6.

2B: Step-by-Step Procedures for Boiling Point Determination

There are a variety of methods by which a sample's boiling point can be determined, including distillation, reflux, and by using
a Thiele tube. The most straightforward method uses a Thiele tube, and has the advantage of using less than 0.5 mL of
material.

Distillation Method
There are simpler methods than a distillation to measure a compound's boiling point, and it is recommended to explore other
options (e.g. Thiele tube) if this is the only goal. However, if materials are limited, or if a purification is planned anyhow, a
distillation can be used to determine a compound's boiling point. The distillation technique is discussed in great detail in
Chapter 5.
A simple distillation should suffice for most situations (Figure 6.19), and at least 5 mL of sample should be used in the
distilling flask along with a few boiling stones or stir bar. As the bulk of the material distills, the highest temperature noted on
the thermometer corresponds to the boiling point. A major source of error with this method is recording too low a temperature,
before hot vapors fully immerse the thermometer bulb. Be sure to monitor the thermometer periodically, especially when the
5

distillation is active. Record the barometric pressure along with the boiling point.

Figure 6.19: Simple distillation.

Reflux Method
A reflux setup can also be used to determine a compound's boiling point. Reflux is when a liquid is actively boiling and
condensing, with the condensed liquid returning to the original flask. It is analogous to a distillation setup, with the main
difference being the vertical placement of the condenser.

Figure 6.20: a) Reflux setup, b) Insertion of digital thermometer into condenser, c) Position of thermometer, d) Cooling the
setup.

Lisa Nichols 10/18/2020 6.2B.1 CC-BY-NC-ND https://chem.libretexts.org/@go/page/95736

If materials are available, the best reflux setup for this application is shown in Figure 6.20b and uses a microscale condenser
and digital thermometer. The setup uses 5 mL of liquid, and a few boiling stones or stir bar. The condenser is attached to the
round bottomed flask, with the lower water hose connected to the water spigot and the upper water hose draining to the sink. It
is important to check that the joint connecting the flask and condenser is securely fastened. The liquid is brought to a boil on a
sand bath, and the thermometer is placed low into the apparatus (Figure 6.20c) such that the bottom inch is between the boiling
liquid and the bottom of the condenser. In this position, the thermometer can accurately measure the hot vapors and the
temperature will stabilize at the compound's boiling point. Record the barometric pressure along with the boiling point.
6

Although it might seem prudent to plunge the thermometer directly into the boiling liquid, it is possible the liquid may be
superheated, or hotter than its boiling point. After determining the boiling point, the flask should be raised from the sand bath
(Figure 6.20d) to cool, and condenser kept running until the flask is only warm to the touch. At this point the setup can be
dismantled.
If a microscale condenser is not available, an alternative reflux method can also be used as shown in Figure 6.21. Roughly
5 mL of sample is placed in a medium test tube (18 x 150 mm) with thermometer clamped inside so it does not touch the

sides of the glass. The apparatus is carefully heated on a sand bath such that reflux happens controllably and vapors do not
escape from the tube. The temperature during reflux will eventually stabilize (this takes some time), and the highest
temperature noted corresponds to the compound's boiling point. The boiling points measured with this method may have
6

significant error if the boiling point is very low or high (< 70 C or > 150 C ) as low boiling compounds boil away too easily
o o

and high boiling compounds tend to cool too easily.

Figure 6.21: Reflux apparatus using a sand bath and test tube.

Thiele Tube Method

Thiele Tube Theory
The Thiele tube method is one of the simplest methods to determine a compound's boiling point, and has the advantage of
using small amounts of material (less than 0.5 mL of sample). The sample is placed in a small tube along with an inverted
capillary tube. The setup is attached to a thermometer (Figure 6.23a) and heated inside a Thiele tube (Figure 6.22a) to slightly
higher than the compound's boiling point (which is evidenced by a continuous stream of bubbles emerging from the capillary
tube). The tube is then allowed to cool, and the moment liquid is drawn into the capillary tube, the temperature is the
compound's boiling point.

Lisa Nichols 10/18/2020 6.2B.2 CC-BY-NC-ND https://chem.libretexts.org/@go/page/95736

 Figure 6.22: a) Thiele tube apparatus, b) Students perform the boiling point technique in the hood.
This method utilizes the definition of boiling point: the temperature where the compound's vapor pressure equals the applied
(atmospheric) pressure. The inverted capillary tube acts as a reservoir to trap the compound's vapors. As the apparatus is
heated, the air initially trapped in the capillary tube expands and causes bubbles to emerge from the tube (Figure 6.23b). With
further heating, the compound's vapors eventually displace all of the trapped air, which is why heat is applied until there is a
continuous stream of bubbles.
When the apparatus is cooled, eventually the pressure inside the capillary tube (due solely to the compound's vapors) will
match the atmospheric pressure, at which point the bubbles will slow and liquid will be drawn into the tube. The temperature
where this begins is the compound's boiling point (Figure 6.23d).

Figure 6.23: Boiling point determination: a) Initial setup, b) After heating past the boiling point, c) Cooling, d) Liquid just
enters the capillary tube (temperature is the boiling point), e) Liquid is inside the capillary tube (temperature is lower than the
boiling point).

Thiele Tube Procedure

Lisa Nichols 10/18/2020 6.2B.3 CC-BY-NC-ND https://chem.libretexts.org/@go/page/95736

 Figure 6.24: a) Thiele tube, with arrow indicating the minimum height of oil, b) Tube attached to the thermometer with a
rubber band, c) Addition of sample, d) Insertion of the capillary tube.
1. Obtain a Thiele tube and clamp it to a ring stand in the fume hood (Figure 6.24a). The tube is normally filled with clear
mineral oil, but it may have darkened from oxidation or spilled compounds. If the oil is quite dark, it should be replaced.
The oil should be filled to at least 1 cm higher than the top triangular arm (an appropriate oil level is indicated in Figure
6.24a), and if too low the oil will not circulate as needed (Figure 6.25c).
2. Insert a thermometer into a one-holed rubber stopper with a slit down one side. Attach a small glass vial ("Durham tube",
or 6 x 50 mm culture tube) to the thermometer with a small rubber band (Figure 6.24b). The bottom of the vial should be
flush with the bottom of the thermometer.
3. Fill the vial about half-full with sample, which will require between 0.25-0.5 mL of sample (Figure 6.24c).
4. Insert a capillary tube into the sample (the same type that is used for melting points), open end down and sealed end up
(Figure 6.24d).

Figure 6.25: a) Insertion of the assembly into the Thiele tube, b) Rubber band is above the oil, c) Heating, d) Vigorous
bubbling of sample.
5. Place the rubber stopper and thermometer assembly into the Thiele tube, adjusting the height so that the sample is midway
(if possible) inside the tube (Figure 6.25a). The rubber band should be higher than the top of the mineral oil (Figure 6.25b),
keeping in mind that the oil may expand somewhat during heating. The thermometer should not touch the sides of the
glass, and if it does it should be clamped in such a way that it no longer touches.
6. Heat the oil gently on the side arm of the Thiele tube with a microburner if available, or Bunsen burner using a back and
forth motion (Figure 6.25c). As the oil warms and becomes less dense, it will rise and travel up the triangular portion of the
tube. The cooler, denser oil will sink, thereby creating a current as shown in Figure 6.25c). This method is an excellent way
to indirectly and slowly heat the sample.
7. Although bubbles should not be seen in the Thiele tube as it warms, they commonly are seen if the tube had been used
previously for boiling point determinations. In this method, the rubber band occasionally breaks causing the sample to fall
into the oil and contaminate it. If the oil is not subsequently changed, the sample may boil when heated in the tube. It is
okay to continue heating a Thiele tube if bubbles are seen.

Lisa Nichols 10/18/2020 6.2B.4 CC-BY-NC-ND https://chem.libretexts.org/@go/page/95736

 8. Studies of this method have determined that it is best to heat the oil gently and in a continual manner, as stopping and
7

starting have caused the results to suffer.

9. Continue heating until a vigorous stream of bubbles emerges from the tip of the capillary tube (Figure 6.25d), such that
individual bubbles can barely be distinguished. The purpose of this step is to expunge the air originally present in the
capillary tube and replace it with the sample's vapor. Do not heat so vigorously that the entire sample boils away. when
bubbles are vigorously emerging from the capillary tube, the vapor pressure inside the tube is greater than the atmospheric
pressure (the oil is at a higher temperature than the boiling point).
10. Turn off the burner and allow the apparatus to cool. The bubbles will slow and eventually stop. At some point the vapor
pressure inside the capillary tube will equal the atmospheric pressure and liquid will be drawn into the tube. The boiling
point should be recorded as the temperature when liquid just begins to enter the capillary tube (Figure 6.26b).

Figure 6.26: Time-lapse entry of liquid into the capillary tube. The boiling point should be recorded as the temperature at b).
11. Record the atmospheric pressure along with the boiling point.

Thiele Tube Summary

Table 6.3: Procedural summary for obtaining a boiling point.

Insert the sample into a Thiele

Fill a small tube about half-full Remove the heat and allow the oil
tube, so that the sample is near the Heat until a vigorous stream of
with sample and insert a capillary to cool.
middle of the oil. bubbles emerges from the capillary
tube, closed end up. The boiling point is the
Heat the arm of the Thiele tube tube, such that individual drops
Attach the tube to a thermometer temperature when the oil just
with a burner, gently and can be barely distinguished.
with a small rubber band. begins to enter the capillary tube.
continuously.

5
The author found the boiling point of ethanol to be 76 o
C (765 mm Hg) with distillation (literature boiling point is 78 o
C .
6
The author found the boiling point of ethanol (literature boiling point of 78 C) to be 77.2 C with the microscale condenser
o o

setup and 76 C with the test tube reflux setup (765 mm Hg). Note: Different thermometers were used with each method.
o

Lisa Nichols 10/18/2020 6.2B.5 CC-BY-NC-ND https://chem.libretexts.org/@go/page/95736

7
Blank, E. W., Ind. Eng. Chem. Anal. Ed., 1933, 5(1), p 74-75.

Contributor
Lisa Nichols (Butte Community College). Organic Chemistry Laboratory Techniques is licensed under a Creative
Commons Attribution-NonCommercial-NoDerivatives 4.0 International License. Complete text is available online.

Lisa Nichols 10/18/2020 6.2B.6 CC-BY-NC-ND https://chem.libretexts.org/@go/page/95736