Scribd
Upload
88 views2 pages

Fueltech Usa 475 Wilbanks DR Zip Code 30107 Ball Ground - GA Phone: +1 855 595 FUEL (+1 855 595 3835) E-Mail

The document provides instructions for installing and using FuelTech's CAN Updater software to update the firmware on FuelTech modules. It explains how to install the software, connect the USB-CAN converter to the computer, select the correct module and language, and initiate the update process. It also describes what to do in case of errors during the update.

Uploaded by

Franco Madera
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
88 views2 pages

Fueltech Usa 475 Wilbanks DR Zip Code 30107 Ball Ground - GA Phone: +1 855 595 FUEL (+1 855 595 3835) E-Mail

The document provides instructions for installing and using FuelTech's CAN Updater software to update the firmware on FuelTech modules. It explains how to install the software, connect the USB-CAN converter to the computer, select the correct module and language, and initiate the update process. It also describes what to do in case of errors during the update.

Uploaded by

Franco Madera
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

FUELTECH USA

475 Wilbanks Dr
Zip Code 30107
Ball Ground - GA
Phone: +1 855 595 FUEL (+1 855 595 3835)
E-mail: [email protected]
http://www.fueltech.net
FuelTech CAN Updater Software Install Guide
3 – Click “Update Firmware” button and wait for the updating process to finish. Avoid
Insert the FuelTech CD in CD-ROM drive. Go to “My Computer” and access the “CAN
moving the module and pressing its buttons during the update process.
Updater” folder on the CD.
 Windows XP: double click on
“SetupCanUpdater_x.xx_webinstall.exe”.
 Windows 7 or Vista: right click on
“SetupCanUpdater_x.xx_webinstall.exe” and select “Run
as Administrator”.

- Select the software language;

Follow on screen instructions to install .NET Framerwork (in case a message is shown).
Otherwise, just wait for the installation to finish. When the installation is successfully an
FuelTech CAN Updater icon will be created at the Desktop. Double click it to start the CAN
Updater software.

Connecting the USB-CAN Converter on the Computer


Only connect the USB-CAN Converter after the installation of the software, following the
steps above.
Use the rear USB ports of your computer, because front USB ports are more susceptible
to assembly errors or defects due to frequently use.
Error during Update
In case of any error during the update process due to a bad contact, power loss or any
On notebooks, use only USB ports where the USB-CAN Converter fit firmly, a bad
other problem, disconnect the USB-CAN Converter from the computer and from the FT
contact during the update process could corrupt data on the FT module. This repair could
module. Close the CAN Updater software and then open it again, reconnect the USB-CAN
only be done at the factory.
Converter and the FT module. Try to update again. In case the error persists, the software
will automatically generate a log file located on C:\Program Files\FuelTech\FuelTech CAN
Updating a FT on FuelTech CAN Updater Updater\Log_UpdaterCan.txt.
1 – Connect the FT module on the USB-CAN Converter. Contact FuelTech Support via the contacts at the end of this manual with this log file.
2 – Select the correct FT model wich you want to update and the desired language

You might also like