Rubber Additives - Compounding Ingredients: R. N. Datta and F. A. A. Ingham

6
Rubber Additives - Compounding Ingredients
R. N. Datta and F. A. A. Ingham
Introduction
The basic properties of rubber products are highly dependent on the elastomer(s) used in
their manufacture. However, these properties can be modified favourably through the
appropriate choice of compounding ingredients. Some are added to facilitate or accelerate
crosslinking, others improve processability and others to improve the properties of the
finished rubber product. Excluding mineral-based fillers these compounding ingredients
can be classified as follows: vulcanising agents, vulcanisation accelerators, activators of
vulcanisation, retarders and inhibitors of vulcanisation, antidegradants, antireversion
agents, plasticisers and softeners, and miscellaneous ingredients. Each class will be dealt
with in turn in the following sections.
6.1 Vulcanising agents
Materials that are able to form crosslinks between polymer chains may be generally
classified as vulcanising agents. Listed below, and described in some detail, are the curing
agents in common use together with a category of less frequently used materials.
6.1.1 Sulphur
Elemental sulphur is the most widely used vulcanisation agent in the rubber industry and
is effective in elastomers containing some degree of unsaturation. Ground sulphur is
most widely used, often referred to as rhombic sulphur or rubber makers’ sulphur. The
molecular structure of rhombic sulphur comprises an eight membered ring and is
crystalline in nature. It has a melting point of 115 °C and is soluble to a limited degree in
elastomers; for example, around 1% w/w in natural rubber at room temperature,
increasing to a level of the order of 7% at 100 °C. The relatively low solubility of sulphur
in rubber at ambient temperature is the cause of so-called ‘sulphur bloom’. It appears as
an off-white powdery coating on the surface of the uncured compound due to migration
from the bulk compound when the limit of solubility is exceeded. If present in excess it
has an unfavourable effect on the building tack of green components. Sulphur bloom
can also occur in vulcanisates but here the disadvantage is largely cosmetic.
167
Rubber Technologist’s Handbook
Sulphur bloom can be prevented by substituting rubber makers’ sulphur with so called insoluble
sulphur. This is a crystalline, polymeric form of sulphur [1] and is insoluble in solvents and
elastomers. It should be processed at temperatures not exceeding 110 °C, preferably 105 °C,
in order to prevent excessive conversion into the rhombic form. During vulcanisation it is
converted into rhombic sulphur allowing the vulcanisation process to proceed as normal.
The following advantages are claimed with regard to the use of insoluble sulphur [1, 2]:
• elimination of sulphur bloom,
• prevention of sulphur migration between green components during storage,
• reduced bin-scorch during the storage of green compounds.
6.1.2 Sulphur donors
The term ‘sulphur donor’ is a common designation for organic disulphides and higher
sulphides that are capable of providing active sulphur during the vulcanisation process
thereby generating sulphidic crosslinks. Sulphur donors can be categorised into those
that are applied as a direct substitute for free sulphur, with no major change in
vulcanisation characteristics, and those that act simultaneously as vulcanisation
accelerators (see Section 6.2). Products of the first type are, for example, dithiomorpholine
(DTDM) and caprolactam disulphide (CLD). Examples of the second category of sulphur
donors are 2-morpholinodithiobenzothiazole(MBSS), dipentamethylenethiuram-
tetrasulphide (DPTT), N-oxydiethylene-N´-oxydiethylene thiocarbamyl sulphenamide
(OTOS), tetramethylthiuram disulphide (TMTD) and its analogues. The chemical
structures of these sulphur donors are shown in Figure 6.1.
With the demand for N-nitrosamine free sulphur donors, tetrabenzylthiuram disulphide
(TBzTD; Figure 6.2) has been introduced. The prime function of TBzTD is as a secondary
accelerator but at higher loading it can also function as a sulphur donor [3].
Some additional materials are available that are capable of acting as sulphur donors; for
example, alkyl phenol polysulphide [4], bis(3-triethoxy silyl propyl) tetrasulphide [5]
(TESPT), and dialkyl dithiophosphate polysulphide [6].
6.1.3 Peroxides
Crosslinking with peroxides has been known since 1915 when Ostromyslenski disclosed
that natural rubber could be transformed into a crosslinked state with dibenzoyl peroxide
[7]. However, there was little interest in peroxide crosslinking until the development of
fully saturated ethylenepropylene copolymers in the early 1970s.
168
Rubber Additives – Compounding Ingredients
Figure 6.1 Structures of sulphur donors
Figure 6.2 Structure of TBzTD
169
The use of peroxides for the crosslinking of elastomers is limited to those that are stable
during storage, safe to handle during processing but, on the other hand, decompose
sufficiently fast at cure temperatures. In order to meet these requirements peroxides
containing tertiary carbon atoms are most suitable [8], whilst peroxy groups bonded to
primary and secondary carbon atoms are less stable. Organic peroxides that are suitable
for crosslinking elastomers are shown in Figure 6.3.
Figure 6.3 Structures of peroxides
In addition to the symmetrical peroxides, asymmetrical peroxides are also in use, as for example
tert-butyl perbenzoate, tert-butylcumyl peroxide and some polymeric peroxides [9].
A further limitation with regard to the suitability of peroxides concerns the efficiency of
crosslinking. Higher efficiencies are observed for those peroxides that form one of the
following radicals during homolytic decomposition [10] (see Figure 6.4).
The thermal stability of peroxides can be expressed in terms of their half-life (t / ). Half-
1
2
life values can be estimated in solution utilising the technique of differential thermal
analysis. These values, or more precisely the temperatures at which their half-life is
equivalent, provide an indication of practical vulcanisation temperatures [11] (see
Table 6.1).
There are a number of advantages, associated with the peroxide vulcanisation of

elastomers:
• scorch free storage of compounds,
• possibility to apply high vulcanisation temperatures without reversion,
• simple compound formulation,
• low compression set even at high cure temperatures,
170
Figure 6.4 Radicals formed during the homolytic cleavage of peroxides that are most
effective in producing crosslinks
• good electrical properties of vulcanisates,
• good high temperature vulcanisate stability,
• no discoloration of compounds.
There are, however, some drawbacks compared to sulphur vulcanisation:
• limited compounding flexibility due to the reaction of peroxides with other

compounding ingredients; for example with antioxidants, plasticisers and resins,
• sensitivity of vulcanisation reactions to oxygen,
171
Table 6.1 Typical crosslinking temperatures of crosslinking peroxides based

on their half-life
Class Example Temp. °C T1/2 = 6 Typical crosslinking
min temperature °C
Dialkyl peroxide 2,5-Bis(tert-butylperoxy) 173 180
2,5-Dimethyl-3-hexyne
2,5-Bis(tert-butylperoxy) 159 180

2,5-Dimethyl hexane
Alkyl-aralkyl Bis(tert-butylperoxy 160 180
peroxide Isopropyl) benzene
Tert-butylcumyl peroxide 160 180

Diaralkyl peroxide Dicumyl peroxide 15 5 170
Peroxy ketals Butyl 4,4-bis (tert-butyl 143 160

peroxy) valerate
1,1-Bis(tert-butyl peroxy) 129 150

3,3,5-Trimethyl
cyclohexane
Peroxy ester Tert-butylperoxy 1 46 140
benzoate
• lack of flexibility in regulating scorch and optimum cure time,
• inferior tensile, tear and flex properties,
• inferior abrasion resistance,
• frequently disturbing odours of peroxide decomposition products,
• generally higher cost.
6.1.4 Urethane crosslinking
A novel process of vulcanising olefin elastomers with sulphur was developed in the UK
by the Malaysian Rubber Producers Research Association (MRPRA) [12]. The materials
are sold under the trade name of Novor, the most popular grade being Novor 924. The
term ‘Urethane’ was applied to these materials because of their analogy with regular
172
urethane compounds, Novor 924 being an adduct of a substituted nitrosophenol and

toluene isocyanate. It is a dustless, free flowing powder containing 75% active ingredients
and 25% naphthenic oil. References have been made to its use in natural rubber (NR),
SBR and polychloroprene (CR) based compounds [13, 14].
Despite a great deal of early interest in urethane based crosslinking agents their use in
the industry has found limited application. There are several reasons for this: they are
expensive, they exhibit little scorch resistance and the materials possess limited storage
stability, absorbing moisture under humid conditions.
6.1.5 Metal oxides

Vulcanisation of CR rubber is often carried out with a combination of zinc and magnesium
oxides. Lead oxides can also be used particularly to obtain vulcanisates with low water
absorption. Polysulphide rubbers (Thiokol) and chlorosulphonated polyethylene
(Hypalon) are also vulcanised using metal oxides.
6.1.6 Other vulcanising agents

Quinone dioxime is used for the vulcanisation of butyl rubber. The presence of an oxidising
agent in the vulcanising system is necessary to convert the dioxime into p-nitrosobenzene, the
actual vulcanising agent. Lead oxide (Pb3O4; 5–10 phr) or 2,2´-dithiobis(benzothiazole) (MBTS;
4 phr) can be used.
Diamines with blocked amino groups, e.g., hexamethylene diaminocarbamate, ethylene

diaminocarbamate and dicinnamylidinehexamethylenediamine, are used to vulcanise
fluoroelastomers.
6.2 Vulcanisation accelerators

The reaction of rubber with sulphur is slow even at high temperatures. Natural rubber containing
only sulphur would require around 4 hours at 140 °C to fully vulcanise. It is not surprising then
that for the past 150 years efforts have been made to speed up the vulcanisation process.
The first such cure acceleration was accomplished by adding metal oxides to the compound,
such as those of lead, calcium and magnesium. The improvement was rather limited however
and it was not until Oenslager [15] discovered organic accelerators in 1906 that significant
improvements in the rate of vulcanisation were feasible [16]. Aniline was the first of such
organic accelerators but owing to its toxicity was soon replaced by the reaction product of
aniline and carbon disulphide [17]. This followed with the introduction of N,N´-
173
Diphenylguanidine [18] which, although still in use, is slow by today’s standards and is rarely
used alone but in combination with other accelerators.
A significant step forward was the discovery of 2-mercaptobenzothiazole (MBT) in 1921 [19].
Following the discovery of MBT, the disulphide, MBTS, was found to provide greater scorch
(premature vulcanisation generally due to excessive heat history) safety at higher temperatures.
A further important step was the discovery of sulphenamide type accelerators. They represent
the products of the oxidative condensation of thiazoles with an amine. The application of these
more effective accelerators has allowed, in general, a reduction of compound sulphur levels in
addition to increased rates of vulcanisation. This more efficient use of sulphur has led to improved
vulcanisate properties.
Triazine-based accelerators have been introduced that provide even higher crosslinking efficiency.
However, they have not established themselves as an important class of accelerators possibly
due to an unfavourable price versus performance.
There are a wide variety of accelerators available to the compounder. These include
accelerator blends of which there are well over 100. In order to rationalise this extensive
range of materials it is useful to classify them in terms of their generic chemical designation
listed below:
Sulphenamides
Thiazoles
Guanidines
Thiurams
Dithocarbamates
Dithiophosphates
Miscellaneous
Some specific chemical structures belonging to each class are shown in Sections 6.2.1 to 6.2.7.
6.2.1 Sulphenamides
A significant step forward with regard to the development of accelerators occurred in the
1930s when Zaucker and Bagemann found that sulphenamides provided a delayed action
to the vulcanisation process [20]. Today there are a number of commercially available
suphenamide-based accelerators differing in amine moiety, thereby providing control over
scorch time and cure rate. The more basic the attached amine, the shorter is the scorch
time and the higher is the cure rate. Perhaps the most widely applied sulphenamide is N-
cyclohexyl-2-benzothiazolesulphenamide (CBS) due to a good balance between scorch safety
174
and cure rate. If greater scorch safety is required the sulphenamide of choice should be N-
tert-butyl-2-benzothiazolesulphenamide (TBBS) or 2-(4-morpholinothio)benzothiazole
(MBS). TBBS not only provides greater scorch delay than CBS but also produces a vulcanisate
of higher modulus, permitting greater economy of use at equal modulus [21].
The processing safety afforded by the commonly used sulphenamides increases in the order
MBS, CBS, TBBS, whilst rate of vulcanisation decreases in the same order. Typical cure
characteristics of these sulphenamides are shown in Figure 6.5.
Sulphenamides are the preferred accelerators for steelcord skim stocks where long scorch
times are required to ensure adequate build up of the interfacial copper sulphide layer on
the surface of the brass coated steelcord prior to the onset of vulcanisation. In this way, the
Figure 6.5 Cure characteristics at 150 °C
Figure 6.6 Structures of TBBS and TBSI
175
adhesion between compound and steelcord is achieved. Relatively low cure rates are also
preferred in this application, thus TBBS is often the choice rather than CBS. Whilst MBS
exhibits the slowest cure rate and the longest scorch time, this accelerator is now out of
favour in the tyre industry due to toxicological concerns related to nitrosamine formation.
TBBS has been modified, by addition of a second benzothiazole group, to produce the
corresponding sulphenimide (TBSI). Their chemical structures are shown in Figure 6.6.
TBSI exhibits long scorch delay in addition to a slow cure rate and as such is used increasingly
in steelcord skim stocks. An additional benefit is its increased resistance to hydrolysis
compared to the sulphenamides, a noteworthy consideration when used in high temperature,
high humidity conditions.
Sulphenamides can be activated by the addition of a secondary accelerator, for example

diphenyl guanidine (DPG) or TMTD. This results in an increase in crosslinking efficiency
of the cure system, but also a decrease in processing safety (see Table 6.2).
Although as yet unavailable commercially, excellent processing safety combined with a

high cure rate and high crosslinking efficiency can be achieved by the use of a
bis(sulphenamide) and pyrimidine sulphenamide [22] (Figure 6.7).
Table 6.2 Effect of secondary accelerators on the vulcanisation

characteristics of CBS
Ingredients Formulation
1 2 3
C BS 0.6 0.6 0.6
Sulphur 2.3 2.3 2.3
DPG 0 0.2 0
TMTD 0 0 0.2
Mooney scorch, t5, min 28 24 19
@ 121 °C
Rheometer at 150 °C
Scorch time, ts2, min 3.9 3. 0 2. 7
Optimum cure time, t90, min 10.7 8. 5 5. 1
Cure 150 °C /t90
M100, MPa 2.6 2. 9 3. 6
Tensile, MPa 24.9 23.6 25.1
Elongation, % 530 510 440
Formulation (in phr): NR, 80; BR, 20; N-375, 55; ZnO, 4; Stearic acid, 2; Aromatic oil,
8; N-(1,3-dimethylbutyl)-N´-phenyl-p-phenylenediamine (6PPD), 2
M100: Modulus at 100%
176
Figure 6.7 Structures of bis(sulphenamide) and pyrimidine sulphenamide
A thiocarbamyl sulphenamide, OTOS, derived from the hypothetical dialkyldithiocarbamic

acid provides processing safety comparable to the typical sulphenamides. In addition it
exhibits a high cure rate approaching that of an ultra accelerator [23]. The general structure
of thiocarbamyl sulphenamide is shown in Figure 6.8.
Figure 6.8 General structure of thiocarbamyl sulphenamide
6.2.2 Thiazoles
Thiazoles are by far the most commonly applied accelerators. The most important
accelerator of the group, MBT, was introduced in 1930 and its subsequent impact on the
rubber industry has been remarkable. Later came its disulphide, MBTS, and the zinc
salt, zinc-2-mercaptobenzothiazole (ZMBT). The zinc salt is rarely used in dry
compounding but is commonly used in the natural rubber latex industry, particularly in
the manufacture of elastic thread. The chemical structures of MBT, MBTS and ZMBT
are shown in Figure 6.9.
Figure 6.9 Chemical structures of MBT, MBTS and ZMBT
177
MBT provides a medium vulcanisation rate giving relatively low modulus vulcanisates, both in
NR and synthetic elastomers. It has a tendency, mainly in NR, to scorch during the processing
and storage of the green compound. Scorch safety can be increased by partial replacement of
MBT with its disulphide, MBTS. In natural rubber, MBT acts as a peptising agent at elevated
temperatures. It is common practice to use a secondary accelerator, a so-called booster or
kicker, in combination with MBT. With DPG, for example, a rapid vulcanisation rate with
considerable increase in modulus can be achieved. MBT can be boosted with thiuram disulphides
or dithiocarbamates to provide shorter cure times, but at the expense of scorch safety.
MBTS gives vulcanisates of relatively low modulus as does MBT. It does, however, provide
increased processing safety. It can be activated in a similar manner to MBT. ZMBT too gives
vulcanisates of low modulus, but it is used mainly in latex applications. In terms of its activity
and tendency to scorch it can be classified between MBT and MBTS.
6.2.3 Guanidines
The two main guanidine accelerators are DPG and di-o-tolyl guanidine (DOTG). Their chemical
structures are shown in Figure 6.10.
Figure 6.10 Chemical structures of DPG and DOTG
The guanidines are slow with regard to rate of vulcanisation but relatively safe accelerators in
terms of processing. They are rarely used as primary accelerators due to their slow cure rates,
although this can be put to good use in the cure of large sectioned articles. Their main use is as
a secondary accelerator in thiazole or sulphenamide accelerated NR or SBR compounds.
DPG is also used in speciality rubbers such as CR and polysulphide rubber where it acts as a
peptiser [24].
In silica containing compounds DPG is employed as a so-called cure activator. In reality its role
is to adsorb preferentially onto the acidic silica surface thereby preventing the deactivation of
the cure system. In addition, DPG facilitates the compatibilisation of the silica/elastomer
mix thus improving dispersion and processability.
178
6.2.4 Thiurams
The major members of this class are tetramethyl thiuram disulphide (TMTD), tetraethyl
thiuram disulphide (TETD) and tetramethyl thiuram monosulphide (TMTM), the former
being the most widely used. Their chemical structures are shown in Figure 6.11.
Figure 6.11 Chemical structures of TMTD, TETD and TMTM
They give a rapid rate of vulcanisation but are seldom used as primary accelerators. The
disulphides are able to function as sulphur donors, being used in curing systems containing
low or no elemental sulphur. The monosulphide, however, cannot function in this role
but does have the advantage of providing increased processing safety.
Thiuram accelerators have a broad range of applications from dipped latex goods,
vulcanised at low temperatures, to articles produced by press or injection moulding with
very short vulcanisation times. They are also applied in the manufacture of profiles by
continuous vulcanisation and in the manufacture of butyl rubber-based tyre tubes.
6.2.5 Dithiocarbamates
The metal and amine salts of dithiocarbamic acids provide a class of accelerators often
termed ultra accelerators due to the rapid cure rates that they impart. Popular members
of this class are zinc dimethyl dithiocarbamate (ZDMC) and zinc diethyl dithiocarbamate
(ZDEC), Figure 6.12. Salts of bismuth, cadmium, copper, lead, selenium and tellurium
are also available.
Figure 6.12 Chemical structures of ZDMC and ZDEC
179
Dithiocarbamates are considered as medium modulus accelerators but active at

temperatures even as low as 100 °C. As a result, they are often employed in the
manufacture of latex dipped goods. Another major application area is in the manufacture
of EPDM based profiles often in conjunction with thiazoles or sulphenamides.
Other dithiocarbamates that are commercially available are zinc dibutyl dithiocarbamate
(ZDBC), zinc ethyl phenyl dithiocarbamate (ZEPC) and piperidinium N-pentamethylene
dithiocarbamate (PPDC). Their chemical structures are shown in Figure 6.13.
Figure 6.13 Chemical structures of ZDBC, ZEPC and PPDC
ZDBC, ZEPC and PPDC are mainly used for vulcanisation of lattices and as non-staining
stabilisers of unvulcanised rubber solutions.
6.2.6 Dithiophosphates
Phosphorus-based compounds represent a second group of rapid curing accelerators,

the dithiophosphates. Their structure resembles that of dithiocarbamates, the most widely
used being zinc dibutyl dithiophosphate (ZBPD; Figure 6.14).
Figure 6.14 Chemical structure of ZBPD

They are used mainly as components of vulcanisation systems for EPDM. In combination
with thiazoles, good processing safety and a relatively fast cure rate can be achieved.
ZBPD can also be applied in the sulphur vulcanisation of diene elastomers. A partial replacement
of elemental sulphur in conventional vulcanisation systems improves resistance to ageing and
180
reversion whilst maintaining a good level of mechanical properties. Dithiophosphates are non-
staining and can be used at relatively high levels, up to 2 phr, with no detrimental effects from
blooming. They can be boosted with thiazoles, thiurams and dithiocarbamates.
6.2.7 Miscellaneous
In addition to the six classes described in Sections 6.2.1–6.2.6, there are further examples
which are discussed here.
Accelerators based on xanthate and thiourea structures are commercially available. The
former are mainly applied in latex applications to avoid copper staining whereas thioureas
are used as boosters in combination with MBT.
The most widely used materials are zinc isopropyl xanthate (ZIX) and ethylene thiourea
(ETU), Figure 6.15.
Figure 6.15 Chemical structures of ZIX and ETU
The use of thioureas is diminishing due to toxicological concerns.
6.2.8 N-Nitrosamines and accelerators
There is growing concern with regard to the presence of N-nitrosamines in rubber articles.
One source stems from the decomposition products of certain accelerators. The concern
centres on the suspected carcinogenic nature of these materials [25, 26].
Nitrosamines that are considered unsafe derive from accelerators containing secondary
amines. Currently the most commonly used accelerators that fall into this category are
listed in Figure 6.16.
181
Figure 6.16 Accelerators that give rise to suspected unsafe nitrosamines
Due to the suspected carcinogenicity of some nitrosamines, rubber chemical manufacturers

have been active in developing alternative accelerators that provide equivalent cure
characteristics whilst safe with regard to nitrosamine formation. The alternatives that
are gaining in commercial importance are TBSI, TBzTD and CLD.
TBSI, see Figure 6.6, provides an improvement in reversion resistance compared to the
corresponding sulphenamide and also possesses excellent storage stability; sulphenamides
182
are susceptible to hydrolysis, a significant problem in high temperature, high humidity

environments. TBSI is often employed as an alternative to MOR [27, 28], particularly in
steelcord skim stocks.
TBzTD, see Figure 6.2, is capable of producing nitrosamines, but nitrosamines that are
judged non-carcinogenic [29]. With minor compound changes it can replace TMTD.
TBzTD should be used at higher levels compared to TMTD to allow for its higher MW.
In addition, an increase in sulphur level is recommended [30].
CLD (see Figure 6.1), has been introduced as a potential replacement for DTDM. This
product does not generate nitrosamines.
Recently thiuram derivatives of diisobutyl amine, tetraisobutylthiuram disulphide (TiBTD)

and tetraisobutylthiuram monosulphide (TiBTM), have been introduced [31] as potential
substitutes for TMTD and TMTM, respectively, (see Figure 6.17). N-nitroso diisobutyl
amine, although considered carcinogenic, is reported to be safer than the nitrosamines
derived from TMTD and TMTM.
Figure 6.17 Chemical structures of TiBTD and TiBTM
6.3 Activators of vulcanisation
These are used both in sulphur as well as in peroxide vulcanisation. In the latter, they are
more commonly referred to as co-agents. The effect of activators is to increase the
crosslinking efficiency of the vulcanisation system.
Zinc oxide is the most commonly used activator in both sulphur and sulphur donor
vulcanisation. In addition to zinc oxide, magnesium oxide is often employed in the
vulcanisation of CR. Lead oxide is an effective activator for sulphur vulcanisation but it
is expensive and toxic, therefore seldom used.
183
As an activator of vulcanisation, zinc oxide requires the presence of fatty acids, thereby
converting the zinc into a rubber soluble form. Stearic acid is the most commonly used
fatty acid but can be replaced by lauric acid. The latter, being more soluble in elastomers,
provides more bloom resistance. Oleic acid is not recommended as it negatively affects
the ageing properties of the vulcanisate. Fatty acids also provide enhanced compound
processing characteristics together with improved dispersion of fillers and chemicals.
6.4 Retarders and inhibitors of vulcanisation
Vulcanisation retarders and inhibitors have been used in rubber compounds for many
years as a means of increasing processing safety. A vulcanisation retarder increases scorch
time, thereby improving processing safety, but also slows down the rate of vulcanisation.
This reduced rate of vulcanisation, however, is often an undesirable effect. True
vulcanisation inhibitors, on the other hand, increase scorch safety whilst having no adverse
effect on the rate of vulcanisation.
Substances that fall into the first category are acidic in nature, for example benzoic acid,
salicylic acid and phthalic anhydride. They prolong scorch time in thiazole accelerated
compounds but their effect in sulphenamide accelerated stocks is poor [32]. N-
chlorosuccinimide, nitroparaffins, sulphenic acid and sulphonic acid derivatives have
been described as retarders [33] but appear to have little practical significance.
N-nitrosodiphenylamine (NDPA) has a positive effect on the processing safety of

compounds accelerated with sulphenamides [34]. It prolongs the induction period with
regard to the onset of cure but does not reduce the rate of vulcanisation. As such it can
be classified as a vulcanisation inhibitor. However, it is no longer in use because of
toxicological concerns.
The major and most effective representative of the class of vulcanisation inhibitors is
N-(cyclohexylthio)phthalimide (CTP), (see Figure 6.18), often termed pre-vulcanisation
inhibitor (PVI). It is effective with a wide range of polymers, accelerators and other
compounding ingredients. It neither affects vulcanisate properties nor causes staining
or porosity. Although most effective in sulphenamide accelerated stocks, it is also used
with both MBT and MBTS. There is a linearity about its response that allows the
dosage necessary to give a certain scorch resistance to be readily determined. In most
applications 0.1–0.3 phr is used. The scorch resistance increases proportionally with
the dosage and an addition of 0.1 phr causes a considerable improvement (see Table
6.3). Furthermore the addition of PVI permits processing at elevated temperatures,
thereby increasing productivity.
184
MBS
!
processing safety is introduced.
Sulphur
PVI CTP
Mooney scorch,
t5, min @ 121 °C
0.65
1.75
-
42
Figure 6.18 Chemical structure of CTP
Although normally added during the mixing stage, PVI can also be added to compounds
during processing that are in danger of vulcanising prematurely. In doing so additional
PVI is not effective in thiuram accelerated stocks or resin and metal oxide curing systems.
In butyl-based compounds dosages should be adjusted upward from the range given,
perhaps up to 1 phr.
Additional products are commercially available but not as effective in terms of providing
scorch resistance. Examples are N-isopropylthio-N-cyclohexyl-2-benzothiazolyl
sulphonamide and N,N´,N´´–tri(thioizopropyl)-N,N´,N´´–triphenyl phosphorotriamide.
6.5 Antidegradants
Elastomer-based products suffer irreversible changes to their required design properties

during service. These changes, brought about by a number of agents such as oxygen,
Ingredients
Table 6.3 Effect of CTP on Mooney scorch time
1 2
0.1
60
Formulation
3
0.2
74
Formulation (in phr): NR, 75; BR, 25; N-220, 45; ZnO, 3; Stearic acid, 2
Mooney scorch time

4
0.4
99
185
ozone, heat, light and mechanical deformation, are collectively referred to as ageing. In
addition to a loss in mechanical properties, changes in surface aspect can occur that,
whilst perhaps not damaging with regard to performance, impair appearance. In order
to combat these detrimental changes additives, often collectively referred to as
antidegradants, are employed. Typical loading levels are of the order of 1–4 phr.
Antidegradants can be conveniently categorised into antioxidants and antiozonants.

However, this is not an unambiguous division since these materials often impart additional
benefits in addition to their primary function. A multitude of antidegradants are
commercially available and no attempt will be made here to describe the entire range but
only those of major importance. An abundance of literature exists to which the reader
can refer [35-41].
6.5.1 Antioxidants
Antioxidants are often further referred to as ‘staining’ and ‘non-staining’, designations

associated with the effect of these materials on the staining characteristics of the compound
to which they are added.
6.5.1.1 Phenolics
The most important group of non-staining antioxidants is based on phenol. Whilst not
as powerful as some staining antioxidants, phenolics are nevertheless an important class
of antidegradants due indeed to their non-staining and non-discolouring nature.
Appropriately they are applied in white and coloured vulcanisates. This group includes
monophenols, bisphenols, thiobisphenols, polyphenols and hydroquinone derivatives.
2,6-di-t-butyl-p-cresol, frequently referred to as BHT (see Figure 6.19), is the most widely
used phenolic antioxidant. It is also representative of the basic, generic building block of
all phenolic antioxidants.
Figure 6.19 Structure of BHT
186
In Figure 6.20, additional examples based on the monophenolic BHT structure

are shown.
The higher MW bisphenolic antioxidants, see Figure 6.21, offer reduced volatility and
increased activity but at a price premium compared to the monophenolics.
Polyphenolic antioxidants offer still further resistance to volatility during processing

and service; an example is shown in Figure 6.22.
Figure 6.20 Some examples of monophenolic antioxidants
Figure 6.21 Examples of bisphenolic antioxidants
Figure 6.22 A polyphenolic antioxidant
187
Hydroquinone derivatives based on the structure shown in Figure 6.23 also offer non-
staining performance. An additional major use is in the polymer manufacturing industry
as a MW modifier [42].
Figure 6.23 Hydroquinone derivatives

6.5.1.2 Phosphites
Phosphites are the second major class of non-staining antioxidants. The most commonly
used material of this class is tris(nonylphenyl)phosphite, (TNP; see Figure 6.24). However,
it suffers from a tendency to hydrolyse during prolonged contact with moisture and it is
destroyed during vulcanisation. Nevertheless, its exceptional non-tinting property has
made it the industry’s standard non-staining SBR stabiliser. TNP is ideally suited to the
emulsion polymerisation process because of its liquid physical form.
Figure 6.24 Tris(nonylphenyl)phosphite
6.5.1.3 Thioesters
A third category of antioxidants comprises thioesters with essentially two classes of

materials: the bis-(alkylthiopropionate)diesters (BTPDE) and the alkylthiodipropionate
esters (TDPE). Typical structures are shown in Figure 6.25.
As for phosphite-based antioxidants, they are destroyed during vulcanisation and thus
find little use in the rubber industry. They are used primarily for the stabilisation of
polyolefins.
188
Figure 6.25 Chemical structures of BTPDE and TDPE
6.5.1.4 Amines
Historically, amine-based antioxidants were the first really effective rubber antioxidants.
The materials can be categorised as: naphthylamines, diphenyl amine derivatives,
dihydroquinolines and paraphenylenediamines (see also Section 6.5.2).
The naphthylamines, phenyl-#-naphthylamine (PBNA) and its companion phenyl-"-

naphthylamine (PANA), whilst extremely effective antioxidants have now almost
disappeared due to toxicological concerns [43].
Structures of the four types are shown in Figure 6.26.
Figure 6.26 Amine-based antioxidants: a) Phenyl-"-naphthylamine b) diphenyl amine

c) p-phenylenediamine and d) dihydroquinoline
6.5.1.5 Bound antioxidants
In 1972, The Malaysian Rubber Producers Research Association reported that

quinonediimines could provide bound antioxidant activity [44], the antioxidant becoming
189
attached to the elastomer during vulcanisation. This prevents the antidegradant from
being extracted during service of the rubber article thereby providing long term protection.
At the time the materials were not commercialised but recently one such product has
been introduced, N-1,3-dimethyl butyl-N´-phenyl-p-quinone diimine (QDI), Figure 6.27.
In addition to providing long term antioxidant protection it can also serve as a peptiser,
a vulcanisation retarder and can enhance polymer-filler interaction [45].
Figure 6.27 Structure of N-1,3-dimethyl butyl-N´-phenyl-p-quinone diimine (QDI)
6.5.1.6 Miscellaneous
In addition to the several classes described above there are other materials that can act as
antioxidants. The zinc and nickel salts of the dithiocarbamates are two such materials.
They are sometimes applied [46] in CR, chlorosulphonated-polyethylene (CSM),
polyepichlorohydrin (CO), the copolymer of epichlorohydrin and ethylene oxide (ECO)
and EPDM based compounds. The zinc salt of MBT is also reported to act as an
antioxidant in latex applications.
2-Mercaptobenzimidazole (MBI) and its zinc salt are efficient antioxidants for both natural
and synthetic rubbers, providing protection against oxidation, high temperatures and
surface crazing. It does not protect against fatigue and ozone. The structure of MBI is
shown in Figure 6.28.
Figure 6.28 Structure of MBI
6.5.2 Antiozonants
Under deformation vulcanisates that are susceptible to ozone attack have a critical
elongation below which cracks will not form. This varies with the type of rubber and
190
compounding ingredients, but it is usually in the range of 5–10% for diene rubbers.
Above this critical elongation cracks do appear, becoming progressively more numerous
as a function of time. The incorporation of antiozonants in the compound, however,
provides a marked improvement in the resistance to ozone attack. They function by
migrating from the bulk of the vulcanisate to the surface where they react preferentially
with the ozone thereby safeguarding the integrity of the component.
The most widely used antiozonants are the substituted para-phenylenediamines. They
not only offer protection against ozone but also function as antioxidants and as
outstanding antiflex agents. Nickel dithiocarbamates are also active as antiozonants but
they are of minor importance in terms of usage [47].
6.5.2.1 Para-phenylenediamines
Para-phenylenediamines, the most widely used class of antidegradant, provide protection

against oxygen, ozone, metal ions and flex fatigue. One major drawback, however, is
that they are discolouring and staining. They can be conveniently grouped into three
categories based on the chemical nature of substituents (see Figure 6.29): diaryl-p-
phenylenediamines, dialkyl-p-pheylenediamines and alkyl-aryl-p-phenylenediamines.
Figure 6.29 General structure of para-phenylenediamines
a) Diaryl-p-phenylenediamines
The diaryl-p-phenylenediamines are the least reactive of the p-phenylene diamines towards
ozone but they possess relatively low volatility and provide long protection. Due to their
basicity they have an activating effect on sulphur cure systems. The most widely used
diaryl derivative is the diphenyl, Figure 6.30.
Figure 6.30 N, N´-diphenyl-p-phenylenediamine
191
b) Dialkyl-p-phenylenediamines
The most common member of this group incorporates branched C7 substituents (see
Figure 6.31). The dialkyls provide superior ozone resistance but do not offer the same degree
of protection against oxygen as other p-phenylenediamines. They are more volatile than the
diaryls and hence do not provide such long-term protection. As for other p-phenylenediamines
they also provide flex crack resistance and protect against metal ion catalysed degradation.
Figure 6.31 N,N´–bis-1,4-dimethyl pentyl-p-phenylene diamine (77PD)
c) Alkyl-Aryl-p-phenylenediamines
The alkyl-aryl-p-phenylenediamines offer the best all round antidegradant protection.

They are not as reactive as the dialkyls but are not as volatile, thus provide longer
protection. The most widely used antiozanant in this group is the product bearing a
phenyl and a branched C6 alkyl group, 6PPD, Figure 6.32. The isopropyl analogue,
IPPD, is also commonly used but is gradually being replaced by 6PPD; IPPD is more
readily leached from vulcanisates during service.
Figure 6.32 Chemical structures of 6PPD and IPPD
6.5.2.2 Triazine derivative
(N-1,4-dimethylpentyl-p-phenylenediamino)-1,3,5-triazine, although an active

antiozonant is not used extensively in the rubber industry due to its limited solubility in
synthetic rubbers and its high cost. It functions also as an antioxidant and is non-staining.
The structure is shown in Figure 6.33.
192
Figure 6.33 Chemical structure of (N-1,4-dimethylpentyl-p-phenylenediamino)-1,3,5-

triazine
6.5.2.3 Waxes
Waxes provide protection from ozone by blooming to the surface of the rubber component.
However, unlike the p-phenylenediamines they offer only physical protection. This is a
result of the formation of a thin film of wax at the surface acting as a barrier toward
ozone attack of the elastomer. If, however, the film is ruptured, for example on flexing of
the component, the ozone resistance is lost. Waxes therefore are effective with regard to
static ozone protection only and do not provide protection under dynamic conditions.
The migration rate of the wax is important in providing optimum static ozone protection.
Often a blend of paraffin and microcrystalline waxes are used in order to provide
protection over a wide range of temperature.
6.6 Antireversion agents
Reversion of sulphur-based crosslinks and the consequent loss in vulcanisate properties

presents a major challenge to the rubber compounder. A number of additives are available
that, in one way or another, provide some protection against reversion.
6.6.1 Zinc carboxylates
A blend of aliphatic and aromatic zinc carboxylic acid salts is commercially available
that provides reversion resistance by promoting the formation of sulphidic crosslinks of
lower sulphur rank. The general structure of the material is shown in Figure 6.34. Its
mechanism of action is due to increased solubility in the rubber matrix compared to the
zinc salt of stearic acid [48]. The latter is normally generated in situ as a result of the
reaction between zinc oxide and stearic acid.
193
Figure 6.34 Zinc carboxylate
The data shown in Table 6.4 clearly demonstrate the effect of the material on crosslink
network structure [49].
6.6.2 Thiophosphoryl derivatives
Thiophosphoryl derivatives such as ZBPD (see Figure 6.35) provide improvement in

reversion resistance when added to a sulphenamide cure system [50]. Again, reversion
resistance is a result of the formation of a crosslink network containing a higher proportion
of monosulphidic crosslinks. Data listed in Table 6.5 demonstrate the effect for a ZBPD
based compound [49].
Figure 6.35 Chemical structures of thiophosphoryl derivatives
Table 6.4 Effect of zinc carboxylate on network structure

Compounds A B
Stearic acid, phr 2 0
Zinc soap, phr 0 2
Cure temperature, °C 150 150
Cure time, min 13 13
Crosslink density 5.10 5.24
% Polysulphide 50 40
% Disulphide 15 12
% Monosulphide 35 48
Crosslink density expressed in g mol/g rubber hydrocarbon x 105
Formulation (in phr): NR, 100; N-375, 45; Zinc oxide, 5; Peptiser, 0.3; Microcrystalline
wax, 1.4; CTP, 0.5; 2,2,4-trimethyl-1,2-dihydroquinoline, polymerised (TMQ), 1.5;
6PPD, 1.2, TBBS, 1.4 and Sulphur,1.4
194
Table 6.5 Effect of ZBPD on network structure

Compounds C D
TBBS, phr 0.6 0.2
Sulphur, phr 2.5 2.5
ZBPD, phr - 0.75
% Disulphide 10 17
Crosslink density expressed in gmole/g rubber hydrocarbon x 105
Formulation (in phr): NR, 100; N-330, 50; Naphthenic oil, 5; Zinc oxide, 5; Stearic acid,
2; 6PPD, 2.0
6.6.3 Silane coupling agents
Silane coupling agents possess multifunctional activity. Their major role is, as the name
implies, as a coupling agent between silica filler and elastomer. This action provides
significant improvements in the physical properties of vulcanisates [51]. The most widely
used material, bis-(3-triethoxysilylpropyl)-tetrasulphide TESPT is shown in Figure 6.36.
It also functions, however, as a sulphur donor, providing an ‘equilibrium cure system’
[52]. Its mechanism of action is associated also with the formation of crosslinks of lower
sulphur rank.
Figure 6.36 Chemical structure of TESPT
The effect of TESPT on the network structure of a NR based compound is shown in

Table 6.6 [49].
6.6.4 Sulphenimide accelerator
A commercially available sulphenimide accelerator, TBSI (see Figure 6.6), provides a

long scorch delay together with a slow cure rate [53]. Its effect on network structure is
195
Table 6.6 Effect of TESPT on network structure

Stocks E F
TESPT, phr 0 3
Cure time, min 6 11
% Disulphide 15 12
Crosslink density expressed in g mole/g rubber hydrocarbon x 105
Formulation (in phr): NR, 100; N-220, 40; Silica, 20; Zinc oxide, 5; Stearic acid, 2;
aromatic oil, 3; Resin Coumaron, 3; MC wax, 1.0; TMQ, 1.5; 6PPD, 2.5; CBS, 1.4;
DPG, 2; Sulphur, 1.4
once again to shift the distribution of crosslink type towards lower sulphur rank thus
enhancing reversion resistance.
Its effect on network structure of a NR based compound is shown in Table 6.7 [49].
6.6.5 Hexamethylene-1,6-bis thiosulphate disodium dihydrate (Duralink HTS)
Duralink HTS (see Figure 6.37), is a material that functions during vulcanisation by
forming hybrid crosslinks composed of hexamethylene and sulphidic moieties [54, 55].
Table 6.7 Effect of TBSI on network structure

Compounds G H
TBBS, phr 0.6 0
TBSI, phr 0 0.6
Sulphur, phr 2.5 2.5
Cure temperature °C 150 150
% Disulphide 16 12
Formulation (in phr): NR, 100; N-339, 55; Zinc oxide, 5; Stearic acid, 2; Aromatic oil, 3;
MC Wax, 1; 6PPD, 2; TMQ, 1.0
196
Figure 6.37 Structure of hexamethylene-1,6-bis thiosulphate disodium dihydrate
The presence of these hybrid crosslinks increases the reversion resistance of the network
and is particularly beneficial in maintaining flex/fatigue resistance.
6.6.6 1,3-Bis(citraconimidomethyl)benzene (BCI-MX; Perkalink 900)
The most recently introduced antirevesion agent, 1,3-bis(citraconimidomethyl)benzene

(Perkalink 900; Figure 6.38), functions by a crosslink compensation mechanism [56-62].
It compensates for the loss of polysulphidic crosslinks during the process of reversion with
crosslinks based essentially on a carbon-carbon structure. The material reacts at the onset
of reversion and can be added to existing compounds with no further change in formulation.
Its effect on the network structure of a NR based compound is shown in Table 6.8.
Figure 6.38 Structure of BCI-MX
Table 6.8 Effect of 1,3-bis(citraconimidomethyl)benzene on network

structure
Compounds I J
BCI-MX, phr 0 1
Cure time, min, at 150 °C t90 60 t90 60
Crosslink density 4.95 3.56 5 . 11 4.99
Polysulphide 3.96 2 . 16 4.04 2.29
Disulphide 0.84 0.36 0.90 0.42
Monosulphide 0.15 1.06 0.17 1.06
Carbon-Carbon 0.00 0.00 0.00 1.22
Formulation (in phr): NR, 100; N-330, 50; Zinc oxide, 5; Stearic acid, 2.0; Aromatic oil,
3; CBS, 0.6; Sulphur, 2.3
197
6.7 Plasticisers and softeners
Plasticisers and softeners are relatively non-volatile organic materials that when added to
compounds will improve their workability during processing, modify green and cured
compound properties and reduce cost. They are materials coming from a number of sources
and may be conveniently classified according to their origin. The main groups discussed in
Section 6.7.1 are petroleum products, coal tar products, pine products, synthetic softeners,
and other products.
6.7.1 Petroleum products
6.7.1.1 Petroleum waxes
About 90% of all waxes used for commercial purposes are recovered from petroleum.
Petroleum waxes are generally classified into three principle types: paraffinic, microcrystalline
and petrolatum. Paraffin wax is a solid, colourless substance composed of alkanes up to 30
carbon atoms in length with a low level of branching. As a consequence of the regular structure,
paraffin wax crystallises relatively easily into large plates or needles.
Microcrystalline paraffin wax differs from paraffin wax in having a higher MW and, therefore,
a higher softening temperature. The molecular structure is more branched resulting in a
microcrystalline material.
Petrolactum is a semi-solid substance, substantially a mixture of a high MW hydrocarbon,

ceresine and oils.
6.7.1.2 Mineral oils
Mineral oils are the most frequently used plasticisers for both natural and synthetic rubbers.
They are high boiling fractions obtained in refining crude oil.
The oils are comprised mainly of ring structures: unsaturated (aromatics), saturated
(naphthenes) and ring structures possessing saturated side chains (paraffins). They are classified
accordingly as aromatic, naphthenic and paraffinic depending on the predominant structure
of the oil.
The choice of oil depends largely on the compatibility with the elastomer. As a general rule
paraffinic oils are best used with low polarity polymers whilst aromatics are more suited to the
more polar polymers. Table 6.9 lists oil suitability with the more common elastomers [63].
198
Table 6.9 Oil suitability

Polymer Paraffinic Naphthenic Aromatic
Natural rubber Excellent Fair Fair
SBR Fair Good Excellent
Butyl Excellent Good Poor
Polybutadiene Fair Good Excellent
Neoprene Poor Good Excellent
Nitrile Poor Fair Excellent
EPDM Excellent Good Good
6.7.2 Coal tar products
Softeners belonging to this group are products of various consistency: oils, soft and hard
resins and pitches. From the chemical point of view they comprise a rich mixture of
components: non-aromatic, aromatic and polar hydrocarbons including sulphur, nitrogen
and oxygen containing compounds.
6.7.2.1 Coumarone resin
The fraction of coal tar distilling in the 160–200 °C range contains, after elimination of
phenol, cresol and pyridine, mainly coumarone and indene. Under the effect of 2–5%
sulphuric acid, polymerisation takes place producing a copolymer referred to as coumarone
resin. According to the degree of polymerisation a variety of products can be obtained,
from viscous liquids to hard brittle resins with softening point of 100 °C and higher.
Their colour depends on the degree of preliminary refinement of the coumarone-indene
fraction, varying from colourless to dark brown. Both solid and liquid resins are used in
the rubber industry.
6.7.3 Pine products
Colophony (rosin) is present in the resin flowing from cut pine trees (primarily Pinus
palustris). It is added to rubber compounds to impart tack, soften the compound and to
improve flow. Pine rosin is a solid, yellow-dark brown resin with softening point around
70 °C. It is acidic in nature due to its main component, abietic acid, and its isomer,
pimaric acid. As a result of its acidic character it retards vulcanisation. In addition to its
softening action it aids in the dispersion of carbon black and provides some age resistance
to compounds.
199
6.7.4 Synthetic softeners
There is a broad variety of ester plasticisers possessing widely different properties. The
group comprises esters of polycarboxylic acids such as adipic, phosphoric, phthalic, sebacic
and higher aliphatic alcohols or phenols such as butanol, cresols, cyclohexanol and
octanol. Dibutyl phthalate, di-2-ethylhexyl phthalate, di-2-ethylhexyl sebacate and
tricresyl phosphate are commonly used. Esters are relatively high priced and are used to
provide low temperature flexibility to the more polar rubbers such as chloroprene, nitrile
and acrylate elastomers.
Ether type plasticisers include dibenzyl ether, polyethers and polyether-thioethers.
6.7.5 Other products
Vegetable oils and fats are occasionally used in rubber compounding. These include
unsaturated oils such as linseed, rapeseed and sunflower oils. They are mostly used in
chloroprene to obtain low temperature flexibility, tear resistance and antiozonant
protection. The use of these plasticisers, however, should be avoided in hot and humid
areas of the world due to their tendency to promote fungal growth. Allied to the vegetable
oils are the vulcanised vegetable oils such as factice. If the oil is vulcanised with sulphur,
the product is dark and is termed ‘brown factice’. If sulphur monochloride is used as the
vulcanisation agent the product is light coloured and is referred to as ‘white factice’. The
addition of 5 to 20 phr of factice to a compound improves processibility.
Fatty acid derivatives such as stearic, palmitic, oleic or linoleic acid act as effective
processing agents. In this respect the most commonly used processing additive is stearic
acid, used primarily however for cure activation. Technical grade stearic acid is a mixture
of approximately equal amounts of stearic acid (C18) and palmitic acid (C16) together
with a small amount of oleic acid (unsaturated C18).
Zinc salts of unsaturated fatty acids are also available and are commonly used to
improve compound processability and as compatibilising agents for compounds based
on polymer blends.
6.8 Miscellaneous ingredients
A number of additional compounding materials, although not as widely used as those

mentioned previously, warrant a brief review. These include: peptising agents, blowing
agents, bonding agents and pigments.
200
6.8.1 Peptising agents
Peptising agents are substances that act as chain terminating agents during the mastication
of rubber. They may also act as pro-oxidants during the mastication process. This
significantly reduces the time necessary to lower the viscosity of the rubber to a workable
level, which in turn brings savings in mixing time and energy.
Although numerous materials are known to possess chemical peptising activity, in practice
the choice is limited due to additional considerations such as health and safety, effect on
vulcanisation characteristics and price. Consequently only a limited number of substances
are commercially available. These are indicated in Figure 6.39.
Recently a multifunctional additive has been introduced which possesses chemical

peptising activity in NR-based compounds. In addition it acts both as an antiozanant
and a bound antidegradant following reaction during mixing and vulcanisation [64].
The material is a quinonediimine, N-1,3-dimethyl butyl-N´-phenyl-p-quinonediimine,
and is described in Section 6.5.1.5.
Figure 6.39 Commercially available peptising agents
201
6.8.2 Blowing agents
Blowing agents are used in the manufacture of sponge rubber. Sodium bicarbonate, the
first commercially used blowing agent, reacts with stearic acid to produce carbon dioxide
at vulcanisation temperatures. A disadvantage of using sodium bicarbonate is that residual
soap is left in the final product.
The commonly used blowing agents now rely on the formation of nitrogen as the effective
expansion agent resulting from thermal decomposition at vulcanising temperatures.
Blowing agents of this class are: p-toluenesulphonylsemicarbizide, azodicarbonamide,
diazoaminobenzene, N,N´-dinitrosopentamethylenetetramine and p-p´-oxy
bis(benzenesulphonylhydrazide).
Although the latter has been marketed widely, it has the disadvantage of having low
decomposition temperatures and an unpleasant fish odour.
6.8.3 Bonding agents
Most large volume rubber products are bonded composites: tyres, hoses and belts, for
example. During their manufacture bonding agents added to the compound may be
required in order to increase the bond strength between the different components. A
complicating feature of composite bonding is the variety of metals and fabrics to which
the rubber compound must be bonded. The metals, usually plated with zinc, brass or
aluminium, are used in the form of metal plate or wire. Textiles used in the manufacture
of composites include cotton, nylon, polyester, rayon, aramid and glass.
The integrity of steelcord rubber composites is of great concern in the radial tyre
manufacturing industry. Often, in order to ensure increased adhesion retention, bonding
agents are employed as adjuncts to the compound formulation. Bonding agents commonly
employed are cobalt-based salts such as naphthenate or stearate. Proprietary materials
are also available based on cobalt and boron complexes.
For adhesion of rubber compounds to synthetic fibres such as polyester or nylon it is

common practice not only to treat the surface of the fibre with a two component resin
system, such as resorcinol together with a methylene donor, but also to include such a
system in the compound itself. Resorcinol together with hexamethylenetetramine or
hexamethoxymethylmelamine is commonly employed.
202
6.8.4 Pigments
Although most rubber compounds are black, coloured rubber compounds are frequently
required to add appeal to consumer items such as sports shoes, household gloves,
rubber toys, bathing caps, etc., (see also Chapter 13). In addition colour coding is
often a necessity in products such as hoses and cables. Clearly pigments are required to
impart the desired colour.
Pigments can be classified as inorganic or organic. Comparing the two, inorganic

pigments are often dull and in some cases too opaque to impart the desired richness
of shade. They are insoluble and thus cannot bloom. Organic pigments generally
give brighter shades but are more sensitive to heat and other chemicals. On long-
term exposure to sunlight they can fade badly. Above all they are relatively expensive.
Some commonly used inorganic and organic pigments are shown in Table 6.10.
Table 6.10 Commonly used pigments

Colour Organic/Inorganic Pigment
Green Inorganic Chromium oxide
Blue Inorganic Cobalt blue, ultramarine (iron blue)
Brown Inorganic Iron oxides
Yellow Inorganic Cadmium sulphide, lead chromate, iron oxide
Red Inorganic Iron oxide, cadmium sulphide selenide
Red Organic Red pyrazoline
Yellow Organic Diarylide
Orange Organic Diasnisidine
Blue/Green Organic Phthalocyanine
6.9 Concluding remarks
Rubber additives play an important role in achieving the performance requirements

of rubber articles. Furthermore, these performance requirements are becoming more
and more demanding due to the ever-increasing severity of service conditions, health
and safety concerns and quality expectations.
203
Today, more and more additives are available to the rubber compounder allowing
him to meet these requirements. Whilst many of these rubber additives have been
commercially available for years, others have become available relatively recently.
Antireversion agents constitute a class of such materials, once again emphasizing the
need to meet more demanding service conditions. Health and safety issues, as for
example that concerning the generation of N-nitrosamines, have also lead to the
introduction of new rubber additives.
Rubber additives, however, paint only part of the picture with regard to the manufacture
of rubber articles; polymers and fillers are equally important in meeting performance
requirements. In addition, compound mixing and processing play a vital role in achieving
final vulcanisate properties. These are the subject of other chapters in this publication.
Acknowledgements
The authors wish to thank the many contributors of the information contained within
this chapter. Special thanks are due to Dr. A. G. Talma and Dr. J. P. Baaij for their
assistance and valuable suggestions in preparation of the manuscript.
References
1. H. Bartzsch, Indian Rubber Journal, 1994, 6, 67.
2. F. A. A. Ingham and B. To, Presented at Tyre Tech Asia 96, Singapore, 1996,
Paper No.20.
3. D. Seeberger, J. Baaij and R. Datta, Unpublished results.
4. Kirk-Othmer Encyclopaedia of Chemical Technology, 4th Edition, Volume 20,

Eds., J. I. Kroschwitz and M. Howe-Grant, John Wiley & Sons, Inc., New York,
1996, 337.
5. S. Wolff, Kautschuk und Gummi Kunststoffe, 1979, 32, 10, 760.
6. L. H. Davies, A. B. Sullivan and A. Y. Coran, Rubber Chemistry and Technology,

1987, 60, 1, 125.
7. I. I. Ostromysklenki, Russian Physical-Chemical Society Journal, 1915, 47, 1467.
8. G. Natta, G. Crespi, E. Digiulio, G. Ballini and M. Bruzzone, Rubber Plastics

Age, 1961, 42, 53.
204
9. R. D. Allen, Gummi Asbestos Kunststoffe, 1983, 36, 10, 534.
10. R. C. Keller, Rubber Chemistry and Technology, 1988, 61, 2, 238.
11. W. C. Endstra and C. T. J. Wreesmann in Elastomer Technology Handbook, Eds.,

N. P. Cheremisinoff and P. N. Cheremisnoff, CRC Press, NJ, USA, 1993, Chapter
12.
12. C. S. L. Baker, D. Barnard and M. Porter, Rubber Chemistry and Technology,

1970, 43, 3, 501.
13. C. S. L. Baker, D. Bernard and M. Porter, Journal of the Rubber Research

Institute Malaya, 1969, 22, 317.
14. C. S. L. Baker, Presented at the Rubber Manufacturing Technology Seminar, PRI,

Kuala Lumpur, Malaysia, 1981.
15. K. C. Baranwal and W. L. Seman, Rubber Chemistry and Technology, 1983, 56,
2, 945.
16. F. W. Barlow, Rubber Compounding: Principles, Materials and Techniques, 2nd

Edition, Marcel Dekker, Inc., New York, 1993, Chapter 8.
17. I. Franta, P. Vondracek, B. Meissner and V. Duchacek, Elastomer and Rubber

Compounding Materials, Elsevier, Amsterdam, 1988, Chapter 6.
18. M. L. Weiss, inventor; Dovan Chemicals, assignee; US Patent 1411231, 1921.
19. G. Bruni and E. Romani, Indian Rubber World, 1922, 67, 20.
20. W. Hofmann, S. Koch, Kautschuk-Handbuch, Ed., Bayer AG, Berliner Union-

Kohhammer, Stuttgart, 1971.
21. R. N. Datta and J. Baaij, Unpublished results.
22. C. J. Rostek, H-J. Lin, D. J. Sikora, A. R. Katritzky, W. Kuzmierkiewicz and N.

Shobana, Rubber Chemistry and Technology, 1996, 69, 2, 180.
23. R. W. Layer, Presented at the 128th ACS Rubber Division Meeting, Cleveland,
OH, Fall 1985, Paper No.112.
24. W. Hofmann, Vulcanizing and Vulcanizing Chemicals, MacLaren, London-

Palmerton, New York, 1967.
205
25. D. Seeberger and G. Raabe, Kautschuk und Gummi Kunststoffe, 1989, 42, 1, 27.
26. G. Raabe, D. Seeberger and P. Bolte, Kautschuk und Gummi Kunststoffe, 1988,
41, 11, 1067.
27. D. G. Lloyd and A. Gergely, Rubber World, 1994, 210, 5, 25.
28. D. A. Lederer and M. Zaper, Presented at the 140th ACS Rubber Division
Meeting, Detroit, MI, Fall 1991, Paper No.59.
29. D. Seeberger, Rubber World, 1990, 202, 5, 18.
30. T. L. Jablonowski, Rubber World, 1992, 206, 5, 18
31. R. W. Layer and D. W. Chasar, Rubber Chemistry and Technology, 1994, 67, 2,
299.
32. A. W. Campbell, Industrial and Engineering Chemistry, 1941, 33, 809.
33. No inventor; Naugatuck, assignee; US Patent 1871037, 1930.
34. C. D. Trivette, Jr., E. Morita and O. W. Maender, Rubber Chemistry and

Technology, 1977, 50, 3, 570.
35. Th. Kempermann, Kautschuk-Handbuch, Verlag Berliner Union, Stuttgart, 1961,

4, 353.
36. Developments in Polymer Stabilisation - 7, Ed., G. Scott, Elsevier Applied Science

Publishers Ltd., London, 1984.
37. R. W. Keller, Rubber Chemistry and Technology, 1985, 58, 3, 637.
38. G. P. Langner, T. Kempermann and O. Rosenthal, Kautschuk und Gummi

Kunststoffe, 1979, 32, 2, 81.
39. R. P. Lattimer, E. R. Hooser, H. E. Diem, R. W. Layer and C. K. Rhee, Rubber

Chemistry and Technology, 1980, 53, 5, 1170.
40. D. A. Lederer and M. A. Fath, Rubber Chemistry and Technology, 1981, 54, 2,
415.
41. R. P. Lattimer, R. W. Layer and C.K. Rhee, Rubber Chemistry and Technology,
1984, 57, 5, 1023.
206
42. J. C. Ambeling, R. H. Kline, O. M. Lorenz, C. R. Parks, C. Wadelin and J. R.

Shelton, Rubber Chemistry and Technology, 1963, 36, 1497.
43. B. T. Ashworth and P. Hill, Developments in Rubber Technology – 1, Applied

Science Publishers, London, 1979.
44. M. E. Cain, I. R. Gelling, G. T. Knight and P. M. Lewis, Rubber Industry, 1975,

9, 6, 216.
45. F. Ignatz-Hoover, O. Maender and R. N. Datta, Presented at the 152nd ACS

Rubber Division Meeting, Cleveland, OH, Fall 1997, Paper No.107.
46. A. D. T. Gorton, NR Technology, 1989, 20, 4, 65.
47. R. W. Layer and R. P. Lattimer, Rubber Chemistry and Technology, 1990, 63, 3,
426.
48. J. Vander Kooi and J. Sherritt, Presented at the 144th ACS Rubber Division
Meeting, Orlando, FL, Fall 1993, Paper No.121.
49. R. N. Datta, A. G. Talma, B. J. Oude Egbrink and F. A. A. Ingham, Gummi

Fasern Kunststoffe, 2001, 54, 179.
50. A. Johanssen and T. Fruel, Presented at the 152nd ACS Rubber Division Meeting,
Cleveland, OH, Fall 1997, Paper No.106.
51. S. Wolff, Rubber Chemistry and Technology, 1982, 55, 4, 967.
52. S. Wolff, Kautschuk und Gummi Kunststoffe, 1979, 32, 10, 760.
53. D. A. Lederer and M. Zaper, Rubber World, 1992, 206, 1, 25.
54. W. F. Helt and B. H. To, Rubber World, 1991, 204, 5, 18.
55. A. Fitch, D. G. Lloyd and A. Orband, Kautschuk und Gummi Kunststoffe, 1989,
42, 10, 880.
56. R. N. Datta, J. H. Wilbrink and F. A. A. Ingham, Indian Rubber Journal, 1994,

8, 52.
57. R. N. Datta and M. S. Ivany, Rubber World, 1995, 212, 5, 24.
58. R. N. Datta and W. F. Helt, Rubber World, 1997, 216, 5, 24.
207
59. R. N. Datta and J. C. Wagenmakers, Kautschuk und Gummi Kunststoffe, 1996,

49, 10, 671.
60. A. H. M. Schotman, P.J. C. van Haeren, A. J. M. Weber, F. G. H. van Wijk, J. W.

Hofstraat, A. G. Talma, A. Steenbergen and R. N. Datta, Rubber Chemistry and
Technology, 1996, 69, 5, 727.
61. R. N. Datta, A. H. M. Schotman, A. J. M. Weber, F. G. H. Van Wijk, P. J. C. van

Haeren, J. W. Hofstraat, A. G. Talma and A. G. v.d. Bovenkamp-Bouwman,
Rubber Chemistry and Technology, 1997, 70, 1, 129.
62. R. N. Datta, A. G. Talma and A. H. M. Schotman, Rubber Chemistry and

Technology, 1998, 71, 5, 1073.
63. M. L. Studebaker and J. R. Bettey in Science and Technology of Rubber, Ed., F.

R. Eirich, Academic Press, Inc., London, Chapter 9.
64. F. Ignatz-Hoover and R. Datta, Presented at the 156th ACS Rubber Division
Meeting, Orlando, FL, Fall 1999, Paper No.31.
208

Rubber Additives - Compounding Ingredients: R. N. Datta and F. A. A. Ingham

Uploaded by

Copyright:

Available Formats

Rubber Additives - Compounding Ingredients: R. N. Datta and F. A. A. Ingham

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Rubber Additives - Compounding Ingredients: R. N. Datta and F. A. A. Ingham

Uploaded by

Copyright:

Available Formats

What are vulcanising agents?

What are vulcanising agents?

What are some common vulcanising agents mentioned?

What are some common vulcanising agents mentioned?

6

Rubber Additives - Compounding Ingredients

R. N. Datta and F. A. A. Ingham

6.1 Vulcanising agents

• elimination of sulphur bloom,

• prevention of sulphur migration between green components during storage,

• reduced bin-scorch during the storage of green compounds.

6.1.2 Sulphur donors

Figure 6.1 Structures of sulphur donors

Figure 6.2 Structure of TBzTD

Figure 6.3 Structures of peroxides

There are a number of advantages, associated with the peroxide vulcanisation of

• scorch free storage of compounds,

• possibility to apply high vulcanisation temperatures without reversion,

• simple compound formulation,

• low compression set even at high cure temperatures,

• good electrical properties of vulcanisates,

• good high temperature vulcanisate stability,

There are, however, some drawbacks compared to sulphur vulcanisation:

• limited compounding flexibility due to the reaction of peroxides with other

• sensitivity of vulcanisation reactions to oxygen,

Table 6.1 Typical crosslinking temperatures of crosslinking peroxides based

2,5-Bis(tert-butylperoxy) 159 180

Tert-butylcumyl peroxide 160 180

Peroxy ketals Butyl 4,4-bis (tert-butyl 143 160

1,1-Bis(tert-butyl peroxy) 129 150

• lack of flexibility in regulating scorch and optimum cure time,

• inferior tensile, tear and flex properties,

• inferior abrasion resistance,

• frequently disturbing odours of peroxide decomposition products,

• generally higher cost.

6.1.4 Urethane crosslinking

urethane compounds, Novor 924 being an adduct of a substituted nitrosophenol and

6.1.5 Metal oxides

6.1.6 Other vulcanising agents

Diamines with blocked amino groups, e.g., hexamethylene diaminocarbamate, ethylene

6.2 Vulcanisation accelerators

Figure 6.5 Cure characteristics at 150 °C

Figure 6.6 Structures of TBBS and TBSI

Sulphenamides can be activated by the addition of a secondary accelerator, for example

Although as yet unavailable commercially, excellent processing safety combined with a

Table 6.2 Effect of secondary accelerators on the vulcanisation

Figure 6.7 Structures of bis(sulphenamide) and pyrimidine sulphenamide

A thiocarbamyl sulphenamide, OTOS, derived from the hypothetical dialkyldithiocarbamic

Figure 6.8 General structure of thiocarbamyl sulphenamide

Figure 6.9 Chemical structures of MBT, MBTS and ZMBT

Figure 6.10 Chemical structures of DPG and DOTG

Figure 6.11 Chemical structures of TMTD, TETD and TMTM

Figure 6.12 Chemical structures of ZDMC and ZDEC

Dithiocarbamates are considered as medium modulus accelerators but active at

Figure 6.13 Chemical structures of ZDBC, ZEPC and PPDC

Phosphorus-based compounds represent a second group of rapid curing accelerators,

Figure 6.14 Chemical structure of ZBPD

Figure 6.15 Chemical structures of ZIX and ETU

The use of thioureas is diminishing due to toxicological concerns.