. Design and implementation of an Op-Amp based Clapp oscillator for 4 MHz sinewave.
6. Design and implementation of a MOSFET based Hartley oscillator for 2 MHz sinewave.
7. Design and implementation of a BJT based Clapp oscillator for 4 MHz sinewave.
8. Design and implementation of a BJT based crystal oscillator for an 8 MHz sinewave.
9. Implementation of Colpitts oscillator using quartz crystal.
10. Generate a rectangular wave having +Vp = 7V while -Vp = 5V with f= 8 KHz and DC = 35% by
designing and developing an Op-Amp based astable multivibrator.
11. Generate a rectangular wave having +Vp = 5.5V while -Vp = 7.5V with f= 5 KHz and DC = 35%
by designing and developing a 555 Timer based Astable multivibrator.
12. Design and implementation of a regulated power supply by precession rectification for -10V.
Ensure that not a single Op-Amp will saturate during a whole period of the input cycle. Use
an appropriate filtration circuit following by 3 pin regulator to get -10V DC supply.
13. Design and Implementation of a push pull (class B) stage using TIP31 and TIP32 for a load
current of 1A by removing crossover distortion through negative feedback.
14. Design and Implementation of a transformer coupled (at input and output) push pull (class
B) stage using TIP31 and TIP32 for a load current of 1A and compare its efficiency with that
of the direct coupled amplifier.
15. Design and implementation a Transformer coupled Class A power amplifier to drive a load
of 4Ω/10w from 20mA input signal.
16. Design and implementation of an audio power amplifier: a class AB output stage to drive a
4Ω/10w speaker from 20mA input signal.
1
17. Develop a plant of transfer function (𝑠 2+3𝑠+2)
in LtSpice using inverting integrators and

inverting summers. Give a 1V DC signal to see its step response. Find the step response of
the same mathematical model in Matlab to verify the implementation.
18. Take an AC voltage supply of ±7.5V. Sample_&_hold it, digitize it by an 8-bit ADC and then
convert it back to analog signal by an 8-bit DAC. Plot both the sampled_&_hold signal and
DAC output signal on a single graph to compare the signals.
19. Design a Common Emitter amplifier stage for the following set of specifications.
1. Maximum input voltage swing: ±100mV
2. Mid-band Voltage gain: 100V/V
3. Lower cut-off frequency: 100Hz
4. Upper cutoff frequency: >20kHz
5. Input impedance: >2kΩ
Output impedance: <1kΩ
20. Design and Implementation of a Common Collector Amplifier for the following Set of
Specifications.
1. Maximum input voltage swing: ±10V
2. Load resistance: 250Ω
3. Lower cut-off frequency: 100Hz
4. Upper cutoff frequency: >20kHz
5. Input impedance: >2kΩ
6. Maximum collector current : <100mA

You might also like