A Employbility Skill & Mini Project Report on

OBSTACLE AVOIDING CAR

Submitted By
Utkarsh Bingewar (T150543003)
Shubham Thakur (T150543028 )
Rupesh Rote (T150543022)

A Mini Project Seminar report submitted as a partial fulfillment towards Project

for T.E (E&TC) Engineering, Savitribai Phule Pune University

Guide
Prof. Varsha Nanaware

Department of Electronics & Telecommunication Engineering

G. H. Raisoni Institute of Engineering & Technology,Wagholi, Pune-
412207
 C ER TIFICATE

This is to certify that Utkarsh Bingewar(T150543003), Shubham

Thakur(T150543028) & Rupesh Rote(T150543022) of G.H.Raisoni

Institute of Engineering & Technology,Wagholi,Pune-412207 have

submitted Mini Project report on “OBSTACLE AVODING CAR ” as

a partial fulfillment of T.E(Electronics and Telecommunication) , from

Savitribai Phule Pune University , during the academic year 2017-18.

Prof. Varsha Nanaware Dr.M. R. Bachute

Project Guide H.O.D
Acknowledgment Page
We feel profound pleasure in bringing out this projects report for which
we have to go from pillar to post to make it a reality. This project work reflects
contributions of many people with whom we had long discussions and without
which it would not have been possible. We must first of all, express our heartiest
gratitude to respected Prof. Prof.Dr.M. R. Bachute (Dept. of E&TC) for
providing us all guidance to complete project.
It would be unfair if we do not mention the invaluable contribution and timely
co-operation extended to us by staff member of our department. And especially
we can never forget the most worthy advices given by Varsha Nanaware
( Dept of E&TC), that would help us the entire lifetime.
Last but not the least we express our sincere thanks to the institute G.H.R.I.E.T.,
Wagholi, Pune for providing such a platform for implementing the ideas in our
mind
Abstract
Obstacle avoidance is one of the most important aspects of mobile
robotics. Without it, robot movement would be very restrictive and fragile. This
project proposes robotic vehicle that has an intelligence built in it such that it
directs itself whenever an obstacle comes in its path. So, to protect the robot
from any physical damages. This can be design to build an obstacle avoidance
robotic vehicle using ultrasonic sensors for its movement. A micro-controller
(AT mega 328P) is used to achieve the desired operation. An ultrasonic sensor is
used to detect any obstacle ahead of it and sends a command to the micro-
controller. Depending on the input signal received, the micro-controller
redirects the robot to move in an alternate direction by actuating the motors
which are interfaced to it through a motor driver.
CHAPTER NO: 1
INTRODUCTION
 INTRODUCTION

Robotics is part of Todays communication. In today’s world ROBOTICS is fast

growing and interesting field. It is simplest way for latest technology modification. Now a
days communication is part of advancement of technology, so we decided to work on
ROBOTICS field, and design something which will make human life simpler in day today
aspect. Thus we are supporting this cause.

An obstacle avoiding robot is an intelligent device, which can automatically sense

and overcome obstacles on its path. Obstacle Avoidance is a robotic discipline with the
objective of moving vehicles on the basis of the sensorial information. The use of these
methods front to classic methods (path planning) is a natural alternative when the scenario is
dynamic with an unpredictable behaviour. In these cases, the surroundings do not remain
invariable, and thus the sensory information is used to detect the changes consequently
adapting moving. It will automatically scan the surrounding for further path.

This project is basic stage of any automatic robot.This ROBOT has sufficient
intelligence to cover the maximum area of provided space. It has a ultrasonic sensor which
are used to sense the obstacles coming in between the path of ROBOT. It will move in a
particular direction and avoid the obstacle which is coming in its path. We have used two D.C
motors to give motion to the ROBOT. The construction of the ROBOT circuit is easy and
small .The electronics parts used in the ROBOT circuits are easily available and cheap too.
CHAPTER NO :2
LITERATURE SURVEY
LITERATURE SURVEY:

We reviewed different obstacle detecting robot mechanisms that have been built
by a lot of students and other practitioners that are in exisitance. For an
autonomous mobile robot performing a navigation-based task in a vague
environment, to detect and to avoid encountered obstacles is an important issue and
a key function for the robot body safety as well as for the task continuity. Obstacle
detection and avoidance in a real world environment that appears so easy to
humans is a rather difficult task for autonomous mobile robots and is still a well-
researched topic in robotics.In many previous works, a wide range of sensors and
various methods for detecting and avoiding obstacles for mobile robot purpose
have been proposed. Good references related to the developed sensor systems and
proposed detection and avoidance algorithms can be found. Based on these
developed sensor systems, various approaches related to this work can be grouped
CHAPTER NO: 3
DESIGN & HARDWARE
REQUIREMENTS
Design:

Hardware:

 Arduino uno
 Ultrasonic sensor
 Motor (100 RPM)
 Motor driver IC (L293D)
 Battery (9V)
 Breadboard
CHAPTER NO:4
BLOCK DIAGRAM
BLOCK DIAGRAM

The basic block diagram of the obstacle avoiding car is shown in above figure. Mainly this
block diagram consists of the following essential blocks.

1. Arduino uno
2. Ultrasonic sensor
3. Motor driver(L293D)

1) Arduino uno -

Arduino Uno is an ATmega 328p Microcontroller based prototyping board. It is an open

source electronic prototyping platform that can be used with various sensors and
actuators.It is used for controlling all the operation and assign task to each device.

2) Ultrasonic sensor -

It is an Ultrasonic Range Finder Sensor. It is a non-contact based distance measurement

system and can measure distance of 2cm to 4m.Ultrasonic sensor is mainly use to detect
the obstacle

3) Motor driver -

It is a motor driver which can provide bi-directional drive current for two motors.
CHAPTER NO:5
WORKING
Working Principle:

The obstacle avoidance robotic vehicle uses ultrasonic sensors for its movements. Arduino is
used to achieve the desired operation. The motors are connected through motor driver IC to
Arduino. The ultrasonic sensor is attached in front of the robot.

Whenever the robot is going on the desired path the ultrasonic sensor transmits the ultrasonic
waves continuously from its sensor head. Whenever an obstacle comes ahead of it the
ultrasonic waves are reflected back from an object and that information is passed to the
arduino. The arduino controls the motors left, right, back, front, based on ultrasonic signals.
In order to control the speed of each motor pulse width modulation is used (PWM).

When ultrasonic sensor detect the object which is kept inside the path it will send the signal
toward the arduino uno and according to that it will it will rotate the motor M3 & M4 in
forward direction and rotate the motor M1 & M2 in reverse direction such way that the car
get moving in left direction .

Similarly in every time when ever an obstacle in found to be in path of car it will detect it and
rotate the car in left direction to avoid the obstacle.
ARDUINO UNO:

Arduino/Genuino Uno is a microcontroller board based on the ATmega328P. It has 14 digital

input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz
quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. It contains
everything needed to support the microcontroller; simply connect it to a computer with a
USB cable or power it with a AC-to-DC adapter or battery to get started.. You can tinker with
your UNO without worring too much about doing something wrong, worst case scenario you
can replace the chip for a few dollars and start over again. "Uno" means one in Italian and
was chosen to mark the release of Arduino Software (IDE) 1.0. The Uno board and version
1.0 of Arduino Software (IDE) were the reference versions of Arduino, now evolved to newer
releases. The Uno board is the first in a series of USB Arduino boards, and the reference
model for the Arduino platform; for an extensive list of current, past or outdated boards see
the Arduino index of boards.
Motor Drivers (L293D IC)

 Motor drivers take a low current control signal but provide a higher current signal,
thus acting as a current amplifier. The higher current signal drives the motors. L293D
is a motor driver that allows direct current (DC) motor to drive on either direction. It
contains two inbuilt H-bridge driver circuits . To rotate the motor in clockwise or
anticlockwise direction, voltage need to change its direction. H-bridge is a circuit that
allows voltage to be flown in either direction. Hence H-bridge IC are ideal for driving
a DC motor .
 Here are 4 input pins for L293d, pin 2,7 on the left and pin 15 ,10 on the right as
shown on the pin diagram. Left input pins will regulate the rotation of motor
connected across left side and right input for motor on the right hand side. The motors
are rotated on the basis of the inputs provided across the input pins as LOGIC 0 or
LOGIC 1. For rotating the motor in clockwise direction the input pins has to be
provided with Logic 1 and Logic 0.Enable pins 1 and 9 (corresponding to the two
motors) must be high for motors to start operating. When an enable input is high, the
associated driver gets enabled. As a result, the outputs become active and work in
phase with their inputs. Similarly, when the enable input is low, that driver is disabled,
and their outputs are off and in the high-impedance state.
Motor (100rpm/ 12V DC Motor)

 The obstacle detection and avoiding robot uses two 200rpm and 12V DC geared
motors. The motor used has a 6mm shaft diameter with internal holes. The internal
holes are for easy mounting of the wheels by using screws. It is an easy to use low-
cost motor for robotics application

 An Electric DC motor is a machine which converts electric energy into mechanical

energy. The working of DC motor is based on the principle that when a current-
carrying conductor is placed in a magnetic field, it experiences a mechanical force.

The direction of mechanical force is given by Fleming’s Left-hand Rule and its
magnitude is given by F = BIL Newton.

 DC motors are seldom used in ordinary applications because all electric supply
companies furnish alternating current.
ULTRASONIC SENSOR

 An Ultrasonic sensor is a device that can measure the distance to an object by using
sound waves. It measures distance by sending out a sound wave at a specific
frequency and listening for that sound wave to bounce back. By recording the elapsed
time between the sound wave being generated and the sound wave bouncing back, it
is possible to calculate the distance between the sonar sensor and the object.

 It emits an ultrasound at 40 000 Hz which travels through the air and if there is an
object or obstacle on its path It will bounce back to the module. Considering the travel
time and the speed of the sound you can calculate the distance.

 The HC-SR04 Ultrasonic Module has 4 pins, Ground, VCC, Trig and Echo. The
Ground and the VCC pins of the module needs to be connected to the Ground and the
5 volts pins on the Arduino Board respectively and the trig and echo pins to any
Digital I/O pin on the Arduino Board.

 In order to generate the ultrasound you need to set the Trig on a High State for 10 µs.
That will send out an 8 cycle sonic burst which will travel at the speed sound and it
will be received in the Echo pin. The Echo pin will output the time in microseconds
the sound wave traveled.
CHAPTER NO:6
CIRCUIT DIAGRAM
CIRCUIT DIAGRAM
CHAPTER NO:7
APPLICATIONS
 APPLICATIONS

This device has application in surveying different landscapes and mapping them.It can also
be used in commercial devices like
 Automated lawn mover
 Smart room cleaner etc
 Obstacle avoiding robots can be used in almost all mobile robot navigation systems.
 They can also be used in dangerous environments, where human penetration could be
fatal.
 Unmanned vehicle driving
 Mining Vehicle that uses Obstacle Detection
 CHAPTER NO:8
EXPERIMENTAL RESULTS
EXPERIMENTAL RESULT
CHAPTER NO: 9
CONCLUSION
 CONCLUSION

The goal of our project is to create a autonomous robot which intelligently detects the
obstacle in his path and navigate according to the actions we set for it.
CHAPTER NO: 10
REFERENCES
 REFERENCES

BOOKS:
 D. Floreano and J. Urzelai. “Evolutionary Robots with Online Self-Organization and
Behavioral Fitness”
 Oussama Khatib. “Real-Time Obstacle Avoidance for Manipulators and Mobile
Robots”,
 Marija Seder. “Hierarchical Path Planning of Mobile robots in Complex Indoor
Environments”

WEBSITES:
 http://www.datasheetcatalog.com
 http://www.instructabal.com
 http://en.wikipedia.org/wiki/Artificial_intelligence
 http://science.howstuffworks.com/robot2.htm
 http://arduino.cc/en/Main/arduinoBoardUno

Magazines:

 Electronics for you

 Electronic Hub
CHAPTER NO: 11
COSTING
 List of Components and Expenses

Component Rating Quantity Cost

Name
Arduino uno ATmega328P 1 460
Ultrasonic 150
Module 1

Motor 100 RPM 4 700

Motor 1 90
Drivers
(L293D IC)
Breadboard 1 100
Tyres 4 100
Battery 9V 2 40
TOTAL 1,640 Rs
COST
CHAPTER NO: 12
PROGRAM
// OBSTACLE AVOIDING CAR:

const int trigPin = 10;

const int echoPin = 11;
const int in1 = 9;
const int in2 = 8;
const int in3 = 4;
const int in4 = 3;

void setup()
{
pinMode(trigPin, OUTPUT);
pinMode(echoPin, INPUT);
pinMode (in1, OUTPUT);
pinMode (in2, OUTPUT);
pinMode (in3, OUTPUT);
pinMode (in4, OUTPUT);
}
long duration;
int distance;

void loop()
{
digitalWrite(trigPin, LOW);
delayMicroseconds(2);
digitalWrite(trigPin, HIGH);
delayMicroseconds(10);
digitalWrite(trigPin, LOW);
duration = pulseIn(echoPin, HIGH);
distance = duration*0.034/2;
if(distance<30)
{
digitalWrite(in1, HIGH);
digitalWrite(in2, LOW);
digitalWrite(in3, LOW);
digitalWrite(in4, HIGH);
delay(600);
}

else
{
digitalWrite(in1, HIGH);
digitalWrite(in2, LOW);
digitalWrite(in3, HIGH);
digitalWrite(in4, LOW);
}
delay(0);
}