SIPROTEC 5

Configuration
Jun 25, 2020 3:57 PM

Device: 7UT85 Transf. Prot (2 Wind.)

Product code
Short: P1F487069
Long: 7UT85-DAAA-AA0-0AAAA0-AF0111-12111B-BAA000-000AC0-CC1BA1-CP1CG0

Firmware: Current version

Housing width: 2/3 x 19''
Housing type: Flush mounting
Binary inputs: 25
Binary outputs: 20 Relays (11 Standard, 9 Fast, 0 High-Speed, 0 Power)
Current transformers: 12 for protection
Voltage transformers: 4 standard
Measuring-transducer inputs: 0 (20 mA or 10 V, fast)
0 (20 mA, standard)
CPU: CP300
Modules in 19" row 1: IO203 , PS201 , IO214 , IO207
Modules in 19" row 2:
LEDs/Push-buttons: 16 LEDs
Operation Panel: Integrated
Key switch: Without
Display type: Small display
Front Design: Standard
Power Supply: DC 60 V-250 V, AC 100 V-230 V
Redundant Power Supply: No

Communication/Plug-in modules:
Communications encryption: Normal
Integrated Ethernet port J: for DIGSI 5
Plug-in module position E: ETH-BB-2FO: 2x optical Ethernet 100 Mbit/s, 1300 nm, duplex LC connector,
2 km over 50/125 um or 62.5/125 um multimode optical fiber Communication
Protocols: applicable for DIGSI 5, IEC 61850-8-1 MMS and GOOSE, IEC
60870-5-104, DNP3 TCP, Modbus TCP, Synchrophasor (IEEE C37.118 - IP),
Profinet IO, SUP, DHCP, SNTP, SNMP, etc. Redundancy protocols: Line Mode,
RSTP, HSR, PRP
Plug-in module position F: Port is available but not assembled
SIPROTEC 5
Configuration
Jun 25, 2020 3:57 PM

Functions:
Function points class: Base + 50 function points

Note on function-points class

The function-points class results from the sum of the function points of the selected functions. You can apply these
functions as selected. The device allows also each other selection of functions as long as the sum of the required
function points is within the selected function-points class. With the maximum function-points class of 1400 it is
possible to activate all the functions in the device. The function-points exceeding 1400 are free of charge. In the
engineering phase DIGSI 5 checks that the selected configuration is suitable (capable of running in the device) before
loading it to the device.

Miscellaneous:
Warranty: 5 years
Firmware: Current version
SIPROTEC 5
Configuration
Jun 25, 2020 3:57 PM

Functional scope 7UT85 Transf. Prot (2 Wind.):

Always Add selected Result
ANSI Function Abbr. included Qty. x Value = Points Qty.
Hardware quantity structure expandable I/O

Process Bus Client Protocol (Note: This PB client x 100 =

function requires at least one dedicated
ETH-BD-2FO plug-in module, with
V8.0)
IEC61850-9-2 Merging Unit stream MU x 200 =
(Note: This function requires a
dedicated ETH-BD-2FO per stream,
with V8.0)
21/21N Distance protection Z<, V< / x 100 =
I>/(V,I)
21T Impedance protection for transformers Z< x 25 =
24 Overexcitation protection V/f x 25 =
25 Synchrocheck, synchronization function Sync x 50 =
32, 37 Power protection active/reactive power P<>, x 10 =
Q<>
27 Undervoltage protection: "3-phase" V< x 5 =
or "positive-sequence system V1" or
"universal Vx"
Undervoltage-controlled reactive power Q>/V< x 5 =
protection
32R Reverse-power protection - P< 2x x 5 = 2x
37 Undercurrent I<

37 Power-plant disconnection protection -dP x 50 =

38 Temperature supervision >

46 Negative-sequence overcurrent I2> x 5 =

protection
46 Unbalanced-load protection (thermal) I2² t> x 5 =
47 Overvoltage protection, negative- V2> x 5 =
sequence system
47 Overvoltage protection, negative- V2/V1> x 5 =
sequence/positive-sequence system
49 Thermal overload protection , I²t

49 Thermal overload protection, user- , I²t

defined characteristic
SIPROTEC 5
Configuration
Jun 25, 2020 3:57 PM

Functional scope 7UT85 Transf. Prot (2 Wind.):

Always Add selected Result
ANSI Function Abbr. included Qty. x Value = Points Qty.
49H Hot spot calculation h, I²t x 20 =
50N/ Overcurrent protection, ground IN>
51N TD
50/51 Overcurrent protection, phases I> 3x x 30 = 3x
TD
Instantaneous tripping at switch onto SOTF x 10 =
fault
50HS Instantaneous high-current tripping I>>>

50/51 Overcurrent protection with positive- I1>

TD sequence current I1 (from V7.9)
50N/ Overcurrent protection, 1-phase IN>
51N TD
50Ns/ Sensitive ground-current detection INs> x 5 =
51Ns for systems with resonant or isolated
neutral systems incl. a) 3I0>, b)
admittance Y0>, c) 3I0-harm> (from
V7.8)
Ground-fault detection via pulse pattern IN-pulse x 15 =
detection; Note: this stage additionally
requires the function 50Ns/51Ns or
67Ns "Sensitive ground-fault detection
for systems with resonant or isolated
neutral"
Intermittent ground-fault protection Iie> x 20 =
50BF Circuit-breaker failure protection, 3-pole CBFP x 5 =
50RS Circuit-breaker restrike protection CBRS x 20 =
51V Overcurrent protection, voltage t=f(I,V) x 10 =
dependent
59, 59N Overvoltage protection: "3-phase" V> x 5 =
or "zero-sequence system V0" or
"universal Vx"
59 Overvoltage protection: "3-phase" V> x 5 =
or "positive-sequence system V1" or
"universal Vx"
60 Voltage-comparison supervision U> x 5 =
67 Directional overcurrent protection, I>, (V,I) x 5 =
phases
SIPROTEC 5
Configuration
Jun 25, 2020 3:57 PM

Functional scope 7UT85 Transf. Prot (2 Wind.):

Always Add selected Result
ANSI Function Abbr. included Qty. x Value = Points Qty.
67N Directional overcurrent protection for IN>, (V,I) x 30 =
ground faults in grounded systems
67N Directional overcurrent protection, IN>, (V,I) x 15 =
ground
67Ns Dir. sensitive ground-fault detection x 30 =
for systems with resonant or isolated
neutral incl. a) 3I0>, b) V0>, c) Cos-/
SinPhi, d) Transient ground-fault fct., e)
Phi(V,I), f) admittance
Directional stage with a harmonic; (V0h,I0h) x 10 =
Note: this stage additionally requires
the function "67Ns Dir. sensitive
ground-fault detection for systems with
resonant or isolated neutral"
Directional intermittent ground-fault Iie dir> x 20 =
protection
68 Power-swing blocking Z/t x 25 =
74TC Trip-circuit supervision TCS

74CC Closed-circuit supervision (from V7.9) CCS

79 Automatic reclosing, 3-pole AR x 45 =

81 Frequency protection: "f>" or "f<" or "df/ f<>; df/ x 5 =
dt" dt<>
81U Underfrequency load-shedding f<(UFLS) x 15 =
85/21 Teleprotection for distance protection

85/27 Weak or no infeed: echo and tripping WI

81 AF Abnormal frequency protection fBand x 15 =

Vector-jump protection > x 20 =
85/67N Teleprotection for directional ground
fault protection
86 Lockout

87T Transformer differential protection I

87T Differential protection for special I x 150 =

transformers
87T Differential protection (Node protection I Node
Node for auto transformer)
SIPROTEC 5
Configuration
Jun 25, 2020 3:57 PM

Functional scope 7UT85 Transf. Prot (2 Wind.):

Always Add selected Result
ANSI Function Abbr. included Qty. x Value = Points Qty.
87T Transformer differential protection for I x 200 =
phase angle regulating transformer
(single core)
87N T Restricted ground-fault protection IN x 15 =
87M Motor differential protection I

87G Generator differential protection I x 50 =

87L Differential protection for lines with 2 I x 170 =
ends for 7UT8 (communication with
7SD82,85,86, 7SL86,87)
Option for line differential protection I x 40 =
charging-current compensation
87 Stub-fault differential protection (for x 35 =
STUB breaker-and-a-half scheme)
90V Automatic Voltage controller for two- x 150 =
winding transformer
90V Automatic Voltage controller for two- x 180 =
winding transformer with parallel
operation
Number of two-winding transformers 2x x 5 = 2x
with parallel operation (Note: only
together with the function "Automatic
Voltage controller for two-winding
transformer with parallel operation")
90V Automatic Voltage controller for three- x 200 =
winding transformer
90V Automatic Voltage controller for grid x 175 =
coupling transformer
FL Fault locator, single-sided FL-one x 25 =
FL Fault locator plus (from V7.9) FL plus x 45 =
PMU Synchrophasor measurement PMU x 40 =
AFD Arc-protection (only with plug-in module
ARC-CD-3FO)
Measured values, standard

Measured values, extended: Min, Max, x 3 =

Avg
SIPROTEC 5
Configuration
Jun 25, 2020 3:57 PM

Functional scope 7UT85 Transf. Prot (2 Wind.):

Always Add selected Result
ANSI Function Abbr. included Qty. x Value = Points Qty.
Basic PQ measurements: THD and
harmonics (from V8.01)
Switching statistic counters

Circuit-breaker wear monitoring Ix, I²t, 2P x 10 =

CFC (Standard, control)

CFC arithmetic x 40 =
Switching sequences function x 5 =
Inrush current detection

External trip initiation

Control

PoW Point-on-Wave Switching (from V7.9) PoW x 425 =

Fault recording of analog and binary
signals
Monitoring and supervision

Protection interface, serial

Circuit-breaker 4x x 3 = 4x
Disconnector/Grounding switch 4x x 3 = 4x
Transformer side 7UT85 2x x 70 = 2x
Frequency-tracking groups (from V7.8)

Temperature acquisition via

communication protocol
Cyber Security: Role-Based Access x 25 =
Control (from V7.8)
Sum: 0