Global Roofing Solutions

Bond-Dek™
Composite Deck

Talk to us, THE SMART DECKING PEOPLE

Visit www.globalroofs.co.za or email
[email protected]
 Bond-Dek™ composite deck

• Bond-Dek™ is a composite steel flooring

system for multi-storey steel or concrete
buildings.
• Bond-Dek™'s unique side-lap interlocking
system provides for fast and simple
construction. The speed of erection results
in major labour cost savings.
• Bond-Dek™ is able to span up to 3 metres
unsupported under wet concrete with a
minimum depth of 65mm over the profile.
• Bond-Dek™ will accept most floor service
systems.
• Bond-Dek™ is avilable in a galvanised
coated steel and stainless steel 0,8mm,
1,0mm and 1,2mm thick.
• Bond-Dek™ has been fire tested by the
CSIR and has qualified for a rating of 120
minutes.
• Brownbuilt has been assessed and certified
complying with ISO 9002 Quality
Management Systems.

The Bond-Dek™ profile displaces

0,037 m3 per m2 of deck.

Refer to the Bond-Dek™ Installation

procedure before proceeding with
installation of panels (pages 6-11).
General
1. Bond-Dek™ floor slabs are basically one-way slabs cover along supports (typically on top of shear studs).
designed to carry uniformly distributed loads. The tables do This gives the following ratings for a nominal superimposed
not cater for heavy concentrated loads or moving loads. load of 2,5 kN/m2 maximum, for spans up to 3,0 m.
Where these occur the design should be referred to a civil / 120 minutes - where the thickness of the slab plus any
structural engineer. concrete screed is greater than 170 mm, and 90 minutes -
2. Calculations are generally in accordance with where the thickness of the slab plus any concrete screed is
BS5950 : Part 4 : 1984 (limit states design). Deflection less than 170 mm.
during construction calculated at span/180m.
3. Where the Bond-Dek™ is not fixed directly to the end For further information on fire applications contact GRS.
supports (e.g. shear studs, hilti nails, etc.) steel closer N.B. All tabulated values serve as a guide only for single span
pieces or transverse straps are required along the ends. conditions, and should be certified and approved by a
4. For normal applications of Bond-Dek™ steel floors, no civil/structural engineer.
additional reinforcing other than a light mesh for shrinkage
Accessories
control is required, typically 193 mesh.
The following accessories are avilable for use with Bond-Dek™:
5. For “Fire Applications” of Bond-Dek™ floors, welded steel
Steel side and end closers, self-tapping screws, pop rivets,
mesh reinforcement of 8 mm diameter steel bars at 200
hammer drive screws and flashings made to order.
mm spacing in each direction is required, with minimum top

SECTION PROPERTIES OF STEEL DECKING – SIMPLY SUPPORTED CONDITION

Thickness (mm) Area of steel per Minimum reduced Reduced “I” per Effective depth of Neutral axis from
Mass per square
meter width of cross “Z” per meter width meter width Bond-Dek™ bottom of
Nominal Effective meter (kg/m2)
section (mm2) (103mm3) (105mm4) (mm) Bond-Dek™ (mm)
0,8 0,76 993 7,8 22,2 0,884 74,76 35,05

1,0 0,96 1254 9,85 30,3 1,170 74,96 36,38

1,2 1,16 1515 11,9 38,7 1,463 75,16 37,37

Bond-Dek™ composite deck allowable tables

0,8mm THICK COMPOSITE BOND-DEK™ SLAB
Nominal Nominal uniformly distributed superimposed load (Ln) in kN/m2
Depth dead load for simply supported conditions
of slab of slab 25 Mpa concrete
(mm) (Dn)
(kN/m2) Span in metres

2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50
140 2,52 10,00 8,72 7,80 6,84 6,10 5,37 4,80
150 2,75 10,00 9,61 8,60 7,53 6,70 5,93 5,30
160 2,99 10,00 10,00 9,39 8,21 7,29 6,46 5,79
170 3,22 10,00 10,00 10,00 8,79 7,89 7,01 6,29
180 3,46 10,00 10,00 10,00 9,43 8,48 7,54 6,78 6,13
190 3,69 10,00 10,00 10,00 10,00 9,17 8,11 7,27 6,50 5,87
200 3,93 10,00 10,00 10,00 10,00 10,00 8,49 7,76 6,94 6,26 5,66 5,16
210 4,17 10,00 10,00 10,00 10,00 10,00 9,03 8,24 7,36 6,64 5,99 5,44
220 4,40 10,00 10,00 10,00 10,00 10,00 9,58 8,74 7,86 7,14 6,42 5,84
230 4,64 10,00 10,00 10,00 10,00 10,00 10,00 9,23 8,28 7,553 6,75 6,13
240 4,87 10,00 10,00 10,00 10,00 10,00 10,00 10,00 8,74 7,93 7,11 6,42
250 5,11 10,00 10,00 10,00 10,00 10,00 10,00 10,00 9,14 8,32 7,51 6,82

*Broken line indicates maximum modified span/20.

Spans to the right of the solid line require propping during construction.

0,8mm THICK BOND-DEK™ DECKING SPANS DURING CONSTRUCTION (UNPROPPED)

Allowing for a construction load of 1,5 kN/m2 plus wet concrete
Slab depth (mm) 140 150 160 170 180 190 200 210 220 230 240 250
Unpropped span (m) 2,7 2,6 2,6 2,5 2,4 2,4 2,3 2,3 2,2 2,2 2,1 2,1
 1,0mm THICK COMPOSITE BOND-DEK™ SLAB
Nominal Nominal uniformly distributed superimposed load (Ln) in kN/m2
Depth dead load for simply supported conditions
of slab of slab 25 Mpa concrete
(mm) (Dn)
(kN/m2) Span in metres

2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50
140 2,53 10,00 8,73 7,81 6,84 6,11 5,38 4,81
150 2,77 10,00 9,61 8,60 7,53 6,70 5,93 5,30
160 3,00 10,00 10,00 9,40 8,21 7,30 6,46 5,80
170 3,24 10,00 10,00 10,00 8,79 7,89 7,01 6,29
180 3,48 10,00 10,00 10,00 9,43 8,48 7,54 6,78
190 3,71 10,00 10,00 10,00 10,00 9,07 8,06 7,27 6,49 5,86
200 3,95 10,00 10,00 10,00 10,00 10,00 8,49 7,76 6,94 6,26 5,66 5,16
210 4,19 10,00 10,00 10,00 10,00 10,00 9,03 8,24 7,36 6,64 5,99 5,44
220 4,42 10,00 10,00 10,00 10,00 10,00 9,59 8,74 7,81 7,04 6,33 5,74
230 4,66 10,00 10,00 10,00 10,00 10,00 10,00 9,23 8,24 7,42 6,72 6,13
240 4,89 10,00 10,00 10,00 10,00 10,00 10,00 10,00 8,59 7,83 7,07 6,43
250 5,13 10,00 10,00 10,00 10,00 10,00 10,00 10,00 8,98 8,22 7,46 6,82

*Broken line indicates maximum modified span/20.

Spans to the right of the solid line require propping during construction.

1,0mm THICK BOND-DEK™ DECKING SPANS DURING CONSTRUCTION (UNPROPPED)

Allowing for a construction load of 1,5 kN/m2 plus wet concrete
Slab depth (mm) 140 150 160 170 180 190 200 210 220 230 240 250
Unpropped span (m) 3,2 3,1 3,0 2,9 2,8 2,8 2,7 2,7 2,6 2,6 2,5 2,5

1,2mm THICK COMPOSITE BOND-DEK™ SLAB

Nominal Nominal uniformly distributed superimposed load (Ln) in kN/m2
Depth dead load for simply supported conditions
of slab of slab 25 Mpa concrete
(mm) (Dn)
(kN/m2) Span in metres

2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50
140 2,56 10,00 8,75 7,80 6,80 6,00 5,34 4,80
150 2,79 10,00 9,46 8,50 7,45 6,60 5,89 5,30
160 3,03 10,00 10,00 9,29 8,16 7,29 6,45 5,79
170 3,27 10,00 10,00 10,00 8,78 7,88 7,00 6,28
180 3,50 10,00 10,00 10,00 9,48 8,48 7,54 6,78
190 3,74 10,00 10,00 10,00 10,00 9,06 8,06 7,26 6,49 5,87
200 3,97 10,00 10,00 10,00 10,00 10,00 8,76 7,76 6,94 6,26 5,66 5,16
210 4,21 10,00 10,00 10,00 10,00 10,00 9,33 8,24 7,36 6,64 5,99 5,44
220 4,44 10,00 10,00 10,00 10,00 10,00 9,69 8,74 7,81 7,04 6,33 5,74
230 4,68 10,00 10,00 10,00 10,00 10,00 10,00 9,13 8,19 7,43 6,72 6,13
240 4,91 10,00 10,00 10,00 10,00 10,00 10,00 10,00 8,63 7,83 7,07 6,42
250 5,15 10,00 10,00 10,00 10,00 10,00 10,00 10,00 9,09 8,22 7,41 6,72

*Broken line indicates maximum modified span/20.

Spans to the right of the solid line require propping during construction.

1,2mm THICK BOND-DEK™ DECKING SPANS DURING CONSTRUCTION (UNPROPPED)

Allowing for a construction load of 1,5 kN/m2 plus wet concrete
Slab depth (mm) 140 150 160 170 180 190 200 210 220 230 240 250
Unpropped span (m) 3,5 3,4 3,4 3,3 3,2 3,1 3,1 3,0 2,9 2,9 2,8 2,8
 Bond-Dek™ composite deck factored tables

0,8mm THICK COMPOSITE BOND-DEK™ SLAB

Nominal Total FACTORED uniformly distributed superimposed load in kN/m2
Depth dead load for simply supported conditions (1,4 Dn + 1,6 Ln)
of slab of slab 25 Mpa concrete
(mm) (Dn)
(kN/m2) Span in metres

2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50
140 2,52 19,53 17,48 16,01 14,47 13,29 12,13 11,21
150 2,75 19,85 19,22 17,62 15,90 14,85 13,33 12,34
160 2,99 20,19 20,19 19,20 17,32 15,84 14,52 13,44
170 3,22 20,51 20,51 20,51 18,57 17,13 15,72 14,57
180 3,46 20,84 20,84 20,84 19,93 18,41 16,91 15,69 14,64
190 3,69 21,17 21,17 21,17 21,17 19,84 18,15 16,80 15,57 14,56
200 3,93 21,50 21,50 21,50 21,50 21,50 19,08 17,32 16,61 15,52 14,56 13,76
210 4,17 21,84 21,84 21,84 21,84 21,84 20,29 19,03 17,62 16,47 15,42 14,55
220 4,40 22,16 22,16 22,16 22,16 22,16 21,48 20,15 18,73 17,59 16,44 15,51
230 4,64 22,50 22,50 22,50 22,50 22,50 22,50 21,26 19,74 18,54 17,30 16,30
240 4,87 22,82 22,82 22,82 22,82 22,82 22,82 22,82 20,81 19,50 18,20 17,10
250 5,11 23,15 23,15 23,15 23,15 23,15 23,15 23,15 21,77 20,46 19,16 18,06

*Broken line indicates maximum modified span/20.

Spans to the right of the solid line require propping during construction.

0,8mm THICK BOND-DEK™ DECKING SPANS DURING CONSTRUCTION (UNPROPPED)

Allowing for a construction load of 1,5 kN/m2 plus wet concrete
Slab depth (mm) 140 150 160 170 180 190 200 210 220 230 240 250
Unpropped span (m) 2,7 2,6 2,6 2,5 2,4 2,4 2,3 2,3 2,2 2,2 2,1 2,1

1,0mm THICK COMPOSITE BOND-DEK™ SLAB

Nominal Nominal uniformly distributed superimposed load (Ln) in kN/m2
Depth dead load for simply supported conditions
of slab of slab 25 Mpa concrete
(mm) (Dn)
(kN/m2) Span in metres

2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50
140 2,53 19,54 17,50 16,04 14,49 13,32 12,15 11,24
150 2,77 19,88 19,25 17,64 15,93 14,60 13,36 12,36
160 3,00 20,20 20,20 19,23 17,34 15,87 14,54 13,47
170 3,24 20,54 20,54 20,54 18,60 17,15 15,75 14,59
180 3,48 20,87 20,87 20,87 19,96 18,44 16,94 15,72 14,67
190 3,71 21,19 21,19 21,19 21,19 19,70 18,09 16,82 15,59 14,58
200 3,95 21,53 21,53 21,53 21,53 21,53 19,12 17,95 16,64 15,55 14,59 13,79
210 4,19 21,87 21,87 21,87 21,87 21,87 20,32 19,05 17,65 16,49 15,45 14,57
220 4,42 22,19 22,19 22,19 22,19 22,19 21,54 20,18 18,68 17,46 16,32 15,38
230 4,66 22,52 22,52 22,52 22,52 22,52 22,52 21,28 19,71 18,40 17,27 16,32
240 4,89 22,85 22,85 22,85 22,85 22,85 22,85 22,85 20,59 19,37 18,16 17,13
250 5,13 23,18 23,18 23,18 23,18 23,18 23,18 23,18 21,55 20,33 19,12 18,09

*Broken line indicates maximum modified span/20.

Spans to the right of the solid line require propping during construction.

1,0mm THICK BOND-DEK™ DECKING SPANS DURING CONSTRUCTION (UNPROPPED)

Allowing for a construction load of 1,5 kN/m2 plus wet concrete
Slab depth (mm) 140 150 160 170 180 190 200 210 220 230 240 250
Unpropped span (m) 3,2 3,1 3,0 2,9 2,8 2,8 2,7 2,7 2,6 2,6 2,5 2,5
 1,2mm THICK COMPOSITE BOND-DEK™ SLAB
Nominal Nominal uniformly distributed superimposed load (Ln) in kN/m2
Depth dead load for simply supported conditions
of slab of slab 25 Mpa concrete
(mm) (Dn)
(kN/m2) Span in metres

2,00 2,25 2,50 2,75 3,00 3,25 3,50 3,75 4,00 4,25 4,50
140 2,56 19,58 17,58 16,07 14,46 13,19 12,13 11,27
150 2,79 19,91 19,04 17,51 15,83 14,47 13,34 12,39
160 3,03 20,24 20,24 19,10 17,29 15,90 14,56 13,50
170 3,27 20,58 20,58 20,58 18,62 17,18 15,78 14,64
180 3,50 20,90 20,90 20,90 20,06 18,46 16,97 15,74 14,69
190 3,74 21,24 21,24 21,24 21,24 19,73 18,13 16,87 15,64 14,62
200 3,97 21,56 21,56 21,56 21,56 21,56 19,57 17,97 16,67 15,57 14,62 13,81
210 4,21 21,89 21,89 21,89 21,89 21,89 20,81 19,08 17,67 16,52 15,47 14,60
220 4,44 22,22 22,22 22,22 22,22 22,22 21,72 20,20 18,71 17,48 16,35 15,40
230 4,68 22,55 22,55 22,55 22,55 22,55 22,55 21,15 19,66 18,43 17,30 16,35
240 4,91 22,87 22,87 22,87 22,87 22,87 22,87 22,87 20,68 19,39 18,18 17,15
250 5,15 23,21 23,21 23,21 23,21 23,21 23,21 23,21 21,75 20,36 19,06 17,96

*Broken line indicates maximum modified span/20.

Spans to the right of the solid line require propping during construction.

1,2mm THICK BOND-DEK™ DECKING SPANS DURING CONSTRUCTION (UNPROPPED)

Allowing for a construction load of 1,5 kN/m2 plus wet concrete
Slab depth (mm) 140 150 160 170 180 190 200 210 220 230 240 250
Unpropped span (m) 3,5 3,4 3,4 3,3 3,2 3,1 3,1 3,0 2,9 2,9 2,8 2,8

Installation procedure
(read entire procedure before pouring concrete)
Bond-Dek™ panels act as framework for wet
concrete and reinforcing for the slab. To
commence installation the first Bond-Dek™
panel is placed in the required position with
the male interlocking rib pointing in the
direction of laying as per sketch below. Place
the female interlocking rib to the outside.
Place the interlocking female rib of the
second panel onto the male rib of the first
panel at an approximate 45° angle and then
lower panel down onto supports locking the
side lap together (see sketch, right). Repeat
for each additional panel.
 End lapping of sheets
The standard procedure is to lap Bond-Dek™
and not to butt joint it. To end lap Bond-Dek™
panels cut back 25mm on male and female
interlocking ribs on the bottom panel then
overlap top panel. Fix with Top Speed screws
into beam to ensure lateral stability at
supports.

Structural steelwork
Bond-Dek™ panels can be conveniently fixed
to steel supports with either “Top Speed”
screws or shot driven fasteners. One fixing in
each pan is required.

Shear stud
If shear studs are to be used these should
be placed in the pan of the panel over a
beam. Where panels are end lapped, this lap
of 25 mm must be to one side of the beam,
allowing for shear stud to be positioned
through the centre of the beam and fixed
through the bottom panel (see sketch below).
 Preventing concrete run out at Bond-Dek ends

When utilising a closer at the ends of the

Bond-Dek™ panels (see sketch alongside),
this provides lateral stability without the use
of strapping (closer to fit snugly over Bond-
Dek™).

Concrete or brick construction

Before laying any Bond-Dek™ panels ensure
that the top face of the concrete beam or the
brick wall is level. An uneven top face will
result in an excessive amount of concrete in
places and therefore possible overloading.
Installation of the Bond-Dek™ is to simply
place the panels onto the concrete beams or
the top of the brick walls. A steel strap is
placed across the panels and fixed at each
flute (see sketch below). This is done to
ensure lateral stability while casting the slab.
When the deck is spanning its maximum, a
steel strap should be fixed at mid span as
well as the ends.

Fixing to concrete
 Side fixing to supporting structure

Bend down cut edge of panel and fix with

Top Speed or shot driven fastener. Ensure
angle* of rib remains the same. Alternatively
a make-up Z-piece 75 mm deep can be fixed
to the beam and Bond-Dek™.

Fixing around columns

 Kerb flashing

Standard kerb flashing is secured by riveting

the bottom of the deck to the bottom of the
Kerb flash, and the top by riveting a steel
strap to the top leg of the Kerb flash and the
top of the Bond-Dek™ rib. Kerb flashings to
be a minimum of 1 mm thick.

For “Fire Applications” of Bond-Dek™ floors, welded steel mesh reinforcement of 8 mm diameter steel bars at 200 mm centres in
each direction is required with minimum top cover along supports (typically on top of shear studs).
 Pouring concrete

Standard kerb flashing is secured by riveting

the bottom of the deck to the bottom of the
Kerb flash, and the top by riveting a steel
strap to the top leg of the Kerb flash and the
top of the Bond-Dek™ rib. Kerb flashings to
be a minimum of 1 mm thick.

Safe load tables

0,8 THICK BOND-DEK™ DECKING SPANS DURING CONSTRUCTION (UNPROPPED)
Allowing for a construction load of 1,5 kN/m2 plus wet concrete
Slab depth (mm) 140 150 160 170 180 190 200 210 220 230 240 250
Unpropped span (m) 2,7 2,6 2,6 2,5 2,4 2,4 2,3 2,3 2,2 2,2 2,1 2,1

1,0 THICK BOND-DEK™ DECKING SPANS DURING CONSTRUCTION (UNPROPPED)

Allowing for a construction load of 1,5 kN/m2 plus wet concrete
Slab depth (mm) 140 150 160 170 180 190 200 210 220 230 240 250
Unpropped span (m) 3,2 3,1 3,0 2,9 2,8 2,8 2,7 2,7 2,6 2,6 2,5 2,5

1,2 THICK BOND-DEK™ DECKING SPANS DURING CONSTRUCTION (UNPROPPED)

Allowing for a construction load of 1,5 kN/m2 plus wet concrete
Slab depth (mm) 140 150 160 170 180 190 200 210 220 230 240 250
Unpropped span (m) 3,5 3,4 3,4 3,3 3,2 3,1 3,1 3,0 2,9 2,9 2,8 2,8
GRS Bond-Dek 08/15

Boksburg Tel: (011) 898 2900 Fax: (011) 892 1455 Zambia Tel: +260967495541
Cape Town Tel: (021) 521 1900 Fax: (021) 556 6936 Botswana Tel: +267 3105761 Fax: +267 3105762
Durban Tel: (031) 538 0940/1/2 Fax: (031) 502 3764 Namibia Tel: +264(0)61 263890 Fax: +264(0)61 263890
East London Tel: (043) 731 1895/98 Fax: (043) 731 1926 Zimbabwe Tel: +263 4 774 699
Bloemfontein Tel: (051) 432 3724/6 Fax: (051) 432 3723 GRS Exports Tel: (011) 898 2900 Fax: (011) 892 1455
Rustenburg Tel: (014) 596 6121 Fax: 086 644 8344 Helm Engineering Tel: (011) 876 1300 Fax: (011) 876 1304

www.globalroofs.co.za
[email protected]