0% found this document useful (0 votes)
279 views3 pages

Oscilloscope & Function Generator Operation: Department of Electrical Engineering Network Analysis Lab

This lab report summarizes an experiment on learning the operation of an oscilloscope and function generator. The experiment was conducted by Usairum Mirza and Noman Ali Javed. The objective was to become familiar with how to use an oscilloscope and function generator. The report describes the theory of operation for an oscilloscope, digital multimeter, function generator, and DC power supply. It explains how to measure voltage, current, and resistance using these devices. The conclusion states that the lab introduced the basic functions and workings of an oscilloscope, function generator, and DMM.

Uploaded by

Usairum Mirza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
279 views3 pages

Oscilloscope & Function Generator Operation: Department of Electrical Engineering Network Analysis Lab

This lab report summarizes an experiment on learning the operation of an oscilloscope and function generator. The experiment was conducted by Usairum Mirza and Noman Ali Javed. The objective was to become familiar with how to use an oscilloscope and function generator. The report describes the theory of operation for an oscilloscope, digital multimeter, function generator, and DC power supply. It explains how to measure voltage, current, and resistance using these devices. The conclusion states that the lab introduced the basic functions and workings of an oscilloscope, function generator, and DMM.

Uploaded by

Usairum Mirza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Department of Electrical Engineering

Network Analysis Lab

Lab Report: 01

Oscilloscope & Function Generator


Operation
Group member Names: Usairum Mirza, Noman Ali Javed
Roll Number: 160363, 150409
Objective:
To become familiar with the operation and use of the oscilloscope and function generator.

Apparatus:
 Oscilloscope
 Digital Multimeter
 Function Generator
 DC power supply

Theory of operation:
In this lab we learned about the function and usage of
a) Oscilloscope: Oscilloscope is the most important instrument available to the Practicing
Technician or engineer. It permits the visual display of a signal that can reveal a range of
information regarding the operating characteristics of a circuit or system that is not available with
a standard multimeter.
It has 2 channel labeled channel 1 and channel 2 and two basic knobs one for volts per division
and other for time/Period. For finding voltage and period of a waveform following formula
should be adopted.
Signal voltage (unknown) = voltage sensitivity V/cm × deflection cm
Period of waveform = horizontal sensitivity (s/cm) × deflection (cm)

b) Digital Multimeter: A multimeter or a multitester, also known as a VOM (volt-ohm-


milliammeter), is an electronic measuring instrument that combines several measurement
functions in one unit. A typical multimeter can measure voltage, current, and resistance.
Circuit For connecting DMM:

Figure 1 to measure current, the circuit must be broken to allow the ammeter to be connected in series
Figure 2 Circuit After Connecting a Voltmeter

Figure 3 Circuit after connecting an Ohmmeter

c) Function Generator: The function Generator is a supply that typically provides a sinusoidal,
square-wave, and triangular waveform for a range of frequencies and amplitudes. Although the
frequency of the function generator can be set by the dial position and appropriate multiplier, the
oscilloscope can be used to precisely set the output frequency.
We can change the waveform to 3 types sin, triangular and rectangular. Adjust frequency,
Amplitude and offset accordingly explained in the video lecture.
d) Regulated DC Power Supply: A regulated power supply is an embedded circuit; it converts
unregulated AC into a constant DC. With the help of a rectifier it converts AC supply into DC. Its
function is to supply a stable voltage, to a circuit or device that must be operated within certain
power supply limits. The output from the regulated power supply may be alternating or
unidirectional, but is nearly always DC

Conclusion:
In this lab we were introduced to basic function and working of oscilloscope, Function Generator and
DMM. Oscilloscope is used to see waveform in its window we can give our desired signal from function
generator and measure voltage current and resistance from digital multimeter.

You might also like