Scribd
Upload
338 views6 pages

DIY Walking Robot Instruction Manual (English)

1) This document provides instructions for building a DIY walking robot out of pre-cut wood, metal shafts, a motor, grippers and other accessories. 2) The 10 steps include connecting the wood pieces together using short metal shafts and orange grippers, attaching the battery holder and DC motor, and testing it with batteries. 3) Once fully constructed following the illustrated steps, the robot will be ready to function and "race" powered by the batteries and motor.

Uploaded by

Abdullah husain
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
338 views6 pages

DIY Walking Robot Instruction Manual (English)

1) This document provides instructions for building a DIY walking robot out of pre-cut wood, metal shafts, a motor, grippers and other accessories. 2) The 10 steps include connecting the wood pieces together using short metal shafts and orange grippers, attaching the battery holder and DC motor, and testing it with batteries. 3) Once fully constructed following the illustrated steps, the robot will be ready to function and "race" powered by the batteries and motor.

Uploaded by

Abdullah husain
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Brought to you by Cytron Technologies

 
 
DIY Walking Robot 
 
Building Instruction Manual 
 

 
 
 
 
 
 
 
 
 
Brought to you by Cytron Technologies

Materials 

 
 
1 - 5.  Pre-cut wood 
6.  Double-sided tape 
7.  Short metal shaft 
8.  Long metal shaft 
9.  Green motor connector 
10.  Double-sided eyes accessories 
11.  Orange grippers 
12.  AA battery holder 
13.  DC Motor 
 
 
 
 
 
 
 
 
Brought to you by Cytron Technologies

Instructions 
Step 1: Fix 2 pieces of ​Wood 1​ on top of ​Wood 4 ​as shown below: 

 
 
Step 2: Fix ​Wood 2 ​at the back of ​Wood 4. 

 
 
Step 3: Connect ALL ​Wood 3​ and ​Wood 5​ together using the ​short metal shaft 
and ​orange gripper ​as shown below. 

 
 
Brought to you by Cytron Technologies

Step 4: Connect the ​battery holder wires​ to the ​DC motor. 

 
 
Step 5: Fix the ​green connector ​on both sides of the ​DC motor​ and connect a 
short metal shaft​ on each side. (Ensure the ​metal shafts​ connected are on the 
opposite direction for each side.) 

 
 
Step 6: Stick a piece of ​double-sided​ ​tape​ at the back of the battery holder and 
the ​DC motor​. 

 
 
Brought to you by Cytron Technologies

Step 7: Insert the ​long metal shaft ​through ​Wood 1​ and fix 2 ​orange gripper​ on 
each side.  

 
 
Step 8: Stick the ​battery holder ​at the top of ​Wood 4​ and the ​DC motor​ at the 
bottom. 

 
 
Step 9: Join all ​Wood 3 and 4​ in the position as shown below, ensure the sharper 
edge of ​Wood 3​ is facing outward as highlighted in the red box shown: 

 
Brought to you by Cytron Technologies

Step 10: Stick the ​eyes accessories ​on ​Wood 2​. 

 
 
Step 11: Attach 2 ​AA batteries​ to the ​battery holder​ and flip the metal switch to 
test the robot. 

 
 
The robot is now ready to race! Have fun! 

You might also like