Quick Installation Guide: Port Definition

PA2
Quick Installation Guide
PA2
Port Definition
① ③ ⑤ ⑥ ⑧
② ④ ⑦
⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮
1 Speakerinterface: according to the device input voltage adaptive output maximum
power; 4Ω speaker, POE / 10W, 12V / 10W,18V / 20W, 24V / 30W. The greater the
horn impedance, the smaller the output power.
Suggested wire diameter: 18AWG or larger diameter.
2 Headset interface: speaker audio signal output impedance 32 Ohm,single-ended
output voltage 1.2 V, for external headset or active speakers.
3 LED interface: output 5V, 5 mA current , can be an external LED, indicating the
network status, call status, registration status.
4 Function key interface: connection switch, you can log on page set the call number
or IP address.
5 Microphone interface: the proposed use of impedance of 2.2K Ohm electret
condenser microphone, sensitivity: -38dB, bias voltage 2.2V. Microphone signal
cable it is recommended to use a shielded cable and do not connect the shield
cable to the grounding screw, improve anti-interference.
6 Switch input interface: the connection switch, you need to log on to the relevant
settings page.
7 Switch output interface: Corresponding to the short-circuit input interface, login
device security page settings, you can control the alarm light, electric locks and other
equipment; with the adjacent ⑧ power port connection for external equipment
power supply.
8 Power input interface: 12V ~ 24V 2A input, according to the input voltage to
determine the maximum output power amplifier.
9 Camera interface: standard RJ45 interface, connect the original camera, the
proposed use of five or five sub-network cable
10 Ethernet interface: WAN port, standard RJ45 interface, 10 / 100M adaptive, support
POE input, it is recommended to use five or Super five network cable.
11 Registration/Network LED: indicates network status, call status, registration status.
Fast flashing: network anomaly or SIP account exception. Slow flashing: during a call.
Always bright: successful registration.
12 Volume control key: standby to adjust the volume of the ringtone, call only adjust
the call volume, broadcast only adjust the broadcast volume..Long press the volume
down key to broadcast the IP address.Long press the volume plus key to switch the
IP address acquisition mode (Specific operation see below search door phone).
13 Restore factory key: press and hold for 3 seconds to flash the device to restart and
restore the factory settings.
14 Recording output interface: the local microphone voice and call voice mixed output,
suitable for computer and other equipment recording.
15 Grounding screw: external parts Metal housing needs to be connected to this
interface to prevent static electricity and other interference caused the equipment
to work abnormally.(except for microphone accessories)
()
1. Installation
The first step: the equipment with metal strips (user-owned) fixed in the installation
location.
The second step: the Function Key button, speakers and other metal shell with
thick wires connected to the device ⑮ grounding screw. And then connect the line of
the terminal in turn
inserted into the corresponding interface.
The third step: plug the network cable and power, the device light flashes on behalf of
the power connection is normal.
2. Searching Door Phone

There are three methods as shown below to search the door phone.
Method 1:
Open the iDoorPhone Network Scanner. Press the Refresh button to search the
door phone and find the IP address.
(Download address http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe )
Method 2:
Connect the speaker, by pressing the volume down key for 3 seconds (after 30 seconds
after power on), the device automatically voice broadcast the machine's IP address.
Method 3:
Long press the volume plus key for 10 seconds, the speaker issued a rapid beep, and
then quickly press the three volume plus the key, beep stopped. Wait 10 seconds,
Successfully switch to dynamic IP after the system automatically voice broadcast IP
address. Switching again will become a fixed IP address.
Default Setting
Default DHCP Static IP
Disable 192.168.1.128
Client Address
Voice broadcast Hold the volume down Default Web
80
IP address key for 3 seconds Port
3. SIP door phone setting
Step 1: Log in to the device page
Use the web browser input IP (for example: http: //192.168.1.128) access, the default
user admin,
password admin.
Step 2: Add the SIP account.

Set SIP server address, port, user name, password and SIP user with assigned SIP
account parameters.
Select “Activate”, and then click [Apply] to save this setting.
Step 3: Set the volume (if not connected can skip)
Set the device volume size, as shown below, click [Apply].
Hands-free volume setting: normal call speaker volume size.
Broadcast output volume: server music broadcast speaker volume size.
Signal volume: call ringing, power back to ling, correct tone, error tone and other
volume size.
Microphone Input Volume: microphone volume size.
Step 4: Setting Function Key

Set the Function Key as shown below for a quick start. Click [Apply] to save this
setting.
Type: Hot Key
Number 1: the Function Key will dial to this Number 1.
Number 2: if Number 1 is unavailable, it will be forwarded to Number 2.
Line: working line
Subtype: speed dial
Step 5: Setting Speaker Settings mode
The Speaker Settings default mode is <panel speaker>. <panel speaker> is the
installation of speakers and microphones in a common shell. In order to ensure the
speaker's voice quality and avoid damaging the horn, the output power is limited to 10W
If external loud speaker user for broadcasting, It can be adjusted to the <external
speaker> mode
At this time, we can choose 10W / 20W / 30W audio output power, we need to
match the corresponding power supply, for example:
Input Power Audio output Speaker Type
POE 10W 10W/4Ω
12V/2A DC 10W 10W/4Ω
18V/2A DC 20W 20W/4Ω
24V/2A DC 30W 30W/4Ω

PA2
Quick Installation Guide
Step 6: Set the camera (if not connected can skip)

The original camera does not need to set up, connected to the device ⑨ black RJ45
network port and restart the device to wait 1 minute, the camera automatically
connected successfully. To connect a non-original camera, insert the camera into
another LAN or LAN port. Configure the following parameters and click [Apply].
Connection mode: select external, click [Apply], restart the device.

User name: external camera login required account.
Password: external camera login password required.
Camera type: select the camera manufacturers.
IP address: IP address of the camera, please use the camera matching scan tool to
obtain the IP address.
Port: camera port number.
RTSP information: click [Apply], the connection automatically shows the camera does
not show the reverse.
Preview: copy and paste the main stream or sub-stream Url into the VLC player, or click
[Preview] to display the current camera video.
Information on this document is subject to change without notice.

Fanvil makes no warranties with respect to this document, due to
misuseThis document is caused by indirect or incidental damages,
Fanvil does not assume any responsibility.
For more product information, please visit www.fanvil.com

Quick Installation Guide: Port Definition

Uploaded by

Copyright:

Available Formats

Quick Installation Guide: Port Definition

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Quick Installation Guide: Port Definition

Uploaded by

Copyright:

Available Formats

PA2

Quick Installation Guide

2. Searching Door Phone

Step 2: Add the SIP account.

Step 4: Setting Function Key

Input Power Audio output Speaker Type

POE 10W 10W/4Ω

12V/2A DC 10W 10W/4Ω

18V/2A DC 20W 20W/4Ω

24V/2A DC 30W 30W/4Ω

Step 6: Set the camera (if not connected can skip)

Connection mode: select external, click [Apply], restart the device.

Information on this document is subject to change without notice.

You might also like