RDAC XF

RDAC XF and RDAC XF MAP

RDAC XF MAP version has a map sensor fitted.

Input Connections

TC 1 to 12 Inputs for use with thermocouple temperature probes. Typcally

used for EGT probes (K-types) and CHT probes (K or J types).
Can also be used for other types of temperature monitoring
depending on abilities of connected system.
GND Grounding point. Connected to the engine block, also used as
ground for sensors not electrically connected to the engine itself
such as flow senders and current senders.
OIL P Oil pressure sender
OIL T Oil temperature sender
FUEL P Fuel pressure sender
COOL Coolant temperature sender
CURR Electrical current sender (Example: MGL magnetic current
sender)
FL 1 Fuel level sender for tank 1
FL 2 Fuel level sender for tank 2
AUX 1 & AUX 2 Auxiliary inputs. Used for example for Rotax 912/914 NTC type
CHT probes
RPM 1 Engine RPM input 1

RPM 2 Engine RPM input 2 (also used for Rotor RPM for some systems)
5V OUT 5V DC supply output. Intended only for low current users (30mA
maximum). Typically used as supply point for MGL fuel flow
senders.
FF 1 Fuel flow sender 1
FF 2 Fuel flow sender 2 (also used for tank return flow sender in a
differential flow installation)
MAP Sensor This 1/8” NPT fitting connects to an internal MAP pressure sensor
(Range: 0.2 – 2.5 Bar). Optional, fitted to RDAC XF MAP
 path
RPM 2 Ballast used when the RPM 2 signal line requires a
220 ohm ballast resister to ground
RPM 2 High Gain used when the RPM 2 signal needs a High
Gain (increases signal sensitivity
approximately by a factor 10)
RPM 1 Filter Adds a high frequency filter to the signal
path
RPM 1 Ballast used when the RPM 1 signal line requires a
220 ohm ballast resister to ground
RPM 1 High Gain used when the RPM 1 signal needs a High
Gain (increases signal sensitivity
approximately by a factor 10)
PD = pull down resister PU = pull up resister

This drawing illustrates the pull up resister circuit This drawing illustrates the pull up and pull down resister
circuit for the oil pressure

These circuits shows how the various PU switches feeds 5 volt onto the input(sense) line if
required. Please check the senders information for type and settings needed.
The 2nd circuit shows a pull down circuit that has a 100Ω load resister switched to GND.
This intended for use with the Rotax 4-20 mA oil pressure sender. The white wire is
connected to the OILP input on the RDAC XF. The OILP PD switch must be in the ON
position and the OIL PU switch must be in the OFF position.

Passive senders such as resistive temperature and pressure senders will require the pull-
up resistor to be “ON”. If you are using active senders (mostly used as electronic pressure
senders) please switch the pull-up resistor “OFF”.

Default settings for most installations (assuming the Rotax 4-20mA sender is not used):
Sensitivity gain adjust

RPM 1 MIN MAX Adjusts sensitivity of the RPM1 input

RPM 2 MIN MAX Adjusts sensitivity of the RPM2 input

Sensitivity to input signals on the RPM inputs can be adjusted over a wide range I two
switchable ranges (via the DIPSwitch selection, high and low range).

Highest sensitivity achievable is around 0.4V peak to peak in high gain and 4V peak to
peak in low gain. From this level, the trimmers can be used to reduce the gain over a very
wide range to around 50V peak to peak or higher depending on trimmer setting.

Indicator

The green LED flashes at about 1Hz during operation. If the LED is steady “ON” there is a
serious fault with the RDAC and it cannot operate. If the LED is “OFF” the RDAC is not
being supplied with power or there is a serious fault with the RDAC.

INSTALLATION

Precautions
Note that the unit is not waterproof, when installing the unit in a location where it will be
exposed to fluids it is advisable to install it in an enclosure(box)

This unit is intended for mounting on the aircraft's fire-wall,engine side.

The unit is not designed for mounting directly to the engine!
Excessive vibration , moisture and temperature extremes will damage the RDAC or
shorten its life span.

Advisory !
Once installation is complete and all setups regarding RDAC XF are done, it is important
for the dip switches and sensitivity gain adjustment to be covered (Suggestion: clear self
adhesive film)
This is to prevent dust and moisture getting in to the switches, variable resisters and other
components.
 Connection to an ENIGMA, VOYAGER or ODYSSEY G1 and G2

The RDAC XF has a RS232 connection .

This connection is only used for OEM and 3rd party
applications and is not used with any of MGL systems!

Connections to an ODYSSEY G2 and I-EFIS units

When using CAN interface, you can connect up to four RDAC XF s together.

Observe the polarity of the two CAN wires. One of the lines is called “CAN-” or “CANL”, the
other “CAN+' or “CANH” depending on equipment. It is recommended that a twisted pair
wire is used for this connection using two wire colors for ease of identification. The CAN
bus must be terminated at each end with a 120 ohm resistor. Connections from equipment
into the CAN bus (other than the ends) must only use short stubs into the bus (maximum
length of a stub should not exceed 20cm if possible).
It is OK to use only a single resistor of value 60-120 ohms if the total length of the CAN
bus is not more than two meters (6 feet).

You will need to set the RDAC SEL switches to the correct order so the ODYSSEY G2
and IEFIS depending on the number of RDAC units you have on your bus. Normally, only
a single unit is used and thus the two SEL switches are set to “off”.

Table for Rdac number

The CAN bus will typically be shared with other equipment such as AHRS, compass,
transponders etc. Please ensure that the CAN bus wiring is done to high standards and all
connections are secure as this is a critical link in your aircraft.
Thermocouple Probes Inputs (egt/cht)
TC 1 to 12 provide up to 12 channels for thermocouple temperature sensors. You can use
“K” TYPE thermocouple probes for EGT and “K or J” TYPE thermocouple probes as CHT
sensors. Note that you need to setup the EFIS so it knows the probe types and what
channels you are using.

The TC setups on Enigma, Voyager, Odyssey G1 and G2 units

are programmed to see the first TC inputs as EGTs then
followed immediately by CHTs. Example: 2 EGTs and 4 CHTs
then TC1=EGT1, TC2=EGT2, TC3=CHT1, TC4= CHT2,
TC5=CHT3 and TC6=CHT4.

On IEFIS systems you can assign TC channels as you prefer. It is however recommended
to follow the above guide by grouping your EGT probes starting at TC1, followed by a
group of CHT probes.

Depending on how many probes used for the engine ,it is possible to use open TC inputs
with probes for monitoring other components like bearings, pulleys or gearboxes ect. Note
that you need to use the screen design program to add these extra items into your desired
screen pages on the IEFIS or EFIS systems

Note that thermocouple sensors can not be sheared across two RDACs.

These are some examples of “J” and “K” type thermocouple lead colour codes
and corresponding polarity
 RDAX XF thermocouple guidelines

The thermocouple amplifier is a precision device providing full cold junction

compensation and bow voltage correction. In addition the amplifier measures
and corrects for its own errors. This results in very accurate measurements
providing you install high quality probes. Here are some guidelines:
EGT Probes: select probes that are made from 316 stainless steel and that
use glass-fiber insulated conductors. Teflon insulated conductors as found in
many cheap probes introduce errors as the insulation melts moving the
measuring point towards the mounting bolt which transfers a lot of heat to the
exhaust material. This results in under reading probes. Stay away from
probes that use simple plastic heat shrink sleeving – it does not last. Choose
probes that use a generous amount of stainless steel spring as strain relief.
The Bolt itself should be stainless as well or it will rust very quickly.
CHT probes: These are made from washers to fit spark-plug bases.
Temperatures are considerably lower so most thermocouple cables will work
without problems. The biggest area of concern should be the connection of
the thermocouple cable to the washer. This often breaks after the spark plug
has been changed a few times. Choose a probe that is suitably reinforced at
this point for a long and trouble free life.
EGT and CHT probes supplied by MGL Avionics are of highest quality. We
recommend that you consider using our probes if at all possible.
Warning: Four stroke engines produce much hotter exhaust gases compared
to two stroke engines. Do not use EGT probes made from lower grade
stainless steel (for example 310), these probes will not withstand the high
temperatures and can fail as the metal gets very soft at 800 degrees C. Many
four strokes (such as the Rotax 912) will produce exhaust gases of up to 850
degrees C.
Important installation note:
EGT and CHT probes use wire made from plain Iron and other basic metals.
As a result these probes are not able to withstand much flexing of the wires
due to engine vibrations. Avoid making nice looking coils or similar
constructions that will result in excessive vibration or flexing of the wire. Route
the cables from the probe points tightly along suitable engine mounting points
eliminating any chance of unnecessary wire flexing during engine operation.
Oil, Fuel Pressure and Coolant monitoring
Oil P connect to oil pressure sender

OIL T connect to oil temperature sender

FUEL P connect to fuel pressure sender

COOL connect to water temperature sender

It is important to know what type, range and connections are needed for the sensors.
In the EFIS and I-EFIS units menu's relating to the sensors placement can show you what
sensor types can be used.

Most sensor types are resistive. In this case you have a pull-up resistor enabled via the
DIPSWITCH array. The pull-up resistor connects to 5V DC internally. The sensors
resistance forms a resistive voltage divider to ground. The resultant voltage on the sensor
is measured and translated into a sensor reading depending on the type of sensor
connected.
Electronic pressure senders tend to output a voltage level in proportion to applied
pressure. For these devices it is recommended to switch the pull-up resistor off.

Rotax 4-20 mA oil pressure sender part no.956413. The sensor cable is approx. 3 m long
and has 3 leads. The Black lead is not to be connected and has no function. The Red lead
from the sensor has to be connected to the positive bus via a fuse or circuit breaker The
White lead (output signal) has to be connected directly to the
OILP input on the RDAC XF. The OILP PD switch must be in the on position
and the OILP PU switch must be in the off position.
This sets up the RDAC XF to measure the current
injected into the grounded 100 ohm resistor.
Current Input
CURR connect to MGL Current Sensor or any other electronic current sensor
that provides an output centered around 2.5V for zero current.

This example shows connection of the MGL Magnetic current sensor.

Connect sensor wires as indicated.

Connect the current sensor power (red wire) to the

RDAC positive supply and the black wire to GND

The magnetic current sensor can be installed in several ways depending on the current
range it is to measure. Please refer to the documentation for this sensor.
Fuel Level Inputs
FL 1 connects to fuel level sender output/signal from tank1

FL 2 connects to fuel level sender output/signal from tank 2 ( if installed)

Safety HabPRugBtRRfRIMttetyf
Aux Inputs
Rpm Inputs
RPM 1 This input connects to one of your magneto, ignition, ecu or pick-up
units

RPM 2 This input can be used to see your second mag rpm
( dual magneto, ecu or ignition units)
This input is also setup for EXTREME units to get a rotor rpm feed.
( auto gyro or helicopters) This setup is only for the Xtreme EFIS!
Typical sensitivity settings and resultant minimum signal levels:

RPM 1 shows ¼ turn RPM 1 shows mid position RPM 1 shows max position
RPM 1 High Gain on 3.5 volt (peak to peak) 0.8 volt (peak to peak) RPM 1 High Gain on RPM 1 High Gain ON 0.4 volt (peak to peak)
RPM High Gain OFF 35 volt (peak to peak) RPM High Gain OFF 8 volt (peak to peak) RPM High Gain OFF 4 volt (peak to peak)

RPM 1 High Gain RPM 1 High Gain

turned ON turned OFF

ECU units may have a digital

RPM output you may be able
to use

This a drawing of a magneto system. In this case

the RPM feeds are taken from the “P” connection
terminal.

Note that the two magnetos are connected to

the appropriate RPM inputs with a
recommended 10KΩ (10.000 ohms)
resister in line. In this case you would
have the RPM 1&2 BALLAST switches in
the OFF position.
Fuel Flow Inputs
This example is based on typical MGL flow senders:

FF1 & FF2 Connection of fuel flow sender ( Braid to GND, Red to +5 volts, Blue to FF1)
If a second fuel flow sensor is used then the braid and red wires of the second
flow sender connect as the first sender but the blue wire (signal) connects to
FF2.

Using the Fuel Flow Sender

Note the setup for Fuel flow sender

on EFIS unit ”Fuel related setup;
Fuel flow setup menu”
“Flow sender type Rdac one: Turbine

It is important to install the

fuel flow sender at an angle so that
will no bubbles can get trapped in the
impeller section. This will cause
incorrect or erratic readings.

It is also important to work out what fuel flow

to expect (generally manufacturers specify fuel usage per hour)
in order to select the right jet for the fuel flow sender unit.

Please note that the installation of the Fuel Flow sender should be done in
such a fashion that dirt or debris from the fuel tank cannot lodge inside the
flow sender. These will not block your fuel flow but may lead to the impeller
inside the sender jamming. It is usually sufficient to mount the Flow sender
AFTER the fuel filter but before the fuel pump. It is a good idea to provide a
small reservoir such as a primer bulb between the flow sender and the fuel
pump.

Using Injectors

In this injector system is the injector

has a +12volts connection but the
negative (low) side of the injector is
switched/fired by the electronic
injector control system.
For this reason in ”Fuel related
setup;
Fuel flow setup menu” the selection
should show as “Flow sender type
Rdac one: InjectorL”
Most systems used are low
triggering/firing systems
If a positive(high) switching/ firing
injector system is used then the
selection will show
“Flow sender type Rdac one: InjectorH”
Temperature monitoring connection for Rotax 582

A typical sensor connection layout

Technical data

Weight RDAC XF 340 grams

Weight RDAC XF MAP 370 grams
Power supply: 9-18V DC. DO-160 compliant to 120V/10mS pulse
CAN bus: 250kBaud, 11bit identifiers, MGL CAN bus protocol
RS232: 38400 Baud
OPT: 1250 Baud
Temperature range: -30 degrees C to +70 degrees C ambient (operation)

Thermocouple common mode range: -2V to +3V with respect to GND terminals
Thermocouple temperature range: up to 1200 degrees C (K-type probes)

Analog input pull up resistors to +5V:

AUX1, AUX2, OILT, COOL: 1500 ohms

OILP: 1000 ohms
FL1, FL2: 220 ohms

RPM inputs:
Input impedance (A/C coupled):
High gain: 15.000 ohms
Low gain: 110.000 ohms
Ballast resistor (switchable): 220ohms, 5W to GND, DC coupled