0% found this document useful (0 votes)
69 views6 pages

USB Extension Control Chip CH315G USB Signal Isolation Control Chip CH315H

This document provides information on the CH315G and CH315H USB extension and isolation control chips: - The CH315G is used for USB signal extension over long distances up to 75m for full-speed and 300m for low-speed, while the CH315H provides optical or magnetic isolation of USB signals. - Both chips support full-speed and low-speed USB transfer and allow for dynamic insertion and removal of USB devices. - Key features include supporting various USB transfer types, automatic speed detection, upstream/downstream configuration, signal extension/isolation circuits, and simple peripheral circuitry requiring no external clock.

Uploaded by

Arthit Somrang
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
69 views6 pages

USB Extension Control Chip CH315G USB Signal Isolation Control Chip CH315H

This document provides information on the CH315G and CH315H USB extension and isolation control chips: - The CH315G is used for USB signal extension over long distances up to 75m for full-speed and 300m for low-speed, while the CH315H provides optical or magnetic isolation of USB signals. - Both chips support full-speed and low-speed USB transfer and allow for dynamic insertion and removal of USB devices. - Key features include supporting various USB transfer types, automatic speed detection, upstream/downstream configuration, signal extension/isolation circuits, and simple peripheral circuitry requiring no external clock.

Uploaded by

Arthit Somrang
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

The DataSheet of CH315 (the first) 1

USB extension control chip CH315G


USB signal isolation control chip CH315H
DataSheet
Version:1A
http://wch.cn
http://wch-ic.com

1. Introduction
CH315G is USB extension control chip, used for USB signal real time transmit and extend transfer
distance.
CH315H is USB signals isolation control chip, used for USB bus optical isolator or magnetic isolator.
CH315 supports full-speed and low-speed transfer, support USB device dynamic insert and remove.
The following is application image.

USB keyboard
Power Power Power USB mice
CH315G CH315G USB Flash
PC Drive /Flash
Or other Upstream Downstream disk
USB Long distance USB printer
Host USB UP#=GND Signal transfer UP#=VCC USB USB collection
Full-speed 75m box
Low-speed 300m USB controller

USB keyboard
Photic coupler USB mice
Power CH315H isolator CH315H Power USB Flash
PC Drive /Flash
Or other Upstream Downstream disk
USB Magnetic USB printer
Host UP#=GND coupler UP#=VCC USB collection
isolator box
USB USB
USB controller

2. Features
● supports 12Mbps full-speed and 1.5Mbps low-speed USB transfer, compatible with USB 2.0.
● supports USB control transfer, bulk transfer, interrupt transfer, synchronous/isochronous transfer.
The DataSheet of CH315 (the first) 2

● automatically detect USB Full-Speed or USB Low-Speed, CH315H offer USB transfer status indication.
● the same chip can be configured as upstream mode and downstream mode, connect to USB-Host and
USB-Device.
● the downstream mode can automatically detect USB device connection and removal, the upstream mode
can automatically simulate USB device connection and removal.
● set impedance matching serial resistor of USB signal, pull-up resistor of USB device port, pull-down
resistor of USB host port.
● set PLL and 12MHz USB clock internal, no need crystal or crystal resonator, the peripheral circuit is
simply.
● set USB signal extension circuit in the CH315G, support category 5 or category 5 unshielded twisted-pair
super, the transfer distance is no less than 75m of 12Mbps full-speed USB signal, the transfer distance is no
less than 300m of 1.5Mbps.
● set current driven circuit of photic coupler in CH315H, support the low-cost 6N137, the photic coupler can
not influenced by electromagnetism.
● only hardware project, real time of USB protocol, no need other drive program, support Windows
98/ME/2000/XP/Vista/Server200X/64bit-Vista and Linux.
● set 3.3V power manostat in the internal. Support 5V power (default) and 3.3V power.
● CH315G adopt SOP-14 lead-free package, CH315H adopt SOP-18 lead-free package, compatible with
RoHS.

3. Package

Package shape Width of plastic Pitch of pin Instruction of package Ordering type
SOP-14 3.9mm 150mil 1.27mm 50mil Small outline package of 14-pin CH315G
SOP-18 7.62mm 300mil 1.27mm 50mil Small outline package of 18-pin CH315H

4. Pins
CH315G CH315H Pin
Pin Type Pin Description
Pin No. Pin No. Name
Positive power input port, requires an external 0.1uF
3,9 13,16 VCC POWER
power decoupling capacitance
2,6 8,17,18 GND POWER Public ground, ground connection for USB
Attachment of VCC input external power while
14 3 V3 POWER 3.3V;connects of 0.01uF decoupling capacitance outside
while 5V
13 1 UD+ USB signal Directly connect to USB bus D+ data bus
The DataSheet of CH315 (the first) 3

12 2 UD- USB signal Directly connect to USB bus D- data bus


Consult Consult power of internal simulate circuit, require an
1 No REF
power resistor and decoupling capacitance
Simulate
5 No XD+ Directly connect to difference extension wire positive port
signal
Simulate Directly connect to difference extension wire negative
4 No XD-
signal port
Separate transfer P signal input, connect with photic
No 14 OPIP IN
coupler or magnetism coupler P logic output port
Separate transfer N signal input, connect with photic
No 15 OPIN IN
coupler or magnetism coupler N logic output port
Separate transfer P signal output, connect with photic
No 6 OPOP OUT
coupler or magnetism coupler P control input port
Separate transfer N signal output, connect with photic
No 7 OPON OUT
coupler or magnetism coupler N control input port
USB transfer speed automatically check the result ouput.
No 5 LSO# OUT Low-level is USB low-speed 1.5Mbps, high-level is USB
full-speed 12Mbps
USB transfer speed select input,
No 4 LSI# IN Low-level is USB-low speed 1.5Mbps, high-level is USB
full-speed 12Mbps.
Mode select input, with pull-up resistor,
10 12 UP# IN Low-level is upstream mode, high-level is downstream
mode
Drain open USB transfer status output, active with low-level, with
No 11 ACT#
OUT pull-up resistor
7,8,9 9,10 NC. Un-connect Forbid to connect

5. Function
CH315 can direct use USB power. When using 5V power, V3 pin must connect with about 0.01uF
decoupling capacitance. When using 3.3V power, V3 must connect with VCC, and input the outside 3.3V
power.
CH315G using category 5 or category 5 unshielded twisted-pair super (net wire) or USB signal wire
and similar difference signal twisted-pair. If the characteristic impedance is not matching, need to parallel
connect resistor to ground of output port XD+/XD-.
The transfer distance of CH315G is relative with transfer wire quality. When using common net wire,
the transfer distance is no less than 300m of low-speed USB signal, the transfer distance is no less than 75m
of full-speed USB signal. The current resistor of common net wire is less than 10Ω/100m. If the current
resistor is too big, it will influence on transfer distance, and influence on USB supply power, upgrade ground
power of device port.
The transfer distance of CH315G has relative with USB host time characteristics of computer chip
groups. For full-speed USB signal, the trip acknowledge time of electron in transfer wire does not pass
computer waiting time (several ns), so the transfer distance is limited.
The ACT# is USB transfer current status output of CH315H, connect with LED to indicate USB
The DataSheet of CH315 (the first) 4

transfer.
CH315H support the common type 6N137 single channel high-speed photic coupler (need four) or the
type is HCPL-2630,2631,0630,0631 double channels (only need two). The isolate power is determined by
photic coupler, the typical isolate power is 5000V of 6N137. CH315H also support magnetism coupler,
recommended to use photic coupler, not influenced by the electromagnetism. In order to support 12Mbps
USB full-speed signal, the transfer speed is more than 10Mbps of photic coupler or magnetism coupler.
CH315 is hardware project of USB signal extension and USB signal electric isolation, compatible with
the relative criterion, completely transparent to the USB protocol. For the CH315, no need any drive, but the
USB device may need to install driver, the method is the same with the no isolation. The common USB
Flash Drive, keyboard, mice and other USB device may no need driver.
CH315 can automatically detect USB full-speed and USB low-speed, support plug and play,
automatically detect and simulate the USB device connect and disconnect. CH315G can be used to produce
active USB extension cable, extension USB transmission distance, signal acquisition and on-line remote
control; CH315G can be used to produce optical isolator USB signals and reduce signal interference,
improve signal acquisition accuracy.

6. Parameter
6.1. Absolute maximum rating (Stresses above those listed can cause permanent damage to the device.
Exposure to maximum rated conditions can affect device operation and reliability.)
Name Parameter note Min. Max. Units
TA Ambient operating temperature -40 85 ℃
TS Storage temperature -55 125 ℃
VCC Voltage source (VCC connects to power, GND to ground) -0.5 6.0 V
VIO The voltage of input or output pin -0.5 VCC+0.5 V

6.2. Electrical parameter (test conditions: TA=25℃, VCC=5V, excluding pin connection of USB bus)
Unit
Name Note of parameter Min. Typ. Max.
s
VCC Power voltage 3.2 5 5.3 V
ICCs Static source current 2 5 mA
ICCa Source current when working 20 50 mA
VIL Input Voltage LOW OPIN/N -0.5 0.8 V
VIH Input Voltage HIGH OPIP/N 2.0 VCC+0.5 V
VOL Output Voltage LOW (draw 8mA current) OPOP/N 0.5 V
VOH Output Voltage HIGH (output 8mA current) OPOP/N VCC-0.5 V
IUPup Input current in UP# pin with internal pull-up resistor 3 150 300 uA
IUPact Input current in ACT# pin with internal pull-up resistor 100 230 400 uA
Lfs Extension distance of full-speed USB signal 75 m
Lls Extension distance of low-speed USB signal 300 m

7. Application
7.1. Active USB extension cable (following image)
The following USB extension cable is composed by two groups CH315G circuit.
The DataSheet of CH315 (the first) 5

The upstream contains U3, P3 etc. the up port P3 is used to connect to computer or other USB-Host, U3
etc upstream circuit share power with computer or USB host through P3, at least public ground.
The downstream contains U4, P4 etc, the down port P4 is used to connect to USB-Device, such as USB
keyboard, USB mice, USB Flash Drive, USB data acquisition box, USB controller etc. USB device, U4 etc.
downstream circuit share power with USB device, at least public ground.
There is one group electrical wire between upstream U3 and downstream U4, using common network
cable (category 5 or category 5 unshielded twisted-pair super) connection. The cable included XD+ and XD-
two differential signaling lines and at least one public ground. If there are remaining signal lines, it can also
be used an additional ground wire and power wire.
For the normal eight core cable, please consult to the figure RJ45: two differential signal lines, four
ground wires, two power wires. The power wire can offer +5V source to USB device port, but impact by the
network cable DC resistance of the voltage drop, especially when the USB device draws more current, the
USB device port of the actual supply voltage is usually less than 5V, and even individual USB device may be
unable to work, then need to provide independent power for the downstream.
The capacitance of C11, C12, C14, C15 is from 4700pF to 0.02uF, used to decoupling of internal power.
C13 and C16 is 0.1uF, used to decoupling of power of CH315. C17 is decoupling of the USB device on P4
port. R11 and R12 are used to adjust the internal consult power.
USB port contains P3 and P4, USB bus contain one pair of 5V power wire and one pair of data signal.
Usually, +5V power wire is red, the ground wire is black, D+ signal wire is green, D- signal wire is white.
When designing the PCB, pay much attention to some notes: C11, C12, C13, C14, C15 and C16
connected to the pin as close as possible CH315G, makes sure D+ and D- are parallel, XD+ and XD- are
parallel, and supply ground net or pour copper beside them to decrease the disturbance from outside signal.

7.2. USB signal isolator (following image)


The following USB isolator is composed by two groups CH315H circuit.
LSI# pin directly connect to LSO# pin in CH315H, automatically detect USB speed. In actual, if need
to support certain speed, such as, support low-speed USB keyboard, make LSI# as low-level.
The DataSheet of CH315 (the first) 6

The upstream contains U1, P1 etc. the up port P1 is used to connect to computer or other USB-Host, U1
etc upstream circuit share power with computer or USB host through P1, at least public ground.
The downstream contains U2, P2 etc, the down port P2 is used to connect to USB-Device, such as USB
keyboard, USB mice, USB Flash Drive, USB data acquisition box, USB controller etc. USB device, U2 etc.
downstream circuit share power with USB device, at least public ground.
There is one group signal isolator circuit between upstream U1 and downstream U2, select magnetic or
optical isolation. The image id optical isolation, the signal isolation is composed by O1+O2 and O3+O4 two
pairs of photic coupler and associated resistance R1~R8, capacitor C7~C10. The type of photic coupler can
select single channel 6N137 or double channels HCPL2631 etc. high-speed photic coupler may require
decoupling capacitors between power pin and ground pin, the figure is not drawn). Used in 12Mbps
full-speed USB signal, need to consider the speed and the speed symmetry, influence on signal slow-moving
and balance, recommended to select the transmission rate is greater than 10Mbit, and adjust the R1/C7,
R2/C8, R5/C9, R6/C10, to optimize the output signal between rising edge and falling edge.
L1 indicates the USB data transfer in progress. The capacitance of C1 and C4 is from 4700pF to 0.02uF,
for Ch315H decoupling the internal power node, C2 and C5 has a capacity of 0.1uF, for Ch315H chip power
supply decoupling.
When designing the PCB, pay much attention to some notes: decoupling capacitors C1, C2, C4 and C5
connect to the pin as close as possible CH315H, makes sure D+ and D- are parallel, and supply ground net or
pour copper beside them to decrease the disturbance from outside signal.

You might also like