Na168vx2 Service Manual

Order No.
WMH1002151CE
Drum Type Washing Machine
NA-168VX2 NA-128VA2
NA-168VG2 NA-147VB2
NA-148VA2
Product Colour :White
Destination :Germany, United Kingdom, France, Spain,
Italy, Holand, Belgium, Sweden, Norway, Denmark,
Poland, Czech, Hungary, Romania, Malaysia,
Indonesia
! WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service
or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.
IMPORTANT SAFETY NOTICE

There are special components used in this equipment which are important for safet y. These par ts are marked by ! in the Schematic
Diagrams, Circui t Board Diagrams, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced
with manufacturer's specified part s to prevent shock, fire or other hazards. Do not modify the orig inal design without permission of
manufacturer.
CONTENTS
Page Page
1 SPECIFICATIONS 2 9 WIRING DIAGRAM 19
2 PRODUCT INFORMATION 3-8 10 CHECK INPUT AND OUTPUT VOLTAGE OF THE PC.BOARD
3 KNOW THE WASHING MACHINE 9 20-21
4 MOVING AND INSTALLING 10-14 11 TROUBLESHOOTING GUIDE 22-23
5 HOW TO ADD DETERGENT AND SOFTENER 15 12 OPERATING TEST-NO WATER 24-25
6 MAINTENANCE 16 13 ERROR DISPLAY 26-27
7 USING THE BUTTONS 17 14 DISASSEMBLY INSTRUCTIONS AND ADJUSTMENTS 28-38
8 DETAILS OF PROGRAMMES 18 15 LOCATION OF PARTS 39-48
C Panasonic HA Washing Machine Hangzhou 2010.

All rights reserved. Unauthorized copying and
distribution is a violation of law.
Downloaded from www.Manualslib.com manuals search engine

1 SPECIFICATIONS
Model No. NA-168VX2 NA-168VG2 NA-148VA2 NA-128VA2 NA-147VB2
Power source AC220V-240V/50Hz AC220V-240V/50Hz AC220V-240V/50Hz AC220V-240V/50Hz AC220V-240V/50Hz
Product weight 85kg 85kg 85kg 85kg 85kg
Dimensions(W*D*H)(mm) 596*625*845 596*625*845 596*625*845 596*625*845 596*625*845
Laundry capacity 8.0kg 8.0kg 8.0kg 8.0kg 7.0kg
Body Colour White White White White White
Operation Panel Dial+LCD Dial+LED Dial+LED Dial+LED Dial+LED
Drum(Wash) r/min .(Rated load) 37 53 r/min. 37 53 r/min. 37 53 r/min. 37 53 r/min. 37 53 r/min.
Spin r/min. (Rated load) Max: 1600rpm. Max: 1600rpm. Max: 1400rpm. Max: 1200rpm. Max: 1400rpm.

Washing Variable Rotation Control
Performance Wide Angle Water Supply Shower
Process & Cloth load Indicator - - - -
Washing Program 12 12 12 12 12
Energy Consumption Below 1.19kWh Below 1.19kWh Below 1.19kWh Below 1.19kWh Below 1.19kWh
Super quiet by Inverter- Super quiet by Inverter- Super quiet by Inverter- Super quiet by Inverter- Super quiet by Inverter-
Controlled brushless Controlled brushless Controlled brushless Controlled brushless Controlled brushless
Noise level Motor Motor Motor Motor Motor
NA-168VX2/168VG2/148VA2/128VA2/147VB2
-2-
Easy to take-out laundry Tilted 10O Drum Tilted 10 O Drum Tilted 10O Drum Tilted 10 O Drum Tilted 10O Drum
Lid Open One Push Button One Push Button One Push Button One Push Button One Push Button
Maximum power consumption 2075W-2350W 2075W-2350W 2075W-2350W 2075W-2350W 2075W-2250W
Heating power consumption 2000W/230V 2000W/230V 2000W/230V 2000W/230V 2000W/230V
Pressure of tap water 0.03-1Mpa 0.03-1Mpa 0.03-1Mpa 0.03-1Mpa 0.03-1Mpa
Cotton Cotton-Eco Cotton Cotton-Eco Cotton Cotton-Eco Cotton Cotton-Eco Cotton Cotton-Eco
Quick60 Rapid 15 Quick60 Rapid 15 Quick60 Rapid 15 Quick60 Rapid 15 Quick60 Rapid 15
Ease-care Wool/Silk Ease-care Wool/Silk Ease-care Wool/Silk Ease-care Wool/Silk Ease-care Wool/Silk
Course select 15 Wash Memory 15 Wash Memory 15 Wash Sportswear 15 Wash Sportswear Delicates Shirts
Sportswear Shirts Sportswear Shirts Shirts Baby-care Shirts Baby-care Bedding Colours
Bedding Colours Bedding Colours Bedding Colours Bedding Colours Quiet Tub clean
Cold 30 40 Cold 30 40 Cold 30 40 Cold 30 40 Cold 30 40
Temperature 50 60 70 60 90 60 90 60 90 60 90
80 90
Cycle-end buzzer, Cycle-end buzzer, Cycle-end buzzer, Cycle-end buzzer, Cycle-end buzzer,
Buzzer Beeper alarm Beeper alarm Beeper alarm Beeper alarm Beeper alarm
U appears 5 items U appears 5 items U appears 5 items U appears 5 items U appears 5 items
Error display H appears 18 items H appears 18 items H appears 18 items H appears 18 items H appears 18 items
Cover cap Spanner Cover cap Spanner Cover cap Spanner Cover cap Spanner Cover cap Spanner
Accessories
Elbow Elbow Elbow Elbow Elbow
NA-168VX2/168VG2/148VA2/128VA2/147VB2
2 PRODUCT INFORMATION
2-1 New Drum washing machine Tilted Drum
The drum shall be tilted to save water and increase easy operation.
Compared to the Horizontal drum type, Tilted drum can save water.
When put laundry into the drum and take out laundry easily from the drum after washing. It is called
Universal design .
And also, the door can be opened easily by pressing the door button.
Horizontal drum type Tilted drum
2-2 Produce high washability

Condensed foam shall be produced at bottom portion of the outer tub unit when the drum rotating at the initial
stage of the wash cycle. This condensed foam will taken the soil from the laundry very effect ively. Splashed water
shall be showered from the upper portion of the outer tub, and also dissolved detergent showered from three baffles
on the drum.
Shower from the upper portion

Foam wash Shower from the baffle + Whirling
+ Whirling
Shower
Shower
Foam
2-3 Model
On model NA-168VX2
-3-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
2-3-1 Optional Washing Settings

Intensive Extra Rinse Prewash Easy Ironing
Conducts a more Adds an extra Add a pre-wash Prevent wrinkles caused by

thorough wash rinse cycle to cycle to the tangling.
that lasts 10 or 20 ensure that all ordinary course. Once the spin cycle completes,
minutes longer detergent is the machine intermittently
than normal. removed. Ideal for heavily comes on and the drum rotates
soiled items. to loosen garments.
Ideal for heavily Ideal forbabies This mode gently spin-dries
soiled laundry with delicate skin shirts and other items that tend
such as or anyone to wrinkle easily.
sportswear with concerned about
tough stains. allergies.
2-3-2
For 168VX2(LCD Display)
Process & Cloth Load Indicator
*Cloth load indicator (after push start button) Child Lock & Door Lock
*Process indicator (during washing process) Indicator
Process Select
Water Temperature Setting Delay Start Setting *Wash+Rinse+Spin
*90 *80 *70 *60 *50 & Remain Time Indicator *Rinse only
*40 *30 *Cold *Spin only
Spin Speed Setting *Wash+Rinse
*1600r/min*1400r/min *1200r/min*1000r/min *Rinse+Spin
*800r/min*700r/min*600r/min*500r/min *400r/min *Drain only
For 168VG2, 148VA2/147VB2, 128VA2(LED Display)

Example Display on NA-168VG2
Child Lock & Door Lock Indicator
Process Select
Water Temperature Setting Delay Start Setting
*Wash+Rinse+Spin
*90 *60 & Remain Time Indicator
*Rinse only
*40 *30 *Cold
*Spin only
Spin Speed Setting *Wash+Rinse
(168VG2) *1600r/min *1200r/min *800r/min *500r/min *Rinse+Spin
(148VA2/147VB2) *1400r/min *1200r/min *800r/min *500r/min *Drain only
(128VA2) *1200r/min *1000r/min *800r/min *500r/min
-4-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
2-3-3 Programme
For NA-168VX2/168VG2
For NA-148VA2/128VA2
For NA-147VB2
2-4 How to turn the "end of programme" buzzer on or off

Start
Pause
1 Press the START and power ON buttons at the same

time,
On
Start
Pause
2 and keep pressing the START button for at least
three seconds.
2-5 Wide angle water supply shower

New method (Conventional Supply + Wide-Angle Water Supply Shower)
Benefit of Wide-Angle Water Supply Shower
Washing Quick Water
Process
Penetration Effect
High Beating Wash and
Save The Time
Rinsing Water Supply Shower

Process
During Rinsing Process
Fine Rinsing Effect and
Save The Time
-5-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
2-6 Smart Beat Wash by variable rotation control

Previous washing method
The drum rotates at a constant speed. Therefore, due to different fabrics and weights of clothing
and insufficient penetration of water, dirt can not be beaten out by washing.
If clothes shall not be
Heavily clothes Lightly clothes penetrated water enough
45 r/min 45 r/min 45 r/min
New washing method (Variable rotation control)

, 3D Sensor
The laundry s movement inside the drum shall
be detected by 3D sensor, and the drum rotates
most suitable speed to realize proper beat washing.
If clothes shall not be

Heavily clothes Lightly clothes penetrated water enough
Increased rotation Decreased rotation Decreased rotation

speed of the drum speed of the drum speed of the drum
How to check the 3D sensor

Operate "Test-No water"
C-process: Spin Operation
Operate approx. 2 minutes with no load

(it shall be rotated smoothly)
1)Press / temp. switch =X-axis If indicate below 30 (Actual
2)Press r/min (spin) switch =Y-axis moving 3mm)
3)Time (Reserve) switch =z-axis If indicate more than 30
Incase there is no data and signal coming from the

3D sensor to the main PC Board within 30 seconds Replace the 3D sensor
H41 shall be appeared.
-6-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
2-7 Safety
Leak-proof System
This system is designed to prevent water leaks from the washing machine, and includes
the following components:
Water Supply Valve

Water Hose Valve Detect water leakage, stop water
supply at product side.
If the water hose is damaged,
detect water leakage and stop
water supply at the tap side.
Filter Valve
Interlocking Detect the opening and closing
condition of drain filter,
prevent coming out the water.
Water Leakage Sensor
Premium Deluxe Standard

NA-168VX2 NA-168VG2 NA-148VA2 NA-128VA2 NA-147VB2
Water Supply Valve Yes Yes Yes Yes Yes
Filter Valve Yes Yes Yes Yes Yes
No No No No
Water Hose Valve Yes (Germany/
France:Yes) (Germany:Yes) (Germany:Yes) (Germany:Yes)
2-8 Switching Sensor Panasonic

Other brands
Drain Filter
valve
Interlocking
Drain filter
When "Drain filter" is opened during the operation, When "Drain filter" is opened ,Filter valve closes
water in the drum comes out. automatically by sensing the filter condition
in order prevent from coming water.
-7-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
2-9 How to lock or unlock the door

The door is automatically locked while any programme is running. sign is shown
while the door is locked.
Caution
To unlock the door while a programme is running

During operation After the drum stops spinning, the door will automatically unlock and will be
Start signaled with a clicking sound. This can take about a minute.
Pause * If you have to unlock the door mid-programme, try to make sure you don't
Press flood the floor with water from the drum.
2-10 How to set and reset the child safety lock

The child safety lock prevents children climbing into the washing machine drum and getting trapped.
It keeps the door closed and locked even when the washing machine is not in use.
It also locks the control buttons.
1 Switch the washing machine on.
2 Press and hold the MODE button for five seconds or more.
(The sign lights to confirm the child safety lock is active.)
1 * On model NA-168VX2
2-11 Release the door lock for servicing

Incase the locked by breaker cut off or power outage.
Push the small hole between the door

and body B by pin, and press the
push button to open the door.
-8-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
3 KNOW THE WASHING MACHINE

3-1 Component Name
(On model
NA-168VX2
only)
(Push the door opening

button and open by holding
the right side of the door)
Do not fold the

mains lead when
the washing
machine is running.
Drain filter
cover
-9-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
4 MOVING AND INSTALLING

4-1 Carrying the washing machine
Two or more people must carry the washing machine.
Start by tilting the washing machine backwards. One person
should stand behind it, holding the rear of the top panel.
The other person should grip the bottom stands at the front.
Don't touch the door opening button while holding.
Make sure of the needed accessories for installation.
Entrust the installation of the product to our dealer or
service agent.
4-2 Removing the anchor bolts
washing
To remove the anchor bolts:
A B
You'll need the anchor bolts again if you move the washing machine, so make sure you
keep them safe. And if the washing machine passes to someone else, make sure you give
them the anchor bolts.
4-3 Moving the washing machine from one location to another

Make sure to fix the anchor bolts for transportation to the washing machine.
Before you move the washing machine
Shut the tap and run the washing machine to drain the water. Drain any remaining water from the pump hose.
Depressurise the water-supply hose and remove it.
Disconnect the power cable.
Attach the anchor bolts .
4-4 Attaching the anchor bolts

Unscrew and remove the four cover caps.
Pull the bolts out, so their tips are level with the tips of the
sleeves.
(Ask someone else to hold the upper surface of the drum and
pull it forward.)
Insert the transportation guards 1, 2, 3 and 4.
Tighten each bolt.
Tighten the bolt so that spring length becomes 26mm.
-10-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
4-5 The right place for washing machine
Sloping Unstable Bumpy

Surface Surface Surface
Other things to avoid:
4-6 Washing machine dimensions in millimetres

240
845
582 516 38
596 594
625
4-7 Installing a built-in washing machine
Metal cover Separately sold accessories

Metal cover
(AXW4595-7FH0)
(AXW4595-7KG0) (WHITE)
-11-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
How to adjust frequency of the water level detector

Note: The operation method for NA-147VB2 is same as NA-16VX1 series.
Part No. : AXW4595-7FH0

AXW4595-7KG0 Changed to the metal cover to built-in
Description: Metal cover
When you install the metal cover instead of the top board for built-in the washing machine, it is
necessary to adjust frequency of the water level detector with below procedure to supply proper
water volume against laundry amount.
1. Press the power ON button.
2. Turn the Programme Selection knob to

"Wool/Silk course" position.
3. Press the time button more than 3

seconds.
(For 168VX2, the sign "0 000" lights to
confirm the mode is active)
(For 168VG2/148VA2/128VA2, the sign
"30 000" lights to confirm the mode is
active)
4. Press the button once.

(For 168VX2, the sign "1 000" lights to
confirm the mode be changed)
(For 168VG2/148VA2/128VA2, the sign
"40 000" lights to confirm the mode be
changed)
5. Press the Start / Pause button.

The click sound shall be rung, and turn it OFF
automatically.
-12-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
4-8 Hose and Cable Lengths
105 135
130
100
4-9 Levelling the washing machine

Using a level facilitates the adjustment.
When adjusting the washing machine to make it level, ensure all four stands are supporting it:
On each stand, loosen the lock nut by turning it clockwise using the
A end of the spanner supplied.
Adjust all four stands in this way.

Lock nut Use a spirit level to ensure the washing machine is standing correctly.
Stand Tighten each lock nut by turning it anti-clockwise (towards the
washing machine body), again using the A end of the spanner
supplied.
Ensure all four lock nuts are tightened securely.

Check the stands are still bolted to the washing
A B
machine - if they're unbolted, the washing
machine will move around.
To adjust the stands, use A side of the included spanner.
4-10 Water-supply hose
Points to remember:
Don't twist, squash, modify or cut the hose.
Optimum water pressure in the main pipe is 0.03 MPa - 1.0 Mpa.
If the pressure is set higher than this, you'll need to install a depressurising valve.
Water-flow from the tap should be more than 5 litres per minute.
Connecting the water-supply hose
Attach the hose to a tap, and tighten
1 the plastic joint by hand. min. 10 mm min. 10 mm
Plastic joint
2 Open the tap slowly and check there
are no leaks around the joint. Hose with water- Standard hose
Caution: the joint is subject to water pressure. supply valve
-13-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
4-11 Water drain hose

Points to remember:
Do not twist, pull out or bend the drain hose.
The machine should be no more than 100cm from the drain outlet.
Draining to a sink or wash-basin:
Elbow
Draining to a wash-basin Draining to a drain hose

4-12 Installation checklist
Anchor bolts-have you removed them, and attached the cover caps properly?
Location-is the machine on a flat, stable surface? Does it run without vibrating?
Water-supply hose-is it free from leaks, and is the water supply normal?
Water-drain hose-is it free from leaks, and does it drain normally?
Four adjustable stands-are they bolted securely to the washing machine?
Four stand cushions-are they standing flat?
There may be abnormal sounds while dewatering if it is not set flat.
Power supply-is the household dedicated mains socket, fully rated at AC 220V to 240V independently?
4-13 Test run after installation
8:88
0:03
-14-

5 HOW TO ADD DETERGENT AND SOFTENER
Only use detergents recommended for fully-automated washing

machine. Refer to the instructions on the packaging for appropriate
amounts to use for different wash programmes.

Softener
Water softening agent

(strongly recommended in hard
-15-
water areas)
* If you live in a hard water area, we recommend
use of a water softening agent to soften the water.
* Always check the packaging for the
appropriate amount to use.
* Always add your water softener after your detergent.
* Use of a water softening agent can help reduce
Theamount of detergent required for each wash.
and it will help to prevent the formation of
limescale deposits which may damage the
machine.
Do not use washing machine,

when remove the detergent
drawer.
(It may cause a water leak or
it may not work normally)
If the instructions on the package indicate that gel detergent or liquid detergent
Add tub cleaning detergent or bleach to this tablets should be placed in the drum, do not put them into the detergent
compartment. drawe r. These detergents may not flow well and remain in the detergent drawer.
NA-168VX2/168VG2/148VA2/128VA2/147VB2
NA-168VX2/168VG2/148VA2/128VA2/147VB2
Max 6L)
6 MAINTENANCE
-16-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
Pause
Start
7 USING THE BUTTONS
-17-

8 DETAILS OF PROGRAMMES Times depend on programme and temperature settings selected.
Times may be longer if the laundry in the drum needs to be balanced.

NA-168VX2/168VG2/148VA2/128VA2/147VB2
-18-
#
#
-19-
BLACK
PURPLE
YELLOW
Feed
Valve 2
Filter
BROWN-WHITE
YELLOW
Feed
BROWN
GREEN-YELLOW
Noise LIGHT-BLUE
GRAY
YELLOW
Feed
WHITE YELLOW
ORANGE WHITE-ORANGE
Feed
Heater
Valve AQUA Valve 1 Valve 3
9 WIRING DIAGRAM
BROWN
BROWN YELLOW-WHITE
RED YELLOW-RED
Motor
PURPLE
Door lock
BLUE
WHITE RED-WHITE
WHITE BLUE-WHITE
Reactor
Door lock 2/2
GRAY
GRAY
Motor
YELLOW-BLACK
temperature
LIGHTBLUE-BLACK
ORANGE-WHITE
ORANGE-WHITE
Door detection Switch A
Door detection Switch B
Motor
tachogenerator PINK
PINK-WHITE
Pressure
sensor unit
YELLOW-BLACK
BLACK
YELLOW-BLACK
TH4
BLUE
YELLOW
BROWN
water temperature
GREEN
ORANGE
3D sensor
RED
PINK
WHITE
PINK-BLACK WHITE
WHITE
Filter sensor
WHITE
WHITE
BLACK WHITE
RED WHITE
WHITE
WHITE
Controller Unit A
WHITE
WHITE
ORANGE
WHITE
BLUE
WHITE-BLUE BLUE
Water
YELLOW
Leak sensor
WHITE-RED
Cooling fan Pump Drain valve

NA-168VX2/168VG2/148VA2/128VA2/147VB2
10 CHECK INPUT AND OUTPUT VOLTAGE OF THE PC BOARD
10-1 1. Before replace PC Board, check input and output voltage of the PC Board.
2. Check range of the test meter.
3. When check output voltage of the PC Bord, set a program of the Washing Machine on the working mode.
AC 220V AC 220V AC 220V
4.8K 4.8K 180
Feed Feed Door detection Switch A Controller Unit A
Valve 2 Valve 1 Pump Door lock Door detection Switch B (1/2)
ALL WHITE
WHITE
PURPLE
YELLOW
YELLOW
GRAY
ORANGE
Door lock 2/2 Filter sensor
AC 220V AC 220V AC 220V Room Temp. Resistance
4.2K 4.8K 6K 15 DC12V
Feed Feed

Pressure 0 Approx.9.7k
Valve AQUA Valve 3 Drain valve sensor unit 3D sensor Cooling fan
10 Approx.5.7k
PINK
RED
BLACK
WHITE
BLACK
YELLOW
YELLOW
YELLOW
BROWN
ORANGE
AC 220V
WHITE-RED
RED-WHITE
PINK-WHITE
WHITE-BLUE
BLUE-WHITE
20 Approx.3.7k
YELLOW-RED
LIGHTBLUE-BLACK
WHITE
Input
BROWN-WHITE
YELLOW-WHITE
YELLOW-BLACK
YELLOW-BLACK
YELLOW-BLACK
WHITE-ORANGE
PINK-BLACK
Voltage
RED
30 Approx.2.3k
GREEN
BLUE
YELLOW
PINK
NA-168VX2/168VG2/148VA2/128VA2/147VB2
WHITE RED
LIGHT-BLUE
-20-
WHITE RED WHITE RED WHITE RED RED L.BLUE
BLUE
Water leak sensor
ORANGE BLUE
BROWN BLUE
ORANGE
WHITE WHITE
WHITE
WHITE WHITE
Controller Unit A
WHITE (1/2)
WHITE
WHITE
GRAY
GRAY
ORANGE-WHITE
ORANGE-WHITE
BROWN
BROWN
RED
PURPLE
BLUE
BROWN
LIGHT BLUE
WHITE
ORANGE
Motor
Motor tachogenerator
Noise
Filter Heater <Method to check the motor>
BLACK AC 220V The resistane of the each terminal of the
Reactor
26 Motor
temperature motor shall be shown on next page.
NA-168VX2/168VG2/148VA2/128VA2/147VB2
10-2 Motor (Brushless type)

Rotation speed: Inverter control
Quiet operation: Below 55 dB
Structure: Simple & Less-trouble
W
Y <Rated resistance>
- Coil Approx. 3.2
- Coil Approx. 3.2
Z
U V - Coil Approx. 3.2
X
Thermistor Approx. 11.4K at 20
WHITE
RED - Tachogenerator Approx. 113
GREY
THERMISTOR - Thermal protector Approx. 0
BROWN
RED
7 8 9 10 11 12
1 2 3 4 5 6
RED PINK
T PROTECTOR
RED LIGHT BLUE
-21-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
11 TROUBLESHOOTING
(NA-147VB2 only)
-22-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
-23-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
12 OPERATING TEST-NO WATER

Method to "Operating Test- No Water"
* On mode NA-168VX2
1. Press the power switch to "OFF".

2. Press and hold both the "Intensive" and"Extra Rinse" buttons with one hand.
3. Press the power switch to "ON".
4. Release your fingers from the buttons and power switch you pressed in step (2) and (3) above.
(Check mode-A shall be carried out with your fingers released.)
5. Press the "Intensive" button within 3 seconds to the desired check contents .(Carry out check B,C,I,G and H)
0 A 888
1 B 6
2 C 7
3 I 8
4 G1
-24-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
5 G2 E2
6 G3 E3
7 H C
-25-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
13 ERROR DISPLAY
(Incase of U11) U
Indication Contents Detect contents Check point Method to clear
Unable to drain Incase won't detect
U reset point in 12 min.
Is something wrong with the drain hose?
Is lint clogging it?
After solving proble-
ms, open the door
After starting of drain. Check if condition of the water level detector. and close it, and
then restart
operation.
U 2 The door is
open
Door is opening at start
point of the operation.
Is the door open? Close the door to
start operation.
After solving proble-

U 3 Unbalanced
load
Detect unbalanced
load at spin process.
Chack if clothes are not tangled in the drum.
Check if the washer is not installed on an unstable or
ms, open the door
and close it, and
sloping floor. then restart
operation.
Unable to It's takes over 20 min. It's takes over 20 min. to reach specified water level.
U 4 supply water to reach specified water Check if condition of the water valve.
After solving
problems, open the
level. Is the filter of the feed valve clogged? door and close it,
and then restart
operation.
Drain filter is Detect drain filter is Check if drain filter is securely tightened during the
U 8 not set securely tightened operation. Set the drain filter
properly
Water level Input frequency from the Check if condition of the connectors.
h0 detector water level detector is Replace water level detector. Turn off the power
out of rated frequency. Replace PC Board (Power side).
Replace PC Board. Remove the power

h04 Short circuit of
power relay on
Detect short circuit of
the power relay on the plug
the PC.Board PC Board.
Replace PC Board (Power side). Turn off the power

h05 Data shall not
be memorized.
Data won't saved to the
micro processor(In case Effected service mode (Check mode-B) only.
of service check mode-B).
Check if condition of the connector and lead wire of Turn off the power
h07 Malfunction of
rotary detector.
Input signal from the
rotary detector when the rotary detector.
operating the motor Replace the motor.
shall be occurred out of Replace the PC Board (Power side).
standard.
Check if lead wire condition of PC Board between Remove the power

h09 Open circuit of
the PC Board's
Won't communicate
between the main micro power and operation side, and replace one of PC plug
communication processor and the Boards.
line indication micro
processor.
Check if condition of the connectors.

h 7 Open circuit or
short circuit of
Detect abnormal signal
from the thermistor TH4 Replace the thermistor TH4
Turn off the power
the thermistor
TH4
-26-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
Indication Contents Detect contents Check point Method to clear

Open circuit or Detect abmormal signal Turn off the power
H 8 short circuit o from the motor
Check if condition of the motor s connector.
Replace the motor.
the motor thermistor TH5
thermistor TH5
Water shall be Water level detector Clean the diaphragm inside of the feed valve or Turn off the power
H2 leaked from
the feed valve
detect increasing of
water level.
replace the feed valve.
* Operate the Geared motor and the drain pump to
drain water.
Open circuit or Detect abnormal signal Replace PC.Board(Power side) Turn off the power
H23 short circuit of
the heater relay
of the Heater Relay
Open or short Geared motor won't Check if condition of the connector for the Geared Turn off the power
H25 circuit of the
Geared motor
operate even operating
position
motor.
Replace the Geared motor.
Replace the PC.Board (Power side).
Malfunction of Door lock switch won't Check if condition of the connector for the door lock
H27 the door lock operate even operating switch.
Turn off the power
switch. position. Replace the door lock switch.

Replace the PC.Board (Power side).
Decreased Rotation speed of the Check if condition of the connector for the cooling fan.
H29 rotation speed cooling fan shall be Replace the cooling fan.
Turn off the power
of the cooling decreased below Replace the PC Board(Power side)

fan 1200r/min
Acceleration During spinning Replace the 3D sensor.

H4 data shall not acceleration data shall Replace the PC Board(Power side).
Turn off the power
be alterated not be obtained or

alterated
Water shall be Water leak detector Check if water leakage from the hoses and joint
H43 leaked inside of detct water on the portions inside of the washing machine.
Turn off the power
the washing botton plate

machine
Open or short Detect abnormal signal Replace PC Board(Power side)

H46 circuit of the from the water leak
Turn off the power
water leak detector.

detector
Supplied Measured input voltage Check input voltage to the washing machine.
H52 abnormal high (20% higher against
Turn off the power
voltage rated voltage).
Supplied Measured input voltage Check input voltage to the washing machine.
H53 abnormal Low (20% Lower against
Turn off the power
voltage rated voltage)
High current Detect abnormal high Replace the PC.Board(Power side)

H55 signal shall be current signal during
Turn off the power
flowed during motor rotation

motor rotation
-27-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
14 DISASSEMBLY INSTRUCTIONS AND ADJUSTMENTS

Description Figure Procedure
1 Replacement of 1.Remove the three screws mounting the upper
the upper board board.
2.Hold and slide the upper board arrow direction

as shown in left figure, and pull it up to remove.
Slide
2 Replacement of After remove the upper Board,

the PC Board 1.Remove the two screws mounting the PC Board
w/components for for power side.
Power side 2.Remove the two screws mounting the earth wires
from the PC Board.
3.Up side down the PC Board.

4.Remove the three screws mounting the steel
cover.
5.Remove the one connector of the fan motor and

remove the steel cover.
6.Remove all the connectors and the three lead
wire holders
from the PC Board for power side, and remove
lead wires.
Note:
8-pins red colour connector case may remain,
please note, this connector is not using.
3 Replacement of After remove the upper board,
the 3D sensor 1.Remove the two screws mounting the 3D sensor.
2.Loosen the two lead wire holders, remove tape
and the insulation cover.
-28-

NA-168VX2/168VG2/148VA2/128VA2/147VB2

3.Remove the two lead wire holders and the one
connector to remove the 3D sensor.

the water level 1.Push the one pawl to outward as shown in figure,
detector and pull the water level detector upward.
2.Remove the connector and sub hose A from the

water level detector.
3.Remove the water level detector.

the feed valve 1.Remove the four screws mounting the detergent
case A.
2.Remove the two screws and the two pawls

mounting the pressure hose case.
3.loosen the nut from the feed valve unit by using

the spanner.
-29-

NA-168VX2/168VG2/148VA2/128VA2/147VB2

4.pull all pawls up to remove the detergent case A
from the body joint.
5.Remove the two screws mounting the feed valve

unit as shown in left figure.
6.Remove the three connectors from the feed valve

unit, and pull it out to remove by a screwdriver.

the PC Board for 1.Remove the detergent case B, and remove the
operation one screw mounting the panel face board.
2.Remove another screw mounting the panel face

board.
3.Press all pawls mounting the panel face board

and pull it out slightly to remove.
-30-

NA-168VX2/168VG2/148VA2/128VA2/147VB2

5.Remove the one lead wire holder from the PC
Board.
6.Turn the PC Board up, remove the five screws

and the seven pawls mounting the PC Board,
and remove the PC Board cover.
Note:
Please spread a cloth on to the washine machine
to prevent scratch on the surface of the panel face
board.
7.Remove the two connectors from the PC Board

for power side. (See page-28 replacement of
the PC Board for power side)
8.Remove the PC Board for operation.
Note:
Connector of the PC Board for operation shall be
inserted to the main PC Board(for power side).
7 Replacement of 1.After opening the door unit, remove the three

the door unit screws mounting the door unit.
2.Hold and pull the door unit upward to remove.
8 Replacement of 1.After remove the door unit and the PC Board,

the body band A remove the seven seals covering the screw of
the Body band A with mini-screwdriver.
-31-

NA-168VX2/168VG2/148VA2/128VA2/147VB2

2.Remove the seven screws mounting the body
band A.
3.Remove the body band B.
4.Take out the body band A.
9 Replacement of After remove the door unit, and the body band A,
the door lock 1.Remove the two screws mounting the door lock
switch switch.
2.Loosen the lead wire holder, remove the tape
and the insulation cover.
3.Remove the two connectors to remove the door

lock switch.
10 Replacement 1.Remove the two screws mounting the door button.

of the door button 2.Remove the hook from the door lock switch.
-32-

NA-168VX2/168VG2/148VA2/128VA2/147VB2

11 Replacement 1.Open the filter cover.
of the panel A 2.Remove the two screws mounting the panel A.
3.Remove the hose out from the hose holder.
4.slide the panel A to left slightly to remove as

shown in left figure.
Slide
12 Replacement After remove the panel A,

of the body B 1.Remove the body band B by long nose pliers.
2.Remove the wringer frame packing(Made of

rubber) from the body B.
3.Remove the eight screws mounting the body B.
4.Unfix the lead wire holder at right portion.

5.Hold the body B and pull it up slightly to remove.
-33-

NA-168VX2/168VG2/148VA2/128VA2/147VB2

13 Replacement After remove the body B
of the wringer 1.Remove the body band B fixing the wringer frame
frame packing packing by using 2 long nose pliers.
2.Remove the wringer frame packing.

Note:
Incase to mounting the wringer frame packing A,
cutting portion shall be set to the marking portion
of the outer tub cover.
14 Replacement After remove the body B and wringer frame packing

of the balance 1.Remove 3 bolts by the spanner (size 10mm).
weight upper front 2.Pull out the Balance weight to remove.
15 Replacement After remove the body B and wringer frame packing,

of the balance 1.Remove the 3 bolts by the spanner (size 13mm).
weight lower front Note:
Use gloves in case to remove the bolts.
16 Replacement After remove the body B, wringer frame packing

of the outer tub and both balance weights
cover 1.Remove 3D sensor.(See page-28 replacement of
the 3D sensor)
2.Remove the shower hose, and the sub hose from

the detergent case A.
-34-

NA-168VX2/168VG2/148VA2/128VA2/147VB2

3.Remove the hose clamp from the outer tub, and
remove the feed hose A.
4.Remove the nineteen bolts mounting the outer

tub cover by a box wrench (size 10mm).
5.Pull out the outer tub cover to remove.
17 Replacement After remove the outer tub cover

of the drum unit 1.Remove the cap by using minus-type screwdriver.
2.Remove a screw mounting the drum cover.
3.Remove the drum cover.
4.Remove the six bolts mounting the drum unit by

the box wrench (size 13mm).
4.Pull out the drum unit to remove.
-35-

NA-168VX2/168VG2/148VA2/128VA2/147VB2

18 Replacement 1.Remove the two hose clamps and 2 hoses from
of the drain pump the drain pump.
2.Remove the three screws mounting the drain

pump.
3.Push the drum unit left slightly, and take the
drain pump unit out.
4.Remove the two covers and remove the three

connectors from the drain pump.
5.Remove the one screw mounting the switching
sensor, remove the switching sensor.
6.Remove the drain pump.
19 Replacement After lay down the washing machine on it left side

of the geared 1.Remove the four screws mounting the bottom
motor plate A, remove the bottom plate A.
Note:
Please spread a cloth to prevent scratch on the
body.
2.Remove the two bolts mounting the geared motor

by the box wrench (size 10mm).
3.Remove the one connector from the geared motor.
20 Replacement After lay down the washing machine on it left side

of the valve and remove the bottom plate A.
packing unit 1.Turn the valve lid to counter-clock wise.
2.Pull out the valve packing unit from the valve
frame.
Note:
Please spread a cloth to prevent scratch on the
body.
-36-

NA-168VX2/168VG2/148VA2/128VA2/147VB2

21 Replacement (TH4 detects water temperature in the drum)
of the thermistor-4 After lay down the washing machine on it left side
and remove the bottom plate A.
1.Remove the two screws mounting the thermistor-4.
Note:
Please spread a cloth to prevent scratch on the body.
2.Remove one connector from the thermistor-4.

3.Pull out the thermistor-4.
22 Replacement After remove the rear panel

of the heater unit 1.Remove the cover and the two connectors.
2.Remove one nut mounting the heater unit by the

box wrench (size 10mm) and remove a earthwire.
3.Release another nut slightly, and push the nut

inside by the box wrench, and pull it out to remove.
23 Replacement 1.Remove all screws mounting the rear panel.

of the belt 2.Remove the rear panel.
-37-

NA-168VX2/168VG2/148VA2/128VA2/147VB2

3.Turn the large pulley and remove the belt outward.
24 Replacement After remove the rear panel lay down the washing
of the Motor machine on it left side and remove the bottom
plate A.
1.Remove the insulation cover .
Method to fix the lead wire of the motor
connector portion: See page-39.
2.remove the connector.
3.Remove the two bolts mounting the motor by the

box wrench (size 10mm).
4.Pull out the motor.
25 Replacement After remove the rear panel

of the Pulley 1.Insert the two holes of the pulley with special tool
(Parts No. JF066), then loosen the nut with spanner
as shown in left figure .
2.Remove the belt.
3.Remove the nut and gasket.
4.remove the pulley.
-38-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
<Method to fix the Lead wire of the motor connector portion>
Lead wire holder
1) Lay down the washing machine. 3) Check condition of the lead wire holders
2) Remove the bottom plate A. (wire type).
Lead wire holder
4) Remove the lead wire holder (2portions). 5) Fix the lead wire holder (insulock block type)
on to the isolating tape portion temporarily.
Motor cover B
Insert from left
6) Insert the lead wire holder (insulock block 7) Clamp and fix the lead wire holder (insulock
type) in to the motor cover B from left side. block type) to the motor cover B, and cut the
surplus portion of the lead wire holder by pliers.
-39-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
15 LOCATION OF PARTS-A
-40-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
REPLACEMENT PARTS LIST-A

(U):U indicates parts at the remarks that can be replaced by user.
:Components identified by Mark have special characteristics important for safety.
When replacing any of these components use only manufacture's specified parts.
P :Indicates parts that are supplied by PPSC/Japan.
Ref. Q'ty 168VX2 168VG2 148VA2 128VA2 147VB2
No . Part No. Description Remarks
A01 AXW11NB7FH0 TOP BOARD 1 (U)
A02 AXW24T-0360 WATER LEVEL DETECTOR 1
A03 AXW1278-7FH0 DETERGENT CASE C 1 Germany
UK/Holand/Belgium/Sweden/Norway/
AXW1278-7FH0 DETERGENT CASE C 1 Denmark/Poland/Czech/Hungary/Romania/
Malaysia/Indonesia
AXW1278-7FH0 DETERGENT CASE C 1 France
AXW1278-7FH0 DETERGENT CASE C 1 Spain/Italy
AXW1278-7GY0 DETERGENT CASE C 1 UK/Holand/Belgium/Sweden/Norway/
Denmark/Poland/Czech/Hungary/Romania
AXW1278-7GY0 DETERGENT CASE C 1 France
AXW1278-7GY0 DETERGENT CASE C 1 Spain/Italy
AXW1278-7GY0 DETERGENT CASE C 1 Malaysia
AXW1278-7GY0 DETERGENT CASE C 1 Indonesia
A04 AXW2901-7FH0 FEED VALVE CASE 1 Germany
AXW2901-7FH0 FEED VALVE CASE 1 Denmark/Poland/Czech/Hungary/Romania/
Malaysia/Indonesia
AXW2901-7FH0 FEED VALVE CASE 1 France
AXW2901-7FH0 FEED VALVE CASE 1 Spain/Italy
AXW2901-7GY0 FEED VALVE CASE 1 Denmark/Poland/Czech/Hungary/Romania/
AXW2901-7GY0 FEED VALVE CASE 1 France
AXW2901-7GY0 FEED VALVE CASE 1 Spain/Italy
AXW2901-7GY0 FEED VALVE CASE 1 Malaysia
AXW2901-7GY0 FEED VALVE CASE 1 Indonesia
A05 AXW29A-22006 FEED VALVE 1
A06 AXW2164-6JU0 DETERGENT CASE PACKING 6
A07 AXW8E-7FH0 NOZZLE UNIT 1
A08 AXW2150-7FH0 DETERGENT CASE A 1
A09 AXW245-6TB0 HOSE CLAMP 2
A10 AXW1250-7FH0 FEED HOSE 1
A12 AXW2Q-7FH0 AIR HOSE A UNIT 1
A13 AXW12C-7FH0 WATER SUPPLY HOSE 1 Germany
UK/Holand/Belgium/Sweden/Norway/Denmark/
AXW12C-7FH0 WATER SUPPLY HOSE 1 Poland/Czech/Hungary/Romania/Malaysia/Indonesia
AXW12C-7FH0 WATER SUPPLY HOSE 1 France
AXW12C-7FH0 WATER SUPPLY HOSE 1 Spain/Italy
AXW12C-7GY1 WATER SUPPLY HOSE 1 UK/Holand/Belgium/Sweden/Norway/
Denmark/Poland/Czech/Hungary/Romania
AXW12C-7GY1 WATER SUPPLY HOSE 1 France
AXW12C-7GY1 WATER SUPPLY HOSE 1 Spain/Italy
AXW12C-7GY1 WATER SUPPLY HOSE 1 Malaysia
AXW12C-7GY1 WATER SUPPLY HOSE 1 Indonesia
A14 AXW229-6YK0 HOSE JOINT 1

A15 AXW229-7FH0 HOSE JOINT 2
A16 AXW264-6YK0 HOSE CLAMP 2
A17 AXW2P-7FH0 SUCTION HOSE B UNIT 1
A19 AXW264-6WJ0 HOSE CLAMP 2
A20 AXW237-7FH0 SUCTION HOSE A 1
-41-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
LOCATION OF PARTS-B
-42-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
REPLACEMENT PARTS LIST-B

Ref. Part No. Description Q'ty 168VX2 168VG2 148VA2 128VA2 147VB2 Remarks
No .
B01 AXW24S-7FH06 CONTROLLER UNIT A 1
AXW24S-7FJ06 CONTROLLER UNIT A 1
B02 AXW146-7FH2 CONTROLLER PLATE 1
AXW146-7FJ0 CONTROLLER PLATE 1
AXW146-7FK0 CONTROLLER PLATE 1
AXW146-7MM0 CONTROLLER PLATE 1
B03 AXW149A7FH0 COURSE SELECT KNOB 1
AXW149B7FH0 COURSE SELECT KNOB 1
B04 AXW1J-7MJ0 PANEL FACE BOARD UNIT 1 Germany

AXW1J-7ML0 PANEL FACE BOARD UNIT 1 Germany
AXW1J-7FK1 PANEL FACE BOARD UNIT 1 Germany
AXW1J-7MP0 PANEL FACE BOARD UNIT 1 UK/Holand/Belgium/Sweden/Norway/
Denmark/Poland/Czech/Hungary/
AXW1J-7MS0 PANEL FACE BOARD UNIT 1 Romania/Malaysia/Indonesia
AXW1J-7GZ1 PANEL FACE BOARD UNIT 1 UK/Holand/Belgium/Sweden/Norway/Denmark
AXW1J-7MW0 PANEL FACE BOARD UNIT 1 France
AXW1J-7RH0 PANEL FACE BOARD UNIT 1 France
AXW1J-7HC1 PANEL FACE BOARD UNIT 1 France
AXW1J-7MZ0 PANEL FACE BOARD UNIT 1 Spain
AXW1J-7NA0 PANEL FACE BOARD UNIT 1 Spain
AXW1J-7HF1 PANEL FACE BOARD UNIT 1 Spain
AXW1J-7ND0 PANEL FACE BOARD UNIT 1 Italy
AXW1J-7NE0 PANEL FACE BOARD UNIT 1 Italy
AXW1J-7RJ0 PANEL FACE BOARD UNIT 1 Italy
B06 AXW2177A7FH1 SOFTENER CASE CAP 1 (U)

B07 AXW21D-7MJ0 RINSE CASE UNIT 1 (U)
AXW21D-7MK0 RINSE CASE UNIT 1 (U)
AXW21D-7ML0 RINSE CASE UNIT 1 (U)
AXW21D-7MM0 RINSE CASE UNIT 1 (U)
AXW21D-7MN0 RINSE CASE UNIT 1 (U)
B08 AXW147B7MJ0 PANEL FACE C 1 (U)

AXW147B7MK0 PANEL FACE C 1 (U)
AXW147B7ML0 PANEL FACE C 1 (U)
AXW147B7MM0 PANEL FACE C 1 (U)
AXW147B7MN0 PANEL FACE C 1 (U)
B10 AXW1GH7FH0 DOOR UNIT 1 (U)
B11 AXW173G7FH0 BODY BAND PLATE 1 (U)Grey

AXW173C7FH0 BODY BAND PLATE 1 (U)Silver
AXW173B7FH0 BODY BAND PLATE 1 (U)White
B12 AXW171G7FH0 BODY BAND A 1 (U)Grey
AXW171C7FH0 BODY BAND A 1 (U)Silver
AXW171B7FH0 BODY BAND A 1 (U)White
B13 AXW11D-7FH0 DOOR HINGE 1
B14 AXW7CG7FH0 DOOR BUTTON 1 Grey
AXW7CC7FH0 DOOR BUTTON 1 Silver
AXW7CB7FH0 DOOR BUTTON 1 White
B15 AXW1619-1106 DOOR LOCK SWITCH 1
B16 AXW1BB7FH0 BODY B UNIT 1
B17 AXW163N6YK0 HOLE COVER 7 (U)Grey

AXW163M6YK0 HOLE COVER 7 (U)Silver
AXW163B6YK0 HOLE COVER 7 (U)White
B19 AXW172-6UN1 BODY BAND B 1
B20 AXW212-7EU0 WRINGER FRAME PACKING 1
B21 AXW172-6UN0 BODY BAND B 1
B22 AXW448-7KU0 CHEMIAL COVER 1
B23 AXW14A-7FH0 LEAD WIRE UNIT 1 Upper side
-43-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
LOCATION OF PARTS-C
-44-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
REPLACEMENT PARTS LIST-C

No .
C01 AXW1231-7FH1 BALANCING WEIGHT 1
C03 AXW3441-6YK1 SUSPENSION 2
C04 AXW24N-7FH0 3D SENSOR 1
C05 AXW448-20120 CHEMIAL COVER 1
C08 AXW2259-6YK1 COVER CAP 1
C09 AXW32G-7FH0 OUTER TUB COVER 1 Includes C12

C10 AXW12A-7FH1 OUTER TUB COMPLETE 1 Includes C21.C37
C12 AXW822-6UN0 OUTER TUB PACKING 1 Included in C09
C13 AXW2258-6YK0 COVER 1
C14 AXW2228A7FH0 BAFFLE PLATE 3 Included in C15
C15 AXW22B-7MJ0 DRUM A UNIT 1 Includes C14

AXW22B-7FH0 DRUM A UNIT 1 Includes C14
C16 AXW24N-040 THERMAL DETECTOR UNIT 1
C17 AXW1371-6UN1 THERMAL DETECTOR HOLDER 1
C18 AXW307-7EU0 MOTOR PLATE A 1
C19 AXW3482-3106 GEARED MOTOR 1
C20 AXW903-6UN0 VALVE PACKING UNIT 1

C21 AXW9D-7MJ0 VALVE FRAME UNIT 1 Included in C10
C22 AXW245-6WJ1 HOSE CLAMP 1
C23 AXW231-7FH0 DRAIN HOSE B 1
C24 AXW245-6WJ0 HOSE CLAMP 1
C25 AXW420-6UN6 MOTOR WASHER A 4

C26 AXW477-6YK1 MOTOR COVER B 1
C27 AXW401-7FH06 MOTOR 1
C28 AXW448-6UN0 CHEMIAL COVER 1
C29 AXW420-6UN5 MOTOR WASHER A 2
C30 AXW333-7FH0 EARTH WIRE PLATE 1

C31 AXW5F-7FH0 IMPELLER PULLEY 1
C32 AXW1238-7BB0 WATER PROTECTION COVER 1
C33 AXW13C-75105 HEATER UNIT 1
C34 AXW412-7FH0 BELT 1 (U)
C35 AXW479-6YK1 MOTOR COVER C 1

C36 AXW448-20120 CHEMIAL COVER 1
C37 AXW822-6UN2 OUTER TUB PACKING 1 Included in C10
C38 AXW518-6UN00 WASHER 2
C39 AXW232-7MJ0 DRAIN HOSE C 1
C40 AXW264-7FH0 HOSE CLAMP 2
-45-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
LOCATION OF PARTS-D
Accessories
-46-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
REPLACEMENT PARTS LIST-D

No .
D01 AXW1150-7FH0 TUB SUPPORT PLATE 1
D02 AXW2331-7MJ0 DAMPER SPRING 2
AXW2331-6YK2 DAMPER SPRING 2
D03 AXW1AB7FH0 BODY UNIT 1 Includes D05
D04 AXW135-7FH0 HOOK 4
D05 AXW3I-7EU0 LEG PLATE UNIT 4 (U)
D07 AXW2205A7FH0 DRAIN FILTER 1 (U) Includes Seal ring

D08 AXW334-6YK0 DAMPER HOLDER PIN 2
D09 AXW260-6WJ0 SUB DRAIN PORT CAP 1 (U)
D10 AXW264-6WJ0 HOSE CLAMP 2 (U)
D11 AXW230-7FH0 DRAIN HOSE A 1
D12 AXW1150-7FH1 TUB SUPPORT PLATE 1
D13 AXW8R-7FH0 DRAINING PUMP UNIT 1 Includes D07

D14 AXW686-7EP0 WATERPROOF COVER 1
D15 AXW26M-7FH0 FILTER VALVE LEAD SWITCH 1
D16 AXW245-6WJ4 HOSE CLAMP 1
D17 AXW2EA7FH0 DRAINING HOSE UNIT 1
D18 AXW120A7FH0 DRAIN HOSE HOLDER 3 (U)Inside

D19 AXW170A7FH0 DRAIN HOSE HOLDER 1
D20 SFT-72SN MAGNET RING 1
D21 AXW4A-7FH0 POWER CORD 1 Germany/France/Spain/Holand/
Belgium/Sweden/ Norway/Denmark/
Poland/Czech/Hungary/Romania
AXW4A-7GX0 POWER CORD 1 UK
AXW4A-7LA0 POWER CORD 1 Italy
AXW4A-7KL0 POWER CORD 1 Malaysia/Indonesia
D22 AXW156-7FH0 REAR PANEL 1 (U)
D23 AXW90E-7FH1 OUTER TUB HOLDER UNIT 4 (U)

D24 AXW120A7FH1 DRAIN HOSE HOLDER 3 (U)Outside
D25 AXW24C-7MJ06 PC BOARD W/COMPONENTS 1
AXW24C-7MK06 PC BOARD W/COMPONENTS 1 Germany/France
UK/Holand/Belgium/Sweden/
AXW24C-7MR06 PC BOARD W/COMPONENTS 1 Norway/Denmark/Poland/Czech/
Hungary/Romania
AXW24C-7ML06 PC BOARD W/COMPONENTS 1 Germany
UK/France/Spain/Italy/Holand/
AXW24C-7MS06 PC BOARD W/COMPONENTS 1 Belgium/Sweden/Norway/Denmark/
Poland/Czech/Hungary/Romania/Malaysia
AXW24C-7MM06 PC BOARD W/COMPONENTS 1 Germany
UK/France/Spain/Italy/Holand/Belgium/
AXW24C-7MT06 PC BOARD W/COMPONENTS 1 Sweden/Norway/Denmark/Poland/Czech/
Hungary/Romania/Malaysia/Indonesia
AXW24C-7FK06 PC BOARD W/COMPONENTS 1 Germany
UK/France/Spain/Italy/Holand/
AXW24C-7GZ06 PC BOARD W/COMPONENTS 1 Belgium/Sweden/Norway/Denmark/
Poland/Czech/Hungary/Romania
D26 AXW2430-0400 NOISE FILTER 1

D27 AXW542-7FH0 PC BOARD COVER C 1
D28 L6FAKEDH0014 FAN UNIT 1
D29 AXW14B-7FH0 LEAD WIRE UNIT B 1 Lower side
D30 AXW621-7FH0 SWITCH PLATE A 1
D31 AXW624-7FH0 SWITCH PLATE B 1

D32 AXW14A-7FH1 WATER LEAK SENSOR 1
D33 AXW2159-7FH0 BOTTOM PLATE A 1 Includes Seal ring
D34 AXW130B7FH0 PANEL A 1 Includes Label
D35 AXW140B7FH0 PANEL B 1 (U)
D36 AXW3440-7FH0 SUSPENSION HOLDER 2

D37 AXW1188-6YK0 COVER CAPS 4 (U)
D38 AXW526-7FH0 SPANNER 1 (U)
D39 AXW229-6WJ0 DRAIN HOSE JOINT A 1 (U)
D40 AXW4595-7FH0 METAL COVER(NOT PAINTED) 1 (U)
AXW4595-7KG0 METAL COVER(WHITE) 1 (U)
-47-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
PACKING INSTRUCTIONS
PACKING PARTS LIST

No .
Germany/UK/Spain/Italy/Holand/Belgium/
1 AXW9001-7MJ1 CASE A 1 Sweden/Norway/Denmark/Poland/Czech/
Hungary/Romania/Malaysia
Germany/UK/France/Holand/Belgium/Sweden/
AXW9001-7MK1 CASE A 1
Norway/Denmark/Poland/Czech/Hungary/Romania
Germany/UK/France/Spain/Italy/Holand/Belgium/Sweden
AXW9001-7ML1 CASE A 1 /Norway/Denmark/Poland/Czech/Hungary/Romania/Malaysia
Germany/UK/France/Spain/Italy/Holand/Belgium/Sweden
AXW9001-7MM1 CASE A 1 /Norway/Denmark/Poland/Czech/Hungary/Romania/Malaysia
Germany/UK/France/Spain/Italy/Holand/Belgium/Sweden/
AXW9001-7MN1 CASE A 1 Norway/Denmark/Poland/Czech/Hungary/Romania
AXW9001-7TJ0 CASE A 1 Indonesia
AXW9001-7TH0 CASE A 1 Indonesia
2 AXW9923-7FH1 GUARANTEE SERVICE BOOK 1
AXW9923-7RV1 GUARANTEE SERVICE BOOK 1 Malaysia
AXW9923-7RW1 GUARANTEE SERVICE BOOK 1 Malaysia
AXW9923-7RX1 GUARANTEE SERVICE BOOK 1 Malaysia
AXW9923-7TJ0 GUARANTEE SERVICE BOOK 1 Indonesia
AXW9923-7TH0 GUARANTEE SERVICE BOOK 1 Indonesia
3 AXW90B-7FH0 CASE B 1
4 AXW9004-7FH0 BODY COVER(L) 1
5 AXW9004-7FH1 BODY COVER(R) 1
6 AXW9069-7FH0 UPPER SHEET 1
7 AXW9057-7FH3 ACCESSORY PACK 1 Operating instructions

8 AXW9057-7FH1 ACCESSORY PACK 3 Power cord
9 AXW4F-7MJ0 OPERATING INSTRUCTIONS 1 Germany
AXW4F-7MP0 OPERATING INSTRUCTIONS 1 UK
AXW4F-7MW0 OPERATING INSTRUCTIONS 1 - France
AXW4F-7MZ0 OPERATING INSTRUCTIONS 1 - Spain
AXW4F-7ND0 OPERATING INSTRUCTIONS 1 - Italy
Holand/Belgium/Sweden/Norway/Danmark/
AXW4F-7NG0 OPERATING INSTRUCTIONS 1 Poland/Czech/Hungary/Romania
AXW4F-7TJ0 OPERATING INSTRUCTIONS 1 - - - Indonesia
AXW4F-7RV0 OPERATING INSTRUCTIONS 1 - - Malaysia
10 AXW9060-7FH0 UPPER COVER 1
11 AXW9070-7BB0 DOOR SHEET 1
12 AXW9054-7FH1 DRUM SUPPORTER 1
AXW9054-7FH2 DRUM SUPPORTER 1
-48-

NA-168VX2/168VG2/148VA2/128VA2/147VB2
SMALL STANDARDIZED METAL PARTS

No .
1 XTWAXW466J SCREW 10
2 XTB4+16CFJ SCREW 20
3 XTB4+10FFJ SCREW 35
4 XTB4+16CXR SCREW 1
5 XTBAXW437J SCREW 19
6 XTBAXW438J SCREW 2
7 XST4+16V SCREW 3
8 XTT4+12FXR SCREW 7
9 XWL10J27FJ WASHER 6
11 XWL7J27FJ WASHER 5
12 XTWAXW6520 SCREW 3
14 XTTAXW511 SCREW 1
15 XVGAXW848 SCREW 6
16 XTB4+12CV SCREW 10
17 XTB4+12BFJ SCREW 7
21 XTT4+16BX SCREW 2
22 XYA5+12CHFJ SCREW 1
23 XNGAXW1801J NUT 1
24 XTB4+12GFJ SCREW 3
25 XWAAXW601 SCREW 1
26 XNF6FJ NUT 1
28 XVHAXW1008J SCREW 2
30 XTWAXW473 SCREW 3
32 XYN5+C10BN SCREW 1
-49-

Na168vx2 Service Manual

Uploaded by

Copyright:

Available Formats

Na168vx2 Service Manual

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Na168vx2 Service Manual

Uploaded by

Copyright:

Available Formats

Order No.

Drum Type Washing Machine

IMPORTANT SAFETY NOTICE

C Panasonic HA Washing Machine Hangzhou 2010.

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Horizontal drum type Tilted drum

2-2 Produce high washability

Shower from the upper portion

Downloaded from www.Manualslib.com manuals search engine

2-3-1 Optional Washing Settings

Conducts a more Adds an extra Add a pre-wash Prevent wrinkles caused by

For 168VG2, 148VA2/147VB2, 128VA2(LED Display)

Downloaded from www.Manualslib.com manuals search engine

2-4 How to turn the "end of programme" buzzer on or off

1 Press the START and power ON buttons at the same

2-5 Wide angle water supply shower

Rinsing Water Supply Shower

Downloaded from www.Manualslib.com manuals search engine

2-6 Smart Beat Wash by variable rotation control

45 r/min 45 r/min 45 r/min

New washing method (Variable rotation control)

If clothes shall not be

Increased rotation Decreased rotation Decreased rotation

How to check the 3D sensor

Operate approx. 2 minutes with no load

Incase there is no data and signal coming from the

Downloaded from www.Manualslib.com manuals search engine

Water Supply Valve

Premium Deluxe Standard

2-8 Switching Sensor Panasonic

Downloaded from www.Manualslib.com manuals search engine

2-9 How to lock or unlock the door

To unlock the door while a programme is running

2-10 How to set and reset the child safety lock

1 Switch the washing machine on.

2-11 Release the door lock for servicing

Push the small hole between the door

Downloaded from www.Manualslib.com manuals search engine

3 KNOW THE WASHING MACHINE

(Push the door opening

Do not fold the

Downloaded from www.Manualslib.com manuals search engine

4 MOVING AND INSTALLING

4-2 Removing the anchor bolts

To remove the anchor bolts:

4-3 Moving the washing machine from one location to another

4-4 Attaching the anchor bolts

Downloaded from www.Manualslib.com manuals search engine

4-5 The right place for washing machine

Sloping Unstable Bumpy

Other things to avoid:

4-6 Washing machine dimensions in millimetres

4-7 Installing a built-in washing machine

Metal cover Separately sold accessories

Downloaded from www.Manualslib.com manuals search engine

How to adjust frequency of the water level detector

Part No. : AXW4595-7FH0