SMT inductors

SIMID series, SIMID 1210-100

Series/Type: B82422A*100
Date: October 2012

a~í~=pÜÉÉí

¤EPCOS AG 2012. Reproduction, publication and dissemination of this publication, enclosures

hereto and the information contained therein without EPCOS’ prior express consent is prohibited.
 SMT inductors, SIMID series B82422A*100
SIMID 1210-100

Size 1210 (EIA) or 3225 (IEC)

Rated inductance 0.0082 ... 100 μH
Rated current 65 ... 800 mA

Construction
■ Ceramic or ferrite core
■ Laser-welded winding
■ Flame-retardant molding

Features
■ Temperature range up to +145 °C
■ High Q factor
■ High resonance frequency
■ Qualified to AEC-Q200
■ Suitable for lead-free reflow soldering
as referenced in JEDEC J-STD 020D
■ RoHS-compatible

Applications
■ Filtering of supply voltages, coupling, decoupling
■ Antenna systems
■ Automotive electronics
■ Telecommunications
■ Consumer and data processing equipment
■ Industrial electronics

Terminals
■ Base material CuSn6
■ Layer composition Cu, Ag, Sn (lead-free)1)
■ Electro-plated

Marking
■ Marking on component:
Manufacturer, L value (in nH),
tolerance of L value (coded), date of manufacture (YWWD)
■ Minimum data on reel:
Manufacturer, ordering code, L value,
quantity, date of packing

Delivery mode and packing units

■ 8-mm blister tape, wound on 180-mm or 330-mm ‡ reel
■ Packing units:
180-mm reel: 2000 pcs./reel
330-mm reel: 8000 pcs./reel

1) Ni-barrier-plated terminals on request (B82422A*150).

Please read Cautions and warnings and

Important notes at the end of this document. 2 10/12
 SMT inductors, SIMID series B82422A*100
SIMID 1210-100

Dimensional drawing and layout recommendation

0.5±0.2 1)

A
2±0.11)

B C B
D
IND0053-6
3.2+0.3 0.4 min.1)
2±0.1

A B C D
2.7 1.15 2.1 4.4
0.15 max. 2.5+0.3

Marking

1) Soldering area IND0073-6-E Dimensions in mm

Taping and packing

Blister tape Reel

4±0.1 14.4 max. 12.75 +0.15

_0
1.75±0.1

Component 1.5+0.1 2±0.05

3.5±0.05

180 +0
330 +0
_2
_2
8±0.3
<_ 4.2

<_ 2.6 4±0.1 1.0+0.2 8.4 +1.5

_0 62±1.5
IND0592-V
Direction of unreeling
IND0559-Z-E

Dimensions in mm

Please read Cautions and warnings and

Important notes at the end of this document. 3 10/12
 SMT inductors, SIMID series B82422A*100
SIMID 1210-100

Technical data and measuring conditions

Rated inductance LR Measured with impedance analyzer Agilent 4294A

at frequency fL, 0.1 V, +20 °C
Q factor Qmin Measured with impedance analyzer Agilent 4294A
at frequency fQ, +20 °C
Rated temperature TR +125 qC
Rated current IR Maximum permissible DC with inductance decrease
'L/L0 d 10% and temperature increase
of d 20 K at rated temperature
Self-resonance frequency fres,min Measured with impedance analyzer Agilent E4991A /
network analyzer Agilent E8362B, +20 °C
DC resistance Rmax Measured at +20 qC
Solderability (lead-free) Sn95.5Ag3.8Cu0.7: +(245 r5) °C, (5 r0.3) s
Wetting of soldering area t 90%
(based on IEC 60068-2-58)
Resistance to soldering heat +260 qC, 40 s (as referenced in JEDEC J-STD 020D)
Climatic category 55/125/56 (to IEC 60068-1)
Storage conditions Mounted: –55 °C … +125 °C
Packaged: –25 °C … +40 °C, d 75% RH
Weight Approx. 50 mg

Please read Cautions and warnings and

Important notes at the end of this document. 4 10/12
 SMT inductors, SIMID series B82422A*100
SIMID 1210-100

Characteristics and ordering codes

LR Tolerance fL Qmin fQ IR Rmax fres, min Ordering code 1)2)

PH MHz MHz mA : MHz (‡ 180-mm reel)

Core material: ceramic

0.0082 r5% ^ J 10 20 100 800 0.08 4000 B82422A3829+100
0.010 r10% ^ K 10 20 100 750 0.09 4000 B82422A3100+100
0.012 10 25 100 700 0.10 3500 B82422A3120+100
0.015 10 27 100 640 0.12 3000 B82422A3150+100
0.018 10 30 100 640 0.12 2500 B82422A3180+100
0.022 10 30 100 600 0.14 2500 B82422A3220+100
0.027 10 23 50 600 0.14 1850 B82422A3270+100
0.033 10 20 50 540 0.17 1700 B82422A3330+100
0.039 10 25 50 530 0.18 1450 B82422A3390+100
0.047 10 26 50 510 0.19 1350 B82422A3470+100
0.056 10 26 50 500 0.20 1200 B82422A3560+100
0.068 10 27 50 480 0.21 1150 B82422A3680+100
0.082 10 27 50 450 0.24 1050 B82422A3820+100
0.10 10 25 50 440 0.26 1000 B82422A3101+100
0.12 1 22 30 400 0.32 880 B82422A3121+100
0.15 1 25 30 390 0.33 850 B82422A3151+100
0.18 1 25 30 360 0.38 800 B82422A3181+100
0.22 1 25 30 280 0.64 700 B82422A3221+100
0.27 1 20 30 235 0.90 650 B82422A3271+100
0.33 1 22 30 200 1.3 580 B82422A3331+100
0.39 1 22 30 190 1.4 540 B82422A3391+100
0.47 1 22 30 150 2.2 480 B82422A3471+100
0.56 1 22 30 150 2.2 400 B82422A3561+100
0.68 1 22 30 145 2.4 280 B82422A3681+100
0.82 1 22 30 140 2.5 240 B82422A3821+100

Closer tolerances and special versions on request.

Higher currents possible at temperatures <TR on request.
Sample kit available. Ordering code: B82422X100
For more information refer to chapter “Sample kits”.

1) Replace the + by the code letter for the required inductance tolerance.
For reel size ‡ 330 mm the last digit has to be an »8«. Example: B82422A3829K108
2) For Ni-barrier-plated terminals replace the last three digits “100” by “150” (reel 180 mm) or “158” (reel 330 mm).

Please read Cautions and warnings and

Important notes at the end of this document. 5 10/12
 SMT inductors, SIMID series B82422A*100
SIMID 1210-100

Characteristics and ordering codes

LR Tolerance fL Qmin fQ IR Rmax fres, min Ordering code 1)2)

PH MHz MHz mA : MHz (‡ 180-mm reel)

Core material: ferrite

1.0 r5% ^ J 1 20 7.96 380 0.34 320 B82422A1102+100
1.2 r10% ^ K 1 20 7.96 370 0.37 300 B82422A1122+100
1.5 1 20 7.96 340 0.50 270 B82422A1152+100
1.8 1 25 7.96 290 0.60 250 B82422A1182+100
2.2 1 25 7.96 270 0.75 125 B82422A1222+100
2.7 1 25 7.96 240 0.88 110 B82422A1272+100
3.3 1 27 7.96 200 1.20 110 B82422A1332+100
3.9 1 27 7.96 190 1.40 110 B82422A1392+100
4.7 1 27 7.96 150 2.20 110 B82422A1472+100
5.6 1 27 7.96 140 2.60 100 B82422A1562+100
6.8 1 27 7.96 135 2.80 90 B82422A1682+100
8.2 1 27 7.96 130 3.00 90 B82422A1822+100
10 1 27 2.52 180 1.60 25 B82422A1103+100
12 0.1 27 2.52 175 1.65 23 B82422A1123+100
15 0.1 27 2.52 165 1.85 20 B82422A1153+100
18 0.1 27 2.52 155 2.00 17 B82422A1183+100
22 0.1 27 2.52 140 2.65 16 B82422A1223+100
27 0.1 27 2.52 120 3.70 15 B82422A1273+100
33 0.1 27 2.52 105 4.50 13 B82422A1333+100
39 0.1 27 2.52 90 6.30 12 B82422A1393+100
47 0.1 27 2.52 85 7.00 11 B82422A1473+100
56 0.1 27 2.52 85 6.75 9 B82422A1563+100
68 0.1 27 2.52 80 7.70 9 B82422A1683+100
82 0.1 27 2.52 70 10.0 8 B82422A1823+100
100 0.1 27 2.52 65 11.5 7 B82422A1104+100

Closer tolerances and special versions on request.

Higher currents possible at temperatures <TR on request.
Sample kit available. Ordering code: B82422X100
For more information refer to chapter “Sample kits”.

1) Replace the + by the code letter for the required inductance tolerance.
For reel size ‡ 330 mm the last digit has to be an »8«. Example: B82422A1104K108
2) For Ni-barrier-plated terminals replace the last three digits “100” by “150” (reel 180 mm) or “158” (reel 330 mm).

Please read Cautions and warnings and

Important notes at the end of this document. 6 10/12
 SMT inductors, SIMID series B82422A*100
SIMID 1210-100

Impedance |Z| versus frequency f Inductance L versus DC load current IDC

measured with impedance analyzer measured with LCR meter Agilent 4285A,
Agilent E4991A, typical values at +20 °C typical values at +20 °C

Q factor versus frequency f Current derating Iop/IR

measured with impedance analyzer Agilent versus ambient temperature TA
E4991A, typical values at +20 °C (rated temperature TR = +125 °C)

7 10/12
 Cautions and warnings

■ Please note the recommendations in our Inductors data book (latest edition) and in the data
sheets.
– Particular attention should be paid to the derating curves given there.
– The soldering conditions should also be observed. Temperatures quoted in relation to wave
soldering refer to the pin, not the housing.
■ If the components are to be washed varnished it is necessary to check whether the washing
varnish agent that is used has a negative effect on the wire insulation, any plastics that are used,
or on glued joints. In particular, it is possible for washing varnish agent residues to have a
negative effect in the long-term on wire insulation.
Washing processes may damage the product due to the possible static or cyclic mechanical
loads (e.g. ultrasonic cleaning). They may cause cracks to develop on the product and its parts,
which might lead to reduced reliability or lifetime.
■ The following points must be observed if the components are potted in customer applications:
– Many potting materials shrink as they harden. They therefore exert a pressure on the plastic
housing or core. This pressure can have a deleterious effect on electrical properties, and in
extreme cases can damage the core or plastic housing mechanically.
– It is necessary to check whether the potting material used attacks or destroys the wire
insulation, plastics or glue.
– The effect of the potting material can change the high-frequency behaviour of the components.
■ Ferrites are sensitive to direct impact. This can cause the core material to flake, or lead to
breakage of the core.
■ Even for customer-specific products, conclusive validation of the component in the circuit can
only be carried out by the customer.

Please read Cautions and warnings and

Important notes at the end of this document. 8 10/12
 Important notes

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical
requirements that are often placed on our products in the areas of application concerned. We
nevertheless expressly point out that such statements cannot be regarded as binding
statements about the suitability of our products for a particular customer application. As
a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them
than the customers themselves. For these reasons, it is always ultimately incumbent on the
customer to check and decide whether an EPCOS product with the properties described in the
product specification is suitable for use in a particular customer application.

2. We also point out that in individual cases, a malfunction of electronic components or

failure before the end of their usual service life cannot be completely ruled out in the
current state of the art, even if they are operated as specified. In customer applications
requiring a very high level of operational safety and especially in customer applications in which
the malfunction or failure of an electronic component could endanger human life or health (e.g.
in accident prevention or life-saving systems), it must therefore be ensured by means of suitable
design of the customer application or other action taken by the customer (e.g. installation of
protective circuitry or redundancy) that no injury or damage is sustained by third parties in the
event of malfunction or failure of an electronic component.

3. The warnings, cautions and product-specific notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g.
because they are classed as hazardous). Useful information on this will be found in our
Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more
detailed questions, please contact our sales offices.

5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications
contained in this publication are still applicable before or when you place an order.

We also reserve the right to discontinue production and delivery of products.

Consequently, we cannot guarantee that all products named in this publication will always be
available. The aforementioned does not apply in the case of individual agreements deviating
from the foregoing for customer-specific products.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current version
of the “General Terms of Delivery for Products and Services in the Electrical Industry”
published by the German Electrical and Electronics Industry Association (ZVEI).

7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CeraLink, CSMP, CSSP, CTVS,
DeltaCap, DigiSiMic, DSSP, FilterCap, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC,
MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL,
SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap
are trademarks registered or pending in Europe and in other countries. Further information will
be found on the Internet at www.epcos.com/trademarks.

9 10/12