Scribd
Upload
64 views

GSV5 SMS Commands English

This document contains SMS commands for configuring communication channels and heartbeat settings for a monitoring device. The commands allow setting parameters such as enabling/disabling channels, setting IP/port, protocol, network protocol, account numbers, APN settings, enabling heartbeat, and heartbeat time. Each command is prefixed by a user code and sets a specific parameter, such as enabling channel 1, setting the IP/port for channel 1, setting the protocol for channel 1, etc.

Uploaded by

Elshan Huseyn
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
64 views

GSV5 SMS Commands English

This document contains SMS commands for configuring communication channels and heartbeat settings for a monitoring device. The commands allow setting parameters such as enabling/disabling channels, setting IP/port, protocol, network protocol, account numbers, APN settings, enabling heartbeat, and heartbeat time. Each command is prefixed by a user code and sets a specific parameter, such as enabling channel 1, setting the IP/port for channel 1, setting the protocol for channel 1, etc.

Uploaded by

Elshan Huseyn
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 1

GSV5 SMS COMMANDS

CH1USED STATE Enable/disable reporting channel 1 (STATE = 1 - enable; STATE = 0 -disable) 1111CH1USED:1 1111 – user code (every command must start with used code); Channel 1 is enabled
CH1USED Habilitar / deshabilitar el canal de informes 1 (ESTADO = 1 - habilitar; ESTADO = 0 - deshabilitar)

CH1IPPORT IPPORT Set IP and PORT for channel 1 (IPPORT format = ip:port) 1111CH1IPPORT:221.55.43.211:12000 Channel 1 ip set to 221.55.43.211 and port 12000
CH1IPPORT Configurar IP y PUERTO para el canal 1 (formato IPPORT = ip: puerto)

CH1PROTOCOL PROT Set protocol for channel 1 (PROT = 0 – E2; PROT = 1 – CSV IP; PROT = 2 – FIBRO; PROT = 3 – SIA) 1111CH1PROTOCOL:0 E2 protocol selected for channel 1
CH1PROTOCOL Configure el protocolo para el canal 1 (PROT = 0 - E2; PROT = 1 - CSV IP; PROT = 2 - FIBRO; PROT = 3 - SIA)

CH1NETPROTOCOL NPROT Set network protocol for channel 1 (NPROT = 0 – TCP; NPROT = 1 – UDP) 1111CH1NETPROTOCOL:0 TCP network protocol for channel 1
CH1NETPROTOCOL Configure el protocolo de red para el canal 1 (NPROT = 0 - TCP; NPROT = 1 - UDP)

CH1ACC ACC Set account number for channel 1 (ACC format = 4 hexadecimal digits, except A (0..9, B, C, D, E, F)) 1111CH1ACC:4BF9 Account number set to 4BF9
CH1ACC Establezca el número de cuenta para el canal 1 (formato ACC = 4 dígitos hexadecimales, excepto A (0..9, B, C, D, E, F))

CH1PSTN STATE Set to use client account number from PSTN event (STATE = 1 - enable; STATE = 0 -disable) 1111CH1PSTN:1 Use client account number from PSTN event
Configure para usar el número de cuenta del cliente del evento PSTN (ESTADO = 1 - habilitar; ESTADO = 0 -deshabilitado)

CH2USED STATE Enable/disable reporting channel 2 (STATE = 1 - enable; STATE = 0 -disable) 1111CH2USED:0 Channel 2 is disabled (other channel 2 settings will not matter until channel is not used)
Habilitar / deshabilitar el canal de informes 2 (ESTADO = 1 - habilitar; ESTADO = 0 - deshabilitar)

CH2IPPORT IPPORT Set IP and PORT for channel 2 (IPPORT format = ip:port) 1111CH1IPPORT:mycmsstation.com:55000 Channel 2 ip set to mycmsstation.com and port set to 55000
Establezca IP y PORT para el canal 2 (formato IPPORT = ip: puerto)

CH2PROTOCOL PROT Set protocol for channel 2 (PROT = 0 – E2; PROT = 1 – CSV IP; PROT = 2 – FIBRO) 1111CH1PROTOCOL:2 FIBRO protocol selected for channel 1
Establecer protocolo para el canal 2 (PROT = 0 - E2; PROT = 1 - CSV IP; PROT = 2 - FIBRO)

CH2NETPROTOCOL NPROT Set network protocol for channel 2 (NPROT = 0 – TCP; NPROT = 1 – UDP) 1111CH1NETPROTOCOL:0 TCP network protocol for channel 1
Configure el protocolo de red para el canal 2 (NPROT = 0 - TCP; NPROT = 1 - UDP)

CH2ACC ACC Set account number for channel 2 (ACC format = 4 hexadecimal digits, except A (0..9, B, C, D, E, F)) 1111CH1ACC:1234 Account number set to 1234
Establezca el número de cuenta para el canal 2 (formato ACC = 4 dígitos hexadecimales, excepto A (0..9, B, C, D, E, F))

CH2PSTN STATE Set to use client account number from PSTN event (STATE = 1 - enable; STATE = 0 -disable) 1111CH2PSTN:0 Use client account number set with CH2ACC command
Configure para usar el número de cuenta del cliente del evento PSTN (ESTADO = 1 - habilitar; ESTADO = 0 -deshabilitado)

APN APN Set APN (ask your network provider) 1111APN:myapn Apn set to myapn
Establecer APN (pregunte a su proveedor de red)

APNUSERNAME USER Set user name (ask your network provider, leave blank if not required) 1111APNUSERNAME:myapnuser Apn username set to myapnuser
Establecer nombre de usuario (pregunte a su proveedor de red, déjelo en blanco si no es necesario)

APNPASSWORD PASS Set password (ask your network provider, leave blank if not required) 1111APNPASSWORD: Apn password is empty (that way password field is cleared if there was something before)
Establecer contraseña (pregunte a su proveedor de red, déjelo en blanco si no es necesario)

HEARTBEAT STATE Enable/disable heartbeat to CMS (STATE = 1 - enable; STATE = 0 -disable) 1111HEARTBEAT:1 Heartbeat is enabled for channel 1 and channel 2 (if those channels is enabled)
Habilitar / deshabilitar el latido del corazón en CMS (ESTADO = 1 - habilitar; ESTADO = 0 - deshabilitar)

HEARTBEATTIME TIME Time between heartbeat events (TIME from 10sec to 65000sec) 1111HEARTBEATTIME:10800 Heartbeat time is set to 10800 seconds = 3 hours
Tiempo entre eventos de latidos del corazón (TIEMPO de 10 segundos a 65000 segundos)

HEARTBEATPSTN STATE Set to use client account number from last PSTN event (STATE = 1 - enable; STATE = 0 -disable) 1111HEARTBEATPSTN:1 Heartbeat packet will use client account number from PSTN event
Configurado para usar el número de cuenta del cliente del último evento PSTN (ESTADO = 1 - habilitar; ESTADO = 0 -deshabilitado)

Page 1

You might also like