Chemistry

GCSE
CHEMISTRY
(8462)
Specification
For teaching from September 2016 onwards
For exams in 2018 onwards
Version 1.0 22 April 2016

GCSE Chemistry (8462). For exams 2018 onwards. Version 1.0
Contents
1 Introduction 5
1.1 Why choose AQA for GCSE Chemistry 5
1.2 Support and resources to help you teach 6
2 Specification at a glance 8
2.1 Subject content 8
2.2 Assessments 8
3 Working scientifically 9
4 Subject content 15
4.1 Atomic structure and the periodic table 16
4.2 Bonding, structure, and the properties of matter 24
4.3 Quantitative chemistry 33
4.4 Chemical changes 40
4.5 Energy changes 47
4.6 The rate and extent of chemical change 50
4.7 Organic chemistry 56
4.8 Chemical analysis 65
4.9 Chemistry of the atmosphere 70
4.10 Using resources 74
4.11 Key ideas 83
5 Scheme of assessment 84
5.1 Aims and learning outcomes 84
5.2 Assessment objectives 85
5.3 Assessment weightings 86
6 General administration 87
6.1 Entries and codes 87
6.2 Overlaps with other qualifications 87
6.3 Awarding grades and reporting results 87
6.4 Re-sits and shelf life 88
6.5 Previous learning and prerequisites 88
6.6 Access to assessment: diversity and inclusion 88
6.7 Working with AQA for the first time 88
6.8 Private candidates 89
7 Mathematical requirements 90
Visit aqa.org.uk/8462 for the most up-to-date specification, resources, support and administration 3
8 Practical assessment 91
8.1 Use of apparatus and techniques 92
8.2 Required practical activities 93
9 Appendix A: periodic table 99
Are you using the latest version of this specification?

• You will always find the most up-to-date version of this specification on our website at
aqa.org.uk/8462
• We will write to you if there are significant changes to this specification.
4 Visit aqa.org.uk/8462 for the most up-to-date specification, resources, support and administration
1 Introduction
1.1 Why choose AQA for GCSE Chemistry
Our philosophy: science for all
We believe that science has something to offer every student. That’s why we have a suite of science
qualifications for Key Stage 4 – to suit students of all abilities and all aspirations.
You'll see that our GCSE Chemistry, along with Biology and Physics, is a clear straightforward
specification, with clear straightforward exams, so all your students can realise their potential.
Our specification has been developed with teachers

We’ve involved over a thousand teachers in developing our specification, exams and resources.
So you can be confident that our GCSE Chemistry is relevant and interesting to teach and to learn.
We’ve ensured that:
• the subject content is presented clearly, in a logical teaching order. We’ve also given teaching
guidance and signposted opportunities for skills development throughout the specification
• the subject content and required practicals in our GCSE Combined Science: Trilogy are also in
our GCSE Biology, Chemistry and Physics. So you have the flexibility to co-teach or to move your
students between courses
• all our science qualifications provide opportunities for progression. Our GCSE includes progression
in the subject content and consistency in the exam questions, so that your students have the best
preparation for A-level.
Our practicals have been trialled by teachers

There’s no better way to learn about science than through purposeful practical activities as part of
day-to-day teaching and learning. Our eight required practicals:
• are clearly laid out in the specification, so you know exactly what’s required
• are deliberately open, so you can teach in the way that suits you and your students
• have already been trialled in schools.
You’ll find even more support and guidance in our practical handbook, which includes
recommendations and advice from teachers in the trial.
Straightforward exams, so students can give straightforward answers

We’ve improved our question papers. You’ll find that our exams:
• use more straightforward language and fewer words so they’re easier to understand
• have fewer contexts so students don’t get confused
• have questions that increase in difficulty so students feel confident
• have been written with our GCSE Mathematics and A-level science teams, so students have
consistency between content and questions.
Over 3,000 students have sat our specimen question papers and they agree that they’re clearer and
more straightforward than ever.
We don’t profit from education – you do
We are an educational charity focused on the needs of teachers and students. This means that we
spend our income on improving the quality of our specifications, exams, resources and support.
You can find out all about our science qualifications at aqa.org.uk/science
1.2 Support and resources to help you teach

We’ve worked with experienced teachers to provide you with a range of resources that will help you
confidently plan, teach and prepare for exams.
Teaching resources
Visit aqa.org.uk/8462 to see all our teaching resources. They include:
• additional practice papers to help students prepare for exams
• schemes of work, written by experienced teachers
• a practical handbook, including recommendations and advice from teachers who’ve trialled our
practicals
• AQA-approved textbooks reviewed by experienced senior examiners
• subject expertise courses for all teachers, from newly qualified teachers who are just getting started
to experienced teachers looking for fresh inspiration.
Preparing for exams

Visit aqa.org.uk/8462 for everything you need to prepare for our exams, including:
• past papers, mark schemes and examiners’ reports
• specimen papers and mark schemes for new courses
• Exampro: a searchable bank of past AQA exam questions
• exemplar student answers with examiner commentaries.
Analyse your students' results with Enhanced Results Analysis (ERA)

Find out which questions were the most challenging, how the results compare to previous years and
where your students need to improve. ERA, our free online results analysis tool, will help you see where
to focus your teaching. Register at aqa.org.uk/era
For information about results, including maintaining standards over time, grade boundaries and our
post-results services, visit aqa.org.uk/results
Keep your skills up-to-date with professional development

Wherever you are in your career, there’s always something new to learn. As well as subject-specific
training, we offer a range of courses to help boost your skills.
• Improve your teaching skills in areas including differentiation, teaching literacy and meeting Ofsted
requirements.
• Prepare for a new role with our leadership and management courses.
You can attend a course at venues around the country, in your school or online – whatever suits your
needs and availability. Find out more at coursesandevents.aqa.org.uk
Help and support available

Visit our website for information, guidance, support and resources at aqa.org.uk/8462
If you'd like us to share news and information about this qualification, sign up for emails and updates at
aqa.org.uk/keepinformedscience
Alternatively, you can call or email our subject team direct.
E: [email protected]
T: 01483 477 756
2 Specification at a glance
This qualification is linear. Linear means that students will sit all their exams at the end of the course.
2.1 Subject content

1 Atomic structure and the periodic table (page 16)
2 Bonding, structure, and the properties of matter (page 24)
3 Quantitative chemistry (page 33)
4 Chemical changes (page 40)
5 Energy changes (page 47)
6 The rate and extent of chemical change (page 50)
7 Organic chemistry (page 56)
8 Chemical analysis (page 65)
9 Chemistry of the atmosphere (page 70)
10 Using resources (page 74)
11 Key ideas (page 83)
2.2 Assessments
Paper 1: + Paper 2:
What's assessed What's assessed
Topics 1 – 5: Atomic structure and the periodic Topics 6 – 10: The rate and extent of chemical
table; Bonding, structure, and the properties change; Organic chemistry; Chemical analysis,
of matter; Quantitative chemistry, Chemical Chemistry of the atmosphere; and Using
changes; and Energy changes. resources.
How it's assessed How it's assessed
• Written exam: 1 hour 45 minutes • Written exam: 1 hour 45 minutes
• Foundation and Higher Tier • Foundation and Higher Tier
• 100 marks • 100 marks
• 50 % of GCSE • 50 % of GCSE
Questions Questions
Multiple choice, structured, closed short Multiple choice, structured, closed short
answer and open response. answer and open response.
3 Working scientifically
Science is a set of ideas about the material world. We have included all the parts of what good science
is at GCSE level: whether it be investigating, observing, experimenting or testing out ideas and thinking
about them. The way scientific ideas flow through the specification will support you in building a deep
understanding of science with your students. We know this will involve talking about, reading and
writing about science plus the actual doing, as well as representing science in its many forms both
mathematically and visually through models.
This specification encourages the development of knowledge and understanding in science through
opportunities for working scientifically. Working scientifically is the sum of all the activities that scientists
do. We feel it is so important that we have woven it throughout our specification and written papers.
Our schemes of work will take this further for you and signpost a range of ways to navigate through
this qualification so your students are engaged and enthused. These free resources support the use
of mathematics as a tool for thinking through the use of mathematical language in explanations,
applications and evaluations.
The tables below show examples of the ways working scientifically could be assessed.
1 Development of scientific thinking

Students should be able to: Examples of what students could be asked to do
in an exam
WS 1.1 Give examples to show how scientific methods and
Understand how scientific methods and theories have changed over time.
theories develop over time.
Explain, with an example, why new data from
experiments or observations led to changes in
models or theories.
Decide whether or not given data supports a
particular theory.
WS 1.2 Recognise/draw/interpret diagrams.
Use a variety of models such as
Translate from data to a representation with a model.
representational, spatial, descriptive,
computational and mathematical to solve Use models in explanations, or match features of a
problems, make predictions and to develop model to the data from experiments or observations
scientific explanations and understanding of that the model describes or explains.
familiar and unfamiliar facts.
Make predictions or calculate quantities based on
the model or show its limitations.
Give examples of ways in which a model can be
tested by observation or experiment.
WS 1.3 Explain why data is needed to answer scientific
Appreciate the power and limitations of questions, and why it may be uncertain, incomplete
science and consider any ethical issues which or not available.
may arise.
Outline a simple ethical argument about the rights
and wrongs of a new technology.
in an exam
WS 1.4 Describe and explain specified examples of the
Explain everyday and technological technological applications of science.
applications of science; evaluate associated
Describe and evaluate, with the help of data,
personal, social, economic and environmental
methods that can be used to tackle problems
implications; and make decisions based on
caused by human impacts on the environment.
the evaluation of evidence and arguments.
WS 1.5 Give examples to show that there are hazards
Evaluate risks both in practical science associated with science-based technologies which
and the wider societal context, including have to be considered alongside the benefits.
perception of risk in relation to data and
Suggest reasons why the perception of risk is often
consequences.
very different from the measured risk (eg voluntary vs
imposed risks, familiar vs unfamiliar risks, visible vs
invisible hazards).
WS 1.6 Explain that the process of peer review helps to
Recognise the importance of peer review of detect false claims and to establish a consensus
results and of communicating results to a about which claims should be regarded as valid.
range of audiences.
Explain that reports of scientific developments in the
popular media are not subject to peer review and
may be oversimplified, inaccurate or biased.
2 Experimental skills and strategies

in an exam
WS 2.1 Suggest a hypothesis to explain given observations
Use scientific theories and explanations to or data.
develop hypotheses.
WS 2.2 Describe a practical procedure for a specified
Plan experiments or devise procedures to purpose.
make observations, produce or characterise
Explain why a given practical procedure is well
a substance, test hypotheses, check data or
designed for its specified purpose.
explore phenomena.
Explain the need to manipulate and control variables.
Identify in a given context:
• the independent variable as the one that is
changed or selected by the investigator
• the dependent variable that is measured for each
change in the independent variable
• control variables and be able to explain why they
are kept the same.
Apply understanding of apparatus and techniques to
suggest a procedure for a specified purpose.
WS 2.3 Describe/suggest/select the technique, instrument,
Apply a knowledge of a range of techniques, apparatus or material that should be used for a
instruments, apparatus, and materials to particular purpose, and explain why.
select those appropriate to the experiment.
WS 2.4 Identify the main hazards in specified practical
Carry out experiments appropriately having contexts.
due regard for the correct manipulation of
Suggest methods of reducing the risk of harm in
apparatus, the accuracy of measurements
practical contexts.
and health and safety considerations.
WS 2.5 Suggest and describe an appropriate sampling
Recognise when to apply a knowledge of technique in a given context.
sampling techniques to ensure any samples
collected are representative.
WS 2.6 Read measurements off a scale in a practical context
Make and record observations and and record appropriately.
measurements using a range of apparatus
and methods.
WS 2.7 Assess whether sufficient, precise measurements
Evaluate methods and suggest possible have been taken in an experiment.
improvements and further investigations.
Evaluate methods with a view to determining
whether or not they are valid.
3 Analysis and evaluation
Apply the cycle of collecting, presenting and analysing data, including:

in an exam
WS 3.1 Construct and interpret frequency tables and
Presenting observations and other data using diagrams, bar charts and histograms.
appropriate methods.
Plot two variables from experimental or other data.
WS 3.2 Translate data between graphical and numeric form.
Translating data from one form to another.
WS 3.3 For example:
Carrying out and represent mathematical and • use an appropriate number of significant figures
statistical analysis. • find the arithmetic mean and range of a set of
data
• construct and interpret frequency tables and
diagrams, bar charts and histograms
• make order of magnitude calculations
• change the subject of an equation
• substitute numerical values into algebraic
equations using appropriate units for physical
quantities
• determine the slope and intercept of a linear
graph
• draw and use the slope of a tangent to a curve as
a measure of rate of change
• understand the physical significance of area
between a curve and the x-axis and measure it by
counting squares as appropriate.
WS 3.4 Apply the idea that whenever a measurement is
Representing distributions of results and made, there is always some uncertainty about the
make estimations of uncertainty. result obtained.
Use the range of a set of measurements about the
mean as a measure of uncertainty.
WS 3.5 Use data to make predictions.
Interpreting observations and other data
Recognise or describe patterns and trends in data
(presented in verbal, diagrammatic, graphical,
presented in a variety of tabular, graphical and other
symbolic or numerical form), including
forms.
identifying patterns and trends, making
inferences and drawing conclusions. Draw conclusions from given observations.
WS 3.6 Comment on the extent to which data is consistent
Presenting reasoned explanations including with a given hypothesis.
relating data to hypotheses.
Identify which of two or more hypotheses provides a
better explanation of data in a given context.

in an exam
WS 3.7 Apply the following ideas to evaluate data to suggest
Being objective, evaluating data in terms improvements to procedures and techniques.
of accuracy, precision, repeatability and • An accurate measurement is one that is close to
reproducibility and identifying potential the true value.
sources of random and systematic error. • Measurements are precise if they cluster closely.
• Measurements are repeatable when repetition,
under the same conditions by the same
investigator, gives similar results.
• Measurements are reproducible if similar results
are obtained by different investigators with
different equipment.
• Measurements are affected by random error
due to results varying in unpredictable ways;
these errors can be reduced by making more
measurements and reporting a mean value.
• Systematic error is due to measurement results
differing from the true value by a consistent
amount each time.
• Any anomalous values should be examined to try
to identify the cause and, if a product of a poor
measurement, ignored.
WS 3.8 Present coherent and logically structured responses,
Communicating the scientific rationale for using the ideas in 2 Experimental skills and
investigations, methods used, findings and strategies and 3 Analysis and evaluation, applied
reasoned conclusions through paper-based to the required practicals, and other practical
and electronic reports and presentations investigations given appropriate information.
using verbal, diagrammatic, graphical,
numerical and symbolic forms.
4 Scientific vocabulary, quantities, units, symbols and
nomenclature
in an exam
WS 4.1 The knowledge and skills in this section apply across
Use scientific vocabulary, terminology and the specification, including the required practicals.
definitions.
WS 4.2
Recognise the importance of scientific
quantities and understand how they are
determined.
WS 4.3
Use SI units (eg kg, g, mg; km, m, mm; kJ,
J) and IUPAC chemical nomenclature unless
inappropriate.
WS 4.4
Use prefixes and powers of ten for orders of
magnitude (eg tera, giga, mega, kilo, centi,
milli, micro and nano).
WS 4.5
Interconvert units.
WS 4.6
Use an appropriate number of significant
figures in calculation.
4 Subject content
This specification is presented in a two column format. The left hand column contains the
specification content that all students must cover and that can be assessed in the written papers.
The right hand column exemplifies some key opportunities for the following skills to be developed:
WS refers to Working scientifically, MS refers to Mathematical requirements and AT refers to
Use of apparatus and techniques. These are not the only opportunities. Teachers are encouraged to
introduce all of these skills where appropriate throughout the course.
Each topic begins with an overview. The overview puts the topic into a broader context and is intended
to encourage an overarching approach to both the teaching and learning of each of the topic areas. It is
not directly assessed. Any assessable content in this overview is replicated in the left hand column.
Most of the content is co-teachable with GCSE Combined Science: Trilogy. Content that is only
applicable to chemistry is indicated by (chemistry only) either next to the topic heading where it applies
to the whole topic or immediately preceding each paragraph or bullet point as applicable. Content
that is only applicable to Higher Tier is indicated by (HT only) either next to the topic heading where it
applies to the whole topic or immediately preceding each paragraph or bullet point as applicable.
It is good practice to teach and develop all of the mathematical skills throughout the course.
Some mathematical skills will only be assessed in certain subject areas. These are detailed in
Mathematical requirements.
Science is a practical subject. Details of the assessment of required practicals can be found in
Required practical activities. Working scientifically and Use of apparatus and techniques skills will be
assessed across all papers.
In chemistry paper 2 students will be expected to know and understand some basic
concepts and principles from topics in paper 1: Atomic structure and the periodic table,
Bonding, structure, and the properties of matter and Quantitative chemistry.
They should be able to recall and use this knowledge in questions that link and use these principles as
elements of explanations, in either paper. Students should expect to see questions based on some of
these basic principles in the second paper.
4.1 Atomic structure and the periodic table
The periodic table provides chemists with a structured organisation of the known chemical elements
from which they can make sense of their physical and chemical properties. The historical development
of the periodic table and models of atomic structure provide good examples of how scientific ideas and
explanations develop over time as new evidence emerges. The arrangement of elements in the modern
periodic table can be explained in terms of atomic structure which provides evidence for the model of a
nuclear atom with electrons in energy levels.
4.1.1 A simple model of the atom, symbols, relative atomic mass,

electronic charge and isotopes
4.1.1.1 Atoms, elements and compounds
Content Key opportunities for skills
development
All substances are made of atoms. An atom is the smallest part of an
element that can exist.
Atoms of each element are represented by a chemical symbol, eg O
represents an atom of oxygen, Na represents an atom of sodium.
There are about 100 different elements. Elements are shown in the
periodic table.
Compounds are formed from elements by chemical reactions.
Chemical reactions always involve the formation of one or more
new substances, and often involve a detectable energy change.
Compounds contain two or more elements chemically combined
in fixed proportions and can be represented by formulae using the
symbols of the atoms from which they were formed. Compounds can
only be separated into elements by chemical reactions.
Chemical reactions can be represented by word equations or
equations using symbols and formulae.
Students will be supplied with a periodic table for the exam and
should be able to:
• use the names and symbols of the first 20 elements in the periodic
table, the elements in Groups 1 and 7, and other elements in this
specification
• name compounds of these elements from given formulae or
symbol equations
• write word equations for the reactions in this specification
• write formulae and balanced chemical equations for the reactions
in this specification.
(HT only) write balanced half equations and ionic equations where
appropriate.
4.1.1.2 Mixtures
development
A mixture consists of two or more elements or compounds not WS 2.2, 2.3
chemically combined together. The chemical properties of each AT 4
substance in the mixture are unchanged.
Safe use of a range of
Mixtures can be separated by physical processes such as equipment to separate
filtration, crystallisation, simple distillation, fractional distillation and chemical mixtures.
chromatography. These physical processes do not involve chemical
reactions and no new substances are made.
Students should be able to:
• describe, explain and give examples of the specified processes of
separation
• suggest suitable separation and purification techniques for
mixtures when given appropriate information.
4.1.1.3 The development of the model of the atom (common content with physics)
development
New experimental evidence may lead to a scientific model being WS 1.1, 1.6
changed or replaced. This historical context
provides an opportunity
Before the discovery of the electron, atoms were thought to be tiny
for students to show an
spheres that could not be divided.
understanding of why and
The discovery of the electron led to the plum pudding model of the describe how scientific
atom. The plum pudding model suggested that the atom is a ball of methods and theories
positive charge with negative electrons embedded in it. develop over time.
The results from the alpha particle scattering experiment led to the WS1.2
conclusion that the mass of an atom was concentrated at the centre
(nucleus) and that the nucleus was charged. This nuclear model
replaced the plum pudding model.
Niels Bohr adapted the nuclear model by suggesting that electrons
orbit the nucleus at specific distances. The theoretical calculations of
Bohr agreed with experimental observations.
Later experiments led to the idea that the positive charge of any
nucleus could be subdivided into a whole number of smaller particles,
each particle having the same amount of positive charge. The name
proton was given to these particles.
The experimental work of James Chadwick provided the evidence to
show the existence of neutrons within the nucleus. This was about
20 years after the nucleus became an accepted scientific idea.
Students should be able to describe:
• why the new evidence from the scattering experiment led to a WS 1.1
change in the atomic model
development
• the difference between the plum pudding model of the atom and WS 1.2
the nuclear model of the atom.
Details of experimental work supporting the Bohr model are not
required.
Details of Chadwick’s experimental work are not required.
4.1.1.4 Relative electrical charges of subatomic particles

development
The relative electrical charges of the particles in atoms are:
In an atom, the number of electrons is equal to the number of protons

in the nucleus. Atoms have no overall electrical charge.
The number of protons in an atom of an element is its atomic number.
All atoms of a particular element have the same number of protons.
Atoms of different elements have different numbers of protons.
Students should be able to use the nuclear model to describe atoms. WS 1.2
4.1.1.5 Size and mass of atoms

development
Atoms are very small, having a radius of about 0.1 nm (1 x 10-10 m). WS 4.3, 4.4
Use SI units and the prefix
The radius of a nucleus is less than 1/10 000 of that of the atom
nano.
(about 1 x 10-14 m).
MS 1b
Almost all of the mass of an atom is in the nucleus.
Recognise expressions in
The relative masses of protons, neutrons and electrons are: standard form.
The sum of the protons and neutrons in an atom is its mass number.
Atoms of the same element can have different numbers of neutrons;
these atoms are called isotopes of that element.
Atoms can be represented as shown in this example:
Students should be able to calculate the numbers of protons,

neutrons and electrons in an atom or ion, given its atomic number and
mass number.
Students should be able to relate size and scale of atoms to objects in MS 1d
the physical world.
4.1.1.6 Relative atomic mass

development
The relative atomic mass of an element is an average value that takes
account of the abundance of the isotopes of the element.
Students should be able to calculate the relative atomic mass of an
element given the percentage abundance of its isotopes.
4.1.1.7 Electronic structure
development
The electrons in an atom occupy the lowest available energy levels WS 1.2
(innermost available shells). The electronic structure of an atom can be Students should be able
represented by numbers or by a diagram. For example, the electronic to represent the electronic
structure of sodium is 2,8,1 or structures of the first twenty
elements of the periodic
table in both forms.
MS 5b
Visualise and represent 2D
and 3D forms including two-
dimensional representations
of 3D objects.
showing two electrons in the lowest energy level, eight in the second
energy level and one in the third energy level.
Students may answer questions in terms of either energy levels or
shells.
4.1.2 The periodic table

4.1.2.1 The periodic table
development
The elements in the periodic table are arranged in order of atomic
(proton) number and so that elements with similar properties are
in columns, known as groups. The table is called a periodic table
because similar properties occur at regular intervals.
Elements in the same group in the periodic table have the same
number of electrons in their outer shell (outer electrons) and this gives
them similar chemical properties.
Students should be able to: WS 1.2
• explain how the position of an element in the periodic table is
related to the arrangement of electrons in its atoms and hence to
its atomic number
• predict possible reactions and probable reactivity of elements from
their positions in the periodic table.
4.1.2.2 Development of the periodic table

development
Before the discovery of protons, neutrons and electrons, scientists WS 1.1, 1.6
attempted to classify the elements by arranging them in order of their Explain how testing a
atomic weights. prediction can support or
refute a new scientific idea.
The early periodic tables were incomplete and some elements were
placed in inappropriate groups if the strict order of atomic weights
was followed.
Mendeleev overcame some of the problems by leaving gaps for
elements that he thought had not been discovered and in some
places changed the order based on atomic weights.
Elements with properties predicted by Mendeleev were discovered
and filled the gaps. Knowledge of isotopes made it possible to explain
why the order based on atomic weights was not always correct.
Students should be able to describe these steps in the development
of the periodic table.
4.1.2.3 Metals and non-metals

development
Elements that react to form positive ions are metals.
Elements that do not form positive ions are non-metals.
The majority of elements are metals. Metals are found to the left
and towards the bottom of the periodic table. Non-metals are found
towards the right and top of the periodic table.
• explain the differences between metals and non-metals
on the basis of their characteristic physical and chemical
properties. This links to Group 0, Group 1, Group 7 and
Bonding, structure and the properties of matter
• explain how the atomic structure of metals and non-metals relates
to their position in the periodic table
• explain how the reactions of elements are related to the
arrangement of electrons in their atoms and hence to their atomic
number.
4.1.2.4 Group 0
development
The elements in Group 0 of the periodic table are called the noble
gases. They are unreactive and do not easily form molecules because
their atoms have stable arrangements of electrons. The noble gases
have eight electrons in their outer shell, except for helium, which has
only two electrons.
The boiling points of the noble gases increase with increasing relative
atomic mass (going down the group).
• explain how properties of the elements in Group 0 depend on the
outer shell of electrons of the atoms
• predict properties from given trends down the group.
4.1.2.5 Group 1
development
The elements in Group 1 of the periodic table are known as the alkali
metals and have characteristic properties because of the single
electron in their outer shell.
Students should be able to describe the reactions of the first three
alkali metals with oxygen, chlorine and water.
In Group 1, the reactivity of the elements increases going down the
group.
4.1.2.6 Group 7
development
The elements in Group 7 of the periodic table are known as the AT 6
halogens and have similar reactions because they all have seven Offers an opportunity within
electrons in their outer shell. The halogens are non-metals and consist displacement reactions of
of molecules made of pairs of atoms. halogens.
Students should be able to describe the nature of the compounds
formed when chlorine, bromine and iodine react with metals and
non-metals.
In Group 7, the further down the group an element is the higher its
relative molecular mass, melting point and boiling point.
In Group 7, the reactivity of the elements decreases going down the
group.
A more reactive halogen can displace a less reactive halogen from an
aqueous solution of its salt.
4.1.3 Properties of transition metals (chemistry only)

4.1.3.1 Comparison with Group 1 elements
development
The transition elements are metals with similar properties which are
different from those of the elements in Group 1.
Students should be able to describe the difference compared with
Group 1 in melting points, densities, strength, hardness and reactivity
with oxygen, water and halogens.
Students should be able to exemplify these general properties by
reference to Cr, Mn, Fe, Co, Ni, Cu.
4.1.3.2 Typical properties

development
Many transition elements have ions with different charges, form
coloured compounds and are useful as catalysts.
Students should be able to exemplify these general properties by
reference to compounds of Cr, Mn, Fe, Co, Ni, Cu.
4.2 Bonding, structure, and the properties of matter
Chemists use theories of structure and bonding to explain the physical and chemical properties of
materials. Analysis of structures shows that atoms can be arranged in a variety of ways, some of
which are molecular while others are giant structures. Theories of bonding explain how atoms are held
together in these structures. Scientists use this knowledge of structure and bonding to engineer new
materials with desirable properties. The properties of these materials may offer new applications in a
range of different technologies.
4.2.1 Chemical bonds, ionic, covalent and metallic

4.2.1.1 Chemical bonds
development
There are three types of strong chemical bonds: ionic, covalent and
metallic. For ionic bonding the particles are oppositely charged ions.
For covalent bonding the particles are atoms which share pairs of
electrons. For metallic bonding the particles are atoms which share
delocalised electrons.
Ionic bonding occurs in compounds formed from metals combined
with non-metals.
Covalent bonding occurs in most non-metallic elements and in
compounds of non-metals.
Metallic bonding occurs in metallic elements and alloys.
Students should be able to explain chemical bonding in terms of
electrostatic forces and the transfer or sharing of electrons.
4.2.1.2 Ionic bonding

development
When a metal atom reacts with a non-metal atom electrons in the MS 5b
outer shell of the metal atom are transferred. Metal atoms lose Visualise and represent 2D
electrons to become positively charged ions. Non-metal atoms gain and 3D forms including two-
electrons to become negatively charged ions. The ions produced by dimensional representations
metals in Groups 1 and 2 and by non-metals in Groups 6 and 7 have of 3D objects.
the electronic structure of a noble gas (Group 0).
The electron transfer during the formation of an ionic compound can
be represented by a dot and cross diagram, eg for sodium chloride.

development
Students should be able to draw dot and cross diagrams for ionic WS 1.2
compounds formed by metals in Groups 1 and 2 with non-metals in
Groups 6 and 7.
The charge on the ions produced by metals in Groups 1 and 2 and
by non-metals in Groups 6 and 7 relates to the group number of the
element in the periodic table.
Students should be able to work out the charge on the ions of metals
and non-metals from the group number of the element, limited to the
metals in Groups 1 and 2, and non-metals in Groups 6 and 7.
4.2.1.3 Ionic compounds

development
An ionic compound is a giant structure of ions. Ionic compounds are MS 5b
held together by strong electrostatic forces of attraction between Visualise and represent 2D
oppositely charged ions. These forces act in all directions in the lattice and 3D forms including two-
and this is called ionic bonding. dimensional representations
of 3D objects.
The structure of sodium chloride can be represented in the following
forms:

• deduce that a compound is ionic from a diagram of its structure in
MS 4a
one of the specified forms
• describe the limitations of using dot and cross, ball and stick, two MS 1a, 1c
and three-dimensional diagrams to represent a giant ionic structure
• work out the empirical formula of an ionic compound from a given
model or diagram that shows the ions in the structure.
Students should be familiar with the structure of sodium chloride but
do not need to know the structures of other ionic compounds.
4.2.1.4 Covalent bonding
development
When atoms share pairs of electrons, they form covalent bonds. WS 1.2
These bonds between atoms are strong. Recognise substances as
small molecules, polymers
Covalently bonded substances may consist of small molecules.
or giant structures from
Students should be able to recognise common substances that diagrams showing their
consist of small molecules from their chemical formula. bonding.
Some covalently bonded substances have very large molecules, such

as polymers.
Some covalently bonded substances have giant covalent structures,
such as diamond and silicon dioxide.
The covalent bonds in molecules and giant structures can be
represented in the following forms:
Polymers can be represented in the form:
where n is a large number.

development
Students should be able to: MS 5b
• draw dot and cross diagrams for the molecules of hydrogen,
chlorine, oxygen, nitrogen, hydrogen chloride, water, ammonia and
methane
• represent the covalent bonds in small molecules, in the repeating
units of polymers and in part of giant covalent structures, using a
line to represent a single bond
• describe the limitations of using dot and cross, ball and stick, two
and three-dimensional diagrams to represent molecules or giant
structures
• deduce the molecular formula of a substance from a given model
or diagram in these forms showing the atoms and bonds in the
molecule.
4.2.1.5 Metallic bonding

development
Metals consist of giant structures of atoms arranged in a regular WS 1.2
pattern. Recognise substances as
metallic giant structures
The electrons in the outer shell of metal atoms are delocalised and
from diagrams showing their
so are free to move through the whole structure. The sharing of
bonding.
delocalised electrons gives rise to strong metallic bonds. The bonding
in metals may be represented in the following form: MS 5b
Visualise and represent 2D
of 3D objects.
4.2.2 How bonding and structure are related to the properties of
substances
4.2.2.1 The three states of matter
development
The three states of matter are solid, liquid and gas. Melting and MS 5b
freezing take place at the melting point, boiling and condensing take Visualise and represent 2D
place at the boiling point. and 3D forms including two-
The three states of matter can be represented by a simple model. In
of 3D objects.
this model, particles are represented by small solid spheres. Particle
theory can help to explain melting, boiling, freezing and condensing.
The amount of energy needed to change state from solid to liquid

and from liquid to gas depends on the strength of the forces between
the particles of the substance. The nature of the particles involved
depends on the type of bonding and the structure of the substance.
The stronger the forces between the particles the higher the melting
point and boiling point of the substance.
(HT only) Limitations of the simple model above include that in the
model there are no forces, that all particles are represented as spheres
and that the spheres are solid.
• predict the states of substances at different temperatures given
appropriate data
• explain the different temperatures at which changes of state occur
in terms of energy transfers and types of bonding
• recognise that atoms themselves do not have the bulk properties of
materials
• (HT only) explain the limitations of the particle theory in relation to
changes of state when particles are represented by solid inelastic
spheres which have no forces between them.
4.2.2.2 State symbols

development
In chemical equations, the three states of matter are shown as (s), (l)
and (g), with (aq) for aqueous solutions.
Students should be able to include appropriate state symbols in
chemical equations for the reactions in this specification.
4.2.2.3 Properties of ionic compounds

development
Ionic compounds have regular structures (giant ionic lattices) in which
there are strong electrostatic forces of attraction in all directions
between oppositely charged ions.
These compounds have high melting points and high boiling points
because of the large amounts of energy needed to break the many
strong bonds.
When melted or dissolved in water, ionic compounds conduct
electricity because the ions are free to move and so charge can flow.
Knowledge of the structures of specific ionic compounds other than
sodium chloride is not required.
4.2.2.4 Properties of small molecules

development
Substances that consist of small molecules are usually gases or WS 1.2
liquids that have relatively low melting points and boiling points.
These substances have only weak forces between the molecules
(intermolecular forces). It is these intermolecular forces that are
overcome, not the covalent bonds, when the substance melts or boils.
The intermolecular forces increase with the size of the molecules, so
larger molecules have higher melting and boiling points.
These substances do not conduct electricity because the molecules
do not have an overall electric charge.
Students should be able to use the idea that intermolecular forces are
weak compared with covalent bonds to explain the bulk properties of
molecular substances.
4.2.2.5 Polymers
development
Polymers have very large molecules. The atoms in the polymer
molecules are linked to other atoms by strong covalent bonds. The
intermolecular forces between polymer molecules are relatively strong
and so these substances are solids at room temperature.
Students should be able to recognise polymers from diagrams
showing their bonding and structure.
4.2.2.6 Giant covalent structures
development
Substances that consist of giant covalent structures are solids with MS 5b
very high melting points. All of the atoms in these structures are Visualise and represent 2D
linked to other atoms by strong covalent bonds. These bonds must and 3D forms including two-
be overcome to melt or boil these substances. Diamond and graphite dimensional representations
(forms of carbon) and silicon dioxide (silica) are examples of giant of 3D objects.
covalent structures.
WS 1.2
Students should be able to recognise giant covalent structures from
diagrams showing their bonding and structure.
4.2.2.7 Properties of metals and alloys

development
Metals have giant structures of atoms with strong metallic bonding.
This means that most metals have high melting and boiling points.
In pure metals, atoms are arranged in layers, which allows metals to
be bent and shaped. Pure metals are too soft for many uses and so
are mixed with other metals to make alloys which are harder.
Students should be able to explain why alloys are harder than pure WS 1.2
metals in terms of distortion of the layers of atoms in the structure of a
pure metal.
4.2.2.8 Metals as conductors

development
Metals are good conductors of electricity because the delocalised
electrons in the metal carry electrical charge through the metal. Metals
are good conductors of thermal energy because energy is transferred
by the delocalised electrons.
4.2.3 Structure and bonding of carbon

4.2.3.1 Diamond
development
In diamond, each carbon atom forms four covalent bonds with other MS 5b
carbon atoms in a giant covalent structure, so diamond is very hard, Visualise and represent 2D
has a very high melting point and does not conduct electricity. and 3D forms including two-
of 3D objects.
Students should be able to explain the properties of diamond in terms WS 1.2
of its structure and bonding.
4.2.3.2 Graphite
development
In graphite, each carbon atom forms three covalent bonds with three WS 1.2
other carbon atoms, forming layers of hexagonal rings which have no
covalent bonds between the layers.
In graphite, one electron from each carbon atom is delocalised.
Students should be able to explain the properties of graphite in terms
of its structure and bonding.
Students should know that graphite is similar to metals in that it has
delocalised electrons.
4.2.3.3 Graphene and fullerenes

development
Graphene is a single layer of graphite and has properties that make it WS 1.2, 1.4
useful in electronics and composites. MS 5b
Students should be able to explain the properties of graphene in Visualise and represent 2D
terms of its structure and bonding. and 3D forms including two-
Fullerenes are molecules of carbon atoms with hollow shapes. The of 3D objects.
structure of fullerenes is based on hexagonal rings of carbon atoms
but they may also contain rings with five or seven carbon atoms. The
first fullerene to be discovered was Buckminsterfullerene (C60) which
has a spherical shape.
Carbon nanotubes are cylindrical fullerenes with very high
length to diameter ratios. Their properties make them useful for
nanotechnology, electronics and materials.
• recognise graphene and fullerenes from diagrams and descriptions
of their bonding and structure
• give examples of the uses of fullerenes, including carbon
nanotubes.
4.2.4 Bulk and surface properties of matter including nanoparticles
(chemistry only)
4.2.4.1 Sizes of particles and their properties
development
Nanoscience refers to structures that are 1–100 nm in size, of the WS 1.2, 1.4, 4.1, 4.2, 4.3 4.4,
order of a few hundred atoms. Nanoparticles, are smaller than fine 4.5
particles (PM2.5), which have diameters between 100 and 2500 nm MS 2h
(1 x 10-7 m and 2.5 x 10-6 m). Coarse particles (PM10) have diameters
Make order of magnitude
between 1 x 10-5 m and 2.5 x 10-6 m. Coarse particles are often
calculations.
referred to as dust.
MS 5c
As the side of cube decreases by a factor of 10 the surface area to
volume ratio increases by a factor of 10. Calculate areas of triangles
and rectangles, surface areas
Nanoparticles may have properties different from those for the same and volumes of cubes.
materials in bulk because of their high surface area to volume ratio. It
may also mean that smaller quantities are needed to be effective than
for materials with normal particle sizes.
Students should be able to compare ‘nano’ dimensions to typical MS 1b
dimensions of atoms and molecules. Recognise and use
expressions in standard form.
MS 1c
Use ratios, fractions and
percentages.
MS 1d
Make estimates of the results
of simple calculations.
4.2.4.2 Uses of nanoparticles

development
Nanoparticles have many applications in medicine, in electronics, in
cosmetics and sun creams, as deodorants, and as catalysts. New
applications for nanoparticulate materials are an important area of
research.
Students should consider advantages and disadvantages of the
applications of these nanoparticulate materials, but do not need to
know specific examples or properties other than those specified.
Students should be able to: WS 1.3, 1.4, 1.5
• given appropriate information, evaluate the use of nanoparticles for
a specified purpose
• explain that there are possible risks associated with the use of
nanoparticles.
4.3 Quantitative chemistry

Chemists use quantitative analysis to determine the formulae of compounds and the equations for
reactions. Given this information, analysts can then use quantitative methods to determine the purity of
chemical samples and to monitor the yield from chemical reactions.
Chemical reactions can be classified in various ways. Identifying different types of chemical reaction
allows chemists to make sense of how different chemicals react together, to establish patterns and
to make predictions about the behaviour of other chemicals. Chemical equations provide a means of
representing chemical reactions and are a key way for chemists to communicate chemical ideas.
4.3.1 Chemical measurements, conservation of mass and the quantitative

interpretation of chemical equations
4.3.1.1 Conservation of mass and balanced chemical equations
development
The law of conservation of mass states that no atoms are lost or made WS 1.2
during a chemical reaction so the mass of the products equals the
mass of the reactants.
This means that chemical reactions can be represented by symbol
equations which are balanced in terms of the numbers of atoms of
each element involved on both sides of the equation.
Students should understand the use of the multipliers in equations in
normal script before a formula and in subscript within a formula.
4.3.1.2 Relative formula mass

development
The relative formula mass (Mr) of a compound is the sum of the
relative atomic masses of the atoms in the numbers shown in the
formula.
In a balanced chemical equation, the sum of the relative formula
masses of the reactants in the quantities shown equals the sum of the
relative formula masses of the products in the quantities shown.
4.3.1.3 Mass changes when a reactant or product is a gas
development
Some reactions may appear to involve a change in mass but this can AT 1, 2 ,6
usually be explained because a reactant or product is a gas and its Opportunities within
mass has not been taken into account. For example: when a metal investigation of mass
reacts with oxygen the mass of the oxide produced is greater than the changes using various
mass of the metal or in thermal decompositions of metal carbonates apparatus.
carbon dioxide is produced and escapes into the atmosphere leaving
the metal oxide as the only solid product.
Students should be able to explain any observed changes in mass in
non-enclosed systems during a chemical reaction given the balanced
symbol equation for the reaction and explain these changes in terms
of the particle model.
4.3.1.4 Chemical measurements

development
Whenever a measurement is made there is always some uncertainty WS 3.4
about the result obtained.
• represent the distribution of results and make estimations of
uncertainty
• use the range of a set of measurements about the mean as a
measure of uncertainty.
4.3.2 Use of amount of substance in relation to masses of pure substances

4.3.2.1 Moles (HT only)
development
Chemical amounts are measured in moles. The symbol for the unit WS 4.1, 4.2, 4.3, 4.5, 4.6
mole is mol. MS 1a
The mass of one mole of a substance in grams is numerically equal to Recognise and use
its relative formula mass. expressions in decimal form.
One mole of a substance contains the same number of the stated MS 1b

particles, atoms, molecules or ions as one mole of any other Recognise and use
substance. expressions in standard
form.
The number of atoms, molecules or ions in a mole of a given
substance is the Avogadro constant. The value of the Avogadro MS 2a
constant is 6.02 x 1023 per mole. Use an appropriate number
of significant figures.
Students should understand that the measurement of amounts in
moles can apply to atoms, molecules, ions, electrons, formulae and MS 3a
equations, for example that in one mole of carbon (C) the number of
Understand and use the
atoms is the same as the number of molecules in one mole of carbon
symbols: =, <, <<, >>, >, ∝,
dioxide (CO2).
~
MS 3b
Change the subject of an
equation.
Students should be able to use the relative formula mass of a MS 1c
substance to calculate the number of moles in a given mass of that
substance and vice versa.
4.3.2.2 Amounts of substances in equations (HT only)
development
The masses of reactants and products can be calculated from MS 1a
balanced symbol equations. Recognise and use
expressions in decimal form.
Chemical equations can be interpreted in terms of moles. For
example: MS 1c
Mg + 2HCI MgCI2 + H2 Use ratios, fractions and
percentages.
shows that one mole of magnesium reacts with two moles of
MS 3b
hydrochloric acid to produce one mole of magnesium chloride and
one mole of hydrogen gas. Change the subject of an
equation.
MS 3c
• calculate the masses of substances shown in a balanced symbol
equation Substitute numerical values
into algebraic equations
• calculate the masses of reactants and products from the balanced
using appropriate units for
symbol equation and the mass of a given reactant or product.
physical quantities.
4.3.2.3 Using moles to balance equations (HT only)

development
The balancing numbers in a symbol equation can be calculated from MS 3b
the masses of reactants and products by converting the masses in Change the subject of an
grams to amounts in moles and converting the numbers of moles to equation.
simple whole number ratios.
MS 3c
Students should be able to balance an equation given the masses of
Substitute numerical values
reactants and products.
Students should be able to change the subject of a mathematical using appropriate units for
equation. physical quantities.
4.3.2.4 Limiting reactants (HT only)

development
In a chemical reaction involving two reactants, it is common to use an WS 4.1
excess of one of the reactants to ensure that all of the other reactant
is used. The reactant that is completely used up is called the limiting
reactant because it limits the amount of products.
Students should be able to explain the effect of a limiting quantity of a
reactant on the amount of products it is possible to obtain in terms of
amounts in moles or masses in grams.
4.3.2.5 Concentration of solutions

development
Many chemical reactions take place in solutions. The concentration of MS 1c
a solution can be measured in mass per given volume of solution, eg Use ratios, fractions and
grams per dm3 (g/dm3). percentages.
• calculate the mass of solute in a given volume of solution of known Change the subject of an
concentration in terms of mass per given volume of solution equation.
• (HT only) explain how the mass of a solute and the volume of a
solution is related to the concentration of the solution.
4.3.3 Yield and atom economy of chemical reactions (chemistry only)

4.3.3.1 Percentage yield
development
Even though no atoms are gained or lost in a chemical reaction, it WS 4.2, 4.6
is not always possible to obtain the calculated amount of a product MS 1a
because:
Recognise and use
• the reaction may not go to completion because it is reversible expressions in decimal form.
• some of the product may be lost when it is separated from the
reaction mixture MS 1c
• some of the reactants may react in ways different to the expected Use ratios, fractions and
reaction. percentages.
The amount of a product obtained is known as the yield. When MS 2a

compared with the maximum theoretical amount as a percentage, it is Use an appropriate number
called the percentage yield. of significant figures.
% Yield =
Mass of product actually made
× 100 MS 3b
Maximum theoretical mass of product
Change the subject of an
equation.
• calculate the percentage yield of a product from the actual yield of
a reaction
• (HT only) calculate the theoretical mass of a product from a given
mass of reactant and the balanced equation for the reaction.
4.3.3.2 Atom economy
development
The atom economy (atom utilisation) is a measure of the amount of WS 4.2, 4.6
starting materials that end up as useful products. It is important for MS 1a
sustainable development and for economic reasons to use reactions
Recognise and use
with high atom economy.
The percentage atom economy of a reaction is calculated using the
MS 1c
balanced equation for the reaction as follows:
Relative formula mass of desired product from equation
× 100 percentages.
Sum of relative formula masses of all reactants from equation
MS 3b
Students should be able to: Change the subject of an
• calculate the atom economy of a reaction to form a desired product equation.
from the balanced equation
• (HT only) explain why a particular reaction pathway is chosen to
produce a specified product given appropriate data such as atom
economy (if not calculated), yield, rate, equilibrium position and
usefulness of by-products.
4.3.4 Using concentrations of solutions in mol/dm3 (chemistry only)

(HT only)
development
The concentration of a solution can be measured in mol/dm3. WS 4.2, 4.3, 4.6
MS 1a
The amount in moles of solute or the mass in grams of solute in a
given volume of solution can be calculated from its concentration in Recognise and use
mol/dm3. expressions in decimal form.
If the volumes of two solutions that react completely are known and MS 1c
the concentration of one solution is known, the concentration of the Use ratios, fractions and
other solution can be calculated. percentages.
Students should be able to explain how the concentration of a MS 3b
solution in mol/dm3 is related to the mass of the solute and the volume Change the subject of an
of the solution. equation.
MS 3c
AT 1, 3, 8
Opportunities within
titrations including to
determine concentrations of
strong acids and alkalis.
4.3.5 Use of amount of substance in relation to volumes of gases

(chemistry only) (HT only)
development
Equal amounts in moles of gases occupy the same volume under the WS 1.2, 4.1, 4.2, 4.3, 4.6
same conditions of temperature and pressure. MS 1a
The volume of one mole of any gas at room temperature and pressure Recognise and use
(20oC and 1 atmosphere pressure) is 24 dm3. expressions in decimal form.
The volumes of gaseous reactants and products can be calculated MS 1c

from the balanced equation for the reaction. Use ratios, fractions and
percentages.
• calculate the volume of a gas at room temperature and pressure MS 3b
from its mass and relative formula mass Change the subject of an
• calculate volumes of gaseous reactants and products from a equation.
balanced equation and a given volume of a gaseous reactant or
MS 3c
product
• change the subject of a mathematical equation.
4.4 Chemical changes
Understanding of chemical changes began when people began experimenting with chemical reactions
in a systematic way and organising their results logically. Knowing about these different chemical
changes meant that scientists could begin to predict exactly what new substances would be formed
and use this knowledge to develop a wide range of different materials and processes. It also helped
biochemists to understand the complex reactions that take place in living organisms. The extraction of
important resources from the Earth makes use of the way that some elements and compounds react
with each other and how easily they can be ‘pulled apart’.
4.4.1 Reactivity of metals

4.4.1.1 Metal oxides
development
Metals react with oxygen to produce metal oxides. The reactions are
oxidation reactions because the metals gain oxygen.
Students should be able to explain reduction and oxidation in terms of
loss or gain of oxygen.
4.4.1.2 The reactivity series

development
When metals react with other substances the metal atoms form AT 6
positive ions. The reactivity of a metal is related to its tendency to Mixing of reagents to
form positive ions. Metals can be arranged in order of their reactivity explore chemical changes
in a reactivity series. The metals potassium, sodium, lithium, calcium, and/or products.
magnesium, zinc, iron and copper can be put in order of their
reactivity from their reactions with water and dilute acids.
The non-metals hydrogen and carbon are often included in the
reactivity series.
A more reactive metal can displace a less reactive metal from a
compound.
• recall and describe the reactions, if any, of potassium, sodium,
lithium, calcium, magnesium, zinc, iron and copper with water or
dilute acids and where appropriate, to place these metals in order
of reactivity
• explain how the reactivity of metals with water or dilute acids is
related to the tendency of the metal to form its positive ion
• deduce an order of reactivity of metals based on experimental
results.
The reactions of metals with water and acids are limited to room
temperature and do not include reactions with steam.
4.4.1.3 Extraction of metals and reduction

development
Unreactive metals such as gold are found in the Earth as the metal
itself but most metals are found as compounds that require chemical
reactions to extract the metal.
Metals less reactive than carbon can be extracted from their oxides by
reduction with carbon.
Reduction involves the loss of oxygen.
Knowledge and understanding are limited to the reduction of oxides
using carbon.
Knowledge of the details of processes used in the extraction of metals
is not required.
• interpret or evaluate specific metal extraction processes when
given appropriate information
• identify the substances which are oxidised or reduced in terms of
gain or loss of oxygen.
4.4.1.4 Oxidation and reduction in terms of electrons (HT only)

development
Oxidation is the loss of electrons and reduction is the gain of
electrons.
Student should be able to:
• write ionic equations for displacement reactions
• identify in a given reaction, symbol equation or half equation which
species are oxidised and which are reduced.
4.4.2 Reactions of acids
4.4.2.1 Reactions of acids with metals
development
Acids react with some metals to produce salts and hydrogen.
(HT only) Students should be able to:
• explain in terms of gain or loss of electrons, that these are redox
reactions
• identify which species are oxidised and which are reduced in given
chemical equations.
Knowledge of reactions limited to those of magnesium, zinc and iron
with hydrochloric and sulfuric acids.
4.4.2.2 Neutralisation of acids and salt production

development
Acids are neutralised by alkalis (eg soluble metal hydroxides) and
bases (eg insoluble metal hydroxides and metal oxides) to produce
salts and water, and by metal carbonates to produce salts, water and
carbon dioxide.
The particular salt produced in any reaction between an acid and a
base or alkali depends on:
• the acid used (hydrochloric acid produces chlorides, nitric acid
produces nitrates, sulfuric acid produces sulfates)
• the positive ions in the base, alkali or carbonate.
• predict products from given reactants
• use the formulae of common ions to deduce the formulae of salts.
4.4.2.3 Soluble salts

development
Soluble salts can be made from acids by reacting them with solid
insoluble substances, such as metals, metal oxides, hydroxides or
carbonates. The solid is added to the acid until no more reacts and
the excess solid is filtered off to produce a solution of the salt.
Salt solutions can be crystallised to produce solid salts.
Students should be able to describe how to make pure, dry samples
of named soluble salts from information provided.
Required practical 1: preparation of a pure, dry sample of a soluble salt from an insoluble oxide or
carbonate using a Bunsen burner to heat dilute acid and a water bath or electric heater to evaporate the
solution.
AT skills covered by this practical activity: 2, 3, 4 and 6.
This practical activity also provides opportunities to develop WS and MS. Details of all skills are given in
Key opportunities for skills development.
4.4.2.4 The pH scale and neutralisation

development
Acids produce hydrogen ions (H+) in aqueous solutions. AT 3
This is an opportunity to
Aqueous solutions of alkalis contain hydroxide ions (OH–).
investigate pH changes
The pH scale, from 0 to 14, is a measure of the acidity or alkalinity when a strong acid
of a solution, and can be measured using universal indicator or a pH neutralises a strong alkali.
probe.
A solution with pH 7 is neutral. Aqueous solutions of acids have pH
values of less than 7 and aqueous solutions of alkalis have pH values
greater than 7.
In neutralisation reactions between an acid and an alkali, hydrogen
ions react with hydroxide ions to produce water.
This reaction can be represented by the equation:

• describe the use of universal indicator or a wide range indicator to
measure the approximate pH of a solution
• use the pH scale to identify acidic or alkaline solutions.
4.4.2.5 Titrations (chemistry only)
development
The volumes of acid and alkali solutions that react with each other can
be measured by titration using a suitable indicator.
• describe how to carry out titrations using strong acids and strong
alkalis only (sulfuric, hydrochloric and nitric acids only) to find the
reacting volumes accurately
• (HT Only) calculate the chemical quantities in titrations involving
concentrations in mol/dm3 and in g/dm3.
Required practical 2: (chemistry only) determination of the reacting volumes of solutions of a strong
acid and a strong alkali by titration.
(HT only) determination of the concentration of one of the solutions in mol/dm3 and g/dm3 from the
reacting volumes and the known concentration of the other solution.
AT skills covered by this practical activity: 1 and 8.
Key opportunities and skills development.
4.4.2.6 Strong and weak acids (HT only)

development
A strong acid is completely ionised in aqueous solution. Examples of AT 8
strong acids are hydrochloric, nitric and sulfuric acids. An opportunity to measure
the pH of different acids at
A weak acid is only partially ionised in aqueous solution. Examples of
different concentrations.
weak acids are ethanoic, citric and carbonic acids.
For a given concentration of aqueous solutions, the stronger an acid,
the lower the pH.
As the pH decreases by one unit, the hydrogen ion concentration of
the solution increases by a factor of 10.
• use and explain the terms dilute and concentrated (in terms of
amount of substance), and weak and strong (in terms of the degree
of ionisation) in relation to acids
• describe neutrality and relative acidity in terms of the effect on MS 2h
hydrogen ion concentration and the numerical value of pH (whole Make order of magnitude
numbers only). calculations.
4.4.3 Electrolysis
4.4.3.1 The process of electrolysis
development
When an ionic compound is melted or dissolved in water, the ions
are free to move about within the liquid or solution. These liquids and
solutions are able to conduct electricity and are called electrolytes.
Passing an electric current through electrolytes causes the ions to
move to the electrodes. Positively charged ions move to the negative
electrode (the cathode), and negatively charged ions move to the
positive electrode (the anode). Ions are discharged at the electrodes
producing elements. This process is called electrolysis.
(HT only) Throughout Section 4.4.3 Higher Tier students should
be able to write half equations for the reactions occurring at the
electrodes during electrolysis, and may be required to complete and
balance supplied half equations.
4.4.3.2 Electrolysis of molten ionic compounds

development
When a simple ionic compound (eg lead bromide) is electrolysed in A safer alternative for
the molten state using inert electrodes, the metal (lead) is produced at practical work is anhydrous
the cathode and the non-metal (bromine) is produced at the anode. zinc chloride.
Students should be able to predict the products of the electrolysis of
binary ionic compounds in the molten state.
4.4.3.3 Using electrolysis to extract metals

development
Metals can be extracted from molten compounds using electrolysis.
Electrolysis is used if the metal is too reactive to be extracted by
reduction with carbon or if the metal reacts with carbon. Large
amounts of energy are used in the extraction process to melt the
compounds and to produce the electrical current.
Aluminium is manufactured by the electrolysis of a molten mixture of
aluminium oxide and cryolite using carbon as the positive electrode
(anode).
• explain why a mixture is used as the electrolyte
• explain why the positive electrode must be continually replaced.
4.4.3.4 Electrolysis of aqueous solutions
development
The ions discharged when an aqueous solution is electrolysed using
inert electrodes depend on the relative reactivity of the elements
involved.
At the negative electrode (cathode), hydrogen is produced if the metal
is more reactive than hydrogen.
At the positive electrode (anode), oxygen is produced unless the
solution contains halide ions when the halogen is produced.
This happens because in the aqueous solution water molecules
break down producing hydrogen ions and hydroxide ions that are
discharged.
Students should be able to predict the products of the electrolysis of WS 1.2
aqueous solutions containing a single ionic compound.
Required practical 3: investigate what happens when aqueous solutions are electrolysed using inert
electrodes. This should be an investigation involving developing a hypothesis.
AT skills covered by this practical activity: 3, 7 and 8.
4.4.3.5 Representation of reactions at electrodes as half equations (HT only)

development
During electrolysis, at the cathode (negative electrode), positively
charged ions gain electrons and so the reactions are reductions.
At the anode (positive electrode), negatively charged ions lose
electrons and so the reactions are oxidations.
Reactions at electrodes can be represented by half equations, for
example:
2H+ + 2e- → H2
and
4OH- → O2 + 2H2O + 4e-
or
4OH- – 4e- → O2 + 2H2O
4.5 Energy changes

Energy changes are an important part of chemical reactions. The interaction of particles often involves
transfers of energy due to the breaking and formation of bonds. Reactions in which energy is released
to the surroundings are exothermic reactions, while those that take in thermal energy are endothermic.
These interactions between particles can produce heating or cooling effects that are used in a range
of everyday applications. Some interactions between ions in an electrolyte result in the production of
electricity. Cells and batteries use these chemical reactions to provide electricity. Electricity can also
be used to decompose ionic substances and is a useful means of producing elements that are too
expensive to extract any other way.
4.5.1 Exothermic and endothermic reactions

4.5.1.1 Energy transfer during exothermic and endothermic reactions
Content Key opportunities for
skills development
Energy is conserved in chemical reactions. The amount of energy in the AT 5
universe at the end of a chemical reaction is the same as before the An opportunity to measure
reaction takes place. If a reaction transfers energy to the surroundings temperature changes
the product molecules must have less energy than the reactants, by when substances react or
the amount transferred. dissolve in water.
An exothermic reaction is one that transfers energy to the surroundings
so the temperature of the surroundings increases.
Exothermic reactions include combustion, many oxidation reactions
and neutralisation.
Everyday uses of exothermic reactions include self-heating cans and
hand warmers.
An endothermic reaction is one that takes in energy from the
surroundings so the temperature of the surroundings decreases.
Endothermic reactions include thermal decompositions and the
reaction of citric acid and sodium hydrogencarbonate. Some sports
injury packs are based on endothermic reactions.
• distinguish between exothermic and endothermic reactions on the
basis of the temperature change of the surroundings
• evaluate uses and applications of exothermic and endothermic
reactions given appropriate information.
Limited to measurement of temperature change. Calculation of energy
changes or ΔH is not required.
Required practical 4: investigate the variables that affect temperature changes in reacting solutions
such as, eg acid plus metals, acid plus carbonates, neutralisations, displacement of metals.
4.5.1.2 Reaction profiles
development
Chemical reactions can occur only when reacting particles collide with
each other and with sufficient energy. The minimum amount of energy
that particles must have to react is called the activation energy.
Reaction profiles can be used to show the relative energies of
reactants and products, the activation energy and the overall energy
change of a reaction.
• draw simple reaction profiles (energy level diagrams) for exothermic
and endothermic reactions showing the relative energies of
reactants and products, the activation energy and the overall
energy change, with a curved line to show the energy as the
reaction proceeds
• use reaction profiles to identify reactions as exothermic or
endothermic
• explain that the activation energy is the energy needed for a
reaction to occur.
4.5.1.3 The energy change of reactions (HT only)

development
During a chemical reaction:
• energy must be supplied to break bonds in the reactants
• energy is released when bonds in the products are formed.
The energy needed to break bonds and the energy released when
bonds are formed can be calculated from bond energies.
The difference between the sum of the energy needed to break bonds
in the reactants and the sum of the energy released when bonds in the
products are formed is the overall energy change of the reaction.
In an exothermic reaction, the energy released from forming new
bonds is greater than the energy needed to break existing bonds.
In an endothermic reaction, the energy needed to break existing
bonds is greater than the energy released from forming new bonds.
Students should be able to calculate the energy transferred in MS 1a
chemical reactions using bond energies supplied.
4.5.2 Chemical cells and fuel cells (chemistry only)

4.5.2.1 Cells and batteries
development
Cells contain chemicals which react to produce electricity. AT6
Safe and careful use of
The voltage produced by a cell is dependent upon a number of factors
liquids.
including the type of electrode and electrolyte.
A simple cell can be made by connecting two different metals in
contact with an electrolyte.
Batteries consist of two or more cells connected together in series to
provide a greater voltage.
In non-rechargeable cells and batteries the chemical reactions stop
when one of the reactants has been used up. Alkaline batteries are
non-rechargeable.
Rechargeable cells and batteries can be recharged because the
chemical reactions are reversed when an external electrical current is
supplied.
Students should be able to interpret data for relative reactivity of
different metals and evaluate the use of cells.
Students do not need to know details of cells and batteries other than
those specified.
4.5.2.2 Fuel cells

development
Fuel cells are supplied by an external source of fuel (eg hydrogen) and
oxygen or air. The fuel is oxidised electrochemically within the fuel cell
to produce a potential difference.
The overall reaction in a hydrogen fuel cell involves the oxidation of
hydrogen to produce water.
Hydrogen fuel cells offer a potential alternative to rechargeable cells
and batteries.
• evaluate the use of hydrogen fuel cells in comparison with
rechargeable cells and batteries
• (HT only) write the half equations for the electrode reactions in the
hydrogen fuel cell.
4.6 The rate and extent of chemical change
Chemical reactions can occur at vastly different rates. Whilst the reactivity of chemicals is a significant
factor in how fast chemical reactions proceed, there are many variables that can be manipulated in
order to speed them up or slow them down. Chemical reactions may also be reversible and therefore
the effect of different variables needs to be established in order to identify how to maximise the yield of
desired product. Understanding energy changes that accompany chemical reactions is important for
this process. In industry, chemists and chemical engineers determine the effect of different variables
on reaction rate and yield of product. Whilst there may be compromises to be made, they carry out
optimisation processes to ensure that enough product is produced within a sufficient time, and in an
energy-efficient way.
4.6.1 Rate of reaction

4.6.1.1 Calculating rates of reactions
development
The rate of a chemical reaction can be found by measuring the MS 1a
quantity of a reactant used or the quantity of product formed over Recognise and use
time: expressions in decimal form.
quantity of reactant used
mean rate of reaction = time taken MS 1c
quantity of product formed percentages.
mean rate of reaction = time taken
MS 1d
The quantity of reactant or product can be measured by the mass in Make estimates of
grams or by a volume in cm3. the results of simple
calculations.
The units of rate of reaction may be given as g/s or cm3/s.
MS 4a
For the Higher Tier, students are also required to use quantity of
reactants in terms of moles and units for rate of reaction in mol/s. Translate information
between graphical and
Students should be able to: numeric form.
• calculate the mean rate of a reaction from given information about
MS 4b
the quantity of a reactant used or the quantity of a product formed
and the time taken Drawing and interpreting
appropriate graphs from
• draw, and interpret, graphs showing the quantity of product formed
data to determine rate of
or quantity of reactant used up against time
reaction.
• draw tangents to the curves on these graphs and use the slope of
the tangent as a measure of the rate of reaction MS 4c
• (HT only) calculate the gradient of a tangent to the curve on these Plot two variables from
graphs as a measure of rate of reaction at a specific time. experimental or other data.
MS 4d
Determine the slope and
intercept of a linear graph.
MS 4e
Draw and use the slope of
a tangent to a curve as a
measure of rate of change.
4.6.1.2 Factors which affect the rates of chemical reactions

development
Factors which affect the rates of chemical reactions include: the
concentrations of reactants in solution, the pressure of reacting gases,
the surface area of solid reactants, the temperature and the presence
of catalysts.
Students should be able to recall how changing these factors affects This topic offers
the rate of chemical reactions. opportunities for practical
work and investigations in
addition to required
practical 5.
Required practical 5: investigate how changes in concentration affect the rates of reactions by a
method involving measuring the volume of a gas produced and a method involving a change in colour
or turbidity.
This should be an investigation involving developing a hypothesis.
4.6.1.3 Collision theory and activation energy

development
Collision theory explains how various factors affect rates of reactions.
According to this theory, chemical reactions can occur only when
reacting particles collide with each other and with sufficient energy.
The minimum amount of energy that particles must have to react is
called the activation energy.
Increasing the concentration of reactants in solution, the pressure of
reacting gases, and the surface area of solid reactants increases the
frequency of collisions and so increases the rate of reaction.
Increasing the temperature increases the frequency of collisions and
makes the collisions more energetic, and so increases the rate of
reaction.
Students should be able to : WS 1.2
• predict and explain using collision theory the effects of changing
conditions of concentration, pressure and temperature on the rate
of a reaction
• predict and explain the effects of changes in the size of pieces of a MS 5c
reacting solid in terms of surface area to volume ratio MS 1c
• use simple ideas about proportionality when using collision theory
to explain the effect of a factor on the rate of a reaction.
4.6.1.4 Catalysts
development
Catalysts change the rate of chemical reactions but are not used AT 5
up during the reaction. Different reactions need different catalysts. An opportunity to investigate
Enzymes act as catalysts in biological systems. the catalytic effect of
adding different metal salts
Catalysts increase the rate of reaction by providing a different
to a reaction such as the
pathway for the reaction that has a lower activation energy.
decomposition of hydrogen
A reaction profile for a catalysed reaction can be drawn in the peroxide.
following form:
Students should be able to identify catalysts in reactions from their

effect on the rate of reaction and because they are not included in the
chemical equation for the reaction.
Students should be able to explain catalytic action in terms of
activation energy.
Students do not need to know the names of catalysts other than
those specified in the subject content.
4.6.2 Reversible reactions and dynamic equilibrium

4.6.2.1 Reversible reactions
development
In some chemical reactions, the products of the reaction can react to
produce the original reactants. Such reactions are called reversible
reactions and are represented:
A + B C + D
The direction of reversible reactions can be changed by changing the

conditions.
For example:
4.6.2.2 Energy changes and reversible reactions

development
If a reversible reaction is exothermic in one direction, it is endothermic
in the opposite direction. The same amount of energy is transferred in
each case. For example:
4.6.2.3 Equilibrium
development
When a reversible reaction occurs in apparatus which prevents the WS 1.2
escape of reactants and products, equilibrium is reached when the
forward and reverse reactions occur at exactly the same rate.
4.6.2.4 The effect of changing conditions on equilibrium (HT only)
development
The relative amounts of all the reactants and products at equilibrium
depend on the conditions of the reaction.
If a system is at equilibrium and a change is made to any of the
conditions, then the system responds to counteract the change.
The effects of changing conditions on a system at equilibrium can be
predicted using Le Chatelier’s Principle.
Students should be able to make qualitative predictions about the
effect of changes on systems at equilibrium when given appropriate
information.
4.6.2.5 The effect of changing concentration (HT only)

development
If the concentration of one of the reactants or products is changed,
the system is no longer at equilibrium and the concentrations of all the
substances will change until equilibrium is reached again.
If the concentration of a reactant is increased, more products will be
formed until equilibrium is reached again.
If the concentration of a product is decreased, more reactants will
react until equilibrium is reached again.
Students should be able to interpret appropriate given data to predict
the effect of a change in concentration of a reactant or product on
given reactions at equilibrium.
4.6.2.6 The effect of temperature changes on equilibrium (HT only)

development
If the temperature of a system at equilibrium is increased:
• the relative amount of products at equilibrium increases for an
endothermic reaction
• the relative amount of products at equilibrium decreases for an
exothermic reaction.
If the temperature of a system at equilibrium is decreased:
• the relative amount of products at equilibrium decreases for an
endothermic reaction
• the relative amount of products at equilibrium increases for an
exothermic reaction.
Students should be able to interpret appropriate given data to
predict the effect of a change in temperature on given reactions at
equilibrium.
4.6.2.7 The effect of pressure changes on equilibrium (HT only)

development
For gaseous reactions at equilibrium:
• an increase in pressure causes the equilibrium position to shift
towards the side with the smaller number of molecules as shown
by the symbol equation for that reaction
• a decrease in pressure causes the equilibrium position to shift
towards the side with the larger number of molecules as shown by
the symbol equation for that reaction.
Students should be able to interpret appropriate given data to predict
the effect of pressure changes on given reactions at equilibrium.
4.7 Organic chemistry
The chemistry of carbon compounds is so important that it forms a separate branch of chemistry. A
great variety of carbon compounds is possible because carbon atoms can form chains and rings linked
by C-C bonds. This branch of chemistry gets its name from the fact that the main sources of organic
compounds are living, or once-living materials from plants and animals. These sources include fossil
fuels which are a major source of feedstock for the petrochemical industry. Chemists are able to take
organic molecules and modify them in many ways to make new and useful materials such as polymers,
pharmaceuticals, perfumes and flavourings, dyes and detergents.
4.7.1 Carbon compounds as fuels and feedstock

4.7.1.1 Crude oil, hydrocarbons and alkanes
development
Crude oil is a finite resource found in rocks. Crude oil is the remains of WS 1.2
an ancient biomass consisting mainly of plankton that was buried in Make models of alkane
mud. molecules using the
molecular modelling kits.
Crude oil is a mixture of a very large number of compounds. Most of
the compounds in crude oil are hydrocarbons, which are molecules
made up of hydrogen and carbon atoms only.
Most of the hydrocarbons in crude oil are hydrocarbons called
alkanes. The general formula for the homologous series of alkanes is
CnH2n+2
The first four members of the alkanes are methane, ethane, propane
and butane.
Alkane molecules can be represented in the following forms:
C2H6 or
Students should be able to recognise substances as alkanes given

their formulae in these forms.
Students do not need to know the names of specific alkanes other
than methane, ethane, propane and butane.
4.7.1.2 Fractional distillation and petrochemicals

development
The many hydrocarbons in crude oil may be separated into fractions, WS 1.2
each of which contains molecules with a similar number of carbon
atoms, by fractional distillation.
The fractions can be processed to produce fuels and feedstock for
the petrochemical industry.
Many of the fuels on which we depend for our modern lifestyle, such
as petrol, diesel oil, kerosene, heavy fuel oil and liquefied petroleum
gases, are produced from crude oil.
Many useful materials on which modern life depends are produced
by the petrochemical industry, such as solvents, lubricants, polymers,
detergents.
The vast array of natural and synthetic carbon compounds occur due
to the ability of carbon atoms to form families of similar compounds.
Students should be able to explain how fractional distillation works in
terms of evaporation and condensation.
Knowledge of the names of other specific fractions or fuels is not
required.
4.7.1.3 Properties of hydrocarbons

development
Some properties of hydrocarbons depend on the size of their WS 1.2, 4.1
molecules, including boiling point, viscosity and flammability. These Investigate the properties of
properties influence how hydrocarbons are used as fuels. different hydrocarbons.
Students should be able to recall how boiling point, viscosity and
flammability change with increasing molecular size.
The combustion of hydrocarbon fuels releases energy. During
combustion, the carbon and hydrogen in the fuels are oxidised. The
complete combustion of a hydrocarbon produces carbon dioxide and
water.
Students should be able to write balanced equations for the complete
combustion of hydrocarbons with a given formula.
Knowledge of trends in properties of hydrocarbons is limited to:
• boiling points
• viscosity
• flammability.
4.7.1.4 Cracking and alkenes
development
Hydrocarbons can be broken down (cracked) to produce smaller, WS 1.2
more useful molecules.
Cracking can be done by various methods including catalytic cracking
and steam cracking.
Students should be able to describe in general terms the conditions
used for catalytic cracking and steam cracking.
The products of cracking include alkanes and another type of
hydrocarbon called alkenes.
Alkenes are more reactive than alkanes and react with bromine water,
which is used as a test for alkenes.
Students should be able to recall the colour change when bromine
water reacts with an alkene.
There is a high demand for fuels with small molecules and so some of
the products of cracking are useful as fuels.
Alkenes are used to produce polymers and as starting materials for
the production of many other chemicals.
Students should be able to balance chemical equations as examples
of cracking given the formulae of the reactants and products.
Students should be able to give examples to illustrate the usefulness
of cracking. They should also be able to explain how modern life
depends on the uses of hydrocarbons.
(For Combined Science: Trilogy and Synergy students do not need to
know the formulae or names of individual alkenes.)
4.7.2 Reactions of alkenes and alcohols (chemistry only)

4.7.2.1 Structure and formulae of alkenes
development
Alkenes are hydrocarbons with a double carbon-carbon bond. The WS 1.2
general formula for the homologous series of alkenes is CnH2n Recognise substances that
are alkenes from their names
Alkene molecules are unsaturated because they contain two fewer
or from given formulae in
hydrogen atoms than the alkane with the same number of carbon
these forms.
atoms.
MS 5b
The first four members of the homologous series of alkenes are
ethene, propene, butene and pentene. Visualise and represent 2D
Alkene molecules can be represented in the following forms: dimensional representations
of 3D objects.
C3H6
or
Students do not need to know the names of individual alkenes other

than ethene, propene, butene and pentene.
4.7.2.2 Reactions of alkenes

development
Alkenes are hydrocarbons with the functional group C=C.
It is the generality of reactions of functional groups that determine the
reactions of organic compounds.
Alkenes react with oxygen in combustion reactions in the same way
as other hydrocarbons, but they tend to burn in air with smoky flames
because of incomplete combustion.
Alkenes react with hydrogen, water and the halogens, by the addition
of atoms across the carbon-carbon double bond so that the double
bond becomes a single carbon-carbon bond.
• describe the reactions and conditions for the addition of hydrogen,
water and halogens to alkenes
• draw fully displayed structural formulae of the first four members
of the alkenes and the products of their addition reactions with
hydrogen, water, chlorine, bromine and iodine.
4.7.2.3 Alcohols
development
Alcohols contain the functional group –OH. AT 2, 5, 6
Opportunities when
Methanol, ethanol, propanol and butanol are the first four members of
investigating reactions of
a homologous series of alcohols.
alcohols.
Alcohols can be represented in the following forms:
CH3CH2OH
or

• describe what happens when any of the first four alcohols react
with sodium, burn in air, are added to water, react with an oxidising
agent
• recall the main uses of these alcohols.
Aqueous solutions of ethanol are produced when sugar solutions are
fermented using yeast.
Students should know the conditions used for fermentation of sugar
using yeast.
Students should be able to recognise alcohols from their names or
from given formulae.
Students do not need to know the names of individual alcohols other
than methanol, ethanol, propanol and butanol.
Students are not expected to write balanced chemical equations for
the reactions of alcohols other than for combustion reactions.
4.7.2.4 Carboxylic acids

development
Carboxylic acids have the functional group –COOH. AT 2, 5, 6
Opportunities within
The first four members of a homologous series of carboxylic acids are
investigation of the reactions
methanoic acid, ethanoic acid, propanoic acid and butanoic acid.
of carboxylic acids.
The structures of carboxylic acids can be represented in the following
forms:
CH3COOH
or

• describe what happens when any of the first four carboxylic acids
react with carbonates, dissolve in water, react with alcohols
• (HT only) explain why carboxylic acids are weak acids in terms of
ionisation and pH (see Strong and weak acids (HT only)).
Students should be able to recognise carboxylic acids from their
names or from given formulae.
Students do not need to know the names of individual carboxylic
acids other than methanoic acid, ethanoic acid, propanoic acid and
butanoic acid.
Students are not expected to write balanced chemical equations for
the reactions of carboxylic acids.
Students do not need to know the names of esters other than ethyl
ethanoate.
4.7.3 Synthetic and naturally occurring polymers (chemistry only)
4.7.3.1 Addition polymerisation
development
Alkenes can be used to make polymers such as poly(ethene) and WS 1.2
poly(propene) by addition polymerisation. Use models to represent
addition polymerisation.
In addition polymerisation reactions, many small molecules
(monomers) join together to form very large molecules (polymers).
For example:
In addition polymers the repeating unit has the same atoms as the
monomer because no other molecule is formed in the reaction.
• recognise addition polymers and monomers from diagrams in the Visualise and represent 2D
forms shown and from the presence of the functional group C=C in and 3D forms including two-
the monomers dimensional representations
• draw diagrams to represent the formation of a polymer from a of 3D objects.
given alkene monomer
• relate the repeating unit to the monomer.
4.7.3.2 Condensation polymerisation (HT only)

development
Condensation polymerisation involves monomers with two functional WS 1.2
groups. When these types of monomers react they join together, Use models to
usually losing small molecules such as water, and so the reactions are represent condensation
called condensation reactions. polymerisation.
The simplest polymers are produced from two different monomers
with two of the same functional groups on each monomer.
For example:
ethane diol
and
hexanedioic acid
polymerise to produce a polyester:
Students should be able to explain the basic principles of MS 5b

condensation polymerisation by reference to the functional groups in Visualise and represent 2D
the monomers and the repeating units in the polymers. and 3D forms including two-
of 3D objects.
4.7.3.3 Amino acids (HT only)

development
Amino acids have two different functional groups in a molecule. Amino
acids react by condensation polymerisation to produce polypeptides.
For example: glycine is H2NCH2COOH and polymerises to produce
the polypeptide
(-HNCH2COO-)n and n H2O
Different amino acids can be combined in the same chain to produce
proteins.
4.7.3.4 DNA (deoxyribonucleic acid) and other naturally occurring polymers
development
DNA (deoxyribonucleic acid) is a large molecule essential for life. DNA
encodes genetic instructions for the development and functioning of
living organisms and viruses.
Most DNA molecules are two polymer chains, made from four different
monomers called nucleotides, in the form of a double helix. Other
naturally occurring polymers important for life include proteins, starch
and cellulose.
Students should be able to name the types of monomers from which
these naturally occurring polymers are made.
4.8 Chemical analysis

Analysts have developed a range of qualitative tests to detect specific chemicals. The tests are based
on reactions that produce a gas with distinctive properties, or a colour change or an insoluble solid that
appears as a precipitate.
Instrumental methods provide fast, sensitive and accurate means of analysing chemicals, and are
particularly useful when the amount of chemical being analysed is small. Forensic scientists and drug
control scientists rely on such instrumental methods in their work.
4.8.1 Purity, formulations and chromatography

4.8.1.1 Pure substances
development
In chemistry, a pure substance is a single element or compound, not WS 2.2, 4.1
mixed with any other substance.
Pure elements and compounds melt and boil at specific temperatures.
Melting point and boiling point data can be used to distinguish pure
substances from mixtures.
In everyday language, a pure substance can mean a substance that
has had nothing added to it, so it is unadulterated and in its natural
state, eg pure milk.
Students should be able to use melting point and boiling point data to
distinguish pure from impure substances.
4.8.1.2 Formulations
development
A formulation is a mixture that has been designed as a useful product. WS 1.4, 2.2
Many products are complex mixtures in which each chemical has a
particular purpose. Formulations are made by mixing the components
in carefully measured quantities to ensure that the product has the
required properties. Formulations include fuels, cleaning agents,
paints, medicines, alloys, fertilisers and foods.
Students should be able to identify formulations given appropriate
information.
Students do not need to know the names of components in
proprietary products.
4.8.1.3 Chromatography
development
Chromatography can be used to separate mixtures and can give WS 2.2, 3.1, 2, 3
information to help identify substances. Chromatography involves MS 1a
a stationary phase and a mobile phase. Separation depends on the
Recognise and use
distribution of substances between the phases.
The ratio of the distance moved by a compound (centre of spot from
MS 1c
origin) to the distance moved by the solvent can be expressed as its
Rf value: Use ratios, fractions and
percentages.
distance moved by substance
Rf = distance moved by solvent MS 1d
Make estimates of
Different compounds have different Rf values in different solvents, the results of simple
which can be used to help identify the compounds. The compounds calculations.
in a mixture may separate into different spots depending on the
solvent but a pure compound will produce a single spot in all solvents.
• explain how paper chromatography separates mixtures
• suggest how chromatographic methods can be used for
distinguishing pure substances from impure substances
• interpret chromatograms and determine Rf values from
chromatograms
• provide answers to an appropriate number of significant figures. MS 2a
Required practical 6: investigate how paper chromatography can be used to separate and tell the
difference between coloured substances. Students should calculate Rf values.
4.8.2 Identification of common gases

4.8.2.1 Test for hydrogen
development
The test for hydrogen uses a burning splint held at the open end of a
test tube of the gas. Hydrogen burns rapidly with a pop sound.
4.8.2.2 Test for oxygen

development
The test for oxygen uses a glowing splint inserted into a test tube of
the gas. The splint relights in oxygen.
4.8.2.3 Test for carbon dioxide

development
The test for carbon dioxide uses an aqueous solution of calcium
hydroxide (lime water). When carbon dioxide is shaken with or
bubbled through limewater the limewater turns milky (cloudy).
4.8.2.4 Test for chlorine

development
The test for chlorine uses litmus paper. When damp litmus paper is
put into chlorine gas the litmus paper is bleached and turns white.
4.8.3 Identification of ions by chemical and spectroscopic means

(chemistry only)
4.8.3.1 Flame tests
development
Flame tests can be used to identify some metal ions (cations). AT 8
Lithium, sodium, potassium, calcium and copper compounds produce An opportunity to investigate
distinctive colours in flame tests: flame colours.
• lithium compounds result in a crimson flame
• sodium compounds result in a yellow flame
• potassium compounds result in a lilac flame
• calcium compounds result in an orange-red flame
• copper compounds result in a green flame.
If a sample containing a mixture of ions is used some flame colours
can be masked.
Students should be able to identify species from the results of the WS 2.2
tests in 4.8.3.1 to 4.8.3.5.
Flame colours of other metal ions are not required knowledge.
4.8.3.2 Metal hydroxides
development
Sodium hydroxide solution can be used to identify some metal ions AT 8
(cations). An opportunity to make
precipitates of metal
Solutions of aluminium, calcium and magnesium ions form white
hydroxides.
precipitates when sodium hydroxide solution is added but only the
aluminium hydroxide precipitate dissolves in excess sodium hydroxide
solution.
Solutions of copper(II), iron(II) and iron(III) ions form coloured
precipitates when sodium hydroxide solution is added.
Copper(II) forms a blue precipitate, iron(II) a green precipitate and
iron(III) a brown precipitate.
Students should be able to write balanced equations for the reactions WS 2.2
to produce the insoluble hydroxides.
Students are not expected to write equations for the production of
sodium aluminate.
4.8.3.3 Carbonates
development
Carbonates react with dilute acids to form carbon dioxide gas. Carbon
dioxide can be identified with limewater.
4.8.3.4 Halides
development
Halide ions in solution produce precipitates with silver nitrate solution
in the presence of dilute nitric acid. Silver chloride is white, silver
bromide is cream and silver iodide is yellow.
4.8.3.5 Sulfates
development
Sulfate ions in solution produce a white precipitate with barium
chloride solution in the presence of dilute hydrochloric acid.
Required practical 7: use of chemical tests to identify the ions in unknown single ionic compounds
covering the ions from sections Flame tests to Sulfates.
4.8.3.6 Instrumental methods

development
Elements and compounds can be detected and identified using
instrumental methods. Instrumental methods are accurate, sensitive
and rapid.
Students should be able to state advantages of instrumental methods
compared with the chemical tests in this specification.
4.8.3.7 Flame emission spectroscopy

development
Flame emission spectroscopy is an example of an instrumental AT 8
method used to analyse metal ions in solutions. An opportunity to observe
flame spectra using a
The sample is put into a flame and the light given out is passed
hand-held spectroscope.
through a spectroscope. The output is a line spectrum that can be
analysed to identify the metal ions in the solution and measure their
concentrations.
Students should be able to interpret an instrumental result given WS 3.6
appropriate data in chart or tabular form, when accompanied MS 4a
by a reference set in the same form, limited to flame emission
spectroscopy.
4.9 Chemistry of the atmosphere
The Earth’s atmosphere is dynamic and forever changing. The causes of these changes are sometimes
man-made and sometimes part of many natural cycles. Scientists use very complex software to predict
weather and climate change as there are many variables that can influence this. The problems caused
by increased levels of air pollutants require scientists and engineers to develop solutions that help to
reduce the impact of human activity.
4.9.1 The composition and evolution of the Earth's atmosphere

4.9.1.1 The proportions of different gases in the atmosphere
development
For 200 million years, the proportions of different gases in the MS 1c
atmosphere have been much the same as they are today: To use ratios, fractions and
• about four-fifths (approximately 80 %) nitrogen percentages.
• about one-fifth (approximately 20 %) oxygen
• small proportions of various other gases, including carbon dioxide,
water vapour and noble gases.
4.9.1.2 The Earth's early atmosphere

development
Theories about what was in the Earth’s early atmosphere and how WS 1.1, 1.2, 1.3, 3.5, 3.6,
the atmosphere was formed have changed and developed over time. 4.1
Evidence for the early atmosphere is limited because of the time scale
of 4.6 billion years.
One theory suggests that during the first billion years of the Earth’s
existence there was intense volcanic activity that released gases that
formed the early atmosphere and water vapour that condensed to
form the oceans. At the start of this period the Earth’s atmosphere
may have been like the atmospheres of Mars and Venus today,
consisting of mainly carbon dioxide with little or no oxygen gas.
Volcanoes also produced nitrogen which gradually built up in the
atmosphere and there may have been small proportions of methane
and ammonia.
When the oceans formed carbon dioxide dissolved in the water and
carbonates were precipitated producing sediments, reducing the
amount of carbon dioxide in the atmosphere. No knowledge of other
theories is required.
Students should be able to, given appropriate information, interpret
evidence and evaluate different theories about the Earth’s early
atmosphere.
4.9.1.3 How oxygen increased

development
Algae and plants produced the oxygen that is now in the atmosphere WS 1.2
by photosynthesis, which can be represented by the equation: An opportunity to show
that aquatic plants produce
oxygen in daylight.
Algae first produced oxygen about 2.7 billion years ago and soon after
this oxygen appeared in the atmosphere. Over the next billion years
plants evolved and the percentage of oxygen gradually increased to a
level that enabled animals to evolve.
4.9.1.4 How carbon dioxide decreased

development
Algae and plants decreased the percentage of carbon dioxide in the
atmosphere by photosynthesis.
Carbon dioxide was also decreased by the formation of sedimentary
rocks and fossil fuels that contain carbon.
Students should be able to: WS 1.2, 4.1
• describe the main changes in the atmosphere over time and some
of the likely causes of these changes
• describe and explain the formation of deposits of limestone, coal,
crude oil and natural gas.
4.9.2 Carbon dioxide and methane as greenhouse gases

4.9.2.1 Greenhouse gases
development
Greenhouse gases in the atmosphere maintain temperatures on WS 1.2
Earth high enough to support life. Water vapour, carbon dioxide and
methane are greenhouse gases.
Students should be able to describe the greenhouse effect in terms of
the interaction of short and long wavelength radiation with matter.
4.9.2.2 Human activities which contribute to an increase in greenhouse gases in the
atmosphere
development
Some human activities increase the amounts of greenhouse gases in
the atmosphere. These include:
• carbon dioxide
• methane.
Students should be able to recall two human activities that increase
the amounts of each of the greenhouse gases carbon dioxide and
methane.
Based on peer-reviewed evidence, many scientists believe that
human activities will cause the temperature of the Earth’s atmosphere
to increase at the surface and that this will result in global climate
change.
However, it is difficult to model such complex systems as global
climate change. This leads to simplified models, speculation and
opinions presented in the media that may be based on only parts of
the evidence and which may be biased.
Students should be able to: WS 1.2, 1.3, 1.6
• evaluate the quality of evidence in a report about global climate
change given appropriate information
• describe uncertainties in the evidence base
• recognise the importance of peer review of results and of
communicating results to a wide range of audiences.
4.9.2.3 Global climate change

development
An increase in average global temperature is a major cause of climate WS 1.5
change.
There are several potential effects of global climate change.
• describe briefly four potential effects of global climate change
• discuss the scale, risk and environmental implications of global
climate change.
4.9.2.4 The carbon footprint and its reduction

development
The carbon footprint is the total amount of carbon dioxide and other WS 1.3
greenhouse gases emitted over the full life cycle of a product, service
or event.
The carbon footprint can be reduced by reducing emissions of carbon
dioxide and methane.
• describe actions to reduce emissions of carbon dioxide and
methane
• give reasons why actions may be limited.
4.9.3 Common atmospheric pollutants and their sources

4.9.3.1 Atmospheric pollutants from fuels
development
The combustion of fuels is a major source of atmospheric pollutants.
Most fuels, including coal, contain carbon and/or hydrogen and may
also contain some sulfur.
The gases released into the atmosphere when a fuel is burned may
include carbon dioxide, water vapour, carbon monoxide, sulfur dioxide
and oxides of nitrogen. Solid particles and unburned hydrocarbons
may also be released that form particulates in the atmosphere.
• describe how carbon monoxide, soot (carbon particles), sulfur
dioxide and oxides of nitrogen are produced by burning fuels
• predict the products of combustion of a fuel given appropriate WS 1.2
information about the composition of the fuel and the conditions in
which it is used.
4.9.3.2 Properties and effects of atmospheric pollutants

development
Carbon monoxide is a toxic gas. It is colourless and odourless and so
is not easily detected.
Sulfur dioxide and oxides of nitrogen cause respiratory problems in
humans and cause acid rain.
Particulates cause global dimming and health problems for humans.
Students should be able to describe and explain the problems caused WS 1.4
by increased amounts of these pollutants in the air.
4.10 Using resources
Industries use the Earth’s natural resources to manufacture useful products. In order to operate
sustainably, chemists seek to minimise the use of limited resources, use of energy, waste and
environmental impact in the manufacture of these products. Chemists also aim to develop ways of
disposing of products at the end of their useful life in ways that ensure that materials and stored energy
are utilised. Pollution, disposal of waste products and changing land use has a significant effect on the
environment, and environmental chemists study how human activity has affected the Earth’s natural
cycles, and how damaging effects can be minimised.
4.10.1 Using the Earth's resources and obtaining potable water

4.10.1.1 Using the Earth's resources and sustainable development
development
Humans use the Earth’s resources to provide warmth, shelter, food
and transport.
Natural resources, supplemented by agriculture, provide food, timber,
clothing and fuels.
Finite resources from the Earth, oceans and atmosphere are
processed to provide energy and materials.
Chemistry plays an important role in improving agricultural and
industrial processes to provide new products and in sustainable
development, which is development that meets the needs of current
generations without compromising the ability of future generations to
meet their own needs.
• state examples of natural products that are supplemented or
replaced by agricultural and synthetic products
• distinguish between finite and renewable resources given
appropriate information.
• extract and interpret information about resources from charts, WS 3.2
graphs and tables MS 2c, 4a
• use orders of magnitude to evaluate the significance of data. MS 2h
Translate information
numeric form.
4.10.1.2 Potable water

development
Water of appropriate quality is essential for life. For humans, drinking
water should have sufficiently low levels of dissolved salts and
microbes. Water that is safe to drink is called potable water. Potable
water is not pure water in the chemical sense because it contains
dissolved substances.
The methods used to produce potable water depend on available
supplies of water and local conditions.
In the United Kingdom (UK), rain provides water with low levels of
dissolved substances (fresh water) that collects in the ground and in
lakes and rivers, and most potable water is produced by:
• choosing an appropriate source of fresh water
• passing the water through filter beds
• sterilising.
Sterilising agents used for potable water include chlorine, ozone or
ultraviolet light.
If supplies of fresh water are limited, desalination of salty water or sea
water may be required. Desalination can be done by distillation or
by processes that use membranes such as reverse osmosis. These
processes require large amounts of energy.
• distinguish between potable water and pure water
• describe the differences in treatment of ground water and salty
water
• give reasons for the steps used to produce potable water.
Required practical 8: analysis and purification of water samples from different sources, including pH,
dissolved solids and distillation.
AT skills covered by this practical activity: 2, 3 and 4.
4.10.1.3 Waste water treatment
development
Urban lifestyles and industrial processes produce large amounts of
waste water that require treatment before being released into the
environment. Sewage and agricultural waste water require removal
of organic matter and harmful microbes. Industrial waste water may
require removal of organic matter and harmful chemicals.
Sewage treatment includes:
• screening and grit removal
• sedimentation to produce sewage sludge and effluent
• anaerobic digestion of sewage sludge
• aerobic biological treatment of effluent.
Students should be able to comment on the relative ease of obtaining
potable water from waste, ground and salt water.
4.10.1.4 Alternative methods of extracting metals (HT only)

development
The Earth’s resources of metal ores are limited.
Copper ores are becoming scarce and new ways of extracting copper
from low-grade ores include phytomining, and bioleaching. These
methods avoid traditional mining methods of digging, moving and
disposing of large amounts of rock.
Phytomining uses plants to absorb metal compounds. The plants
are harvested and then burned to produce ash that contains metal
compounds.
Bioleaching uses bacteria to produce leachate solutions that contain
metal compounds.
The metal compounds can be processed to obtain the metal.
For example, copper can be obtained from solutions of copper
compounds by displacement using scrap iron or by electrolysis.
Students should be able to evaluate alternative biological methods of
metal extraction, given appropriate information.
4.10.2 Life cycle assessment and recycling

4.10.2.1 Life cycle assessment
development
Life cycle assessments (LCAs) are carried out to assess the WS 1.3, 4, 5
environmental impact of products in each of these stages: LCAs should be done as a
• extracting and processing raw materials comparison of the impact
• manufacturing and packaging on the environment of
the stages in the life of a
• use and operation during its lifetime
product, and only quantified
• disposal at the end of its useful life, including transport and where data is readily
distribution at each stage. available for energy, water,
Use of water, resources, energy sources and production of some resources and wastes.
wastes can be fairly easily quantified. Allocating numerical values Interpret LCAs of materials
to pollutant effects is less straightforward and requires value or products given
judgements, so LCA is not a purely objective process. appropriate information.
Selective or abbreviated LCAs can be devised to evaluate a product MS 1a
but these can be misused to reach pre-determined conclusions, eg in
Recognise and use
support of claims for advertising purposes.
Students should be able to carry out simple comparative LCAs for
MS 1c
shopping bags made from plastic and paper.
percentages.
MS 1d
Make estimates of
the results of simple
calculations.
MS 2a
Use an appropriate number
of significant figures.
MS 4a
Translate information
numeric form.
4.10.2.2 Ways of reducing the use of resources
development
The reduction in use, reuse and recycling of materials by end users
reduces the use of limited resources, use of energy sources, waste
and environmental impacts.
Metals, glass, building materials, clay ceramics and most plastics
are produced from limited raw materials. Much of the energy for the
processes comes from limited resources. Obtaining raw materials
from the Earth by quarrying and mining causes environmental
impacts.
Some products, such as glass bottles, can be reused. Glass bottles
can be crushed and melted to make different glass products. Other
products cannot be reused and so are recycled for a different use.
Metals can be recycled by melting and recasting or reforming into
different products. The amount of separation required for recycling
depends on the material and the properties required of the final
product. For example, some scrap steel can be added to iron from a
blast furnace to reduce the amount of iron that needs to be extracted
from iron ore.
Students should be able to evaluate ways of reducing the use of
limited resources, given appropriate information.
4.10.3 Using materials (chemistry only)

4.10.3.1 Corrosion and its prevention
development
Corrosion is the destruction of materials by chemical reactions with
substances in the environment. Rusting is an example of corrosion.
Both air and water are necessary for iron to rust.
Corrosion can be prevented by applying a coating that acts as a
barrier, such as greasing, painting or electroplating. Aluminium has an
oxide coating that protects the metal from further corrosion.
Some coatings are reactive and contain a more reactive metal to
provide sacrificial protection, eg zinc is used to galvanise iron.
Students should be able to: WS 2.2, 7, 3.5
• describe experiments and interpret results to show that both air Investigate the conditions
and water are necessary for rusting for rusting.
• explain sacrificial protection in terms of relative reactivity.
4.10.3.2 Alloys as useful materials

development
Most metals in everyday use are alloys.
Bronze is an alloy of copper and tin. Brass is an alloy of copper and
zinc.
Gold used as jewellery is usually an alloy with silver, copper and zinc.
The proportion of gold in the alloy is measured in carats. 24 carat
being 100 % (pure gold), and 18 carat being 75 % gold.
Steels are alloys of iron that contain specific amounts of carbon and
other metals. High carbon steel is strong but brittle. Low carbon steel
is softer and more easily shaped. Steels containing chromium and
nickel (stainless steels) are hard and resistant to corrosion.
Aluminium alloys are low density.
Students should be able to: MS 1a
• recall a use of each of the alloys specified Recognise and use
• interpret and evaluate the composition and uses of alloys other expressions in decimal form.
than those specified given appropriate information.
MS 1c
percentages.
4.10.3.3 Ceramics, polymers and composites
development
Most of the glass we use is soda-lime glass, made by heating a
mixture of sand, sodium carbonate and limestone. Borosilicate glass,
made from sand and boron trioxide, melts at higher temperatures than
soda-lime glass.
Clay ceramics, including pottery and bricks, are made by shaping wet
clay and then heating in a furnace.
The properties of polymers depend on what monomers they are made
from and the conditions under which they are made. For example, low
density (LD) and high density (HD) poly(ethene) are produced from
ethene.
Thermosoftening polymers melt when they are heated. Thermosetting
polymers do not melt when they are heated.
• explain how low density and high density poly(ethene) are both
produced from ethene
• explain the difference between thermosoftening and thermosetting
polymers in terms of their structures.
Most composites are made of two materials, a matrix or binder
surrounding and binding together fibres or fragments of the other
material, which is called the reinforcement.
Students should be able to recall some examples of composites.
Students should be able to, given appropriate information: WS 1.4, 3.5, 3.8
• compare quantitatively the physical properties of glass and clay Compare the properties
ceramics, polymers, composites and metals of thermosetting and
• explain how the properties of materials are related to their uses and thermosoftening polymers.
select appropriate materials.
4.10.4 The Haber process and the use of NPK fertilisers

(chemistry only)
4.10.4.1 The Haber process
development
The Haber process is used to manufacture ammonia, which can be MS 1a
used to produce nitrogen-based fertilisers. Recognise and use
The raw materials for the Haber process are nitrogen and hydrogen.
MS 1c
Students should be able to recall a source for the nitrogen and a
source for the hydrogen used in the Haber process. Use ratios, fractions and
percentages.
The purified gases are passed over a catalyst of iron at a high
temperature (about 450°C) and a high pressure (about 200
atmospheres). Some of the hydrogen and nitrogen reacts to form
ammonia. The reaction is reversible so some of the ammonia
produced breaks down into nitrogen and hydrogen:
nitrogen + hydrogen ammonia
On cooling, the ammonia liquefies and is removed. The remaining

hydrogen and nitrogen are recycled.
(HT only) Students should be able to: MS 1a
• interpret graphs of reaction conditions versus rate Recognise and use
MS 1c
percentages.
• apply the principles of dynamic equilibrium in WS 3.5, 3.8
Reversible reactions and dynamic equilibrium to the Haber process
• explain the trade-off between rate of production and position of
equilibrium
• explain how the commercially used conditions for the Haber
process are related to the availability and cost of raw materials and
energy supplies, control of equilibrium position and rate.
4.10.4.2 Production and uses of NPK fertilisers
development
Compounds of nitrogen, phosphorus and potassium are used as AT 4
fertilisers to improve agricultural productivity. NPK fertilisers contain Prepare an ammonium salt.
compounds of all three elements.
Industrial production of NPK fertilisers can be achieved using a variety
of raw materials in several integrated processes. NPK fertilisers are
formulations of various salts containing appropriate percentages of
the elements.
Ammonia can be used to manufacture ammonium salts and nitric
acid.
Potassium chloride, potassium sulfate and phosphate rock are
obtained by mining, but phosphate rock cannot be used directly as a
fertiliser.
Phosphate rock is treated with nitric acid or sulfuric acid to produce
soluble salts that can be used as fertilisers.
• recall the names of the salts produced when phosphate rock is
treated with nitric acid, sulfuric acid and phosphoric acid
• compare the industrial production of fertilisers with laboratory
preparations of the same compounds, given appropriate
information.
4.11 Key ideas

The complex and diverse phenomena of the natural world can be described in terms of a small number
of key ideas in chemistry.
These key ideas are of universal application, and we have embedded them throughout the subject
content. They underpin many aspects of the science assessment and will therefore be assessed across
all papers.
These ideas include:
• matter is composed of tiny particles called atoms and there are about 100 different naturally
occurring types of atoms called elements
• elements show periodic relationships in their chemical and physical properties
• these periodic properties can be explained in terms of the atomic structure of the elements
• atoms bond by either transferring electrons from one atom to another or by sharing electrons
• the shapes of molecules (groups of atoms bonded together) and the way giant structures are
arranged is of great importance in terms of the way they behave
• there are barriers to reaction so reactions occur at different rates
• chemical reactions take place in only three different ways:
• proton transfer
• electron transfer
• electron sharing
• energy is conserved in chemical reactions so can therefore be neither created or destroyed.
5 Scheme of assessment
Find past papers and mark schemes, and specimen papers for new courses, on our website at
aqa.org.uk/pastpapers
This specification is designed to be taken over two years.
This is a linear qualification. In order to achieve the award, students must complete all assessments at
the end of the course and in the same series.
GCSE exams and certification for this specification are available for the first time in May/June 2018 and
then every May/June for the life of the specification.
All materials are available in English only.
Our GCSE exams in Chemistry include questions that allow students to demonstrate:
• their knowledge and understanding of the content developed in one section or topic, including the
associated mathematical and practical skills or
• their ability to apply mathematical and practical skills to areas of content they are not normally
developed in or
• their ability to draw together different areas of knowledge and understanding within one answer.
A range of question types will be used, including multiple choice, short answer and those that require
extended responses. Extended response questions will be of sufficient length to allow students to
demonstrate their ability to construct and develop a sustained line of reasoning which is coherent,
relevant, substantiated and logically structured. Extended responses may be prose, extended
calculations, or a combination of both, as appropriate to the question.
5.1 Aims and learning outcomes

Chemistry should be taught in progressively greater depth over the course of Key Stage 3 and Key
Stage 4. GCSE outcomes may reflect or build upon subject content which is typically taught at Key
Stage 3. There is no expectation that teaching of such content should be repeated during the GCSE
course where it has already been covered at an earlier stage.
GCSE study in chemistry provides the foundations for understanding the material world. Scientific
understanding is changing our lives and is vital to the world’s future prosperity, and all students
should be taught essential aspects of the knowledge, methods, processes and uses of science. They
should be helped to appreciate how the complex and diverse phenomena of the natural world can be
described in terms of a small number of key ideas relating to the sciences which are both inter-linked,
and are of universal application. These key ideas include:
• the use of conceptual models and theories to make sense of the observed diversity of natural
phenomena
• the assumption that every effect has one or more cause
• that change is driven by differences between different objects and systems when they interact
• that many such interactions occur over a distance without direct contact
• that science progresses through a cycle of hypothesis, practical experimentation, observation, theory
development and review
• that quantitative analysis is a central element both of many theories and of scientific methods of
inquiry.
These key ideas are relevant in different ways and with different emphases in biology, chemistry and
physics: examples of their relevance to chemistry are given below.
The GCSE specification in chemistry should enable students to:
• develop scientific knowledge and conceptual understanding through chemistry
• develop understanding of the nature, processes and methods of science through different types of
scientific enquiries that help them to answer scientific questions about the world around them
• develop and learn to apply observational, practical, modelling, enquiry and problem-solving skills,
both in the laboratory, in the field and in other learning environments
• develop their ability to evaluate claims based on chemistry through critical analysis of the
methodology, evidence and conclusions, both qualitatively and quantitatively.
Chemistry should be studied in ways that help students to develop curiosity about the natural world,
insight into how science works, and appreciation of its relevance to their everyday lives. The scope
and nature of such study should be broad, coherent, practical and satisfying, and thereby encourage
students to be inspired, motivated and challenged by the subject and its achievements.
5.2 Assessment objectives

Assessment objectives (AOs) are set by Ofqual and are the same across all GCSE Chemistry
specifications and all exam boards.
The exams will measure how students have achieved the following assessment objectives.
• AO1: Demonstrate knowledge and understanding of: scientific ideas; scientific techniques and
procedures.
• AO2: Apply knowledge and understanding of: scientific ideas; scientific enquiry, techniques and
procedures.
• AO3: Analyse information and ideas to: interpret and evaluate; make judgments and draw
conclusions; develop and improve experimental procedures.
5.2.1 Assessment objective weightings for GCSE Chemistry

Assessment objectives (AOs) Component weightings Overall weighting
(approx %) (approx %)
Paper 1 Paper 2
AO1 37 ‒ 43 37 ‒ 43 40
AO2 37 ‒ 43 37 ‒ 43 40
AO3 17 ‒ 23 17 ‒ 23 20
Overall weighting of components 50 50 100
5.3 Assessment weightings
The marks awarded on the papers will be scaled to meet the weighting of the components. Students’
final marks will be calculated by adding together the scaled marks for each component. Grade
boundaries will be set using this total scaled mark. The scaling and total scaled marks are shown in the
table below.
Component Maximum raw mark Scaling factor Maximum scaled

mark
Paper 1 100 x1 100
Paper 2 100 x1 100
Total scaled mark: 200
6 General administration
You can find information about all aspects of administration, as well as all the forms you need, at
aqa.org.uk/examsadmin
6.1 Entries and codes

You only need to make one entry for each qualification – this will cover all the question papers and
certification.
Every specification is given a national discount (classification) code by the Department for Education
(DfE), which indicates its subject area.
If a student takes two specifications with the same discount code:
• further and higher education providers are likely to take the view that they have only achieved one of
the two qualifications
• only one of them will be counted for the purpose of the School and College Performance tables – the
DfE's rules on 'early entry' will determine which one.
Please check this before your students start their course.
Qualification title Tier AQA entry DfE discount

code code
AQA GCSE in Chemistry Foundation 8462F RD1
Higher 8462H
This specification complies with:

• Ofqual General conditions of recognition that apply to all regulated qualifications
• Ofqual GCSE qualification level conditions that apply to all GCSEs
• Ofqual GCSE subject level conditions that apply to all GCSEs in this subject
• all other relevant regulatory documents.
The Ofqual qualification accreditation number (QAN) is 601/8757/8.
6.2 Overlaps with other qualifications

There are no overlaps with any other AQA qualifications at this level.
6.3 Awarding grades and reporting results

The qualification will be graded on a nine-point scale: 1–9 – where 9 is the best grade.
A student taking Foundation Tier assessments will be awarded a grade within the range of 1 to 5.
Students who fail to reach the minimum standard for grade 1 will be recorded as U (unclassified) and
will not receive a qualification certificate.
A student taking Higher Tier assessments will be awarded a grade within the range of 4 to 9. A student
sitting the Higher Tier who just fails to achieve grade 4 will be awarded an allowed grade 3. Students
who fail to reach the minimum standard for the allowed grade 3 will be recorded as U (unclassified) and
will not receive a qualification certificate.
6.4 Re-sits and shelf life
Students can re-sit the qualification as many times as they wish, within the shelf life of the qualification.
6.5 Previous learning and prerequisites

There are no previous learning requirements. Any requirements for entry to a course based on this
specification are at the discretion of schools and colleges.
6.6 Access to assessment: diversity and inclusion

General qualifications are designed to prepare students for a wide range of occupations and further
study. Therefore our qualifications must assess a wide range of competences.
The subject criteria have been assessed to see if any of the skills or knowledge required present any
possible difficulty to any students, whatever their ethnic background, religion, sex, age, disability or
sexuality. If any difficulties were encountered, the criteria were reviewed again to make sure that tests of
specific competences were only included if they were important to the subject.
As members of the Joint Council for Qualifications (JCQ) we participate in the production of the JCQ
document Access Arrangements and Reasonable Adjustments: General and Vocational qualifications.
We follow these guidelines when assessing the needs of individual students who may require an access
arrangement or reasonable adjustment. This document is published on the JCQ website at jcq.org.uk
6.6.1 Students with disabilities and special needs

We can make arrangements for disabled students and students with special needs to help them access
the assessments, as long as the competences being tested are not changed. Access arrangements
must be agreed before the assessment. For example, a Braille paper would be a reasonable adjustment
for a Braille reader but not for a student who does not read Braille.
We are required by the Equality Act 2010 to make reasonable adjustments to remove or lessen any
disadvantage that affects a disabled student.
If you have students who need access arrangements or reasonable adjustments, you can apply using
the Access arrangements online service at aqa.org.uk/eaqa
6.6.2 Special consideration

We can give special consideration to students who have been disadvantaged at the time of the
assessment through no fault of their own – for example a temporary illness, injury or serious problem
such as the death of a relative. We can only do this after the assessment.
Your exams officer should apply online for special consideration at aqa.org.uk/eaqa
For more information and advice about access arrangements, reasonable adjustments and special
consideration please see aqa.org.uk/access or email [email protected]
6.7 Working with AQA for the first time

If your school or college has not previously offered any AQA specification, you need to register as an
AQA centre to offer our specifications to your students. Find out how at aqa.org.uk/becomeacentre
6.8 Private candidates

A private candidate is someone who enters for exams through an AQA-approved school or college but
is not enrolled as a student there.
If you are a private candidate you may be self-taught, home-schooled or have private tuition, with a
tutor or distance learning organisation. You must be based in the UK.
All GCSE science students need to complete practical experiments as part of their learning. A minimum
of 8 experiments are required for this chemistry specification. This equips students with essential
practical knowledge and experiences, enables them to put theory into practice and helps them develop
skills for higher education.
Private candidates wishing to study GCSE sciences need to find a school or college who will
let them carry out the required practicals. Schools and colleges accepting private candidates
must make provision for them to carry out all of the required practical activities as specified in
Practical assessment. This is likely to incur a cost. We recommend you contact your local schools and
colleges to organise this as early as possible.
Students won’t be assessed whilst conducting their practical work, but the written exam will
include questions on it. Therefore, candidates lacking hands on experience will be at an immediate
disadvantage.
If you have any queries as a private candidate, you can:
• speak to the exams officer at the school or college where you intend to take your exams
• visit our website at aqa.org.uk/exams-administration
• email: [email protected]
7 Mathematical requirements
Students will be required to demonstrate the following mathematics skills in GCSE Chemistry
assessments. Questions will target maths skills at a level of demand appropriate to each subject. In
Foundation Tier papers questions assessing maths requirements will not be lower than that expected
at Key Stage 3 (as outlined in Mathematics Programmes of Study: Key Stage 3, by the DfE, document
reference DFE-00179-2013). In Higher Tier papers questions assessing maths requirements will not be
lower than that of questions and tasks in assessments for the Foundation Tier in a GCSE Qualification
in Mathematics.
1 Arithmetic and numerical computation

a Recognise and use expressions in decimal form
b Recognise and use expressions in standard form
c Use ratios, fractions and percentages
d Make estimates of the results of simple calculations
2 Handling data
a Use an appropriate number of significant figures
b Find arithmetic means
c Construct and interpret frequency tables and diagrams, bar charts and histograms
h Make order of magnitude calculations
3 Algebra
a Understand and use the symbols: =, <, <<, >>, >, ∝ , ~
b Change the subject of an equation
c Substitute numerical values into algebraic equations using appropriate units for physical quantities
4 Graphs
a Translate information between graphical and numeric form
b Understand that y = mx + c represents a linear relationship
c Plot two variables from experimental or other data
d Determine the slope and intercept of a linear graph
e Draw and use the slope of a tangent to a curve as a measure of rate of change
5 Geometry and trigonometry

b Visualise and represent 2D and 3D forms including two dimensional representations of 3D objects
c Calculate areas of triangles and rectangles, surface areas and volumes of cubes
Mathematical skills references are taken from the DfE subject criteria. Where there is a break in a
sequence, the 'missing' references are criteria not applicable to GCSE Chemistry and have been
deliberately omitted from this list.
8 Practical assessment
Practical work is at the heart of chemistry, so we have placed it at the heart of this specification.
There are three interconnected, but separate reasons for doing practical work in schools. They are:
1 To support and consolidate scientific concepts (knowledge and understanding).
This is done by applying and developing what is known and understood of abstract ideas and
models. Through practical work we are able to make sense of new information and observations,
and provide insights into the development of scientific thinking.
2 To develop investigative skills. These transferable skills include:
• devising and investigating testable questions
• identifying and controlling variables
• analysing, interpreting and evaluating data.
3 To build and master practical skills such as:
• using specialist equipment to take measurements
• handling and manipulating equipment with confidence and fluency
• recognising hazards and planning how to minimise risk.
By focusing on the reasons for carrying out a particular practical, teachers will help their students
understand the subject better, to develop the skills of a scientist and to master the manipulative skills
required for further study or jobs in STEM subjects.
Questions in the written exams will draw on the knowledge and understanding students have gained
by carrying out the practical activities listed below. These questions will count for at least 15 % of the
overall marks for the qualification. Many of our questions will also focus on investigative skills and how
well students can apply what they know to practical situations often in novel contexts.
The practical handbook will help teachers plan purposeful practical work that develops both practical
and investigative skills and encourages the thinking behind the doing so that they can reach their
potential.
Teachers are encouraged to further develop students’ abilities by providing other opportunities for
practical work throughout the course. Opportunities are signposted in the right-hand column of the
content section of this specification for further skills development.
Our chemistry scheme of work will provide ideas and suggestions for good practical activities that are
manageable with large classes.
8.1 Use of apparatus and techniques
All students are expected to have carried out the required practical activities in
Required practical activities.
The following list includes opportunities for choice and use of appropriate laboratory apparatus for a
variety of experimental problem-solving and/or enquiry-based activities.
Safety is an overriding requirement for all practical work. Schools and colleges are responsible for
ensuring that appropriate safety procedures are followed whenever their students undertake practical
work, and should undertake full risk assessments.
Use and production of appropriate scientific diagrams to set up and record apparatus and procedures
used in practical work is common to all science subjects and should be included wherever appropriate.
AT 1 – 7 are common with combined science. AT 8 is chemistry only.
Apparatus and techniques

AT 1 Use of appropriate apparatus to make and record a range of measurements accurately,
including mass, time, temperature, and volume of liquids and gases (links to A-level AT a).
AT 2 Safe use of appropriate heating devices and techniques including use of a Bunsen burner
and a water bath or electric heater (links to A-level AT b).
AT 3 Use of appropriate apparatus and techniques for conducting and monitoring chemical
reactions, including appropriate reagents and/or techniques for the measurement of pH in
different situations (links to A-level AT a and d).
AT 4 Safe use of a range of equipment to purify and/or separate chemical mixtures including
evaporation, filtration, crystallisation, chromatography and distillation (links to A-level AT d
and g).
AT 5 Making and recording of appropriate observations during chemical reactions including
changes in temperature and the measurement of rates of reaction by a variety of methods
such as production of gas and colour change (links to A-level AT a and l).
AT 6 Safe use and careful handling of gases, liquids and solids, including careful mixing of
reagents under controlled conditions, using appropriate apparatus to explore chemical
changes and/or products (links to A-level AT a and k).
AT 7 Use of appropriate apparatus and techniques to draw, set up and use electrochemical
cells for separation and production of elements and compounds (links to A-level AT d
and j).
AT 8 Use of appropriate qualitative reagents and techniques to analyse and identify unknown
(chemistry samples or products including gas tests, flame tests, precipitation reactions, and the
only) determination of concentrations of strong acids and strong alkalis (links to A-level AT d).
8.2 Required practical activities

The following practical activities must be carried out by all students taking GCSE Chemistry.
Following any revision by the Secretary of State of the apparatus or techniques specified, we will review
and revise the required practical activities as appropriate.
Schools and colleges will be informed of any changes in a timely manner and the amended
specification will be published highlighting the changes accordingly.
Teachers are encouraged to vary their approach to these practical activities. Some are more suitable for
highly structured approaches that develop key techniques while others allow opportunities for students
to develop investigative approaches.
This list is not designed to limit the practical activities carried out by students. A rich practical
experience will include more than the eight required practical activities. The explicit teaching of practical
skills will build students’ competence. Many teachers will also use practical approaches to introduce
content knowledge in the course of their normal teaching.
Schools and colleges are required to provide a practical science statement to AQA, that is a true and
accurate written statement, which confirms that it has taken reasonable steps to secure that each
student has:
• completed the required practical activities as detailed in this specification
• made a contemporaneous record of such work undertaken during the activities and the knowledge,
skills and understanding derived from those activities.
We will provide a form for the head of centre to sign. You must submit the form to us by the date
published at aqa.org.uk/science. We will contact schools and colleges directly with the deadline date
and send timely reminders if the form is not received. Failure to send this form counts as malpractice/
maladministration, and may result in formal action or warning for the school or college.
Practicals 1, 3, 4, 5, 6 and 8 are common with GCSE Combined Science: Trilogy and GCSE Combined
Science: Synergy. Practicals 2 and 7 are GCSE Chemistry only.
8.2.1 Required practical activity 1

Preparation of a pure, dry sample of a soluble salt from an insoluble oxide or carbonate, using a Bunsen
burner to heat dilute acid and a water bath or electric heater to evaporate the solution.

In doing this practical students should cover these parts of the apparatus and techniques requirements.
AT 2 – safe use of appropriate heating devices and techniques including use of a Bunsen burner and a
water bath or electric heater.
AT 3 – use of appropriate apparatus and techniques for conducting chemical reactions, including
appropriate reagents.
AT 4 – safe use of a range of equipment to purify and/or separate chemical mixtures including
evaporation, filtration, crystallisation.
AT 6 – safe use and careful handling of liquids and solids, including careful mixing of reagents under
controlled conditions.
Key opportunities for skills development
In doing this practical there are key opportunities for students to develop the following skills.
WS 2.3 – apply a knowledge of a range of techniques, instruments, apparatus, and materials to select
those appropriate to the experiment.
WS 2.4 – carry out experiments appropriately having due regard for the correct manipulation of
apparatus, the accuracy of measurements and health and safety considerations.

(Chemistry only) determination of the reacting volumes of solutions of a strong acid and a strong alkali
by titration.
(HT only) determination of the concentration of one of the solutions in mol/dm3 and g/dm3 from the
reacting volumes and the known concentration of the other solution.

AT 1 – use of appropriate apparatus to make and record a range of measurements accurately, including
volume of liquids.
AT 8 – the determination of concentrations of strong acids and strong alkalis.
Key opportunities and skills development

WS 2.6 – make and record observations and measurements using a range of apparatus and methods.
MS 1a – recognise and use expressions in decimal form.
MS 1c – use ratios, fractions and percentages.
MS 2a – use an appropriate number of significant figures.

Investigate what happens when aqueous solutions are electrolysed using inert electrodes. This should
be an investigation involving developing a hypothesis.

AT 3 – use of appropriate apparatus and techniques for conducting and monitoring chemical reactions.
AT 7 – use of appropriate apparatus and techniques to draw, set up and use electrochemical cells for
separation and production of elements and compounds.
AT 8 – use of appropriate qualitative reagents and techniques to analyse and identify unknown samples
or products including gas tests for hydrogen, oxygen and chlorine.

WS 2.1 – use scientific theories and explanations to develop hypotheses.

WS 2.2 – plan experiments or devise procedures to make observations, produce or characterise a
substance, test hypotheses, check data or explore phenomena.

Investigate the variables that affect temperature changes in reacting solutions such as, eg acid plus
metals, acid plus carbonates, neutralisations, displacement of metals.

mass, temperature, and volume of liquids.
AT 5 – making and recording of appropriate observations during chemical reactions including changes
in temperature.
AT 6 – safe use and careful handling of gases, liquids and solids, including careful mixing of reagents
under controlled conditions, using appropriate apparatus to explore chemical changes.

WS 2.7 – evaluate methods and suggest possible improvements and further investigations.
MS 2b – find arithmetic means.
MS 4a – translate information between graphical and numeric form.
MS 4c – plot two variables from experimental or other data.
Investigate how changes in concentration affect the rates of reactions by a method involving measuring
the volume of a gas produced and a method involving a change in colour or turbidity. This should be an
investigation involving developing a hypothesis.

mass, time, temperature, and volume of liquids and gases.
AT 5 – making and recording of appropriate observations during chemical reactions including the
measurement of rates of reaction by a variety of methods such as production of gas and colour change.
AT 6 – safe use and careful handling of gases, liquids and solids, including careful mixing of reagents
under controlled conditions, using appropriate apparatus to explore chemical changes.

MS 1c – use ratios, fractions and percentages.
MS 1d – make estimates of the results of simple calculations.
MS 2b – find arithmetic means.
MS 4a – translate information between graphical and numeric form.
MS 4b – understand that y = mx + c represents a linear relationship.
MS 4c – plot two variables from experimental or other data.
MS 4d – determine the slope and intercept of a linear graph.
MS 4e – draw and use the slope of a tangent to a curve as a measure of rate of change.

Investigate how paper chromatography can be used to separate and tell the difference between
coloured substances. Students should calculate Rf values.

AT 1 – use of appropriate apparatus to make and record a range of measurements accurately.
chromatography.

8.2.7 Required practical activity 7 (chemistry only)

Use of chemical tests to identify the ions in unknown single ionic compounds covering the ions from
sections Flame tests through to Sulfates.

AT 1 – safe use of a Bunsen burner.
AT 8 – use of appropriate qualitative reagents and techniques to analyse and identify unknown samples
or products including gas tests, flame tests, precipitation reactions.

Analysis and purification of water samples from different sources, including pH, dissolved solids and
distillation.

AT 2 – safe use of appropriate heating devices and techniques including use of a Bunsen burner and a
water bath or electric heater.
AT 3 – use of appropriate apparatus and techniques for the measurement of pH in different situations.
evaporation, distillation.

WS 2.5 – recognise when to apply a knowledge of sampling techniques to ensure any samples
collected are representative.
9 Appendix A: periodic table

The periodic table has been updated to take into account recent developments.
Get help and support
Visit our website for information, guidance, support and resources at aqa.org.uk/8462
You can talk directly to the science subject team
E: [email protected]
T: 01483 477 756
aqa.org.uk
Copyright © 2016 AQA and its licensors. All rights reserved.
AQA retains the copyright on all its publications, including the specifications. However, schools and colleges registered with AQA are permitted to copy
material from this specification for their own internal use.
G00569
AQA Education (AQA) is a registered charity (number 1073334) and a company limited by guarantee registered in England and Wales (company number
3644723). Our registered address is AQA, Devas Street, Manchester M15 6EX.

Chemistry

Uploaded by

Copyright:

Available Formats

Chemistry

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Chemistry

Uploaded by

Copyright:

Available Formats

GCSE

Version 1.0 22 April 2016

9 Appendix A: periodic table 99

Are you using the latest version of this specification?

Our specification has been developed with teachers

Our practicals have been trialled by teachers

Straightforward exams, so students can give straightforward answers

1.2 Support and resources to help you teach

Preparing for exams

Analyse your students' results with Enhanced Results Analysis (ERA)

Keep your skills up-to-date with professional development

Help and support available

2.1 Subject content

1 Development of scientific thinking

2 Experimental skills and strategies

Students should be able to: Examples of what students could be asked to do

Students should be able to: Examples of what students could be asked to do

4.1.1 A simple model of the atom, symbols, relative atomic mass,

4.1.1.4 Relative electrical charges of subatomic particles

In an atom, the number of electrons is equal to the number of protons

4.1.1.5 Size and mass of atoms

Students should be able to calculate the numbers of protons,

4.1.1.6 Relative atomic mass

4.1.2 The periodic table

4.1.2.2 Development of the periodic table

4.1.2.3 Metals and non-metals

4.1.3 Properties of transition metals (chemistry only)

4.1.3.2 Typical properties

4.2.1 Chemical bonds, ionic, covalent and metallic

4.2.1.2 Ionic bonding

Content Key opportunities for skills

4.2.1.3 Ionic compounds

Students should be able to: WS 1.2

Some covalently bonded substances have very large molecules, such

Polymers can be represented in the form:

where n is a large number.

Content Key opportunities for skills

4.2.1.5 Metallic bonding

The amount of energy needed to change state from solid to liquid

4.2.2.2 State symbols

4.2.2.3 Properties of ionic compounds

4.2.2.4 Properties of small molecules

4.2.2.7 Properties of metals and alloys

4.2.2.8 Metals as conductors

4.2.3 Structure and bonding of carbon

4.2.3.3 Graphene and fullerenes

4.2.4.2 Uses of nanoparticles

4.3 Quantitative chemistry

4.3.1 Chemical measurements, conservation of mass and the quantitative

4.3.1.2 Relative formula mass

4.3.1.4 Chemical measurements

4.3.2 Use of amount of substance in relation to masses of pure substances

One mole of a substance contains the same number of the stated MS 1b

4.3.2.3 Using moles to balance equations (HT only)

4.3.2.4 Limiting reactants (HT only)

4.3.2.5 Concentration of solutions

4.3.3 Yield and atom economy of chemical reactions (chemistry only)

The amount of a product obtained is known as the yield. When MS 2a

4.3.4 Using concentrations of solutions in mol/dm3 (chemistry only)