Scribd
Upload
113 views1 page

Drying and Curing Time: Technical Data Sheet Jotaprime 500

Jotaprime 500 is a surface tolerant, water-based epoxy coating suitable for application by airless spray. It requires thinning with Jotun Thinner No. 17 and an airless spray nozzle tip between 17-23 with a minimum pressure of 150 bar/2100 psi. Jotaprime 500 is touch dry in 2 hours at 23°C and overcoat ready in 4 hours at the same temperature, with full service after 7 days. It has a pot life of 1 hour and can withstand continuous dry heat up to 120°C and intermittent sea water immersion up to 50°C.

Uploaded by

TamerTamer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
113 views1 page

Drying and Curing Time: Technical Data Sheet Jotaprime 500

Jotaprime 500 is a surface tolerant, water-based epoxy coating suitable for application by airless spray. It requires thinning with Jotun Thinner No. 17 and an airless spray nozzle tip between 17-23 with a minimum pressure of 150 bar/2100 psi. Jotaprime 500 is touch dry in 2 hours at 23°C and overcoat ready in 4 hours at the same temperature, with full service after 7 days. It has a pot life of 1 hour and can withstand continuous dry heat up to 120°C and intermittent sea water immersion up to 50°C.

Uploaded by

TamerTamer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Technical Data Sheet

Jotaprime 500

Thinner/Cleaning solvent
Thinner: Jotun Thinner No. 17

Guiding data for airless spray


Nozzle tip (inch/1000): 17-23
Pressure at nozzle (minimum): 150 bar/2100 psi

Drying and Curing time


Substrate temperature -5 °C 0 °C 5 °C 10 °C 23 °C 40 °C

Surface (touch) dry 20 h 14 h 6h 4h 2 h 1 h


Walk-on-dry 48 h 30 h 16 h 10 h 4 h 2 h
Dry to over coat, minimum 48 h 30 h 16 h 10 h 4 h 2 h
Dried/cured for service 30 d 21 d 14 d 10 d 7 d 3 d

For maximum overcoating intervals, refer to the Application Guide (AG) for this product.

Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and
at average of the DFT range for the product.

Surface (touch) dry: The state of drying when slight pressure with a finger does not leave an imprint or reveal
tackiness.

Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
imprints or other physical damage.

Dry to over coat, minimum: The recommended shortest time before the next coat can be applied.

Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended
environment/medium.

Induction time and Pot life


Paint temperature 23 °C

Pot life 1h

Heat resistance
Temperature
Continuous Peak

Dry, atmospheric 120 °C 140 °C


Immersed, sea water 50 °C 60 °C

Peak temperature duration max. 1 hour.

Date of issue: 28 January 2019 Page: 3/5

This Technical Data Sheet supersedes those previously issued.


The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the
Application Guide (AG) for this product. For your nearest local Jotun office, please visit our website at www.jotun.com

You might also like