PHXG-91B, PHWX-81B, Phwu-81b PDF

PHxx series
User and Installation manual
R5905597/00
16/10/2013
Barco nv
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.82.11
Fax: +32 56.36.883.86
Support: www.barco.com/esupport
Visit us at the web: www.barco.com
Printed in Japan
Trademark, Registered trademark
• DLP™, Digital Micromirror Device, DMD and BrilliantColor™ are all trademarks of Texas Instruments.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
• Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States
and/or other countries.
• Mac is a registered trademark of Apple Inc. • The trademark of PJLink is trademark applied for registration or registered trademark
in Japan, the United States, and other countries and areas.
• Crestron RoomView Connected is a trademark of Crestron Electronics, Inc.
• Other brand or product names are trademarks or registered trademarks of their respective holders.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Table of contents
TABLE OF CONTENTS
1. Safety . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. 5
1.1 General considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Using projector in Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.3 Compliance notice of FCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4 Important safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2. Preparing the projector.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 11

2.1 Projector accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.2 Terminology overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.3 Installation of the batteries into the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.4 Using the remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.5 Projector configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.6 Location of ceiling mounting holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.7 Screen setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . 17
2.8 Screen size and projection distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.9 Correcting skewed or distorted image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.10 About fine streaks on the screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3. Connections. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 21
3.1 Removing the covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
3.2 Power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3.3 Connecting the projector to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3.4 Connecting the projector to video equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
3.5 Installing the covers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
4. Getting started .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 29
4.1 Basic Remote control, indications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.2 OSD Lite navigation results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
4.3 Projecting images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
4.4 Stop projecting images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
4.5 Adjusting the position of the projected image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
4.6 When the projected image is distorted or a trapezoid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
4.7 Blanking the screen temporarily . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4.8 Auto position mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5. Advanced menu .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 39
5.1 Starting the advanced menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
5.2 Advanced menus overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
5.3 Image menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
5.4 Installation 1 menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
5.5 Installation 2 menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
5.6 Multi-Screen menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
5.7 FEATURE menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
5.8 SIGNAL menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5.9 NETWORK menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
5.10 INFORMATION menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
6. Adjustments with the ADVANCED menu. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 55

6.1 To adjust the brightness (CONTRAST and BRIGHTNESS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.2 To adjust the color (COLOR and TINT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.3 To sharpen or soften the projected image (SHARPNESS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.4 To adjust the tone of white (COLOR TEMP.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.5 Color Enhancer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6.6 Adjusting the fineness of the image (SUPER RESOLUTION) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6.7 Adjusting the tone of each color (COLOR MATRIX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6.8 Setting the screen size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
6.9 Setting the aspect ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
6.10 Adjusting the detailed setting of ASPECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
6.11 Saving the setting in the SIGNAL MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
6.12 Adjusting a computer image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
6.13 How to adjust the image supplied from the computer using the menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
6.14 Simple method to adjust the image position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.15 LPF (Progressive filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.16 Image displayed on the multi-screen, joints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.17 Adjusting the color variations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
6.18 Resetting the settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
6.19 When the projected image is distorted. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
6.19.1 Adjust using Keystone mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
6.19.2 Adjustment using the CORNERSTONE mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
6.19.3 Adjustment using the CURVED mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
6.20 Changing the AUTO POWER OFF setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
6.21 Setting IMAGE REVERSE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
6.22 Displaying TEST PATTERN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
R5905597 PHXX SERIES 16/10/2013 1

Table of contents
7. Initial network settings .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 75

7.1 Setting Projector Name. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
7.2 Enabling or disabling the network certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
7.3 Network Password Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
7.4 IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
7.4.1 Start up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
7.4.2 Setting or Clearing DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
7.4.3 IP Address Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
7.4.4 Subnet Mask Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
7.4.5 Default Gateway Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
7.4.6 Saving IP CONFIG Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
7.5 Setting the control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
7.6 Initialization of Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
7.7 How to Use Network Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
8. Lamp relay . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 81
8.1 Setting the lamp relay interval, LAMP SELECT is set to DUAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
8.2 Setting the lamp relay interval, LAMP SELECT is set to SINGLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
9. Advanced features . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 85
9.1 Password function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
9.1.1 Enabling the password function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
9.1.2 Cancel the password function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
9.2 Split . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
9.3 Picture in Picture (PIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
9.4 Supervising and controlling by computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
9.5 Monitoring and control using SERIAL terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
9.6 Control by a control panel, etc.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
10. Lamp replacement . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 93

10.1 Lamp replacement warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
10.2 Interval of lamp replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
10.3 Lamp replacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
10.4 Reset of the lamp operation time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
11. Maintenance. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 99
11.1 Cleaning of the projector and the vents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
11.2 Cleaning of the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
11.3 Automatic cleaning filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
11.3.1 Setting the cleaning interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
11.3.2 How to clean the automatic cleaning filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
12. Troubleshooting .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 103

12.1 No image appears on the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103
12.2 Images are not displayed correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
12.3 Other problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .105
12.4 Led . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
13. Specifications . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 107

13.1 Specifications of PHXG-91B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
13.2 Specifications of PHWX-81B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
13.3 Specifications of PHWU-81B. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
13.4 Specification of RGB signals in each computer mode of the projector For PHWU-81B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
13.5 Specification of RGB signals in each computer mode of the projector, For PHWX-81B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
13.6 Specification of RGB signals in each computer mode of the projector, For PHWX-81B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
13.7 Specification of RGB signals in each computer mode of the projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
13.8 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
13.9 Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
A. Option lens H LENS 0.8-1.0, 2.8-4.5 or 4.5-8.7 .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 119

A.1 Lens mounting procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
A.2 Focus correction function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
A.3 Check after mounting the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
A.4 Cleaning of the lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
A.5 Specifications H LENS 0.8-1.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121
B. Optional lens H LENS 1.3-1.8 .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 127

B.1 Lens mounting procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
B.2 Specifications H LENS 1.3-1.8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .128
B.3 Specifications H LENS 2.2-2.7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .129
C. Environmental information .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 133

C.1 Disposal information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
C.2 Rohs compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .133
C.3 Production address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
2 R5905597 PHXX SERIES 16/10/2013

Table of contents
Glossary .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 135
Index. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 137
R5905597 PHXX SERIES 16/10/2013 3

Table of contents
4 R5905597 PHXX SERIES 16/10/2013

1. Safety
1. SAFETY
About this chapter
Read this chapter attentively. It contains important information to prevent personal injury while installing and using a PHxx series
projector. Furthermore, it includes several cautions to prevent damage to the PHxx series projector. Ensure that you understand and
follow all safety guidelines, safety instructions and warnings mentioned in this chapter before installing your PHxx series projector.
After this chapter, additional “warnings” and “cautions” are given depending on the installation procedure. Read and follow these
“warnings” and “cautions” as well.
About the term PHxx series

The following projectors are included in the term PHxx series : PHWU-81B, PHWX-81B and PHXG-91B
1.1 General considerations

Safety labels
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Image 1-1
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to
the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
2000m
Do not use above 2000m above sea level.
WARNING: Ensure you understand and follow all the safety guidelines, safety instructions, warnings and
cautions mentioned in this manual.
WARNING: Be aware of suspended loads.
WARNING: To prevent fire or shock hazard, do not expose the projector to rain or moisture.
R5905597 PHXX SERIES 16/10/2013 5

1. Safety
WARNING: To prevent electric shock, do not use this (polarized) plug with an extension cord; receptacle or
other outlet unless the blades can be fully inserted to prevent blade exposure.
CAUTION: Not for use in a computer room as defined in the Standard for the Protection of Electronic Com-
puter/ Data Processing Equipment, ANSI/NFPA 75.
1.2 Using projector in Europe

Compliance notice
This projector complies with the requirements of the EC Directive 2004/108/EC “EMC Directive” and 2006/95/EC “Low Voltage Di-
rective”.
Warning
This is a EN55022 Class A product. In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
This product may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures
to reduce electromagnetic emissions to prevent interference to the reception of radio and television broadcasts.
Maschinenlärminformations-Verordnung - 3. GPSGV, der höchste Schalldruckpegel beträgt 70 dB(A) oder weniger gemäss EN ISO
7779
1.3 Compliance notice of FCC

FCC notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a com-
mercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the in-
struction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Any changes or modifications not expressly approved by Barco could void the user’s authority to operate this equipment.
1.4 Important safety instructions

General
• All the safety and operating instructions should be read before operating the projector.
• The safety and operating instructions should be retained for future reference.
• All warnings on the projector and in the operating instructions should be adhered to.
• All operating instructions must be followed.
6 R5905597 PHXX SERIES 16/10/2013

1. Safety
To prevent personal injury

• Mercury Vapor Warnings: Keep the following warnings in mind when using the projector. The lamp used in the projector
contains mercury. In case of a lamp rupture, explosion there will be a mercury vapor emission. In order to minimize the potential
risk of inhaling mercury vapors:
- Ensure the projector is installed only in ventilated rooms.
- Replace the lamp module before the end of its operational life.
- Promptly ventilate the room after a lamp rupture, explosion has occurred, evacuate the room (particularly in case of a preg-
nant woman).
- Seek medical attention if unusual health conditions occur after a lamp rupture, explosion, such as headache, fatigue, short-
ness of breath, chest-tightening coughing or nausea.
• Caution: High pressure lamp may explode if improperly handled. Refer servicing to qualified service personnel. The customer
should never attempt to disassemble the lamp casing or to dispose of the lamp casing other than by returning it to Barco.
• Do not place this projector on an unstable cart, stand, tripod, bracket or table. Use only with a cart, stand, tripod bracket, or table
recommended by the manufacturer or sold with the projector. Any mounting of the appliance should follow the manufacturer’s
instructions and should use a mounting accessory recommended by the manufacturer.
• An appliance and cart combination should be moved with care. Quick stops, excessive force and uneven surfaces may cause
the appliance and cart combination to overturn.
• Do not place the projector on uneven surface. Place the projector on a leveled and stable surface only. Please do not place
the projector on unstable surfaces. The product may fall, causing serious damage to it and possible injury to the user.
• Warning: high intensity light beam. Do not look into the lens when it is operating. It may hurt your eyes. Never let children look
into the lens when it is on.
• Do not touch the exhaust vents and bottom plate, which become hot. Do not touch them or put other equipment in front of the
exhaust vents. The exhaust vents and bottom plate, when heated, may cause injury or damage to other equipment. Also, do
not set the projector on the desk which is easily affected by heat.
• Do not look into the exhaust vents when projector is operating. Heat, dust, etc. may blow out of them and hurt your eyes.
• Do not insert your fingers in the space between the lens and the cabinet. The lens may shift causing injury or damage to the
projector.
• Exposure to UV radiation: Some medications are known to make individuals extra sensitive to UV radiation. The American
Conference of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure for an-8hour day to be
less than 0.1 microwatts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure
employees are not exposed to cumulative radiation levels exceeding these government guidelines.
• Warning: Protection from ultraviolet radiation: Do not look directly in the light beam. The lamp contained in this product is
an intense source of light and heat. One component of the light emitted from this lamp is ultraviolet light. Potential eye and skin
hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary exposure. Protect yourself and
your employees by making them aware of the hazards and how to protect themselves. Protecting the skin can be accomplished
by wearing tightly woven garments and gloves. Protecting the eyes from UV can be accomplished by wearing safety glasses
that are designed to provide UV protection. In addition to the UV, the visible light from the lamp is intense and should also be
considered when choosing protective eye wear.
To prevent fire hazard

• Do not place flammable or combustible materials near the projector!
• Do not face the projector lens to the sun. It can lead to fire.
• Slots and openings in the cabinet are provided for ventilation, ensuring reliable operation of the projector and to protect it from
overheating. Do not block these openings or allow them to be blocked by placing the projector on a bed, sofa, , carpet, rug, or
bookcase. Ensure that there is adequate ventilation and that the manufacturer’s instructions have been adhered to.
• Use correct voltage. If you use incorrect voltage, it can lead to fire.
• Do not connect multiple electrical appliances to a single wall outlet. It can lead to fire.
• Do not extend the power cord. It can lead to fire.
• Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols near the projector. Flammable substances
may ignite causing fire or breakdown because the temperature inside the projector rises very high while the lamp is illuminating.
• Be sure to unplug the power cord from the wall outlet if the projector will not be used for a long period of time. Otherwise, it
may cause fire. Important safeguards (continued)
• Do not use the projector in the following locations and manners, which may cause fire or electric shock.
- In a dusty or humid place.
- In a sideways position, or with the lens facing down.
- Near a heater.
- In an oily, smoky, or damp place such as a kitchen.
- In direct sunlight.
- Where the temperature rises high, such as in a closed cabinet.
- Where the temperature is lower than +41ºF (or +5ºC) or higher than +104ºF (or +40ºC).
• Do not cover the lens with the lens cap while the lamp is on.
R5905597 PHXX SERIES 16/10/2013 7

1. Safety
To prevent the risk of electrical shock

• Never add any attachments and/or equipment without the approval of the manufacturer as such additions may result in the risk
of fire, electric shock or other personal injury.
• Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.
• The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your country.
• This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power cables
are the correct one, consult your dealer.
• This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the
type of power, please consult your appliance dealer or local power company.
• Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against
them. Pay particular attention to cords at plugs, convenience receptacles, and points where they exit from the appliance. Do
not put the power cord under a carpet.
• This projector uses the power plug of 3-pin grounding type. Do not take away the grounding pin from the power plug. If the
power plug doesn’t fit your wall outlet, ask an electrician to change the wall outlet.
• The provided power cord for the U.S. is rated at 120 V. Never connect this cord to any outlet or power supply using other
voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare an appropriate power
cord separately.
• If the power cord should be damaged, contact your dealer for replacement because it may cause fire or electric shock.
• Do not modify or alter the power cord. If the power cord is modified or altered, it may cause fire or electric shock.
• Do not overload wall outlets and extension cords as this can result in a fire or electric shock.
• In order to ensure the safety in case of trouble with the projector, use an electrical outlet having an earth leakage breaker to
supply the power to the projector. If you do not have such outlet, ask your dealer to install it.
• Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cor
• Do not plug in or out the power cord with your hand wet. It may cause electric shock.
• When you move the projector, turn off the power, unplug the power cord from the wall outlet, and then remove the connected
cords. Otherwise, the power cord may be damaged, resulting in fire or electric shock.
• If dust or metallic substance is on or around the pins of the power plug, unplug the power cord and clean it using a dry cloth.
If you continue to use the projector without cleaning, it may result in fire or electric shock. Clean the power plug periodically at
least once a year.
• Never push objects of any kind through openings of this projector as they may touch dangerous voltage points or short-out
parts that could result in a fire or electric shock.
• Never spill liquid of any kind on the projector.
• Do not operate if smoke, strange noise or odor comes out of your projector. It might cause fire or electric shock. In this case,
unplug immediately and contact your dealer.
• This projector contains high voltage circuitry. An inadvertent contact may result in an electric shock. Except as specifically
explained in the User Manual do not attempt to service this product by yourself. Please contact your dealer when you want to
fix, adjust or inspect the projector.
• Do not modify this equipment. It can lead to fire or electric shock.
• Do not keep using the damaged projector. If the projector is dropped and the cabinet is damaged, unplug the projector and
contact your dealer for inspection. It may lead to fire if you keep using the damaged projector.
• Be sure to unplug the power cord from the wall outlet if the projector is fractured or deformed. Otherwise, it may result in fire
or electric shock. Ask your dealer for repair.
• Do not place a container containing water or other liquid on the projector. If water spills on or enters the projector, it may result
in fire or electric shock.
• Keep foliage plants and pets away from the projector. The temperature around the exhaust vents and that of the cabinet on the
top of the exhaust vents become high. Take special care for small children.
8 R5905597 PHXX SERIES 16/10/2013

1. Safety
To prevent projector damage

• Unplug this projector from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for
cleaning.
• Do not use this projector near water or in contact with water.
• Do not use the projector with condensation on it. It can lead to breakdown or other failure.
• Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror Devices TM in which
case there is a loss of warranty.
• Do not block the intake and exhaust vents. If they are blocked, heat may be generated inside the projector, causing deterioration
in the projector quality and fire.
• Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as high power
laser equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices TM in
which case there is a loss of warranty.
• Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For
maximum protection, repack your set as it was originally packed at the factory.
• For safety’s sake, refrain from setting the projector at any place subjected to high temperature and high humidity. Please
maintain an operating temperature, humidity, and altitude as specified below.
- Allowable operating temperature is +41°F (+5°C) to +104°F (+40°C).
- Operating humidity: between 30% and 90%
- Be sure to use this projector at an altitude of less than 2000 meters.
2000m
• Never put any heat-producing device under the projector so that the projector does not overheat.
• Do not attach the projector to a place that is unstable or subjected to vibration.
• Do not install the projector near any equipment that produces a strong magnetic field. Also refrain from installing near the
projector any cable carrying a large current.
• Place the projector on a solid, vibration free surface; otherwise it may fall, causing serious injury to a child or adult, and serious
damage to the product.
• Do not stand upright the projector; it may fall, causing serious injury and damage to the projector.
• Slanting the projector more than ±10° (right and left) or ±15° (front and rear) may cause trouble or explosion of the lamp.
• Do not place the projector near air-conditioning unit, heater, or humidifier to avoid hot or moist air to the exhaust and ventilation
hole of the projector.
• Do not place the projector in the following places. Otherwise, a short circuit, heat generation, or melting of the power cord
coating may occur, causing fire, electric shock, product failure, or deformation.
- Outdoors or non air-conditioned place.
- Place where a gas such as a hydrogen sulfide is generated (i.e. hot spring).
- Place where there is too much salt such as near the coast.
• Do not put any object that is heavy or larger than the outer frame on the projector. Otherwise, the object may fall losing its
balance and cause injury.
• Do not subject the projector to strong shocks or vibrations. Do not handle the projector roughly. The projector may be damaged,
resulting in fire or electric shock.
• Do not replace the lamp immediately after using the projector because the lamp would be extremely hot and it may cause burns.
• Depending on the installation conditions, warm air that is emitted from the exhaust vents may flow into the intake vent, causing
the projector to display “HIGH TEMP WARNING” and then stop projecting images.
• Placing the projector directly on a carpet impairs ventilation by the fans, causing damage or failure. Put a hard board under the
projector to facilitate ventilation.
• Place the projector at least 50 cm (or 20 inches) away from the wall to prevent the intake vents and the exhaust vents that emit
hot air from being blocked.
R5905597 PHXX SERIES 16/10/2013 9

1. Safety
About batteries
• Use of a battery of wrong type may cause explosion.
• Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.
• For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and regulations
to ensure proper disposal.
• Before you dispose of the batteries, insulate them by placing insulation tape on the positive (+) and negative (-) terminals. If
you dispose of the batteries together with other conductive objects such as a metal piece, they may short out, resulting in fire
or explosion.
• Batteries may explode if misused. Do not recharge, disassemble, or heat the batteries, or put them into fire or water.
• Be sure to handle the batteries according to the instructions.
• Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.
• Keep batteries out of reach of children and pets. If children swallow the battery, see a doctor immediately.
• Remove the batteries, if the remote control is not used for a long time.
• Do not combine a new battery with an old one.
• If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your
eyes, rinse them with water and then consult your doctor.
• Do not carry or store the batteries together with metallic ballpoint pens, necklaces, coins, or hairpins. Otherwise, they may
short out, causing explosion or liquid leakage and resulting in fire or injury.
• Do not store the batteries where they are exposed to direct sunlight or subjected to high temperature and high humidity. High
temperature and high humidity may cause corrosion or liquid leakage.
On servicing
• Do not attempt to service this projector by yourself. Refer all servicing to qualified service personnel.
• Unplug this product from the wall outlet and refer servicing to qualified service technicians under the following conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
• Replacement parts: When replacement parts are required, be sure the service technician has used original replacement parts
or authorized replacement parts which have the same characteristics as the original part. Unauthorized substitutions may result
in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may void warranty.
• Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks
to determine that the product is in proper operating condition.
10 R5905597 PHXX SERIES 16/10/2013

2. Preparing the projector
2. PREPARING THE PROJECTOR

Overview
• Projector accessories
• Terminology overview
• Installation of the batteries into the remote control
• Using the remote control
• Projector configurations
• Location of ceiling mounting holes
• Screen setup
• Screen size and projection distance
• Correcting skewed or distorted image
• About fine streaks on the screen
2.1 Projector accessories

Delivered accessories
• One power cord
• One remote control
• Two R03 batteries (size AAA)
• Lens cap attached to the projector
• CD-ROM
• Safety manual
• Quick start guide
The delivered power cord has to be used exclusively for this product. Never use them for other products.
R5905597 PHXX SERIES 16/10/2013 11

2.2 Terminology overview

Remote control
2
1 6
Image 2-1
1 ON/OFF / POWER key (ON/STANDBY)

The status is changed between ON and STANDBY.
2 Transmission windows
3 Indicators
4 ▲, ►, ▼, ◄ keys
5 OK/ENTER key
6 HOME/MENU key
7 Battery compartment
Top and side projector

12 3 4 5
6 7 8 9 9 10 9
Image 2-2
1 Remote control sensor (front)

2 STATUS Led
3 Indicators (inside of the top cover)
12 R5905597 PHXX SERIES 16/10/2013

4 Intake vent/Filter cover (inside of the side cover)

5 Intake vent
6 Lens
7 Terminal panel (inside of the rear cover)
8 Remote control sensor (rear)
9 Exhaust vent
10 Lamp cover (inside of the slide cover)
Bottom side projector

1
2
Image 2-3
1 Lock bar (SECURITY ANCHOR)

Attach a chain, etc. to this lock bar to anchor the projector.
2 Adjustment feet
3 Exhaust vent
Terminal panel projector

1 2 3 4 5 6 7 8
10
9
11
12
13
Image 2-4
1 VIDEO IN terminal (BNC)

2 S-VIDEO IN terminal
3 COMPUTER/COMPONENT VIDEO IN-1 terminal (mini D-SUB 15-pin)
4 COMPUTER/COMPONENT VIDEO IN-2 terminals (R/PR, G/Y, B/PB, H/HV, V) (BNC)
R5905597 PHXX SERIES 16/10/2013 13

5 HDMI IN terminal (HDMI 19-pin)

6 COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) terminal (DVI-D 24-pin)
7 SDI IN terminal (for PHWU-81B only)
8 LAN terminal
9 REMOTE1 IN terminal (D-SUB 9-pin female)
10 SERIAL IN and OUT terminals (D-SUB 9-pin male)
11 REMOTE 2 IN and OUT terminals
Do not use these terminals.
12 Kensington Security Lock Standard connector
13 Power jack
2.3 Installation of the batteries into the remote control
Read carefully the battery safety instructions, see "Important safety instructions", page 6
Necessary parts
Two size-AAA batteries (R03).
How to insert
1. Slide and remove the rear lid of the remote control.
1
3
Image 2-5
Batteries insertion
2. Check the polarity (+), (-) of the batteries, and set them correctly, inserting their (-) side first.
Note: If the battery is inserted from the (+) side first, inserting the (-) side is difficult because the coil spring end hits on the
battery side. If the battery is forced to insert in this way, the outer label of the battery may get ripped and it may cause a
short-circuit and heating.
3. Attach the rear lid.
Replace the 2 batteries with new ones when the remote control is slow to operate.
Removing the batteries from the remote control

Slide and remove the back lid of the remote control and take out the batteries.
14 R5905597 PHXX SERIES 16/10/2013

2.4 Using the remote control

Operational range
Direct pointing
Operate the remote control within a distance of 15 m (49.2 feet) from the projector, pointing the light beam at the remote control
photo-sensor (front or rear) of the projector.
± 30° ± 30°
± 30° ± 30°
Image 2-6
Front and back control
• Keep the remote control sensor out of direct sunlight or fluorescent lamp light.
• Keep the remote control sensor at least 2 m (6 feet) away from fluorescent lamps. Otherwise, the remote control may malfunc-
tion.
• If there is an inverter-operated fluorescent lamp near the remote control, the remote control operation may become unstable.
• When you use the remote control too close to the remote control sensor, the remote control may not work correctly.
Indirect pointing
Image 2-7
You can control the projector by the remote control signals reflected on the screen. However, the remote control distance may be
restricted by the light reflection loss due to the screen characteristics.
Reception angle, vertical direction

± 20°
± 5°
± 20°
± 20°
± 20°
Image 2-8
R5905597 PHXX SERIES 16/10/2013 15

2.5 Projector configurations

Front projection
The projector is installed, either in a table mount or ceiling mount configuration, at the same side of the screen as the audience.
Image 2-9
For ceiling mounting, you need the ceiling mount kit designed for this projector. Ask a specialist for installation. For details, consult
your dealer.
Take the following things in mind for ceiling mount installations:
• The warranty on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit or instal-
lation of the ceiling mount kit in an improper location.
• When using the projector mounted on the ceiling, set IMAGE REVERSE in the INSTALLATION 1 menu to MIRROR INVERT.
• When the projector is mounted on the ceiling, images may appear darker than those projected in the case of tabletop mounting.
This isn’t a product malfunction.
• Ask your installation specialist to provide a breaker. When you do not use the projector, be sure to shut down the main power
by the breaker.
• Do not install the projector where the exhaust vents are exposed to air emitted by an air conditioning. Such installation may
cause a breakdown.
• Do not install the projector near a fire alarm because it emits hot air from its exhaust vents.
• Installation must be done by a qualified professional.
• When the projector is installed on the ceiling using the ceiling mount kit, it is recommended to hold the mount kit and the projector
using metal bars or wires in addition to the mount kit fixing screws to prevent the projector from falling due to an earthquake
or other cause. For that purpose, use metal bars, wires, or screws that bear a load of at least 260 kgf. When using metal
wires, secure one end to the adjustment foot of the projector and the other end to the mount kit. In this case, make sure that
no electrical current is flowing in the mount kit due to current leakage or other cause.
Rear projection
The projector is installed, either in a table mount or ceiling mount configuration, at the other side of the screen opposite the audience.
Image 2-10
Ask a specialist for installation. For details, consult your dealer.

Take the following in mind:
• For rear projection, set IMAGE REVERSE in the INSTALLATION 1 menu to MIRROR.
• The same points as for a front ceiling should be kept in mind during the installation.
16 R5905597 PHXX SERIES 16/10/2013

2.6 Location of ceiling mounting holes

Location
342
A
192
A
169
240
Image 2-11
A : 4 mounting holes for ceiling mount plate. (M4, depth 10 mm)
2.7 Screen setup

Environment check
Before setting up the projector, check the operating environment. If the environmental requirements are not satisfied, the projector
may break down or fail.
The allowable operating temperature is +41°F (+5°C) to +104°F (+40°C).
Setting up the screen

Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the projection angle of the
projector.
• Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of the screen
center.
• Do not install the screen where it is exposed to direct sunlight or lighting. Light directly reflecting on the screen makes the
projected images whitish and hard to view.
2.8 Screen size and projection distance

Before installation
Refer to the table to determine the screen size and projection distance.
• For the aspect ratio setting

• The figures in the tables are approximate and may be slightly different from the actual measurements.
• The lens shift height and width show distances from the factory default position.
• “L” shows the distance between the screen and the lens. • For the projection distance of the option lenses, see the tables in
appendix.
R5905597 PHXX SERIES 16/10/2013 17

W1 W W1 W1 W W1
C
H2
H1
C
H
H0
H0
H
H1
L L
H2
L
L
A A
I II
Image 2-12
I Fornt projection
II Front projection, ceiling mounted
A Maximum projection area
C Center of the lens
For PHWU-81B, when the aspect ratio is “FULL” (Display at 1920 x 1200 pixels)
Size of projector image (16:10) Projector distance (L) Lens shift height Lens shift
width
Diagonal Width (W) Height (H) Shortest Longest Standard Movement Movement Movement
size (Wide) (Tele) (H0) distance distance distance
(H1) (H2) (W1)
inch cm inch cm inch cm inch cm inch cm inch cm inch cm inch cm inch cm
40 102 34 86 21 54 55 1.4 76 1.9 0 0 10 26 4 10 3 8

60 152 51 129 32 81 83 2.1 115 2.9 0 0 15 39 6 15 5 12
80 203 68 172 42 108 112 2.8 154 3.9 0 0 21 52 8 20 7 17
100 254 85 215 53 135 141 3.6 193 4.9 0 0 26 66 10 25 8 21
150 381 127 323 79 202 213 5.4 291 7.4 0 0 39 98 15 37 12 31
200 508 170 431 106 269 285 7.2 389 9.9 0 0 52 131 20 50 16 42
250 635 212 538 132 337 356 9.1 - - 0 0 65 164 24 62 20 52
300 732 254 646 159 404 428 10.9 - - 0 0 77 197 29 75 25 62
For PHWU-81B, when the aspect ratio is “16:9” (Display at 1920 x 1080 pixels)
width
Diagonal Width (W) Height (H) Shortest Longest Standard Movement Movement Movement
size (Wide) (Tele) (H0) distance distance distance
(H1) (H2) (W1)
inch cm inch cm inch cm inch cm inch cm inch cm inch cm inch cm inch cm
40 102 35 89 20 50 56 1.4 78 2.0 1 3 11 27 4 10 3 9

60 152 52 133 29 75 85 2.2 118 3.0 2 4 16 40 6 15 5 13
80 203 70 177 39 100 115 2.9 158 4.0 2 6 21 54 8 20 7 17
100 254 87 221 49 125 145 3.7 198 5.0 3 7 27 67 10 26 8 21
150 381 131 332 74 187 219 5.6 299 7.6 4 11 40 101 15 38 13 32
200 508 174 443 98 249 293 7.4 399 10.1 6 14 53 135 20 51 17 43
250 635 218 553 123 311 366 9.3 - - 7 18 66 168 25 64 21 53
18 R5905597 PHXX SERIES 16/10/2013

For PHWX-81B, when the aspect ratio is “FULL” (Display at 1280 x 800 pixels)
width
Diagonal Width (W) Height (H) Shortstr Longest Movement Movement Movement
size (Wide) (Tele) distance (H1) distance (H2) distance
(W1)
inch cm inch cm inch cm inch cm inch cm inch cm inch cm inch cm
40 102 34 86 21 54 58 1,5 80 2,0 10 25 5 12 3 9

60 152 51 129 32 81 88 2.2 121 3.1 15 37 7 17 5 13
80 203 68 172 42 108 118 3.0 162 4.1 19 49 9 23 7 17
100 254 85 215 53 135 148 3.8 203 5.2 24 62 11 29 9 22
150 381 127 323 79 202 224 5.7 306 7.8 36 92 17 43 13 33
200 508 170 431 106 269 299 7.6 408 10.4 49 123 23 58 17 44
250 635 212 538 132 337 375 9.5 - - 61 154 28 72 21 55
300 762 254 646 159 404 450 11.4 - - 73 185 34 86 26 65
For PHWX-81B, when the aspect ratio is “NORMAL” and 4:3 signal is displayed (Display at 1066 x
800 pixels)
width
Diagonal Width (W) Height (H) Shortest Longest Movement Movement Movement
size (Wide) (Tele) distance (H1) distance (H2) distance WA
inch cm inch cm inch cm inch cm inch cm inch cm inch cm inch cm
40 102 32 81 24 61 65 1.7 90 2.3 11 29 5 12 4 10

60 152 48 122 36 91 100 2.5 137 3.5 17 43 7 18 6 15
80 203 64 163 48 122 134 3.4 183 4.7 23 57 10 25 8 20
100 254 80 203 60 152 168 4.3 230 5.8 28 72 12 31 10 25
150 381 120 305 90 229 254 6.4 346 8.8 42 108 18 46 15 37
200 508 160 406 120 305 339 8.6 - - 57 144 24 61 19 49
250 635 200 508 150 381 425 10.8 - - 71 179 30 77 24 62
For PHXG-91B
Screen size Projector distance (L) Lens shift height Lens shift
width
(W1)
inch cm inch cm inch cm inch m inch m inch cm inch cm inch cm
40 102 32 81 24 61 54 1.4 74 1.9 12 30 2 6 3 8

60 152 48 122 36 91 82 2.1 112 2.8 18 46 3 9 5 12
80 203 64 163 48 122 110 2.8 150 3.8 24 61 4 11 6 16
100 254 80 203 60 152 138 3.5 189 4.8 30 76 6 14 8 20
150 381 120 305 90 229 208 5.3 284 7.2 45 114 8 21 12 30
200 508 160 406 120 305 279 7.1 380 9.7 60 152 11 28 16 41
250 635 200 508 150 381 349 8.9 - - 75 191 14 36 20 51
300 762 240 610 180 457 419 10.6 - - 90 229 17 43 24 61
R5905597 PHXX SERIES 16/10/2013 19

2.9 Correcting skewed or distorted image

Problem
For the best projection, project images on a flat screen installed at 90 degrees to the floor. If necessary, tilt the projector using the
two adjustment feet on the bottom of the projector.
S
F
Image 2-13
S Screen
F Adjustable feet
How to adjust
1. Tilt up the projector to the appropriate angle.
2. Rotate the adjustment feet for fine adjustment.
Do not transport the projector with its adjustment feet extended. Otherwise the adjustment feet may be dam-
aged.
2.10 About fine streaks on the screen

About fine streaks
Fine streaks seen on the projected image are due to interference with the screen surface and is not a malfunction. Replace the
screen or displace the focus a little.
20 R5905597 PHXX SERIES 16/10/2013

3. Connections
3. CONNECTIONS
Preparations
To get access to the connections, the covers of the projector must be removed.
CAUTION: Only authorized service personnel are allowed to remove the covers.
3.1 Removing the covers
WARNING: Make sure that the power of the projector is turned off.
Removing the side cover

1. Loosen two screws (a) on the rear and two screws (b) on the side that are securing the side cover (c) using a Phillips screwdriver.
(c)
(b)
(a)
(c)
(b)
(a)
Image 3-1
Side cover removal
2. Slide and remove the side cover towards the rear.
Removing the rear cover

1. Loosen the four screws (d) that are securing the rear cover (e) using a Phillips screwdriver.
R5905597 PHXX SERIES 16/10/2013 21

3. Connections
(d)
(e)
Image 3-2
Rear cover removal
3.2 Power connection
WARNING: In order to ensure the safety in case of trouble with the projector, use an electrical outlet having
an earth leakage breaker to supply the power to the projector. If you do not have such outlet, ask your dealer
to install it.
About the power cord

• The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your country.
• Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to the power
cord. If the power cord should be damaged, contact your dealer for replacement because it may cause fire or electric shock.
• Do not modify or alter the power cord. If the power cord is modified or altered, it may cause fire or electric shock.
How to connect
1. Plug the attached power cord into the power cord inlet of this projector (1).
2
1
Image 3-3
Power cord connection
E Earthing (grounding) terminal
2. Plug the other end of the power cord into a power outlet (2)
22 R5905597 PHXX SERIES 16/10/2013

3. Connections
Take care for the following points

• Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cord.
• Do not plug in or out the power cord with your hand wet. It may cause electric shock.
• When you move the projector, turn off the power, unplug the power cord from the wall outlet, and then remove the connected
cords. Otherwise, the power cord may be damaged, resulting in fire or electric shock.
• If dust or metallic substance is on or around the pins of the power plug, unplug the power cord and clean it using a dry cloth.
If you continue to use the projector without cleaning, it may result in fire or electric shock. Clean the power plug periodically at
least once a year.
• Be sure to unplug the power cord from the wall outlet if the projector will not be used for a long period of time. Otherwise, it
may cause fire.
3.3 Connecting the projector to a computer

Preparations
Make sure that the power of the projector and that of the computer are turned off.
When connecting the projector to a desktop computer, disconnect the computer cable that is connected to the monitor.
Analog connection to VIDEO IN-1

1. Connect one end of a commercially available computer cable to the COMPUTER/COMPONENT/VIDEO IN-1 terminal of the
projector.
1
D
2 B
C
Image 3-4
Computer connection to Video1
A Computer
B Connector to computer
C Computer cable (option)
D Connector to Video1
2. Connect the other end of the computer cable to the monitor port of the computer.
Analog connection to VIDEO IN-2

1. Connect one end of a commercially available BNC cable to the COMPUTER/COMPONENT VIDEO IN-2 terminals of the projec-
tor.
A
R/ P R G/Y B/P B H/HV V
1
D
B
2
V H/HV B/P B G/Y R/ P R
C
Image 3-5
Computer connection to Video2
A Computer
R5905597 PHXX SERIES 16/10/2013 23

3. Connections

2. Connect the other end of the BNC cable to the 5 BNC terminals of the monitor port of the computer.
Digital connection to DVI-D IN

1. Connect one end of a commercially available DVI cable to the COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) terminal of
the projector.
D 1
2 B
C
Image 3-6
Computer connection to DVI-D
A Computer
2. Connect the other end of the DVI cable to the DVI terminal of the computer
3. Turn on the power of the projector before starting the computer.
Take attention for:

• Additional devices, such as a conversion connector and an analog RGB output adapter, are required depending on the type of
the computer to be connected.
• Use of a long cable may decrease the quality of projected images.
• Images may not be projected correctly, depending on the type of the connected computer.
• When DVI-D signal is input, some signal setting menus are unavailable.
• Also read the instruction manual of the equipment to be connected.
• Contact your dealer for details of connection.
About DDC
The COMPUTER/COMPONENT VIDEO IN-1 terminal of this projector complies with the DDC1/2B standard and the COM-
PUTER/COMPONENT VIDEO DVI-D IN (HDCP) terminal complies with the DDC2B standard. When a computer supporting this
standard is connected to this terminal, the computer will automatically load the information from this projector and prepare for
output of appropriate images.
After connecting a computer supporting this standard to this terminal, plug the power cord of the projector in the wall outlet first, and
then boot up the computer.
When connecting to a notebook computer:

When the projector is connected to a notebook computer, images may not be projected in some cases. In such cases, set the
computer so that it can output signals externally. The setting procedure varies depending on the type of the computer. See the
instruction manual of your computer.
Setting of the resolution

If the resolution of the computer doesn’t match with that of the projector, projected images may be obscured. Ensure that their reso-
lutions are the same (see pages 81 to 83). For the method to change the output resolution of the computer, contact the manufacturer
of the computer.
3.4 Connecting the projector to video equipment

Preparations
Make sure that the power of the projector and that of the computer are turned off.
Connecting to a video player, etc. to the BNC terminal

1. Connect one end of a commercially available BNC cable to the VIDEO IN terminal of the projector.
24 R5905597 PHXX SERIES 16/10/2013

3. Connections
D A
C
1
E B
Image 3-7
1 BNC plug
A Video player or the like
B BNC-RXA adapter (optional)
C To video output terminal
D B?C cable (optional)
E To VIDEO IN terminal (BNC)
2. Connect the other end of the BNC cable to the video output terminal of the video equipment.
Connecting to video equipment, equipped with S-Video

1. Connect one end of a commercially available S-video cable to the S-VIDEO IN terminal of the projector.
A
B
C
1 2
D
Image 3-8
1, 2 S Video connector
A Video player or the like
B S-video cable
C To S-video output terminal
D To S-VIDEO IN terminal
2. Connect the other end of the S-video cable to the S-video output terminal of the video equipment.
Projector + DVD player or HDTV decoder

Some DVD players have an output connector for 3-line fitting (Y, CB, CR). When connecting such DVD player with this projector,
use the COMPUTER/COMPONENT VIDEO IN-2 terminals.
1
Y C B (P B ) C R (P R )
G B R 4
3
Image 3-9
1 DVD player or HDTV decoder
2 BNC-RCA connector (optional)
3 BNC cable (option)
4 Computer/Components VIDEO IN-2
• The terminal’s names Y, PB, and PR are given as examples of when a HDTV decoder is connected.
• The terminal’s names vary depending on the connected devices.
• Use BNC cables for connection.
• Image may not be projected correctly with some DVD players.
• If colors aren’t displayed correctly when the projector is connected to a high-definition video device having R, G, and B output
terminals, set COMPUTER INPUT to RGB in the SIGNAL menu.
Connecting to video equipment having a HDMI terminal or DVI-D terminal

You can project high-quality images by connecting the COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) terminal of this pro-
jector to video equipment having a HDMI output terminal or DVI-D terminal. In addition, this projector supports HDCP and is able to
receive encrypted digital video data that are output from DVD players.
R5905597 PHXX SERIES 16/10/2013 25

3. Connections
• HDCP (High-bandwidth Digital Content Protection), developed by Intel Corporation, is a method to encrypt digital video data
for the purpose of copy protection.
• HDMI (High-Definition Multimedia Interface) is fully backward compatible with computers, displays and consumer electronics
devices incorporating the DVI standards.
• This projector can be linked with video devices equipped with HDMI output terminal or DVI-D output terminal. However, with
some of them, this projector may not display any image or not operate correctly.
• If this projector doesn’t display any image or not operate correctly, see the operation manual of the video device for its connec-
tion.
• Use of a long cable may decrease the quality of projected images.
Connection (for video equipment having an HDMI terminal)

A
C
Image 3-10
A Equipment having a HDMI terminal
B HDMI cable (option)
C HDMI IN
• Use a commercially available HDMI (with HDMI logo) cable.

• Some cables may not be connected correctly depending on the size and shape of their connectors.
• When HDMI is selected as the input source, settings of FINE SYNC., TRACKING, HOLD, etc. are unavailable.
Connection (for video equipment having a DVI-D terminal)

A
C
Image 3-11
A Equipment having a DVI-D terminal
B To DVI-D terminal
C DVI cable (option)
D Computer/Component VIDEO DVI-D IN (HDCP)
• For connection to the DVI-D terminal, use a commercially available DVI cable.
• Some cables may not be connected correctly depending on the size and shape of their connectors.
• When DVI is selected as the input source, settings of FINE SYNC., TRACKING, HOLD, etc. are unavailable.
Attention when connecting a digital device

When you connect this projector and a digital device (such as a DVD player) via the HDMI IN or COMPUTER/ COMPONENT VIDEO
DVI-D IN (HDCP) terminal, black color may appear dark and deep, depending on the type of the connected device.
• This depends on the black level setting of the connected device. There are 2 kinds of methods to digitally transfer image data,
in which different black level settings are employed respectively. Therefore, the specifications of the signals output from DVD
players differ, depending on the type of the digital data transfer method they use.
• Some DVD players are provided with a function to switch the methods to output digital signals. When your DVD player is
provided with such function, set it as follows.
EXPAND or ENHANCED → NORMAL
See the users guide of your digital device.
When your digital device does not have such function, set INPUT LEVEL to ENHANCED in the ADVANCED menu of the IMAGE
menu of the ADVANCED menu of this projector, or adjust the black color by viewing the image.
26 R5905597 PHXX SERIES 16/10/2013

3. Connections
3.5 Installing the covers

Installing the rear cover
1. Insert the rear cover (e) into the projector and tighten four screws (d) on the rear cover using a Phillips screwdriver.
(d)
(e)
Image 3-12
Rear cover mounting
Installing the side cover

1. Insert the side cover into the projector and tighten two screws (a) on the rear and two screws (b) on the side of the side cover
(c) using a Phillips screwdriver
(c)
(b)
(a)
(c)
(b)
(a)
Image 3-13
Side cove mounting
R5905597 PHXX SERIES 16/10/2013 27

3. Connections
28 R5905597 PHXX SERIES 16/10/2013

4. Getting started
4. GETTING STARTED
4.1 Basic Remote control, indications

Overview
Image 4-1
ON/OFF
HOME
OK
ARROW RIGHT (►)
ARROW UP (▲)
ARROW LEFT (◄)
ARROW DOWN (▼)
LED INDICATION
BATTERY COMPARTMENT
IR LEDs
R5905597 PHXX SERIES 16/10/2013 29

4. Getting started
Basic actions
Result RCU Lite:
action
start the projector press on/off
turn off the projector press on/off

>
show main menu on screen press home
move through menu press arrow keys
select button press ok
select and return to previous menu press ok
return to previous menu without selecting press home
clear OSD Lite of screen press home
4.2 OSD Lite navigation results

Overview
Image 4-2 Image 4-3
Basic OSD Lite navigation result RCU Lite OSD Lite on screen
action
show main menu of OSD Lite on press home main menu appears in bottom right corner
screen
to move through the OSD Lite use arrow keys button will turn red when the function is available
go to desired function press ok the menu of the desired function will appear
leave the menu or clear the screen press home the main menu will be displayed or when you are in
the main menu the screen will be cleared.
30 R5905597 PHXX SERIES 16/10/2013

4. Getting started
Hotkey / Short Cut RCU Lite → OSD Lite

Remote Command
result action → on screen
to quick adjust a burry
screen
> >
mute picture and sound
on the projector >
unmute picture and press any key
sound on the projector
main menu is on screen, go to button required RCU Lite → OSD Lite

result Action → on screen
select input manually >
>
go to input desired (default setting = HDMI)
make the image brighter or >
darker
use arrow keys to slide
default
setting = middle
adapt the contrast between >
light/dark areas
use arrow keys to slide
default
setting = middle
select color preset most fitted >
for your image
optimized setting for input signal (= default setting)
best condition to view “computer” images
best option to view movie
100% bright
aspect ratio >
>
go to aspect ratio desired (default setting =
NATIVE)
adjust focus of image >
and/or
adjust size of image >
and/or
adjust position of image >
R5905597 PHXX SERIES 16/10/2013 31

4. Getting started
main menu is on screen, go to button required RCU Lite → OSD Lite

result Action → on screen
adjust keystone >
and/or
and/or
select language >
>
go to lamp mode desired (default setting =
NORMAL
show lamp info >
show lamp mode >

and/or go to lamp mode desired (default setting
> = NORMAL
show projector info >
enter advanced menu contact your service technician to enter the advanced menu >
> default password : ◄ ◄ ► ▼
4.3 Projecting images

Preparation
Remove the lens cap before starting projecting images.
, , ,
3
2 4
1
Image 4-4
1 Status LED
2 ON/OFF key
3 OK key
4 HOME key
How to project
1. Confirm the STATUS Led lights up red.
If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the ON/OFF
key may not work after the power cord is plugged. After the fan stops rotating, press the ON/ OFF key to turn back on the STATUS
Led.
2. Turn on the power of the connected equipment.
3. Press the ON/OFF key.
32 R5905597 PHXX SERIES 16/10/2013

4. Getting started
- It may take about 2 minutes for the lamp to light up.

- The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
- After the ON/OFF key is pressed, the image may flicker before the lamp becomes stable. This is not a product malfunction.
- The lamp operation becomes stable in 2 minutes after the power is turned on and then the lamp mode selected in the menu
is activated. During the activation, displayed images may be disturbed.
- The projector starts warming up when the ON/OFF key is pressed. During the warm-up process, images may appear dark
and no commands are accepted.
- Do not cover the lens with the lens cap while the lamp is on.
4. Press the HOME key to display the OSD Lite menu and press the ▲, ►, ▼,or ◄ key to select LENS FOCUS, and press the OK
key.
The LENS FOCUS menu appears.
5. Adjust with the ◄ or ► key to get a fine picture.
6. Select an input source.
- Press the HOME key to display the OSD Lite menu and press the OK key. The INPUT menu is displayed. Then press the ▲,
►, ▼,or ◄ key to select the appropriate input source.
- The projector automatically selects the appropriate signal format. The selected signal format is displayed on the screen.
- Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such
symptom is not a malfunction.
- For computer images: Images may not be projected in the correct position, depending on the type of the input signal. In such
a case, use the AUTO POSITION function.
- When VGA (COMPUTER 1) or 5BNC (COMPUTER 2) is chosen as the source, images supplied from the computer may
flicker. Use FINE SYNC. in the SIGNAL menu to reduce flicker, if it occurs. (Fine adjustment)
- Some images become easier to view when the setting of aspect ratio is changed.
7. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified
sizes.
8. Adjust the position of the projector so that the projector and the screen are perpendicular to each other.
When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle.
9. Press the HOME key to display the OSD Lite menu and press the ▲, ►, ▼,or ◄ key to select LENS ZOOM, and press the OK
key.
The LENS ZOOM menu appears.
10.Adjust with the ▲ or ▼ key to get an approximate size.
11. Press the OK key to display the LENS SHIFT menu.
12.Press the ▲ or ▼ key to adjust the vertical position and ◄ or ► key to adjust the horizontal position of the displayed image.
When the image is not displayed within the screen, adjust the projection angle. In addition, perform the keystone adjustment, if
necessary.
13.Repeat steps 4, 5 and 9 to 12, if necessary.
Focus, zoom and lens shift adjustment is possible in the normal picture mode only.
4.4 Stop projecting images

How to stop
1. Press the ON/OFF key.
- A confirmation message is displayed.
- To cancel the procedure, press any key except the ON/OFF key.
2. Press the ON/OFF key again.
The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS Led blinks red.
3. Wait about 2 and a half minutes for the STATUS Led to be turned on.
- During this period of 2 and a half minutes in the standby mode, the intake fan and exhaust fan rotate to cool the lamp.
- The air outlet fans rotate faster as the temperature around the projector rises.
- Though the fans make loud sounds during cooling, such symptom is not a malfunction.
4. Unplug the power cord from the outlet.
R5905597 PHXX SERIES 16/10/2013 33

4. Getting started
- The STATUS Led will go out.

- If the power cord should be unplugged accidentally while either the air inlet fan or the air outlet fans are operating or the lamp
is on, allow the projector to cool down for 10 minutes with the power off. To light the lamp again, press the ON/OFF key. If the
lamp doesn’t light up immediately, press the ON/OFF key a few minutes later. If it should still fail to light up, replace the lamp.
- Cover the lens with the lens cap to protect it from dust.
Direct Power OFF

You can turn off this projector just by unplugging the power cord without pressing the ON/OFF key.
• Don’t shut down the projector while the STATUS Led is blinking after the lamp lights up because the lamp’s life may be short-
ened.
• Don’t turn the projector back on right after shutting it down because the lamp’s life may be shortened. (Wait about 10 minutes
before turning the projector back on.)
• Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without closing the menu,
the setting data of the menu may not be saved.
• Don’t shut down the projector while the filter is rolling.
4.5 Adjusting the position of the projected image

What can be done?
If the projected image is out of the screen after the adjustment, adjust the projector position or the lens position using the lens shift
function.
How to adjust
1. Press the OK key to display the LENS FOCUS/ LENS ZOOM menu.
Image 4-5
2. Adjust with the ◄ or ► key to get a fine picture.

3. Adjust with the ▲ or ▼ key to get an approximate size.
4. Press the OK key.
The LENS SHIFT menu appears.
Image 4-6
5. Press the ▲, ◄, ▼ or ► key to move the image position.
34 R5905597 PHXX SERIES 16/10/2013

4. Getting started
- When the ▼ key is pressed, the image moves down.

- When the ▲ key is pressed, the image moves up.
- When the ► key is pressed, the image moves to the right.
- When the ◄ key is pressed, the image moves to the left.
Be careful not to be caught in the opening in the lens while the lens is moving.
While the lens shift is working, the screen may flicker.
4.6 When the projected image is distorted or a trapezoid

When keystone distortion
When the screen and the projector are not placed perpendicularly to each other, projected images become trapezoidal. If you cannot
place them perpendicularly to each other, use the KEYSTONE mode adjustment.
How to adjust
1. Press the HOME key to display the OSD Lite menu.
Image 4-7
2. Select KEYSTONE by pressing the ▲, ◄, ▼ or ► key.
Image 4-8
3. Press the OK key.

The KEYSTONE menu appears.
R5905597 PHXX SERIES 16/10/2013 35

4. Getting started
Image 4-9
4. Adjust the keystone by pressing the ▲, ◄, ▼ or ► key.

In the following cases (for front projection):
Image 4-10
5. Press the ON/OFF, OK or HOME key to exit the menu.
Important
• For proper KEYSTONE-mode adjustment results, reset the lens to the factory-adjusted position using LENS SHIFT RESET in
the INSTALLATION 1 menu in the ADVANCED menu before carrying out KEYSTONE-mode adjustment.
• When the KEYSTONE-mode adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight lines
may bend in images with complicated patterns. They are not due to product malfunctions.
• When the KEYSTONE-mode adjustment is performed, the displayed image may be distorted.
• Depending on the installation conditions of the projector and the screen, a perfect rectangular image and the proper aspect
ratio may not be obtained. Slight distortion can be corrected by the CORNERSTONE-mode adjustment.
• Noise may appear on the screen during the KEYSTONE-mode adjustment because of the type of the video signal being pro-
jected and the setting values of the KEYSTONE-mode adjustment. In such cases, set the KEYSTONE-mode adjustment values
in the range where the image is displayed without noise.
• When you carry out the KEYSTONE-mode adjustment and the CURVED-mode adjustment in combination, the adjustment
range becomes narrower than that in the case where you carry out these adjustments individually. When setting the KEY-
STONE-mode adjustment value to 11 or larger, you cannot use the CURVED-mode adjustment.
• When carrying out the KEYSTONE-mode adjustment while the option lens is in use, you may not be able to obtain a perfectly
rectangular image or the correct aspect ratio. Slight distortion can be corrected by the CORNERSTONE-mode adjustment.
4.7 Blanking the screen temporarily

About blanking temporarily
The video signal is temporarily muted. The screen turns black. You will hear a mechanical shutter sound inside the projector.
How to set the BLANK mode

1. Press the ▲ key on the remote control twice while the menu is not displayed.
36 R5905597 PHXX SERIES 16/10/2013

4. Getting started
The MUTE screen appears. “MUTE ON - PRESS ANY KEY TO EXIT” is displayed for 3 seconds. Then, the mechanical shutter
is closed and the projector goes into the BLANK mode.
2. To cancel the BLANK mode, press any key on the remote control.
4.8 Auto position mode

Act as follow
When the image supplied from the computer is displaced, carry out the following procedure.
1. Project a bright image containing as many texts and characters as possible.
2. When the screen saver has been enabled, disable it.
3. Press the HOME key to display the OSD Lite menu and press the OK key.
The INPUT menu is displayed.
4. Press the ▲, ◄, ▼ or ► key to select AUTO POSITION.
Image 4-11
The projector automatically makes optimum positional settings for the input signal.
5. If the projected image is still displaced even after carrying out the AUTO POSITION several times, refer to the procedure to adjust
computer images.
6. When you carry out this procedure with a dark image, the image may be displaced.
R5905597 PHXX SERIES 16/10/2013 37

4. Getting started
38 R5905597 PHXX SERIES 16/10/2013

5. Advanced menu
5. ADVANCED MENU
5.1 Starting the advanced menus

How to set
1. Press HOME key to display the OSD Lite menu.
Image 5-1
2. Use the arrow keys to select ADVANCED and press OK.

The enter password menu is displayed.
Image 5-2
3. Enter the pass code.

Default password : ◄ ◄ ► ▼
The menu selection bar is displayed.
IMAGE MULTI- FEATURE SIGNAL NETWORK

INSTALL1 INSTALL2 SCREEN INFO
Image 5-3
Selectable menus are displayed (The menu being selected is displayed on a blue background.)
4. Press the ◄ or ► key to select a menu to use.
5. Press the OK key (or ▼ key).
R5905597 PHXX SERIES 16/10/2013 39

5. Advanced menu
The selected menu is displayed.

COLOR ENHANCER AUTO
SUPER RESOLUTION ON
CONTRAST 0
BRIGHTNESS 0
COLOR MATRIX COMPUTER
COLOR TEMP. STANDARD
COLOR 0
TINT 0
SHARPNESS 0
ADVANCED MENU ENTER
Image 5-4
The item being selected is displayed in red letters.

6. Press the ▲ or ▼ key to select an item to adjust.
7. Set the selected item by pressing the ◄ or ► key.
8. To cancel the menu, press the HOME key several times.
Important
• When an item marked with “ ” is selected, pressing the ENTER key makes its value effective or displays another screen for
further setting.
• When the HOME key doesn’t function, unplug the power cord from the wall outlet. Wait about 10 minutes, plug the power cord
in, and try again.
• The menus and screens shown in this manual may be different from those of the actual projector.
5.2 Advanced menus overview

Overview
You can make various settings using the displayed menus.
Following 8 menus are displayed. (These menus show those of PHWU-81B. Some menu items are different depending on the
models.)
IMAGE menu INSTALLATION 1 menu

INSTALL1 INSTALL2 SCREEN INFO MULTI- FEATURE SIGNAL NETWORK
IMAGE INSTALL1 INSTALL2 SCREEN INFO
COLOR ENHANCER AUTO LAMP MODE STANDARD
SUPER RESOLUTION ON LAMP SELECT DUAL
CONTRAST 0 LAMP RELAY 1H/24H
BRIGHTNESS 0 STANDBY MODE LOW
COLOR MATRIX COMPUTER IMAGE REVERSE OFF
COLOR TEMP. STANDARD HIGH ALTITUDE MODE STANDARD
COLOR 0 LENS LOCK ENTER
TINT 0 GEOMETRY ENTER
SHARPNESS 0 TEST PATTERN ENTER
ADVANCED MENU ENTER SPLIT ENTER

Image 5-5 AUTO POSITION ENTER
Image 5-6
40 R5905597 PHXX SERIES 16/10/2013

5. Advanced menu
INSTALLATION 2 menu MULTI-SCREEN menu

INSTALL1 INSTALL2 SCREEN INFO IMAGE MULTI- FEATURE SIGNAL NETWORK
AUTO POWER ON OFF EDGE BLENDING OFF
AUTO POWER OFF 5min SETTING EDGE ADJUST
SCREEN 16:10 COLOR MATCHING OFF
IMAGE CAPTURE SETUP MANUAL SETTING
SPLASH SCREEN ON MEASURE MEASURED DATA
BACK COLOR IMAGE Image 5-8
DVI LONG CABLE AUTO
REMOTE 1 MODE ENTER
FILTER MENU ENTER
Image 5-7
FEATURE menu SIGNAL menu

PROJECTOR ID ALL MEMORY CALL AUTO
GROUP ID A SIGNAL MEMORY MEMORIZE

RESOLUTION
PASSWORD FUNCTION DISPLAY INPUT (MEMORIZE ) 1024 x 768
MENU POSITION 1. HORIZ. POSITION 0
CINEMA MODE AUTO VERT. POSITION 0
LANGUAGE English FINE SYNC. 0
ADVANCED MENU ENTER TRACKING 0
RESET ALL OK COMPUTER INPUT AUTO
Image 5-9 OVER SCAN 100%
HOLD ON
ASPECT NORMAL
USER ENTER
Image 5-10
NETWORK menu INFORMATION menu

PROJECTOR NAME LAMP 1 TIME (LOW) ****H

NETWORK
CERTIFICATION OFF LAMP 2 TIME (LOW) ****H
NETWORK
ENTER NEXT LAMP RELAY
PASSWORD *D **H
IP CONFIG ENTER FILTER TIME
*****H
CONTROL SYSTEM STANDARD SERIAL NUMBER
********...
NETWORK RESET OK INPUT COMPUTER1
NETWORK RESTART OK RESOLUTION 1024 x 768
Image 5-11 VERTICAL

FREQUENCY 60.00 Hz
HORIZONTAL
FREQUENCY 48.36 kHz
SYNC. TYPE 5 WIRE
Image 5-12
R5905597 PHXX SERIES 16/10/2013 41

5. Advanced menu
5.3 Image menu

Overview
MULTI- FEATURE SIGNAL NETWORK IMAGE MULTI- FEATURE SIGNAL NETWORK
COLOR ENHANCER AUTO ADVANCED MENU

SUPER RESOLUTION ON NOISE REDUCTION OFF
CONTRAST 0 CTI OFF
BRIGHTNESS 0 INPUT LEVEL 0
COLOR MATRIX COMPUTER CLOSED CAPTION OFF
COLOR TEMP. STANDARD DEMO MODE ALL
COLOR 0
TINT 0
SHARPNESS 0
ADVANCED MENU ENTER
Image 5-13
Item Setting Function

COLOR ENHANCER AUTO Select to optimize the settings automatically depending on the input
signal. (Select this option for normal use.)
PRESENTATION Select to make the displayed image look bright and crisp.
STANDARD Select to make the displayed image look natural.
THEATER This option, suitable for viewing movies, makes the displayed image
look soft and smooth.
sRGB Select to give priority to the color reproducibility.
CLEAR BASE Select to obtain the color close to that of the X-ray film (clear base).
BLUE BASE Select to obtain the color close to that of the X-ray film (blue base).
USER Select to set the gamma curve, BrilliantColor™ or dynamic contrast.
MULTI-SCREEN You can set the gamma curve and BrilliantColor™ in the multi-screen
application.
SUPER RESOLUTION ON / OFF Use to emphasize the fineness of the image.
CONTRAST ±20 Use to adjust the contrast of the projected image.
BRIGHTNESS ±20 Use to adjust the brightness of the projected image.
COLOR MATRIX COMPUTER / VIDEO Use to adjust the predetermined tone of each color.
FLAT Use to disable COLOR MATRIX
USER Use to emphasize only certain colors or to correct the tonal deviation
of only certain colors.
COLOR TEMP. STANDARD / LOW / HIGH Select from the predetermined color temperatures.
USER Use to adjust the color temperature to a desired value.
COLOR ±10 Use to adjust the color thickness of the projected image.
TINT ±10 Use to adjust the color tint of the projected image.
SHARPNESS ±5 Use to adjust the sharpness of the projected image.
ADVANCED MENU ENTER The ADVANCED MENU is displayed for the following settings.
NOISE REDUCTION ON / OFF Use to reduce noise and roughness in the image when noisy video
signal is input.
42 R5905597 PHXX SERIES 16/10/2013

5. Advanced menu

CTI ON / OFF Use to correct smeared color boundaries.
INPUT LEVEL ±5 For analog signal input:

The input level of video signal differs among devices to be connected.
High input level causes solid white in displayed image and low input
level causes displayed image to get dark. Use this menu to adjust the
input level of analog video signal.
AUTO / ENHANCED / For digital signal input:
NORMAL
AUTO: The proper setting is automatically selected. (Selectable only
when HDMI signal is input.)
ENHANCED: Select when solid black occurs.
NORMAL: Select when grayish black occurs.
CLOSED CAPTION OFF Does not display captions.
CC1 / CC2 Displays captions.
DEMO MODE ALL Use to demonstrate the effect of SUPER RESOLUTION, COLOR
MATRIX, and DYNAMIC CONTRAST.
DYNAMIC CONTRAST Use to demonstrate the effect of DYNAMIC CONTRAST.
SUPER RESOLUTION Use to demonstrate the effect of SUPER RESOLUTION.
COLOR MATRIX Use to demonstrate the effect of COLOR MATRIX.
• When COLOR ENHANCER is sRGB, CLEAR BASE or BLUE BASE, COLOR TEMP., COLOR, TINT and COLOR MATRIX
can’t be adjusted.
• You can set MULTI-SCREEN in the COLOR ENHANCER menu only when EDGE BLENDING is ON or COLOR MATCHING is
MANUAL or MEASURE. In this case, you cannot set any other items than MULTI-SCREEN.
• This product is not in compliance with DICOM Part 14. Do not use this product for actual medical diagnosis.
• When the setting of COLOR ENHANCER is changed, the displayed image may be disturbed.
• The effect obtained when SUPER RESOLUTION is ON varies depending on the type and resolution of the input image. In
addition, the vertical line of the colored characters may be blurred.
• When the COMPUTER1, COMPUTER2, DVI, HDMI or SDI (for PHWU-81B only) is selected as the input source, COLOR and
TINT can’t be adjusted.
• TINT is available only when the NTSC signal is input.
• INPUT LEVEL is unavailable when the digital signal is supplied from the YCBCR/YPBPR terminal of the connected device.
• Captions are not displayed while information about the menu or input signal selection is being displayed on the screen.
• The closed caption function displays text information included in the NTSC signal, which is mainly used for TV broadcasting in
North America.
R5905597 PHXX SERIES 16/10/2013 43

5. Advanced menu
5.4 Installation 1 menu

Overview
MULTI- FEATURE SIGNAL NETWORK IMAGE MULTI- FEATURE SIGNAL NETWORK
LAMP MODE STANDARD LENS LOCK

LAMP SELECT DUAL ZOOM/FOCUS LOCK OFF
LAMP RELAY 1H/24H LENS SHIFT LOCK OFF
STANDBY MODE LOW LENS SHIFT RESET OK
IMAGE REVERSE OFF
HIGH ALTITUDE MODE STANDARD
LENS LOCK ENTER
GEOMETRY ENTER
TEST PATTERN ENTER
SPLIT ENTER
AUTO POSITION ENTER
Image 5-14

LAMP MODE STANDARD Select to optimize the settings automatically depending on the input
signal. (Select this option for normal use.)
LOW Select to moderate the intensity of the lamp. The operating sound is
reduced and the lamp lifetime becomes longer.
LAMP SELECT DUAL LAMP 1 and LAMP 2 illuminate.
SINGLE The lamp with shorter operation time is automatically selected at

power‑on.
LAMP 1 LAMP 1 illuminates. (When it is broken or dead, LAMP 2 illuminates
automatically.)
LAMP 2 LAMP 2 illuminates. (When it is broken or dead, LAMP 1 illuminates
automatically.)
LAMP RELAY DUAL: OFF The LAMP RELAY doesn’t work.
DUAL: 1H/24H / 2H/1W Use to set the lamp relay interval.
SINGLE: OFF The LAMP RELAY doesn’t work.
SINGLE: 24H / 1 WEEK Use to set the lamp relay interval.
STANDBY MODE STANDARD Select this option when you control the projector via the LAN,
REMOTE 1 IN, and SERIAL OUT terminal during power standby.
LOW Select this option when you don’t control the projector via the LAN,
REMOTE 1 IN, and SERIAL OUT terminal during power standby. This
option disables the LAN, REMOTE 1 IN, and SERIAL OUT terminal
and reduces the power consumption during the power standby.
IMAGE REVERSE OFF Select when viewing images from the front with the projector installed
on the floor.
MIRROR Select when viewing images projected from the behind of the screen
with the projector installed on the floor.
INVERT Select when viewing images projected from the behind of the screen
with the projector installed on the ceiling.
MIRROR INVERT Select when viewing images from the front with the projector installed
on the ceiling.
HIGH ALTITUDE MODE STANDARD This projector does not support this function.
LENS LOCK ENTER The LENS LOCK menu is displayed for the following settings.
ZOOM/FOCUS LOCK ON / OFF Use to enable or cancel the FOCUS LOCK and ZOOM LOCK.
LENS SHIFT LOCK ON / OFF Use to enable or cancel the LENS SHIFT LOCK.
LENS SHIFT RESET OK Use to reset the position of the lens to the factory setting.
44 R5905597 PHXX SERIES 16/10/2013

5. Advanced menu

GEOMETRY ENTER The geometry adjustment menu is displayed.
TEST PATTERN ENTER The test pattern is displayed.
SPLIT (for PHWU-81B/ ENTER The split screen is displayed.

PHWX-81B only)
PIP (for PHXG-91B only) ENTER The picture-in-picture (PIP) screen is displayed.
AUTO POSITION ENTER The auto position function is activated.
• Regardless of the setting of LAMP MODE, the STANDARD lamp mode is activated by default whenever the projector is turned
on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 2 minutes after turn-on.
• When the ambient operating temperature is high, the brightness of the lamp isn’t changed by switching the lamp mode.
• When the lamp mode is switched, the projected image may flicker.
• Frequent switching of the lamp mode may damage the lamp.
• When using the projector for a long time, set LAMP RELAY.
• While the lamps are being warmed up, an icon is displayed to the right of the INSTALLATION 1 menu bar. While the icon
is being displayed, you cannot set LAMP SELECT and LAMP RELAY. And an icon is displayed while the operating ambient
temperature is high. While the icon is being displayed, the lamp may not brighten even when you change the LAMP MODE to
STANDARD.
• After you switch the lamps and the newly selected lamp turns on, you cannot turn off the projector for approx. 1 minute.
5.5 Installation 2 menu

Overview
AUTO POWER ON OFF
AUTO POWER OFF 5min
SCREEN 16:10
IMAGE CAPTURE SETUP
SPLASH SCREEN ON
BACK COLOR IMAGE
DVI LONG CABLE AUTO
REMOTE 1 MODE ENTER
FILTER MENU ENTER
Image 5-15

AUTO POWER ON ON / OFF When ON is chosen, the projector is automatically turn on when the
power cord is plugged in the wall outlet. Choose ON when using the
projector mounted on the ceiling.
→ The projector is in the stand-by mode when the lamp is off. Use the
remote control to turn on the lamp.
AUTO POWER OFF OFF / 5min-8hour When no video signal is input and no operation is made, the projector
automatically turns off after the selected time period. A dialog is
displayed 5 minutes before the projector turns off.
SCREEN 16:10 (For PHWU- Select this setting when using a 16:10 screen.
81B/PHWX-81B only)
16:9 Select this setting when using a 16:9 screen.
4:3 Select this setting when using a 4:3 screen.
IMAGE CAPTURE SETUP This projector does not support this function.
SPLASH SCREEN ON Fixed to ON.
BACK COLOR BLUE / BLACK / IMAGE Use to select the background from among BLUE, BLACK and IMAGE,
which will be displayed when there is no signal input from the source.
When IMAGE is selected, the splash image will be displayed.
R5905597 PHXX SERIES 16/10/2013 45

5. Advanced menu

DVI LONG CABLE AUTO Select this option for normal use.
MANUAL Use to adjust the amount of transmission signal correction when a

long DVI cable is used.
REMOTE 1 MODE ENTER Select when controlling the projector by a control panel connected to
the REMOTE 1 IN terminal.
PIN 1 GND Unchangeable. (Fixed.)
PIN 2 POWER / NONE Select POWER or NONE.
PIN 3 COMPUTER 1 You can assign COMPUTER 1, COMPUTER 2, VIDEO, S-VIDEO,

DVI, HDMI, SDI (for PHWU-81B only), or NONE to each pin. Though
PIN 4 COMPUTER 2 the assignment can be duplicated, the pins so assigned become
invalid and their settings are displayed with asterisks at both ends
PIN 5 VIDEO (like “*COMPUTER 1*”).
PIN 6 S-VIDEO
PIN 7 DVI
PIN 8 BLANK / NONE Select BLANK or NONE.
PIN 9 ON/OFF Unchangeable. (Fixed.)
RESET OK Settings are reset to the defaults.
FILTER MENU ENTER The filter menu for the following settings is displayed.
CLEANUP PERIOD 24H / 1 WEEK / OFF You can set the filter cleaning interval.
MANUAL CLEANUP OK Select this option to clean the filter immediately.
• When STANDBY MODE in the INSTALLATION 1 menu is LOW, you cannot select REMOTE 1 MODE.
5.6 Multi-Screen menu

Overview
EDGE BLENDING OFF
SETTING EDGE ADJUST
COLOR MATCHING OFF
MANUAL SETTING
MEASURE MEASURED DATA
Image 5-16

EDGE BLENDING OFF Select when using the projector alone
ON Select when using the projector to configure the multi-screen

consisting of multiple projectors.
The following settings in the SETTING become enabled to make the
overlapped area of the displayed images unnoticeable.
SETTING EDGE ADJUST Use to make the overlapped area of the screens unnoticeable in the
multi-screen application. Use this setting to select the edges to be
overlapped or to set the overlapped areas.
BLACK LEVEL In the multi-screen application, the black level in the areas where
images are overlapped will become bright. So, use this setting to
adjust the black level in non-overlapped areas.
BRIGHT UNIFORMITY Use to correct non-uniformity in the screen brightness of the single
CORRECTION projector to facilitate edge blending.
46 R5905597 PHXX SERIES 16/10/2013

5. Advanced menu
RESET Use to reset the values of EDGE ADJUST , BLACK LEVEL and
BRIGHT UNIFORMITY CORRECTION to the defaults.
COLOR MATCHING OFF Select this option when the projector is used alone.
MANUAL Select this option when adjusting colors while viewing the screen to
correct color variations among the projectors.
MEASURE Select this option when adjusting colors using a measuring instrument
to correct color variations among the projectors.
MANUAL SETTING The test signal is displayed. Make adjustment so that the color tones
of each image match among the adjoining projectors.
RESET Use to reset the value of SETTING in the MANUAL to the default.
MEASURE MEASURED DATA The test signal is displayed. Measure the brightness and chromaticity
of each image using a measuring instrument (chroma meter) and enter
the measurement values.
TARGAT DATA Use to set the target chromaticity value of each color.
RESET Use to reset the values of MEASURED DATA and TARGET DATA
in the MEASURE to the defaults.
• When EDGE BLENDING is ON or COLOR MATCHING is MANUAL or MEASURE, COLOR ENHANCER in the IMAGE menu
is set to MULTI-SCREEN. In this case, you cannot set any other items than MULTI-SCREEN.
• The edge blending function can be used with non-directional screens. If you use a directional screen, the areas where images
are overlapped seem discontinuous depending on the viewing angle.
• The target chromaticity value entered for TARGET DATA in the MEASURE menu is just for guidance. If the obtained result
doesn’t match with the colors displayed on the adjoining projectors, adjust the value while viewing the screens.
5.7 FEATURE menu

Overview
PROJECTOR ID ALL ADVANCED MENU

GROUP ID A VIDEO SIGNAL AUTO
PASSWORD FUNCTION DISPLAY INPUT SETUP AUTO
MENU POSITION 1. SCART INPUT OFF
CINEMA MODE AUTO LAMP WARNING STANDARD
LANGUAGE English HIDE OSD OFF
ADVANCED MENU ENTER LAMP 1 TIME RESET OK
RESET ALL OK LAMP 2 TIME RESET OK
FILTER TIME RESET OK
Image 5-17

PROJECTOR ID ALL This projector does not support this function.
GROUP ID A to Z Use to set the ID number for controlling multiple projectors by groups
for monitoring and control via the SERIAL terminal.
PASSWORD FUNCTION DISPLAY INPUT / Use to enable or cancel the password lock.
MENU ACCESS /
SPLASH ID SCREEN
MENU POSITION 1 (upper left) / 2 (lower Use to change the position of the menu.
right) / 3 (center)
CINEMA MODE AUTO The film mode will be automatically activated when a film source
signal is input.
Select AUTO for normal use.
When flicker occurs on the screen, frame dropping or other incorrect
display occurs, or jaggies on slanting lines are remarkable, select
either FILM or VIDEO, which improves the symptom better.
R5905597 PHXX SERIES 16/10/2013 47

5. Advanced menu

FILM Fixed to the film mode.
VIDEO The film mode will not be activated.
LANGUAGE Different languages Use to select the language used in the menus.
ADVANCED MENU ENTER The ADVANCED MENU is displayed for the following settings.
VIDEO SIGNAL AUTO / NTSC / PAL / When AUTO is selected, the appropriate video format is automatically
SECAM / 4.43NTSC / selected depending on the input signal. If the image isn’t displayed
PAL-M / PAL-N / PAL-60 correctly, select the desired video format manually.
SETUP AUTO Select to change the SETUP mode automatically.
OFF Select to make black lighter.
3.75% / 7.5% Select to make black thicker.

When 7.5% is chosen, the brightness is decreased by the setup cancel
function for the U.S. Choose OFF when the image is dark.
SCART INPUT ON / OFF Choose ON when connecting the projector with a device equipped
with the SCART terminal that can output RGB signal. SCART terminal
is used mainly in Europe. Choose OFF normally. (Available only for
the input signal from the COMPUTER/COMPONENT VIDEO IN-1
terminal.)
LAMP WARNING STANDARD When the lamp operating time exceeds 3000 hours with LAMP MODE
set to LOW, a warning dialog is displayed.
SHORT TERM When the lamp operating time exceeds 3800 hours with LAMP MODE
set to LOW, a warning dialog is displayed.
HIDE OSD OFF Select this option for normal use.
ON The auto power-off dialog, lamp warning dialog, and abnormal

temperature dialog aren’t displayed.
LAMP 1 TIME RESET OK The LAMP 1 operation time is reset to 0.
LAMP 2 TIME RESET OK The LAMP 2 operation time is reset to 0.
FILTER TIME RESET OK The filter operation time is reset to 0.
RESET ALL OK The menu settings are reset to the factory defaults (except the
LANGUAGE, PASSWORD FUNCTION, SCREEN, and NETWORK
settings).
• CINEMA MODE can be adjusted only when a TV60, TV50, 480i, 576i or 1080i signal is being displayed.
• When SCART INPUT is set to ON, normal computer signals aren’t projected.
• Use a commercially available SCART-Mini D-SUB 15-pin cable when connecting this projector with an AV device equipped with
the SCART terminal.
• Some AV devices equipped with the SCART terminal aren’t compatible with this projector.
• The RESET ALL process may take some time to complete.
• You cannot carry out RESET ALL for approx. 2 minutes after the lamp switching or the lamp relay operation.
48 R5905597 PHXX SERIES 16/10/2013

5. Advanced menu
5.8 SIGNAL menu

Overview
MEMORY CALL AUTO RESOLUTION (MEMORIZE)

VERTICAL
SIGNAL MEMORY MEMORIZE FREQUENCY 60.00 Hz
RESOLUTION HORIZONTAL
(MEMORIZE ) 1024 x 768 FREQUENCY 48.36 KHz
HORIZ. POSITION 0 HORIZ. PIXELS 1024
VERT. POSITION 0 VERT. LINES 768
FINE SYNC. 0 EXECUTE OK
TRACKING 0 CANCEL OK
COMPUTER INPUT AUTO
OVER SCAN 100%
HOLD ON
ASPECT NORMAL
USER ENTER
USER
CLAMP POSITION 1
CLAMP WIDTH 1
VERT. SYNC. AUTO
LPF OFF
SHUTTER(U) 0
SHUTTER(L) 0
SHUTTER(LS) 0
SHUTTER(RS) 0
Image 5-18

MEMORY CALL Use to select the setting of SIGNAL MEMORY already saved.
Impossible to select if no setting has been saved.
AUTO AUTO is selected by default. It optimizes the signal format
automatically depending on the type of video signal supplied from
the computer.
1-xxx - 8-xxx Use to select the SIGNAL MEMORY already saved. The memory
number relevant to the input signal is displayed. Press the ENTER
key to clear the setting already saved.
SIGNAL MEMORY MEMORIZE The settings in the SIGNAL menu can be saved. (See page 48.) Up
to 8 settings can be saved. You can select the memory number. For
example, when you save the signal setting of 720p50 to the memory
1, the memory name is displayed as 1-720p50.
When the settings are already memorized in the selected number,
the settings will be overwritten.
RESOLUTION The current resolution is displayed. To change the current setting,
(MEMORIZE ) press the ENTER key to display the RESOLUTION (MEMORIZE)
menu. The new setting can be saved to MEMORY.
VERTICAL FREQUENCY - The vertical frequency of the currently projected video signal is
displayed.
HORIZONTAL - The horizontal frequency of the currently projected video signal is
FREQUENCY displayed.
HORIZ. PIXELS 640-1920 The number of horizontal pixels of the currently projected video signal
is displayed. When you change the current setting, select EXECUTE,
and then press the ENTER key, the image is automatically adjusted
according to the resolution you set. The adjustment result can be
saved to MEMORY
VERT. LINES 350-1200 The number of vertical lines of the currently projected video signal is
displayed. When you change the current setting, select EXECUTE,
and then press the ENTER key, the image is automatically adjusted
according to the resolution you set. The adjustment result can be
saved to MEMORY
EXECUTE OK Press the ENTER key to start the automatic adjustment. At the
completion of the automatic adjustment, a message is displayed and
you can save the adjustment result to MEMORY.
R5905597 PHXX SERIES 16/10/2013 49

5. Advanced menu

CANCEL OK The process to change the current resolution is canceled and the
SIGNAL menu is displayed.
HORIZ. POSITION 0-999 Use to adjust the horizontal position of the projected image.
VERT. POSITION 0-999 Use to adjust the vertical position of the projected image.
FINE SYNC. 0-31 Use to eliminate flickering or blur, if appears, viewing the projected
image.
TRACKING 0-9999 Use to eliminate vertical wide stripes, if appears, viewing the projected
image.
COMPUTER INPUT AUTO The proper setting is automatically selected.
RGB Select this option when connecting the projector to high definition
video equipment having R, G, and B output terminals.
YCBCR/YPBPR Select this option when connecting the projector to a DVD player or
other device having Y, CB, and CR (or Y, PB, and PR) component
video output terminals.
OVER SCAN 100%-90% Use to adjust the display area of projected image.
HOLD OFF / ON Use to adjust the image when flagging occurs near the top of the
screen.
ASPECT NORMAL For PHWU-81B:
Input video signal is displayed at the max height (1200 pixels) or max
width (1920 pixels) of the panel while its aspect ratio is maintained.
→ When SCREEN is 16:9, the input video signal is displayed at the
max height (1080 pixels) or max width (1920 pixels) of the panel.
For PHWX-81B:
For PHXG-91B:
16:9 Regardless of the type of input signal, image is displayed at 16:9
aspect ratio. Select to expand squeezed (or horizontally compressed)
images such as DVD images to 16:9.
NATIVE (for PHWU- Input video signal is displayed at its original pixel size.
81B/PHWX-81B only)
FULL For PHWU-81B:
Select to project images in full size (1920 x 1200 pixels) irrespective of
type of input signal.
→ When SCREEN is 16:9, images are displayed at 1920x1080 pixels.
For PHWX-81B:
For PHXG-91B:
50 R5905597 PHXX SERIES 16/10/2013

5. Advanced menu

4:3 Regardless of the type of input signal, image is displayed at 4:3
aspect ratio.
USER Displays the detailed settings.
USER ENTER The USER menu is displayed for the following adjustments.
CLAMP POSITION 1-255 Use to correct solid white or solid black in the projected image.
CLAMP WIDTH 1-63 Use to correct solid black in the projected image.
VERT. SYNC. AUTO / OFF Use to adjust the image when its motion doesn’t run smoothly. Select
AUTO for normal use.
LPF ON / OFF Use to select whether or not to enable the LPF.
SHUTTER(U) 0-259 (for PHWU-81B) / Use to adjust the image when noise appears on the top part of the
0-142 (for PHWX-81B) / image.
0-126 (for PHXG-91B
SHUTTER(L) 0-259 (for PHWU-81B) / Use to adjust the image when noise appears on the bottom part of
0-142 (for PHWX-81B) / the image.
0-126 (for PHXG-91B)
SHUTTER(LS) 0-311 (for PHWU-81B) / Use to adjust the image when noise appears on the left half of the
SHUTTER(RS) 0-311 (for PHWU-81B) / Use to adjust the image when noise appears on the right half of the
• Though horizontal strips may appear on the enlarged projected image, such symptom is not a malfunction.
• When you change the horizontal or vertical position to a large extent, noise may appear
• The adjustable range of the vertical position varies depending on the type of the input signal. Though the image may stay in
the same position even when the setting value is changed, such symptom is not a malfunction.
• When you increase the setting value of OVER SCAN, noise may appear on the screen.
• When 16:9 is selected by SCREEN, you cannot set ASPECT to 16:9.
• When 4:3 is selected by SCREEN, you cannot set ASPECT to 4:3.
• ASPECT-USER setting supports the COMPUTER1, COMPUTER2, DVI, and HDMI terminals only. Therefore, you cannot se-
lect USER for other terminals.
You can set the IMAGE menu and the SIGNAL menu only when the signal is supplied.
5.9 NETWORK menu

Overview
PROJECTOR NAME IP CONFIG

NETWORK DHCP
CERTIFICATION OFF ON
NETWORK
PASSWORD ENTER IP ADDRESS 0. 0. 0. 0
IP CONFIG ENTER SUBNET MASK 0. 0. 0. 0
CONTROL SYSTEM STANDARD DEFAULT GATEWAY 0. 0. 0. 0
NETWORK RESET OK MAC ADDRESS
NETWORK RESTART OK SAVE SETTINGS OK
Image 5-19

PROJECTOR NAME *****... Set the name to identify the projector. Enter up to 15 characters
(alphabets or numeric characters).
R5905597 PHXX SERIES 16/10/2013 51

5. Advanced menu

NETWORK ON / OFF Select whether to enable the network certification or not. Select OFF
CERTIFICATION for normal use.
IP CONFIG ENTER Select this setting for IP Configuration.
DHCP ON Select this setting when you obtain IP CONFIG automatically by

DHCP server.
OFF Select this setting when you set IP CONFIG manually.
IP ADDRESS ***.***.***.*** Press the ENTER key to set IP ADDRESS. When DHCP is set to ON,
you cannot change this setting.
SUBNET MASK ***.***.***.*** Press the ENTER key to set SUBNET MASK. When DHCP is set to
ON, you cannot change this setting.
DEFAULT GATEWAY ***.***.***.*** Press the ENTER key to set DEFAULT GATEWAY. When DHCP is set
to ON, you cannot change this setting.
MAC ADDRESS xx-xx-xx-xx-xx-xx Displays MAC ADDRESS.
SAVE SETTINGS OK Saves the IP CONFIG settings. When the IP CONFIG is not changed,
you cannot select SAVE SETTINGS.
CONTROL SYSTEM STANDARD Select this setting when using Projector Toolset.
AMX Select when using a controller made by AMX.
CRESTRON Select this setting when using the controller or software of Crestron
Electronics, Inc.
NETWORK RESET OK Resets the Network Setting.
NETWORK RESTART OK Press the ENTER key to restart the network function.
• AMX does not support network certification. When setting CONTROL SYSTEM to AMX, set NETWORK CERTIFICATION to
OFF.
5.10 INFORMATION menu

Overview
LAMP 1 TIME (LOW) ****H

LAMP 2 TIME (LOW) ****H
NEXT LAMP RELAY
*D **H
FILTER TIME
*****H
SERIAL NUMBER
********...
INPUT COMPUTER1
RESOLUTION 1024 x 768

VERTICAL
FREQUENCY 60.00 Hz
HORIZONTAL
FREQUENCY 48.36 kHz
SYNC. TYPE 5 WIRE
Image 5-20
Item Description
LAMP 1 TIME (LOW) This item shows the lamp operation time calculated based on that the LAMP MODE of LAMP
1 is LOW.
→ When the LAMP MODE is STANDARD, this item shows a longer lamp operating time than
the actual time.
→ When the lamp operating time is 0 to 10 hours, “0H” is displayed. The lamp operating time
exceeding 10 hours is indicated by the actual hours.
→ When the lamp operating time reaches 3000 hours, the bar turns to yellow. When it reaches
3800 hours, the bar turns to red.
→ The icon displayed to the right of the bar shows the lamp status. Yellow: On, Red: End of lamp
life or error such as illumination failure, Black: Off
52 R5905597 PHXX SERIES 16/10/2013

5. Advanced menu
Item Description
LAMP 2 TIME (LOW) This item shows the lamp operation time calculated based on that the LAMP MODE of LAMP
2 is LOW.
→ When the LAMP MODE is STANDARD, this item shows a longer lamp operating time than
the actual time.
→ When the lamp operating time is 0 to 10 hours, “0H” is displayed. The lamp operating time
exceeding 10 hours is indicated by the actual hours.
→ When the lamp operating time reaches 3000 hours, the bar turns to yellow. When it reaches
3800 hours, the bar turns to red.
→ The icon displayed to the right of the bar shows the lamp status. Yellow: On, Red: End of lamp
life or error such as illumination failure, Black: Off
NEXT LAMP RELAY The next lamp relay time is displayed.
FILTER TIME The filter operation time is displayed.
SERIAL NUMBER The serial number of the projector is displayed.
INPUT Indicates the name of the terminal to which the currently projected video signal is being input.
RESOLUTION Indicates the resolution of the currently projected video signal.
VERTICAL FREQUENCY Indicates the vertical frequency of the currently projected video signal.
HORIZONTAL Indicates the horizontal frequency of the currently projected video signal.
FREQUENCY
SYNC. TYPE Indicates the type of the sync signal for the currently projected video signal.
• NEXT LAMP RELAY isn’t displayed when LAMP RELAY is OFF or LAMP SELECT is LAMP 1 or LAMP 2 in the INSTALLATION
1 menu.
R5905597 PHXX SERIES 16/10/2013 53

5. Advanced menu
54 R5905597 PHXX SERIES 16/10/2013

6. Adjustments with the ADVANCED menu
6. ADJUSTMENTS WITH THE ADVANCED MENU
6.1 To adjust the brightness (CONTRAST and BRIGHTNESS)

How to adjust
1. Display the IMAGE menu.
2. Select CONTRAST or BRIGHTNESS by pressing the ▲ or ▼ key.
3. Adjust the selected item by pressing the ◄ or ► key.
4. To cancel the menu, press the MENU key
Contrast
Select to adjust the contrast of the image. Every time the ► key is pressed, the image becomes brighter and more defined. Every
time the ◄ key is pressed, the image becomes darker and less defined.
Brightness
Every time the ► key is pressed, the image becomes brighter. Every time the ◄ key is pressed, the image becomes darker.
6.2 To adjust the color (COLOR and TINT)

how to adjust
2. Select COLOR or TINT by pressing the ▲ or ▼ key.
→ COLOR or TINT is unavailable when COMPUTER1, COMPUTER2, DVI or HDMI is selected as the input source.
→ TINT is available only when the NTSC signal is input.
4. To cancel the menu, press the MENU key.
Color
Use to adjust the color thickness of the projected image. Every time the ► key is pressed, the color becomes thicker.
Every time the ◄ key is pressed, the color becomes lighter.
Tint
Use to adjust the tint of the projected image. Every time the ► key is pressed, the image appears more greenish.
Every time the ◄ key is pressed, the image appears more reddish.
6.3 To sharpen or soften the projected image (SHARPNESS)

How to adjust
2. Select SHARPNESS by pressing the ▲ or ▼ key.
6.4 To adjust the tone of white (COLOR TEMP.)

What can be done?
A preset color temperature (white tone) can be selected or you can use a customized color temperature.
R5905597 PHXX SERIES 16/10/2013 55

How to select
2. Select COLOR TEMP. by pressing the ▲ or ▼ key.
3. Select your desired color temperature by pressing the ◄ or ► key.
To customize the color temperature

1. Select COLOR TEMP. in the IMAGE menu.
2. Press the ◄ or ► key to select USER .
3. Press the ENTER key.
4. Press the ▲ or ▼ key to select the desired item.
COLOR TEMP. –USER

CONTRAST R 0
CONTRAST G 0
CONTRAST B 0
BRIGHTNESS R 0
BRIGHTNESS G 0
BRIGHTNESS B 0
Image 6-1
5. Press the ◄ or ►key to adjust the selected item.

6. Repeat step 4 and step 5 for optimum adjustment results.
Enabling stored user color temperature

1. Set COLOR TEMP. to USER in the IMAGE menu.
About color temperature

Color temperature is a way to show the differences in white. White of which temperature is low appears reddish. When the color
temperature rises, white appears bluish. For example, you can change the color temperature using the following procedures.
To raise the color temperature: Increase the CONTRAST B (blue) and decrease the CONTRAST R (red).
To reduce the color temperature: Decrease the CONTRAST B (blue) and increase the CONTRAST R (red).
→ If you set all of CONTRAST R, G, and B to negative values, the original brightness of the image can’t be obtained even when you
maximize CONTRAST in the IMAGE menu.
6.5 Color Enhancer

With the IMAGE menu
2. Select COLOR ENHANCER by pressing the ▲ or ▼ key.
COLOR ENHANCER AUTO
Image 6-2
3. Select USER or MULTI-SCREEN by pressing the ◄ or ► key.
COLOR ENHANCER –USER COLOR ENHANCER –MULTI-SCREEN

GAMMA MODE DYNAMIC GAMMA MODE 2.0
BrilliantColor TM
10 BrilliantColor TM
0
DYNAMIC Image 6-4
CONTRAST 3
Image 6-3
Important: You can set MULTI-SCREEN only when EDGE BLENDING is ON or COLOR MATCHING is MANUAL or MEASURE
in the MULTI-SCREEN menu.
The detailed menu for the color enhancer is displayed.
56 R5905597 PHXX SERIES 16/10/2013

5. Select an item you want to set by pressing the ▲ or ▼ key.
GAMMA mode
Use this item to set the gamma optimally.
When USER is selected:
DYNAMIC Select when viewing images supplied from the computer.

NATURAL Select when viewing images supplied from the video device.
DETAIL Select when viewing images of which brightness should be kept relatively low, such as movies and music
performance.
When MULTI-SCREEN is selected:
1.8/2.0/2.2 Select the gamma characteristics from 1.8th, 2.0th, and 2.2nd power.
BrilliantColor™
Use this item to make the colors having medium brightness such as yellow and skin tone look natural. Press the ◄ key to decrease
the value to lessen the effect. Press the ► key to increase the value to heighten the effect. (BrilliantColor™ doesn’t work at value 0.)
Dynamic contrast
Use this item to sharpen the images by improving the contrast.
When you set the larger value, this function works more effective, and when you set the smaller value, it works less effective.
This function does not work when this item is set to OFF.
Select a setting value by pressing the ◄ or ► key.
→ For more enhanced color reproduction, set BrilliantColor™ to 0.
6.6 Adjusting the fineness of the image (SUPER RESOLUTION)

How to adjust
2. Select SUPER RESOLUTION by pressing the ▲ or ▼ key.
SUPER RESOLUTION ON
SUPER RESOLUTION
LEVEL 1
Image 6-5
3. Press the ◄ or ► key to select ON .

5. Make adjustment using the ◄ or ► key.
Important
When you make SUPER RESOLUTION adjustment, the colors of the menu may be obscured, but this is not a failure.
6.7 Adjusting the tone of each color (COLOR MATRIX)

How to adjust
2. Select COLOR MATRIX by pressing the ▲ or ▼key.
COLOR MATRIX COMPUTER
Image 6-6
3. Press the ◄ or ► key to select USER
R5905597 PHXX SERIES 16/10/2013 57

COLOR MATRIX −USER

BASE COMPUTER
RED 0
YELLOW 0
GREEN 0
CYAN 0
BLUE 0
MAGENTA 0
SATURATION 0
RGB-TINT 0
Image 6-7

5. Select an item you want to set using the ▲ or ▼ key.
- To set COLOR MATRIX that is used as the base, select BASE.
- If you want to adjust the saturation of all colors of the image, select SATURATION.
- If you want to adjust the balance of all colors of the image, select RGB‑TINT.
6. Press the ◄ or ► key to adjust the color balance of the selected color.
7. Repeat step 5 and step 6 for optimum adjustment results.
Note
→ When the input signal is VIDEO or COMPUTER, the items in the COLOR MATRIX-USER menu are automatically set to the
predetermined values. You can change these values manually.
→ To disable the COLOR MATRIX adjustment, select FLAT in step 3.
→ When you make COLOR MATRIX adjustment, the colors of the menu will change, but this is not a failure.
6.8 Setting the screen size

About screen size
Change the setting of the SCREEN according to the type of the screen to be used.
How to change
1. Display the INSTALLATION 2 menu.
2. Select SCREEN by pressing the ▲ or ▼ key.

AUTO POWER ON OFF
AUTO POWER OFF 5min
SCREEN 16:10
Image 6-8
3. Select your desired aspect ratio by pressing the ◄ or ► key.

You can select the aspect ratio from 16:10 (for PHWU-81B/PHWX- 81B only), 16:9, and 4:3.
6.9 Setting the aspect ratio

About aspect ratio
You can change the aspect ratio of the input video signal (or the ratio of width to height of the image). Change the setting according
to the type of the screen to be used or your preference.
How to set
1. Display the SIGNAL menu.
2. Select ASPECT by pressing the ▲ or ▼ key.
58 R5905597 PHXX SERIES 16/10/2013

3. Select your desired aspect ratio by pressing the ◄ or ► key.

- Select the aspect ratio from NORMAL, 16:9, NATIVE (for PHWU-81B/PHWX-81B only), 4:3, and FULL.
- When 16:9 is selected by SCREEN in the INSTALLATION 2 menu, 16:9 cannot be selected.
- When 4:3 is selected by SCREEN in the INSTALLATION 2 menu, 4:3 cannot be selected.
- The tables on pages 46 and 47 show the image display patterns depending on the settings.
For PHWU-81B:
When SCREEN is 16:10:
Setting NORMAL 16:9 NATIVE 4:3 FULL

Input video signal is Regardless of the Input video signal Regardless of the Regardless of the
displayed at the max type of input signal, is displayed at its type of input signal, type of input signal,
height (1200 pixels) image is displayed original pixel size. image is displayed image is displayed
or max width (1920 at 16:9 aspect (When the pixel size at 4:3 aspect ratio at the full panel size
pixels) of the panel ratio (1920 x 1080 is larger than the (1600 x 1200 pixels (1920 x 1200 pixels).
while its aspect ratio pixels). Select to panel size, only the
is maintained. expand squeezed center part of the
(or horizontally image is displayed.)
compressed)
images such as
Input signal DVD images to 16:9.
UXGA signal 4:3 16:9 4:3 4:3 16:10

1600 x 1200
(4:3) 1600 x 1200 1920 x 1080 1600 x 1200 1600 x 1200 1920 x 1200
WUXGA signal 16:10 16:9 16:10 4:3 16:10

1920 x 1200
(16:10) 1920 x 1200 1920 x 1200 1920 x 1200 1600 x 1200 1920 x 1200
1080p signal 16:9 16:9 16:9 4:3 16:10

1920 x 1080
(16:9) 1920 x 1080 1920 x 1080 1920 x 1080 1600 x 1200 1920 x 1200
• In such cases as when you keep projecting images in the narrower area than the screen for a long time and then change the
mode to FULL, the masking areas may remain as afterimage around the displayed image. Consult your dealer in this case.
• If you change the screen setting, the aspect setting is automatically changed to NORMAL. Therefore, in such a case, set the
desired aspect ratio again.
For PHWX-81B:
When SCREEN is 16:10:
Setting NORMAL 16:9 NATIVE 4:3 FULL

Input video signal is Regardless of the Input video signal Regardless of the Regardless of the
displayed at the max type of input signal, is displayed at its type of input signal, type of input signal,
height (800 pixels) image is displayed original pixel size. image is displayed image is displayed
or max width (1280 at 16:9 aspect (When the pixel size at 4:3 aspect ratio at the full panel size
pixels) of the panel ratio (1280 x 720 is larger than the (1066 x 800 pixels). (1280 x 800 pixels).
while its aspect ratio pixels). Select to panel size, only the
is maintained. expand squeezed center part of the
(or horizontally image is displayed.)
compressed)
images such as
Input signal DVD images to 16:9.
XGA signal 4:3 16:9 4:3 4:3 16:10

1024 x 768
(4:3) 1066 x 800 1280 x 720 1024 x 768 1066 x 800 1280 x 800
R5905597 PHXX SERIES 16/10/2013 59

WXGA signal 16:10 16:9 16:10 4:3 16:10

1280 x 800
(16:10) 1280 x 800 1280 x 720 1280 x 800 1066 x 800 1280 x 800
WXGA signal 16:9.6 16:9 16:9.6 4:3 16:10

1280 x 768
(16:9.6) 1280 x 768 1280 x 720 1280 x 768 1066 x 800 1280 x 800
• In such cases as when you keep projecting images in the narrower area than the screen for a long time and then change the
mode to FULL, the masking areas may remain as afterimage around the displayed image. Consult your dealer in this case.
For PHXG-91B:
When SCREEN is 4:3:
Setting NORMAL 16:9 FULL

Input video signal is displayed Regardless of the type of input Regardless of the type of input
at the max height (768 pixels) or signal, image is displayed at 16:9 signal, image is displayed at
max width (1024 pixels) of the aspect ratio (1024 x 576 pixels). the full panel size (1024 x 768
panel while its aspect ratio is Select to expand squeezed (or pixels).
maintained. horizontally compressed) images
Input signal such as DVD images to 16:9.
XGA signal 4:3 16:9 4:3

1024 x 768
(4:3) 1024 x 768 1024 x 576 1024 x 768
WXGA signal 16:10 16:9 4:3

1280 x 800
(16:10) 1024 x 640 1024 x 576 1024 x 768
1080p signal 16:9 16:9 4:3

1920 x 1080
(16:9) 1024 x 576 1024 x 576 1024 x 768
• When a 16:9 image is kept displayed for a long time before displaying FULL image, the afterimages of the black bars may
appear on the FULL image screen. Consult your dealer in this case.
6.10 Adjusting the detailed setting of ASPECT

How to adjust
2. Select ASPECT by pressing the ▲ or ▼ key.
3. Press the ◄ or ► key to select USER .
60 R5905597 PHXX SERIES 16/10/2013

ASPECT −USER
ZOOM(H) 100
ZOOM(V) 100
HORIZ. POSITION 0
VERT. POSITION 0
RASTER POSITION(H) 0
RASTER POSITION(V) 0
RESET OK
Image 6-9
ASPECT-USER setting supports the COMPUTER1, COMPUTER2, DVI, and HDMI terminals only. Therefore, you cannot select
USER for other terminals.
5. Select an item you want to set using the ▲ or ▼ key.
ZOOM(H)
The horizontal image size is adjusted using the center of the image as the base point. The setting range is 50% to 500%.
ZOOM(V)
The vertical image size is adjusted using the center of the image as the base point. The setting range is 50% to 500%.
HORIZ. POSITION
Use to adjust the horizontal position of the projected image. The setting range is -999 to +999.
VERT. POSITION
Use to adjust the vertical position of the projected image. The setting range is -999 to +999.
RASTER POSITION(H)
When the supplied image is not projected on the entire display area, the horizontal location of the projected image can be adjusted
within the area. The setting range is -960 to +960 (for PHWU-81B), -640 to +640 (for PHWX-81B), or -512 to +512 (for PHXG-91B).
RASTER POSITION(V)
When the supplied image is not projected on the entire display area, the vertical location of the projected image can be adjusted
within the area. The setting range is -540 to +540 (for PHWU-81B), -400 to +400 (for PHWX-81B), or -384 to +384 (for PHXG-91B).
RESET
Press the ENTER key to reset the USER settings.
Important
• Noise may appear on the screen depending on the combination of the type of the video signal being projected and the setting val-
ues of the ZOOM(H), ZOOM(V), HORIZ. POSITION, VERT. POSITION, RASTER POSITION(H), and RASTER POSITION(V).
In such cases, set these values in the range where the image is displayed without noise.
• The adjustable range of each setting varies depending on the type of the input signal.
6.11 Saving the setting in the SIGNAL MEMORY

What can be done?
You can save the settings of the SIGNAL menu using the SIGNAL MEMORY.
You can save multiple signal settings for one signal format and switch the method according to use. Up to 8 settings can be saved.
Example
AUTO Memory number in the SIGNAL MEMORY

1–720p50 2–720p50 3–1080i60 4–xxx ... 8–xxx
SINGAL ANY SIGNAL 720p50 720p50 1080i60 - -
menu
To save the setting in the SIGNAL MEMORY

R5905597 PHXX SERIES 16/10/2013 61

2. Select SIGNAL MEMORY while AUTO is selected in the MEMORY CALL by pressing the ▲ or ▼ key.
3. Select MEMORIZE and press the ENTER key.
4. Select your desired memory number by pressing the ◄ or ► key.
5. Press the ENTER key to save the memory.
- To save the new setting, select a new memory number. The memory number of the MEMORY CALL changes to a new one
after saving the setting.
- When the setting in the selected memory number is changed, the changed setting is automatically saved.
To select the saved memory by the MEMORY CALL

2. Select MEMORY CALL by pressing the ▲ or ▼ key.
3. Select your desired memory number by pressing the ◄ or ► key.
- Only the memory number relevant to the input signal can be selected.
- When the same signal is input on the next time, the selected memory number is still memorized.
6.12 Adjusting a computer image

How to adjust
This projector automatically selects a proper signal format according to the type of video signal supplied from the computer. However,
video signals from the computer may not be projected correctly depending on the types of the computer and images to be projected.
In such a case, make adjustment according to the flowchart below.
62 R5905597 PHXX SERIES 16/10/2013

When the size and position of

the computer image are not correct.
Pr oject a bright computer image containing as many texts and characters as possible.
Note) Disable the screen saver if it is active.
Select AUTO POSITION in the INPUT menu of the OSD Lite menu and press the OK key.
Settings are automatically and optimally adjusted for the input signal.
NO
Image is projected
correctly .
YES Display the screen resolution setting menu of your computer.

(Example: In the case of Windows® PC, right-click on the desktop, select Properties, and click the
Settings tab to display the screen resolution setting.)
The screen
resolution setting of your computer NO
is dif ferent from the setting of RESOLUTION
(MEMORIZE ) in the SIGNAL menu
of the projector.
YES
Select RESOLUTION (MEMORIZE ) in the SIGNAL menu

and press the ENTER key.
Set HORIZ. PIXELS and VERT. LINES to the values of the screen resolution of your computer.
(Example: When the screen resolution of the computer is 1280x800, set HORIZ. PIXELS to 1280 and
VER T. LINES to 800.)
Select EXECUTE and press the ENTER key.
Automatic adjustment starts according to the selected resolution.
NO
Image is projected
correctly.
YES Perform manual NO

adjustment.
After the memory saving YES When you don’ t save
message is displayed, the adjustment result,
select MEMORY and press After the memory saving press the MENU key.
the ENTER key. message is displayed,
select MEMORY and press
the ENTER key. Adjustment is canceled.
Adjust HORIZ. POSITION, VERT. POSITION, and TRACKING

in the SIGNAL menu. For details, see “Simple method to
adjust the image position.”
Adjustment is completed.
Image 6-10
6.13 How to adjust the image supplied from the computer using the menu
What to do when
Carry out the following procedures according to the symptoms.
Wide strips appear. Adjust TRACKING in the SIGNAL menu.

The projected image flickers. Adjust FINE SYNC. in the SIGNAL menu.
The projected image is blurred.
R5905597 PHXX SERIES 16/10/2013 63

The projected image is displaced horizontally. Adjust HORIZ. POSITION in the SIGNAL menu. Every time the
◄ key is pressed, the image moves to the right. Every time the
► key is pressed, the image moves to the left.
The projected image is displaced vertically. Adjust VERT. POSITION in the SIGNAL menu. Every time the
◄ key is pressed, the image moves down. Every time the ►
key is pressed, the image moves up.
The top part of the image flags. Change the setting of HOLD in the SIGNAL menu. Select
ON , press the ENTER key, and adjust BEGIN or END to
minimize the flagging.
A solid black or solid white appears in the image. Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL -
USER menu.
The motion doesn’t run smoothly. Adjust VERT. SYNC. in the SIGNAL - USER menu. Select
AUTO for normal use.
Noise appears on the right or left half of the image. Adjust SHUTTER(LS) or SHUTTER(RS) in the SIGNAL -
USER menu.
Noise appears on the top or bottom part of the image. Adjust SHUTTER(U) or SHUTTER(L) in the SIGNAL - USER
menu.
Do not change the settings of the SIGNAL menu in normal use.
How to adjust
2. Press the ▲ or ▼ key to select an item to adjust.
6.14 Simple method to adjust the image position

To adjust the horizontal position
1. Align the left edge of the image with the left side of the screen by adjusting HORIZ. POSITION. Then, align the right edge of the
image with the right side of the screen by adjusting TRACKING.
2. Repeat step 1 above to complete the adjustment of the horizontal position.
To adjust the vertical position

1. Align the upper edge of the image with the upper side of the screen by adjusting VERT. POSITION.
6.15 LPF (Progressive filter)

About LPF
You can select whether or not to enable the LPF. Vertical or horizontal streak noise may appear on the projected image, depending
on the type of the DVD player or game console you use. In such a case, you can reduce such streak noise by enabling the LPF.
However, projected images become softened slightly.
6.16 Image displayed on the multi-screen, joints

About multi-screen
You can configure a multi-screen display using multiple projectors.
You can make the joints of the images displayed on the projectors unnoticeable and adjust the differences in the brightness and the
color tint of them.
Important: Depending on the installation condition, the projected image may fluctuate due to the effect of the exhausted wind. In
such a case, open up the space between the projectors so that the image doesn’t fluctuate (approximately 70 cm or more).
You can make the joints of the images projected on the projectors unnoticeable using the menu settings.
Making the joints unnoticeable

1. Display the MULTI-SCREEN menu.
64 R5905597 PHXX SERIES 16/10/2013

2. Select EDGE BLENDING by pressing the ▲ or ▼ key.
EDGE BLENDING OFF
Image 6-11
3. Select ON by pressing the ◄ or ► key.

4. Select SETTING by pressing the ▲ or ▼ key.
SETTING EDGE ADJUST
Image 6-12
5. Select EDGE ADJUST by pressing the ◄ or ► key.
SETTING - EDGE ADJUST

EDGE SELECT UP
BLENDING OFF
START POSITION 0
WIDTH 128
MARKER OFF
Image 6-13

EDGE SELECT Select the joint you want to adjust from UP, LOW, LEFT, and RIGHT.
BLENDING When you select ON, the joint selected by EDGE SELECT becomes unnoticeable.
START Set the position to start the edge adjustment.
POSITION When UP or LOW is selected:
• 0 to 270 (for PHWU-81B)
• 0 to 192 (for PHWX-81B/PHXG-91B)
When LEFT or RIGHT is selected:
WIDTH Set the width of the overlap of the joint selected by EDGE SELECT.
When UP or LOW is selected:
When LEFT or RIGHT is selected:
The setting range of START POSITION and WIDTH vary depending on their setting values.
MARKER When you select ON, a marker for easily locating the overlap of the joint is displayed.
8. Select a setting value by pressing the ◄ or ► key.

9. Repeat step 7 and step 8, if necessary.
10.Press the MENU key once.
11. Select BLACK LEVEL by pressing the ◄ or ► key.
SETTING BLACK LEVEL
Image 6-14
12.Press the ENTER key.
SETTING - BLACK LEVEL

INTERLOCKED ON
RED 0
GREEN 0
BLUE 0
Image 6-15
13.Select an item you want to set by pressing the ▲ or ▼ key.

→ Adjust the black level in areas other than the overlapped areas.
→ When you set INTERLOCKED to ON, you can adjust RED, GREEN, and BLUE simultaneously. When you set it to OFF, you
can adjust RED, GREEN, and BLUE separately.
R5905597 PHXX SERIES 16/10/2013 65

14.Select a setting value by pressing the ◄ or ► key.

15.Repeat step 13 and step 14, if necessary.
16.Press the MENU key once.
17.Select BRIGHT UNIFORMITY CORRECTION by pressing the ◄ or ► key.
BRIGHT UNIFORMITY
SETTING CORRECTION
Image 6-16
→ When EDGE BLENDING is ON, the brightness of the projected images is made even.
18.Press the ENTER key.
The BRIGHT UNIFORMITY CORRECTION dialog box and the correction position marker are displayed.
POSITION :
SELECT : ENTER
2
Image 6-17
1 BRIGHT UNIFORMITY CORRECTION dialog box
2 Correction position marker
Every time you press the ENTER key, the BRIGHT UNIFORMITY CORRECTION dialog box shows POSITION and LEVEL al-
ternately.
POSITION Press the ▲, ▼, ◄, or ► key to move the correction position marker.

LEVEL Press the ◄, or ► key to adjust the correction amount.
19.Cancel the BRIGHT UNIFORMITY CORRECTION dialog box.

Press any key other than the ▲, ▼, ◄, or ►, and ENTER keys to clear the dialog box. Or, the dialog box disappears in 10
seconds after the last use.
20.To cancel the menu, press the MENU key.
6.17 Adjusting the color variations

How to adjust
You can adjust the variations in the colors of the images displayed on multiple projectors using the menu settings.
Adjustment while viewing the screen

2. Select COLOR MATCHING by pressing the ▲ or ▼ key.
COLOR MATCHING OFF
Image 6-18
3. Select MANUAL by pressing the ◄ or ► key.

4. Select MANUAL by pressing the ▲ or ▼ key.
MANUAL SETTING
Image 6-19
5. Select SETTING by pressing the ◄ or ► key.

66 R5905597 PHXX SERIES 16/10/2013

MANUAL – SETTING
COLOR RED
GAIN 100
SATURATION 0
HUE 0
WHITE R -- -
WHITE G -- -
WHITE B -- -
AUTO PATTERN ON
Image 6-20

Select the color you want to adjust using COLOR.
When you set AUTO PATTERN to ON, the test pattern of each color is displayed.
Adjustment using a chroma meter

2. Select COLOR MATCHING by pressing the ▲ or ▼ key.
COLOR MATCHING OFF
Image 6-21
3. Select MEASURE by pressing the ◄ or ► key.

Set now the measured brightness and the chromaticity coordinates
4. Select MEASURE by pressing the ▲ or ▼ key.
MEASURE MEASURED DATA
Image 6-22
5. Select MEASURED DATA by pressing the ◄ or ► key.

MEASURE – TARGET DATA

COLOR RED
GAIN
*. ***
x *. ***
y
*. ***
AUTO PATTERN ON
Image 6-23

→ Select the color you want to adjust using COLOR.
→ When you set AUTO PATTERN to ON, the test pattern of each color is displayed.
6.18 Resetting the settings

About reset
You can reset the SETTING, MANUAL, and MEASURE settings to the factory defaults.
How to reset
2. Select SETTING, MANUAL or MEASURE by pressing the ▲ or ▼ key.
3. Select RESET by pressing the ◄ or ► key.
R5905597 PHXX SERIES 16/10/2013 67

6.19 When the projected image is distorted

What should happen:
When the projected image is distorted, carry out any of the KEYSTONE, CORNERSTONE, and CURVED mode adjustments to
correct the distortion.
When the image distorts in a trapezoid shape, use the KEYSTONE-mode adjustment. For fine adjustment of the image shape, use
the CORNERSTONE-mode adjustment. To adjust the image projected on a curved surface, use the CURVED-mode adjustment.
Every time you press the ENTER key selecting the GEOMETRY menu, the menu switches in the order of KEYSTONE, CORNER-
STONE, CURVED, INSTALLATION 1 menu, KEYSTONE....
6.19.1 Adjust using Keystone mode
What can be done?

When the image distorts in a trapezoid shape, use the KEYSTONE-mode adjustment.
How to adjust
2. Select GEOMETRY by pressing the ▲ or ▼ key.
KEYSTONE
: 0
: 0
KEYSTONE
SELECT : MENU
Image 6-24
4. Make adjustment using the ▲, ▼, ◄, or ► key.

Every time you press the MENU key, the adjustment menu changes as follows: KEYSTONE → RESET → KEYSTONE ...
KEYSTONE menu
You can correct the distortion vertically or horizontally focusing on the screen center.
In the following cases (for front projection):
Image 6-25
When you press the ◄ or ► key in the RESET mode, the distortion correction is reset.
68 R5905597 PHXX SERIES 16/10/2013

Important
• For proper KEYSTONE-mode adjustment results, reset the lens to the factory-adjusted position using LENS SHIFT RESET in
the INSTALLATION 1 menu before carrying out KEYSTONE-mode adjustment.
• When the KEYSTONE-mode adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean a
projection angle.
• When the KEYSTONE-mode adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight lines
• When the KEYSTONE-mode adjustment is performed, the displayed image may be distorted.
• Depending on the installation conditions of the projector and the screen, a perfect rectangular image and the proper aspect
ratio may not be obtained. Slight distortion can be corrected by the CORNERSTONE-mode adjustment.
• Noise may appear on the screen during the KEYSTONE-mode adjustment because of the type of the video signal being pro-
jected and the setting values of the KEYSTONE-mode adjustment. In such cases, set the KEYSTONE-mode adjustment values
in the range where the image is displayed without noise.
range becomes narrower than that in the case where you carry out these adjustments individually. When setting the KEY-
STONE-mode adjustment value to 11 or larger, you cannot use the CURVED-mode adjustment.
• When carrying out the KEYSTONE-mode adjustment while the option lens is in use, you may not be able to obtain a perfectly
6.19.2 Adjustment using the CORNERSTONE mode
When using
Use this adjustment for fine adjustment of the image shape. You can use this adjustment for adjusting the image displayed in the
edge blending mode, too.
How adjust
2. Select GEOMETRY by pressing the ▲ or ▼key.
4. Press the ENTER key again.
The CORNERSTONE menu appears.
CORNERSTONE
: 0
: 0
LOWER RIGHT
SELECT : HOME
Image 6-26

Every time you press the MENU key, the adjustment menu changes as follows:
LOWER RIGHT → LOWER LEFT → UPPER RIGHT → UPPER LEFT → RESET → LOWER RIGHT ...
LOWER RIGHT, LOWER LEFT, UPPER RIGHT, or UPPER LEFT menu

You can adjust the horizontal or vertical position of the selected corner.
Example: Adjustment of the upper left corner position (UPPER LEFT)
Image 6-27
R5905597 PHXX SERIES 16/10/2013 69

Important
• When the CORNERSTONE-mode adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight
lines may bend in images with complicated patterns. They are not due to product malfunctions.
• When the CORNERSTONE-mode adjustment is performed, the displayed image may be distorted.
• Noise may appear on the screen during the CORNERSTONE-mode adjustment because of the type of the video signal being
projected and the setting values of the CORNERSTONE-mode adjustment. In such cases, set the CORNERSTONE-mode
adjustment values in the range where the image is displayed without noise.
• Large distortion of the image shape or aspect ratio may not be corrected by the CORNERSTONE-mode adjustment.
6.19.3 Adjustment using the CURVED mode
When using?
Use this adjustment to adjust images projected on a curved surface.
How to adjust
2. Select GEOMETRY by pressing the ▲ or ▼key.
4. Press the ENTER key twice.
The CURVED menu appears.
Every time you press the MENU key, the adjustment menu changes as follows: ARC → HORIZ. ORIGIN → VERT. ORIGIN →
RESET → ARC...
ARC menu
You can correct the arc vertically or horizontally focusing on the screen center.
Image 6-28
HORIZ. ORIGIN or VERT. ORIGIN menu

When the CURVED-mode adjustment has excessive effect on either top or bottom or either right or left side of the screen, adjust
the horizontal or vertical position of the origin to the horizontal or vertical arc. Without the arc adjustment, the image shape won’t
change.
Adjusting the origin to the horizontal arc
When the horizontal arc adjustment is negative (-) (or the ARC is adjusted in the ▼ direction)
70 R5905597 PHXX SERIES 16/10/2013

Image 6-29
When the horizontal arc adjustment is positive (+) (or the ARC is adjusted in the ▲ direction)
Image 6-30
Adjusting the origin to the vertical arc

When the vertical arc adjustment is negative (-) (or the ARC is adjusted in the ◄ direction)
Image 6-31
When the vertical arc adjustment is positive (+) (or the ARC is adjusted in the ► direction)
R5905597 PHXX SERIES 16/10/2013 71

Image 6-32
Important
• When the CURVED-mode adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight lines
• When the CURVED-mode adjustment is performed, the displayed image may be distorted.
• Depending on the installation conditions of the projector and the screen or the correction amount of the CURVED-mode adjust-
ment, you may not obtain a complete rectangular screen or the correct aspect ratio. Slight distortion can be corrected by the
CORNERSTONE-mode adjustment.
• Noise may appear on the screen during the CURVED-mode adjustment because of the type of the video signal being projected
and the setting values of the CURVED-mode adjustment. In such cases, set the CURVED-mode adjustment values in the range
where the image is displayed without noise.
range becomes narrower than that in the case where you carry out these adjustments individually. When setting the arc setting
value of the CURVED-mode adjustment to 31 or larger, you cannot use the KEYSTONEmode adjustment.
• When carrying out the CURVED-mode adjustment while the option lens is in use, you may not be able to obtain a perfectly
6.20 Changing the AUTO POWER OFF setting

About
The AUTO POWER OFF function of this projector is enabled by default. Change the AUTO POWER OFF setting as necessary.
How to change
2. Select AUTO POWER OFF by pressing the ▲ or ▼ key.
AUTO POWER OFF 5min
Image 6-33
3. Select your desired item by pressing the ◄ or ► key.
6.21 Setting IMAGE REVERSE

Overview
• Set IMAGE REVERSE in the INSTALLATION 1 menu according to the orientation of the projector. The default setting is OFF.
• Select OFF for the combination of floor installation and front projection.
• Select MIRROR INVERT for the combination of ceiling installation and front projection.
• Select MIRROR for the combination of floor installation and rear projection.
• Select INVERT for the combination of ceiling installation and rear projection.
72 R5905597 PHXX SERIES 16/10/2013

How to set
2. Select IMAGE REVERSE by pressing the ▲ or ▼ key.
IMAGE REVERSE OFF
Image 6-34
3. Select OFF, MIRROR, INVERT or MIRROR INVERT by pressing the ◄ or ► key.
6.22 Displaying TEST PATTERN

How to display
2. Select TEST PATTERN by pressing the ▲ or ▼ key.
The cross hatch (red) is displayed.
4. Press once or several times the ENTER key to switch to a different pattern.
The test pattern switches in the order of “cross hatch (red)”, “cross hatch (green)”, “cross hatch (blue)”, “100% white”, “100%
black”, “horizontal color bars”, “vertical color bars”, and INSTALLATION 1 menu.
R5905597 PHXX SERIES 16/10/2013 73

74 R5905597 PHXX SERIES 16/10/2013

7. Initial network settings
7. INITIAL NETWORK SETTINGS

Where to find the settings
You can set the network of the projector using the NETWORK menu in the ADVANCED menu of the OSD Lite menu.

PROJECTOR NAME
NETWORK
CERTIFICATION OFF
NETWORK
PASSWORD ENTER
IP CONFIG ENTER
CONTROL SYSTEM STANDARD
NETWORK RESET OK
NETWORK RESTART OK
Image 7-1
7.1 Setting Projector Name

How to set
1. Display the NETWORK menu.
2. Press the ▲ or ▼ key to select PROJECTOR NAME.
PROJECTOR NAME
Image 7-2

PROJECTOR NAME screen appears.
PROJECTOR NAME
CODE : XXXXX VZ$ %
← →
A B C D E F G H I J K L M DEL
N O P Q R S T U V W X Y Z cap s
0 1 2 3 4 5 6 7 8 9 – . _ NEXT
! ” # $ % ’ ( ) * + , / SP AC E
CLEAR
OK CANCEL
Image 7-3
4. Press the direction keys to move the key cursor, select the characters or marks to enter, and press the ENTER key.
Projector Name can be set using up to 15 characters including alphabets (capital/small), numeric characters, or marks.
← key: Shifting the position of enter cursor to the left for each character.
→ key: Shifting the position of enter cursor to the right for each character.
DEL key: Deleting the character in the position of enter cursor for each character.
caps/CAPS key: Switching an alphabet character to CAPITAL or small.
NEXT/PREV key: Switching the marks listed on the fourth line.
SPACE key: Inserting a space in the position of enter cursor.
CLEAR key: Deleting all the entered characters.
5. When selecting OK, the setting is completed as the name stored. However, when selecting CANCEL, the setting is completed
without storing.
→ The display returns the NETWORK menu after selecting OK or CANCEL.
→ It may take some time to reflect the settings.
R5905597 PHXX SERIES 16/10/2013 75

7.2 Enabling or disabling the network certification

About network certification
You can select whether or not to certify the network communication using the network password.
For details, contact your dealer.
How to enable-disable
2. Press the ▲ or ▼ key to select NET WORK CERTIFICATION.
NETWORK
CERTIFICATION OFF
Image 7-4

Confirmation dialog appears.
NETWORK CERTIFICATION : ON
OK : ENTER CANCEL : MENU
Image 7-5
4. Press the ▲ or ▼ key to select ON or OFF .

→ To cancel the setting, press the MENU key.
7.3 Network Password Settings

How to set
2. Press the ▲ or ▼ key to select NETWORK PASSWORD.
NETWORK
PASSWORD ENTER
Image 7-6

CURRENT NETWORK PASSWORD screen appears.
CURRENT NETWORK PASSWORD
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
← →
N O P Q R S T U V W X Y Z caps
0 1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
Image 7-7
4. Press the direction keys to move the key cursor, select the characters or marks to enter, and press the ENTER key.
Password can be set using up to 32 characters including alphabets (capital/small) or numeric characters.
→ The default password is “admin”.

5. Select OK, and NEW NETWORK PASSWORD screen appears if the entered password is correct.
76 R5905597 PHXX SERIES 16/10/2013

If the entered password is not correct, CURRENT NETWORK PASSWORD screen appears again.
NEW NETWORK PASSWORD

∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
CONFIRM NETWORK PASSWORD
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
← →
↔
N O P Q R S T U V W X Y Z caps
0 1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
Image 7-8
6. Enter the NEW NETWORK PASSWORD and CONFIRM NETWORK PASSWORD.

Password can be set using up to 32 characters including alphabets (capital/small) or numeric characters.
↕ key Shifting the position of enter cursor between NEW NETWORK PASSWORD and CONFIRM NETWORK
PASSWORD.
7. When NEW NETWORK PASSWORD and CONFIRM NETWORK PASSWORD are matched, the setting is completed after chang-
ing the NETWORK PASSWORD.
- When you select OK and the passwords you entered are matched, the setting change dialog is displayed. After the dialog
disappears, the NETWORK menu is displayed.
- When you select CANCEL, the NETWORK menu is displayed without changing the password.
- If the entered content is not matched, NEW NETWORK PASSWORD screen appears again after an error dialog is displayed.
- The password for the web control software of CRESTRON cannot be changed with this setting.
- It may take some time to reflect the settings.
7.4 IP Settings
7.4.1 Start up
How to display
2. Press the ▲ or ▼ key to select IP CONFIG.
IP CONFIG ENTER
Image 7-9

IP CONFIG menu appears.
IP CONFIG
DHCP ON
IP ADDRESS 0. 0. 0. 0
SUBNET MASK 0. 0. 0. 0
DEFAULT GATEWAY 0. 0. 0. 0
MAC ADDRESS
SAVE SETTINGS OK
Image 7-10
7.4.2 Setting or Clearing DHCP
DHCP
Abbreviation for Dynamic Host Configuration Protocol. This protocol automatically assigns IP Address to networked
devices.
R5905597 PHXX SERIES 16/10/2013 77

How to set or clear

1. Display the IP CONFIG menu.
2. Press the ▲ or ▼key to select DHCP.
DHCP ON
Image 7-11
3. Press the ◄ or ► key to select ON or OFF.

→ When setting DHCP to ON, IP ADDRESS, SUBNET MASK, and DEFAULT GATEWAY cannot be set. If you set those settings,
set DHCP to OFF and perform the IP settings as the following procedures.
→ Until the execution of SAVE SETTINGS, the change is not saved.
7.4.3 IP Address Settings
IP Address
Numerical address to identify networked computers.
How to set
2. Press the ▲ or ▼ key to select IP ADDRESS.
IP ADDRESS 0. 0. 0. 0
Image 7-12

IP ADDRESS screen appears.
IP ADDRESS
192 . 168 . 0 . 10 ← →
DEL
0 1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
Image 7-13
4. Press the direction keys to move the key cursor, select the numbers to enter, and press the ENTER key.
Set the numeric value within the range from 0 to 255. However, set the numeric value for the final octet within the range from 1
to 254.
← key: Shifting the position of enter cursor to the left.

→ key: Shifting the position of enter cursor to the right.
5. When selecting OK, the setting is completed as the IP ADDRESS stored temporarily. However, when selecting CANCEL, the
setting is completed without storing.
→ When the setting you entered is correct, the IP CONFIG menu is displayed. If the entered content is not correct, the IP CONFIG
menu is displayed after an error dialog is displayed.
7.4.4 Subnet Mask Settings
Subnet Mask
A numeric value to define the number of bits used for a network address of a divided network (or subnet) in an IP
Address.
How to set
2. Press the ▲ or ▼ key to select SUBNET MASK.
78 R5905597 PHXX SERIES 16/10/2013

SUBNET MASK 0. 0. 0. 0
Image 7-14

SUBNET MASK screen appears.
SUBNET MASK
255 . 255 . 255 . 0 ← →

DEL
0 1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
Image 7-15
4. Enter the Subnet Mask.

Refer to IP Address Settings for the detail of entering.
5. When selecting OK, the setting is completed as the Subnet Mask stored temporarily. However, when selecting CANCEL, the
7.4.5 Default Gateway Settings
Default Gateway
A server (or router) to communicate across networks (subnets) that are divided by Subnet Mask.
How to set
2. Press the ▲ or ▼ key to select DEFAULT GATEWAY.
DEFAULT GATEWAY 0. 0. 0. 0
Image 7-16

DEFAULT GATEWAY screen appears.
DEFAULT GATEWAY
10 . 132 . 1 . 1 ← →
DEL
0 1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
Image 7-17
4. Enter the Default Gateway.

Refer to IP Address Settings for the detail of entering.
5. When selecting OK, the setting is completed as the Default Gateway stored temporarily. However, when selecting CANCEL, the
7.4.6 Saving IP CONFIG Settings
How to save
2. Press the ▼ key to select SAVE SETTINGS.
SAVE SETTINGS OK
Image 7-18
R5905597 PHXX SERIES 16/10/2013 79

→ The setting change dialog is displayed. After the dialog disappears, the NETWORK menu is displayed.
7.5 Setting the control system

How to set
2. Press the ▲ or ▼ key to select CONTROL SYSTEM.
CONTROL SYSTEM STANDARD
Image 7-19
CONTROL SYSTEM : STANDARD

Image 7-20
4. Press the ◄ or ► key to select STANDARD , AMX , or CRESTRON .
STANDARD Select this setting when using Projector Toolset, or RS-232C commands via LAN terminal.
AMX Select this setting when using the controller of AMX.
CRESTRON Select this setting when using the controller or software of Crestron Electronics, Inc.
Important: PJLink™ works regardless of the setting of CONTROL SYSTEM.

It may take some time to reflect the settings.
7.6 Initialization of Network Settings

How to initialize
2. Press the ▲ or ▼ key to select NETWORK RESET.
NETWORK RESET OK
Image 7-21

Confirmation dialog appears.
4. Press the ENTER key again, and the Network Settings can be initialized (except for IP CONFIG).
To cancel the initialization, press the MENU key.
It may take some time to reflect the settings.
7.7 How to Use Network Function

Overview
• When connecting a computer and projector with LAN, configure the both IP Addresses in the same network group.
If connecting in different network group, be sure to use a router. As for the settings of a router, ask the network administrator.
• Configure the IP CONFIG correctly. If the settings are not correct, the communication may be unavailable. For the detail,
consult the network administrator.
• Depending on the settings of standby mode of the projector, LAN function may be unavailable.
80 R5905597 PHXX SERIES 16/10/2013

8. Lamp relay
8. LAMP RELAY
Overview
Using the lamp relay function, you can project images continuously. The lamp relay function automatically rests or switches the
lamps. The lamp relay is performed when LAMP SELECT in the INSTALLATION 1 menu is set to DUAL or SINGLE in the AD-
VANCED menu of the OSD Lite menu.
8.1 Setting the lamp relay interval, LAMP SELECT is set to DUAL
Either of the lamps is automatically put to rest.
How to set
2. Select LAMP SELECT by pressing the ▲ or ▼ key.
LAMP SELECT DUAL
Image 8-1
LAMP SELECT
LAMP SELECT DUAL
Image 8-2
4. Select DUAL by pressing the ◄ or ► key.

6. Select LAMP RELAY by pressing the ▲ or ▼ key.
LAMP RELAY 1H/24H
Image 8-3
7. Select 1H/24H or 2H/1W by pressing the ◄ or ► key.
1H/24H Select this setting when the lamp is operated at a specified time of the day. During the continuous
projection, LAMP 1 or LAMP 2 is automatically turned off for 1 hour in 24 hours. After the interval is set,
the lamps are turned off for 1 hour alternately at the specified interval.
At the time of power-on or menu setting

1 2 3 4 5 6 7 8 (days)
Off
LAMP 1 Illuminating
LAMP 2
Image 8-4
2H/1W During the continuous projection, LAMP 1 or LAMP 2 is automatically turned off for 2 hours in a week.
After the interval is set, the lamps are turned off for 2 hours alternately at the specified interval.

1 2 3 4 5 6 7 8 (days)
Off
LAMP 1 Illuminating
LAMP 2
Image 8-5
R5905597 PHXX SERIES 16/10/2013 81

8. Lamp relay
→ When you select 1H/24H or 2H/1W , the box to set the lamp relay interval is displayed.
→ When the projector is turned off, the setting is cleared and the projector resumes operation from the time of the power-on or
menu setting shown in the preceding step.
1H/24H
NEXT LAMP RELAY
23H ← →
DEL
0 1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
Image 8-6
2H/1W
NEXT LAMP RELAY
6D 22H ← →
DEL
0 1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
Image 8-7
9. Move the key cursor using the direction keys to select the number you want to enter and then press the ENTER key.
→ Maximum interval
1H/24H 23H (23 hours)
2H/1W 6D 22H (6 days and 22 hours)

← key Shifting the position of enter cursor to the left for each character.
→ key Shifting the position of enter cursor to the right for each character.
DEL key Deleting the character in the position of enter cursor for each character.
CLEAR key Deleting all the entered characters.
→ When the value you entered meets the following conditions, an error dialog box is displayed at the screen center.
- The value has been cleared by DEL or CLEAR and left blank.
- The value you entered is out of the setting range.
1H/24H 24H or over
2H/1W 6D 23H or over
→ The value of each item is out of the setting range.
D 7 or over (2H/1W only)

H 24 or over
10.When selecting OK, the setting is completed as the lamp-switching interval stored. However, when selecting CANCEL, the setting
is completed without storing.
→ The display returns the LAMP RELAY menu after selecting OK or CANCEL.
→ The setting you made is applied to NEXT LAMP RELAY in the INFORMATION menu.
Important
• When you use the projector continuously, the lamp relay may not be performed on time due to errors of the clock function.
• Immediately after the power-on, during the lamp selection, or during the lamp relay operation, you cannot change the setting
of LAMP SELECT and LAMP RELAY.
• In the case of continuous projection, the lamps may deteriorate earlier unless they are turned off for 1 hour per week.
• When using this projector continuously for a long time of period, enable LAMP RELAY.
• The brightness and color tint vary at the time of lamp switching.
82 R5905597 PHXX SERIES 16/10/2013

8. Lamp relay
8.2 Setting the lamp relay interval, LAMP SELECT is set to SINGLE
The lamps are automatically switched and used alternately.
How to set
2. Select LAMP SELECT by pressing the ▲ or ▼ key.
LAMP SELECT DUAL
Image 8-8

4. Select SINGLE by pressing the ◄ or ► key.
LAMP SELECT
LAMP SELECT SINGLE
Image 8-9

6. Select LAMP RELAY by pressing the ▲ or ▼ key.
LAMP RELAY 24H
Image 8-10
7. Select 24H or 1 WEEK by pressing the ◄ or ► key.
24H The lamps are switched to each other every day.

1 2 3 4 5 6 7 8 (days)
Illuminating
LAMP 1 Off
LAMP 2
Image 8-11
1 WEEK The lamps are switched to each other every week.

1 2 3 4 5 6 7 8 (days)
LAMP 1 Off
LAMP 2 Illuminating
Image 8-12

When you select 24H or 1 WEEK , the box to set the lamp relay interval is displayed.
24H
NEXT LAMP RELAY
24H ← →
DEL
0 1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
Image 8-13
1 WEEK
R5905597 PHXX SERIES 16/10/2013 83

8. Lamp relay
→ Maximum interval
24H 24H (24 hours)
1 WEEK 7D 00H (7 days and 00 hours)

→ When the value you entered meets the following conditions, an error dialog box is displayed at the screen center.
24H 25H or over
1 WEEK 7D 01H or over
- The value of each item is out of the setting range.
D 8 or over (1 WEEK only)
H 25 or over
10.When selecting OK, the setting is completed as the lamp-switching interval stored. However, when selecting CANCEL, the setting
is completed without storing.
→ The display returns the LAMP RELAY menu after selecting OK or CANCEL.
→ The setting you made is applied to NEXT LAMP RELAY in the INFORMATION menu.
Important
• When you use the projector continuously, the lamp relay may not be performed on time due to errors of the clock function.
• Immediately after the power-on, during the lamp selection, or during the lamp relay operation, you cannot change the setting
of LAMP SELECT and LAMP RELAY.
• In the case of continuous projection, the lamps may deteriorate earlier unless they are turned off for 1 hour per week.
• When using this projector continuously for a long time of period, enable LAMP RELAY.
• The brightness and color tint vary at the time of lamp switching.
84 R5905597 PHXX SERIES 16/10/2013

9. Advanced features
9. ADVANCED FEATURES
9.1 Password function

About the password function
This projector is equipped with the password function that is designed for prevention of wrong operation by children and restriction
on operation by other than specified users. The password function has 3 modes as follows.
DISPLAY INPUT When the projector is turned on, the startup screen (or splash screen) will appear and stay on the screen
until the password is entered. When the password is entered, the startup screen will switch to the regular
operation screen.
MENU ACCESS All the keys except for the POWER key on the projector are disabled. (The keys on the remote control
are enabled.) You can use this mode as a measure of prevention of wrong operation by children and
restriction on operation by other than specified users.
SPLASH ID IMAGE CAPTURE and SPLASH SCREEN in the INSTALLATION 2 menu become unavailable. SPLASH
SCREEN SCREEN will be set to ON automatically.
9.1.1 Enabling the password function
How to enable
1. Display the FEATURE menu.
2. Press the ▲ or ▼ key to select PASSWORD FUNCTION.
3. Press the ◄ or ► key to change the mode among DISPLAY INPUT , MENU ACCESS and SPLASH ID SCREEN .
When the password has already been set, the mode won’t be changed. In such cases, press the ENTER key to cancel the
password function and try again.
The screen for setting the password function will appear.

DISPLAY INPUT
LOCK ENTER
UNLOCK ENTER
Image 9-1

The screen for entering a password will appear.
PASSWORD
CONFIRM
1
4 2 O K : ENTER CANCEL : MENU
3
Image 9-2
6. Enter a 4 - 8 digit password using the ▲, ►, ▼ and ◄ keys.

(▲=1, ►=2, ▼=3, ◄=4)
To cancel the procedure, press the MENU key.
8. Enter the password again for confirmation using the same steps.
→ If the entered passwords don’t match, an error message will appear.
→ To cancel the procedure, press the MENU key.
R5905597 PHXX SERIES 16/10/2013 85

9.1.2 Cancel the password function
How to cancel
2. Press the ▲ or ▼ key to select PASSWORD FUNCTION.
The screen for canceling the password function will appear.

DISPLAY INPUT
LOCK ENTER
UNLOCK ENTER
Image 9-3

The screen for entering the password will appear.
PASSWORD
CONFIRM
1
4 2 O K : ENTER CANCEL : MENU
3
Image 9-4
5. Enter a 4 - 8 digit password using the ▲, ►, ▼ and ◄ keys.

(▲=1, ►=2, ▼=3, ◄=4)
→ If you enter a wrong password, an error message will appear.
→ To cancel the procedure, press the MENU key.
Important
Disable the password by pressing the MENU and ENTER keys on the projector at the same time about 3 seconds
9.2 Split
for PHWU-81B/PHWX-81B only
About split
You can split the screen in two and display a computer image on the left screen and a video image on the right screen.
A B
Image 9-5
A Left image
B Right image
To use the split mode:

1. Display the INSTALLATION 1 menu in the ADVANCED MENU.
2. Select SPLIT.
86 R5905597 PHXX SERIES 16/10/2013

3. Press ENTER key.

The screen is split in two and the left and right screens display the following images:
Left Image supplied to the last selected input source, VGA (COMPUTER1), 5BNC (COMPUTER2), DVI, HDMI or
screen SDI (for PHWU-81B only)
Right Image supplied to the last selected input source, VIDEO or S-VIDEO
screen
Important
• When you press the MENU key, the screen is displayed in the normal mode.
• Also, when you change the input source, the screen is displayed in the normal mode.
• In the split mode, the picture quality settings of the input source in the normal mode to be displayed on the left screen are
reflected on the entire screen.
• When no signal is input, a blue screen is displayed.
• When you input an interlace signal to the left screen, the displayed image may shake up and down slightly, but this is not a
malfunction.
• When you display 60-Hz and 50-Hz video signals at the same time, motion images may not be displayed properly. In this case,
set VERT. SYNC. of USER in the SIGNAL menu to OFF for the left screen.
• You cannot use the split mode unless a signal is being input.
• Displaying the screen split in two may take some time depending on the signal.
To change the input source of the left or right screen:

• To change the input source of the left screen, press the ◄ key on the remote control. Each time the the ◄ key is pressed, the
input source setting changes in order of VGA (COMPUTER 1) → 5BNC (COMPUTER 2) → DVI → HDMI → SDI (for PHWU-
81B only) → VGA (COMPUTER 1) ....
• To change the input source of the right screen, press the ► key on the remote control. Each time the the ► key is pressed, the
input source setting changes in order of VIDEO → S-VIDEO → VIDEO ....
9.3 Picture in Picture (PIP)
for PHXG- 91B only
About Picture in Picture

One of the special features of this projector is the picture-in-picture (PIP) mode. The PIP mode allows you to view the images from
different sources at the same time.
While viewing the image from the VGA (COMPUTER1), 5BNC (COMPUTER2), DVI, or HDMI input source, you can display the
image from the VIDEO or S-VIDEO input source as a sub image.
A
Image 9-6
A Sub image
To use the PIP mode:

1. Display the INSTALLATION 1 menu in the ADVANCED MENU.
2. Select PIP.
3. Press ENTER key.
Sub image is displayed.
R5905597 PHXX SERIES 16/10/2013 87

4. Repeat the previous steps to remove the PIP mode.

5. To change the position of the sub image, press the ◄ or ► key on the remote control.
Important
• The PIP mode is available only when the ASPECT ratio is set to NORMAL.
• The PIP mode isn’t available with some input signals.
• When the main image signal is lost during the PIP mode, the PIP mode is disabled.
• When there is no video signal for sub image, you can’t change the display position.
• The motion may not run smoothly in the PIP mode.
• You cannot make the MULTI-SCREEN menu settings and SIGNAL menu settings in the PIP mode.
• The size of the sub image varies depending on the input signal and the settings.
9.4 Supervising and controlling by computer

What can be done?
You can supervise and control the projector’s operation using a personal computer via a LAN.
Projector Toolset
Barco’s Projector Toolset software is a free, userfriendly software package that helps you manage your Barco projectors easily
and quickly from one central location, through the network or RS232 connection. Comprising various tools for brightness settings,
diagnostics, image adjustment, picture-in-picture and image control, the Projector Toolset is an indispensable tool for efficient visu-
alization management.
The Projector Toolset provides your facility management with an intuitive way to manage an entire fleet of projectors. For example,
in college buildings, museums, conference centers or other facilities with a complex visualization network, clicking one button from
the comfort of a desktop computer to start up your projector fleet has a huge impact on your time management. For Details, see the
website of Barco. URL http://www.barco.com > Projector Toolset
AMX Device Discovery

The projector is monitored and controlled by the controller system of AMX.
This is a technology suggested by AMX to facilitate configuration of the control system of AMX and its target devices. To use
this technology, it is necessary to set CONTROL SYSTEM in the NETWORK menu. For details, see the website of AMX. URL
http://www.amx.com/
Crestron RoomView Connected™

The projector is monitored and controlled by the controller system and software of Crestron Electronics, Inc.
This is a technology suggested by Crestron Electronics, Inc. to facilitate configuration of the control system of Crestron and its target
devices. To use this technology, it is necessary to set CONTROL SYSTEM in the NETWORK menu. For details, see the website of
Crestron Electronics, Inc. URL http://www.crestron.com URL http://www.crestron.com/getroomview/
Important:
• When you set CONTROL SYSTEM to CRESTRON in the NETWORK menu, the web control for Crestron is enabled. For such
control, Adobe Flash Player should be installed in advance. You can download Adobe Flash Player from the website of Adobe
Systems Incorporated.
• When you set CONTROL SYSTEM to CRESTRON in the NETWORK menu, you cannot use the control by Projector Toolset,
which is the software supplied with the projector.
PJLink™
This projector supports standard protocol PJLink™ for projector control and you can control and monitor projector’s operations using
the same application among projectors of different models and different manufacturers.
About PJLink™
• To use PJLink™ function, the PJLink™ application software is required.

• To use this function, set the network certification properly according to the setting of the network application to be used.
• For the specifications of PJLink™, access to the Web site of Japan Business Machine and Information System Industries As-
sociation (JBMIA). (http://pjlink.jbmia.or.jp/english)
• This projector is fully compliant to the specifications of JBMIA PJLink™ Class 1. It supports all the commands defined by
PJLink™ Class 1, and the compliance has been verified with the PJLink™ standard specifications Version 1.0.
Important:
88 R5905597 PHXX SERIES 16/10/2013

• For the commands for PJLink™, see the table on the next page.
• The control may not be performed correctly or the monitoring data may not be obtained correctly in the following conditions:
- During standby
- During zoom/focus adjustment
- During lens shift adjustment
- During input source switching
- During auto position execution
- During BLANK
- During command processing
- Before the splash screen disappears after the power is turned on.
• During zoom/focus adjustment, lens shift adjustment, BLANK, etc., it may take approx. 5 seconds to receive a response to a
command.
• Use 1 controller to control/monitor 1 projector.
• For how to control/monitor using PJLink™, see the operation manual of the PJLink™ application you use.
• When you monitor the projector’s operating state using this function by issuing inquiry commands successively, issue an inquiry
command after receiving the response to the previous inquiry command from the projector.
Connection
When STANDBY MODE of the INSTALLATION 1 menu of the projector is set to LOW, the network function is disabled. To enable
the network function, set STANDBY MODE to STANDARD.
Configure the initial network settings first.
You can configure the initial settings using the projector menu.
PJLink™ supported commands

The table below shows commands to control the projector using the PJLink™ protocol.
Command Description Remark (Parameter)

POWR Power control 0 = Standby
1 = Power on
POWR? Inquiry about the power state 0 = Standby
1 = Power on
2 = Cooling down
3 = Warming up
INPT Input switching 11 = COMPUTER1
INPT? Inquiry about input switching 12 = COMPUTER2
21 = VIDEO
22 = S-VIDEO
31 = HDMI
32 = DVI
33 = SDI (only PHWU-81B only)
AVMT Mute control 30 = Video mute disable
31 = Video mute enable
AVMT? Inquiry about the mute state
ERST? Inquiry about the error state 1st byte: Fan error, 0 or 2
2nd byte: Lamp error, 0 to 2
3rd byte: Temperature error, 0 or 2
4th byte: Cover open error, 0 or 2
5th byte: Filter error, 0 or 2
6th byte: Other error, 0 or 2
0 to 2 mean as follows:
0 = No error detected, 1 = Warning, 2 = Error
R5905597 PHXX SERIES 16/10/2013 89

Command Description Remark (Parameter)

LAMP? Inquiry about the lamp state 1st value (1 to 5 digits): Cumulative LAMP 1 operating time (This item
shows a lamp operating time (hour) calculated based on that LAMP
MODE is STANDARD.)
2nd value: 0 = Lamp off, 1 = Lamp on
3rd value (1 to 5 digits): Cumulative LAMP 2 operating time (This item
shows a lamp operating time (hour) calculated based on that LAMP
MODE is STANDARD.)
4th value: 0 = Lamp off, 1 = Lamp on
INST? Inquiry about the available The following value is returned. “11 12 21 22 31 32 33”
inputs
NAME? Inquiry about the projector The projector name set on the NETWORK menu is returned.
name
INF1? Inquiry about the manufacturer “BARCO” is returned.
name
INF2? Inquiry about the model name “PHWU-81B”, “PHWX-81B”, or “PHXG-91B” is returned.
INF0? Inquiry about other information No other information is available. No parameter is returned.
CLSS? Inquiry about the class “1” is returned.

information
This projector is fully compliant to the specifications of JBMIA PJLink™ Class 1. It supports all the commands defined by PJLink™
Class 1, and the compliance has been verified with the PJLink™ standard specifications Version 1.0.
9.5 Monitoring and control using SERIAL terminal

Overview
Using the SERIAL terminal, you can monitor and control multiple projectors collectively or individually.
For details, contact your dealer.
A A
C D C D C D
Image 9-7
A RS-232C cable (option)
B To RS-232C terminal
C To SERIAL IN
D To SERIAL OUT
See also the instruction manuals of the devices to be connected.
Connection
Make sure that the power supplies of the projector and the computer are off.
1. Connect one end of a commercially available RS-232C cable to the SERIAL IN terminal on the projector to be connected to the
computer.
2. Connect the other end of the RS-232C cable to the serial port on the computer.
3. Connect one end of an RS-232C cable to the SERIAL OUT terminal on the projector that is connected to the computer.
4. Connect the other end of the RS-232C cable to the SERIAL IN terminal on the second projector.
For the connection of the second and later projectors, connect their SERIAL OUT terminals and the SERIAL IN terminals using
RS-232C cables.
90 R5905597 PHXX SERIES 16/10/2013

Important:
In a system using a serial divider, don’t connect the projectors as above.
To monitor and control the projectors collectively or individually, it is necessary to assign GROUP IDs to them.
Setting GROUP IDs

By dividing the projectors into groups, you can monitor and control them collectively by groups. GROUP IDs should be A to Z. You
can create up to 26 groups.
→ The default GROUP ID is A.
2. Select GROUP ID by pressing the ▲ or ▼ key.
3. Set the GROUP ID by pressing the ◄ or ► key.
Important:
• When you want to monitor and control the projectors by groups, set a different GROUP ID.
• For details, contact your dealer.
9.6 Control by a control panel, etc.

Overview
When installing the projector in a place where the remote control signals cannot reach the projector, you can control the projector
using a control panel or other device connected to the REMOTE 1 IN terminal.
R emote control External contact

control
POWER
ON OFF
BLANK
ON OFF
COMPUTER1 COMPUTER2
VIDEO S-VIDEO
DVI
A
B
Image 9-8
A Projector
B Control panel
Controllable functions
• Switching between remote control and external control
• Switching input signals
• Power-on and power-off
• BLANK-on and BLANK-off
Important:
To control the projector using a control panel, set STANDBY MODE in the INSTALLATION 1 menu to STANDARD. When it is LOW,
you cannot control the projector.
Connections
Make sure that the power supplies of the projector and control panel are off.
R5905597 PHXX SERIES 16/10/2013 91

B
C
Image 9-9
A To REMOTE 1 IN
B RS-232C cable (option)
C Control panel
1. Connect one end of an RS-232C cable to the REMOTE 1 IN terminal on the projector.
2. Connect the other end of the RS-232C cable to the control panel.
Pin functions (defaults)

Connect the other end of the RS-232C cable to the control panel.
Pin No. Signal Open (H) Short (L)

1 GND - GND
2 POWER OFF ON
3 Input - COMPUTER1
4 Input - COMPUTER2
5 Input - VIDEO
6 Input - S-VIDEO
7 Input - DVI
8 BLANK OFF ON
9 ON/OFF Valid (Remote control) Invalid (External contact control)
→ You can change the functions of PIN 2 to PIN 8 using REMOTE 1 MODE in the INSTALLATION 2 menu.
Important:
To reset the pin functions to the defaults, set REMOTE 1 MODE in the INSTALLATION 2 to RESET.
Contact control
By short-circuiting Pin No. 1 and Pin No. 9, you can control the projector using a control panel or other device.
When you short-circuit Pin No. 1 and Pin No. 9, the following functions cannot be used:
• POWER and BLANK of the remote control and the projector
• RS-232C commands and network functions corresponding to the above-mentioned functions
• REMOTE 1 MODE, AUTO POWER ON and AUTO POWER OFF in the INSTALLATION 2 menu.
• STANDBY MODE in the INSTALLATION 1 menu.
Input switching control

By short-circuiting any of Pin No. 3 to Pin No. 7, you can switch the input using a control panel or other device.
When short-circuiting any of Pin No. 3 to Pin No. 7, you cannot use the following functions.
• POWER, BLANK, COMPUTER 1, COMPUTER 2, VIDEO, S-VIDEO, DVI, HDMI, and SDI (for PHWU-81B only) of the remote
control and the projector
• RS-232C commands and network functions corresponding to the above-mentioned functions
POWER control
By short-circuiting or open-circuiting Pin No. 2, you can turn on or off the power using a control panel or other device.
BLANK control
By short-circuiting or open-circuiting Pin No. 8, you can turn on or off the BLANK function using a control panel or other device.
92 R5905597 PHXX SERIES 16/10/2013

10. Lamp replacement
10. LAMP REPLACEMENT
10.1 Lamp replacement warnings

Warnings
• Be careful not to drop the lamp fixing screws into the inside of the projector. Don’t put a metal piece or flammable object into the
projector. Using the projector with any foreign object present inside may result in electric shock or fire. When you can’t remove
the foreign object from the inside, contact your dealer for removal.
• Do not touch the lamp with bare hands or give a shock to the lamp. Attach the lamp properly. Improper handling may cause
explosion.
• Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation may also
result in fire.
• Don’t shake the removed lamp or don’t lift it above your face. You may be injured in your eye by flying or falling glass fragments.
• Don’t replace the lamp immediately after use because the lamp cover is very hot. You may get burned. Turn off the power
using the POWER key. After the lamp goes out, wait about 2 minutes until the intake and exhaust fans for cooling the lamp
stop rotating. Then unplug the power cord, and wait at least 1 hour to allow the lamp to cool down enough to the touch.
10.2 Interval of lamp replacement

About the lamp
This projector is equipped with 2 lamps to project images. This lamp is a consumable. It may burn out or its brightness may decrease
during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new lamp
separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp.
Spare lamp: H LAMP 350W
About lamp replacement interval

The recommended interval of lamp replacement is about 4000 hours12of consecutive use. Such interval differs depending on the
operating environment and may be shorter than 4000 hours12. Decrease in luminescence and/or color brightness indicates that the
lamp needs to be replaced. When the lamp operation time exceeds 3000 hours1, the lamp replacement message will appear on
the screen for 1 minute everytime the lamp is turned on. When the lamp has been used for about 3800 hours1, the replacement
message (IT’S TIME FOR LAMP * REPLACEMENT) will appear on the screen for 1 minute every 20 hours1 thereafter. When the
lamp operation time exceeds 4000 hours12, the projector automatically shuts off.
Caution
• Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a breakdown.
• This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may explode or fail
to illuminate permanently because of an impact, scratch, or deterioration through use. The period of time until explosion or
permanent failure to illuminate varies considerably from lamp to lamp, depending on operation conditions. Therefore, the lamp
may explode soon after the start of use.
• The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction of lamp
replacement appears, replace it with a new one immediately even if the lamp is still lighting normally.
• When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and the gas charged
inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains mercury. Be careful not to breathe
it or avoid it from entering your eye or mouth. If you should breathe it or if it should enter your eye or mouth, see a doctor
immediately.
• In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the projector. Ask
your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace the lamp by yourself, be
sure to hold the handle of the lamp. You may get injured by glass fragments.
• When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the projector or option
lamp to prevent glass fragments from scattering.
• Be sure to use the lamp exclusive to this projector, H LAMP 350W. Use of other lamps may cause a failure of the projector.
Before replacing the lamp

Check which lamp is to be replaced using the INFO menu in the OSD Lite menu.
1. Duration when LAMP MODE of the INSTALLATION 1 menu is set to LOW. When it is set to STANDARD, this duration will be shorted.
2. When LAMP MODE is set to STANDARD, this duration will be shorted to 2000 hours.
R5905597 PHXX SERIES 16/10/2013 93

Image 10-1
10.3 Lamp replacement
How to replace
1. Unplug the power cord from the outlet or appliance inlet.
(a) (c)
(b)
Image 10-2
Image 10-3
4. Loosen two screws (d) that are securing the lamp cover using a Phillips screwdriver and remove the lamp cover (e) from the
projector.
94 R5905597 PHXX SERIES 16/10/2013

(e)
(d)
Image 10-4
5. Loosen two screws (f) that are securing the lamp box to be removed using a Phillips screwdriver.
2 1
(f) (f)
Image 10-5
6. Pull the handle.

7. Pull out the lamp box by the handle while holding the projector.
Image 10-6
- Pull the lamp box out of the projector slowly. When the lamp is broken, glass fragments may be scattering by quickly pulling
out the lamp box.
- Do not spill liquid on the removed lamp box or do not place it near any flammable object or where children can reach to prevent
injury or fire.
8. Load a new lamp box securely into the projector in the right orientation.
Image 10-7
9. Put the handle back to the original position.

Note: Make sure that the handle is locked.
10.Tighten two screws (f) of the new lamp box tightly using a Phillips screwdriver.
2 1
(f) (f)
Image 10-8
Note: Make sure that the screws are tightened firmly.
11. Insert the lamp cover (e) into the projector and tighten two screws (d) on the lamp cover firmly using a Phillips screwdriver.
R5905597 PHXX SERIES 16/10/2013 95

(e)
(d)
Image 10-9
Note: You cannot turn on the projector without attaching the lamp cover.
12.Insert the side cover (c) into the projector and tighten two screws (a) on the rear and two screws (b) on the side of the side cover
using a Phillips screwdriver.
(a) (c)
(b)
Image 10-10
10.4 Reset of the lamp operation time

What can be done?
You can reset the lamp operation time of the newly installed lamp using the menu.
How to reset
1. Plug the power cord into the wall outlet.
2. Press the POWER key.
3. Display the FEATURE menu in the ADVANCED menu.
4. Select ADVANCED MENU by pressing the ▲ or ▼ key.
ADVANCED MENU ENTER
Image 10-11

6. Select LAMP 1 TIME RESET or LAMP 2 TIME RESET by pressing the ▲ or ▼ key.
LAMP 1 TIME RESET OK
LAMP 2 TIME RESET OK
Image 10-12

The confirmation dialog appears.
EXECUTE LAMP 1 TIME RESET ?

Image 10-13
8. Reset by pressing the ENTER key.

When the lamp operating time is not reset, press the MENU key.
96 R5905597 PHXX SERIES 16/10/2013

Important
• When the operation times of both lamps have exceeded 4000 hours3, you can operate the projector only for 3 minutes after
turning on the power. During this time, carry out steps 15 to 20 to reset the lamp operation times.
• The projector doesn’t turn on if the lamp cover isn’t attached securely.
• Be sure to reset the lamp operation time whenever you replace the lamp.
• Do not reset the lamp operation time unless you replace the lamp.
• The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.
CAUTION: This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the
lamp may be regulated due to environmental considerations. For disposal or recycling information, please
contact your local authorities or the Electronic Industries Alliance: www.eiae.org. (For the U.S. only.)
3. When LAMP MODE is set to STANDARD, this duration will be shorted to 2000 hours.
R5905597 PHXX SERIES 16/10/2013 97

98 R5905597 PHXX SERIES 16/10/2013

11. Maintenance
11. MAINTENANCE
WARNING: Do not use flammable solvents (benzene, thinner, etc.) and flammable aerosols when cleaning
the projector body and lens. Flammable substances may ignite causing fire or breakdown while the lamp is
illuminating.
CAUTION: Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform
any maintenance on the projector.
Ask your dealer for annual cleaning of the inside of the projector. If you continue to use the projector with
dust inside, it may result in fire or malfunction.
Do not put any foreign object into the filter unit. It may cause malfunction.
11.1 Cleaning of the projector and the vents

About the cleaning
Use a soft cloth to clean the projector and the vents. When the vents become dirty, wipe them with a soft cloth dampened with
diluted mild detergent, and then wipe them with a dry cloth.
Clean the inside of the side and rear covers frequently as dust is apt to be collected.
To protect the surface of the projector from fading or deteriorating:
• Do not spray insecticide on or inside the projector.
• Do not use benzine or thinner to clean it.
• Do not let rubber or plastic materials contact with projector.
11.2 Cleaning of the lens

About cleaning the lens
Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning fluid. The lens surface is fragile. Use only
recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your fingers.
11.3 Automatic cleaning filter

About cleaning filter
This projector is equipped with an automatic cleaning filter. The burdensome filter cleaning is automatically carried out.
• cleaned after the designated time elapses.

• When the cumulative operation time since the last cleaning of the automatic cleaning filter exceeds the designated time, the
filter is cleaned automatically after you turn off the projector by pressing the POWER key.
Important:
When the cumulative operation time has exceeded the designated time and you run the projector continuously for 24 hours after
turning on the power, the automatic cleaning filter works while the projector is operating.
11.3.1 Setting the cleaning interval
What can be done?

You can set the cleaning interval of the automatic cleaning filter using the menu.
How to set
1. Display the INSTALLATION 2 menu in the ADVANCED menu.
2. Select FILTER MENU by pressing the ▲ or ▼ key.
R5905597 PHXX SERIES 16/10/2013 99

11. Maintenance
FILTER MENU ENTER
Image 11-1

4. Select CLEANUP PERIOD by pressing the ▲ or ▼key.
CLEANUP PERIOD 1 WEEK
Image 11-2
5. Select 24H or 1 WEEK by pressing the ◄ or ► key.
24H The filter is cleaned about every 24 hours.
1 WEEK The filter is cleaned about every 168 hours.

When you select 24H or 1 WEEK , the box to set the cleaning interval is displayed.
24H
NEXT CLEANUP
24H ← →
DEL
0 1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
Image 11-3
1 WEEK
NEXT CLEANUP
7D 00H ← →
DEL
0 1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
Image 11-4
Maximum interval
24H 24H (about 24 hours)
1 WEEK 7D 00H (about 168 hours)

When the value you entered meets the following conditions, an error dialog box is displayed at the screen center for 3 seconds.
24H 25H or over
1 WEEK 7D 01H or over
100 R5905597 PHXX SERIES 16/10/2013

11. Maintenance
- The value of each item is out of the setting range.
D 8 or over (1 WEEK only)

H 7D 01H or over
8. Select OK to accept the interval you entered and exit the menu, or select CANCEL to exit the menu without saving the setting.
When you select OK or CANCEL, the CLEANUP PERIOD menu is displayed.
11.3.2 How to clean the automatic cleaning filter
Preparations
Check the amount of dust through the dust check window of the filter cover and clean it, if necessary. Before cleaning the filter, be
sure to unplug the power cord from the outlet.
• Wen the dust box of the automatic cleaning filter is filled up with dust, the cleaning ability decreases. If you use the projector
in such a state, the filter is covered by the dust and the temperature inside the product abnormally rises, damaging the internal
parts and components and affecting the panel’s lifetime, resulting in a breakdown.
• When the temperature inside the projector is abnormally high, the projector may automatically turn off and go into the standby
mode where the light source lamps are off to protect the internal parts and components.
How to clean
(c)
(b)
(a)
Image 11-5
Image 11-6
3. Remove the automatic cleaning filter.
R5905597 PHXX SERIES 16/10/2013 101

11. Maintenance
Image 11-7
4. Remove the dust box from the automatic cleaning filter and get rid of the dust from it.
Suck dirt and dust from the automatic cleaning filter and projector using a vacuum cleaner.
Image 11-8
5. Attach the dust box to the automatic cleaning filter.
Image 11-9
6. Attach the automatic cleaning filter.
Image 11-10
7. Insert the side cover (c) into the projector and tighten two screws (a) on the rear and two screws (b) on the side of the side cover
firmly using a Phillips screwdriver.
(c)
(b)
(a)
Image 11-11
102 R5905597 PHXX SERIES 16/10/2013

12. Troubleshooting
12. TROUBLESHOOTING
Advise
Before asking for repair of the projector, check the following. If the symptom persists, stop using the projector, be sure to unplug the
power plug, and then contact your dealer.
12.1 No image appears on the screen

Overview
Problem Solution
Power can not be turned on. Check whether the STATUS Led is on or off and how it is lightning.
No image appears on the
screen. • Press any key to cancel BLANK
• Check that the lens cap is removed.
• It may take about 2 minutes for the lamp to light up.
• The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and
then try again.
• If the projector was turned off before the lamp was cooled down sufficiently last time, the
fan may start rotating and the POWER key may not work after the power cord is plugged.
After the fan stops rotating, press the POWER key to turn back on the STATUS Led.
• Set SCART INPUT in the FEATURE menu to OFF.
• Check that the intake vent is clean.
• Check that the cables connected to the external devices are not broken.
• When an extension cable is being used, replace it with the supplied cable for check.
When images are displayed correctly, add an RGB signal amplifier to the extension cable.
Power turns off.
• This problem may occur when the intake vent and/or exhaust vents are blocked.
→ Remove the objects blocking the intake vent and/or exhaust vents and then carry out
the following procedure.
a) Wait for the intake fan and/or exhaust fan to stop.
b) Unplug the power cord from the wall outlet.
c) Wait about 10 minutes.
d) Plug the power cord into a wall outlet.
e) Press the POWER key.
• Check that AUTO POWER OFF has been set to OFF.
• If the lamp has deteriorated, it may go out after a while it illuminates.
The screen for entering the PASSWORD FUNCTION in the FEATURE menu has been set to DISPLAY INPUT to
password appears. enable the password lock.
→ Enter the password or contact the person in charge of management of the projector.
Splash image is kept displayed.
• Turn on the power of the connected device, or check whether there is something wrong
with the connected device.
• Checke whether the external device output signals. (Check this especially when the
external device is a notebook computer.)
• Check that the cable connected to the external device is not defective.
• Check that the projector is connected to the external device using the correct terminals.
• Check that the connected device is correctly selected as the input source.
• When an extension cord is being used, replace it with the supplied cable and check
whether images are projected correctly. If images are projected correctly, use an RGB
signal amplifier along with the extension cord.
R5905597 PHXX SERIES 16/10/2013 103

12. Troubleshooting
12.2 Images are not displayed correctly

Overview
Problem Solution
Projected images are shaking.
• Check that the cable connected to the external device isn’t intermittent.
Projected images are
displaced. • Connect the cable’s plug with the external device’s connector firmly.
• Project an image containing many characters such as a help menu and execute AUTO
The edge of the projected POSITION.
images is not displayed.
• Some computers output out-of-spec signals on rare occasion. Adjust the SIGNAL menu.
• Check whether there is a wind that blows the exhausted air from the projector to the
direction of the projection lens.
Projected images are distorted. Adjust the projector and the screen so that they are perpendicular to each other.
Projected images are dark.
• Adjust BRIGHTNESS and CONTRAST in the IMAGE menu.
• Replace the lamp.
• Decrease the temperature when the ambient temperature is high and the warning is
displayed.
Projected images are blurred.
• Adjust the focus.
• Clean the lens.
• Adjust FINE SYNC. in the SIGNAL menu to eliminate flicker.
• Adjust TRACKING and FINE SYNC. in the SIGNAL menu.
• Adjust BRIGHTNESS and CONTRAST in the IMAGE menu.
• Adjust the projector and the screen so that they are perpendicular to each other.
White dots are seen on This symptom is normal for a DLP™ projector and is not a malfunction. (A very small number
projected images. of pixels may stay lit or out, but such symptom is not a malfunction. Pixels of 99.99% or
more are effective.)
Black dots are seen on
projected images.
Rainbow effect is seen on This is due to color breaking noise that occurs in a DLP™ system and is not a malfunction.
projected images.
Fine streaks are seen on
projected images. • This is due to interference with the screen surface and is not a malfunction. Replace
the screen or displace the focus a little.
• Vertical or horizontal streak noise may appear on the projected image, depending on the
type of the DVD player or game console you use. In such a case, you can reduce such
streak noise by enabling the LPF.
Projected images become
wavy. • Connect the plugs of the cables to external devices securely.
• Keep the projector away from devices that emit interfering radio waves.
• When the keystone adjustment is carried out, the image may not be displayed correctly
depending on the type of input signal. This isn’t a product malfunction. In this case,
readjust the keystone so that the amount of keystone correction is as small as possible.
Hue is not appropriate.
• If RGB/YCbCr output setting on the external device does not match with COMPUTER
INPUT setting in the SIGNAL menu on the projector, the entire screen may become
reddish or greenish.
• If the setting of COMPUTER INPUT in the SIGNAL menu is inconsistent with the RGB/
YCbCr output setting of the external device even when the input source is other than
COMPUTER (for example, when the input source is HDMI), the entire image appears
reddish or greenish.
→ Check that COMPUTER INPUT in the SIGNAL menu is set correctly.
• Check that the cables connected to the external devices are not broken.
Tint in projected images is
incorrect. • Check that COMPUTER INPUT in the SIGNAL menu is correctly set.
• Check that the cable connected to the external device isn’t broken.
Different color tint.
• When comparing images projected by two projectors, tints in the displayed images may be
different because of variation between their optical components. This is not a malfunction.
• When comparing the image projected by this projector with those displayed on the
television or PC monitor, tints in the displayed images may be different because of
difference in the range of color reproducibility. This is not a malfunction.
104 R5905597 PHXX SERIES 16/10/2013

12. Troubleshooting
Problem Solution
Only the motion areas in the This is caused by the computer being used. Contact the manufacturer of your computer.
images supplied from the
computer aren’t displayed.
Projected images are obscured.
• Match the output resolution of your computer with the resolution of the projector. For
the method to change the output resolution of the computer, contact the manufacturer
of your computer.
• Some images and texts appear obscured during the keystone adjustment. In such cases,
use the projector without applying the keystone adjustment.
• When SUPER RESOLUTION is ON, the displayed image may be obscured. Set it to OFF.
Noise appears around the In some images such as DVD, noise may appear around the recorded image. In this case,
image. decrease the setting value of OVER SCAN in the SIGNAL menu or adjust the setting value of
SHUTTER in the USER menu of the SIGNAL menu.
The resolution setting on the
computer is different from that • On the computer, display the images containing many characters such as a text document
displayed in INFORMATION so that the screen becomes bright as much as possible, and then execute AUTO
menu on the projector. POSITION.
• Perform RESOLUTION (MEMORIZE) in the SIGNAL menu.
• Depending on the computer, the images may be output in the different resolution from the
setting. In such a case, consult the computer manufacturer.
The projected images have
blown-out highlights or • Adjust the input level of ADVANCED menu in the IMAGE menu
blocked-up shadows. • Set COLOR ENHANCER in the IMAGE menu to the setting such as STANDARD and
sRGB.
Images of WXGA signal are not Make adjustment according to “How to adjust the computer image”
displayed correctly.
12.3 Other problems

Overview
Problem Solution
The exhaust vents emit warm This air comes out after cooling the inside of the projector. You may feel hot, but this is not
air. a malfunction.
The menu can’t be used.
• The microcomputers inside the projector may be wrongly operating because of noise.
→ Press the POWER key to turn off the lamp, wait for about 2 minutes and unplug the
power cord from the wall outlet. Wait about 10 minutes, plug the power cord in, and try
again.
• You cannot select (or set) grayed-out items. Whether items can be selected or not
depends on the presence of an input signal at the time when the menu is displayed, the
type of such input signal, and other conditions.
“HIGH TEMP WARNING” is
displayed. • This indication appears when the ambient temperature rises high. When the ambient
temperature stays high, the lamp goes out.
→ Eliminate any causes of the rise in the ambient temperature.
• This indication appears when the intake or exhaust vents are blocked. When they are
kept blocked, the lamp goes out.
→ Remove the objects blocking the intake or exhaust vents.
The mark Ø appears. This mark appears when ineffective operation is carried out. This isn’t a product malfunction.
This mark appears when
ineffective operation is carried • Check that the batteries are loaded in the remote control or the batteries are not weak.
out. This isn’t a product • Check that the remote control sensor isn’t exposed to direct sunlight or fluorescent light.
malfunction. The remote
• Use the remote control within its operation range.
control doesn’t function easily
or at all. • Use the remote control at least 10 cm away from the projector.
• Check that the projector isn’t controlled by a control panel or other device that is
connected to the REMOTE 1 IN terminal.
• Check that the REMOTE 2 IN and OUT terminals are not used.
R5905597 PHXX SERIES 16/10/2013 105

12. Troubleshooting
Problem Solution
The keys on the projector
(except for the POWER key) • PASSWORD FUNCTION in the FEATURE menu has been set to MENU ACCESS to
don’t function. enable the password lock.
→ Cancel the password lock or contact the person in charge of management of the projec-
tor.
• Check that the projector isn’t controlled by a control panel or other device that is
connected to the REMOTE 1 IN terminal.
Abnormal sound is heard. Because the color wheel spins at a high speed, metallic sounds may be heard in rare
occasions. Such symptom is not a malfunction.
FOCUS/ZOOM doesn’t work. Check that LENS LOCK in the INSTALLATION 1 menu isn’t ON.
Lens shift doesn’t work.
If the following problem occurs after the lamp is replaced, check the following first.
Problem Solution
The projector does not turn on. Fit the lamp cover securely.
The STATUS Led blinks. Reset the lamp operating time of the newly installed lamp.
Kensington Lock
This projector has a Kensington Security Standard connector for use with Kensington MicroSaver Security System. Refer to the
information that came with the Kensington System for instructions on how to use it to secure the projector. Please contact Kensington
Technology Group below.
Kensington Technology Group
2855 Campus Drive
San Mateo, CA 94403, U.S.A.
Phone: +1- (650)572-2700 Fax: +1- (650)572-9675
12.4 Led
Overview
The STATUS Led shows the operation condition of the projector.
L 1 sec
: On : Off
B
Image 12-1
L Status Led
C
D
Image 12-2
A Power standby
B The power is on (Normal condition)
C Abnormal
(The lamp replacement message is displayed or the protection circuit is working. Turn the projector off and consult
your dealer.)
D
• When the lamp is illuminating, it is in the warmup mode. (You cannot turn off the power.)
• When the lamp is off, it is in the cooling mode. (You cannot turn on the power.)
106 R5905597 PHXX SERIES 16/10/2013

13. Specifications
13. SPECIFICATIONS
13.1 Specifications of PHXG-91B

Overview
Projector type XGA single-chip DLP projector
Technology 0.70" DMD
Color wheel 4S standard (RGBW)
Resolution 1,024 x 768 XGA
Brightness 8,500 ANSI lumens / 6,200 ANSI lumens (eco-mode) (complies with ISO 21118)
Contrast ratio 2,800:1
Brightness uniformity 70%
Aspect Ratio 4:3
ScenergiX Yes
Lens type H lens
Lenses 1.7-2.3:1; 0.8-1.0:1; 1.3-1.8:1; 2.2-2.9:1; 2.9-4.7:1; 4.7-9.0:1
Optical lens shift Vertical: -0% to +118% / horizontal: -20% to +20%
Color correction Yes
Lamps 2 x 350W AC lamp
Lamp lifetime Up to 2,000 hours (full power) / Up to 4,000 hours (eco mode)
Sealed DLP™ core Yes
Optical dowser Yes
Advance Picture in Picture PIP
Orientation table - ceiling
WARP Yes
Integrated web server Yes
Keystone correction Yes
Inputs 5 BNC (RGBHV, component), S-VIDEO, D-SUB 15-pin, HDMI, DVI-D (HDCP)
Input Resolutions up to WUXGA (1,920 x 1,200) 60Hz
Software tools Projector Toolset
Control IR, RS232, RJ45
Network connection 10/100 base-T, RJ-45 connection
Power requirements 100-240V / 50-60Hz
Max. power consumption 910W / 690W(eco mode) / 0.3W (standby)
Noise level (typical at 25°C/77°F) 44 dBA (bright mode) / 39 dBA (eco mode)
Operational ambient temperature 5-40°C / 41°-104°F
Operational humidity 30-90%
Dimensions (WxLxH) 510 x 660 x 263 mm
Weight 21kg
Shipping dimensions (WxLxH) 650 x 840 x 415 mm
Shipping Weight from Factory 26.5 kg
Certifications CB test certificate, US emc, US safety, CE emc and safety, CCC emc and safety
Warranty 3 years standard warranty (contact your local sales rep for details per region)
R5905597 PHXX SERIES 16/10/2013 107

13. Specifications
13.2 Specifications of PHWX-81B

Overview
Projector type WXGA single-chip DLP projector
Resolution 1,280 x 800 WXGA
Brightness 7,300 ANSI lumens / 5,300 ANSI lumens (eco-mode) (compliant with ISO 21118)
Aspect Ratio 16:10
ScenergiX Yes
Lens type H lens
Lenses 1.7-2.3:1; 0.8-1.0:1; 1.4-1.9:1; 2.3-2.9:1; 2.9-4.8:1; 4.8-9.2:1
Optical dowser Yes
Advance Picture in Picture Split
WARP Yes
Inputs 5 BNC (RGBHV, component), S-VIDEO, D-SUB 15-pin, HDMI, DVI-D (HDCP)
Noise level (typical at 25°C/77°F) 44 dBA (bright mode) / 39 dBA (eco mode)
Weight 21kg
Warranty 3 years standard warranty (warranty and service conditions can differ from region to
region. Contact your local sales or service rep for more details)
108 R5905597 PHXX SERIES 16/10/2013

13. Specifications
13.3 Specifications of PHWU-81B

Overview
Projector type WUXGA single-chip DLP projector
Resolution 1,920 x 1200 WUXGA
Brightness 7,500 ANSI lumens / 5,450 ANSI lumens (eco-mode)(compliant with ISO 21118)
Aspect Ratio 16:10
ScenergiX Yes
Lens type H lens
Lenses 1.7-2.3:1; 0.8-1.0:1; 1.3-1.8:1; 2.2-2.7:1; 2.8-4.5:1; 4.5-8.7:1
Optical dowser Yes
Advance Picture in Picture Split
WARP Yes
Inputs 5 BNC (RGBHV, component), S-VIDEO, D-SUB 15-pin, HDMI, DVI-D (HDCP), SDI
Noise level (typical at 25°C/77°F) 44 dBA (bright mode)/ 39 dBA (eco mode)
Weight 21kg
Warranty 3 years standard warranty (conditions can differ from region to region. Contact your
local sales or service rep for more details)
R5905597 PHXX SERIES 16/10/2013 109

13. Specifications
13.4 Specification of RGB signals in each computer mode of the projector For
PHWU-81B
Overview
Signal mode Resolution Horizon- Verti- Normal mode Native mode Plug and Play4
tal fre- cal fre-
(H x V) quency quency (H x V) (H x V) COM- COM- HDMI IN
PUTER/ PUTER terminal
(kHz) (Hz) COMPO- / COM-
NENT PONENT
VIDEO DVI-D IN
IN-1 ter- (HDCP)
minal terminal
TV60, 480i 720 x 480 15.73 59.94 1600 x 1200 -
(525i)56
TV50, 576i 720 x 576 15.63 50.00 1600 x 1200 -
(625i)56
1080i60 1920 x 1080 33.75 60.00 1920 x 1080 - x x
(1125i60)5
1080i50 1920 x 1080 28.13 50.00 1920 x 1080 - x x
(1125i50)5
480p (525p)5 720 x 480 31.47 59.94 1600 x 1200 - x x
576p (625p)5 720 x 576 31.25 50.00 1600 x 1200 - x x
720p60 1280 x 720 45.00 60.00 1920 x 1080 - x x

(750p60)5
720p60 1280 x 720 37.50 50.00 1920 x 1080 - x x
(750p50)5
1080p60 1920 x 1080 67.50 60.00 1920 x 1080 - x x
(1125p60)5
1080p50 1920 x 1080 56.25 50.00 0 1920 x 1080 - x x
(1125p50)5
CGA70 640 x 400 31.47 70.09 1920 x 1200 640 x 400
CGA84 640 x 400 37.86 84.13 1920 x 1200 640 x 400
CGA85 640 x 400 37.86 85.08 1920 x 1200 640 x 400
VGA60 640 x 480 31.47 59.94 1600 x 1200 640 x 480 x x x
VGA72 640 x 480 37.86 72.81 1600 x 1200 640 x 480 x
VGA75 640 x 480 37.50 75.00 1600 x 1200 640 x 480 x
VGA85 640 x 480 43.27 85.01 1600 x 1200 640 x 480

SVGA56 800 x 600 35.16 56.25 1600 x 1200 800 x 600 x
SVGA60 800 x 600 37.88 60.32 1600 x 1200 800 x 600 x x x
SVGA72 800 x 600 48.08 72.19 1600 x 1200 800 x 600 x
SVGA75 800 x 600 46.88 75.00 1600 x 1200 800 x 600 x
SVGA85 800 x 600 53.67 85.06 1600 x 1200 800 x 600

SVGA95 800 x 600 59.97 94.89 1600 x 1200 800 x 600
XGA60 1024 x 768 48.36 60.00 1600 x 1200 1024 x 768 x x x
XGA70 1024 x 768 56.48 70.07 1600 x 1200 1024 x 768 x
XGA75 1024 x 768 60.02 75.03 1600 x 1200 1024 x 768 x
XGA85 1024 x 768 68.68 85.00 1600 x 1200 1024 x 768

SXGA70a 1152 x 864 63.85 70.01 1600 x 1200 1152 x 864
SXGA75a 1152 x 864 67.50 75.00 1600 x 1200 1152 x 864
SXGA85a 1152 x 864 77.49 85.06 1600 x 1200 1152 x 864
WXGA60 1280 x 768 47.78 59.87 1920 x 1152 1280 x 768 x x
4. Signals marked with x in the Plug and Play column are described in EDID (extended display identification data) of the projector.a
5. SPLIT in the INSTALLATION 1 menu doesn’t function with these signals.
6. COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) terminal and HDMI IN terminal aren’t supported.
110 R5905597 PHXX SERIES 16/10/2013

13. Specifications
WXGA60a 1280 x 800 49.70 59.81 1920 x 1200 1280 x 800 x x x
WXGA60b 1360 x 768 47.71 60.02 1920 x 1085 1360 x 768

WXGA60c 1366 x 768 47.71 59.79 1920 x 1080 1366 x 768 x x x
WXGA+60 1440 x 900 55.94 59.89 1920 x 1200 1440 x 900 x x x
WXGA++60 1600 x 900 60.00 60.00 1920 x 1080 1600 x 900

SXGA60b 1280 x 960 60.00 60.00 1600 x 1200 1280 x 960 x x x
SXGA75b 1280 x 960 75.00 75.00 1600 x 1200 1280 x 960

SXGA85b 1280 x 960 85.94 85.00 1600 x 1200 1280 x 960
SXGA60 1280 x 1024 63.98 60.02 1500 x 1200 1280 x 1024 x x x
SXGA75 1280 x 1024 79.98 75.02 1500 x 1200 1280 x 1024 x
SXGA85 1280 x 1024 91.15 85.02 1500 x 1200 1280 x 1024

SXGA+60 1400 x 1050 63.98 60.02 1600 x 1200 1400 x 1050
1400 x 1050 65.32 59.98 1600 x 1200 1400 x 1050 x x x
SXGA+75 1400 x 1050 82.28 74.87 1600 x 1200 1400 x 1050

WSXGA+60 1680 x 1050 65.29 59.95 1920 x 1200 1680 x 1050
MAC13 640 x 480 35.00 66.67 1600 x 1200 640 x 480 x
MAC16 832 x 624 49.72 74.55 4 1600 x 1200 832 x 62 x
MAC19 1024 x 768 60.24 75.02 1600 x 1200 1024 x 768

HP75 1024 x 768 62.94 74.92 1600 x 1200 1024 x 768
HP72 1280 x 1024 78.13 72.00 1500 x 1200 1280 x 1024
SUN66a 1152 x 900 61.85 66.00 1536 x 1200 1152 x 900
SUN76a 1152 x 900 71.81 76.64 1536 x 1200 1152 x 900
SUN66 1280 x 1024 71.68 66.68 1500 x 1200 1280 x 1024
SUN76 1280 x 1024 81.13 76.11 1500 x 1200 1280 x 1024
SGI72 1280 x 1024 76.92 72.30 1500 x 1200 1280 x 1024
SGI76 1280 x 1024 82.01 76.00 1500 x 1200 1280 x 1024

UXGA60 1600 x 1200 75.00 60.00 1600 x 1200 1600 x 1200 x x x
WUXGA60 1920 x 1200 74.04 59.95 1920 x 1200 1920 x 1200 x x x
Signals described in the Signal mode column can be input regardless of the x mark in the Plug and Play column. For signals not
marked with x in the Plug and Play column, the resolution may not be supported even when it is supported on the computer.
13.5 Specification of RGB signals in each computer mode of the projector, For
PHWX-81B
Overview
Signal mode Resolution Horizon- Verti- Normal mode Native mode Plug and Play7
tal fre- cal fre-
(H x V) quency quency (H x V) (H x V) COM- COM- HDMI IN
PUTER/ PUTER terminal
(kHz) (Hz) COMPO- / COM-
NENT PONENT
VIDEO DVI-D IN
IN-1 ter- (HDCP)
minal terminal
TV60, 480i 720 x 480 15.73 59.94 1066 x 800 -
(525i)56
TV50, 576i 720 x 576 15.63 50.00 1066 x 800 -
(625i)56
R5905597 PHXX SERIES 16/10/2013 111

13. Specifications
1080i60 1920 x 1080 33.75 60.00 1280 x 720 - x x

(1125i60)5
1080i50 1920 x 1080 28.13 50.00 1280 x 720 - x x
(1125i50)5
480p (525p)5 720 x 480 31.47 59.94 1280 x 720 - x x
576p (625p)5 720 x 576 31.25 50.00 1280 x 720 - x x
720p60 1280 x 720 45.00 60.00 1280 x 720 - x x

(750p60)5
720p60 1280 x 720 37.50 50.00 1280 x 720 - x x
(750p50)5
1080p60 1920 x 1080 67.50 60.00 1920 x 1080 - x x
(1125p60)5
1080p50 1920 x 1080 56.25 50.00 0 1280 x 720 - x x
(1125p50)5
CGA70 640 x 400 31.47 70.09 1280 x 800 640 x 400
CGA84 640 x 400 37.86 84.13 1280 x 800 640 x 400
CGA85 640 x 400 37.86 85.08 1280 x 800 640 x 400
VGA60 640 x 480 31.47 59.94 1066 x 800 640 x 480 x x x
VGA72 640 x 480 37.86 72.81 1066 x 800 640 x 480 x
VGA75 640 x 480 37.50 75.00 1066 x 800 640 x 480 x
VGA85 640 x 480 43.27 85.01 1066 x 800 640 x 480

SVGA56 800 x 600 35.16 56.25 1066 x 800 800 x 600 x
SVGA60 800 x 600 37.88 60.32 1066 x 800 800 x 600 x x x
SVGA72 800 x 600 48.08 72.19 1066 x 800 800 x 600 x
SVGA75 800 x 600 46.88 75.00 1066 x 800 800 x 600 x
SVGA85 800 x 600 53.67 85.06 1066 x 800 800 x 600

SVGA95 800 x 600 59.97 94.89 1066 x 800 800 x 600
XGA60 1024 x 768 48.36 60.00 1066 x 800 1024 x 768 x x x
XGA70 1024 x 768 56.48 70.07 1066 x 800 1024 x 768 x
XGA75 1024 x 768 60.02 75.03 1066 x 800 1024 x 768 x
XGA85 1024 x 768 68.68 85.00 1066 x 800 1024 x 768

SXGA70a 1152 x 864 63.85 70.01 1066 x 800 1152 x 800
SXGA75a 1152 x 864 67.50 75.00 1066 x 800 1152 x 800
SXGA85a 1152 x 864 77.49 85.06 1066 x 800 1152 x 800
WXGA60 1280 x 768 47.78 59.87 1066 x 800 1280 x 768 x x
WXGA60a 1280 x 800 49.70 59.81 1066 x 800 1280 x 800 x x x
WXGA60b 1360 x 768 47.71 60.02 1280 x 723 1280 x 768

WXGA60c 1366 x 768 47.71 59.79 1280 x 720 1280 x 768 x x x
WXGA+60 1440 x 900 55.94 59.89 1280 x 800 1280 x 800 x x x
WXGA++60 1600 x 900 60.00 60.00 1280 x 720 1280 x 800

SXGA60b 1280 x 960 60.00 60.00 1066 x 800 1280 x 800 x x x
SXGA75b 1280 x 960 75.00 75.00 1066 x 800 1280 x 800

SXGA85b 1280 x 960 85.94 85.00 1066 x 800 1280 x 800
SXGA60 1280 x 1024 63.98 60.02 1000 x 800 1280 x 800 x x x
SXGA75 1280 x 1024 79.98 75.02 1000 x 800 1280 x 800 x
SXGA85 1280 x 1024 91.15 85.02 1000 x 800 1280 x 800

SXGA+60 1400 x 1050 63.98 60.02 1066 x 800 1280 x 800
1400 x 1050 65.32 59.98 1066 x 800 1280 x 800 x x x
SXGA+75 1400 x 1050 82.28 74.87 1066 x 800 1280 x 800

WSXGA+60 1680 x 1050 65.29 59.95 1066 x 800 1280 x 800
112 R5905597 PHXX SERIES 16/10/2013

13. Specifications
MAC13 640 x 480 35.00 66.67 1066 x 800 640 x 480 x
MAC16 832 x 624 49.72 74.55 4 1066 x 800 832 x 62 x
MAC19 1024 x 768 60.24 75.02 1066 x 800 1024 x 768

HP75 1024 x 768 62.94 74.92 1066 x 800 1024 x 768
HP72 1280 x 1024 78.13 72.00 1000 x 800 1280 x 1024
SUN66a 1152 x 900 61.85 66.00 1024 x 800 1152 x 800
SUN76a 1152 x 900 71.81 76.64 1024 x 800 1152 x 800
SUN66 1280 x 1024 71.68 66.68 1000 x 800 1280 x 800
SUN76 1280 x 1024 81.13 76.11 1000 x 800 1280 x 800
SGI72 1280 x 1024 76.92 72.30 1000 x 800 1280 x 800
SGI76 1280 x 1024 82.01 76.00 1000 x 800 1280 x 800

UXGA60 1600 x 1200 75.00 60.00 1066 x 800 1280 x 800 x x x
WUXGA60 1920 x 1200 74.04 59.95 1280 x 800 1280 x 800
13.6 Specification of RGB signals in each computer mode of the projector, For
PHWX-81B
Overview
Signal mode Resolution Horizontal Verti- Normal mode Plug and Play8
frequency cal fre-
(H x V) quency (H x V) COM- COM- HDMI IN
(kHz) PUTER/ PUTER terminal
(Hz) COMPO- / COM-
NENT PONENT
VIDEO IN-1 DVI-D IN
terminal (HDCP) ter-
minal
TV60, 480i 720 x 480 15.73 59.94 1024 x 768
(525i)56
TV50, 576i 720 x 576 15.63 50.00 1024 x 768
(625i)56
1080i60 1920 x 1080 33.75 60.00 1024 x 576 x x
(1125i60)5
1080i50 1920 x 1080 28.13 50.00 1024 x 576 x x
(1125i50)5
480p (525p)5 720 x 480 31.47 59.94 1024 x 768 x x
576p (625p)5 720 x 576 31.25 50.00 1024 x 768 x x
720p60 1280 x 720 45.00 60.00 1024 x 576 x x

(750p60)5
720p60 1280 x 720 37.50 50.00 1024 x 576 x x
(750p50)5
1080p60 1920 x 1080 67.50 60.00 1024 x 576 x x
(1125p60)5
1080p50 1920 x 1080 56.25 50.00 0 1024 x 576 x x
(1125p50)5
CGA70 640 x 400 31.47 70.09 1024 x 640
CGA84 640 x 400 37.86 84.13 1024 x 640
CGA85 640 x 400 37.86 85.08 1024 x 640
VGA60 640 x 480 31.47 59.94 1024 x 768 x x x
VGA72 640 x 480 37.86 72.81 1024 x 768 x
R5905597 PHXX SERIES 16/10/2013 113

13. Specifications
VGA75 640 x 480 37.50 75.00 1024 x 768 x
VGA85 640 x 480 43.27 85.01 1024 x 768

SVGA56 800 x 600 35.16 56.25 1024 x 768 x
SVGA60 800 x 600 37.88 60.32 1024 x 768 x x x
SVGA72 800 x 600 48.08 72.19 1024 x 768 x
SVGA75 800 x 600 46.88 75.00 1024 x 768 x
SVGA85 800 x 600 53.67 85.06 1024 x 768

SVGA95 800 x 600 59.97 94.89 1024 x 768
XGA60 1024 x 768 48.36 60.00 1024 x 768 x x x
XGA70 1024 x 768 56.48 70.07 1024 x 768 x
XGA75 1024 x 768 60.02 75.03 1024 x 768 x
XGA85 1024 x 768 68.68 85.00 1024 x 768

SXGA70a 1152 x 864 63.85 70.01 1024 x 768
SXGA75a 1152 x 864 67.50 75.00 1024 x 768
SXGA85a 1152 x 864 77.49 85.06 1024 x 768
WXGA60 1280 x 768 47.78 59.87 1024 x 615 x x
WXGA60a 1280 x 800 49.70 59.81 1024 x 640 x x x
WXGA60b 1360 x 768 47.71 60.02 1024 x 579

WXGA60c 1366 x 768 47.71 59.79 1024 x 576 x x x
WXGA+60 1440 x 900 55.94 59.89 1024 x 640 x x x
WXGA++60 1600 x 900 60.00 60.00 1024 x 576

SXGA60b 1280 x 960 60.00 60.00 1024 x 768 x x x
SXGA75b 1280 x 960 75.00 75.00 1024 x 768

SXGA85b 1280 x 960 85.94 85.00 1024 x 768
SXGA60 1280 x 1024 63.98 60.02 960 x 768 x x x
SXGA75 1280 x 1024 79.98 75.02 960 x 768 x
SXGA85 1280 x 1024 91.15 85.02 960 x 768

SXGA+60 1400 x 1050 63.98 60.02 960 x 768
1400 x 1050 65.32 59.98 1024 x 768 x x x
SXGA+75 1400 x 1050 82.28 74.87 1024 x 768

WSXGA+60 1680 x 1050 65.29 59.95 1024 x 640
MAC13 640 x 480 35.00 66.67 1024 x 768 x
MAC16 832 x 624 49.72 74.55 4 1024 x 768 x
MAC19 1024 x 768 60.24 75.02 1024 x 768

HP75 1024 x 768 62.94 74.92 1024 x 768
HP72 1280 x 1024 78.13 72.00 960 x 768
SUN66a 1152 x 900 61.85 66.00 983 x 768
SUN76a 1152 x 900 71.81 76.64 983 x 768
SUN66 1280 x 1024 71.68 66.68 960 x 768
SUN76 1280 x 1024 81.13 76.11 960 x 768
SGI72 1280 x 1024 76.92 72.30 960 x 768
SGI76 1280 x 1024 82.01 76.00 960 x 768

UXGA60 1600 x 1200 75.00 60.00 1024 x 768 x x x
WUXGA60 1920 x 1200 74.04 59.95 1024 x 640
114 R5905597 PHXX SERIES 16/10/2013

13. Specifications
13.7 Specification of RGB signals in each computer mode of the projector

Important
• Some computers aren’t compatible with the projector.
• The projector’s maximum resolution is 1920 x 1200 pixels (PHWU-81B), 1280 x 800 pixels (PHWX- 81B), or 1024 x 768 pixels
(PHXG-91B). It may not display images of higher resolutions than its maximum resolution correctly.
• Images with SYNC on G (Green) signal may jitter.
• Images with SYNC on G (Green) signal may be tinged with green
• If the resolution and frequency of your computer aren’t shown on the table, find the compatible resolution and frequency by
changing the resolution of your computer.
• TV60 and TV50 are equivalent to 480i and 576i respectively. When these signals are supplied to the VIDEO IN or S-VIDEO IN
terminal, the signal mode is indicated as TV60 or TV50. When they are supplied to the COMPUTER/COMPONENT VIDEO IN
terminals, the signal mode is indicated as 480i or 576i.
• This projector doesn’t support 480p signals from video devices having 4 lines (R, G, B, CS*) or having 5 lines (R, G, B, H, V).‚-
NATIVE mode (for PHWU-81B/PHWX-81B only)

When moire patterns or lines of uneven thickness appear on the projected image, these symptoms may be improved by displaying
it in its original image size (NATIVE mode). To display the image in the NATIVE mode, set ASPECT of the SIGNAL menu to NA-
TIVE.12691
• For signals that are larger than the panel resolution, only their center part is displayed in the NATIVE mode. The area exceeding
the panel resolution isn’t displaye
• In the NATIVE mode, images are black-framed when the image resolution is lower than the panel resolution.
• In the NATIVE mode, some signals may be displayed with a black frame even when they have a higher resolution than the
panel resolution.
Available signal system for SDI (for PHWU-81B only)

SD-SDI 480i
576i
HD-SDI 720/50p
720/60p
1080/50i
1080/60i
1080/24p
3G-SDI 1080/50p
1080/60p
The signal format supports 1/1.001.
R5905597 PHXX SERIES 16/10/2013 115

13. Specifications
13.8 Dimensions
Overview
342
30
192
Holes for hanger
169 (M4 Depth 10 : 4 places)
51
240
340
263
119 *
Ø46.6 314 70
510 660
Image 13-1
* = factory defaults
13.9 Connectors
SERIAL IN/OUT (D-SUB 9-pin) 5 1
5 1
9 6
Image 13-2
Pin No. Name I/O

1 - -
2 TXD IN
3 RXD OUT
4 - -
5 GND -
6 - -
7 - -
8 - -
9 - -
COMPUTER/COMPONENT VIDEO IN-1 (Mini D-SUB 15-pin)

5 1
10 6
15 11
Image 13-3
Pin No. Spec

1 R(RED)/PR/CR
2 G(GREEN)/Ye
116 R5905597 PHXX SERIES 16/10/2013

13. Specifications
Pin No. Spec

3 B(BLUE)/PB/CB
4 GND
5 GND
6 GND
7 GND
8 GND
9 DDC 5V
10 GND
11 GND
12 DDC Data
13 HD/CS
14 VD
15 DDC Clock
COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) (DVI-D 24-pin)

24 17
16 9
8 1
Image 13-4
Pin No. Spec

1 TMDS DATA 2-
2 TMDS DATA 2+
3 TMDS DATA 2 Shield
4 -
5 -
6 DDC Clock
7 DDC Data
8 -
9 TMDS DATA 1-
10 TMDS DATA 1+
12 -
13 -
14 +5V Power
15 Ground (for +5V)
16 Hot plug detection
17 TMDS DATA 0-
18 TMDS DATA 0+
20 -
21 -
22 TMDS Clock Shield

23 TMDS Clock+
24 TMDS Clock-
R5905597 PHXX SERIES 16/10/2013 117

13. Specifications
HDMI IN (HDMI connector)

1 19
2 18
Image 13-5
Pin No. Spec

1 TMDS DATA 2+
3 TMDS DATA 2-
4 TMDS DATA 1+
6 TMDS DATA 1-
7 TMDS DATA 0+
9 TMDS DATA 0-
10 TMDS Clock+
11 TMDS Clock Shield
12 TMDS Clock-
13 CED
14 -
15 SCL
16 SDA
17 DCC Ground
18 +5V Power
19 Hot Plug Detection
118 R5905597 PHXX SERIES 16/10/2013

A. Option lens H LENS 0.8-1.0, 2.8-4.5 or 4.5-8.7
A. OPTION LENS H LENS 0.8-1.0, 2.8-4.5 OR 4.5-8.7
CAUTION: Lens mounting must be performed by service personnel.
A.1 Lens mounting procedure

Preparation
Check that the lens shift is at the factory default position (or the lens shift reset position) before mounting the option lens.
Be sure to turn off the projector and unplug the power cord from the wall outlet before mounting the option lens.
When you have any inquiries, contact your dealer.
How to mount
(c)
(b)
(a)
(c)
(b)
(a)
Image A-1
Side cover removal

3. Remove the six screws (c) securing the Top cover. (There are three screws each on the left and right.)
Release the Top cover in the direction of the arrow (d) from the unit.
T
(d)
(c) (c)
(c)
Image A-2
Top cover removal
T Top cover
4. Release the connector (e) for the zoom/focus motor of the standard lens.
R5905597 PHXX SERIES 16/10/2013 119

(g)
(f ) (e)
C
(h)
O
Image A-3
Lens removal
C Lens caps
O Optional lens
5. While holding down the lock button (f), slightly turn the fixed ring (g) counterclockwise to release the lock.
6. While holding the lens to prevent it from falling, turn the fixed ring (g) fully counterclockwise to unlock the lens.
7. Remove the standard lens in the arrow’s direction.
8. Attach the option lens in the arrow’s direction so that the motors (h) are positioned as shown by the figure. (Remove the lens
caps before attaching the option lens.)
9. Turn the fixed ring (g) until it is put into place (and the lock button (f) clicks into place) to secure it.
R E
F
C
Image A-4
R Reference line
E Edge scale
F Focus correction ring
C Center scale
10.Lock the connector for the zoom/focus motor of the option lens.
11. Mount the top cover in the reverse order of removal.
12.Mount the side cover of the left and right in the reverse order of removal.
A.2 Focus correction function
Only for H LENS 0.8-1.0
What can be done?

H LENS 0.8-1.0 has the focus correction function that corrects the focus balance at and around the center of the screen.
Focus correction procedure

1. Align the center scale of the focus correction ring with the reference line.
2. Adjust the screen focus using the projector.
Normally, the screen focus is adjusted properly using the procedure described above. However, the focus balance at and around
the center of the screen may be different depending on the characteristics of the lens and the projector. In such a case, following
the procedure described below may improve the symptom.
Improvement procedure
1. Turn the focus correction ring clockwise or counterclockwise manually and align the edge scale with the reference line.2
2. Adjust the screen focus using the projector.
120 R5905597 PHXX SERIES 16/10/2013

A.3 Check after mounting the lens

Overview
After replacing the lens, be sure to check the following for ensuring safety.
• Check that the connector for the zoom/focus motor is locked securely.
• Check that no lead wires are caught in mechanical parts.
Cautions after mounting

• Do not transport the projector with the option lens mounted. The projector may be damaged.
• With the option lens mounted, the brightness, resolution, and color uniformity in the projected image may differ from those with
the standard lens.
• With the option lens mounted, the adjustable angle in the keystone adjustment differs from that with the standard lens.
• In the keystone adjustment with the option lens mounted, the proper aspect ratio may not be obtained.
• Projected images may become distorted, have decreased resolution, or have shadows at their corners if they are positioned
close to the top (or bottom in the case of a ceiling-mount projector) or right or left edge of the effective projection area shown
on the right.
• For details about ZOOM/FOCUS adjustment and LENS SHIFT LOCK, see User Manual of the projector.
Be careful not to caught in the opening in the lens while the lens is moving.
A.4 Cleaning of the lens

Overview
Remove dust or dirt using the commercially available lens care products (such as cleaning paper or cloth for lens and blower brush).
• Since the lens surface is sensitive, do not scrub it with a solid object or tap on it.
• Do not wipe the lens with lens cleaner or solvent containing alcohol. Doing so may cause wipe marks or peel off the lens coating
and the focus performance may be affected.
• Make sure to clean the lens after the lamp is turned off and the lens is cooled sufficiently.
A.5 Specifications H LENS 0.8-1.0

General
F No. : F24
Focal distance : f=11.4-14.2 mm
Zoom/focus : electrical drive
W1 W W1 W1 W W1
C
H2
H1
C
H
H0
H0
H
H1
L L
H2
L
A A
I II
Image A-5
R5905597 PHXX SERIES 16/10/2013 121

I Fornt projection
XGA model with H LENS 0.8-1.0

The numbers are approximate and may be slightly different from the actual measurements.
Screen size (4:3) Projector distance (L) Lens shift height9 Lens shift
width
Diagonal size Width (W) Height (H) Shorter Longest (Tele) Movement Movement Movement
(Wide) distance (H1) distance (H2) distance (W1)
inch cm inc cm inch cm inch m inch m inch cm inch cm inch cm
40 102 32 81 24 61 25 0.6 31 0.8 12 30 2 6 3 8

60 152 48 122 36 91 38 1.0 47 1.2 18 46 3 9 5 12
80 203 64 163 48 122 51 1.3 64 1.6 24 61 4 11 6 16
100 254 80 203 60 152 64 1.6 80 2.0 30 76 6 14 8 20
150 381 120 305 90 229 96 2.4 120 3.1 45 114 8 21 12 30
200 508 160 406 120 305 128 3.3 161 4.1 60 152 11 28 16 41
250 635 200 508 150 381 161 4.1 201 5.1 75 191 14 36 20 51
300 762 240 610 180 457 193 4.9 242 6.1 90 229 17 43 24 61
WXGA model with H LENS 0.8-1.0

width
40 102 34 86 21 54 27 0.7 34 0.9 10 25 5 12 3 9

60 152 51 129 32 81 41 1.0 51 1.3 15 37 7 17 5 13
80 203 68 172 42 108 55 1.4 68 1.7 19 49 9 23 7 17
100 254 85 215 53 135 68 1.7 86 2.2 24 62 11 29 9 22
150 381 127 323 79 202 103 2.6 129 3.3 36 92 17 43 13 33
200 508 170 431 106 269 138 3.5 173 4.4 49 123 23 58 17 44
250 635 212 538 132 337 173 4.4 216 5.5 61 154 28 72 21 55
300 762 254 646 159 404 208 5.3 260 6.6 73 185 34 86 26 65
WUXGA model with H LENS 0.8-1.0

width
40 102 34 86 21 54 25 0.6 32 0.8 10 26 4 10 3 8

60 152 51 129 32 81 39 1.0 49 1.2 15 39 6 15 5 12
80 203 68 172 42 108 52 1.3 65 1.7 21 52 8 20 7 17
100 254 85 215 53 135 65 1.7 82 2.1 26 66 10 25 8 21
150 381 127 323 79 202 98 2.5 123 3.1 39 98 15 37 12 31
200 508 170 431 106 269 131 3.3 165 4.2 52 131 20 50 16 42
9. The lens shift height and width show distances from the factory default position.
122 R5905597 PHXX SERIES 16/10/2013

250 635 212 538 132 337 165 4.2 206 5.2 65 164 24 62 20 52
300 762 254 646 159 404 198 5.0 248 6.3 77 197 29 75 25 62

General
F No. : F2.2-2.7
W1 W W1 W1 W W1
C
H2
H1
C
H
H0
H0
H
H1
L L
H2
L
A A
I II
Image A-6
I Fornt projection

width
(W1)
40 102 32 81 24 61 - - 148 3.8 12 30 2 6 3 8

60 152 48 122 36 91 136 3.5 224 5.7 18 46 3 9 5 12
80 203 64 163 48 122 183 4.7 301 7.6 24 61 4 11 6 16
100 254 80 203 60 152 230 5.8 377 9.630 9.6 76 6 14 8 20
150 381 120 305 90 229 348 8.8 568 14.4 45 114 8 21 12 30
200 508 160 406 120 305 465 11.8 759 19.3 60 152 11 28 16 41
250 635 200 508 150 381 583 14.8 951 24.1 75 191 14 36 20 51
300 762 240 610 180 457 701 17.8 1142 29.0 90 229 17 43 24 61

width
(W1)
R5905597 PHXX SERIES 16/10/2013 123

width
(W1)
40 102 34 86 21 54 - - 159 4.0 10 25 5 12 3 9
60 152 51 129 32 81 147 3.7 241 6.1 15 37 7 17 5 13
80 203 68 172 42 108 197 5.0 323 8.2 19 49 9 23 7 17
100 254 85 215 53 135 248 6.3 406 10.3 24 62 11 29 9 22
150 381 127 323 79 202 374 9.5 611 15.5 36 92 17 43 13 33
200 508 170 431 106 269 500 12.7 816 20.7 49 123 23 58 17 44
250 635 212 538 132 337 627 15.9 1021 25.9 61 154 28 72 21 55
300 762 254 646 159 404 753 19.1 1227 31.2 73 185 34 86 26 65

width
(W1)
40 102 34 86 21 54 - - 151 3.8 10 26 4 10 3 8

60 152 51 129 32 81 139 3.5 229 5.8 15 39 6 15 5 12
80 203 68 172 42 108 187 4.8 308 7.8 21 52 8 20 7 17
100 254 85 215 53 135 235 6.0 386 9.8 26 66 10 25 8 21
150 381 127 323 79 202 355 9.0 581 14.8 39 98 15 37 12 31
200 508 170 431 106 269 475 12.1 776 19.7 52 131 20 50 16 42
250 635 212 538 132 337 595 15.1 972 24.7 65 164 24 62 20 52
300 762 254 646 159 404 716 18.2 1167 29.6 77 197 29 75 25 6

General
F No. : F2.8
124 R5905597 PHXX SERIES 16/10/2013

W1 W W1 W1 W W1
C
H2
H1
C
H
H0
H0
H
H1
L L
H2
L
L
A A
I II
Image A-7
I Fornt projection

width
(W1)
60 152 48 122 36 91 229 5.8 437 11.1 18 46 3 9 5 12

80 203 64 163 48 122 302 7.7 581 14.8 24 61 4 11 6 16
100 254 80 203 60 152 376 9.5 724 18.4 30 76 6 14 8 20
150 381 120 305 90 229 560 14.2 1082 27.5 45 114 8 21 12 30
200 508 160 406 120 305 744 18.9 1440 36.6 60 152 11 28 16 41
250 635 200 508 150 381 928 23.6 - - 75 191 14 36 20 51
300 762 240 610 180 457 1113 28.3 - - 90 229 17 43 24 61

width
(W1)
60 152 51 129 32 81 245 6.2 469 11.9 15 37 7 17 5 13

80 203 68 172 42 108 324 8.2 623 15.8 19 49 9 23 7 17
100 254 85 215 53 135 403 10.2 777 19.7 24 62 11 29 9 22
150 381 127 323 79 202 601 15.3 1162 29.5 36 92 17 43 13 33
200 508 170 431 106 269 799 20.3 1547 39.3 49 123 23 58 17 44
250 635 212 538 132 337 997 25.3 - - 61 154 28 72 21 55
300 762 254 646 159 404 1194 30.3 - - 73 185 34 86 26 65
R5905597 PHXX SERIES 16/10/2013 125


width
Diagonal Width (W) Height (H) Shorter Longest Movement Movement Movement
(W1)
60 152 51 129 32 81 234 5.9 447 11.4 15 39 6 15 5 12

80 203 68 172 42 108 309 7.8 594 15.1 21 52 8 20 7 17
100 254 85 215 53 135 384 9.8 740 18.8 26 66 10 25 8 21
150 381 127 323 79 202 573 14.5 1107 28.1 39 98 15 37 12 31
200 508 170 431 106 269 761 19.3 1473 37.4 52 131 20 50 16 42
250 635 212 538 132 337 950 24.1 - - 65 164 24 62 20 52
300 762 254 646 159 404 1138 28.9 - - 77 197 29 75 25 62
126 R5905597 PHXX SERIES 16/10/2013

B. Optional lens H LENS 1.3-1.8
B. OPTIONAL LENS H LENS 1.3-1.8
CAUTION: Lens mounting must be performed by service personnel.
B.1 Lens mounting procedure

Preparation
Be sure to turn off the projector and unplug the power cord from the wall outlet before mounting the option lens.
When you have any inquiries, contact your dealer.
How to mount
1. Remove the lens cover.
M3 x 8
W O
Image B-1
L Lens cover
W Wire and eyelet
C Lens caps
O option lens
2. Fit the wire and eyelet of the option lens to the projector using the attached screw.
This prevents the option lens from dropping.
3. Remove the lens caps of the option lens.
4. Mount the option lens to the standard lens turning it clockwise.
Note: Protect your eyes and face from the swinging wire when mounting the option lens.
R5905597 PHXX SERIES 16/10/2013 127

Cautions after mounting

• Do not transport the projector with the option lens mounted. The projector may be damaged.
• With the option lens mounted, the brightness, resolution, and color uniformity in the projected image may differ from those with
the standard lens.
• With the option lens mounted, the adjustable angle in the keystone adjustment differs from that with the standard lens.
• In the keystone adjustment with the option lens mounted, the proper aspect ratio may not be obtained.
• Projected images may become distorted, have decreased resolution, or have shadows at their corners if they are positioned
close to the top (or bottom in the case of a ceiling-mount projector) or right or left edge of the effective projection area shown
on the right.
• For details about ZOOM/FOCUS adjustment and LENS SHIFT LOCK, see User Manual of the projector.
Be careful not to caught in the opening in the lens while the lens is moving.
B.2 Specifications H LENS 1.3-1.8

General
F No. : F2.0-2.4
W1 W W1 W1 W W1
C
H2
H1
C
H
H0
H0
H
H1
L L
H2
L
A A
I II
Image B-2
I Fornt projection

width
(W1)
40 102 32 81 24 61 41 1.0 57 1.5 12 30 2 6 3 8

60 152 48 122 36 91 63 1.6 88 2.2 18 46 3 9 5 12
80 203 64 163 48 122 86 2.2 118 3.0 24 61 4 11 6 16
100 254 80 203 60 152 108 2.7 148 3.8 30 76 6 14 8 20
150 381 120 305 90 229 164 4.2 224 5.7 45 114 8 21 12 30
128 R5905597 PHXX SERIES 16/10/2013

width
(W1)
200 508 160 406 120 305 219 5.6 300 7.6 60 152 11 28 16 41
250 635 200 508 150 381 275 7.0 - - 75 191 14 36 20 51
300 762 240 610 180 457 331 8.4 - - 90 229 17 43 24 61

width
(W1)
40 102 34 86 21 54 44 1.1 62 1.6 10 25 5 12 3 9

60 152 51 129 32 81 68 1.7 94 2.4 15 37 7 17 5 13
80 203 68 172 42 108 92 2.3 127 3.2 19 49 9 23 7 17
100 254 85 215 53 135 116 3.0 160 4.1 24 62 11 29 9 22
150 381 127 323 79 202 176 4.5 241 6.1 36 92 17 43 13 33
200 508 170 431 106 269 236 6.0 323 8.2 49 123 23 58 17 44
250 635 212 538 132 337 296 7.5 - - 61 154 28 72 21 55
300 762 254 646 159 404 356 9.0 - - 73 185 34 86 26 65

width
(W1)
40 102 34 86 21 54 42 1.1 59 1.5 10 26 4 10 3 8

60 152 51 129 32 81 65 1.6 90 2.3 15 39 6 15 5 12
80 203 68 172 42 108 87 2.2 121 3.1 21 52 8 20 7 17
100 254 85 215 53 135 110 2.8 152 3.9 26 66 10 25 8 21
150 381 127 323 79 202 167 4.2 229 5.8 39 98 15 37 12 31
200 508 170 431 106 269 224 5.7 307 7.8 52 131 20 50 16 42
250 635 212 538 132 337 281 7.1 - - 65 164 24 62 20 52
300 762 254 646 159 404 338 8.6 - - 77 197 29 75 25 62
B.3 Specifications H LENS 2.2-2.7

General
F No. : F2.1-2.4
R5905597 PHXX SERIES 16/10/2013 129

W1 W W1 W1 W W1
C
H2
H1
C
H
H0
H0
H
H1
L L
H2
L
L
A A
I II
Image B-3

width
Diagonal Width (W)10 Height (H) Shortest Longest Movement Movement Movement
(W1)
40 102 32 81 24 61 - - 88 2.2 12 30 2 6 3 8
60 152 48 122 36 91 105 2.7 135 3.4 18 46 3 9 5 12
80 203 64 163 48 122 142 3.6 182 4.6 24 61 4 11 6 16
100 254 80 203 60 152 180 4.6 228 5.8 30 76 6 14 8 20
150 381 120 305 90 229 273 6.9 345 8.8 45 114 8 21 12 30
200 508 160 406 120 305 366 9.3 462 11.7 60 152 11 28 16 41
250 635 200 508 150 381 459 11.7 579 14.7 75 191 14 36 20 51
300 762 240 610 180 457 553 14.0 696 17.7 90 229 17 43 24 61

width
(W1)
40 102 34 86 21 54 - - 95 2.4 10 25 5 12 3 9
60 152 51 129 32 81 113 2.9 145 3.7 15 37 7 17 5 13
80 203 68 172 42 108 153 3.9 196 5.0 19 49 9 23 7 17
100 254 85 215 53 135 193 4.9 246 6.2 24 62 11 29 9 22
150 381 127 323 79 202 294 7.5 371 9.4 36 92 17 43 13 33
200 508 170 431 106 269 394 10.0 497 12.6 49 123 23 58 17 44
250 635 212 538 132 337 494 12.5 623 15.8 61 154 28 72 21 55
300 762 254 646 159 404 594 15.1 748 19.0 73 185 34 86 26 65
130 R5905597 PHXX SERIES 16/10/2013


width
(W1)
40 102 34 86 21 54 - - 89 2.3 10 26 4 10 3 8
60 152 51 129 32 81 107 2.7 137 3.5 15 39 6 15 5 12
80 203 68 172 42 108 146 3.7 185 4.7 21 52 8 20 7 17
100 254 85 215 53 135 184 4.7 233 5.9 26 66 10 25 8 21
150 381 127 323 79 202 279 7.1 353 9.0 39 98 15 37 12 31
200 508 170 431 106 269 374 9.5 473 12.0 52 131 20 50 16 42
250 635 212 538 132 337 470 11.9 592 15.0 65 164 24 62 20 52
300 762 254 646 159 404 565 14.4 712 18.1 77 197 29 75 25 62
10. When the lens is set to wide to the full, the screen corners are shaded depending on the lens shift position.
R5905597 PHXX SERIES 16/10/2013 131

132 R5905597 PHXX SERIES 16/10/2013

C. Environmental information
C. ENVIRONMENTAL INFORMATION
C.1 Disposal information

Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and
electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible
harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste
and recycle them responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service.
For details, please visit the Barco website at: http://www.barco.com/en/AboutBarco/weee
Disposal of batteries in the product
This product contains batteries covered by the Directive 2006/66/EC which must be collected and disposed of separately
from municipal waste.
If the battery contains more than the specified values of lead (Pb), mercury (Hg) or cadmium (Cd), these chemical symbols will
appear below the crossed-out wheeled bin symbol.
By participating in separate collection of batteries, you will help to ensure proper disposal and to prevent potential negative effects
on the environment and human health.
C.2 Rohs compliance

Turkey RoHS compliance
Türkiye Cumhuriyeti: AEEE Yönetmeliğine Uygundur.

[Republic of Turkey: In conformity with the WEEE Regulation]
中国大陆 RoHS (Information for China ROHS compliance)

(1)电子信息产品污染控制标识 (3)根据包装回收标志(GB/T18455-2010) 根据2006/2/28公布的“电子信息产品污染控制管理办法”，
这个标记是适用于在中国销售的电子信息产品的环境保护使用期限。只要能遵守本产品在安全和使用方面的注意事项，从生产日
算起的年限以内，不会对环境污染，人体，财产产生深刻的影响。
10
注：此环境保护使用期限并不包含消耗品（电池等）。
产品正常使用终结废弃时，有关电子信息产品的回收、再利用等要遵守各自治体的法律法规的要求。
(2)含有有害6物质的名称，含有量，含有部品
本产品中所含有的有害6物质的名称，含有量，含有部品如下表所示。
产品中有毒有害物质或元素的名称及含量
R5905597 PHXX SERIES 16/10/2013 133

C. Environmental information
部件名称有毒有害物质或元素
铅 (Pb) 汞 (Hg) 镉 (Cd) 六价铬 (Cr(VI)) 多溴联苯 (PBB) 多溴二苯醚
(PBDE)
实装基板 x o o o o o
框架 x o o o o o
光学单元 x x o o o o
遥控器 x o o o o o
电缆类 x o o o o o
灯泡 x x o o o o
备注（○或×的表示意思）
○:表示该有毒有害物质在该部件所有均质材料中的含量均在SJ/T11363-2006标准规定的限量要求以下。
×:表示该有毒有害物质至少在该部件的某一均质材料中的含量超出SJ/T11363-2006标准规定的限量要求。
1. 零部件名称的“框架”，包括外部框架及内部构件。
(3)根据包装回收标志(GB/T18455-2010)
废弃包装器材时，有关包装器材的回收、再利用等请遵守地方自治体的相关法律法规的要求。
电池包装膜
随包装物品袋
缓冲材料
外包装箱 / 隔板
随包装物品带(CD-ROM袋)
产品包装膜
随包装物包装布
: 表面 : 背面
C.3 Production address

Factory
MITSUBISHI ELECTRIC CORPORATION, KYOTO WORKS
1 Zusho Baba, Nagaokakyo City,
Kyoto, 617-8550, Japan
134 R5905597 PHXX SERIES 16/10/2013

Glossary
GLOSSARY
Default Gateway
A server (or router) to communicate across networks (subnets) that are divided by Subnet Mask.
DHCP
Abbreviation for Dynamic Host Configuration Protocol. This protocol automatically assigns IP Address to networked devices.
IP Address
Numerical address to identify networked computers.
MAC Address
Abbreviation for Media Access Control Address. MAC Address is a unique ID number assigned to each network adapter. And this
is based on which data are sent and received between network adapters.
Subnet Mask
A numeric value to define the number of bits used for a network address of a divided network (or subnet) in an IP Address.
R5905597 PHXX SERIES 16/10/2013 135

Glossary
136 R5905597 PHXX SERIES 16/10/2013

Index
INDEX
A Remote control 14
Accessories 11 Blanking 36
Adjustments 55–58, 60–64, 66–70, 72–73 Brightness 55
Aspect ratio 58, 60
Detailed setting 60
Auto power off 72 C
Brightness 55 Cleaning 99, 101
Color 55 Filter 99, 101
Color enhancer 56 Cleaning interval 99
Color matrix 57 How to 101
Color temperature 55 Lens 99
Color tone 57 Projector 99
Color variations 66 Vents 99
Computer image 62–63 Cleaning filter 99, 101
Via menu 63 How to clean 101
Contrast 55 Set interval 99
Cornerstone 69 Cleaning interval 99
Curved mode 70 Color 55
Distorted image 68 Color enhancer 56
Fineness 57 Color matrix 57
Image position 64 Color temperature 55
Simple method 64 Color variations 66
Image reverse 72 Compliance 6
Keystone 68 FCC 6
LPF 64 Computer 23
Multi-screen 64 Connection 23
Joints 64 Connection 22–24
Progressive filter 64 Computer 23
Save settings 61 Power 22
Screen size 58 Video equipment 24
Settings 67 Connections 21
Reset 67 Contrast 55
Sharpen 55 Control 91
Super resolution 57 Control panel 91
Test pattern 73 Control panel 91
Tint 55 Control 91
Advanced features 85–88, 90 Control system 80
Control 88, 90 Set 80
Computer 88 Cornerstone 69
Serial terminal 90 Covers 21, 27
Monitoring 90 Installation 27
Password function 85–86 Remove 21
Cancel 86 Curved mode 70
Enable 85
Picture in Picture 87
PIP 87 D
Split 86 Default gateway 79
Supervise 88 DHCP 77
Computer 88 Clear 77
Advanced menu 39–40, 44–47, 49, 51–52, 55 Set 77
Adjustments 55 Dimensions 116
Feature menu 47
Information menu 52
Installation 1 44
Installation 2 45
E
Multi-Screen menu 46 Environmental information 133
Network menu 51 Disposal information 133
Overview 40 Rohs compliance 133
Signal menu 49
Start up 39
Advanced settings 42 F
Image menu 42 Feature menu 47
Aspect ratio 58, 60 Advanced menu 47
Detailed setting 60 Fineness 57
Auto position mode 37
Auto power off 72
G
General considerations 5
B Getting started 29, 32
Batteries 14 Projecting images 32
Installation 14
R5905597 PHXX SERIES 16/10/2013 137

Index
I Network settings 75–80

Image menu 42 Clearing DHCP 77
Advanced menu 42 Control system 80
Image position 64 Set 80
Simple method 64 Default gateway 79
Image reverse 72 How to use 80
Information menu 52 Initialization 80
Advanced menu 52 IP address 78
Installation 14, 20 IP config 79
Batteries 14 Save 79
Remote control 14 IP settings 77
Distorted image 20 Start up 77
Fine streaks 20 Network certification 76
Skewed image 20 Network password settings 76
Installation 1 44 Projector name 75
Advanced menu 44 Setting DHCP 77
Installation 2 45 Subnet mask 78
Advanced menu 45
IP address 78
IP config 79 O
Save 79 Option lens 119, 127
IP settings 77 H LENS 0.8-1.0 119
Start up 77 H LENS 1.3-1.8 127
H LENS 2.2-2.7 127
H LENS 2.8-4.5 119
K H LENS 4.5-8.7 119
Keystone 68 Option lens 0.8-1.0 119–121
Checks 121
Focus correction 120
L Mounting 119
Specifications 121
Lamp 93–94, 96 Option lens 1.3-1.8 127–128
Replacement 93–94, 96 Mounting 127
Interval 93 Specifications 128
Reset parameters 96 Option lens 2.2-2.7 127, 129
Warnings 93 Mounting 127
Lamp parameters 96 Specifications 129
Reset 96 Option lens 2.8-4.5 119, 121, 123
Lamp relay 81, 83 Checks 121
Lamp select, dual 81 Mounting 119
Lamp select, single 83 Specifications 123
Lamp replacement 93–94, 96 Option lens 4.5-8.7 119, 121, 124
Interval 93 Checks 121
Reset parameters 96 Mounting 119
Warnings 93 Specifications 124
Led 106 OSD Lite 30
Lens 121 Navigation 30
Cleaning 121 Results 30
Lens 0.8-1.0 119
Lens 1.3-1.8 127
Lens 2.2-2.7 127
Lens 2.8-4.5 119
P
Lens 4.5-8.7 119 Password function 85–86
Cancel 86
Enable 85
M Picture in Picture 87
PIP 87
Maintenance 99 Position adjust 34
Lens 99 Image 34
Cleaning 99 Power 22
Projector 99 Connection 22
Cleaning 99 Prepare 11
Vents 99 Projector 11
Cleaning 99 Production address 134
Mercury vapor warnings 7 Projected image 34–36
Multi-screen 64 Blanking 36
Joints 64 Distorted 35
Multi-Screen menu 46 Keystone 35
Advanced menu 46 Position adjust 34
Trapezoid 35
Projecting images 33
N Stop 33
Network certification 76 Projector 16
Network menu 51 Configurations 16
Advanced menu 51 Projector cleaning 99
Network password settings 76 Projector distance 17
138 R5905597 PHXX SERIES 16/10/2013

Index
Screen size 17 PHXG-91B 113

Projector name 75 Split 86
Stop projection 33
Subnet mask 78
R Super resolution 57
Remote control 14–15, 29
Batteries 14
Installation 14 T
Indications 29 Terminology 12
Basic 29 Overview 12
Use 15 Test pattern 73
Tint 55
Troubleshooting 103–106
S Image not displayed correctly 104
Safety 5–7 Led 106
Instructions 6 No image appears 103
Mercury vapor warnings 7 Others 105
Ultraviolet radiation 7
UV radiation 7
Screen 17 U
Setup 17 Ultraviolet radiation 7
Screen size 17, 58 Using projector 6
Projector distance 17 Europe 6
Settings 67 UV radiation 7
Reset 67
Setup 17
Ceiling mount holes 17 V
Screen 17 Video equipment 24
Signal menu 49 Connection 24
Advanced menu 49
Specifications 107–111, 113, 115–116
Connectors 116 W
PHWU-81B 109
PHWX-81B 108 Warnings 7
PHXG-91B 107 Mercury vapor warnings 7
RGB signals 110–111, 113, 115 Ultraviolet radiation 7
PHWU-81B 110 UV radiation 7
PHWX-81B 111
R5905597 PHXX SERIES 16/10/2013 139

PHXG-91B, PHWX-81B, Phwu-81b PDF

Uploaded by

Copyright:

Available Formats

PHXG-91B, PHWX-81B, Phwu-81b PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PHXG-91B, PHWX-81B, Phwu-81b PDF

Uploaded by

Copyright:

Available Formats

PHxx series

User and Installation manual

2. Preparing the projector.. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 11

6. Adjustments with the ADVANCED menu. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 55

R5905597 PHXX SERIES 16/10/2013 1

7. Initial network settings .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 75

10. Lamp replacement . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 93

12. Troubleshooting .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 103

13. Specifications . .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 107

A. Option lens H LENS 0.8-1.0, 2.8-4.5 or 4.5-8.7 .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 119

B. Optional lens H LENS 1.3-1.8 .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 127

C. Environmental information .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. .. . 133

2 R5905597 PHXX SERIES 16/10/2013

R5905597 PHXX SERIES 16/10/2013 3

4 R5905597 PHXX SERIES 16/10/2013

About the term PHxx series

1.1 General considerations

CAUTION : TO REDUCE THE RISK OF ELECTRIC

WARNING: Be aware of suspended loads.

R5905597 PHXX SERIES 16/10/2013 5

1.2 Using projector in Europe

1.3 Compliance notice of FCC

1.4 Important safety instructions

6 R5905597 PHXX SERIES 16/10/2013

To prevent personal injury

To prevent fire hazard

R5905597 PHXX SERIES 16/10/2013 7

To prevent the risk of electrical shock

8 R5905597 PHXX SERIES 16/10/2013

To prevent projector damage

R5905597 PHXX SERIES 16/10/2013 9

10 R5905597 PHXX SERIES 16/10/2013

2. PREPARING THE PROJECTOR

2.1 Projector accessories

R5905597 PHXX SERIES 16/10/2013 11

2.2 Terminology overview

1 ON/OFF / POWER key (ON/STANDBY)

Top and side projector

1 Remote control sensor (front)

12 R5905597 PHXX SERIES 16/10/2013

4 Intake vent/Filter cover (inside of the side cover)

Bottom side projector

1 Lock bar (SECURITY ANCHOR)

Terminal panel projector

1 VIDEO IN terminal (BNC)

R5905597 PHXX SERIES 16/10/2013 13

5 HDMI IN terminal (HDMI 19-pin)

2.3 Installation of the batteries into the remote control

Removing the batteries from the remote control

14 R5905597 PHXX SERIES 16/10/2013

2.4 Using the remote control

Reception angle, vertical direction

R5905597 PHXX SERIES 16/10/2013 15

2.5 Projector configurations

Ask a specialist for installation. For details, consult your dealer.

16 R5905597 PHXX SERIES 16/10/2013

2.6 Location of ceiling mounting holes

A : 4 mounting holes for ceiling mount plate. (M4, depth 10 mm)

2.7 Screen setup