Scribd
Upload
73 views6 pages

Bipolar Junction Transistor

1. The minimum value of IB that will produce saturation in the given transistor circuit is 0.25 mA. 2. Common faults in BJT-based circuits include opens or shorts internal to the transistor, open bias resistor(s), and external opens and shorts on the circuit board. 3. The dc load line on a family of collector characteristic curves of a transistor shows the active region of operation.

Uploaded by

Denver G. Magtibay
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
73 views6 pages

Bipolar Junction Transistor

1. The minimum value of IB that will produce saturation in the given transistor circuit is 0.25 mA. 2. Common faults in BJT-based circuits include opens or shorts internal to the transistor, open bias resistor(s), and external opens and shorts on the circuit board. 3. The dc load line on a family of collector characteristic curves of a transistor shows the active region of operation.

Uploaded by

Denver G. Magtibay
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 6

1. Refer to this figure. D.7.4 mA 7.

When a transistor is used


Determine the minimum as a switch, it is stable in
value of IB that will produce 4. What is the ratio of IC to which two distinct regions?
IB?
saturation.
A.saturation and active
A. DC
B.active and cutoff
B. hFE
C.saturation and cutoff
C. DC
D.none of the above
D.either DC or hFE, but not
8. The term BJT is short for
DC
A.0.25 mA
A.base junction transistor.
5. For normal operation of a
B.5.325 A pnp BJT, the base must be B.binary junction transistor.
________ with respect to the
C.1.065 A
emitter and ________ with C.both junction transistor.
D.10.425 A respect to the collector.
D.bipolar junction transistor.
2. A transistor amplifier has a A.positive, negative
9. For a silicon transistor,
voltage gain of 100. If the
B.positive, positive when a base-emitter junction
input voltage is 75 mV, the
is forward-biased, it has a
output voltage is: C.negative, positive nominal voltage drop of
A.1.33 V D.negative, negative A.0.7 V.
B.7.5 V 6. Refer to this figure. The B.0.3 V.
value of VBC is:
C.13.3 V
C.0.2 V.
D.15 V
D. VCC.
3. Refer to this figure. If VCE =
10. A certain transistor has
0.2 V, IC (sat) is:
IC= 15 mA and IB = 167 A;
DC is:
A.9.2 V
A.15
B.9.9 V
B.167
C.–9.9 V
A.0.05 mA C.0.011
D.–9.2 V
B.2.085 mA D.90

C.1.065 mA
11. Refer to this figure. The 14. Refer to this figure. The C.100 k
value of VCE is: value of VBE  is:
D.150 k

17. The value of DC

A.is fixed for any particular


transistor.

B.varies with temperature.


A.9.9 V
A.0.6 V
C.varies with IC.
B.9.2 V
B.0.7 V
D.varies with temperature
C.0.7 V
C.1.2 V and IC.
D.19.3 V
D.0.079 V 18. A transistor data sheet
12. What does DC vary usually identifies DC as
with?
A. hre.
15. What are the two types
A. IC
of bipolar junction B. hFE.
B. ºC transistors?
C. IC.
C.both IC  and ºC A.npn and pnp
D. VCE.
D. IC, but not ºC B.pnn and nnp
19. What is the ratio of IC  to
13. A BJT has an IB  of 50 A C.ppn and nnp IE?
and a DC of 75; IC  is: D.pts and stp
A. DC
A.375 mA
16. In this circuit DC = 100
B. DC / ( DC + 1)
B.37.5 mA and VIN  = 8 V. The value of
RB  that will produce C. DC
C.3.75 mA saturation is:
D.either DC / ( DC + 1)
D.0.375 mA
or DC, but not DC

20. Refer to this figure. The


value of DC = 100 and VIN 

A.92 k

B.9.1 M
= 8 V. Determine IC (sat). C. VCE (max) > VCE A.opens or shorts internal to
the transistor
D.none of the above
B.open bias resistor(s)
24. The magnitude of dark
current in a phototransistor C.external opens and shorts
usually falls in what range? on the circuit board

A.18 mA A.mA D.all of the above

B.7.92 mA B.μA 28. The dc load line on a


family of collector
C.1.8 mA C.nA characteristic curves of a
D.pA transistor shows the
D.8 A

25. A 35 mV signal is applied A.saturation region.


21. Which of the following is
true for an npn or pnp to the base of a properly B.cutoff region.
transistor? biased transistor with an r'e 
= 8   and RC  = 1 k  . The C.active region.
A. IE  = IB  + IC output signal voltage at the
collector is: D.all of the above
B. IB  = IC + IE 
29. Refer to this figure.
A.3.5 V
C. IC = IB  + IE  Determine the minimum
B.28.57 V value of VIN from the
D.none of the above
following that will saturate
C.4.375 mV this transistor.
22. What is the order of
doping, from heavily to D.4.375 V
lightly doped, for each
region? 26. What is (are) general-
purpose/small-signal
A.base, collector, emitter transistors case type(s)?
B.emitter, collector, base A.TO-18
C.emitter, base, collector B.TO-92 A.13.21 V

D.collector, emitter, base C.TO-39 B.12.51 V

23. In what range of voltages D.TO-52 C.0.7 V


is the transistor in the linear
region of its operation? E.all of the above D.9.4 V

A.0 < VCE 27. What is (are) common


fault(s) in a BJT-based
B.0.7 < VCE < VCE (max) circuit?

You might also like