Scribd Logo
Upload

Welcome to Scribd!

  • 37 views

    T1 PCM Ind DS

    Uploaded by

    Tran
    This document describes the T1-PCM-IND digital telemetry system for wireless transmission of strain gauge signals from rotating shafts. The system consists of an encoder that attaches to the rotating shaft and transmits data inductively to a receiver unit. The encoder supports strain gauge sensors in full- or half-bridge configurations. The receiver provides analog +/- 10V outputs and optional 4-20mA output. The system provides easy, wireless transmission of strain gauge data up to 30mm from the rotating shaft.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    T1 PCM Ind DS

    Uploaded by

    Tran
    37 views4 pages
    This document describes the T1-PCM-IND digital telemetry system for wireless transmission of strain gauge signals from rotating shafts. The system consists of an encoder that attaches to the rotating shaft and transmits data inductively to a receiver unit. The encoder supports strain gauge sensors in full- or half-bridge configurations. The receiver provides analog +/- 10V outputs and optional 4-20mA output. The system provides easy, wireless transmission of strain gauge data up to 30mm from the rotating shaft.

    Original Description:

    Telemetry modul KMT

    Original Title

    T1-PCM-IND-DS

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document describes the T1-PCM-IND digital telemetry system for wireless transmission of strain gauge signals from rotating shafts. The system consists of an encoder that attaches to the rotating shaft and transmits data inductively to a receiver unit. The encoder supports strain gauge sensors in full- or half-bridge configurations. The receiver provides analog +/- 10V outputs and optional 4-20mA output. The system provides easy, wireless transmission of strain gauge data up to 30mm from the rotating shaft.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    37 views4 pages

    T1 PCM Ind DS

    Uploaded by

    Tran
    This document describes the T1-PCM-IND digital telemetry system for wireless transmission of strain gauge signals from rotating shafts. The system consists of an encoder that attaches to the rotating shaft and transmits data inductively to a receiver unit. The encoder supports strain gauge sensors in full- or half-bridge configurations. The receiver provides analog +/- 10V outputs and optional 4-20mA output. The system provides easy, wireless transmission of strain gauge data up to 30mm from the rotating shaft.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    KMT - Kraus Messtechnik GmbH

    Gewerbering 9, D-83624 Otterfing, Germany,  08024-48737, Fax. 08024-5532


    Home Page http://www.kmt-telemetry.com, Email: [email protected]

    T1-PCM-IND
    Digital telemetry system for strain gage
    applications on rotating shafts

    • Easy to assemble and operate • Distance up to 30mm (Range)

    • Strain gage sensors (>=350 Ohm) • Powering of transmitter part inductive

    • Full- and half bridge configuration • No influence through radio frequency

    • Excitation fixed 4 Volt DC • Many systems can operated at the same time

    • Auto-Zero adjustment • Signal bandwidth 0…1200Hz (-3dB)

    • Gain: 250-500-1000-2000 or 1000-2000-4000-8000 • Output +/-10V

    • 16 bit ADC • Output 4-20mA (Option)

    • Digital transmission realized inductively • System accuracy <0.2%


    General description
    The T1-PCM-IND single-channel telemetry system offers the easiest handling for the wireless transmission of strain gage
    signals from rotating shafts. The encoder 35x24x14mm with a weight of 16g. The transmitter (encoder) part is simply mounted
    on the rotating shaft with a special fiber reinforced tape.
    The data transfer between transmitter and receiver is digital. The powering of the transmission part by the T1-PCM-IND is
    inductive!.
    Functional description
    The T1-PCM-IND transmitter provides a pulse code modulated signal (PCM) to an induction winding around the shaft. The
    magnetic field of this winding enables the inductive transmission of the signal from coil to pickup. From there the signal is
    transferred by cable (5 m) to the receiver. The maximum distance between the transmitter coil and the pickup/powerhead is
    30mm.
    The receiver unit offers a BNC connector at the front panel with analog outputs  10 V and optional a current output of 4-20mA
    Strain gage sensors (>=350 Ohm) in full- and half- bridge configuration can be directly connected to the transmitter. The
    excitation is fixed to 4 Volt DC and the gain is set by plug-In bridge in 4 steps (250-500-1000-2000 or 1000-2000-4000-8000).
    An auto-zero (AZ) adjustment is executed by pressing the AZ button on the front side of the receiver. The successful AZ
    operation is indicated by a yellow LED. The yellow LED flashes as long as the AZ is in progress. When the AZ completes the
    LED continuously illuminates. The AZ setting is stored in a Flash-RAM and thus is not lost during power-off.
    T1-PCM-IND set contains:

    Inductive Pickup/Powerhead T1-PCM-DEC Mounting tape Ferrite tape - 30mm x 3 meter


    with 5m cable (Decoder) 2 x 25mm x 50m (isolate magnetic field between
    shaft and coil)

    CUL wire
    0.5mm for coil
    (Enamelled copper
    wire)

    T1-PCM-STG-(IND) Hexagon key to


    DC-Power cable (Encoder for strain gages) activate AZ switch

    Version 2019-05 Technical Data are subject to change without notice!


    2
    Technical data transmitting part:

    T1-PCM-STG
    Strain gage: Full and half bridge >=350 Ohm,
    Excitation: 4 VDC (fixed)
    Gain: 250-500-1000-2000 standard
    1000-2000-4000-8000 on request!
    Gain and Sensitivity
    Gain 250 = +/-10mV/V Gain 2000 = +/-1.250mV/V
    Gain 500 = +/-5mV/V Gain 4000 = +/-0.625mV/V
    Gain 1000 = +/-2.5mV/V Gain 8000 = +/-0.3125mV/V
    AZ: Auto Zero calibration (via AZ button from receiver side)
    Analog signal bandwidth: 0 - 1200 Hz (-3 dB)
    Operating temperature: - 40 to + 85 °C
    Resolution 16bit
    Scanning rate 6.41 kHz
    Static acceleration: up to 3000g
    Powering: inductive
    Dimensions: 35x24x14mm, weight 16g
    Housing: splash-water resistant IP65 (except the connector pins)

    T1-PCM-Pt100
    Pt100 thermo sensor
    Measurement range -50 to 250°C or -50 to 500°C (select by jumper)
    Analog signal bandwidth: 0 - 10 Hz (-3 dB)
    Operating temperature: - 40 to + 85 °C
    Resolution 16bit
    Scanning rate 6.41kHz
    Static acceleration: up to 3000g
    Powering: inductive
    Dimensions: 35x24x14mm, weight 16g
    Housing: splash-water resistant IP65 (except the connector pins)

    Version 2019-05 Technical Data are subject to change without notice!


    3
    Technical data receiving part
    T1-PCM-DEC
    Analogue output: +/-10V via BNC output 1200Hz
    (delay between analog IN/OUT 1.8mS constant!!)
    Optional add. 4-20mA output to the analog output
    Auto Zero setting: via AZ button
    Autozero LED:
    Yellow ON- successful AZ
    Yellow OFF- not successful AZ
    if flashing, call support of KMT, error in EPROM
    SL LED: Red ON = if error of data transmitting
    SL LED: Red Flashing = distance to far
    Power ON LED: Red ON = if power switch on
    Output to Powerhead: via 6-pol. Tuchel
    Fuse LED: Flashing if fuse is defect
    Front Rear Powering: 10-30V DC, Input via 7-pol. Tuchel
    Switch: ON/OFF
    Operating temperature: - 40 to +70 °C
    Dimensions: 75 x 105 x 105 (without connectors!)
    Optional top-hat rail clip
    Weight 750 grams
    Static acceleration: up to 200g
    System accuracy*: +/- 0.2 %
    <*measure with gain 1000, 350ohm (0.1%) full bridge - test bridge!!>
    T1-PCM-Pickup/Powerhead (standard version) other on request!!
    Function: Receiving inductive PCM modulated data from the coil of
    the T1-PCM-STG unit
    Inductive frequency is 60kHz
    Distance between the transmitter coil and the pickup is 5-30*mm
    Output to T1-PCM-Decoder: Via 6-pol. Tuchel plug incl. 5m cable
    Operating temperature: - 40 to +80 °C
    Dimensions: 53x66x30mm (without cable)
    Weight: 200 grams (without cable!)
    Housing: splash-water resistant IP65 (except connector).
    Cable length standard 5m! Optional 10, 15, 20 or 25m
    *(depend of shaft diameter!)

    Version 2019-05 Technical Data are subject to change without notice!


    4

    You might also like