18W Audio Amplifier - circuit diagrams, schematics, electronic projects http://www.diy-electronic-projects.

com/p12-18W-Audio-Amplifier

Electronic projects
Index Electronics projects categories Search circuits Links Read me! Contact/Submit project Sitemap 310 projects!

Ads by Google Audio Amplifier EMI Amplifier Schematic 2.1 Amplifier Power Amplifier

you are here: home page :: projects :: Audio :: amplifiers :: 18W Audio Amplifier
project categories:
18W Audio Amplifier Audio (49)
PSD835G2-90U
Power & high voltage (43)
Buying obsolete or
allocated parts? Call Radio (23)
1-800-478-9308 today! Light & LED (31)
www.partminer.com/submitRFQ
Tools & measurement (40)
Telephone (18)
circuit diagram Automotive (10)
Microcontrollers (12)
Sensors & control (47)
Timers & oscillators (40)
Miscellaneous (26)

StumbleUpon button

Share this page

project subcategories:
All subcategories
amplifiers
preamps, filters, effects
VU meters & spectrum analyzers
mixers
other

similar projects:
100W RMS Amplifier
10W Audio Amplifier with
Bass-boost
10W Mini Audio Amplifier
Amplifier parts: 200W audio amplifier
P1 = 22K Log.Potentiometer (Dual-gang for stereo) 22 Watt Audio Amplifier
R1 = 1K 1/4W Resistor 25W Mosfet audio amplifier
R2 = 4K7 1/4W Resistor 2N3055 Power Amplifier
R3 = 100R 1/4W Resistor 5,000W ultra-light, high-power
R4 = 4K7 1/4W Resistor amplifier, without switching-mode
R5 = 82K 1/4W Resistor power supply
R6 = 10R 1/2W Resistor 50 Watt Amplifier
R7 = R22 4W Resistor (wire wound) 60W Bass Amplifier
R8 = 1K 1/2W Trimmer Cermet (optional)
C1 = 470nF 63V Polyester Capacitor
C2,C5 = 100uF 3V Tantalum bead Capacitors recently added projects:
C3,C4 = 470uF 25V Electrolytic Capacitors Doorbell for the Deaf
C6 = 100nF 63V Polyester Capacitor High Quality Intercom
D1 = 1N4148 75V 150mA Diode Combinational Conjuring Trick
IC1 = TLE2141C Low noise,high voltage,high slew-rate Op-amp POT-PLANT POWER
Q1 = BC182 50V 100mA NPN Transistor Ultrasonic Dog Whistle
Q2 = BC212 50V 100mA PNP Transistor Quiz Circuit
Q3 = TIP42A 60V 6A PNP Transistor LED Torch
Q4 = TIP41A 60V 6A NPN Transistor Insect Repellant
J1 RCA audio input socket Speaker Microphone Circuit
Magic Wand Conjuring Trick.
Power supply parts:
R9 = 2K2 1/4W Resistor
C7,C8 = 4700uF 25V Electrolytic Capacitors
most popular projects:
500W low cost 12V to 220V
inverter

1 din 2 19.12.2010 21:00

18W Audio Amplifier - circuit diagrams, schematics, electronic projects http://www.diy-electronic-projects.com/p12-18W-Audio-Amplifier

D2 100V 4A Diode bridge Led display digital Voltmeter

D3 5mm. Red LED Basic UPS Power Supply
T1 220V Primary, 15 + 15V Secondary 50VA Mains transformer 100W RMS Amplifier
PL1 Male Mains plug 200W audio amplifier
SW1 SPST Mains switch PlayPIC®
2N3055 Power Amplifier
Notes:
LED Torch
Can be directly connected to CD players, tuners and tape recorders.
12 Volt 30 Amp PSU
Don't exceed 23 + 23V supply.
12VDC Fluorescent Lamp Driver
Q3 and Q4 must be mounted on heat sink.
D1 must be in thermal contact with Q1.
Quiescent current (best measured with an Avo-meter in series with Q3 Emitter) is not
critical.
Adjust R3 to read a current between 20 to 30 mA with no input signal.
To facilitate current setting add R8 (optional).
A correct grounding is very important to eliminate hum and ground loops. Connect in the
same point the ground sides of J1, P1, C2, C3 &C4. Connect C6 at the output ground.
Then connect separately the input and output grounds at the power supply ground.

Technical data:
Output power: 18 Watt RMS @ 8 Ohm (1KHz sine wave)
Sensitivity: 150mV input for 18W output
Frequency response: 30Hz to 20KHz -1dB
Total harmonic distortion @ 1KHz: 0.1W 0.02% 1W 0.01% 5W 0.01% 10W 0.03%
Total harmonic distortion @10KHz: 0.1W 0.04% 1W 0.05% 5W 0.06% 10W 0.15%
Unconditionally stable on capacitive loads

author:
e-mail:
web site: http://www.redcircuits.com/

Index Projects categories Download Links Contact/Submit project Sitemap Disclamer and Privacy policy

2 din 2 19.12.2010 21:00