Scribd Logo
Upload

Welcome to Scribd!

  • 1K views

    RF Demo Kit Quick Start Guide

    Uploaded by

    Kadir Mariño Abreu
    Two steps must be performed before testing the RF demo kit: 1. Connect the two 20cm SMA to IPEX adapter cables to the NanoVNA-F machine. 2. Recalibrate the machine using the circuits on the test board and save the parameters to SAVE 0. The document then provides instructions for testing 18 different circuits on the RF demo kit board to analyze resistance, capacitance, inductance, and various filter circuits.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    RF Demo Kit Quick Start Guide

    Uploaded by

    Kadir Mariño Abreu
    1K views1 page
    Two steps must be performed before testing the RF demo kit: 1. Connect the two 20cm SMA to IPEX adapter cables to the NanoVNA-F machine. 2. Recalibrate the machine using the circuits on the test board and save the parameters to SAVE 0. The document then provides instructions for testing 18 different circuits on the RF demo kit board to analyze resistance, capacitance, inductance, and various filter circuits.

    Original Title

    Rf_Demo_Kit_Quick_start_guide_v2.0

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Two steps must be performed before testing the RF demo kit: 1. Connect the two 20cm SMA to IPEX adapter cables to the NanoVNA-F machine. 2. Recalibrate the machine using the circuits on the test board and save the parameters to SAVE 0. The document then provides instructions for testing 18 different circuits on the RF demo kit board to analyze resistance, capacitance, inductance, and various filter circuits.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    1K views1 page

    RF Demo Kit Quick Start Guide

    Uploaded by

    Kadir Mariño Abreu
    Two steps must be performed before testing the RF demo kit: 1. Connect the two 20cm SMA to IPEX adapter cables to the NanoVNA-F machine. 2. Recalibrate the machine using the circuits on the test board and save the parameters to SAVE 0. The document then provides instructions for testing 18 different circuits on the RF demo kit board to analyze resistance, capacitance, inductance, and various filter circuits.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    RF Demo Kit Quick start guide

    Two steps must be performed before testing:


    Step 1. Connect the two 20CM SMA to IPEX Designed By: BH5HNU & June
    adapter cables to the NanoVNA-F machine. Date: 15 July 2020
    Step 2. Recalibrate the machine using the 13 Short, 14 Open, Release: 2.0
    15 Load, and 16 Thru circuits on the test board,
    and save the parameters to SAVE 0.

    Circuit 1. RLC Series-parallel circuit Circuit 2. RLC Series-parallel circuit Circuit 3. 33 Ohm Resistance Circuit 4. 75 Ohm Resistance Circuit 5. 6.5MHz Ceramic Trap
    Display S11 Smith Chart, START=50kHz, Display S11 Smith Chart, START=50kHz, Display S11 Smith Chart & SWR, Display S11 Smith Chart & SWR, Display S21 LOGMAG,
    STOP=600MHz STOP=600MHz START=50kHz, STOP=1000MHz START=50kHz, STOP=1000MHz START=5.5MHz, STOP=7.5MHz

    Circuit 6. 10.7MHz Ceramic filter Circuit 7. RC series circuit Circuit 8. LC series circuit Circuit 9. Capacitance Circuit 10. Inductance
    Display S21 LOGMAG, Display S11 Smith Chart, Display S11 Smith Chart, Display S11 Smith Chart, Display S11 Smith Chart,
    START=9.7MHz, STOP=11.7MHz START=50kHz, STOP=300MHz START=50kHz, STOP=600MHz START=50kHz, STOP=300MHz START=50kHz, STOP=30MHz

    Circuit 11. 400MHz Low-pass filter Circuit 12. 500MHz High-pass filter Circuit 13. Short Circuit 14. Open Circuit 15. 50 Ohm Load
    Display S21 LOGMAG, START=100MHz, Display S21 LOGMAG, START=1MHz, Display S11 Smith Chart, Display S11 Smith Chart, Display S11 Smith Chart,
    STOP=600MHz, SCALE=2dB STOP=1000MHz, SCALE=10dB START=50kHz, STOP=1000MHz START=50kHz, STOP=1000MHz START=50kHz, STOP=1000MHz

    RF Demo Kit MADE IN CHINA


    For VNA Testing
    More Detail : deepelec.com/rf-demo-kit

    deepelec.aliexpress.com
    groups.io/g/nanovna-f
    Facebook Group : NanoVNA-F
    Circuit 16. Thru Circuit 17. 10dB Attenuation Circuit 18. 3dB Attenuation
    Display S21 LOGMAG, Display S21 LOGMAG, Display S21 LOGMAG, Hangzhou Minghong Electronic Technology Co., Ltd. www.deepelec.com
    START=50kHz, STOP=1000MHz START=50kHz, STOP=1000MHz START=50kHz, STOP=1000MHz

    You might also like