LC320EUH

Product Specification

SPECIFICATION
FOR
APPROVAL

( ) Preliminary Specification
( ● ) Final Specification

Title 32.0” WUXGA TFT LCD

BUYER General SUPPLIER LG.Display Co., Ltd.

MODEL *MODEL LC320EUH

SCA1
SUFFIX
(RoHS Verified)
*When you obtain standard approval,
please use the above model name without suffix

SIGNATURE SIGNATURE
APPROVED BY APPROVED BY
DATE DATE

/ P.Y. Kim / Team Leader

REVIEWED BY

/ T.H. Lee / Project Leader

PREPARED BY

/ Y.H. Lee / Engineer

Please return 1 copy for your confirmation with TV Products Development Dept.
your signature and comments. LG. Display LCD Co., Ltd

Ver. 1.0 0 /36

 LC320EUH
Product Specification

CONTENTS
Number ITEM Page
COVER 1

CONTENTS 2
RECORD OF REVISIONS 3

1 GENERAL DESCRIPTION 4

2 ABSOLUTE MAXIMUM RATINGS 5

3 ELECTRICAL SPECIFICATIONS 6

3-1 ELECTRICAL CHARACTERISTICS 6

3-2 INTERFACE CONNECTIONS 9

3-3 SIGNAL TIMING SPECIFICATIONS 12

3-4 DATA MAPPING AND TIMING 15

3-5 PANEL PIXEL STRUCTURE 16

3-6 POWER SEQUENCE 17

4 OPTICAL SPECIFICATIONS 18

5 MECHANICAL CHARACTERISTICS 22

6 RELIABILITY 25

7 INTERNATIONAL STANDARDS 26

7-1 SAFETY 26

7-2 ENVRONMENT 26

8 PACKING 27

8-1 DESIGNATION OF LOT MARK 27

8-2 PACKING FORM 27

9 PRECAUTIONS 28
9-1 MOUNTING PRECAUTIONS 28
9-2 OPERATING PRECAUTIONS 28
9-3 ELECTROSTATIC DISCHARGE CONTROL 29
9-4 PRECAUTIONS FOR STRONG LIGHT EXPOSURE 29
9-5 STORAGE 29
9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM 29

Ver. 1.0 1 /36

 LC320EUH
Product Specification

RECORD OF REVISIONS
Revision No. Revision Date Page Description
1.0 Jan, 08, 2010 - Final Specifications.

Ver. 1.0 2 /36

 LC320EUH
Product Specification

1. General Description
The LC320EUH is a Color Active Matrix Liquid Crystal Display with an integral Light Emitting Diode (LED)
bac k li ght s ys tem . T he m atr ix em p lo ys a- S i T hin F i lm T r ans is to r as the ac t i ve elem ent.
It is a transmissive type display operating in the normally black mode. It has a 31.55 inch diagonally measured
active dis pla y area wi th W UXGA resolution (1080 vertical by 1920 horizontal pixel array).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot.
Therefore, it can present a palette of more than 16.7M(true) colors.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color gamut,
high color depth and fast response time are important.

Power (VCC, VDD, VGH, VGL)

Source Control Signal Source Driver Circuit
Gate Control Signal CN1 S1 S1920
(60pin)
Gamma Reference Voltage G1
mini-LVDS (RGB) for Left drive

Power (VCC, VDD, VGH, VGL) TFT - LCD Panel

Source Control Signal (1920 × RGB × 1080 pixels)
[Gate In Panel]
Gate Control Signal CN2
(60pin)
Gamma Reference Voltage
G1080
mini-LVDS (RGB) for Right drive

V : 6Block
LED Anode CN1(12pin) H : 2Block
CN2 (13pin)
LED Cathode Local Dimming : 12 Block

General Features
Active Screen Size 31.55 inches(801.31mm) diagonal
Outline Dimension 741.4(H) x 435.8(V) x 10.8 mm(D) (Typ.)
Pixel Pitch 0.36375 mm x 0.36375 mm
Pixel Format 1920 horiz. by 1080 vert. Pixels, RGB stripe arrangement
Color Depth 8-bit, 16.7 M colors (※ 1.06B colors @ 10 bit (D) System Output )
Source D-IC : 8-bit mini-LVDS, gamma reference voltage, and control signals
Drive IC Data Interface
Gate D-IC : Gate In Panel
Luminance, White 450 cd/m2 (Center 1point ,Typ.)
Viewing Angle (CR>10) Viewing angle free ( R/L 178 (Min.), U/D 178 (Min.))
Power Consumption Total 73.2W (Typ.) (Logic=7.7W with T-CON, LED Backlight =65.5W )
Weight 6.3Kg (Typ.)
Display Mode Transmissive mode, Normally black
Surface Treatment Hard coating(3H), Anti-glare treatment of the front polarizer (Haze 10%)

Ver. 1.0 3 /36

 LC320EUH
Product Specification

2. Absolute Maximum Ratings

The following items are maximum values which, if exceeded, may cause faulty operation or damage to the
LCD module.
Table 1. ABSOLUTE MAXIMUM RATINGS
Value
Parameter Symbol Unit Note
Min Max
Logic Power Voltage VCC -0.5 +4.0 VDC
Gate High Voltage VGH +18.0 +30.0 VDC
Gate Low Voltage VGL -8.0 -4.0 VDC
Source D-IC Analog Voltage VDD -0.3 +18.0 VDC 1
Gamma Ref. Voltage (Upper) VGMH ½VDD-0.5 VDD+0.5 VDC
Gamma Ref. Voltage (Low) VGML -0.3 ½ VDD+0.5 VDC
LED Input Voltage VF - +180.0 VDC
Panel Front Temperature TSUR - +68 °C 4
Operating Temperature TOP 0 +50 °C
Storage Temperature TST -20 +60 °C
2,3
Operating Ambient Humidity HOP 10 90 %RH
Storage Humidity HST 10 90 %RH

Note: 1. Ambient temperature condition (Ta = 25 ± 2 °C )

2. Temperature and relative humidity range are shown in the figure below. Wet bulb temperature
should be Max 39 °C and no condensation of water.
3. Gravity mura can be guaranteed below 40℃ condition.
4. The maximum operating temperature is based on the test condition that the surface temperature
of display area is less than or equal to 68 ℃ with LCD module alone in a temperature controlled
chamber. Thermal management should be considered in final product design to prevent the surface
temperature of display area from being over 68 ℃. The range of operating temperature may
degrade in case of improper thermal management in final product design.
90%
60
60%

50 Storage
Wet Bulb
Temperature [°C]
40
Humidity
[(%)RH]

40%
Operation
30
20
10
0
10%

-20 0 10 20 30 40 50 60 70 80
Dry Bulb Temperature [°C]

Ver. 1.0 4 /36

 LC320EUH
Product Specification

3. Electrical Specifications
3-1. Electrical Characteristics
It requires several power inputs. The VCC is the basic power of LCD Driving power sequence, Which is used
to logic power voltage of Source D-IC and GIP.
Table 2. ELECTRICAL CHARACTERISTICS

Symbo Not
Parameter Condition MIN TYP MAX Unit
l e
Logic Power Voltage VCC - 3.0 3.3 3.6 VDC
Logic High Level Input Voltage VIH 2.7 VCC VDC
Logic Low Level Input Voltage VIL 0 0.6 VDC
Source D-IC Analog Voltage VDD - 15.8 16.0 16.2 VDC
Half Source D-IC Analog
H_VDD - 7.7 8.0 8.3 VDC 7
Voltage
VGMH (GMA1 ~ GMA9) ½*VDD VDD-0.2
Gamma Reference Voltage (GMA10 ~
VGML 0.2 ½*VDD
GMA18)
Normal 6.4 6.7 7.0 V
Common Voltage Vcom
Reverse 6.4 6.7 7.0 V
Mini-LVDS Clock frequency CLK 3.0V≤VCC ≤3.6V 312 MHz
mini-LVDS input Voltage (VCC-1.2)
VIB 0.7 + (VID/2) V
(Center) − VID / 2
mini-LVDS input Voltage
ΔVIB 0.8 V
Distortion (Center) Mini-LVDS Clock
5
mini-LVDS differential and Data
VID 150 800 mV
Voltage range
mini-LVDS differential
ΔVID 25 800 mV
Voltage range Dip
@ 25℃ 26.7 27 27.3 VDC
Gate High Voltage VGH
@ 0℃ 27.7 28 28.3
Gate Low Voltage VGL -5.2 -5.0 -4.8 VDC
VGI_P
GIP Bi-Scan Voltage - VGL - VGH VDC
VGI_N
VGH
GIP Refresh Voltage - VGL - VGH V
even/odd
GIP Start Pulse Voltage VST - VGL - VGH V
GIP Operating Clock GCLK - VGL - VGH V
Total Power Current ILCD - 640 835 mA 2
Total Power Consumption PLCD - 7.7 10.0 Watt 2
Note: 1. The specified current and power consumption are under the VLCD=12V., 25 ± 2°C, fV=120Hz
condition whereas mosaic pattern(8 x 6) is displayed and fV is the frame frequency.
2. The above spec is based on the basic model.
3. All of the typical gate voltage should be controlled within 1% voltage level
4. Ripple voltage level is recommended under 10%
5. In case of mini-LVDS signal spec, refer to Fig 2 for the more detail.
6. Logic Level Input Signal : SOE,POL,GSP,H_CONV,OPT_N
7. HVDD Voltage level is half of VDD and it should be between Gamma9 and Gamma10.

Ver. 1.0 5 /36

 LC320EUH
Product Specification

VGH

VGHM

GND

VGL
Without GPM With GPM

FIG. 1 Gate Output Wave form without GPM and with GPM

VID
△VID
△VIB
VCM (0V) VIB

△VID
VID
* Differential Probe * Active Probe

FIG. 2 Description of VID, ΔVIB, ΔVID

* Source PCB

FIG. 3 Measure point

Ver. 1.0 6 /36

 LC320EUH
Product Specification

Table 3. ELECTRICAL CHARACTERISTICS (Continue)

Values
Parameter Symbol Unit Note
Min Typ Max
Backlight Assembly :
Forward Current Anode IF (anode) 165 mAdc ±5%
(one array) Cathode IF (cathode) 52.25 55 57.75 mAdc 2, 3
Forward Voltage VF 92.8 99.2 105.6 Vdc 3
Forward Voltage Variation △VF 1.7 Vdc 5
Power Consumption PBL 61 65.5 70 W 6
Burst Dimming Duty On duty 1 100 %
Burst Dimming Frequency 1/T 95 182 Hz 8
LED Array : (APPENDIX-V)
Life Time 30,000 50,000 Hrs 7

The design of the LED driver must have specifications for the LED array in LCD Assembly.
Notes : The electrical characteristics of LED driver are based on Constant Current driving type.
The performance of the LED in LCM, for example life time or brightness, is extremely influenced by the
characteristics of the LED Driver. So, all the parameters of an LED driver should be carefully designed.
When you design or order the LED driver, please make sure unwanted lighting caused by the mismatch of the
LED and the driver (no lighting, flicker, etc) has never been occurred. When you confirm it, the LCD–
Assembly should be operated in the same condition as installed in your instrument.

1. Electrical characteristics are based on LED Array specification.

2. Specified values are defined for a Backlight Assembly. (IBL : 4 LED array, 165mA/LED array)
3. Each LED array has one anode terminal and three cathode terminals.
The forward current(IF) of the anode terminal is 165mA and it supplies 55mA into three strings, respectively
16 (LED Pakage / 1string)

Anode °°° Cathode #1

°°° Cathode #2
3 (LED String / 1 Array)
°°°

°°° Cathode #3

4. The forward voltage(VF) of LED array depends on ambient temperature (Appendix-Ⅲ)

5. ΔVF means Max VF-Min VF in one Backlight. So VF variation in a Backlight isn’t over Max. 1.7V
6. Maximum level of power consumption is measured at initial turn on.
Typical level of power consumption is measured after 1hrs aging at 25 ± 2°C.
7. The life time(MTTF) is determined as the time at which brightness of the LED is 50% compared to that of
initial value at the typical LED current on condition of continuous operating at 25 ± 2°C, based on duty 100%.
8. The reference method of burst dimming duty ratio.
It is recommended to use synchronous V-sync frequency to prevent waterfall
(Vsync x 1 =Burst Frequency)
Though PWM frequency is over 182Hz (max252Hz), function of backlight is not affected.

Ver. 1.0 7 /36

 LC320EUH
Product Specification

3-2. Interface Connections

This LCD module employs two kinds of interface connection, two 60-pin FFC connector are used for the
module electronics and 12-pin,13-pin connectors are used for the integral backlight system.
3-2-1. LCD Module
-LCD Connector (CN1): TF06L-60S-0.5SH (Manufactured by HRS) or Equivalent

Table 4-1. MODULE CONNECTOR(CN1) PIN CONFIGURATION

No Symbol Description No Symbol Description
1 GND Ground 31 LLV3 - Left Mini LVDS Receiver Signal(3-)
2 LTD_OUT LTD OUTPUT 32 LLV3 + Left Mini LVDS Receiver Signal(3+)
3 GCLK1 GIP GATE Clock 1 33 LCLK - Left Mini LVDS Receiver Clock Signal(-)
4 GCLK2 GIP GATE Clock 2 34 LCLK + Left Mini LVDS Receiver Clock Signal(+)
5 GCLK3 GIP GATE Clock 3 35 LLV2 - Left Mini LVDS Receiver Signal(2-)
6 GCLK4 GIP GATE Clock 4 36 LLV2 + Left Mini LVDS Receiver Signal(2+)
7 GCLK5 GIP GATE Clock 5 37 LLV1 - Left Mini LVDS Receiver Signal(1-)
8 GCLK6 GIP GATE Clock 6 38 LLV1 + Left Mini LVDS Receiver Signal(1+)
9 VGI_N GIP Bi-Scan (Normal =VGL Rotate = VGH) 39 LLV0 - Left Mini LVDS Receiver Signal(0-)
10 VGI_P GIP Bi-Scan (Normal =VGH Rotate = VGL) 40 LLV0 + Left Mini LVDS Receiver Signal(0+)
11 VGH_ODD GIP Panel VDD for Odd GATE TFT 41 GND Ground
12 VGH_EVEN GIP Panel VDD for Even GATE TFT 42 SOE Source Output Enable SIGNAL
13 VGL GATE Low Voltage 43 POL Polarity Control Signal
14 VST VERTICAL START PULSE 44 GSP GATE Start Pulse
15 GND Ground 45 H_CONV "H“ H 2dot Inversion/ "L" H 1dot Inversion
16 VCOM_L_FB VCOM Left Feed-Back Output 46 OPT_N “H” Normal Display / “L” Rotation Display
17 VCOM_L VCOM Left Input 47 GND Ground
18 GND Ground 48 GMA 18 GAMMA VOLTAGE 18 (Output From LCD)
19 VDD Driver Power Supply Voltage 49 GMA 16 GAMMA VOLTAGE 16
20 VDD Driver Power Supply Voltage 50 GMA 15 GAMMA VOLTAGE 15
21 H_VDD Half Driver Power Supply Voltage 51 GMA 14 GAMMA VOLTAGE 14
22 H_VDD Half Driver Power Supply Voltage 52 GMA 12 GAMMA VOLTAGE 12
23 GND Ground 53 GMA 10 GAMMA VOLTAGE 10 (Output From LCD)
24 VCC Logic Power Supply Voltage 54 GMA 9 GAMMA VOLTAGE 9 (Output From LCD)
25 VCC Logic Power Supply Voltage 55 GMA 7 GAMMA VOLTAGE 7
26 GND Ground 56 GMA 5 GAMMA VOLTAGE 5
27 LLV5 - Left Mini LVDS Receiver Signal(5-) 57 GMA 4 GAMMA VOLTAGE 4
28 LLV5 + Left Mini LVDS Receiver Signal(5+) 58 GMA 3 GAMMA VOLTAGE 3
29 LLV4 - Left Mini LVDS Receiver Signal(4-) 59 GMA 1 GAMMA VOLTAGE 1 (Output From LCD)
30 LLV4 + Left Mini LVDS Receiver Signal(4+) 60 GND Ground

Note : 1. Please refer to application note for details.

(GIP & Half VDD & Gamma Voltage & H_CONV setting)
2. These 'input signal' (OPT_N,H_CONV) should be connected

Ver. 1.0 8 /36

 LC320EUH
Product Specification

-LCD Connector (CN2): TF06L-60S-0.5SH (Manufactured by HRS) or Equivalent

Table 4-2. MODULE CONNECTOR(CN2) PIN CONFIGURATION

No Symbol Description No Symbol Description
1 GND Ground 31 RLV1 - Right Mini LVDS Receiver Signal(1-)
2 GMA 1 GAMMA VOLTAGE 1 (Output From LCD) 32 RLV1 + Right Mini LVDS Receiver Signal(1+)
3 GMA 3 GAMMA VOLTAGE 3 33 RLV0 - Right Mini LVDS Receiver Signal(0-)
4 GMA 4 GAMMA VOLTAGE 4 34 RLV0 + Right Mini LVDS Receiver Signal(0+)
5 GMA 5 GAMMA VOLTAGE 5 35 GND Ground
6 GMA 7 GAMMA VOLTAGE 7 36 VCC Logic Power Supply Voltage
7 GMA 9 GAMMA VOLTAGE 9 (Output From LCD) 37 VCC Logic Power Supply Voltage
8 GMA 10 GAMMA VOLTAGE 10 (Output From LCD) 38 GND Ground
9 GMA 12 GAMMA VOLTAGE 12 39 H_VDD Half Driver Power Supply Voltage
10 GMA 14 GAMMA VOLTAGE 14 40 H_VDD Half Driver Power Supply Voltage
11 GMA 15 GAMMA VOLTAGE 15 41 VDD Driver Power Supply Voltage
12 GMA 16 GAMMA VOLTAGE 16 42 VDD Driver Power Supply Voltage
13 GMA 18 GAMMA VOLTAGE 18 (Output From LCD) 43 GND Ground
14 GND Ground 44 VCOM_R VCOM Right Input
15 OPT_N “H” Normal Display / “L” Rotation Display 45 VCOM_R_FB VCOM Right Feed-Back Output
16 H_CONV "H“ H 2dot Inversion/ "L" H 1dot Inversion 46 GND Ground
17 GSP GATE Start Pulse 47 VST VERTICAL START PULSE
18 POL Polarity Control Signal 48 VGL GATE Low Voltage
19 SOE Source Output Enable SIGNAL 49 VGH_EVEN GIP Panel VDD for Even GATE TFT
20 GND Ground 50 VGH_ODD GIP Panel VDD for Odd GATE TFT
21 RLV5 - Right Mini LVDS Receiver Signal(5-) 51 VGI_P GIP Bi-Scan (Normal =VGH Rotate = VGL)
22 RLV5 + Right Mini LVDS Receiver Signal(5+) 52 VGI_N GIP Bi-Scan (Normal =VGL Rotate = VGH)
23 RLV4 - Right Mini LVDS Receiver Signal(4-) 53 GCLK6 GIP GATE Clock 6
24 RLV4 + Right Mini LVDS Receiver Signal(4+) 54 GCLK5 GIP GATE Clock 5
25 RLV3 - Right Mini LVDS Receiver Signal(3-) 55 GCLK4 GIP GATE Clock 4
26 RLV3 + Right Mini LVDS Receiver Signal(3+) 56 GCLK3 GIP GATE Clock 3
27 LCLK - Right Mini LVDS Receiver Clock Signal(-) 57 GCLK2 GIP GATE Clock 2
28 LCLK + Right Mini LVDS Receiver Clock Signal(+) 58 GCLK1 GIP GATE Clock 1
29 RLV2 - Right Mini LVDS Receiver Signal(2-) 59 LTD_OUT LTD OUTPUT
30 RLV2 + Right Mini LVDS Receiver Signal(2+) 60 GND Ground

Note : 1. Please refer to application note for details

(GIP & Half VDD & Gamma Voltage & H_CONV setting)
2. These 'input signal' (OPT_N,H_CONV) should be connected

CN 2 CN 1
Source Right PCB Source Left PCB
#1 #60 #1 #60

Ver. 1.0 9 /36

 LC320EUH
Product Specification

3-2-2. Backlight Module

[ CN1 ] [ CN2 ]
1) LED Array assy Connector (Plug) 1) LED Array assy Connector (Plug)
: 20010HS-12 (manufactured by Yeonho)or equivalent : 20010HS-13(BK) (manufactured by Yeonho)or equivalent
2) Mating Connector (Receptacle) 2) Mating Connector (Receptacle)
: 20010WR-12 (manufactured by Yeonho)or equivalent : 20010WR-13(BK) (manufactured by Yeonho)or equivalent

Table 5. BACKLIGHT CONNECTOR PIN CONFIGURATION(CN1,CN2)

No Symbol Description Note No Symbol Description Note

1 #1 Anode LED Input Current 1 #3 Anode LED Input Current

2 N.C Open 2 N.C Open

3 #1-1 Cathode LED Output Current 3 #3-1 Cathode LED Output Current

4 #1-2 Cathode LED Output Current 4 #3-2 Cathode LED Output Current

5 #1-3 Cathode LED Output Current 5 #3-3 Cathode LED Output Current

6 N.C Open 6 N.C Open

7 N.C Open 7 N.C Open

8 #2-3Cathode LED Output Current 8 N.C Open

9 #2-2 Cathode LED Output Current 9 #4-3Cathode LED Output Current

10 #2-1 Cathode LED Output Current 10 #4-2 Cathode LED Output Current

11 N.C Open 11 #4-1 Cathode LED Output Current

12 #2 Anode LED Input Current 12 N.C Open

13 #4 Anode LED Input Current

◆ Rear view of LCM

Ver. 1.0 10 /36

 LC320EUH
Product Specification

3-3. Signal Timing Specifications

Table 6. Timing Requirements

Parameter Symbol Condition Min Typ Max Unit Note

Mini Clock pulse period T1 3.2 3.4 ns

Mini Clock pulse low period T2 1.6 - - ns

Mini Clock pulse high period T3 1.6 - - ns 1

Mini Data setup time T6 0.6 - - ns

Mini Data hold time T7 0.6 - - ns

Reset low to SOE rising time T8 0 - - ns

SOE to Reset input time T9 200 - - ns

CLK
Receiver off to SOE timing T10 10 - -
cycle

POL signal to SOE setup time T11 -5 - - ns

POL signal to SOE hold time T12 6 - - ns

CLK
Reset High Period T13 3
cycle

SOE signal GSP setup time T14 100 ns

SOE signal GSP Hold time T15 100 ns

SOE signal Pulse Width T16 200 ns

Note : 1. Mini-LVDS timing measure conditions

: 268MHz < Clock Frequency < 312MHz , 150mV < VID < 800mV @ 3.0<VCC<3.3
2. Setup time and hold time should be satisfied at the same time
T1
T3 T2

CLK- 70% 70%

VDIFF
30% 30%
CLK+

T6 T7 T6 T7 T5 T4
LV0+, - 70% 70%
to 50% VDIFF
30% 30%
LV5+,-

T5 T4

FIG 4. Source D-IC Input Data Latch Timing Waveform

Ver. 1.0 11 /36

 LC320EUH
Product Specification

Read The Reset=H Read The Reset=L 1st DATA

T1

T2

CLK+
T3

NA R=L R=L R=H R=H R=H NA R=L NA D D D D D

LV0+,-
T13
LV1+,-
to NA NA NA NA NA NA NA NA NA D D D D D

LV5+,- T8 T9

70%
SOE 30%

FIG 5-1. Input Data Timing for 1st Source D-IC Chip

Last DATA

(640) (641)
CLK+

LV0+,- D D D NA NA NA NA NA NA R=L R=L R=L

LV1+,-
to D D D NA NA NA NA NA NA NA NA NA
LV5+,-
T8

70%

SOE 30%

T10

FIG 5-2. Last Data Latch to SOE Timing

Ver. 1.0 12 /36

 LC320EUH
Product Specification

T14 T15
T11 T12
70% 70%

30% 30%
SOE

70% 70%
POL 30% 30%

70% 70%

GSP

GSP

T16

SOE

1st line data 1st line output

FIG 6. POL, GSP and SOE Timing Waveform

Ver. 1.0 13 /36

 LC320EUH
Product Specification

3-4. Data Mapping and Timing

Display data and control signal (RESET) are input to LV0 to LV5.

3-4-1. Control signal input mode

CLK +

LV0 + RESET RESET RESET RESET RESET RESET RESET RESET RESET RESET

3-4-2. Display data input mode

CLK+

LV0+ D00 D01 D02 D03 D04 D05 D06 D07 D00

LV1+ D10 D11 D12 D13 D14 D15 D16 D17 D10

LV2+ D20 D21 D22 D23 D24 D25 D26 D27 D20

LV3+ D30 D31 D32 D33 D34 D35 D36 D37 D30

LV4+ D40 D41 D42 D43 D44 D45 D46 D47 D40

LV5+ D50 D51 D52 D53 D54 D55 D56 D57 D50

DATA INPUT CYCLE

Fig. 7 Mini-LVDS Data

Note : 1. For data mapping, please refer to panel pixel structure Fig.8

Ver. 1.0 14 /36

 LC320EUH
Product Specification

3-5. Panel Pixel Structure

D1 D2 D3 D4 D5 D1918 D1919 D1920 D1921

G1

G2

G3

G4

G5

G6

G1078

G1079

G1080

FIG. 8 Panel Pixel Structure

Ver. 1.0 15 /36

 LC320EUH
Product Specification

3-6. Power Sequence

3-6-1. LCD Driving circuit

70%
Power Supply For LCD VCC 0V
VGH
T2 T7
Power Supply For LCD 90%
VDD, HVDD,VGH, Gamma Ref.
Voltage
0V
Power Supply For LCD 50%
VGL 100%
T1

VGH T3
GIP Signal For LCD
even/Odd ..
T4
VST ..
T5 ..
GCLK1~6

T6 T6’
LED on
Power For LED

Table 7. POWER SEQUENCE Ta= 25±2°C, fV=120Hz, Dclk=74.25MHz

Value
Parameter Unit Notes
Min Typ Max
T1 0.5 - ms
T2 0.5 - ms
T3 0 - ms
T4 10 - ms 2
T5 0 - ms
T6 / T6’ 20 - ms
T7 2 - sec
Note : 1. Power sequence for Source D-IC must follow the Case1 & 2.
※ Please refer to Appendix V for more details.
2. VGH Odd signal should be started “High” status and VGH even & odd can not be “High at the
same time.
3. Power Off Sequence order is reverse of Power On Condition including Source D-IC.
4. GCLK On/Off Sequence
Normal : GCLK4
GCLK5
GCLK6
GCLK1
GCLK2
GCLK3.
Reverse : GCLK3
GCLK2
GCLK1
GCLK6
GCLK5
GCLK4.
5. VDD_odd/even transition time should be within V_blank
Ver. 1.0 16 /36
 LC320EUH
Product Specification

4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at
25±2°C. The values are specified at an approximate distance 50cm from the LCD surface at a viewing angle
of Φ and θ equal to 0 °.
It is presented additional information concerning the measurement equipment and method in FIG. 9.
LCD Module Pritchard 880 or
Optical Stage(x,y)
equivalent

50cm
FIG. 9 Optical Characteristic Measurement Equipment and Method
Ta= 25±2°C, VDD,H_VDD,VGH,VGL=typ,
Table 8. OPTICAL CHARACTERISTICS fV=120Hz, Clk=297MHz, IF = 165mA (Typ)
Value
Parameter Symbol Unit Note
Min Typ Max
Contrast Ratio CR 900 1300 - 1
Surface Luminance, white LWH 360 450 - cd/m2 2
Luminance Variation δ WHITE 5P - - 1.3 3

Rising Tr - 8 12
Response Time ms 4
Falling Tf - 10 14

Rx 0.651
RED
Ry 0.332
Gx 0.308
GREEN
Color Coordinates Gy Typ 0.597 Typ
[CIE1931] Bx -0.03 0.149 +0.03
BLUE
By 0.059
Wx 0.279
WHITE
Wy 0.292
Color Temperature 10,000 K
Color Gamut 72 %
Viewing Angle (CR>10)
x axis, right(φ=0°) θr 89 - -
x axis, left (φ=180°) θl 89 - -
degree 5
y axis, up (φ=90°) θu 89 - -
y axis, down (φ=270°) θd 89 - -
Gray Scale - - - 6

Ver. 1.0 17 /36

 LC320EUH
Product Specification

Note : 1. Contrast Ratio(CR) is defined mathematically as :

Surface Luminance at all white pixels
CR =
Surface Luminance at all black pixels
It is measured at center 1-point.

2. Surface luminance is determined after the unit has been ‘ON’ and 1Hour after lighting the
backlight in a dark environment at 25±2°C. Surface luminance is the luminance value at center
1-point across the LCD surface 50cm from the surface with all pixels displaying white.
For more information see the FIG. 10.

3. The variation in surface luminance , δ WHITE is defined as :

δ WHITE(5P) = Maximum(Lon1,Lon2, Lon3, Lon4, Lon5) / Minimum(Lon1,Lon2, Lon3, Lon4, Lon5)
Where Lon1 to Lon5 are the luminance with all pixels displaying white at 5 locations .
For more information, see the FIG. 10.

4. Response time is the time required for the display to transit from G(255) to G(0) (Rise Time, TrR)
and from G(0) to G(255) (Decay Time, TrD).

5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD module surface. For more information, see the FIG. 12.

6. Gray scale specification

Gamma Value is approximately 2.2. For more information, see the Table 9.
Table 9. GRAY SCALE SPECIFICATION
Gray Level Luminance [%] (Typ) Gray Level Gamma Ref.

L0 0.077 L0 Gamma9
L15 0.28 L1 -
L31 1.05
L31 Gamma7
L47 2.50
L63 4.69 Positive L63 -
Voltage L127 Gamma5
L79 7.67
L95 11.47 L191 Gamma4
L111 16.11 L223 Gamma3
L127 21.64 L255 Gamma1
L143 28.07
L255 Gamma18
L159 35.43
L223 Gamma16
L175 43.73
L191 52.99 L191 Gamma15
L207 63.23 Negative L127 Gamma14
L223 74.47 Voltage L63 -
L239 86.72 L31 Gamma12
L255 100 L1 -
L0 Gamma10

Ver. 1.0 18 /36

 LC320EUH
Product Specification

Measuring point for surface luminance & luminance variation

H
A

② ③

①
V
B

A : H / 4 mm
④ ⑤ B : V / 4 mm
@ H,V : Active Area

FIG. 10 5 Points for Luminance Measure

Response time is defined as the following figure and shall be measured by switching the input signal for
“Gray(N)” and “Gray(M)”.

T rR T rD
100
90

Optical
Response

10
Gray(N) Gray(M) Gray(N)
0
N,M = Black~White, N<M

FIG. 11 Response Time

Ver. 1.0 19 /36

 LC320EUH
Product Specification

Dimension of viewing angle range

Normal
E Y
φ = 90 ° , Up

φ = 180 ° , Left
θ

φ = 0 ° , Right

φ = 270 ° , Down

FIG.12 Viewing Angle

Ver. 1.0 20 /36

 LC320EUH
Product Specification

5. Mechanical Characteristics

Table 10 provides general mechanical characteristics.

Table 10. MECHANICAL CHARACTERISTICS

Item Value

Horizontal 741.4 mm

Outline Dimension Vertical 435.8 mm

Depth 10.8 mm

Horizontal 705.4 mm
Bezel Area
Vertical 399.8 mm

Horizontal 698.40 mm
Active Display Area
Vertical 392.85 mm

Weight 6.3 Kg (Typ.) , 7.0 Kg (Max.)

Note : Please refer to a mechanical drawing in terms of tolerance at the next page.

Ver. 1.0 21 /36

 LC320EUH
Product Specification

[ FRONT VIEW ]

Ver. 1.0 22 /36

 LC320EUH
Product Specification

[ REAR VIEW ]

Ver. 1.0 23 /36

 LC320EUH
Product Specification

6. Reliability
Table 11. ENVIRONMENT TEST CONDITION

No. Test Item Condition

1 High temperature storage test Ta= 60°C 240h

2 Low temperature storage test Ta= -20°C 240h

3 High temperature operation test Ta= 50°C 50%RH 240h

4 Low temperature operation test Ta= 0°C 240h

Wave form : random

Vibration level : 1.0Grms
Vibration test
5 Bandwidth : 10-300Hz
(non-operating)
Duration : X,Y,Z, 30 min
Each direction per 10 min

Shock level : 100Grms

Shock test Waveform : half sine wave, 2ms
6
(non-operating) Direction : ±X, ±Y, ±Z
One time each direction

7 Humidity condition Operation Ta= 40 °C ,90%RH

Altitude operating 0 - 15,000 ft

8
storage / shipment 0 - 40,000 ft

Note : Before and after Reliability test, LCM should be operated with normal function.

Ver. 1.0 24 /36

 LC320EUH
Product Specification

7. International Standards
7-1. Safety
a) UL 60065, Seventh Edition, Underwriters Laboratories Inc.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
b) CAN/CSA C22.2 No.60065:03, Canadian Standards Association.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
c) EN 60065:2002 + A11:2008, European Committee for Electrotechnical Standardization (CENELEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
d) IEC 60065:2005 + A1:2005, The International Electrotechnical Commission (IEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
(Including report of IEC60825-1:2001 clause 8 and clause 9)
Notes
1. Laser (LED Backlight) Information

Class 1M LED Product

IEC60825-1 : 2001
Embedded LED Power (Class1M)
Power : 6.5896 mW (Max.)
Wavelength : 277 ~526 (nm)
Width : 1.6 x 0.6 (mm)

2. Caution
: LED inside.
Class 1M laser (LEDs) radiation when open.
Do not open while operating.

7-2. Environment
a) RoHS, Directive 2002/95/EC of the European Parliament and of the council of 27 January 2003 on the
restriction of the use of certain hazardous substances in electrical and electronic equipment

Ver. 1.0 25 /36

 LC320EUH
Product Specification

8. Packing
8-1. Information of LCM Label
a) Lot Mark

A B C D E F G H I J K L M

A,B,C : SIZE(INCH) D : YEAR

E : MONTH F ~ M : SERIAL NO.

Note
1. YEAR
Year 2001 2002 2003 2004 2005 2006 2007 2008 2009 2010

Mark 1 2 3 4 5 6 7 8 9 0

2. MONTH

Month Jan Feb Mar Apr May Jun Jul Aug Sep Oct Nov Dec

Mark 1 2 4 4 5 6 7 8 9 A B C

b) Location of Lot Mark

Serial NO. is printed on the label. The label is attached to the backside of the LCD module.
This is subject to change without prior notice.

8-2. Packing Form

a) Package quantity in one Pallet : 6 pcs

b) Pallet Size : 1140 mm X 870 mm X 1161 mm.

Ver. 1.0 26 /36

 LC320EUH
Product Specification

9. Precautions
Please pay attention to the followings when you use this TFT LCD module.

9-1. Mounting Precautions

(1) You must mount a module using specified mounting holes (Details refer to the drawings).
(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to
the module. And the case on which a module is mounted should have sufficient strength so that external
force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature specification.
(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break
by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzine. Normal-hexane is recommended for cleaning the adhesives
used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause
chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.

9-2. Operating Precautions

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :
V=±200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on)
becomes longer
(4) Be careful for condensation at sudden temperature change.Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smear or spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.
(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference.
(7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can’t be operated
its full characteristics perfectly.
(8) A screw which is fastened up the steels should be a machine screw.
(if not, it can causes conductive particles and deal LCM a fatal blow)
(9) Please do not set LCD on its edge.
(10) The conductive material and signal cables are kept away from LED driver inductor to prevent abnormal
display, sound noise and temperature rising.

Ver. 1.0 27 /36

 LC320EUH
Product Specification

9-3. Electrostatic Discharge Control

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that
treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4. Precautions for Strong Light Exposure

Strong light exposure causes degradation of polarizer and color filter.

9-5. Storage
When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.

9-6. Handling Precautions for Protection Film

(1) The protection film is attached to the bezel with a small masking tape.
When the protection film is peeled off, static electricity is generated between the film and polarizer.
This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-
blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very
small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-
hexane.

Ver. 1.0 28 /36

 LC320EUH
Product Specification

# APPENDIX-I-1
■ LC320EUH-SCA1 - Pallet Ass’y

NO. DESCRIPTION MATERIAL

1 PACKING ASS’Y

2 PALLET Plywood

3 BAND PP
4 CLIP, BAND STEEL
5 Angle Cover PAPER

6 WRAP LDPE

7 LABEL ART 100X70

Ver. 1.0 29 /36

 LC320EUH
Product Specification

# APPENDIX-I-2
■ LC320EUH-SCA1 - Packing Ass’y

NO. DESCRIPTION MATERIAL

1 LCD Module

2 BAG AL

3 TAPE MASKING 20MMX50M

4 Packing EPS

5 Packing EPS

6 BOX PAPER_DW3

7 TAPE OPP 70MMX300M

8 Label ART 100X70

Ver. 1.0 30 /36

 LC320EUH
Product Specification

# APPENDIX-II-1
■ LC320EUH-SCA1 - LCM Label

Model
LC320EUH
(SC)(A1)

Serial No.
UL, TUV Mark
LGD Logo
US PATENT No. Origin

Ver. 1.0 31 /36

 LC320EUH
Product Specification

# APPENDIX-II-2
■ LC320EUH-SCA1 - Pallet Label

LC320EUH
SCA1
6 PCS 001/01-01
MADE IN KOREA RoHS Verified

XXXXXXXXXXXXX XXX

Ver. 1.0 32 /36

 LC320EUH
Product Specification

# APPENDIX- III
■ LED Array Electrical Spec

■ Forward Current vs. Forward Voltage

■ Ambient Temperature vs. Forward Voltage

Ver. 1.0 33 /36

 LC320EUH
Product Specification

Ⅳ
# APPENDIX-Ⅳ
■ Local Dimming Block Pin Matching

#4-
#4-1 #4-
#4-2 #4-
#4-3 #3-
#3-3 #3-
#3-2 #3-
#3-1
[ CN2 ] [ CN1]
Pin No Block T-con Front Pin No Block
1 Vo_2 1 Vo_1
2 N.C A1 A2 A3 A4 A5 A6 2 N.C
3 A6 3 B1
4 A5 4 B2
5 A4 5 B3
6 N.C 6 N.C
7 N.C B1 B2 B3 B4 B5 B6 7 N.C
8 N.C 8 B4
9 A3 9 B5
10 A2 10 B6
#1-
#1-1 #1-
#1-2 #1-
#1-3 #2-
#2-3 #2-
#2-2 #2-
#2-1
11 A1 11 N.C
12 N.C 12 Vo_1
13 Vo_2 #2-
#2-1 #2-
#2-2 #2-
#2-3 #1-
#1-3 #1-
#1-2 #1-
#1-1

Front

B6 B5 B4 B3 B2 B1

A6 A5 A4 A3 A2 A1

T-con
#3-
#3-1 #3-
#3-2 #3-
#3-3 #4-
#4-3 #4-
#4-2 #4-
#4-1

Ver. 1.0 34 /36

 LC320EUH
Product Specification

# APPENDIX-V
■ LC320EUH-SCA1-Source D-IC Power Sequence

- Input Signal : SOE,POL,GSP,H_CONV,OPT_N

Ver. 1.0 35 /36