Scribd
Upload
102 views6 pages

01-56 Code Control Module PDF

The document provides instructions for coding an ABS/EDL control module according to the vehicle's engine and transmission type. It explains that if a control module has been replaced or a specific diagnostic trouble code is present, the module must be coded using the workshop number from the VAG1551 scan tool. A coding table lists the code numbers needed for different engine and transmission combinations. Technicians are instructed to select the coding function from the scan tool menu and enter the appropriate code to match the vehicle.

Uploaded by

mefisto06c
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
102 views6 pages

01-56 Code Control Module PDF

The document provides instructions for coding an ABS/EDL control module according to the vehicle's engine and transmission type. It explains that if a control module has been replaced or a specific diagnostic trouble code is present, the module must be coded using the workshop number from the VAG1551 scan tool. A coding table lists the code numbers needed for different engine and transmission combinations. Technicians are instructed to select the coding function from the scan tool menu and enter the appropriate code to match the vehicle.

Uploaded by

mefisto06c
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Code Control Module (function 07) Page 1 of 6

01-56

Code Control Module


(function 07)
Has an ASR control module just been replaced
or is the following DTC stored in DTC memory of
the control module?

"ABS/EDL transmission electrical connection"

If so, control module must be coded according to


engine and transmission type.

Note:

Coding is only possible if a workshop number is


stored in the VAG1551 Scan Tool (ST).

Operating instructions for VAG1551

The ABS/EDL/ASR control module with index


"N" was implemented in 05.95 along with
implementation of the automatic transmission
01V for vehicles equipped with ASR. The
coding versions of this control module were
expanded to include automatic transmission
01V.

Control modules with index "N" can replace


previous control modules with index "M" as

http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU02.01.7 11/20/2002
Code Control Module (function 07) Page 2 of 6

necessary.

For vehicles prior to 05.95, control modules with


index "M" will no longer be available after
current supplies are exhausted.

http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU02.01.7 11/20/2002
Code Control Module (function 07) Page 3 of 6

01-57

- Connect the VAG1551 Scan Tool (ST) and


select "Brake Electronics" via address word 03
page 01-4 .

- Check the control module version page 01-52


and press the button.

Notes:

During control module identification, a 3 or 5-


digit code must always be indicated.

If control module does not indicate coding


corresponding to vehicle, or if control module
has been replaced, code it as follows.

Rapid data transfer HELP Indicated on display:


Select function XX
- Press buttons -0- and -7- to select "Code control module" function 03.

Rapid data transfer Q Indicated on display:


07 - Code control module
- Press -Q- button to confirm input.

Code control module Q Indicated on display:


Enter code number XXXXX
- Enter the appropriate code number and press -Q- button to confirm
input.

http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU02.01.7 11/20/2002
Code Control Module (function 07) Page 4 of 6

01-58

Coding table

Engine Transmission Data Control module Code Note:


transmission part number number
via: with index
2.6 6 2V Manual 012 single wires 4D0 907 M; 00000 Terminal 45 at ABS
Liter Cyl. transmission 379 N control module (w/EDL) -
J104- not occupied.
Automatic 01V single wires 4D0 907 N 00003 Terminal 45 at ABS
transmission 379 control module (w/EDL) -
J104- occupied with 12V.
2.8 6 2V Manual 012 single wires 4D0 907 M; 00000 Terminal 45 at ABS
Liter Cyl. transmission 379 N control module (w/EDL) -
J104- not occupied.
Automatic 01V single wires 4D0 907 N 00003 Terminal 45 at ABS
transmission 379 control module (w/EDL) -
J104- occupied with 12V.

http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU02.01.7 11/20/2002
Code Control Module (function 07) Page 5 of 6

01-59

Engine Transmission Data Control module Code Note:


transmission part number number
via: with index
2.8 6 5V Manual 012 single wires 4D0 907 N 00000 Terminal 45 at ABS
Liter Cyl. transmission 379 control module (w/EDL) -
J104- not occupied.
Automatic 01V single wires 4D0 907 N 00003 Terminal 45 at ABS
transmission 379 control module (w/EDL) -
J104- occupied with 12V.

http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU02.01.7 11/20/2002
Code Control Module (function 07) Page 6 of 6

01-60

4D0 907 379 X Syst. ident. Software ver. Display will indicate the control module identification and the coding
Coding 00000 WSCXXXXX entered (e.g. 00000).

- Press button.

Rapid data transfer HELP Indicated on display:


Select function XX
- Press buttons -0- and -6- to select "End Output" function 06. Press -Q-
button to confirm input.

http://127.0.0.1:8080/audi/servlet/Display?action=Goto&type=repair&id=AUDI.B5.SU02.01.7 11/20/2002

You might also like