Z300CL Trouble Shooting Guide

Mario Chen
7/6/2015 Mobile Communication BD3-
BD3-SYS Dept.1-
Dept.1-Sec.2
 APPEARANCE
LIGHT SENSOR FRONT CAMERA
SPEAKER SPEAKER

2
 APPEARANCE
POWER BUTTON REAR CAMERA

VOLUME UP
BUTTON

VOLUME DOWN
BUTTON

POGO PIN FOR AUDIO DOCK SIM/SD CARD SLOT

MAIN BOARD

AUDIO JACK

USB CONNECTOR

DOCK BOARD SIM SD 4

AUDIO CODEC
U2801 / ALC5648
5
APPEARANCE
MODEM
U5801 / PMB9930
SOC
U301 / Z3560

EMMC
U1601 AUDIO CODEC
U2801 / ALC5648
6
APPEARANCE

CADIZ
U2000 / CXD4756

7
 APPEARANCE
USB AUDIO JACK MICROPHONE ECOMPASS + ACCELEROMETER
CON2101 U2901 U2903 U1702

SD CONN.
CON2301
VOLUME - VOLUME+
BUTTON BUTTON

POWER
BUTTON

SIM CONN.
CON2302
DOCK CONN.
CON2103 LIGHT SENSOR
U1701

FRONT CAMERA
8
SYSTEM BLOCK DIAGRAM

9
 ISSUE LIST
• Boot Failure • I2C:Front Camera Fail
• Boot up but No display • Speaker Test Fail
• USB Link Fail • Board MIC Test Fail
• Query PCBID Fail • I2C:E-Compass/Accelerometer
Fail
• Key Test Fail • I2C:Light Sensor Fail
• BT ON/OFF Fail • Hall Sensor Test Fail
• WiFi ON/OFF Fail • I2C:Touch IC Status Fail
• GPS ON/OFF Fail • Headset Test Fail
• I2C:Audio Codec Fail • SIM Test Fail
• I2C:Charger Status Fail • SD Test Fail
• I2C:Gauge IC Fail • POGO Pin Test Fail
• I2C:Rear Camera Fail
10
 Boot Fail
• Check battery voltage is higher than 3.5V
• Check power on sequence (system/PMIC)
– Check PWRBTN_N voltage (press down -> 0V), (release -> 1.3V)
– Check V_3P30_VDD3, V_VNNAON, V_1P80_VDD1, V_3P30_VUSBPHY,
V_1P24_VDD2, V_1P00_VREFSOC, V_VNN, V_VCC0, V_VCC1 are ready
– Once all of the power rails are ramp up, PMIC_PWRGOOD will be set
to high(1.8V), finally, PMIC_RESET_N also goes to 1.8V.

• Check eMMC Status

11
System Power On Sequence

12
PMIC Power On Sequence

13
eMMC Schematics

14
 Boot Up But No Display
• Panel & Connector
– Check LCD Panel
– Check LCD FFC & Connector CON2000
• CADIZ
– Check LCM_EN, CADIZ_RST_N, CDZ_ID are High
– Check V_CADIZ_AVDD_1P2, V_CADIZ_DVDD_1P2,
V_CADIZ_DVDD_1P8, SYSCLK_CAD are ready.
• LCM
– Check LCM_EN, LCM_XR ES_N are High
– Check LCM_ID0, LCM_ID1 are High.
– Check VDD_LCM_3V3, V_LCD_1P8 are ready.
15
CADIZ System Block Diagram

16
 USB Link Failure
• Check USB Cable
• Check USB_SEL is High
• Check USBSEL is High
• Check V_3P30_VUSBPHY is 3.3V
• Check VUSBPHYIN (PC1406 pin1) is 1.8V
• Good Soldering at L2101

17
USB/Dock Switch

18
 Query PCBID Failure
• Check voltage level at HW_ID0/1/2,
PJ_ID0/1/2, PJ_SUB_ID0/1.

19
 Key Test Failure
• Check good soldering on SW2602, SW2603,
SW2601
• VOLUME_UP_SOC, VOLUME_DOWN_SOC are
Low when up/down key pressed down.
• VOLUME_UP_SOC, VOLUME_DOWN_SOC are
High when up/down key released.
• PWRBTN_N is Low when power key pressed
down.
• PWRBTN_N is High when power key released.
20
Button

21
 BT ON/OFF Fail
• Check VBAT_WL_SR_43S is equal to VBATT
• Check VDD_WL_LDO_3V3_43S is 3.3V
• Check VDD_WL_LNLDO_1V2_43S is 1.2V
• Check BT_REG_ON_43S is High when BT is
turned on
• Check UART (BT_UART_RXD_43S,
BT_UART_TXD_43S) are working

22
 WiFi ON/OFF Fail
• Check VBAT_WL_SR_43S is equal to VBATT
• Check VDD_WL_LDO_3V3_43S is 3.3V
• Check VDD_WL_LNLDO_1V2_43S is 1.2V
• Check VDD_WL_CLDO_1V2_43S is 1.2V
• Check VDD_WL_CBUCK_1V35_43S is 1.35V
• Check VDD_WL_IO_1V8_43S is 1.8V
• Check WL_REG_ON_43S is High when WiFi is turned on
• Check SDIO bus (WL_SDIO_CLK_43S,
WL_SDIO_CMD_43S, WL_SDIO_D0_43S) are working

23
BT/WiFi System Block Diagram

24
 GPS ON/OFF Fail
• Check VDD_GPS_3V3_52_1 is 3.3V
• Check VDD_GPS_IO_1V8_52_1 is 1.8V
• Check VDD_GPS_AUX_1V8_52_1 is 1.8V
• Check VDD_GPS_CORE_1V1_52_1 is 1.1V
• Check VDD_GPS_GRF_1V2_52_1 is 1.2V
• Check GPS_POWER_ON_52_1 is High when GPS is
turned on
• Check GPS_TCXO_26M_52_1 is 26MHz

25
GPS PMU Block Diagram

26
 I2C Audio Codec Error
• Check battery voltage is higher than 3.5V
• Check good soldering at L2801, U2801
• Check DBVDD, CPVDD, AVDD are 1.8V
• Check I2C bus(CDC_I2C_SCL, CDC_I2C_SDA) is
working

27
 I2C Charger Status Error
• Check USB cable
• Check good soldering at PR1505, PR1504
• Check USB_VBUS_IN, CHG_USBIN_S voltage
are above 4.5V
• Check CHG_ACOK_N, USBIN_ACOK_N are low
when CHG_USBIN_S is above 4.5V
• Check I2C bus (CHG_SCL, CHG_SDA) is working

28
Charger related schematics

29
 I2C Gauge Status Error
• Check Battery voltage is above 3.5V
• Check good soldering at PR9605, PR9606, PR9608
• Check I2C bus(BL_GAUGE_I2C_SDA,
BL_GAUGE_I2C_SCL) is working

30
 I2C Rear Camera Error
• Check camera module, connector(CON1900)
• Check good soldering at CON1900, RN1902, RN1903,
RN1904
• Check V_AVDD_MCAM is 2.8V
• Check V_DVDD1P2_MCAM1 is 1.2V
• Check V_VDDIO_MCAM is 1.8V
• Check V_AFVDD_MCAM is 2.9V
• Check MCAM_PWRDN is High
• Check MCAM_MCLK is 19.2MHz
• Check I2C bus(MCAM_SCL, MCAM_SDA) is working

31
 I2C Front Camera Error
• Check camera module, connector(CON1901)
• Check good soldering at CON1901, RN1900,
RN1901
• Check V_AVDD_FCAM is 2.8V
• Check V_VDDIO_FCAM is 1.8V
• Check FCAM_PWRDN is High
• Check FCAM_RESET is High
• Check FCAM_MCLK is 19.2MHz
• Check I2C bus(FCAM_SCL, FCAM_SDA) is working
32
 Speaker Test Fail
• Check Left/Right Channel Speaker
• Check good soldering at U2801, R2832, R2833,
R2834, R2835
• Check battery voltage is higher than 3.5V
• Check SPK_OUT_R-_R/SPK_OUT_R+_R are
working when playing music
• Check SPK_OUT_L-_R/SPK_OUT_L+_R are
working when playing music
33
 Board Mic Test Fail
• Check good soldering at U2903, R2922, R2923,
C2910, C2915
• Check CDC_MIC_BIAS2 voltage is higher than 2.8V

34
 I2C E-Compass/Accelerometer Status
Error
• Check good soldering at U1702, R1703, R1704,
R1707, R1706.
• Check BOSCH_VDDIO, BOSCH_VDD are 1.8V
• Check I2C bus(SENSOR_I2C_SDA,
SENSOR_I2C_SCL) is working
• Check ACC_INT_N is Low when Accelerometer
is working
• Check COMPASS_INT_N is Low when e-
compass is working
35
E-Compass/Accelerometer Schematics

36
 I2C Light Sensor Test Fail
• Check good soldering at U1701, R1702
• Check ALS_INT_N is Low when light sensor is working
• Check I2C bus(SENSOR_I2C_SCL, SENSOR_I2C_SDA)
is working

37
 Hall Sensor Test Fail
• Check good soldering at U1704
• Check HALL_IRQ_N is low when hall sensor is
working

38
 I2C Touch IC Status Error
• Check V_TP_1P8 is 1.8V
• Check V_VSYS_TP is equal to VSYS
• Check TS_RST_OUT_N is High
• Check TS_INT_N is low when touch detection
• Check I2C bus(TP_SCL, TP_SDA) is working

39
 Headset Sound Test Fail
• Check Headset Status
• Check good soldering at J2901, R2911, R2912,
L2902, L2903, R2917, R2915
• Check Audio Codec Status
• Check DB_SW_INT is less than 3.0V
• Check JACK_DET_FILTR is low when headset is
inserted.
• Check HPOUTR2/HPOUTL2 is working when
playing music

40
 Headset Record Test Fail
• Check Headset Status
• Check good soldering at L2901, R2906, C2903,
C2812, C2813, C2814, C2815
• Check Audio Codec status
• Check JACK_DET_FILTR is low when headset is
inserted.
• Check CDC_MIC_BIAS1 is Higher than 2.8V

41
Audio Jack Schematics

42
Headphone/UART Switch

43
 uSIM Test Fail
• Check uSIM card
• Check good soldering at CON2302, R2301, R2302,
R2303, D2314, D2315
• Check VSIM1_VAR when uSIM card is inserted
• Check SIM1_CD_CONN is High when uSIM card is
inserted
• Check SIM1_RST is High when uSIM card is inserted
• Check SIM1_CLK , SIM1_IO when uSIM card is
inserted

44
SIM CONN

45
 Micro SD Test Fail
• Check uSD card
• Check good soldering at CON2301, U2302, PU9901,
PU9901, R2308
• When uSD is inserted.. Check
– SDIO_PWR_EN is High
– VDD3_SD_SW is 3.3V
– SDIO_0_PD# is High
– SDIO_0_CD# is Low
• Check SDIO_0_DATAx_CON, SDIO_0_CMD_CON,
SDIO_0_CLK_CON

46
SD Schematics

47
 POGO Pin Test Fail
• Check good soldering at CON2103, L2102,
Q2101, U2101, R2105, R2106, Q2103, R2102
• When pseudo dock is inserted.. Check
– USB_SEL is low
– DOCK_IN_N is low
– DCIN_ACOK_N is low
– DC_DOCK_IN voltage is higher than 4.5V

48
Dock Conn

49
Thank You !!

50