Scribd
Upload
91 views2 pages

Electronics 2. E Group: 1 2 3 4 5 6 7 8 9 10 A B C D

1. The document contains a 10 question midterm exam on electronics and PLL circuits with multiple choice answers for each question. 2. It also contains 3 circuit analysis problems - on rectification, buck converter design, and PLL analysis - with multiple parts to each problem requiring calculations. 3. Additional information provided includes the test date, available time to complete the exam, grading scale, and sample data for one of the circuit analysis problems.

Uploaded by

usman akbar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
91 views2 pages

Electronics 2. E Group: 1 2 3 4 5 6 7 8 9 10 A B C D

1. The document contains a 10 question midterm exam on electronics and PLL circuits with multiple choice answers for each question. 2. It also contains 3 circuit analysis problems - on rectification, buck converter design, and PLL analysis - with multiple parts to each problem requiring calculations. 3. Additional information provided includes the test date, available time to complete the exam, grading scale, and sample data for one of the circuit analysis problems.

Uploaded by

usman akbar
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Small questions.

There is one correct answer for each question. Correct solution in the table below is worth 1 point per question. Electronics 2. E group
Mid-term test 2
1.) In a PLL the phase difference is December 32. 3020.
A: (υ1- υ2)*KPD B: Uc*Ko C: UPD/KPD D: (υ1- υ2)*Ap

2.) The dimension of KO: Name, Neptun-code Room Signature of supervisor


A: [V] B: [1] C: [V/Hz] D: [Hz/V] Joe Test moodle dr. X. X.
3.) The dimension of Ap:
A: [V] B: [1] C: [V/Hz] D: [Hz/V] --- 1. 2. 3. Small Σ grade
Max. point 4 6 4 10 24 ---
4.) This signal is proportional to the input frequency at steady state: Points earned
A: UPD B: UC C: UC/(υ1- υ2) D: non of them
Corrector --- ---
5.) A serial R-L-C filter could be used as band stop filter, if the output is the voltage on
A: R B: R-L C: C D: L-C
Available time: 15+60 minutes. The marks will be given according to the following limits:
6.) What kind of converters is the circuit below: 0-9 points failed (1)
A: Boost B: Buck C: Buck-boost D: Inverter 10-12 points pass (2)
13-15 points satisfactory (3)
16-19 points good (4)
7.) What is the correct relation during normal operation of the average of the 3 voltages: 20-24 points excellent (5)
A: Uin>Usw≈Ud B: Uin≈Usw<Ud C: Uin<Usw=Ud D: Uin≈Usw>Ud

8.) What is the correct relation during normal operation of the average of the 3 currents: 1.) We are rectifying the sinusoidal grid voltage with a 1 phase 2 way 2 pulse rectifier which is built from 4 diode.
A: Iin≈ID>Id B: Iin≈ID<Id C: Iin<ID=Id D: Iin>ID≈Id The output is filtered by a capacitor. The input voltage is 230V 50Hz.
a) What is the expected value of the output voltage (with 10% tolerance).
9.) How depends the output voltage ripple on the switching frequency? b) The load current is Iout=10A. What is the output power?
A: f B: f2 C: 1/f D: 1/ f2 c) We measure 30Arms at the input of the rectifier. What is cos(phi)?
d) What is the power factor?
10.) What is the maximal voltage on the transistor?
A: Uin B: Ud C: Uin-Ud D: Ud-Uin

iL 1 2 3 4 5 6 7 8 9 10
uL iD id (Id)

L
A
D +
Uin iSW C ud (Ud) Rd
SW - B
ic

C
D
2.) Design a Buck (Step down) converter with the following parameters: Vin=24V, Vout=10V, Iout=10A, 3.) PLL
Tsw=100µs, ΔIL=25% of Iout, ΔVout=0.2% of Vout. a.) In the following PLL schematic assign the voltages to the circuit’s the points:
a.) What is the maximal voltage on the transistor? Uc, UPD
b.) What is the peak current on the transistor? R1-left, R1-right, R3-left, R3 right, C2-left, C2-right
c.) Calculate the L and C parameters of the converter! b.) KO! (0.5p)
d.) What is the RMS current of the choke? c.) KPD! (0.5p)
e.) Estimate the power dissipation on the diode! The diode’s forward characteristic could be d.) Determine the upper limit of the hold-in range!
approximated with 0.6V+i*0.1Ohm. e.) Estimate the cut-off angular frequency of the control loop!
f.) How much is the cut-off (resonance) frequency of the L-C filter? R4

R3 C2
U1 R1 - R6
+ -
U2 +
-
+
R2 +
R5
-
C1

Data: XOR: UOH=5V és UOL=0V, R1=10k, R2=1k, C1=20nF, R3=R4=R5=R6=10k, C2=2nF,


UH=1V.

You might also like