100% found this document useful (1 vote)
892 views30 pages

ASK - 2000 Instruction Manual: Fuji Photo Film Co., LTD

1) This document is the instruction manual for the ASK-2000 printer. It provides safety warnings and instructions for setup, operation, maintenance and troubleshooting. 2) The manual warns that death or serious injury can result from improper handling or ignoring warnings. It instructs the user to stop using the printer if it emits smoke, feels hot, smells strange or makes unusual noises. 3) Setup instructions are provided for unpacking the printer, installing paper and ink ribbons, and setting the print tray. Maintenance tips include cleaning procedures to keep the printer functioning properly. Troubleshooting help addresses issues like ribbon breaks, paper feed problems and print quality.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
100% found this document useful (1 vote)
892 views30 pages

ASK - 2000 Instruction Manual: Fuji Photo Film Co., LTD

1) This document is the instruction manual for the ASK-2000 printer. It provides safety warnings and instructions for setup, operation, maintenance and troubleshooting. 2) The manual warns that death or serious injury can result from improper handling or ignoring warnings. It instructs the user to stop using the printer if it emits smoke, feels hot, smells strange or makes unusual noises. 3) Setup instructions are provided for unpacking the printer, installing paper and ink ribbons, and setting the print tray. Maintenance tips include cleaning procedures to keep the printer functioning properly. Troubleshooting help addresses issues like ribbon breaks, paper feed problems and print quality.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 30

ASK – 2000

INSTRUCTION MANUAL

First edition
April 2006

FUJI PHOTO FILM CO., LTD.

FCC Compliance Statement


WARNING

Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

Properly shielded and grounded cable and connectors must be used for connection to host
computer and / or peripherals in order to meet FCC emission limits.

• NOTICE
Operation is subject to the following two conditions

(1) This device may not cause interference, and


(2) This device must accept any interference received, including interference that may cause
undesired operation of the device
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

- Reorient or relocate receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

For customers in Canada


NOTICE
This class B digital apparatus complies with Canadian ICES-003.

This device is in conformity with the provisions of the EMC Directive (89/ 336/ EEC) and Low
Voltage Directive (73/ 23/ EEC).

Huomio : SUOMI
Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan
Merk : NORSK
Apparatet må kun tilkoples jordet stikkontakt
Varning : SVENSKA
Apparaten skall anslutas till jordat uttag
Contents
�������������������������������������������������������������������������
Safety Notice � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �

Safety/ Transfer ������������������������������������������������������������������������������������������������������� 2

Installation ������������������������������������������������������������������������������������������������������������������� 3

Power supply �������������������������������������������������������������������������������������������������������������

Operation/ Safekeeping/ Cleaning ������������������������������������������������������������������������� 5


Disuse/ Other on operation ������������������������������������������������������������������������������������� 6

How to handle paper and ribbon ����������������������������������������������������������������������������� 6

Preparation
Unpacking ������������������������������������������������������������������������������������������������������������������� 7

installation (Important) ��������������������������������������������������������������������������������������������� 7

Altering paper guide width ��������������������������������������������������������������������������������������� 8

INSTRUCTION Manual
1. Overall View
(1) Front and Rear ����������������������������������������������������������������������������������������������� 9

(2) Ink Ribbon Tray ������������������������������������������������������������������������������������������� 10


(3) Print Head ����������������������������������������������������������������������������������������������������� 10

(4) Paper Tray ����������������������������������������������������������������������������������������������������� 10

2. LED
(1) LED lighting explanation ����������������������������������������������������������������������������� 11

(2) Cut button ����������������������������������������������������������������������������������������������������� 11

(3) Power switch ������������������������������������������������������������������������������������������������� 11

3. Operation
(1) Setting paper roll ����������������������������������������������������������������������������������������� 12

(2) Setting ink ribbon ����������������������������������������������������������������������������������������� 16

(3) Setting of slug box and print tray ��������������������������������������������������������������� 18

(4) Checking before printing operation ����������������������������������������������������������� 18


4. Daily Maintenance ����������������������������������������������������������������������������������������������� 19

Emptying slug box ����������������������������������������������������������������������������� 19

Cleaning Feed Section ��������������������������������������������������������������������� 19


Print Head ������������������������������������������������������������������������������������������� 20

Pinch roller ����������������������������������������������������������������������������������������� 20

Monthly maintenance ��������������������������������������������������������������������������������������� 21

Cleaning of air filter

5. Troubleshooting
(1) Ribbon break down ������������������������������������������������������������������������������������� 22

(2) Damage at paper leading edge ����������������������������������������������������������������� 23


(3) White dots on print ��������������������������������������������������������������������������������������� 23

6. Error messages
(1) Error messages requiring power off/on cycle ����������������������������������������� 24
(2) Recoverable Error ��������������������������������������������������������������������������������������� 25
7. Specification ������������������������������������������������������������������������������������������������������� 26

SAFETY NOTICE �
Before you begin using your ASK-2000,readthis m anualcarefully to becom e fam iliar with how
to operate your ASK-2000
Once you’ve readthis m anual,keep ithandy in case you needto refer to itlater.

The icons usedin this m anualare intendedto preventinjury or dam age to property.Safety
notices are presentedin two form ats,“W arning” andCaution”.M ake sure you understandwhat
they m ean before reading the restof this m anual.

WARNING � Death or serious injury can result from ignoring

warnings and handling the product improperly.

CAUTION � Injury or damage to property can result from ignoring

cautions and handling the product improperly.

If you have som e question aboutoperation and m aintenance,


e,please contactto your technical
alc
representative.Also if any of abnorm alconditions occurs,stopusing the printer im m ediately to
turn off power and contactto your technicalrepresentative.
e.

NOTICE ON SAFTY ������������������


If any of follow conditions occurs, stop using the printer immediately, turn off
the power switch on the front of printer, and unplug the printer from the main
power socket. Make sure the burning has stopped and then contact your
WARNING technical representative to request repairs

Operating this printer when it is emitting smoke, is unusually hot to the
touch, is emitting an unusual odor or noise, or is in any other abnormal
state.

If water gets into the printer.


If foreign object get inside the printer.

Do not continue to use the printer, or you risk fire or electric shock.
If any of above conditions occurs, stop using the printer immediately, turn off
the power switch on the front of printer, and unplug the printer from the main
WARNING power socket. Make sure the burning has stopped and then contact your
technical representative to request repairs. Never attempt to repair this printer

����������������
yourself, because this can be extremely dangerous.

NOTICE ON TRANSFER


Turn off of power switch and disconnect power plug from the main power
WARNING socket to prevent in fire or electric shock.

Do not give a shock to the printer. It will result in fire or electric shock.

Be careful with your waist, when installation or carrying the printer. Since this
printer is heavy. Also use two or more persons to unpack or move the printer.

CAUTION

NOTICE ON INSTALLATION ��������������


This printer for exclusive use of indoor.
Do not use the printer to outside, or you risk fire or electric shock.

WARNING
Connect the ground cable to ground connection.
If leakage of electricity is occurred it result in fire or electric shock.

WARNING

Do not install the printer as at following place



Do not place to unstable place.
Printer may drop or fall down with an injury.
CAUTION (Install the printer to durable place with horizontal)

Do not place the printer in humid or dusty locations; you risk fire or electric
shock.

Do not expose the printer to oil, smoke or steam, you risk fire or electric
shock.

Do not place the printer at directly exposed to the sun or high temperature
area.

Do not place the printer in cramped or poorly ventilated locations such as
lockers, racks or bookcases.

Do not place the printer near area of anti-fire provisions.

Do not place the printer near flammable liquid.
Be careful follow to prevent you risk fire or electric shock

Do not cover the printer with a tablecloth or similar covering.

CAUTION Do not turn over the printer.

Do not block the printer ventilation grilles.

NOTICE ON POWER SUPPLY ��������������


Do not connect the printer to any voltage other than the indicated power supply
voltage. You may have to risk fire or electric shock.

WARNING (AC100~240V single phase)

Be careful follow to prevent you risk electric shock



Do not touch the power plug during a thunderstorm.

WARNING Never plug in or unplug the printer with wet hands.

Be careful follow to prevent you risk fire or electric shock



Check enough capacity of electric current.

Make ground connection surely.
WARNING �
Do not connecter the printer to any
(Power consumption � Rated electric current ��������������������� )

Check and install the power cable more safety to prevent plug come away
in person legs.

Be careful follow to prevent you risk fire



Do not use power cable with dusty

WARNING Do not wiring same power line with air-condition, copy machine so on.

Be careful follow to prevent you risk fire or electric shock



Turn off the printer power switch before disconnect cable from the printer.

Do not use power cable continuity, when power cable has damaged.

CAUTION Stop to use power cable, when plug is loosen.

Do not bend strongly and crush power cable.

Do not remove the printer’s power cable from the power socket by pulling
on the cable. Doing so could damage the cable and lead to fire or electric
shock. Always grasp the plug itself and pull.

Keep away power cable from heating appliance.

Insert connecter of power cable completely to power plug.

NOTICE ON OPERATION ����������������


Be careful follow during operation to prevent you risk fire or electric shock

Do not modify the printer by yourself. Contact to your technical
representative for repair, readjustment and inspection.

WARNING Do not place flower vases, plant pots, cups or other vessels containing
cosmetics, medicines or water on top of printer.

Do not give a shock.

Do not place small metal objects on top of printer. Such items could spill or
fall inside the printer and cause fire or electric shock.

Do not use continuity the printer, if the printer has got water, liquid or small
metal.

Do not do abnormal operation.
The printer is damaged and you may suffer injury.

Do not do operation with removed cover.
Do not torch the thermal head few minutes after making print. You may have
burn by heat.

CAUTION
Do not torch gears. You may have injury to pinch

CAUTION

NOTICE ON SAFEKEEPING

��������������
Turn off the power switch and disconnect power cable from the printer for
safety, if you do not use the printer over an extended period of time.

CAUTION

NOTICE ON PRINTER CLEANING



������������
For safety, always remove the plug from the power socket whenever
cleaning the printer. Failure to disconnect the power may cause electric

WARNING shock.

NOTICE ON DISUSE ������������������


Obey municipal or government ordinance to keep nature environment, when
life of the printer is end and throw away it.

WARNING

OTHER NOTICE ON OPERATION

Be careful also following items with operation



Do not give damage or vibration to the printer. This is a precision machine.
It may cause machine down.

Do not carry the printer with paper, ribbon and accessory into the printer together. And use the

packing box came from factory. It may cause machine down.



Stop to use the printer for a moment with power off, if the printer has had moisture due to the

printer moved from cool area to warm area so on. This applies paper and ribbon. Printer has
whether paper and ribbon jamming or machine down.

Do not turn switch off the printer during operation with no problem.

There is fear to eliminate data and program from the printer.



Do not install the printer near TV, trance, motor, speaker, magnet and so on (magnetic substance).

It may cause machine down.



Do not install near TV and radio.

Printer generate an electric wave, and receiver receives jamming.

HOW TO HANDL PAPER AND RIBBON



Use glove when touching paper.

If you touch a paper with one'


s bare hands for setting paper, print may have dirtied.

For keeping paper and ribbon, following condition is necessary
< Temperature: less than 30� , Humidity: less than 70% >

Use genuine paper and ribbon only. If you use other company’s paper, printer has paper or ribbon
jamming or machine down with no service and repair.

Preparation
Unpacking

Warning: The ASK-2000 unit is heavy and requires 2 people to carry.

� Please open the box and find ASK and its accessories.

Standard accessories fig.1


1. Print Tray
2 2. Instruction Manual
3. Print samples (adjustment data)
3 Label (Operation panel LED)

1
Attention:
Please keep test prints in safe place as they
Standard accessories may be used as density reference if/when Print
Head may need to be replaced.

Installation(Important)
Place ASK-2000 and PC in position
Step 1. Connect ASK-2000 and PC with USB cable
� USB cable is not included in the package
Step 2. Connect the AC power
� Input power voltage AC100V – 240V (single phase)

ASK-2000
USB Cable
Rear Side

PC
Windows 2000/XP

AC Power cable * Power Switch is at the front side

Microsoft, Windows are registered trade mark of Microsoft Corporation in US and other countries

7
Altering paper guide width
Paper width may be switched between 6”(152mm) and 5”(127mm).

(Attention)

ASK-2000L is set for 5” (127mm) at the factory

ASK-2000K is set for 6” (152mm) at the factory

Paper width change: Shift paper guide (left/right) positions

By opening the front door, you will find white color of the paper guides.
Step 1: Remove the fixing screw of left/right paper width guide (white)

Step 2: Shift paper guide position to find the fixing position of the desired width.

Step 3: Fix the position using the fixing screw.

Step 4: Attach the spacer for 5” (127mm) width to left/right paper core guide.

Note: Spacer is not needed when 6” (152mm) paper is used.

Paper width guides


Fixing screws

Paper width guides Remove fixing screws and to shift guide positions

Spacer for 127 mm paper

152 127 127 152

Paper core

Adjust for correct size by shifting guide positions Set spacers in case of 5” (127mm) paper

Instruction Manual
1. Overall View
(1) Front and Rear

Door Open Lever

Air Filter

Slug Box
Power Switch

LED

Front Rear

USB2.0

AC Power Cable

Rear

Warning � To avoid electrical shock, always ensure hands are dry


when inserting power cable.

Warning � Connect the ground cable to ground connection.


If leakage of electricity is occurred it result in fire or electric shock.

(2) Ink Ribbon Tray


� By opening the front door, you will find supply ribbon gears and bobbin bearings

Rear

Front: Ribbon Supply


Rear: Ribbon Take-up

Front

Ink Ribbon Tray

(3) Print Head


� By opening the front door, you will find Print Head at inside Printer.

Caution:
Do not touch Print Head when Power is on and
immediately after switched off power.

*Could burn your fingers

Print Head *Could cause damage to the Head

Print Head

(4) Paper Tray


� By opening the front door, you will find paper core

Paper core shaft

Paper Tray

10

2. LED

Blue LED (Upper) STATUS


Red LED (Lower) ERROR

Paper Cut Switch

Left view Power Switch Right view

For descriptions
(1) LED lighting explanation on errors, please
refer to Part 6
The LED indicates current printer condition with combination
(error messages).
between condition of STATUS (Blue) and ERROR (Red).

Blue LED Red LED Explanation


(Upper) (Lower)

OFF OFF Power Off state

BLUE Ready
OFF
LIT

BLUE Transferring image data


OFF
Flash
BLUE RED Error during Initializing which can be reset.
LIT LIT

BLUE RED Error during Image transfer.


Flash LIT The error can be reset.
BLUE RED Error.
LIT Flash Power needs to be cycled off/on
BLUE RED Error during image transfer.
Flash Flash Power needs to be cycled off/on.

(2) Cut button


Pressing cut button while LED is at blue ready state will cause roll paper leading edge to be
chopped off (about 11 cm)

(3) Power Switch


Pressing the Power Switch will turn on and turn off the power

11

3. Operation
(1) Setting roll paper
(Note 1) Use of cloth gloves is recommended while handling the roll paper.
(Fingerprints may stick to prints to cause problem on printed image)
(Note 2) If paper end or ribbon end is reached during operation, please replace both roll
paper and ribbon at the same time with keeping the power of the printer on.

* If paper end is reached during continuous printing, print will automatically continue
after setting paper.
* If power is turned off during the operation of changing paper/ribbon, data will
be lost.
* One roll paper and one Ink ribbon are both designed to make 600 prints of 6x4” size.
When one (roll paper or ink ribbon) becomes empty, please replace both at the
same time.

Preparation: Prepare new roll paper and new ink ribbon


ASK-2000 power should be on

STATUS LED (Upper)


Ink Ribbon
ERROR LED (Lower)

By turning on the power


switch, Status LED
(blue) and Error LED
(red) will turn on

Roll Paper

Paper and Ink Ribbon LED

12

Step 1. Open front door

*By releasing the lever, front door will come forward and open.

Lever

Release the door open lever Inner side of front door

Step 2.
By releasing the lock levers which lock both ends of paper core, pull out the paper core

Lock lever

Pull lock lever in the arrow direction Tip over the lock lever

Paper core
Lever in release position

Do the same for left and right Pull out paper core
13
Step 3. Remove left plate (red) with pushing the black button from the paper core shaft

Push the black button

Removing left plate Left plate has been removed


Step 4 � Set roll paper to the paper core shaft

Right plate Left plate

NOTE: When paper sets to the right plate, check paper direction to see an
arrow of label as picture. If opposite, paper can not set correctly to printer.

Push in roll paper to right plate Push in left place


Step 5. Be sure to check the lock with pushing red plate. Roll paper set core should be
securely fit into the Printer and set locking levers. Join red colors.

Set red plate of paper core into red


block of paper tray.

Push red area

Push red area until locking plate Set paper core and lock the locking lever

14

Step 6. Remove seal at the paper leading edge.


Insert paper leading edge until it reaches the paper set position.

Roller
Insert paper
(Silver)
between
rollers

(Note) Direction to remove the Roller (white)


seal (to the front)

Set roll paper Insert paper edge between rollers

Setting Roll Paper

Roller (white) Paper

Guide plate

Guide plate Roller (silver)


Right
Sensor
Insert paper leading edge into guide plates

(Note) Paper is set correctly when the paper leading edge


reaches the sensor positioned at the rear side of
the guide plate.

LED: Paper set


Blue lit Blue flashing

Sensor position
Insert paper until blue LED starts to flash Red lit Red lit

Paper set position LED state when paper setting is complete

15
(2) Setting Ink Ribbon
� Set Ink Ribbon after setting Roll Paper

Take-up side (White)

Supply side Take-up side Supply side (Black)

Ink Ribbon Ink Ribbon Tray

Step 1 Set Ink Ribbon as shown below.


� First, set Supply side ribbon at the position closer to front then set Take-up side.

Supply side

Spring

Aim at the middle of the bearing Do not leave space to gear

Push to the left bearing Set ribbon while keep pushing to the left

Spring

Set at the middle of the bearing

Leave no space to the gear

Take-up side

Push towards right bearing Set ribbon while keep pushing to the right

16
Remove ribbon sag Roll Paper and Ink Ribbon are correctly set

(Note) If there is sag on ribbon after setting it, please remove ribbon sag by rotating the
take-up gear

Step 2. After setting paper/ribbon, close the front door until it becomes securely locked.

Close front door securely

Step 3. Operation after closing front door


If paper was set with ASK-2000 power on,
� After initial movement, paper leading edge will be chopped off for five times (10cm x 5) and Printer
will become Ready

If paper was set while ASK-2000 power was off,


� After initial movement, Printer will become Ready

(Note) In this case, there will be no chopping off of paper

17

(3) Setting of Slug Box and Print Tray

Slug Box

Hooks for Print Tray should be


Print Tray inserted here

Slug Box and Print Tray


Position to set Print Tray

Hook lever of the print tray to hole of the


front door as left side picture.

Front door Paper tray

Setting and removing of Slug Box


� Removing of Slug Box Setting of Slug Box

Lock

Pull out Slug Box Set Slug Box in place


(Note) Before you operate the printer, please make sure to clean the cut slug from
the box (up to 600 cut slugs can be stored in the slug box)

(4) Checking before printing operation


1. Power for PC and ASK on? � �Note Please do not open front door
2. Is ASK Ready (LED blue is lit)? during printing (Safety function will
force to stop the printing operation).

18
4. Daily Maintenance
Please make sure that dust will not enter into the printer
If you find symptom on print that may be caused by dust, please clean feed
roller inside the front door, Print Head, paper tray and ribbon tray sections.

(Note) Please use ethyl alcohol or isopropyl alcohol as cleaning solvent.

Emptying Slug Box


Before operation, please make sure to take out
and empty slug box.

Slug Box

Cleaning feed section



Please clean the paper tray section and feed roller of platen roller with clean
and wet but well squeezed cloth.

For dirt, which is difficult to remove such as by small portion of ribbon sticking,
please clean using soft cloth (like gauze) wet with ethyl alcohol.

Paper Tray
Platen roller of paper roller (Black)

Remove roll paper with paper core


for cleaning

Feed roller of platen roller Paper Tray Section



19

Print Head
� To clean Print Head, please use dry soft cloth like a lens cleaner.
� Do not use ethyl alcohol against head damage.

(Note) By opening the front door, you will find Print


Head inside

Caution:
Do not touch Print Head while power is
on or immediately after operating the
Print Head printer.
• Could cause burn to fingers
• Could cause damage to Print Head
Print head

Pinch Roller

Clean the Pinch Roller with clean cloth soaked with clean water.

If dirt from ribbon sticks and is difficult to remove, please clean it with a soft

cloth such as ethyl alcohol-soaked gauze.

Protect cover Pinch roller

The snap hook

Pull the snap hook and remove protect cover Clean pinch roller

20

Monthly maintenance

(Note) If filter is extremely dirty, please replace it with a new filter


(Replace after 3 to 6 months)
Cleaning air filter
� Remove air filter as following procedure and sweep air filter clean.
� (These air filters are static electricity type. Do not wash quite air filter, since
efficacy goes down and printer may has trouble. )

Filter cover

Air Filter Cover Remove cover

Clean cover and around cover with wet towel Right side

Air Filter Filter cover

Replace air filter Air Filter Cover

Air Filter

Remove cover Replace air filter


21
5. Troubleshooting
(1) Ribbon break down

Turn off ASK power and follow steps described below.

Step 1. Open front door, apply tape to put together the cut off portion of the ink ribbon

Tape

Ribbon break. Put together broken ribbon by tape

Step 2. Wrap the ribbon a few times around take-up core

* Ribbon set position


Ribbon should be set in a way that OP (transparent
area of the ribbon) is positioned in the area
between unused ribbon and take-up core.
Rotate ribbon core to the ribbon set position with
removing the ribbon crease. Front side is
Supply core and Rear side is Take-up core.

Wrap the ribbon a few times around take-up core and remove ribbon crease

(Note) Please check the paper. If a half processed print is on the paper, please be sure to cut
off this portion before setting the paper roll in position

Step 3. Turn on power of ASK. After making sure that Error LED (red) went off, press cut
button to chop off paper leading portion (10 cm)

22
(2) Damage at paper leading edge
Turn off power of ASK and follow steps described below.
Step 1. Open front door, check to see if paper jam is found in the paper feed section by
taking out the paper leading portion.
Step 2. Cut off damaged portion of the paper in straight line using scissors, if there is
damage.
Step 3. Wind back the paper leading portion to the Roll paper.
Step 4. Turn on ASK power. Set Roll Paper and Ink Ribbon again.
Step 5. After checking that the LED is in Ready state (blue lit), press cut button to chop
off paper leading portion (10 cm)

Cut

Take out paper leading portion (such as for Z folded) Cut off paper leading portion

(3) White dots on print


Please turn off ASK power before taking following steps.

Symptom: White dot appears in fixed interval on print in the direction of paper feed

Direction of
paper feed
Remove cover and clean Pinch roller

Measure: Dirt or dust may be clinging to pinch roller. Please clean the Pinch Roller
with clean cloth soaked with clean water. If the dirt sticks firmly into the
roller, please remove it with finger nails.

23
6. Error messages
(1)Error messages requiring power off/on cycle
Error No. Description
����� �����������������������������������������
E01 ��� ������������������������������� �������
����� ���������������������������������������������
E02 ��� ������������������������������� �������
����� � ������������������� �������
E03 ��� ��������������������������� ������������������������������������� �������
����������� ����������������������� � ���
E04 ��� ������������������������������� �������
����� � ���������������������������������������������������
E05 ��� ��������������������������������������������������������������� �������
����������������������� ����������� ����� ������������� �������������
E06 ��� ��������������������������������������������������������������� �������
����������������������������������� ���
E07 ��� ������������������������������� �������
���������������������������������������
E08 ��� ������������������������������� �������
��������������� ��� ����� ����� �����������
E09 ��� ������������������������������� �������
����� � ������� ��������������������� �
E10 ��� ������������������������������� �������
����� � ������� ������� ������� � �������������������
E11 ��� ������������������������������� �������
��� ������������������������������������������� ��������� ������������� �������
E12 ��� ������������������������������� �������
��� ������������������������������������������� ��������� ������������� �������
E13 ��� ������������������������������� �������
��� ����������������������������� ������������������������� �������
E14 ��� ������������������������������� �������
��� ����������������������������� ������������������������� �������
E15 ��� ������������������������������� �������
����� � ������������� ����� �������������
E16 ��� ������������������������������� �������

24

(2)Recoverable errors

Error No. Description


����� ��������� �����������������
W50
��������� �������������������
W51 ��� ��������������� ��������������������� �������
��� ����������� ����������������������� ������������������������� ������� �������
W52 ��� ����������������������������� ������������� ������������������� ������������� �����
������������������� ���������
W53 ��� ����������� �������������������
��������� ��������� �������������
W54 ��� ������������������� ������� �������
����� ������������� �����������
W55 ��� ��������������� ����������������� �����������
����������������������������������������������� �
W56 ��� ������������������������������� �����������
��� ����������� ����������������������� ������������������������� ������� �������
W57 ��� ����������������������������� ������������� ������������������� ������������� �����
������������������� ���������
W58 ��� ����������� �������������������
��������� ����������� ������� � ���������������
W59 ��� ������������������� ����� ����������� �
��������� ����������� ������� � �������������������
W60 ��� ������������������� ����� ����������� �
����� ��������� ��� ��� ��� ��� � ��� ���
W61 ��� ������������� ��������������� � �
����� � ����������������������������� ���������������
W73 ��� ������������������������� ������� �������
��������� ��������� �����������������
W78 ��� ������������������������� ������� �������
������������� ��������� ��� ����� �����������������
W79 ��� ����������������������������� �����������

25

7. Specification

Item Specification
Type Dye Sublimation Printer
Print Head 300 dpi (Dual Line Print Head)
Print Resolution 300X600dpi
Gradation 16.7 million colors, full color
Maximum Print Width 154 mm
Print Speed About 8 seconds (6x4 inch)
Interface USB 2.0
Buffer Memory 64 MB (32 MB x 2)
OS Windows 2000/XP
5 x 3.5” (127x 89 ��� )
6 x 4” (152 x 102 mm)
Print size
Border­ 5 x 7” (127 x 178 mm)
less 6 x 8” (152 x 203 mm)
6 x 9” (152 x 230 mm)
6 x 4” x 2 (152 x 102 mm x 2)
Paper type Roll paper
Ink Ribbon YMC+OC (Exclusive type Ink Ribbon)
Outer dimensions 300mm(W) � 410mm(D) � 355mm(H)
Weight Approximately 25Kg (not including paper)
Power voltage and power AC 100V to 240V, 50/60Hz Automatic voltage
frequency switching
Power consumption Maximum 315 W

26

You might also like