WRITTEN TEST

I. True or False
Direction: Tell whether the following statement is True or False. Write (T) if
it is True and (F) if it is False in the space provided.
_________1. Work instructions provides a detailed breakdown of instructions
required to carry out one or more steps or tasks in a procedure.
_________2. Terminal lugs are recommended for use with solid wire.
_________3. Philips Screw driver has a straight or flat tip.
_________4.Poor lighting and ventilation are examples of physical hazards.
_________5. OSH means Occupational Security and Health.
_________6. To control hazards and risks, it is necessary to conduct a hazard
assessment.
_________7. In a single phase induction motor, the resistance of the running
winding (RW) is higher than the starting winding (SW).
_________8. Wye-Delta reduced voltage starters are applicable only with
motors all nine motor leads available.
_________9. Before you test installed mechatronics devices, a report of
testing must be done.
_________10. Before you test installed mechatronics devices, a report of
testing must be done. Resistance checking of installed
mechatronics devices must be done before applying power.

II. Multiple Choice

Direction: Encircle the letter of the correct answer.
1. Purpose is the part of work instructions which informs the worker
about _______________.
A. area or process that instruction applies
B. reason for writing work instruction
C. equipment to be secured
D. instructions to be follow

2. What are the benefits of using work instructions?

I. Instructions are conveyed in very detailed manner
II. Process is standardised
III. Waste are reduced
IV. Training is simplified and consistent

A. I and IV only
B. I and II only
C. I, II and IV
D. I, II, III and IV
3. A megger is used to measure _______________.
A. reactance
B. current
C. specific gravity
D. insulation resistance

4. Wire stripper is used for _______________.

A. cutting wires
B. crimping terminals on wires
C. removing the insulation of wires
D. reaming small diameter conduits

5. Which of the following material will you use to connect terminal of a

device to another device?
A. Wire
B. Tubing
C. Terminal Screw
D. Electrical Tape

6. You are about to measure the resistance of an electro-mechanical

relay. What is the appropriate instrument to use to do the task?
A. Voltmeter
B. Ammeter
C. Ohmmeter
D. Galvanometer

7. It consists of several individual terminals arranged in a long strip

which is used to secure and/or terminate wires.
A. Terminal blocks
B. Terminal lugs
C. Terminal Screws
D. Terminal Nuts

8. It is a type of hard hat which is intended to reduce the force of impact

resulting from a blow to the top of the head.
A. Type 1
B. Type 2
C. Class A
D. Class B

9. It must be used when there is danger of falling or rolling objects,

objects piercing sole, or feet exposed to electrical hazards.
A. Eye Protection
B. Head Protection
C. Foot Protection
D. Face Protection
10. These are devices used to protect the employees from injury or illness
resulting from contact with workplace hazards.
A. Professional Protective Equipment
B. Personal Protective Equipment
C. Personal Protective Element
D. Professional Protective element

11. It states that in a circuit made up of pure resistances current varies

directly with voltage and inversely with resistance.
A. Electron Theory
B. Ohm’s Law
C. Law of Conservation of Voltage
D. Law of Conservation of Current

12. The resistance of an electrical conductor increase with

_______________.
I. an increase in ambient temperature
II. decrease in cross-sectional area
III. an increase in conductor length

A. I only
B. I and II only
C. III only
D. I, II, and III

13. If 36 resistances each 72 Ω are connected in parallel, the total

resistance would be _______________ Ω.
A. 648
B. 324
C. 9
D. 2

14. It is a type of wound-field motor with a field windings connected in

parallel to the armature winding of the motor.
A. Shunt
B. Series
C. Compound
D. Universal

15. What is the first step in identifying the untagged terminal leads of
nine leads out three-phase induction motor?
A. Determine the starting and running winding
B. Determine whether the motor is connected in wye or delta
C. Check the resistance of terminal leads
D. Label the terminal leads
16. Are also known as signaling devices.
A. Input Devices
B. Output Devices
C. Processing Devices
D. Protective Devices

17. An off delay timer contact will change state

A. Upon energizing the coil
B. Upon de-energizing the coil
C. Depending on the setting of the time
D. None of these

18. Thermal Overload relay is an example of _______________.

A. Input Devices
B. Processing Devices
C. Protective Devices
D. Output Devices

19. A device or group of devices that serves to govern in some

predetermined manner the performance of an electric motor.
A. switch
B. feeder
C. motor controller
D. control circuit

20. The most common type of motor starting is _______________.

A. full-voltage starters
B. reduced voltage starters
C. auto-transformer starters
D. Wye-delta starters

21. Autotransformer reduced-voltage starters provide _______________.

A. lowest starting torque per ampere of line current
B. moderate starting torque per ampere of line current
C. highest starting torque per ampere of line current
D. A and B

22. Which of the following is a reduced-voltage starting?

A. Direct-on-Line Starters
B. Primary Resistance Starters
C. Forward Reverse Starters
D. Start Stop Jog Starters

23. What would you do to reverse the rotation of a three-phase motor?

A. Turn it around
B. Reverse two of the four leads
C. Reverse all leads
D. Reverse any two of the three leads
24. The “3” in a 3/2 way directional valve refers to?
A. Number of positions
B. Number of ports
C. Number of cylinder
D. Number of valves

25. Transformer is use to _______________.

A. Reduces the main voltage
B. Converts the ac voltage to dc voltage.
C. Maintain constant voltage at the output
D. None of these

26. Which of the following points should be observed while working with
electro-pneumatic systems?
I. Use tools in operating electrical limit switch during fault
finding
II. Switch off the air and voltage supply before disconnecting
the circuit
III. Do not exceed the permissible working pressure
IV. Use only voltages of ≥ 24 V

A. I and II only
B. III and IV only
C. I, II, and III only

D. I, II, III, and IV

27. It is used to lubricate the compressed air with a fine fog of oil.
A. Oil-fog lubricator
B. Oil-fog regulator
C. Oil lubricator

D. Fog regulator

28. Type of cylinder wherein compressed air is applied to only one side.

A. Double Acting Cylinder
B. Dual Acting Cylinder
C. Triple Acting Cylinder

D. Single Acting Cylinder

29. The normal and actuated positions of valves are represented by

_______________?
A. Boxes
B. Lines
C. Circles
D. Triangles
30. A source transistor type output module will have a _______________
common.
A. positive
B. negative
C. either positive or negative
D. neither positive nor negative

31. A sink transistor type output module will have a ________________

common.
A. positive
B. negative
C. either positive or negative
D. neither positive nor negative

32. It is the heart of a PLC.

A. IM
B. OM
C. PS
D. CCU

33. Which among the following situations exemplified the Seiri in 5 S?

A. Taking out and disposing small pieces of wire
B. Arranging tools
C. Sweeping the floor
D. Cleaning work area

34. Keeping the workplace clean as well as neat.

A. Seiri
B. Seiton
C. Seiso
D. Seiketsu

35. Maintaining the workplace in high standard housekeeping

A. Seiri
B. Seiton
C. Seiso
D. Seiketsu

36. Shitsuke is to Self-Discipline as Seiketsu is to ___________.

A. Sweep
B. Systematize
C. Standardize
D. Sort
37. When should inspection and testing of installed mechatronics devices
be done?
A. After supplying power
B. Before supplying power
C. During initial start
D. After the installation

38. What is the primary basis in preparing report on installation and

testing of equipment?
A. Company’s procedures/policies
B. Worker’s procedures/policies
C. A and B
D. Co-worker’s procedures/policies

39. How could you say that the installed circuit is a good circuit?
A. The needle pointer deflects and reads zero
B. The needle pointer does not deflect
C. The needle pointer deflects to the right but not to zero
D. The needle pointer is in infinity

40. What is the first step in resistance checking of installed circuit?

A. Connect the test probes to the supply line
B. Calibrate the ohmmeter range
C. Set the range selector knob in ohmmeter range
D. Press the start button
ANSWER KEY

I. True or False
1. T
2. F
3. F
4. T
5. F
6. T
7. F
8. F
9. F
10. T

II. Multiple Choice

1. B 21. C
2. D 22. B
3. D 23. D
4. C 24. B
5. A 25. A
6. C 26. C
7. A 27. A
8. A 28. D
9. C 29. A
10. A 30. A
11. B 31. B
12. D 32. D
13. D 33. A
14. A 34. C
15. B 35. D
16. A 36. C
17. B 37. D
18. C 38. A
19. C 39. C
20. A 40. C