Pacifica Owners Manual PDF
Pacifica Owners Manual PDF
Pacifica Owners Manual PDF
1 INTRODUCTION .............................................................3 1
2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2
3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 3
4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181 4
5 STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271 5
6 WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .349 6
7 MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 367 7
8 MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 8
9 IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .427 9
10 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 437 10
CONTENTS
m Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 m Vehicle Identification Number . . . . . . . . . . . . . . . 6
m How To Use This Manual . . . . . . . . . . . . . . . . . . 4 m Vehicle Modifications/Alterations . . . . . . . . . . . . 7
m Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6
VEHICLE MODIFICATIONS/ALTERATIONS
1
WARNING!
NOTE: If you try to remove the key before you place the
WARNING!
lever in PARK, the key may become trapped temporarily
in the ignition cylinder. If this occurs, rotate the key to the Never leave children alone in a vehicle. Leaving
right slightly, then remove the key as described. If a children in a vehicle unattended is dangerous for a 2
malfunction occurs, the system will trap the key in the number of reasons. A child or others could be seri-
ignition cylinder to warn you that this safety feature is ously or fatally injured. Don’t leave the keys in the
inoperable. The engine can be started and stopped but ignition. A child could operate power windows,
the key cannot be removed until you obtain service. other controls, or move the vehicle.
NOTE: The power window switches, radio, power
outlets, and removable console (if equipped), will remain
active for up to 45 seconds after the ignition switch has CAUTION!
been turned off. Opening a vehicle front door will cancel
this feature. An unlocked car is an invitation to thieves. Always
remove key from the ignition and lock all doors
when leaving the vehicle unattended.
STEERING WHEEL LOCK — IF EQUIPPED NOTE: If you turned the wheel to the right to engage
Your vehicle may be equipped with a passive steering the lock, you must turn the wheel slightly to the right to
wheel lock. This lock prevents steering the vehicle with- disengage it. If you turned the wheel to the left to engage
out the ignition key. If the steering wheel is moved no the lock, turn the wheel slightly to the left to disengage it.
more than 1/2 turn in either direction and the key is not
in the ignition switch, the steering wheel will lock.
Automatic Transaxle Ignition Interlock System NOTE: A key, which has not been programmed, is also
This system prevents the key from being removed unless considered an invalid key even if it is cut to fit the
the shift lever is in PARK. It also prevents shifting out of ignition lock cylinder for that vehicle.
PARK unless the key is in the ACC, or ON positions, and
During normal operation, after turning on the ignition
2
the brake pedal is depressed.
switch, the Vehicle Security Alarm Indicator Light will
SENTRY KEY — IF EQUIPPED turn on for three (3) seconds for a bulb check. If the light
The Sentry Key Immobilizer System prevents unautho- remains on after the bulb check, it indicates that there is
rized vehicle operation by disabling the engine. The a problem with the electronics. In addition, if the light
system does not need to be armed or activated. Operation begins to flash after the bulb check, it indicates that
is automatic, regardless of whether the vehicle is locked someone used an invalid key to start the engine. Either of
or unlocked. these conditions will result in the engine being shut off
after two (2) seconds.
The system uses ignition keys, which have an embedded
electronic chip (transponder), to prevent unauthorized If the Vehicle Security Alarm Indicator Light turns on
vehicle operation. Therefore, only keys that are pro- during normal vehicle operation (vehicle running for
grammed to the vehicle can be used to start and operate longer than 10 seconds), it indicates that there is a fault in
the vehicle. The system will shut the engine off in two (2) the electronics. Should this occur, have the vehicle ser-
seconds if someone uses an invalid key to start the viced as soon as possible.
engine.
NOTE: When having the Sentry Key Immobilizer 4. Insert a blank Sentry Key into the ignition switch and
System serviced, bring all vehicle keys with you to the turn the ignition switch ON within 60 seconds. After 10
dealer. seconds a single chime will sound. The Theft Alarm Light
Customer Key Programming
will stop flashing, turn on for 3 seconds; then turn off. 2
You can program new sentry keys to the system if you The new Sentry Key has been programmed. The Keyless
have two valid sentry keys by performing the following Entry Transmitter will also be programmed during this
procedure: procedure. Repeat this procedure to program up to a
total of 8 keys. If you do not have a programmed sentry
1. Cut the additional Sentry Key Transponder blank(s) to
key, contact your dealer for details.
match the ignition switch lock cylinder key code.
NOTE: If a programmed key is lost, see your dealer to
2. Insert the first valid key into the ignition switch and
have all remaining keys erased from the systems
turn the ignition switch ON for at least 3 seconds but no
memory. This will prevent the lost key from starting your
longer than 15 seconds. Turn the ignition switch OFF and
vehicle. The remaining keys must then be repro-
remove the first key.
grammed. All vehicle keys must be taken to the dealer at
3. Insert the second valid key and turn the ignition the time of service to be reprogrammed.
switch ON within 15 seconds. After ten seconds a chime
will sound and the Theft Alarm Light will begin to flash.
Turn the ignition switch OFF and remove the second key.
NOTE: If the SECURITY light stays on continuously If the alarm system is armed and the battery becomes
during vehicle operation, have the system checked by disconnected the system will remain armed when the
your dealer. battery is reconnected. The exterior lights will flash, the
To Disarm the System:
horn will sound, and the ignition will not start the 2
vehicle. If this occurs, disarm the system.
Use the Keyless Entry transmitter to unlock the door. If
something has triggered the system in your absence, the Tamper Alert
horn will sound three times when you unlock the doors If the horn sounds 3 times when you unlock a front door
and the security lamp will flash for 30 seconds. Check the using either a key or the Keyless Entry Transmitter, the
vehicle for tampering. alarm has been activated. Check the vehicle for tamper-
ing.
The Security system will also disarm, if the vehicle is
started with a programmed Sentry Key. If an unpro- Security System Manual Override
grammed Sentry Key is used to start a vehicle, the engine The system will not arm if you lock the doors using the
will run for 2 seconds and then the security alarm will be manual door lock plunger.
initiated. To exit alarming mode, press the transmitter
Unlock button, or start the vehicle with a programmed
Sentry Key.
Keyless Entry Transmitter 1. Perform this operation while standing outside the
vehicle.
To unlock the doors and liftgate:
Press and release the UNLOCK button on the transmitter 2. Press and hold the UNLOCK button on your key fob.
once to unlock the driver’s door, or twice to unlock all
3. Continue to hold the UNLOCK button, wait at least 4
doors and liftgate. When the UNLOCK button is pressed,
seconds, but no longer than 10 seconds, then press and
the illuminated entry will initiate and the parking lights
hold the LOCK button. Release both buttons at the same
will flash on twice.
time.
4. This will allow you to unlock all doors on the first • On electronic vehicle information center (EVIC)
press of the UNLOCK button. equipped vehicles refer to “Sound Horn On Lock?”
under “Use Factory Settings?” in the EVIC section of
5. To reactivate the feature, repeat this procedure.
this manual.
6. If the programming procedure was unsuccessful see
• On non EVIC – equipped vehicles perform the follow-
your authorized dealer for programming assistance.
ing steps:
To lock the doors and liftgate:
1. Perform this operation while standing outside the
Press and release the LOCK button on the transmitter to
vehicle.
lock all doors. If the ignition is OFF, when the doors are
locked, the parking lights will flash on once and the horn 2. Press and hold the LOCK button on your key fob.
will chirp once.
3. Continue to hold the LOCK button, wait at least 4
Sound Horn On Lock seconds, but no longer than 10 seconds, then press and
Press and release the LOCK button on the transmitter to hold the PANIC button. Release both buttons at the same
lock all doors. The turn signal lights will flash and the time.
horn will chip once to acknowledge the lock signal. If
4. To reactivate the feature, repeat this procedure.
desired, the “Sound Horn On Lock” feature can be
turned on or off by using the following procedure: 5. If the programming procedure was unsuccessful see
your authorized dealer for programming assistance.
General Information
This device complies with part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions: 2
• This device may not cause harmful interference.
• This device must accept any interference received, includ-
ing interference that may cause undesired operation.
NOTE: Changes or modifications not expressly ap-
proved by the party responsible for compliance could
void the user’s authority to operate the equipment.
Separating Transmitter Halves
2. Remove and replace the battery. Avoid touching the If your Remote Keyless Entry transmitter fails to operate
new battery with your fingers. Skin oils may cause from a normal distance, check for these two conditions.
battery deterioration. If you touch a battery, clean it with
1. A weak battery in the transmitter. The expected life of
rubbing alcohol.
the battery is a minimum of three years.
3. To reassemble the transmitter case, snap the two
2. Closeness to a radio transmitter such as a radio station
halves together. Make sure there is an even “gap” be-
tower, airport transmitter, and some mobile or CB radios.
tween the two halves. Test transmitter operation.
DOOR LOCKS If the lock knob is up when you shut the door, the door
will lock. Therefore, make sure the keys are not inside the
Manual Door Locks
vehicle before closing the door.
Lock the doors by pushing up on the lock knob on each
door trim panel.
WARNING!
Power Door Locks locks will not operate. This prevents you from acciden-
A power door lock switch is located on each front door tally locking your keys in the vehicle. Removing the key
trim panel. Use this switch to lock or unlock all doors and or closing the door will allow the locks to operate. A
liftgate. chime will sound if the key is in the ignition and a door 2
is open, as a reminder to remove the key.
Auto Door Locks — If Equipped
The doors will lock automatically on vehicles with power
door locks if all of the following conditions are met:
1. The Automatic Door Locks feature is enabled.
2. The transmission is in gear.
3. All doors are closed.
4. The throttle is pressed.
5. The vehicle speed is above 15 mph (24 km/h).
Power Door Lock Switch
6. The doors were not previously locked using the power
If you press the power door lock switch while the key is door lock switch or remote keyless entry transmitter.
in the ignition, and any front door is open, the power
If desired, the “Auto Door Locks?” feature can be turned 4. Within 15 seconds cycle the key from the LOCK
on or off by using the following procedure: position to the ON/RUN position a minimum of four
times; ending in the LOCK position (Do not start the
• On electronic vehicle information center (EVIC)
engine).
equipped vehicles refer to “Auto Door Locks?” under
“Use Factory Settings?” in the EVIC section of this 5. Within 30 seconds, press the driver’s door lock switch
manual. in the LOCK direction.
• On non EVIC - equipped vehicles perform the follow- 6. A single chime will be heard to indicate the feature has
ing steps: been disabled.
Auto Door Locks Programming 7. To reactivate this feature, repeat the above steps.
1. Enter your vehicle and close all doors. 8. If a chime is not heard, program mode was canceled
before the feature could be disabled. If necessary, repeat
2. Fasten your seat belt (Fastening the seat belt will
this procedure.
cancel any chiming that may confuse you during this
programming procedure). Auto Unlock On Exit — If Equipped
This feature unlocks all of the doors of the vehicle when
3. Place the key into the ignition.
any door is opened. This will occur only after the vehicle
has been driven (shifted out of Park with all doors
closed) and then shifted back into the Park position.
This feature will not operate if there is any manual 4. Within 15 seconds, cycle the key from the LOCK
operation of the power door locks (Lock or Unlock). If position to the ON/RUN position a minimum of four
desired, the “Auto Unlock On Exit?” feature can be times ending in the LOCK position (do not start the
turned on or off by using the following procedure: engine). 2
• On electronic vehicle information center (EVIC) 5. Within 30 seconds, press the driver’s door lock switch
equipped vehicles refer to “Auto Unlock On Exit?” in the UNLOCK direction.
under “Use Factory Settings?” in the EVIC section of
6. A single chime will sound to indicate the feature has
this manual.
been changed.
• On non EVIC - equipped vehicles perform the follow-
7. Repeat the above steps to alternate the availability of
ing steps:
this feature.
Auto Unlock On Exit Programming
8. If a chime is not heard, program mode was canceled
1. Enter your vehicle and close all doors. before the feature could be changed. If necessary repeat
this procedure.
2. Fasten your seat belt (fastening the seat belt will cancel
any chimes that may be confusing during this program- NOTE: Use the Auto Door Locks and Auto Unlock
ming procedure). features in accordance with local laws.
3. Insert the key into the ignition.
NOTE: For emergency exit with the system engaged, To Disengage the Child Protection Door Lock
move the door lock knob to the UNLOCK position, roll
1. Open the rear door.
down the window and open the door with the outside
door handle. 2. Insert the tip of the vehicle’s ignition key (or any 2
similar item) into the child lock control and slide it
WARNING! downward.
Avoid trapping anyone in the vehicle in a collision. 3. Repeat Steps 1 and 2 to disengage the Child Protection
Remember that the rear doors can only be opened Door Lock on the opposite rear door.
from the outside when the child protection locks are NOTE: After disengaging the child protection door lock
engaged. system, always test the door from the inside to make
certain it is in the desired position.
WINDOWS The window lock switch on the driver’s door allows you
to disable the window controls on the passenger doors.
Power Windows
When the lock switch is pressed the window controls on
The window controls on the driver’s door control all the
the passenger doors will not illuminate and the passen-
door windows. The switches will operate only when the
ger windows will be disabled.
ignition switch is in the ON or ACCESSORY position or
during accessory delay. Auto Down Feature
All the power window switches have an auto down
feature. Press the window switch to the second detent,
release, and the window will go down automatically.
To open the window part way, press the window switch
to the first detent and release it when you want the
window to stop.
The power window switches remain active for up to 45
seconds after the ignition switch has been turned off.
Opening either front door will cancel this feature.
The time is customer programmable through the Elec- NOTE: Any impact due to rough road conditions may
tronic Vehicle Information Center (EVIC). Refer to trigger the auto reverse function unexpectedly during
“Power Accessory Delay?” under “Personal Settings auto-closure. If this happens, pull the switch lightly to the
(Customer Programmable Features)” in Section 4 of this first detent and hold to close window manually. 2
manual for details.
WARNING!
Auto Up Feature with Anti–Pinch Protection
Lift the window switch to the second detent, release, and There is no anti-pinch protection when the window
the window will go up automatically. is almost closed. To avoid personal injury be sure to
To stop the window from going all the way up during the clear your arms, hands, fingers and all objects from
auto-up operation, push down on the switch briefly. the window path before closing.
1. Pull the window switch up to close window com- the rear windows open, open the front and rear windows
pletely and continue to hold the switch up for an together to minimize the buffeting. If the buffeting occurs
additional two seconds after the window is closed. with the sunroof open, adjust the sunroof opening to
minimize the buffeting.
2. Push the window switch down firmly to the second
detent to open the window completely and continue to LIFTGATE
hold the switch down for an additional two seconds after The liftgate can be unlocked using the remote keyless
the window is fully open. entry or by activating the power door lock switches
Wind Buffeting located on either interior front door trim panel.
Wind buffeting can be described as the perception of Once unlocked, the liftgate can be opened or closed. To
pressure on the ears or a helicopter type sound in the open the liftgate, pull the release handle while raising the
ears. Your vehicle may exhibit wind buffeting with the liftgate with one fluid motion.
windows down, or the sunroof (if equipped) in certain
open or partially open positions. This is a normal occur-
rence and can be minimized. If the buffeting occurs with
The power liftgate may also be opened by pressing the the liftgate is opening or closing. A beeping signal will
button located on the overhead console. sound two seconds before the liftgate starts to open or
close.
WARNING!
NOTE:
• If anything obstructs the power liftgate while it is
Power Liftgate Button closing or opening, the liftgate will automatically
reverse to the closed or open position, provided it
When the remote button is pressed the “Lamp Flash”
meets sufficient resistance.
feature is enabled the tail lights will flash to signal that
• There are also pinch sensors attached to the side of the (62° C). Be sure to remove any build-up of snow or ice
liftgate. Light pressure anywhere along these strips from the liftgate before pressing any of the power
will cause the liftgate to return to the open position. liftgate switches.
• The liftgate must be in the full open position in order • If the power liftgate encounters multiple obstructions
2
to power close. If the liftgate is not fully open, press within the same cycle, the system will automatically
the power button to fully open the liftgate and then stop and must be opened or closed manually.
you can press the power button to close.
WARNING!
• If the liftgate release switch is activated while the
power liftgate is closing, the liftgate will reverse to the • Driving with the liftgate open can allow poison-
full open position. ous exhaust gases into your vehicle. You and your
• The power liftgate switches will not operate if the passengers could be injured by these fumes. Keep
vehicle is in gear or the vehicle speed is above 0 mph the liftgate closed when you are operating the
(0 km/h). vehicle.
• The power liftgate will not operate in temperatures • If you are required to drive with the liftgate open,
below 212° F (224° C) or temperatures above 143° F make sure that all windows are closed, and the
climate control blower switch is set at high speed.
DO NOT use the recirculation mode.
Gas props support the liftgate in the open position. If your vehicle is equipped with the Occupant Classifi-
However, because the gas pressure drops with tempera- cation System (OCS) there will be a Passenger Airbag
ture, it may be necessary to assist the props when Disabled (PAD) Indicator Light located on the center of
opening the liftgate in cold weather. the instrument panel.
OCCUPANT RESTRAINTS
Some of the most important safety features in your
vehicle are the restraint systems. These include the front
and rear seat belts for the driver and all passengers, front
airbags for both the driver and front passenger, and if
equipped, left and right window bags for the driver and
passengers seated next to a window and a driver inflat-
able knee blocker. If you will be carrying children too
small for adult-size seat belts, your seat belts or the
LATCH feature (refer to the Child Restraint section in this
manual), can be used to hold infant and child restraint
systems. Passenger Airbag Light — If OCS Equipped
NOTE: The front airbags have a multi stage inflator Buckle up even though you are an excellent driver, even
design. This allows the airbag to have different rates of on short trips. Someone on the road may be a poor driver
inflation that are based on collision severity. and cause a collision that includes you. This can happen
Please pay close attention to the information in this
far away from home or on your own street. 2
section. It tells you how to use your restraint system Research has shown that seat belts save lives, and they
properly to keep you and your passengers as safe as can reduce the seriousness of injuries in a collision. Some
possible. of the worst injuries happen when people are thrown
from the vehicle. Seat belts reduce the possibility of
WARNING! ejection and the risk of injury caused by striking the
inside of the vehicle. Everyone in a motor vehicle should
In a collision, you and your passengers can suffer be belted at all times.
much greater injuries if you are not properly buckled
up. You can strike the interior of your vehicle or other Lap/Shoulder Belts
passengers, or you can be thrown out of the vehicle. All the seats in your vehicle are equipped with Lap/
Always be sure you and others in your vehicle are Shoulder Belts.
buckled up properly. The belt webbing retractor is designed to lock during
very sudden stops or collisions. This feature allows the
shoulder part of the belt to move freely with you under
6. To release the belt, push the red button on the buckle. Adjustable Upper Shoulder Belt Anchorage
The belt will automatically retract to its stowed position. In the front seats, the shoulder belt anchorage can be
If necessary, slide the latch plate down the webbing to adjusted upward or downward to help position the belt
allow the belt to retract fully. away from your neck. Press the button to release the
anchorage, and then move it up or down to the position
WARNING! that serves you best.
2. At about 6 to 12 inches (15 to 30 cm) above the latch 3. Slide the latch plate upward over the folded webbing.
plate, grasp and twist the belt webbing 180° to create a The folded webbing must enter the slot at the top of the
fold that begins immediately above the latch plate. latch plate.
Grasp and Twist Slide the latch plate upward over the folded webbing
4. Continue to slide the latch plate up until it clears the
folded webbing.
NOTE: The following steps must occur within the first 4. Turn the ignition switch to the OFF position. A single
60 seconds of the ignition switch being turned to the ON chime will sound to signify that you have successfully
or RUN position. DaimlerChrysler does not recommend completed the programming.
deactivating the Enhanced Warning System (BeltAlert).
The Enhanced Warning System (BeltAlert) can be reacti-
1. Turn the ignition switch to the OFF position, and vated by repeating this procedure.
buckle the driver’s seat belt.
NOTE: Although BeltAlert has been deactivated, the
2. Turn the ignition switch to the RUN position (engine Seat Belt Warning Light will continue to illuminate while
does not need to be running), and wait for the Seat Belt the driver’s seat belt remains unbuckled.
Warning Light to turn off.
Seat Belts and Pregnant Women
3. Within 60 seconds of turning the ignition switch to the We recommend that pregnant women use the seat belts
RUN position, unbuckle and then re-buckle the driver’s throughout their pregnancies. Keeping the mother safe is
seat belt at least three times within 10 seconds, ending the best way to keep the baby safe.
with the seat belt buckled.
Pregnant women should wear the lap part of the belt
NOTE: Watch for the Seat Belt Warning Light to turn on across the thighs and as snug across the hips as possible.
while unbuckling and off while re-buckling the seat belt. Keep the belt low so that it does not come across the
It may be necessary to retract the seat belt. abdomen. That way the strong bones of the hips will take
the force if there is a collision.
WARNING!
Front airbags, along with seat belts, and front seat belt
WARNING!
pretensioners, work with the instrument panel knee
• Do not put anything on or around the airbag covers blockers to provide improved protection for the driver
or attempt to manually open them. You may dam- and front passenger. Left and right window bags also
age the airbags and you could be injured because work with seat belts to improve occupant protection.
the airbags are not there to protect you. These
protective covers for the airbag cushions are de- The seat belts are designed to protect you in many types
signed to open only when the airbags are inflating. of collisions. The front airbags deploy in moderate to
• If your vehicle is equipped with left and right severe frontal collisions.
window bags, do not stack luggage or other cargo
up high enough to block the location of the side NOTE: If equipped with an Occupant Classification
curtain airbag. The area where the side curtain System (OCS), the passenger front airbag may not deploy
airbag is located should remain free from any
obstructions. even when the driver front airbag has determined the
seat is empty or is occupied by a child.
• If your vehicle is equipped with left and right
window bags, do not have any accessory items If your vehicle is so equipped, the window bag on the
installed which will alter the roof, including add-
ing a sunroof to your vehicle. Do not add roof racks crash side of the vehicle is triggered in moderate to
that require permanent attachments (bolts or severe side collisions. But even in collisions where the
screws) for installation on the vehicle roof. Do not airbags inflate, you need the seat belts to keep you in the
drill into the roof of the vehicle for any reason. right position for the airbags to protect you properly.
Here are some simple steps you can take to minimize 5. If a child from 1 to 12 years old must ride in the front
the risk of harm from a deploying airbag. passenger seat because the vehicle is crowded, move the
seat as far back as possible, and use the proper child
1. Children 12 years old and under should ride buckled
up in the rear seat.
restraint (refer to information on Child Restraint in this 2
section).
2. Infants in rear-facing child restraints should NEVER
6. You should read the instructions provided with your
ride in the front seat of a vehicle with a passenger front
child restraint to make sure that you are using it properly.
airbag. An airbag deployment could cause severe injury
or death to infants in that position. 7. All occupants should use their seat belts properly.
3. Children that are not big enough to wear the vehicle 8. The driver and front passenger seats should be moved
seat belt properly (refer to information on Child Restraint back as far as practical to allow the airbags time to inflate.
in this section) should be secured in the rear seat in child
9. If your vehicle has side curtain airbags do not lean
restraints or belt-positioning booster seats.
against the door, airbags will inflate forcefully into the
4. Older children who do not use child restraints or space between you and the door.
belt-positioning booster seats should ride properly buck-
10. If the airbag system in this vehicle needs to be
led up in the rear seat. Never allow children to slide the
modified to accommodate a disabled person, contact the
shoulder belt behind them or under their arm.
Customer Center. Phone numbers are provided in the 9If
You Need Customer Assistance9 section in this manual.
• Knee Impact Bolster proper rate of inflation. The front airbag inflators are
designed to provide different rates of airbag inflation.
• Front Seat Belt Pretensioners
• The ORC will not detect side, roll over, or rear impacts.
• Front Passenger Seat Occupant Classification System 2
(OCS) — If OCS Equipped • The ORC monitors the readiness of the electronic parts
of the system whenever the ignition switch is in the
− Occupant Classification Module
START or RUN positions. These include all of the
− Passenger Airbag Disabled (PAD) Indicator Light items listed above except the steering wheel and
column, instrument panel and passenger knee bol-
− Interconnecting Wiring
sters. If the key is in the OFF position, in the ACC
− Bladder Assembly position, or not in the ignition, the airbags are not on
and will not inflate.
− Belt Tension Sensor
• Also, the ORC turns on the AIRBAG warn-
How The Airbag System Works ing light and PAD indicator light in the
center of the instrument panel for 6 to 8
• The Occupant Restraint Controller (ORC) determines
seconds for a self-check when the ignition is
if a frontal collision is severe enough to require the
first turned on. After the self-check, the AIRBAG
airbags to inflate. Based on the level of collision
warning light will turn off. If equipped, the PAD
severity, the front control module determines the
indicator light will function normally. If the ORC
detects a malfunction in any part of the system, it turns nontoxic gas is generated to inflate the front airbags.
on the AIRBAG warning light either momentarily or Different airbag inflation rates may be possible based
continuously. A single chime will sound if the light on collision severity. The steering wheel hub trim
comes on again after initial start up. cover and the upper right side of the instrument panel
separate and fold out of the way as the airbags inflate
WARNING! to their full size. The airbags fully inflate in about
50–70 milliseconds. This is about half of the time it
Ignoring the AIRBAG warning light in your instru- takes to blink your eyes. The airbags then quickly
ment panel could mean you won’t have the airbags to deflate while helping to restrain the driver and front
protect you in a collision. If the light does not come passenger.
on, stays on after you start the vehicle, or if it comes
on as you drive, have the airbag system checked right The driver’s and passenger’s front airbag gas is vented
away. through the airbag material towards the instrument
panel. In this way the airbags do not interfere with
your control of the vehicle.
• The Driver and Passenger Airbag/Inflator Units are • The Side Airbag Inflatable Curtains are designed to
located in the center of the steering wheel and the right activate only in certain side collisions. When the ORC
side of the instrument panel. When the ORC and and the side impact sensors (with side impact option)
impact sensors detects a collision requiring the air- detects a collision requiring the window bags to
bags, it signals the inflator units. A large quantity of
inflate, it signals the inflators on the crash side of the protect the knees and position you for the best inter-
vehicle. A quantity of nontoxic gas is generated to action with the front airbag. The Driver Inflatable
inflate the window bag. The inflating window bag Knee Blocker fully inflates in about 50 milliseconds,
pushes the outside edge of the headliner out of the this is only about half of the time it takes you to blink 2
way and covers the window. The airbag inflates in your eyes. It then quickly deflates while helping to
about 30 milliseconds (about one quarter of the time it protect the driver’s knees.
takes to blink your eyes) with enough force to injure
• The Knee Impact Bolsters help protect the knees, and
you if you are not belted and seated properly, or if
position everyone for the best interaction with the
items are positioned in the area where the window bag
front airbag.
inflates. This especially applies to children. The win-
dow bag is only about 31⁄2 inches (9 cm) thick when it • If your vehicle contains a Passenger Airbag Disable
is inflated. indicator light, it will be equipped with the Occupant
Classification System (OCS). The OCS system will
• When the ORC and the impact sensors detect a
classify an occupant into a size category based on
collision requiring the Driver Inflatable Knee Blocker
sensor readings from within the seat cushion. Occu-
— If Equipped, signals the inflator unit. A quantity of
pants should try to remain in a normally seated
nontoxic gas is generated to inflate the Driver Inflat-
position. If the occupant’s weight is transferred to
able Knee Blocker. The Driver Inflatable Knee Blocker
inflates rearward towards the driver’s knees to help
another object in the vehicle (i.e. feet on the dash- If there is a fault present in the system, the AIRBAG
board), the OCS may not be able to properly approxi- warning light will illuminate indicating that you should
mate occupant size. Furthermore, the occupant size take the vehicle to an authorized dealer. In the presence
may appear to increase or decrease due to objects of an occupant in the passenger seat, if both the PAD
hanging on the seat, other passengers pushing on the indicator light and AIRBAG warning light are illumi-
seat, or objects lodged underneath the seat. nated the airbag will be disabled.
If there is a rapid change in temperature or humidity, The ORC will not allow front airbag deployment in the
the OCS may not be able to properly approximate event of a collision for occupants classified into the
occupant size. If your seat including your trim cover empty or child size categories. The PAD indicator light
and cushion needs to be serviced in any way (includ- will illuminate indicating that the Passenger Airbag is
ing removal or loosening/tightening of seat attach- OFF when the OCS has determined that the occupant size
ment bolts), take the vehicle to your authorized dealer. category is a child. Also, when the seat is empty or an
Only manufacturer approved seat accessories may be object that weighs less than a predetermined threshold is
used. placed on the seat, the light will remain OFF. (The PAD
indicator light is an amber light located on the center of
the instrument panel above the climate controls.)
front passenger airbag is allowed. If a fault is present, the resultant bladder pressure increase due to applied
the AIRBAG warning light is illuminated. lap belt tension does not cause a small occupant to be
classified as a larger occupant.
• The Passenger Airbag Disabled (PAD) Indicator
Light — If Equipped indicates to the driver and • The Bladder Assembly — If Equipped is located
passenger when the airbag is turned OFF in the beneath the seat cushion foam. The pressure sensor
presence of a properly seated occupant. When the PAD sends a signal to the OCM.
indicator light is illuminated, the airbag is OFF. Also,
The front passenger seat assembly contains critical com-
when the Occupant Classification System (OCS) de-
ponents that affect the front passenger airbag deploy-
tects either an empty seat of a weight less than the
ment. Correctly functioning front passenger seat compo-
predetermined occupant threshold, the ORC will not
nents are critical for the Occupant Classification System
illuminate the PAD indicator light even though the
(OCS) to properly classify the front passenger and calcu-
airbag is turned off. When the OCS detects an adult
late the proper airbag deployment. Do not make any
the PAD indicator light will be off, and the airbag will
modifications to the front passenger seat components,
be enabled.
assembly, or to the seat cover.
• The Belt Tension Sensor (BTS) — If Equipped is
located at the outboard passenger lap belt anchor. The
BTS generates a signal based on outboard lap belt
tension. This signal is sent to the OCM to ensure that
In the event that an investigation is undertaken by 1. Used for research purposes, such as to match data
DaimlerChrysler Corporation (regardless of initiative), with a particular crash record in an aggregate database,
the company or its designated representative will first provided confidentiality of personal data is thereafter
obtain permission of the appropriate custodial entity for preserved
the vehicle (usually the vehicle owner or lessee) before
2. Used in defense of litigation involving a
accessing the electronic data stored, unless ordered to
DaimlerChrysler Corporation product
download data by a court with legal jurisdiction (i.e.,
pursuant to a warrant). A copy of the data will be 3. Requested by police under a legal warrant
provided to the custodial entity upon request. General
4. Otherwise required by law
data that does not identify particular vehicles or crashes
may be released for incorporation in aggregate crash Data Parameters that May Be Recorded:
databases, such as those maintained by the US govern-
• Diagnostic trouble code(s) and warning light status for
ment and various states. Data of a potentially sensitive
electronically-controlled safety systems, including the
nature, such as would identify a particular driver, ve-
airbag system
hicle, or crash, will be treated confidentially. Confidential
data will not be disclosed by DaimlerChrysler Corpora- • Airbag disable light status (if equipped)
tion to any third party except when:
• 9Time9 of airbag deployment (in terms of ignition
cycles and vehicle mileage)
Older Children and Child Restraints Children Too Large For Booster Seats
Children who weigh more than 20 lbs (9 kg) and who are Children who are large enough to wear the shoulder belt
older than one year can ride forward-facing in the comfortably, and whose legs are long enough to bend
vehicle. Forward-facing child seats and convertible child over the front of the seat when their back is against the 2
seats used in the forward-facing direction are for children seatback, should use the lap/shoulder belt in a rear seat.
who weigh 20 to 40 lbs (9 to 18 kg) and who are older
• Make sure that the child is upright in the seat.
than one year. These child seats are also held in the
vehicle by the lap/shoulder belt or the LATCH child • The lap portion should be low on the hips and as snug
restraint anchorage system. Refer to “Lower Anchors and as possible.
Tether for CHildren (LATCH)” later in this section.
• Check belt fit periodically. A child’s squirming or
The belt-positioning booster seat is for children weighing slouching can move the belt out of position.
more than 40 lbs (18 kg), but who are still too small to fit
• If the shoulder belt contacts the face or neck, move the
the vehicle’s seat belts properly. If the child cannot sit
child closer to the center of the vehicle. If this doesn’t
with knees bent over the vehicle’s cushion while the
help, move the child to the center rear seating position
child’s back is against the seatback, then the child should
and use the lap belt. Never allow a child to put the
use a Belt Positioning Booster Seat. The child and booster
shoulder belt under an arm or behind their back.
seat are held in the vehicle by the lap/shoulder belt.
(Some booster seats are equipped with a front shield and NOTE: For additional information, refer to
are held in the vehicle by the lap portion.) www.seatcheck.org or call 1-866-SEATCHECK.
• In the rear seat, you may have trouble tightening the • When your child restraint is not in use, secure it in the
lap/shoulder belt on the child restraint because the vehicle with the seat belt or remove it from the vehicle.
buckle or latch plate is too close to the belt path Don’t leave it loose in the vehicle. In a sudden stop or
opening on the restraint. Disconnect the latch plate collision, it could strike the occupants or seatbacks and 2
from the buckle and twist the short buckle end of the cause serious personal injury.
belt several times to shorten it. Insert the latch plate
Lower Anchors and Tether for CHildren (LATCH)
into the buckle with the release button facing out.
Each vehicle is equipped with two child restraint anchor-
• If the belt still can’t be tightened, or if pulling and age systems called LATCH, which stands for Lower
pushing on the restraint loosens the belt, disconnect Anchors and Tether for CHildren. The LATCH child
the latch plate from the buckle, turn the buckle restraint anchorage systems are installed on second-row
around, and insert the latch plate into the buckle seats only. LATCH child restraint anchorage systems are
again. If you still can’t make the child restraint secure, not provided on the six passenger third row seats.
try a different seating position.
• Buckle the child into the seat according to the child
restraint manufacturer’s directions.
LATCH ANCHORS
Five passenger vehicles are equipped with a second row
bench seat only. The two outboard seating positions have
lower anchorages that can accommodate rigid mount or
flexible webbing-mounted LATCH-compatible child
seats. The center seating position of the bench seat can
strap. Forward-facing toddler restraints and some Because the lower anchorages are to be introduced to
rearward-facing infant restraints will also be equipped passenger carrying vehicles over a period of years, child
with a tether strap, a hook and means for adjusting the restraint systems having attachments for those anchor-
tension in the strap. ages will continue to have features for installation in
vehicles using the lap or lap/shoulder belt. They will also
In general, you will first loosen the adjusters on the lower
have tether straps, and you are urged to take advantage
straps and tether straps so that you can more easily attach
of all of the available attachments provided with your
the hook or connector to the lower anchorages and tether
child restraint in any vehicle.
anchorages. Then tighten all three straps as you push the
child restraint rearward and downward into the seat. NOTE: When using the LATCH attaching system to
install a child restraint, please ensure that all seat belts
Child restraint systems having attachments designed to
not being used for occupant restraints are stowed and out
connect to the lower anchorages are now available. Child
of reach of children. It is recommended that before
restraints having tether straps and hooks for connection
installing the child restraint, buckle the seat belt so the
to the seatback tether anchorage have been available for
seat belt is tucked behind the child restraint and out of
some time. In fact, many child restraint manufacturer’s
reach. If the buckled seat belt interferes with the child
will provide add-on tether strap kits for some of their
restraint installation, instead of tucking the seat belt
older products.
behind the child restraint, route the seat belt through the
child restraint belt path and then buckle it. This should
stow the seat belt out of the reach of an inquisitive child.
Remind all children in the vehicle that the seat belts are Transporting Pets
not toys and should not be played with, and never leave Airbags deploying in the front seat could harm your pet.
your child unattended in the vehicle. An unrestrained pet could be thrown about and possibly
Not all child restraint systems will be installed as we
injured, or injure a passenger during panic braking or in 2
a collision.
have described here. Again, carefully follow the instruc-
tions that come with the child restraint system. Pets should be restrained in the rear seat in pet harnesses
or pet carriers that are secured by seat belts.
WARNING!
ENGINE BREAK-IN RECOMMENDATIONS
Improper installation of a child restraint to the A long break-in period is not required for the engine in
LATCH anchorages can lead to failure of an infant or your new vehicle.
child restraint. The child could be badly injured or Drive moderately during the first 300 miles (500 km).
killed. Follow the manufacturer’s directions exactly After the initial 60 miles (100 km), speeds up to 50 or 55
when installing an infant or child restraint. mph (80 or 90 km/h) are desirable.
While cruising, brief full-throttle acceleration, within the
limits of local traffic laws, contributes to a good break-in.
Wide open throttle acceleration in low gear can be
detrimental and should be avoided.
The engine oil installed in the engine at the factory is a SAFETY TIPS
high quality energy conserving type lubricant. Oil
Exhaust Gas
changes should be consistent with anticipated climate
conditions under which vehicle operations will occur.
WARNING!
The recommended viscosity and quality grades are
shown in Section 7 of this manual. NON-DETERGENT Exhaust gases can injure or kill. They contain carbon
OR STRAIGHT MINERAL OILS MUST NEVER BE monoxide (CO) which is colorless and odorless.
USED. Breathing it can make you unconscious and can
A new engine may consume some oil during its first few eventually poison you. To avoid breathing (CO)
thousand miles (kilometers) of operation. This should be follow the safety tips below.
considered as a normal part of the break-in and not
interpreted as an indication of difficulty.
Do not run the engine in a closed garage or in confined
areas any longer than needed to move your vehicle in or
out of the area.
If it is necessary to sit in a parked vehicle with the engine
running, adjust your heating or cooling controls to force
outside air into the vehicle. Set the blower at high speed.
CONTENTS
3
m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86 ▫ Heated Remote Control Mirrors —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .89
▫ Inside Day / Night Mirror . . . . . . . . . . . . . . . .86
▫ Illuminated Vanity Mirrors . . . . . . . . . . . . . . . .89
▫ Automatic Dimming Mirror — If Equipped . . . .86
m Hands–Free Communication (UConnect™) —
▫ Driver’s Side Outside Mirror Auto Dimmer —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . .87
▫ Operations . . . . . . . . . . . . . . . . . . . . . . . . . . .91
▫ Exterior Mirrors Folding Feature . . . . . . . . . . .87
▫ Phone Call Features . . . . . . . . . . . . . . . . . . . .98
▫ Outside Mirror — Driver’s Side . . . . . . . . . . . .87
▫ UConnect™ System Features . . . . . . . . . . . . . 100
▫ Outside Mirror — Passenger’s Side . . . . . . . . . .88
▫ Advanced Phone Connectivity . . . . . . . . . . . . 105
▫ Power Remote-Control Mirrors . . . . . . . . . . . . .88
▫ Things You Should Know About Your ▫ Second Row Bench Seating —
UConnect™ System . . . . . . . . . . . . . . . . . . . . 106 If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 122
▫ General Information . . . . . . . . . . . . . . . . . . . 114 ▫ Second Row Fold & Tumble Seats —
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 123
m Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
▫ Third Row Easy Exit — If Equipped . . . . . . . . 124
▫ 10–Way Driver’s Power Seat — If Equipped . . 115
▫ Third Row Seating — If Equipped . . . . . . . . . 126
▫ 8–Way Driver’s Power Seat — If Equipped . . . 116
▫ Load Floor — If Equipped . . . . . . . . . . . . . . . 127
▫ 4–Way Passenger’s Power Seat . . . . . . . . . . . . 116
▫ Plastic Grocery Bag Retainer . . . . . . . . . . . . . 128
▫ Adjustable Head Restraints . . . . . . . . . . . . . . 117
m Driver Memory Seat — If Equipped . . . . . . . . . 129
▫ Heated Seats — If Equipped . . . . . . . . . . . . . 118
▫ Easy Exit Seat (Available With Memory Seat
▫ Second Row Manual Seat Recliner —
Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 120
▫ Tilt Mirrors In Reverse (Available With
▫ Second Row Manual Seat Adjuster —
Memory Seat Only) — If Equipped . . . . . . . . . 133
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 121
m To Open And Close The Hood . . . . . . . . . . . . . 133
▫ To Vary The Speed Setting . . . . . . . . . . . . . . . 145 ▫ Traction Control System (TCS) . . . . . . . . . . . . 154
▫ To Accelerate For Passing . . . . . . . . . . . . . . . 146 ▫ Brake Assist System (BAS) . . . . . . . . . . . . . . . 154
m Garage Door Opener — If Equipped . . . . . . . . . 146 ▫ ESP (Electronic Stability Program) . . . . . . . . . 155
▫ Programming HomeLinkt . . . . . . . . . . . . . . . 147 m Adjustable Pedals — If Equipped . . . . . . . . . . . 159
▫ Canadian Programming/Gate Programming . . 150 m Rear Park Sense System — If Equipped . . . . . . . 160
▫ Using HomeLinkt . . . . . . . . . . . . . . . . . . . . . 151 ▫ Rear Park Assist Sensors . . . . . . . . . . . . . . . . 161
▫ Reprogramming a Single HomeLinkt ▫ Rear Park Assist Warning Display . . . . . . . . . 162
Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151
▫ Enable/Disable The Rear Park Assist System —
▫ Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 165
▫ Troubleshooting Tips . . . . . . . . . . . . . . . . . . . 152 ▫ Service The Rear Park Assist System . . . . . . . . 165
▫ General Information . . . . . . . . . . . . . . . . . . . 152 ▫ Cleaning The Rear Park Assist System . . . . . . 166
m Anti-Lock Brake System (ABS) . . . . . . . . . . . . . 153 m Rear Camera — If Equipped . . . . . . . . . . . . . . . 166
m Electronic Brake Control System - m Overhead Console — If Equipped . . . . . . . . . . . 168
ABS/TCS/BAS/ESP . . . . . . . . . . . . . . . . . . . . . 154
WARNING!
Press the rocker switch to the L or R for Left or Right Sun Visor Extension
mirror selection. Use the center off position to guard The sun visors may be pulled out to provide extended
against accidentally moving a mirror position. coverage of the side glass.
Select a mirror and press one of the four arrows for the HANDS–FREE COMMUNICATION (UConnect™) —
direction you want the mirror to move. IF EQUIPPED 3
Power mirror preselected positions can be controlled by UConnect™ is a voice-activated, hands-free, in- vehicle
the optional Driver Memory Seat Feature. Refer to communications system. UConnect™ allows you to dial
“Driver Memory Seat” in section 3 of this manual. a phone number with your cellular phone using simple
voice commands (e.g., 9Call” { “Mike” {”Work9 or 9Dial”
Heated Remote Control Mirrors — If Equipped { “248-555-12129). Your cellular phone’s audio is trans-
These mirrors are heated to melt frost or ice. This feature mitted through your vehicle’s audio system; the system
is activated whenever you turn on the Rear Window will automatically mute your radio when using the
Defrost. UConnect™ system.
Illuminated Vanity Mirrors NOTE: The UConnect™ system use requires a cellular
An illuminated vanity mirror is on the sun visor. To use phone equipped with the Bluetooth 9Hands-Free Profile,9
the mirror, rotate the sun visor down and swing the version 0.96 or higher. See www.chrysler.com/uconnect
mirror cover upward. The lights turn on automatically. for supported phones.
Closing the mirror cover turns off the lights.
UConnect™ allows you to transfer calls between the with the system at a time. The system is available in
system and your cellular phone as you enter or exit your English, Spanish, or French languages (as equipped).
vehicle, and enables you to mute the system’s micro-
phone for private conversation.
The UConnect™ phonebook enables you to store up to 32
names and four numbers per name. Each language has a
separate 32-name phonebook accessible only in that
language. This system is driven through your Blue-
tooth™ Hands-Free profile cellular phone. UConnect™
features Bluetooth™ technology - the global standard
that enables different electronic devices to connect to
each other without wires or a docking station, so UCon-
nect works no matter where you stow your cellular
phone (be it your purse, pocket, or briefcase), as long as
UConnect™ Switches
your phone is turned on and has been paired to the
vehicle’s UConnect™ system. The UConnect™ system The rearview mirror contains the microphone for the
allows up to seven cellular phones to be linked to system. system and the radio has the two control buttons that will
Only one linked (or paired) cellular phone can be used
example, you can use the combined form voice com- Cancel Command
mand 9Phonebook New Entry,9 or you can break the At any prompt, after the voice on beep, you can say
combined form command into two voice commands: 9Cancel9 and you will be returned to the main menu.
9Phonebook9 and 9New Entry.9 Please remember, the However, in a few instances the system will take you
UConnect™ system works best when you talk in a back to the previous menu.
normal conversational tone, as if speaking to some one
Pair (Link) UConnect™ System to a Cellular Phone
sitting eight feet away from you.
To begin using your UConnect™ system, you must pair
Voice Command Tree your compatible Bluetooth™ enabled cellular phone.
Refer to “Voice Tree” at the end of this section.
To complete the pairing process, you will need to refer-
Help Command ence your cellular phone owner’s manual. One of the
If you need assistance at any prompt, or if you want to following vehicle specific websites may also provide
know your options are at any prompt, say 9Help9 follow- detailed instructions for pairing with the brand of phone
ing the voice on beep. The UConnect™ system will play that you have:
all the options at any prompt if you ask for help.
NOTE:
To activate the UConnect™ system from idle, simply • www.chrysler.com/uconnect
press the ’Phone’ button and follow audible prompts for
• www.dodge.com/uconnect
directions. All UConnect™ system sessions begin with a
press of the ’Phone’ button on the radio control head. • www.jeep.com/uconnect
The following are general phone to UConnect™ System • You will then be asked to give your cellular phone a
pairing instructions: priority level between 1 and 7, 1 being the highest
priority. You can pair up to seven cellular phones to
• Press the ’Phone’ button to begin.
your UConnect™ system. However, at any given time,
• After the 9Ready9 prompt and the following beep, say only one cellular phone can be in use, connected to
9Setup Phone Pairing9 and follow the audible prompts. your UConnect™ System. The priority allows the 3
UConnect™ system to know which cellular phone to
• When prompted, after the voice on beep, say 9Pair a
use if multiple cellular phones are in the vehicle at the
Phone9 and follow the audible prompts.
same time. For example, if priority 3 and priority 5
• You will be asked to say a four-digit pin number, phones are present in the vehicle, the UConnect™
which you will later need to enter into your cellular. system will use the priority 3 cellular phone when you
You can enter any four-digit pin number. You will not make a call. You can select to use a lower priority
need to remember this pin number after the initial cellular phone at any time (refer to 9Advanced Phone
pairing process. Connectivity9).
• For identification purposes, you will be prompted to Call/Dial by Saying a Number
give the UConnect™ system a name for your cellular
• Press the ’Phone’ button to begin.
phone. Each cellular phone that is paired should be
given a unique phone name. • After the 9Ready9 prompt and the following beep, say
9Dial.9
• System will prompt you to say the number you want • System will prompt you to say the name of the person
call. you want call.
• For example, you can say 9234-567-8901.9 The phone • After the 9Ready9 prompt and the following beep, say
number that you enter must be of valid length and the name of the person you want to call. For example,
combination. Based on the country in which the ve- you can say 9John Doe,9 where John Doe is a previ-
hicle was purchased, the UConnect™ limits the user ously stored name entry in the UConnect™ phone-
from dialing invalid combination of numbers. For book. Refer to 9Add Names to Your UConnect™
example, in USA, 234-567-890 is nine digits long, Phonebook,9 to learn how to store a name in the
which is not a valid USA phone number - the closest phonebook.
valid phone number has ten digits.
• The UConnect™ system will confirm the name and
• The UConnect™ system will confirm the phone num- then dial the corresponding phone number, which
ber and then dial. The number will appear in the may appear in the display of certain radios.
display of certain radios.
Add Names to Your UConnect™ Phonebook
Call by Saying a Name
NOTE: Adding names to phonebook is recommended
• Press the “Phone” button to begin. when vehicle is not in motion.
• After the 9Ready9 prompt and the following beep, say • Press the “Phone” button to begin.
“Dial” or Call.9
• After the 9Ready9 prompt and the following beep, say The UConnect™ system will allow you to enter up to 32
9Phonebook New Entry.9 names in the phonebook with each name having up to
four associated phone numbers and designations. Each
• When prompted, say the name of the new entry. Use of
language has a separate 32-name phonebook accessible
long names helps the voice recognition and is recom-
only in that language.
mended. For example, say 9Robert Smith9 or 9Robert9
instead of 9Bob.9 Edit Entries in the UConnect™ Phonebook
3
• When prompted, enter the number designation (e.g., NOTE: Editing phonebook entries is recommended
9Home,9 9Work,9 9Mobile,9 or 9Pager9). This will allow when vehicle is not in motion.
you to store multiple numbers for each phonebook
• Press the ’Phone’ button to begin.
entry, if desired.
• After the 9Ready9 prompt and the following beep, say
• When prompted, recite the phone number for the
9Phonebook Edit.9
phonebook entry that you are adding.
• You will then be asked for the name of the phonebook
After you are finished adding an entry into the phone-
entry that you wish to edit.
book, you will be given the opportunity to add more
phone numbers to the current entry or to return to the • Next, choose the number designation (home, work,
main menu. mobile, or pager) that you wish to edit.
• When prompted, recite the new phone number for the • After the 9Ready9 prompt and the following beep, say
phonebook entry that you are editing. 9Phonebook Delete.9
After you are finished editing an entry in the phonebook, • After you enter the Phonebook Delete menu, you will
you will be given the opportunities to edit another entry then be asked for the name of the entry that you wish
in the phonebook, call the number you just edited, or to delete. You can either say the name of a phonebook
return to the main menu. entry that you wish to delete or you can say 9List
Names9 to hear a list of the entries in the phonebook
9Phonebook Edit9 can be used to add another phone
from which you choose. To select one of the entries
number to a name entry that already exists in the
from the list, press the 9Voice Recognition9 button
phonebook. For example, the entry John Doe may have a
while the UConnect™ system is playing the desired
mobile and a home number, but you can add John Doe’s
entry and say 9Delete.9
work number later using the 9Phonebook Edit9 feature.
• After you enter the name, the UConnect™ system will
Delete Entries in the UConnect™ Phonebook
ask you which designation you wish to delete, home,
NOTE: Editing phonebook entries is recommended work, mobile, or pager. Say the designation you wish
when vehicle is not in motion. to delete.
• Press the ’Phone’ button to begin. NOTE: Note that only the phonebook entry in the
current language is deleted.
After confirmation, the phonebook entries will be de- List All Names in the UConnect™ Phonebook
leted. Note that only the phonebook in the current
• Press the ’Phone’ button to begin.
language is deleted.
• After the 9Ready9 prompt and the following beep, say
Delete All Entries in the UConnect™ Phonebook
9Phonebook List Names.9
• Press the ’Phone’ button to begin.
• The UConnect™ system will play the names of all the
3
• After the 9Ready9 prompt and the following beep, say phonebook entries.
9Phonebook Erase All.9
• To call one of the names in the list, press the 9Voice
• The UConnect™ system will ask you to verify that you Recognition’ button during the playing of the desired
wish to delete all the entries from the phonebook. name, and then say 9Call.
• After confirmation, the phonebook entries will be NOTE: The user can also exercise 9Edit9 or 9Delete9
deleted. operations at this point.
• Note that only the phone book in the current language • The UConnect™ system will then prompt you as to
is deleted. number designation you wish to call.
• The selected number will be dialed.
second call is in progress. To go back to the first call, refer Conference Call
to 9Toggling Between Calls.9 To combine two calls, refer When two calls are in progress (one active and one on
to 9Conference Call.9 hold), press and hold the ’Phone’ button until you hear a
double beep indicating that the two calls have been
Place/Retrieve a Call from Hold
joined into one conference call.
To put a call on hold, press the 8Phone’ button until you
hear a single beep. This indicates that the call is on hold. Three-Way Calling
3
To bring the call back from hold, press and hold the To initiate three-way calling, press the ’Voice Recogni-
8Phone’ button until you hear a single beep. tion’ button while a call is in progress and make a second
phone call as described under 9Making a Second Call
Toggling Between Calls
while Current Call in Progress.9 After the second call has
If two calls are in progress (one active and one on hold),
established, press and hold the ’Phone’ button until you
press the ’Phone’ button until you hear a single beep
hear a double beep indicating that the two calls have
indicating that the active and hold status of the two calls
been joined into one conference call.
have switched. Only one call can be placed on hold at one
time. Call Termination
To end a call in progress, momentarily press the 8Phone’
button. Only the active call(s) will be terminated and if
there is a call on hold, it will become the new active call.
• After the 9Ready9 prompt and the following beep, say If the phone is not reachable and the UConnect™ system
the name of the language you wish to switch to is operational, you may reach the emergency number as
(English, Espanol, or Francais, if so equipped). follows:
• Continue to follow the system prompts to complete • Press the ’Phone’ button to begin.
language selection.
• After the 9Ready9 prompt and the following beep, say 3
After selecting one of the languages, all prompts and 9Emergency9 and the UConnect™ system will instruct
voice commands will be in that language. the paired cellular phone to call the emergency num-
ber. This feature is only supported in the USA.
NOTE: After every UConnect™ language change op-
eration, only the language specific 32-name phonebook is NOTE: The emergency number dialed is based on the
usable. The paired phone name is not language specific Country where the vehicle is purchased (911 for USA and
and usable across all languages. Canada and 060 for Mexico). The number dialed may not
be applicable with the available cellular service and area.
Emergency Assistance
If you are in an emergency and the mobile phone is The UConnect™ system does slightly lower your chances
reachable: of successfully making a phone call as to that for the cell
phone directly.
• Pick up the phone and manually dial the emergency
number for your area. Your phone must be turned on and paired to the UCon-
nect™ system to allow use of this vehicle feature in
When calling a number with your UConnect™ system Turning Confirmation Prompts On/Off
that normally requires you to enter in a touch-tone Turning confirmation prompts off will stop the system
sequence on your cellular phone keypad, you can push from confirming your choices (e.g., the UConnect™
the ’Voice Recognition’ button and say the sequence you system will not repeat a phone number before you dial
wish to enter followed by the word 9Send.9 For example, it).
if required to enter your pin number followed with a
• Press the ’Phone’ button to begin.
3
pound 3 7 4 6 #, you can press the ’Voice Recognition’
button and say 93 7 4 6 # Send.9 Saying a number, or • After the 9Ready9 prompt and the following beep, say
sequence of numbers, followed by 9Send9 is also to be 9Setup Confirmations.9 The UConnect™ system will
used to navigate through an automated customer service play the current confirmation prompt status and you
center menu structure and to leave a number on a pager. will be given the choice to change it.
Barge In - Overriding Prompts Phone and Network Status Indicators
The ’Voice Recognition’ button can be used when you If available on the radio and/or on a premium display
wish to skip part of a prompt and issue your voice such as the instrument panel cluster, and supported by
recognition command immediately. For example, if a your cell phone, the UConnect™ system will provide
prompt is playing 9Would you like to pair a phone, clear notification to inform you of your phone and network
a{,9 you could press the ’Voice Recognition’ button and status when you are attempting to make a phone call
say 9Pair a Phone9 to select that option without having to using UConnect™. The status is given for roaming net-
listen to the rest of the voice prompt. work signal strength, phone battery strength, etc.
NOTE: Certain brands of mobile phones do not send the In order to un-mute the UConnect™ system:
dial ring to the UConnect™ system to play it on the • Press the ’Voice Recognition’ button.
vehicle audio system, so you will not hear it. Under this
situation, after successfully dialing a number, the user • After the 9Ready9 prompt and the following beep, say
may feel that the call did not go through even though the 9Mute-off.9
call is in progress. Once your call is answered, you will Information Service
hear the audio. When using AT&T Wireless Service, dialing to phone
number 9#121,9 you can access voice activated automated
system to receive news, weather, stocks, traffic, etc.
related information. This is an AT&T provided service.
• Press the ’Phone’ button to begin. • At the next prompt, say 9Delete9 and follow the
prompts.
• After the 9Ready9 prompt and the following beep, say
9Setup Select Phone9 and follow the prompts. • You can also press the 8Voice Recognition’ button
anytime while the list is being played and then choose
• You can also press the 8Voice Recognition’ button
the phone you wish to delete.
anytime while the list is being played, and then choose
the phone that you wish to select. Things You Should Know About Your UConnect™
System
• The selected phone will be used for the next phone
call. If the selected phone is not available, the UCon- Voice Training
nect™ system will return to using the highest priority For users experiencing difficulty with the system recog-
phone present in or near (approximately with in 30 nizing their voice commands or numbers, the UCon-
feet) the vehicle. nect™ system Voice Training feature may be used. To
enter this training mode, follow one of the two proce-
Delete UConnect™ Paired Cellular Phones
dures:
• Press the ’Phone’ button to begin.
From outside the UConnect™ mode (e.g. from radio
• After the 9Ready9 prompt and the following beep, say mode)
9Setup Phone Pairing.9
• Press and hold the ‘Voice Recognition’ button for 5
seconds until the session begins, or,
• Press the ‘Voice Recognition’ button and say 9Setup, • Speak normally, without pausing, just as you would
Voice Training9 command. speak to a person sitting approximately eight (8) feet
away from you.
Repeat the words and phrases when prompted by the
UConnect™ system. For best results, the Voice Training • Make sure that no one other than you is speaking
session should be completed when the vehicle is parked, during a voice recognition period.
engine running, all windows closed, and the blower fan
3
• Performance is maximized under:
switched off.
• low-to-medium blower setting,
This procedure may be repeated with a new user. The
system will adapt to the last trained voice only. • low-to-medium vehicle speed,
To restore the Voice Recognition system to factory default • low road noise,
settings, enter the Voice Training session via the above
• smooth road surface,
procedure and follow the prompts.
• fully closed windows,
Voice Recognition (VR)
• dry weather condition.
• Always wait for the beep before speaking.
• Even though the system is designed for users speaking
in North American English, French, and Spanish ac-
cents, the system may not always work for some.
• When navigating through an automated system, such Far End Audio Performance
as voice mail, or when sending a page at the end of
• Audio quality is maximized under:
speaking the digit string, make sure to say 9send.9
• low-to-medium blower setting.
• Storing names in phonebook when vehicle is not in
motion is recommended. • low-to-medium vehicle speed.
• It is not recommended to store similar sounding • low road noise.
names in the UConnect™ phonebook.
• smooth road surface.
• UConnect™ phonebook nametag recognition rate is
• fully closed windows.
optimized for the voice of the person who stored the
name in the phonebook. • dry weather condition.
• You can say 9O9 (letter 9O9) for 909 (zero). 98009 must be • operation from driver seat.
spoken 9eight-zero-zero.9
• Performance, such as audio clarity, echo, and loudness
• Even though international dialing for most number to a large degree rely on the phone and network, and
combinations is supported, some shortcut dialing not the UConnect™ system.
number combinations may not be supported.
• Echo at far end can sometime be reduced by lowering
the in-vehicle audio volume.
SEATS
10–Way Driver’s Power Seat — If Equipped
The driver’s power seat switches are located on the
driver’s front door trim panel. The bottom switch con-
trols up/down, forward/rearward, and tilt adjustment.
The top switch controls the seatback recline adjustment
3
and the middle switch controls the lumbar adjustment.
Heated Seats — If Equipped Press the switch once to select a heat setting (high or low)
This feature heats the driver, front passenger and second and press the switch a second time in the same direction
row seats. The controls for the front heated seats are to turn the heated seat off. The indicator light will show
located on the door trim panel next to the power seat when LOW or HIGH heat is ON.
switches.
The controls for the second row heated seats are located
on the center console between the seats. Press the switch
once to select a heat setting (high or low) and press the
switch a second time in the same direction to turn the
heated seat off. The indicator light will show when LOW
or HIGH heat is ON.
NOTE:
• If the lights in the second row heated seat switch begin
to flash when the switch is pressed, it indicates that the
heated seat is not functioning properly and that ser-
vice is required. See your authorized dealer for service.
• Once a heat setting is selected, heat will be felt within
3
2 to 3 minutes.
• The heated seats will turn off when the ignition switch
is turned to the OFF position.
WARNING!
WARNING!
5. Pull up on the release handle labeled “2” and lift To relatch the seat, tilt the seat rearward and push down
firmly to tumble the seat fully forward. If the seat firmly to engage the rear attachments. Then lift the
contacts the rear of the front seat, move the front seat seatback release lever labeled “1” and pull the seatback
forward. up to return it to its full upright position.
WARNING!
To raise the 3rd row seat, lift up on the seatback and push
rearward until the seatback is latched. Move the seatback
forward to be sure the seatback is fully latched.
CAUTION!
3. Pull on the load floor strap and lift the panel from the Plastic Grocery Bag Retainer
driver’s second row seatback over the center console and Retainer hooks which will hold plastic grocery bag
onto the passenger second row seat. handles are built into the seatbacks of all front seats. The
floor supports the partial weight of the bagged goods.
DRIVER MEMORY SEAT — IF EQUIPPED The memory seat buttons located on the driver’s door
If your vehicle is equipped with memory systems, your will always recall stored settings. The remote keyless
remote keyless entry transmitter or memory seat buttons entry transmitter can be programmed to recall positions
on the driver’s door panel can be used to recall the when the UNLOCK button is pressed. Refer to the
driver’s seat, outside mirrors, adjustable pedals (if following procedure on how to link a remote keyless
equipped) and radio station presets to saved positions. entry transmitter to a position. 3
NOTE: The vehicle must be in Park to recall memory
positions. If a recall is attempted when the vehicle is not
in Park, a message will be displayed in the Electronic
Vehicle Information Center (EVIC).
To recall memory positions press memory button number
1 if you are recalling the memory position for driver one
or press memory button number 2 if you are recalling the
memory position for driver two. A recall can be cancelled
by pressing any of the memory buttons during a recall.
When a recall is cancelled, the seat stops moving and a
delay of approximately one second will occur before any
Driver Memory Switches other recalls can be selected.
Your vehicle has been delivered with two remote keyless 5. Turn the ignition switch to the OFF position and
entry transmitters. One or both transmitters can be linked remove the key.
to either memory position. Up to eight remote keyless
6. Press and release the SET (S) button located on the
entry transmitters can be used with your vehicle. The
driver’s door. A light in the button will flash telling you
memory seat system can also accommodate up to eight
that you are in the set memory mode. You have five
transmitters linked to either of the two stored seat
seconds to complete the next step.
positions or any combination of the two positions.
7. Within 5 seconds, press and release button 1 or 2 on
To Program Memory Seat Buttons & RKE
the driver’s door. A chime will sound signaling you that
Transmitters, Follow These Steps:
the driver memory has been set. A message will also be
1. Turn the ignition switch to the ON position. displayed in the Electronic Vehicle Information Center
(EVIC), indicating a position has been set.
2. Select Remote Linked to Memory from the EVIC and
enter “Yes”. 8. Within 5 seconds, press and release the LOCK button
on one of the Remote Keyless Entry Transmitters. A
3. Use the seat, mirror and adjustable pedal switches to
chime will sound signaling you that the transmitter has
adjust the seat, recliner, side view mirrors and adjustable
been successfully linked. A message will also be dis-
pedals to the desired positions.
played in the Electronic Vehicle Information Center
4. Set the radio station presets. (EVIC), indicating the transmitter has been linked.
Repeat the above steps for the second position using the 5. Within 5 seconds, press and release button 1 or 2 on
other driver’s door numbered button and Remote Key- the driver’s door. A chime will sound signaling you that
less Entry Transmitter. the driver memory has been set. A message will also be
displayed in the EVIC, indicating a position has been set.
Each time the SET (S) button and a numbered button are
pressed, you erase the old memory and store a new one. 6. Within 5 seconds, press and release the UNLOCK
button on the remote keyless entry transmitters. A chime
3
To Disable A Transmitter Link, Follow These Steps:
will sound signaling you that the transmitter link has
1. Turn the ignition switch to the ON position. been successfully disabled. A message will also be dis-
played in the EVIC, indicating the transmitter has been
2. Select “Remote Linked To Memory” from the Elec-
disabled.
tronic Vehicle Information Center (EVIC), Customer Pro-
grammable features and enter “YES.”. To disable another transmitter from memory positions 1
or 2, repeat the above steps for each transmitter.
3. Turn the ignition switch to the OFF position and
remove the key. NOTE: This function can be selected using the “Cus-
tomer Programmable Features” in the EVIC section,
4. Press and release the SET(S) button located on the
otherwise see your authorized dealer for assistance.
driver’s door. A light in the button will flash telling you
that you are in the set memory mode. You have five
seconds to complete the next step.
Easy Exit Seat (Available with Memory Seat Only) removed from the ignition switch. The seat will move
This feature provides automatic driver’s seat positioning forward to the memory/driving position when the
which will enhance driver mobility out of and into the key is placed into the ignition and turned out of the
vehicle. LOCK position.
There are two possible Easy Exit and Easy Entry adjust- The Easy Entry and Easy Exit feature will be automati-
ments available: cally disabled if the seat is already positioned closer than
2.5 inches (60 mm) forward of the rear stop. At this
• The seat cushion will move rearward approximately
position there is no benefit to the driver by moving the
2.5 inches (60 mm) if the starting position of the seat is
seat for Easy Exit or Easy Entry.
greater than or equal to 4.72 inches (120 mm) forward
of the rear seat stop when the key is removed from the Each stored memory setting will have an associated Easy
ignition switch. The seat will then move forward Entry and Easy Exit position.
approximately 2.5 inches (60 mm) when the key is
NOTE: The Easy Exit Seat feature is not enabled when
placed into the ignition and turned out of the LOCK
the vehicle is delivered from the factory. The Easy Exit
position.
Seat feature can be enabled or disabled through the
• The seat shall move to the position located 1 1/8 customer programmable features in the Electronic Ve-
inches (30 mm) forward of the rear stop if the starting hicle Information Center (EVIC), refer to “Easy Exit
position is between 2.5 inches to 4.72 inches (60 mm to Seat?” under “Use Factory Settings”.
120 mm) forward of the rear stop when the key is
Tilt Mirrors in Reverse (Available with Memory TO OPEN AND CLOSE THE HOOD
Seat Only) — If Equipped To open the hood, two latches must be released. First pull
This additional feature provides automatic outside mir- the hood release lever located under the left side of the
ror positioning which will aid the driver’s view of the instrument panel.
ground rearward of the front doors. The outside mirrors
will move slightly downward from the present position 3
when the vehicle is shifted into the Reverse position. The
outside mirrors will then return to the original position
when the vehicle is shifted out of Reverse position. Each
stored memory setting will have an associated Tilt Mir-
rors in Reverse position.
NOTE: The Tilt Mirrors in Reverse feature is not en-
abled when delivered from the factory. The Tilt Mirrors in
Reverse feature can be enabled or disabled through the
customer programmable features in the Electronic Ve-
hicle Information Center (EVIC), refer to “Tilt Mirrors in
Hood Release Lever
Reverse?” under “Use Factory Settings”.
Next, push to the left the safety catch located under the cm (6 inches) and then drop it. This should secure both
front edge of the hood, near the center. latches. Never drive your vehicle unless the hood is fully
closed, with both latches engaged.
WARNING!
LIGHTS
Overhead Console Map/Reading Lights
Hood Safety Catch
These lights are mounted between the sun visors on the
Use the hood prop rod to secure the hood in the open overhead console. Each light is turned ON by pressing
position. the lens. Press the lens a second time to turn the light
To prevent possible damage, do not slam the hood to
close it. Lower the hood until it is open approximately 15
OFF. The lights also turn on when a door is opened or the NOTE: The lights will remain on until the switch is
dimmer control is turned fully upward, past the second pressed a second time, so be sure they have been turned
detent. off before leaving the vehicle.
Interior Lights
The interior lights come on when a door is opened.
3
The interior lights will automatically turn off in about 15
minutes if a door is left open or the dimmer control is left
in the Dome light position. Turn the ignition switch ON
to restore the interior light operation.
Map/Reading Lights
NOTE: The engine must be running before the head- To activate the delay feature, turn off the ignition switch
lights will come ON in the Automatic mode. while the headlights are still on. Then turn off the
headlights within 45 seconds. The 90 second delay inter-
Daytime Running Lights (Canada Only)
val begins when headlight switch is turned off. If the
The high beam headlights will come on as Daytime
headlights or park lights are turned back on or the
Running Lights whenever the ignition switch is on, the
ignition switch is turned on, the delay will be cancelled.
headlights are off, and the parking brake is off. The
headlight switch must be used for normal night time If the headlights are turned off before the ignition, they
driving. will turn off in the normal manner.
Lights-on Reminder NOTE: The lights must be turned off within 45 seconds
If the headlights or parking lights are on after the ignition of turning the ignition off to activate this feature
is turned OFF, a chime will sound to alert the driver
Fog Lights — If Equipped
when the driver’s door is opened.
The front fog light switch is on the Multi-Function
Headlight Time Delay Lever. To activate the front fog lights, turn on the
This feature provides the safety of headlight illumination parking lights or the low beam headlights and pull
for up to 90 seconds, when leaving your vehicle in an out the end of the Multi-Function Lever.
unlighted area.
NOTE: The fog lights will only operate with the head- NOTE: If a turn signal has been left on for at least a mile
lights on low beam. Selecting high beam headlights will duration, a continuous chime will sound.
turn off the fog lights.
Turn Signal Lane Change Auto-Mode
Turn Signals Momentarily engage the multifunction control lever par-
Move the lever up or down to signal a right-hand or tially up or down to activate the lane change feature
left-hand turn. without holding the lever. The signal will flash 3 times,
3
and automatically turn off.
The arrow on either side of the instrument cluster flashes
to indicate the direction of the turn, and proper operation Highbeam/Lowbeam Select Switch
of the front and rear turn signal lights. If an indicator fails Pull the Multi-Function Lever towards you to switch the
to light when the lever is moved, it would suggest that headlights to HIGH beam. Pull the Lever a second time
the switch or indicator lamp is defective. to switch the headlights to LOW beam.
If a defective bulb or wiring circuit is detected for the Passing Light
turn signal system, the arrow indicators will flash at a You can signal another vehicle with your headlights by
faster rate. lightly pulling the Multi-Function Lever toward you.
This will cause the headlights to turn on at high beam
You can signal a lane change by moving the lever
and remain on until the lever is released.
partially up or down.
WARNING!
WARNING! WARNING!
Your motorized door or gate will open and close Vehicle exhaust contains carbon monoxide, a danger-
while you are training the Universal Transceiver. Do ous gas. Do not run your vehicle in the garage while
not train the transceiver if people or pets are in the training the transceiver. Exhaust gas can cause seri-
path of the door or gate. Only use this transceiver ous injury or death. 3
with a garage door opener that has a “stop and
reverse” feature as required by federal safety stan-
dards. This includes most garage door opener models Programming HomeLinkT
manufactured after 1982. Do not use a garage door Before You Begin
opener without these safety features. Call toll-free If you have not trained any of the HomeLinkt buttons,
1–800–355–3515 or, on the Internet at erase all channels before you begin training.
www.HomeLink.com for safety information or
assistance. To do this, press and hold the two outside buttons for 20
seconds until the red HomeLinkt indicator begins to
flash, or the EVIC message changes from “CLEARING
CHANNELS” to “CHANNELS CLEARED.”
It is recommended that a new battery be placed in the
hand-held transmitter of the device being programmed
to HomeLinkt for more efficient training and accurate Then release both the HomeLinkt and hand-held trans-
transmission of the radio-frequency signal. mitter buttons.
Your vehicle should be parked outside of the garage If the EVIC display states “DID NOT TRAIN” repeat
while training. Step 3. If the signal is too weak, replace the battery in the
original hand-held transmitter.
1. Turn the ignition switch to the ON/RUN position.
It may take up to 30 seconds, or longer in rare cases. The
2. Place the hand-held transmitter 1–3 inches (3–8 cm)
garage door may open & close while you train.
from the HomeLinkt buttons while keeping the indicator
in view. NOTE: Some gate operators and garage door openers
may require you to replace Step #3 with procedures
For optimal training, point the battery end of the hand-
noted in the “Gate Operator/Canadian Programming”
held transmitter away from the HomeLinkt.
section.
3. Simultaneously press and hold both the chosen
4. Press and hold the newly-trained HomeLinkt button.
HomeLinkt button and the hand-held transmitter button
If the channel has been trained, the EVIC display will
until the until the red HomeLinkt indicator changes from
now state “CHANNEL # TRANSMIT.”
a slow to a rapid flash rate or the EVIC display changes
from “CHANNEL # TRAINING” to “CHANNEL # If the EVIC display still states “CHANNEL # TRAIN-
TRAINED.” ING” repeat Step 3.
7. Return to the vehicle and press the programmed Canadian Programming/Gate Programming
HomeLinkt button twice (holding the button for 2 sec- Canadian radio-frequency laws require transmitter sig-
onds each time). If the device is plugged in and activates, nals to 9time-out9 (or quit) after several seconds of
programming is complete. transmission which may not be long enough for
HomeLinkt to pick up the signal during programming.
If the device does not activate, press the button a third
Similar to this Canadian law, some U.S. gate operators are
time (for 2 seconds) to complete the training.
designed to 9time-out9 in the same manner.
NOTE: If you are have any problems, or require assis-
It may be helpful to unplug the device during the cycling
tance, please call toll-free 1–800–355–3515 or, on the
process to prevent possible overheating of the garage
Internet at www.HomeLink.com for information or assis-
door or gate motor.
tance.
If you are having difficulties programming a garage door
To program the remaining two HomeLinkt buttons,
opener or a gate operator, replace “Programming
repeat each step for each remaining button. DO NOT
HomeLink” Step 3 with the following:
ERASE THE CHANNELS.
3. Continue to press and hold the HomeLinkt button
while you press and release - every two seconds
(“cycle”) your hand-held transmitter until HomeLinkt
has successfully accepted the frequency signal. The red
HomeLinkt indicator will change from a slow to rapid
flash, and the EVIC display in the cluster will change Reprogramming a Single HomeLinkT Buttons
from “CHANNEL # TRAINING” to “CHANNEL # To re-program a channel that has been previously
TRAINED.” trained, follow these steps:
If you unplugged the device for training, plug it back in 1. Turn the ignition switch to the ON/RUN position.
at this time.
2. Press and hold the desired HomeLinkt button for 20 3
Then proceed with the remaining steps. seconds until the red indicator starts to flash, or the EVIC
display states “CHANNEL # TRAINING.”DO NOT
Using HomeLinkT
RELEASE THE BUTTON.
To operate, simply press and release the programmed
HomeLinkt button. Activation will now occur for the 3. WITHOUT RELEASING THE BUTTON, proceed
trained device (i.e. garage door opener, gate operator, with PROGRAMMING HOMELINK Step #2 and fol-
security system, entry door lock, home/office lighting, low all remaining steps.
etc.). The hand-held transmitter of the device may also be
Security
used at any time.
It is advised to erase all channels before you sell or turn
in your vehicle.
To do this, press and hold the two outside buttons for 20 If you are have any problems, or require assistance,
seconds until the EVIC message states “CHANNELS please call toll-free 1–800–355–3515 or, on the Internet at
CLEARED.” Note that all channels will be erased. Indi- www.HomeLink.com for information or assistance.
vidual channels cannot be erased.
General Information
The HomeLinkt Universal Transceiver is disabled when This device complies with FCC rules part 15 and Industry
the Vehicle Theft Alarm is active. Canada RSS-210. Operation is subject to the following
two conditions:
Troubleshooting Tips
If you are having trouble programming HomeLinkt, here 1. This device may not cause harmful interference
are some of the most common solutions:
2. This device must accept any interference that may be
• Replace the battery in the original transmitter. received including interference that may cause undesired
operation
• Press the Learn Button on the Garage Door Opener to
complete the training for Rolling Code. NOTE: The transmitter has been tested and it complies
with FCC and IC rules. Changes or modifications not
• Did you unplug the device for training, and remember
expressly approved by the party responsible for compli-
to plug it back in?
ance could void the user’s authority to operate the
device.
ELECTRONIC BRAKE CONTROL SYSTEM - brake of the spinning wheel. This will allow more engine
ABS/TCS/BAS/ESP torque to be applied to the wheel that is not spinning.
Your vehicle is equipped with the advanced electronic
Brake Assist System (BAS)
brake control system that includes Anti-Lock Brake Sys-
The BAS is designed to optimize the vehicle’s braking
tem (ABS), Traction Control System (TCS) Brake Assist
capability during emergency braking maneuvers. The
System (BAS), and Electronic Stability Program (ESP). All
system detects an emergency braking situation by sens-
four systems work together to enhance vehicle stability
ing the rate and amount of brake application and then
and control in various driving conditions, and are com-
applies optimum pressure to the brakes. This can help
monly referred to as ESP.
reduce braking distances. The BAS complements the
Traction Control System (TCS) anti-lock brake system (ABS). Applying the brakes very
This system monitors the amount of wheel spin of each of quickly results in the best BAS assistance. To receive the
the driven wheels. If wheel spin is detected, brake benefit of the system, you must apply continuous brak-
pressure is applied to the slipping wheel(s) and engine ing pressure during the stopping sequence. Do not
power is reduced to provide enhanced acceleration and reduce brake pedal pressure unless braking is no longer
stability. A feature of the TCS system functions similar to desired. Once the brake pedal is released, the BAS is
a limited slip differential and controls the wheel spin deactivated.
across a driven axle. If one wheel on a driven axle is
spinning faster than the other, the system will apply the
raised, and the “ESP/TCS Indicator Light” will be illu- situation requiring ESP to be switched to the “Partial
minated. This mode is intended to be used for a more ESP” mode is overcome, turn ESP back on by momen-
spirited driving experience, or if the vehicle is in deep tarily depressing the “ESP OFF” button. This may be
done while the vehicle is in motion.
snow, sand, or gravel conditions and more wheel spin
that ESP would normally allow is required. ESP/BAS Warning Light and ESP/TCS Indicator
Light
To turn ESP on again, momentarily depress the The malfunction indicator for the ESP is combined with
“ESP OFF” button. the BAS indicator. The yellow “ESP/BAS Warning
Lamp” and the yellow “ESP/TCS Indicator Light” in the
WARNING! instrument cluster both come on when the ignition
switch is turned to the “ON” position. They should both
In the Partial ESP mode, the engine torque reduction go out with the engine running. If the “ESP/BAS Warn-
and stability features are desensitized. Therefore, the ing Lamp” comes on continuously with the engine
enhanced vehicle stability offered by ESP is running, a malfunction has been detected in either the
unavailable. ESP or BAS system, or both. If this light remains on after
several ignition cycles, and the vehicle has been driven
NOTE: To improve the vehicle’s traction when driving several miles at speeds greater than 30 mph (48 km/h),
with snow chains, or starting off in deep snow, sand or see your authorized dealer as soon as possible to have the
gravel, it may be desirable to switch to the “Partial ESP” problem diagnosed and corrected.
mode by pressing the “ESP OFF” button. Once the
NOTE:
• The “ESP Indicator Light” and the “ESP/BAS Warning
Light” come on momentarily each time the ignition
switch is turned ON.
• Each time the ignition is turned ON, the ESP System
will be ON even if it was turned off previously.
3
• The ESP Control System will make buzzing or clicking
sounds when it is active. This is normal; the sounds
will stop when ESP becomes inactive following the
maneuver that caused the ESP activation.
The Rear Park Assist System can be active only when the
transaxle shift lever is in R (Reverse). If the Rear Park
Assist System is enabled at this shift position, the system
will be active until the vehicle speed is increased to
approximately 11 mph (18 km/h) or above. The system
will be active again if the vehicle speed is decreased to 3
speeds less than approximately 10 mph (16 km/h).
Rear Park Assist Sensors
The four Rear Park Assist Sensors, located in the rear
fascia, monitor the area behind the vehicle that is within
the sensors’ field of view. The monitored area seems oval
in shape. The sensors can detect obstacles from approxi- Rear Park Assist LEDs
mately 11.8 inches (30 cm) up to 59 inches (150 cm) from
the rear fascia in the horizontal direction, depending on
the location and orientation of the obstacle and the type
of obstacle.
Rear Park Assist Warning Display The driver can view the LEDs either through the rear
The Rear Park Assist Warning Display, located in the view mirror or by looking at the display above the rear
headliner near the liftgate glass, provides both visual and window.
audible warnings to indicate the distance between the
The system dimly illuminates the two outer most yellow
rear fascia and the detected obstacle.
LEDs when it is ON and detecting no obstacles. The
When the ignition is changed to the RUN/ON position, following chart shows the warning display operation
the warning display will turn ON all of its LEDs for when the system is detecting an obstacle:
about 1 second. Each side of the warning display has 6
yellow and 2 red LEDs. The vehicle is close to the obstacle
when the red LED is ON.
WARNING! CAUTION!
• Drivers must be careful when backing up even when • To avoid vehicle damage the Rear Park Sense
using the Rear Park Sense System. Always check System should only be used as a parking aid and
carefully behind your vehicle, and be sure to check is unable to recognize every obstacle, including
for pedestrians, animals, other vehicles, obstructions,
or blind spots before backing up. You are respon- small objects. Parking curbs might be temporarily
sible for the safety of your surroundings and must detected or not detected at all. Obstacles located
continue to pay attention while backing up. Failure above or below the sensors will not be detected
to do so can result in serious injury or death. when they are in close proximity to the rear of the
• Before using the Rear Park Sense System, it is vehicle.
strongly recommended that the ball mount and hitch
ball assembly be disconnected from the vehicle
• To avoid vehicle damage the vehicle must be
when the vehicle is not used for towing. Failure to do driven slowly when using the Rear Park Sense
so can result in injury or damage to vehicles or System to be able to stop in time when an obstacle
obstacles because the hitch ball will be much closer is detected. It is recommended that the driver look
to the obstacle than the rear fascia when the warning over his/her shoulder when using the Rear Park
display turns the red LEDs ON. Also, the sensors
Sense System.
could detect the ball mount and hitch ball assembly,
depending on its size and shape, giving a false
indication that an obstacle is behind the vehicle.
If (SERVICE PARK ASSIST SYSTEM( appears in the NOTE: Refer to “Setting Display Properties” under
Electronic Vehicle Information Center (EVIC) after mak- “System Settings” in the Navigation User’s Manual for
ing sure the rear bumper is clean please see your autho- instructions regarding navigation screen brightness ad-
rized dealer. justments.
Cleaning the Rear Park Assist System Use the following steps to access the Rear Backup Cam-
Clean the Rear Park Assist Sensors with water, car wash era feature:
soap and a soft cloth. Do not use rough or hard cloths. Do
1. Start the engine.
not scratch or poke the sensors, otherwise, you could
damage the sensors. 2. Place shift lever in R (Reverse).
REAR CAMERA — IF EQUIPPED 3. Wait one to two seconds, and the camera view will
Your vehicle may be equipped with a Rear Camera display on the instrument cluster.
system that allows you to see an on-screen image (located NOTE: The camera view will display only while the
in the center of the instrument cluster) of the rear of your vehicle is in R (Reverse).
vehicle whenever it is put into R (Reverse). The camera is
located in the light bar over the rear license plate. 4. Perform a visual check of the rear area.
NOTE: CHECK ENTIRE SURROUNDINGS before
backing up.
5. Backup as necessary.
CAUTION!
6. Place the sift lever in P (Park) or D (Drive) to exit the
Rear Backup Camera system. • To avoid vehicle damage the Rear Camera System
should only be used as a parking aid and is unable
WARNING! to view every obstacle, or object in your drive
path. 3
Drivers must be careful when backing up even when • To avoid vehicle damage the vehicle must be
using the Rear Camera System. Always check care- driven slowly when using the Rear Camera Sys-
fully behind your vehicle, and be sure to check for tem to be able to stop in time when an obstacle is
pedestrians, animals, other vehicles, obstructions, or seen. It is recommended that the driver look fre-
blind spots before backing up. You are responsible quently over his/her shoulder when using the Rear
for the safety of your surroundings and must con- Camera System.
tinue to pay attention while backing up. Failure to do
so can result in serious injury or death.
NOTE: If snow, ice, mud, or anything else builds up on
the camera lens, clean the lens, rinse with water, and dry
with a soft cloth. Do not cover the lens.
POWER SUNROOF — IF EQUIPPED Press and hold the “OPEN” button rearward to fully
The power sunroof buttons are located between the sun open the sunroof. The sunroof can be stopped at any
visors on the overhead console. position between closed and full open. Momentarily
pressing the “OPEN” button rearward will activate the
Express Open Feature, causing the sunroof to open
automatically. 3
Press and hold the “VENT” button to open the vent. The
sunroof can be stopped at any position between closed
and full vent. To close the sunroof from the vent position,
press and hold the “CLOSE” button forward. Releasing
the button will stop the movement of the sunroof and the
sunroof will remain in the partial vent position until the
button is pushed forward again.
NOTE: The power sunroof buttons remain active for up
Power Sunroof buttons to 45 seconds after the ignition button has been turned
off. Opening either front door will cancel this feature.
Express Open Feature To close the sunroof, press and hold the “CLOSE” button
The sunroof is equipped with an intermediate stop or forward. Again, any release of the button will stop the
comfort stop position. This feature is designed to elimi- movement and the sunroof will remain in a partial open
nate wind buffeting at vehicle speeds between 20-40 mph condition until the button is pushed forward again.
(32-64 km/h). To operate this feature, momentarily press
The sunshade can be opened manually. It will also open
the “OPEN” button rearward to activate the Express
as the sunroof opens. The sunshade cannot be closed if
Open Feature and the glass will automatically stop at the
the sunroof is open.
comfort stop position. Pressing the button rearward
again will fully open the sunroof.
During the Express Open operation, any movement of
the button will stop the sunroof and it will remain in a
partial open position. Again, momentarily pressing the
button rearward will activate the Express Open Feature.
Wind Buffeting
WARNING!
Wind buffeting can be described as the perception of
• NEVER leave children alone in a vehicle. Occu- pressure on the ears or a helicopter type sound in the
pants, particularly unattended children, can be- ears. Your vehicle may exhibit wind buffeting with the
come entrapped by the power sunroof while oper- windows down, or the sunroof (if equipped) in certain
ating the power sunroof switch. Such entrapment open or partially open positions. This is a normal occur- 3
may result in serious injury or death. Don’t leave rence and can be minimized. If the buffeting occurs with
the keys in the ignition. A child could operate the rear windows open, open the front and rear windows
power windows, other controls, or move the ve- together to minimize the buffeting. If the buffeting occurs
hicle with the sunroof open, adjust the sunroof opening to
minimize the buffeting or open any window.
• In an accident, there is a greater risk of being
thrown from a vehicle with an open sunroof. You Sunroof Comfort Position — If Equipped
could also be seriously injured or killed. Always If equipped, some model sunroofs will stop at a prede-
fasten your seat belt properly and make sure all termined comfort position — not allowing the sunroof to
passengers are properly secured too. open to the full retracted glass position. The comfort
• Do not allow small children to operate the sunroof. position stops the sunroof glass at approximately 3/4
Never allow fingers or other body parts, or any open position. This will allow for minimal wind buffet-
object to project through the sunroof opening. ing.
Injury may result.
Sunroof Maintenance
Use only a non-abrasive cleaner and a soft cloth to clean
the glass panel.
The outlets include tethered caps labeled with a key or Electrical Outlet Use With Engine Off
battery symbol indicating the power source. The passen-
ger side instrument panel and center console outlets are CAUTION!
powered directly from the battery, items plugged into
these outlets may discharge the battery and/or prevent • Many accessories that can be plugged in draw power
from the vehicle’s battery, even when not in use (i.e.
engine starting. cellular phones, etc.). Eventually, if plugged in long 3
enough, the vehicle’s battery will discharge suffi-
The passenger side and center console outlets are pro- ciently to degrade battery life and/or prevent engine
tected by an automatic reset circuit breaker. The auto- starting.
matic circuit breaker restores power when the overload is • Accessories that draw higher power (i.e. coolers,
removed. vacuum cleaners, lights, etc.), will degrade the battery
even more quickly. Only use these intermittently and
NOTE: If desired, the fourth power outlet in the rear with greater caution.
cargo area can be converted by your authorized dealer to • After the use of high power draw accessories, or long
periods of the vehicle not being started (with accesso-
provide power with the ignition switch in the OFF ries still plugged in), the vehicle must be driven a
position. sufficient length of time to allow the alternator to
recharge the vehicle’s battery.
• Power outlets are designed for accessory plugs only.
Do not hang any type of accessory or accessory bracket
from the plug. Improper use of the power outlet can
cause damage.
On vehicles equipped with six passenger seating the Rear Cargo Storage Bin — If Equipped
second row seat cupholders are located in the forward The storage bin is located in the floor of the rear cargo
edge of the center console located between the second area. To open lift up on the handle.
row seats. Push down on the forward edge of the console
to release the cupholders. Press the cover up when the
cupholders are no longer needed. 3
Third Row Seat Cupholders — If Equipped
There are cupholders located in each rear trim panel for
the third row seat passengers.
STORAGE
Console Features
The center consoles may be equipped with a tissue
holder mounted on the underside of the cover. The
bottom of the console bins may also have built in holders Rear Storage Bin
for compact discs or cassette tapes.
• Place as much cargo as possible in front of the rear ROOF LUGGAGE RACK — IF EQUIPPED
axle. Too much weight or improperly placed weight The crossbars and siderails are designed to carry the
over or behind the rear axle can cause the rear of the weight on vehicles equipped with a luggage rack. The
vehicle to sway. load must not exceed 150 lbs (68 kg), and should be
uniformly distributed over the luggage rack crossbars.
• Do not pile luggage or cargo higher than the top of the
seatback. This could impair visibility or become a
dangerous projectile in a sudden stop or collision.
WARNING!
Roof Rack
Distribute cargo weight evenly on the roof rack crossbars. Attempt to move the crossbar again to ensure that it has
The roof rack does not increase the total load carrying properly locked into position.
capacity of the vehicle. Be sure the total load of cargo
NOTE: To reduce the amount of wind noise when the
inside the vehicle plus that on the external rack does not
cross bars are not in use, move both cross bars next to
exceed the maximum vehicle load capacity.
each other towards the rear of the vehicle in the rear most
To move the cross bars, press the upper edge of each position.
3
cross bar button, then move the cross bar to the desired
The tie down holes on the cross bar ends should always
position, keeping the crossbars parallel to the rack frame.
be used to tie down the load. Check the straps frequently
This is can be done with one person standing on each
to be sure that the load remains securely attached.
side of the vehicle, moving the cross bar at the same time.
Once the cross bar is in place, press the lower edge of the
cross bar button to lock it into position.
CAUTION! WARNING!
• Crossbars should remain equally spaced or parallel Cargo must be securely tied before driving your ve-
at any luggage rack position for proper function. hicle. Improperly secured loads can fly off the vehicle,
Noncompliance could result in damage to the lug- particularly at high speeds, resulting in personal in-
gage rack, cargo and/or vehicle.
jury or property damage. Follow the Roof Rack Cau-
• To avoid damage to the roof rack and vehicle, do not tions when carrying cargo on your roof rack.
exceed the maximum roof rack load capacity of 150
lbs (68 kg). Always distribute heavy loads as evenly
as possible and secure the load appropriately. LOAD LEVELING SYSTEM
• Long loads which extend over the windshield, such The automatic load leveling system will provide a level
as wood panels or surfboards, or loads with large riding vehicle under most passenger and cargo loading
frontal area should be secured to both the front and conditions.
rear of the vehicle.
A hydraulic pump contained within the shock absorbers
• Travel at reduced speeds and turn corners carefully raises the rear of the vehicle to the correct height. It takes
when carrying large or heavy loads on the roof rack. approximately 1 mile (1.6 km) of driving for the leveling
Wind forces, due to natural causes or nearby truck to complete depending on road surface conditions.
traffic, can add sudden upward lift to loads. This is
especially true on large flat loads and may result in If the leveled vehicle is not moved for approximately 15
damage to the cargo or your vehicle. hours, the leveling system will bleed itself down. The
vehicle must be driven to reset the system.
CONTENTS
m Instrument Panel And Controls . . . . . . . . . . . . . 184 ▫ Mini-Trip Functions — If Equipped . . . . . . . . 208
4
m Base Instrument Cluster . . . . . . . . . . . . . . . . . . 185 m Setting The Analog Clock . . . . . . . . . . . . . . . . . 209
m Premium Instrument Cluster . . . . . . . . . . . . . . . 186 m Electronic Digital Clock . . . . . . . . . . . . . . . . . . 209
m Instrument Cluster Descriptions . . . . . . . . . . . . 187 ▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 210
m Electronic Vehicle Information Center (EVIC) — m Radio General Information . . . . . . . . . . . . . . . . 210
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . 210
▫ Oil Change Required . . . . . . . . . . . . . . . . . . . 202
▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . 211
▫ Customer Programmable Features —
▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 211
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 203
▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 211
▫ Compass Display — If Equipped . . . . . . . . . . 207
is not functioning and that service is required. However, indicated by the Brake Warning Light which will turn on
the conventional brake system will continue to operate when the brake fluid level in the master cylinder has
normally if the BRAKE warning light is not on. dropped below a specified level.
If the ABS light is on, the brake system should be serviced The light will remain on until the cause is corrected.
as soon as possible to restore the benefits of Anti-Lock
NOTE: The light may flash momentarily during sharp
brakes. If the ABS light does not turn on when the
cornering maneuvers which change fluid level condi-
Ignition switch is turned to the ON position, have the 4
tions. The vehicle should have service performed.
light inspected by an authorized dealer.
If brake failure is indicated, immediate repair is neces-
7. Brake System Warning Light
sary.
This light monitors various brake functions,
including brake fluid level and parking brake
WARNING!
application. If the brake light turns on, it may
indicate that the parking brake is applied, there Driving a vehicle with the brake light on is danger-
is a low brake fluid level or there is a problem with the ous. Part of the brake system may have failed. It will
anti-lock brake system. take longer to stop the vehicle. You could have an
The dual brake system provides a reserve braking capac- accident. Have the vehicle checked immediately.
ity in the event of a failure to a portion of the hydraulic
system. Failure of either half of the dual brake system is
Vehicles equipped with Anti-Lock brakes (ABS), are also 8. Electronic Stability Program (ESP) Indicator
equipped with Electronic Brake Force Distribution (EBD). Light/Traction Control System (TCS) Indicator Light
In the event of an EBD failure, the Brake Warning Light If this indicator light flashes during accelera-
will turn on along with the ABS Light. Immediate repair tion, apply as little throttle as possible. While
to the ABS system is required. driving, ease up on the accelerator. Adapt your
speed and driving to the prevailing road con-
The operation of the Brake Warning Light can be checked
ditions, and do not switch off the ESP, or TCS.
by turning the ignition switch from the OFF position to
the ON position. The light should illuminate for approxi- NOTE: Extended heavy use of Traction Control may
mately two seconds. The light should then turn off unless cause the system to deactivate and turn on the Traction
the parking brake is applied or a brake fault is detected. Control Light. This is to prevent overheating of the brake
If the light does not illuminate, have the light inspected system and is a normal condition. The system will remain
by an authorized dealer. disabled for about 4 minutes until the brakes have
cooled. The system will automatically reactivate and turn
The light also will turn on when the parking brake is
off the Traction Control Light.
applied with the ignition switch in the ON position.
NOTE: This light shows only that the parking brake is
applied. It does not show the degree of brake application.
2. Fully depress the accelerator pedal slowly three Certain conditions such as a loose or missing gas cap,
times within 10 seconds. poor fuel quality, etc. may illuminate the light after
engine start. The vehicle should be serviced if the light
3. Turn the ignition switch to the LOCK position.
stays on through several of your typical driving cycles. In
NOTE: If the indicator message illuminates when you most situations the vehicle will drive normally and will
start the vehicle, the oil change indicator system did not not require towing.
reset. If necessary repeat this procedure.
The Malfunction Indicator Light flashes to alert you to 4
14. Cruise Indicator serious conditions that could lead to immediate loss of
This indicator shows that the Speed Control power or severe catalytic converter damage. The vehicle
System is ON. should be serviced as soon as possible if this occurs.
15. Malfunction Indicator Light 16. High Beam Light
This light is part of an onboard diagnostic system This light shows that the headlights are on high
called OBD that monitors engine and automatic beam. Pull the Multi-Function lever towards the
transmission control systems. The light will illu- steering wheel to switch the headlights from high or low
minate when the key is in the ON position before engine beam.
start. If the bulb does not come on when turning the key
from OFF to ON, have the condition checked promptly.
17. Navigation Screen/Rear View Camera — If vehicle and shut off the engine as soon as possible. A
Equipped continuous chime will sound when this light turns on.
The navigation system provides maps, turn identifica-
Do not operate the vehicle until the cause is corrected.
tion, selection menus and instructions for selecting a
This light does not show how much oil is in the engine.
variety of destinations and routes. Refer to your “Navi-
The engine oil level must be checked under the hood.
gation User’s Manual” for detailed operating instruc-
tions. 20. Seat Belt Reminder Light
When the ignition switch is first turned ON, this
The Rear View Camera system uses the Navigator Screen
light will turn on for 5 to 8 seconds as a bulb check.
to display the area behind the vehicle. Camera view will
During the bulb check, if the driver’s seat belt is
display only while the vehicle is in R (Reverse).
unbuckled, a chime will sound. After the bulb check or
18. Front Fog Light Indicator — If Equipped when driving, if the driver seat belt remains unbuckled,
This light shows the front fog lights are ON. the Seat Belt Warning Light will flash or remain on
continuously. Refer to 9Enhanced Driver Seat Belt Re-
minder System (BeltAlert™)9 in the Occupant Restraints
19. Oil Pressure Warning Light
section for more information.
This light shows low engine oil pressure. The light
should turn on momentarily when the engine is
started. If the light turns on while driving, stop the
21. Tire Pressure Monitoring Telltale Lamp reduces fuel efficiency and tire tread life, and may affect
Each tire, including the spare (if provided), the vehicle’s handling and stopping ability.
should be checked monthly when cold and
NOTE: Please note that the TPMS is not a substitute for
inflated to the inflation pressure recommended
proper tire maintenance, and it is the driver’s responsi-
by the vehicle manufacturer on the vehicle
bility to maintain correct tire pressure, even if underin-
placard or tire inflation pressure label. (If your vehicle
flation has not reached the level to trigger illumination of
has tires of a different size than the size indicated on the
the TPMS low tire pressure telltale. 4
vehicle placard or tire inflation pressure label, you should
determine the proper tire inflation pressure for those Your vehicle has also been equipped with a TPMS
tires.) malfunction indicator to indicate when the system is
combined with the low tire pressure telltale. When the
As an added safety feature, your vehicle has been
system detects a malfunction, the telltale will flash for
equipped with a tire pressure monitoring system (TPMS)
approximately one minute and then remain continuously
that illuminates a low tire pressure telltale when one or
illuminated. This sequence will continue upon subse-
more of your tires are significantly under-inflated. Ac-
quent vehicle start-ups as long as the malfunction exists.
cordingly, when the low tire pressure telltale illuminates,
When the malfunction indicator is illuminated, the sys-
you should stop and check your tires as soon as possible,
tem may not be able to detect or signal low tire pressure
and inflate them to the proper pressure. Driving on a
as intended. TPMS malfunctions may occur for a variety
significantly under-inflated tire causes the tire to over-
of reasons, including the installation of replacement or
heat and can lead to tire failure. Under-inflation also
For additional information on Tire Pressures, refer to chime, the engine temperature is critically hot, and the
Section 5 — Starting and Operating, “Tire Inflation vehicle should be turned off immediately. The vehicle
Pressures” of this manual. should be serviced as soon as possible.
22. Airbag Light 25. Liftgate Ajar — If Equipped
This light turns on and remains on for 6 to 8 This light turns on if the liftgate is not com-
seconds as a bulb check when the ignition pletely closed.
switch is first turned ON. If the light is not on 4
during starting, stays on, or turns on while
driving, have the system inspected by an authorized 26. Door Ajar Light — If Equipped
dealer as soon as possible. This light turns on if a door is not completely
closed.
23. Electronic Vehicle Information Center Display — If
Equipped 27. Washer Fluid Light — If Equipped
When the appropriate conditions exist, this display This light turns on when the washer fluid level
shows the Electronic Vehicle Information Center (EVIC) falls below approximately 1/4 filled. The light will
messages. remain on until fluid is added.
24. Engine Temperature Warning Light
This light warns of an overheated engine condi-
tion. If this light is accompanied by a continuous
28. Electronic Stability Program (ESP) Warning the vehicle has completely stopped and the gear selector
Light/Brake Assist System (BAS) Warning Light — If is placed in the PARK position. The light should turn off.
Equipped If the light remains lit with the engine running your
The malfunction lamp for the ESP is combined vehicle will usually be drivable, however, see your dealer
with BAS. The yellow “ESP/BAS Warning for service as soon as possible. If the light is flashing
Lamp” comes on when the ignition switch is when the engine is running, immediate service is re-
turned to the “ON” position. They should go quired and you may experience reduced performance, an
out with the engine running. If the “ESP/BAS Warning elevated/rough idle or engine stall and your vehicle may
Lamp” comes on continuously with the engine running, require towing. The light will come on when the ignition
a malfunction has been detected in either the ESP or the is first turned on and remain on briefly as a bulb check.
BAS system. If this light remains on after several ignition If the light does not come on during starting, have the
cycles, and the vehicle has been driven several miles at system checked by an authorized dealer.
speeds greater than 30 mph (48 km/h), see your autho-
30. All-Wheel-Drive Failure Indicator Light — If AWD
rized dealer as soon as possible.
equipped
29. Electronic Throttle Control (ETC.) Light This light monitors the All-Wheel-Drive
This light informs you of a problem with the (AWD) system. The light will come on, for a
Electronic Throttle Control system. If a prob- bulb check, when the ignition key is turned to
lem is detected the light will come on while the the ON position and may stay on for as long as
engine is running. Cycle the ignition key when 3 seconds.
When lit solid: There is an AWD system fault. AWD Pressing the MENU button will change the displayed
performance will be at a reduced level. Service the AWD programming features. Pressing the STEP button will
system soon. display the available choices. Pressing the MENU button
a second time accepts a selected choice.
When blinking: The AWD system is temporarily dis-
abled due to overload condition. When the appropriate conditions exist, the Electronic
Vehicle Information Center (EVIC) displays the following
ELECTRONIC VEHICLE INFORMATION CENTER messages.
(EVIC) — IF EQUIPPED 4
The Electronic Vehicle Information Center (EVIC) con- • LEFT/RIGHT TURN SIGNAL ON (with a continuous
sists of the following: warning chime)
• Vehicle information warning message displays • INVALID KEY & FOB (with a single chime)
• PROGRAM KEY & FOB • UNLOCK TO OPEN LIFTGATE (with a single chime)
• MEMORY #1/#2 POSITION SET (with a single chime) • PUT IN PARK FOR LIFTGATE (with a single chime)
• MEMORY #1/#2 POS SELECTED • TOO COLD FOR PWR LIFTGATE (with a single
chime)
• MEMORY SYSTEM DISABLED VEHICLE NOT IN
PARK (with a single chime) • TOO HOT FOR PWR LIFTGATE (with a single chime)
• SET INHIBITED DUE TO MOTION (with a single • PERFORM SERVICE (with a single chime)
chime)
• LEFT/RIGHT FRONT DOOR AJAR (one or more,
• FOB LINKED (with a single chime) with a single chime if speed is above 1 mph)
• FOB UNLINKED (with a single chime) • LEFT/RIGHT REAR DOOR AJAR (one or more, with
a single chime if speed is above 1 mph)
• PARK BRAKE ENGAGED (with a single chime)
• DOOR(S) AJAR (with a single chime)
• LOW BRAKE FLUID (with a single chime)
• DOOR(S) AND GATE AJAR (with a single chime)
• LOW FUEL (with a single chime)
• LIFT GATE AJAR (with a single chime if speed is
• MENU IN PARK ONLY
above 1 mph)
• LIST # ALERT MESSAGES
• WASHER FLUID LOW (with a single chime) • 1,2,3 OR 4 TIRE(S) LOW PRESSURE (Refer to ”Tire
Pressure Monitor System” in the “Starting And Oper-
• PEDAL ADJUST DISABLED CRUISE ENGAGED
ating, Tire Section”)
• PEDAL ADJUST DISABLED VEHICLE IN REVERSE
• SERVICE TIRE SYSTEM SOON (Refer to ”Tire Pres-
• CHANNEL 1, 2, OR 3 TRANSMIT (with a single sure Monitor System” in the “Starting And Operating,
chime) Tire Section”)
• CHANNEL 1, 2, OR 3 TRAINING (with a single • TCS SUSPENDED (Traction Control System, with a 4
chime) graphic and single chime)
• CHANNEL 1, 2, OR 3 TRAINED (with a single chime) • TCS ACTIVE (Traction Control System, with a
graphic)
• CLEARING CHANNELS
• SERVICE TCS SYSTEM (Traction Control System, with
• CHANNELS CLEARED
a graphic and single chime)
• CHANNELS DEFAULTED
• DID NOT TRAIN
Oil Change Required 2. Fully depress the accelerator pedal slowly three times
Your vehicle is equipped with an engine oil change within 10 seconds.
indicator system. The “Oil Change Required” message
3. Turn the ignition switch to the “LOCK” position.
will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the NOTE: If the indicator message illuminates when you
next scheduled oil change interval. The engine oil change start the vehicle, the oil change indicator system did not
indicator system is duty cycle based, which means the reset. If necessary repeat this procedure.
engine oil change interval may fluctuate dependent upon
NOTE:
your personal driving style.
• The oil change indicator system will not monitor the
Unless reset, this message will continue to display each time since the last oil change. Change the engine oil if
time you turn the ignition switch to the ON/RUN it has been 6 months since your last oil change even if
position. To turn off the message temporarily, press and the oil change indicator message is NOT illuminated.
release the Menu button. To reset the oil change indicator
• Change the engine oil more often if you drive your
system (after performing the scheduled maintenance)
vehicle off-road for an extended period.
perform the following procedure:
• Under no circumstances should oil change intervals
1. Turn the ignition switch to the “ON” position (Do not
exceed 6,000 miles (10,000 km) or 6 months, whichever
start the engine).
comes first.
Customer Programmable Features — If Equipped ASSIST DISABLED after the feature has been disabled
Press the MENU button until one of the following and SERVICE PARK ASSIST SYSTEM if there is a prob-
display choices appears: lem with the system.
Language? Service Interval
When in this display you may select one of three lan- When this feature is selected a service interval between
guages for all display nomenclature, including the trip 2,000 miles (3 200 km) and 6, 000 miles (10 000 km) in 500
computer functions and navigation system. Press the mile (800 km) increments may be selected. Pressing the 4
STEP button while in this display selects English, STEP button when in this display will select distances
Francais, or Espanol. As you continue the displayed between 2,000 miles (3 200 km) and 6, 000 miles (10 000
information will be shown in the selected language. km) in 500 mile (800 km) increments.
Park Assist System? ON/OFF Reset Service Distance (Displays Only if Service
When this feature is selected the system scans for objects Interval was Changed)
behind the vehicle using four sensors located in the rear When this feature is selected the current accumulated
bumper. Objects can be detected from up to 59 inches service distance can be reset to the newly selected service
(150 cm). Pressing the “STEP” button while in this interval. Pressing the STEP button when in this display
display will disable/enable the Rear Park Assist System. will select “Yes” or “No.”
The EVIC will display the following message: PARK
turn off when the wipers are turned off if they were The Easy Entry Easy Exit feature is not enabled when the
turned on in this way. Pressing the STEP button when in vehicle is delivered from the factory. The Easy Entry Easy
this display will select “Yes” or “No.” Exit feature is enabled (or later disabled) through the
programmable features in the Electronic Vehicle Informa-
NOTE: Turning the headlights on during the daytime
tion Center (EVIC). Pressing the STEP button when in
causes the instrument panel lights to dim. To increase the
this display will select “Yes” or “No.” The seat will return
brightness, refer to “Lights” in this section.
to the memorized seat location (if REMOTE LINK TO
Power Accessory Delay? MEMORY is set to YES) when the remote keyless entry
When this feature is selected, the power window transmitter is used to unlock the door. For more informa-
switches, radio, hands–free system, DVD video system, tion refer to “Easy Entry/Exit Seat in the Driver Memory
power sunroof, and power outlets will remain active for Seat section.
up to 45 seconds after the ignition switch has been turned
Display U.S. or Metric?
off. Opening a vehicle door or liftgate will cancel this
Pressing the US/M button will change the EVIC, odom-
feature.
eter, navigation system and A/C Control units from US
Easy Exit Seat? (Available with Memory Seat Only) to Metric.
This feature provides automatic driver’s seat positioning
which will enhance driver mobility out of and into the
vehicle.
Compass Display — If Equipped To put into a Calibration Mode: Turn on the ignition
This display provides one of eight compass readings to switch and set the display to Compass. Press the RESET
indicate the direction the vehicle is facing. button for at least 10 seconds until the “COMPASS
CALIBRATING” message appears. Release the MENU
Automatic Compass Calibration
button and drive the vehicle in one or more complete
This compass is self-calibrating which eliminates the
three, 360° circles, under 5 mph (8 km/h) in an area free
need to manually calibrate the compass. When the ve-
from large metal objects, until the “COMPASS CALI-
hicle is new, the compass may appear erratic and the 4
BRATING” message turns off.
EVIC will display “COMPASS CALIBRATING” until the
compass is calibrated. The compass will function nor- Compass Variance
mally. Compass Variance is the difference between magnetic
North and Geographic North. In some areas of the
To calibrate the compass, drive the vehicle in one or more
country, the difference between magnetic and geographic
complete 360° circles, under 5 mph (8 km/h) in an area
North is great enough to cause the compass to give false
free from large metal objects, until the “COMPASS CALI-
readings. In order to ensure accuracy, the compass vari-
BRATING” message turns off.
ance should be properly set according to the compass
Manual Compass Calibration variance zone that the vehicle is in.
If the compass appears erratic, inaccurate or abnormal,
you may wish to manually calibrate the compass. Prior to
calibration, make sure the proper zone is selected.
NOTE: Magnetic materials should be kept away from To set the variance: Turn the ignition switch ON and set
the overhead console. the display to Compass. Press the MENU button for
approximately 5 seconds but no more than 10 seconds.
The “COMPASS VARIANCE” message and the last vari-
ance zone number will be displayed. Press the STEP
button to select the proper variance zone as shown in the
map. Press the RESET button to set the new variance
zone and resume normal operation.
Mini-Trip Functions — If Equipped
This displays information on the following:
• Average Fuel Economy (ECO AVG)
Shows the average fuel economy since the last reset. The
minimum average fuel economy that will be displayed
on reset is 0.3 mpg.
• Distance To Empty (DTE)
Shows the estimated distance that can be travelled with
the fuel remaining in the tank. This estimated distance is
determined using the MPG for the last few minutes.
On vehicles equipped with an Analog Clock the radio Clock Setting Procedure
time display will function as follows:
1. Turn the ignition switch to the ON or ACC position
• Radio On — Radio clock will display for approxi- and press the time button. Using the tip of a ballpoint pen
mately 5 seconds after button is pressed, then default or similar object, press either the hour (H) or minute (M)
back to radio frequency. buttons on the radio.
• Radio Off — Radio clock will display for approxi- 2. Press the H button to set hours or the M button to set
mately 5 seconds after button is pressed, then default minutes. The time setting will increase each time you
back to blank screen. press a button.
The following radio time options can be changed by your RADIO GENERAL INFORMATION
dealer service department:
Radio Broadcast Signals
• Radio On — Radio clock will continue to be displayed Your new radio will provide excellent reception under
after button is pressed. most operating conditions. Like any system, however, car
• Radio Off — Radio clock will displayed continuously. radios have performance limitations, due to mobile op-
eration and natural phenomena, which might lead you to
believe your sound system is malfunctioning. To help
you understand and save you concern about these “ap- AM Reception
parent” malfunctions, you must understand a point or AM sound is based on wave amplitude, so AM reception
two about the transmission and reception of radio sig- can be disrupted by such things as lightning, power lines
nals. and neon signs.
Two Types of Signals FM Reception
There are two basic types of radio signals... AM or Because FM transmission is based on frequency varia-
Amplitude Modulation, in which the transmitted sound tions, interference that consists of amplitude variations 4
causes the amplitude, or height, of the radio waves to can be filtered out, leaving the reception relatively clear,
vary... and FM or Frequency Modulation, in which the which is the major feature of FM radio.
frequency of the wave is varied to carry the sound.
NOTE: The radio, steering wheel radio controls (if
Electrical Disturbances equipped), and 6 disc CD/DVD changer (if equipped)
Radio waves may pick up electrical disturbances during will remain active for up to 90 seconds after the ignition
transmission. They mainly affect the wave amplitude, switch has been turned off, depending upon the acces-
and thus remain a part of the AM reception. They sory delay setting. Opening a vehicle front door will
interfere very little with the frequency variations that cancel this feature.
carry the FM signal.
RAH radio
Toggle the TUNE button to select the following format types: Program Type Radio Display
Program Type Radio Display Religious Talk Religious Talk
Adult Hits Adult Hit Rock Rock
Classical Classical Soft Soft
Classic Rock Classic Rock Soft Rock Soft Rock
College College Soft Rhythm and Blues Soft R&B
Country Country Sports Sports 4
Information Inform Talk Talk
Jazz Jazz Top 40 Top 40
Foreign Language Language Weather Weather
News News By pressing the SEEK button when the PTY icon is
Nostalgia Nostalgia displayed, the radio will be tuned to the next frequency
Oldies Oldies station with the same selected PTY name. The PTY
Personality Personality function only operates when in the FM and Satellite (if
Public Public equipped) modes.
Rhythm and Blues R&B The radio display will flash “SEEK” and the selected PTY
Religious Music Religious Music program type when searching for the next PTY station. If
no station is found with the selected PTY program type, make another selection. Holding the button in will by-
the radio will return to the last preset station. pass stations without stopping until you release it.
If a preset button is activated while in the PTY (Program Tuning
Type) mode, the PTY mode will be exited and the radio Press the TUNE control up or down to increase or
will tune to the preset station. decrease the frequency. If you press and hold the button,
the radio will continue to tune until you release the
Mode
button. The frequency will be displayed and continu-
Press the MODE button to select between, AM, FM, CD,
ously updated while the button is pressed.
CD/DVD changer or the Satellite Radio (if equipped).
When the Satellite Radio (if equipped) is selected “SA” Balance
will appear in your radio display. The Balance control adjusts the left-to-right speaker bal-
ance. Press the AUDIO button, select BALANCE, then
A disc may remain in the radio while in the Satellite or
press SEEK + or SEEK 2 to adjust the balance.
radio mode.
Fade
Seek
The Fade control provides for balance between the front
Press and release the SEEK button to search for the next
and rear speakers. Press the AUDIO button, select FADE,
station in either the AM, FM or Satellite mode. Press the
then press SEEK + or SEEK 2 to adjust the fade balance.
top of the button to seek up and the bottom to seek down.
The radio will remain tuned to the new station until you
NOTE: Changes or modifications not expressively ap- Inserting The Compact Disc
proved by the party responsible for compliance could
void the user’s authority to operate the equipment. CAUTION!
CD Player Operation This CD player will accept only 4–3/4 inch (12 cm)
NOTE: discs only. The use of other sized discs may damage
• The ignition switch must be in the ON or ACC the CD player mechanism.
position and the volume control ON before the CD
player will operate.
You may either insert or eject a disc with the radio OFF.
• This Radio is capable of playing compact discs (CD),
recordable compact discs (CD-R), rewritable compact If you insert a disc with the ignition ON and the radio
discs (CD-RW) compact discs with MP3 tracks and OFF, the display will show the time of day. If you insert
multisession compact discs with CD and MP3 tracks. a disc with the ignition OFF, the display will show the
time of day for about 5 seconds, then go out.
If the power is ON, the unit will switch from radio to CD
mode and begin to play when you insert the disc. The
display will show the track number and index time in
minutes and seconds. Play will begin at the start of track
one.
CD/DVD Changer Operation When reading discs recorded using formats other than
Press the MODE button to select between the CD player ISO 9660 Level 1 and Level 2, the radio may fail to read
and the optional remote CD/DVD changer. files properly and may be unable to play the file nor-
mally. UDF and Apple HFS formats are not supported.
Time
Press the TIME button to change the display from The radio uses the following limits for file systems:
elapsed CD or DVD playing time to time of day.
• Maximum number of directory levels: 15
Notes On Playing MP3 Files
• Maximum number of files: 255
The radio can play MP3 files, however, acceptable MP3
file recording media and formats are limited. When • Maximum number of folders: 100
writing MP3 files, pay attention to the following restric-
• Maximum number of characters in file/folder names:
tions.
• Level 1: 12 (including a separator 9.9 and a 3
Supported media (disc types)
character extension)
The MP3 file recording media supported by the radio are
CD-ROM, CD-R and CD-RW. • Level 2: 31 (including a separator 9.9 and a 3
character extension)
Supported medium formats (file systems)
The medium formats supported by the radio are ISO 9660 Multisession disc formats are supported by the radio.
Level 1 and Level 2 and includes the Joliet extension. Multisession discs may contain combinations of normal
CD audio tracks and computer files (including MP3 files). MPEG Sampling Fre-
Discs created with an option such as 9keep disc open after Bit rate (kbps)
Specification quency (kHz)
writing9 are most likely multisession discs. The use of 320, 256, 224,
multisession for CD audio or MP3 playback may result in MPEG-1 Audio 192, 160, 128,
longer disc loading times. 48, 44.1, 32
Layer 3 112, 96, 80, 64,
56, 48, 40, 32
Supported MP3 file formats
The radio will recognize only files with the *.mp3 exten- 160, 128, 144,
MPEG-2 Audio 112, 96, 80, 64, 4
sion as MP3 files. Non-MP3 files named with the *.mp3 24, 22.05, 16
Layer 3 56, 48, 40, 32, 24,
extension may cause playback problems. The radio is
16, 8
designed to recognize the file as an invalid MP3 and will
not play the file. ID3 Tag information for artist, song title and album title
are supported for version 1 ID3 tags. ID3 version 2 is not
When using the MP3 encoder to compress audio data to supported by the radios.
an MP3 file, the bit rate and sampling frequencies in the
following table are supported. In addition, variable bit Playlist files are not supported. MP3 Pro files are not
rates (VBR) are also supported. The majority of MP3 files supported.
use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or
VBR bit rates.
Playback of MP3 files Operation Instructions - (CD Mode For MP3 Audio
When a medium containing MP3 data is loaded, the Play)
radio checks all files on the medium. If the medium
SEEK Button (CD Mode For MP3 Play)
contains a lot of folders or files, the radio will take more
Pressing the SEEK + button plays the next MP3 File.
time to start playing the MP3 files.
Pressing the SEEK 2 button plays the beginning of the
Loading times for playback of MP3 files may be affected MP3 file. Pressing the button within the first ten seconds
by the following: plays the previous file.
• Media - CD-RW media may take longer to load than INFO Button (CD Mode For MP3 Play)
CD-R media Press and INFO button while playing MP3 disc. The
radio scrolls through the following TAG information:
• Medium formats - Multisession discs may take longer
Song Title, Artist, File Name, and Folder Name (if avail-
to load than non-multisession discs
able).
• Number of files and folders - Loading times will
Press the INFO button once more to return to 9elapsed
increase with more files and folders
time9 priority mode.
To increase the speed of disc loading, it is recommended
to use CD-R media and single-session discs. To create a
single-session disc, enable the Disc at Once option before
writing to the disc.
RW/FF (CD Mode For MP3 Play) Operating Instructions - Hands Free Phone (If
Press the FF side of the button to move forward through Equipped)
the MP3 selection. Press the RW side of the button to Refer to Hands Free Phone section of the Owner’s
move back through the MP3 selection. Manual.
AM/FM Button (CD Mode For MP3 Play) Operating Instructions - Satellite Radio Mode (If
Switches back to Radio mode. Equipped)
Refer to the Satellite Radio section of the Owner’s 4
RND Button (CD Mode For MP3 Play)
Manual.
Pressing this button plays files randomly.
Operating Instructions - Video Entertainment
DIR Button (CD Mode For MP3 Play)
System (VESt) (If Equipped)
Press the DIR Button to display folders, when playing an
Refer to 6 Disc CD/DVD Changer (RDV) section of the
MP3 discs that have a file/folder structure. Press DISC
Owner’s Manual.
up (button 1) or DISC down (button 5) to move through
the folders. Press the SET button to select a folder.
REV Radio
Toggle the TUNE button to select the following format types: Program Type Radio Display
Program Type Radio Display Religious Talk Religious Talk
Adult Hits Adult Hit Rock Rock
Classical Classical Soft Soft
Classic Rock Classic Rock Soft Rock Soft Rock
College College Soft Rhythm and Blues Soft R & B
Country Country Sports Sports 4
Information Inform Talk Talk
Jazz Jazz Top 40 Top 40
Foreign Language Language Weather Weather
News News By pressing the SEEK button when the PTY icon is
Nostalgia Nostalgia displayed, the radio will be tuned to the next frequency
Oldies Oldies station with the same selected PTY name. The PTY
Personality Personality function only operates when in the FM and Satellite (if
Public Public equipped) modes.
Rhythm and Blues R&B The radio display will flash “SEEK” and the selected PTY
Religious Music Religious Music program type when searching for the next PTY station. If
no station is found with the selected PTY program type, make another selection. Holding the button in will by-
the radio will return to the last preset station. pass stations without stopping until you release it.
If a preset button is activated while in the PTY (Program Tuning
Type) mode, the PTY mode will be exited and the radio Press the TUNE control up or down to increase or
will tune to the preset station. decrease the frequency. If you press and hold the button,
the radio will continue to tune until you release the
Mode
button. The frequency will be displayed and continu-
Press the MODE button to select between, AM, FM, CD,
ously updated while the button is pressed.
CD/DVD changer or the Satellite Radio (if equipped).
When the Satellite Radio (if equipped) is selected “SA” Balance
will appear in your radio display. The Balance control adjusts the left-to-right speaker bal-
ance. Press the AUDIO button, select BALANCE, then
A disc may remain in the radio while in the Satellite or
press SEEK + or SEEK 2 to adjust the balance.
radio mode.
Fade
Seek
The Fade control provides for balance between the front
Press and release the SEEK button to search for the next
and rear speakers. Press the AUDIO button, select FADE,
station in either the AM, FM or Satellite mode. Press the
then press SEEK + or SEEK 2 to adjust the fade balance.
top of the button to seek up and the bottom to seek down.
The radio will remain tuned to the new station until you
NOTE: Changes or modifications not expressively ap- Inserting The Compact Disc
proved by the party responsible for compliance could
void the user’s authority to operate the equipment. CAUTION!
CD Player Operation This CD player will accept only 4–3/4 inch (12 cm)
NOTE: discs only. The use of other sized discs may damage
• The ignition switch must be in the ON or ACC the CD player mechanism.
position and the volume control ON before the CD
player will operate.
You may either insert or eject a disc with the radio OFF.
• This Radio is capable of playing compact discs (CD),
recordable compact discs (CD-R), rewritable compact If you insert a disc with the ignition ON and the radio
discs (CD-RW) compact discs with MP3 tracks and OFF, the display will show the time of day. If you insert
multi-session compact discs with CD and MP3 tracks. a disc with the ignition OFF, the display will show the
time of day for about 5 seconds, then go out.
If the power is ON, the unit will switch from radio to CD
mode and begin to play when you insert the disc. The
display will show the track number and index time in
minutes and seconds. Play will begin at the start of track
one.
CD/DVD Changer Operation When reading discs recorded using formats other than
Press the MODE button to select between the CD player ISO 9660 Level 1 and Level 2, the radio may fail to read
and the optional remote CD/DVD changer. files properly and may be unable to play the file nor-
mally. UDF and Apple HFS formats are not supported.
Time
Press the TIME button to change the display from The radio uses the following limits for file systems:
elapsed CD or DVD playing time to time of day.
• Maximum number of directory levels: 15
Notes On Playing MP3 Files
• Maximum number of files: 255
The radio can play MP3 files, however, acceptable MP3
file recording media and formats are limited. When • Maximum number of folders: 100
writing MP3 files, pay attention to the following restric-
• Maximum number of characters in file/folder names:
tions.
• Level 1: 12 (including a separator 9.9 and a 3
Supported media (disc types)
character extension)
The MP3 file recording media supported by the radio are
CD-ROM, CD-R and CD-RW. • Level 2: 31 (including a separator 9.9 and a 3
character extension)
Supported medium formats (file systems)
The medium formats supported by the radio are ISO 9660 Multi-session disc formats are supported by the radio.
Level 1 and Level 2 and includes the Joliet extension. Multi-session discs may contain combinations of normal
CD audio tracks and computer files (including MP3 files). MPEG Sampling Fre-
Discs created with an option such as 9keep disc open after Bit rate (kbps)
Specification quency (kHz)
writing9 are most likely multi-session discs. The use of 320, 256, 224,
multi-session for CD audio or MP3 playback may result MPEG-1 Audio 192, 160, 128,
in longer disc loading times. 48, 44.1, 32
Layer 3 112, 96, 80, 64,
56, 48, 40, 32
Supported MP3 file formats
The radio will recognize only files with the *.mp3 exten- 160, 128, 144,
MPEG-2 Audio 112, 96, 80, 64, 4
sion as MP3 files. Non-MP3 files named with the *.mp3 24, 22.05, 16
Layer 3 56, 48, 40, 32, 24,
extension may cause playback problems. The radio is
16, 8
designed to recognize the file as an invalid MP3 and will
not play the file. ID3 Tag information for artist, song title and album title
are supported for version 1 ID3 tags. ID3 version 2 is not
When using the MP3 encoder to compress audio data to supported by the radios.
an MP3 file, the bit rate and sampling frequencies in the
following table are supported. In addition, variable bit Playlist files are not supported. MP3 Pro files are not
rates (VBR) are also supported. The majority of MP3 files supported.
use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or
VBR bit rates.
Playback of MP3 files Operation Instructions - (CD Mode For MP3 Audio
When a medium containing MP3 data is loaded, the Play)
radio checks all files on the medium. If the medium
SEEK Button (CD Mode For MP3 Play)
contains a lot of folders or files, the radio will take more
Pressing the SEEK + button plays the next MP3 File.
time to start playing the MP3 files.
Pressing the SEEK 2 button plays the beginning of the
Loading times for playback of MP3 files may be affected MP3 file. Pressing the button within the first ten seconds
by the following: plays the previous file.
• Media - CD-RW media may take longer to load than INFO Button (CD Mode For MP3 Play)
CD-R media Press and INFO button while playing MP3 disc. The
radio scrolls through the following TAG information:
• Medium formats - Multi-session discs may take longer
Song Title, Artist, File Name, and Folder Name (if avail-
to load than not multi-session discs
able).
• Number of files and folders - Loading times will
Press the INFO button once more to return to 9elapsed
increase with more files and folders
time9 priority mode.
To increase the speed of disc loading, it is recommended
to use CD-R media and single-session discs. To create a
single-session disc, enable the Disc at Once option before
writing to the disc.
RW/FF (CD Mode For MP3 Play) Operating Instructions - Satellite Radio Mode (If
Press the FF side of the button to move forward through Equipped)
the MP3 selection. Press the RW side of the button to Refer to the Satellite Radio section of the Owner’s
move back through the MP3 selection. Manual.
AM/FM Button (CD Mode For MP3 Play) Operating Instructions — MP3 Player, Portable
Switches back to Radio mode. Walkman
An MP3 player can be connected to the audio system. 4
RND Button (CD Mode For MP3 Play)
Connect the cables to the RCA jacks located on the front
Pressing this button plays files randomly.
of the CD/DVD changer.
DIR Button (CD Mode For MP3 Play)
NOTE: Follow the manufactures instructions for the
Press the DIR Button to display folders, when playing an
correct colors when connecting the RCA cables. (Refer to
MP3 discs that have a file/folder structure. Press DISC
the illustration below).
up (button 1) or DISC down (button 5) to move through
the folders. Press the SET button to select a folder. Operating Instructions — Video
Games/Camcorders
Operating Instructions - Hands Free Phone (If
A video game unit or camcorder can be connected to the
Equipped)
rear audio/video system. Connect the cables to the RCA
Refer to Hands Free Phone section of the Owner’s
jacks located on the front of the CD/DVD changer.
Manual.
NOTE: To operate a video game unit a DC to AC 6 DISC CD/DVD CHANGER (RDV) — IF EQUIPPED
adapter may be required, plug the adapter into any The Rear Seat Audio/Video System allows passengers to
power outlet. listen to a CD or DVD from the 6 disc CD/DVD changer
through wireless headphones, while the front seat pas-
Listed below is the standard RCA
sengers listen to either AM/FM, Cassette or CDs from the
Jack/Cable connection. You may also
radio speakers. A remote control is provided for func-
want to refer to the manufacture’s
tions such as changing tracks or DVD functions, as well
instructions for the correct colors
as selecting discs loaded in the 6 disc CD/DVD changer
when connecting the RCA cables.
while listening to the Rear Audio/Video System.
The Rear Seat Audio/Video System may be available in a
1. Video in (yellow) base and premium version. The premium version in-
cludes a six disc changer, remote control and two sets of
2. Left audio in (white)
wireless headphones. The base version includes a single
3. Right audio in (red) disc player and remote control.
NOTE: MP3 player’s, video game systems, camcorders The CD/DVD Changer will play CD-R, CD-RW, CD-
connected to the RCA jacks and CD’s or DVD’s inserted Audio and DVD Video disc formats. The video screen
into the radio, can be heard through the headphones or will turn on automatically once a DVD is inserted into the
the cabin when AUX Mode is selected. changer.
NOTE: The ignition switch must be in the ON or ACC Operating Instructions — CD/DVD Changer
position before the CD/DVD changer will operate.
Loading The CD/DVD Changer
The premium version has a multi-disc changer,
and will accept up to six discs. The base
version is a single-disc player, and will only
accept one disc.
To insert disc(s) into the changer, follow the instructions 4
shown:
1. On vehicles equipped with the premium version,
select and press any numbered button without an illumi-
nated light above it.
2. Gently insert the disc with the label facing up while
Six Disc DVD Changer the light below the loading slot is illuminated. On
vehicles equipped with the premium version the light
above the chosen button will also be flashing, indicating
which numbered position the disc will be loaded into. play from the menu options. The radio display will show
The disc will automatically be pulled into the CD/DVD the chapter number and index time in hours and minutes
changer. of the DVD, or the track number, minutes and second of
the CD.
3. Upon insertion, the disc will begin to play, and the
light below the loading slot will turn off. On vehicles NOTE:
equipped with the premium version the light above the • You may eject a disc with the radio OFF.
chosen button will remain illuminated.
• If you insert a disc with the ignition ON and the radio
4. Repeat the process for loading any additional CD/ OFF, the DVD will automatically be pulled into the
DVDs into the premium version multi-disc changer. The DVD changer and the display will show the time of
CD/DVD changer will stop while additional CD/DVDs day.
are loaded.
• It is recommended to label home made burned discs
If the radio volume control is ON, the unit will switch with a permanent marker instead of adhesive labels.
from radio to CD/DVD mode and the video screen will These types of labels may become loose and cause the
turn on. If the DVD supports the autoplay feature, play disc to be stuck in the DVD player. This may cause
will begin automatically in approximately 10 seconds, permanent damage to the DVD mechanism.
after the DVD disc menu is displayed. If the DVD does
not play automatically, press the ENTER button on the
remote control or on the side of the video screen to select
Remote Control
This button changes between available modes and can be NEXT/PREV Buttons (2, 15)
heard in the headphones. Press the up arrow or the NEXT button for the next
chapter or track on the disc. Press the down arrow or
PROG UP/DOWN Buttons (10, 11)
PREV button to return to the beginning of the current
PROG UP selects the next disc loaded in the changer.
chapter or track. Press the down arrow or PREV button
PROG DOWN selects the previous disc loaded in the
twice within two seconds to return to the previous
changer.
chapter or track. Each press of the NEXT/PREV button
SLOW Button (12) up or down will toggle through the chapters or tracks.
This button only functions in DVD video mode. Press this
FF/RW Buttons (3, 16)
button to advance the video. If the DVD is paused,
Press and hold FF (Fast Forward) once and the CD/DVD
pressing this button will advance the video frame by
changer will begin to fast forward until the FF button is
frame.
released. The RW (Reverse) button works in a similar
STOP Button (13) manner.
This button only functions in DVD video mode. Press this
ENTER Button (17)
button to stop the DVD.
This button only functions in DVD video mode. Use the
MENU Button (14) ENTER button to enter selections from the menu screens.
This button only functions in DVD video mode. Press this Use the arrow buttons to toggle through the menu screen
button to select the DVD disc menu. options.
2. Enter Button
This button will enter the selection from the
on-screen menu.
3. Brightness Button
Changes the brightness of the screen picture.
Video Screen and Controls
DOWN (-) will page down until the first four digits are Selecting Satellite Mode in RBP, RBU, RAZ, RB1
displayed. The radio will exit the ESN/SID mode when and RBQ Radios
any other button is pushed, the ignition is turned OFF, or Press the MODE button repeatedly until the word
5 minutes has passed since any button was pushed. 9SIRIUS9 appears in the display. These radios will also
display the following:
ESN/SID Access With RBP, RBU, RAZ, RB1 and
RBQ Radios • After 3 seconds, the current channel name and channel
With the ignition switch in the ACCESSORY position and number will be displayed for 5 seconds.
the radio OFF, press the CD Eject and TIME buttons
• The current program type and channel number will
simultaneously for 3 seconds. All twelve ESN/SID num-
then be displayed for 5 seconds.
bers will be displayed. The radio will exit the ESN/SID
mode when any other button is pushed, the ignition is • The current channel number will then be displayed
turned OFF, or 5 minutes has passed since any button until an action occurs.
was pushed.
A CD or tape may remain in the radio while in the
Selecting Satellite Mode in RBB, RAH, REV and Satellite radio mode.
RBK Radios
Press the MODE button repeatedly until 9S A9 appears in
the display. A CD or tape may remain in the radio while
in the Satellite radio mode.
Manual Air Conditioning and Heating System second time the indicator light turns off, the blower will
turn off and the system will be positioned in the recircu-
lation mode.
Blower Control
The Blower controls the amount of air delivered to
the passenger compartment. There are four blower
speeds. 4
The fan speed increases as you
move the control clockwise.
Panel Mode Air comes from the outlets in the instrument panel. Each
of these outlets can be individually adjusted to direct the
flow of air. Moving the air vane knob on the center
outlets down, will close off the air flow from the center
outlets. The thumbwheel next to the outboard outlets can
be rotated to regulate or shut off the air flow from these
outlets.
4
Panel Outlets
Bi-Level Mode Air comes from both the instrument panel outlets, floor
outlets and defrost. A slight amount of air is also directed
through the side window demister outlets.
NOTE: In many temperature lever positions, the bi-
level mode is designed to provide cooler air out of the
panel outlets and warmer air from the floor outlets.
Bi-Level Outlets
• If the recirculation button is pressed while in the Mix • Turn the ignition switch to the OFF position.
or Defrost mode, the indicator light in the recirculation
• Set the mode control to “PANEL”.
button will flash 3 times indicating that recirculation is
not allowed. • Depress and hold in the “POWER” button.
A/C Recirculation Programming • Start the engine, and continue to hold in the “POWER”
The recirculation control is programmed to cancel the button until the indicator light starts flashing repeat-
recirculation mode when the ignition key is turned OFF edly.
and will reset to outside air mode when the ignition key
• Press the recirculation button until the indicator light
is turned ON. The frequent use of outside air will help
remains lit.
keep odors from building up within the air conditioner-
heater housing. It is recommended that the recirculation • The selection will be stored when the ignition switch is
mode be used as little as possible, especially in humid turned OFF or if the “POWER” button is pressed.
climates.
If the recirculation indicator light is lit, the recirculation
For hot and dry climates, or people who are allergic to mode will not reset when the engine is started. If the
pollen and find frequent use of the recirculation mode recirculation indicator light is not lit, the recirculation
necessary, the recirculation mode can be programmed to mode will reset to the outside air mode when the engine
not automatically reset to the outside mode by using the is started. The programmed status can be changed back
following procedures: and forth by following the above mentioned procedure.
temperature you would like the system to maintain. Refer to the “Electronic Vehicle Information Center-
When the system is set to your comfort level, it is not Customer Programmable Features” in Section 3 of this
necessary to change the settings. You will experience the manual.
greatest efficiency by allowing the system to function
To provide you with maximum comfort in the automatic
automatically. The system will operate fully automati-
mode, during cold start-ups the blower fan will remain
cally in either 9AUTO HI9 or 9AUTO LO9. The 9AUTO
off and “DELAY” will appear in the display until the
LO9 setting will limit the maximum fan speed and should
engine warms up. An estimate of the time remaining
be used when more quiet operation is desired. Use the
until the “DELAY” is complete will appear periodically
9AUTO HI9 setting when the quickest cool-down or
in the display. However, the fan will engage immediately
warm-up performance is desired.
if the defrost mode is selected or by pushing the blower
NOTE: switch and manually adjusting the fan speed.
• It is not necessary to move the temperature settings for
This feature may be disabled using the following proce-
cold or hot vehicles. The system automatically adjusts
dure:
the temperature, mode and fan speed to provide
comfort as quickly as possible. • Press and hold the Heated Rear Window and Auto LO
buttons for 5 seconds.
• The temperature can be displayed in U.S. or Metric by
selecting the US/M customer programmable feature. • The “DELAY” symbol will flash to indicate that the
feature as been disabled.
This feature may be enabled using the following proce- left and right side of the instrument panel. The outside
dure: temperature will replace the passenger’s temperature
setting in the display. Pressing the 9DUAL9 button a
• Press and hold the Heated Rear Window and Auto HI
second time or adjusting the passenger’s 9TEMP9 button
buttons for 5 seconds.
will return the system to dual independent temperature
• The “DELAY” symbol will flash to indicate that the operation.
feature as been enabled.
Manual Operation 4
Power Button This system offers a full complement of manual override
This button turns the entire system ON/OFF. When the features. The indicator light in both the 9AUTO HI9 or
system is turned on it will return to the previous settings. 9AUTO LO9 buttons will turn off when the system is
being used in the manual mode. The fan speed, airflow
Dual/Single Zone Operation
distribution, and outside air/recirculated air can be
When 9DUAL9 is displayed in the ATC control unit, the
manually adjusted.
driver and passenger air outlet temperatures can be
individually adjusted from the two independent 9TEMP9 NOTE: Each of these features operate independently
buttons. When a front seat passenger is not present, from each other. If any one feature is controlled manually,
pressing the 9DUAL9 button will match the passenger’s the remaining features will continue to operate automati-
temperature setting to the driver’s temperature setting. cally.
This will help equalize air outlet temperatures across the
Bi-Level Mode Air comes from both the instrument panel outlets and
floor outlets. A slight amount of air is also directed
through the defrost and side window demister outlets.
NOTE: In many temperature positions, the bi-level
mode is designed to provide cooler air out of the panel
outlets and warmer air from the floor outlets.
4
Bi-Level Outlets
windshield or side glass starts to impair visibility, press A/C Recirculation Programming
the front blower button and increase the fan speed to The recirculation control is programmed to cancel the
maximum. recirculation mode when the ignition key is turned OFF
and will reset to the outside air mode when the ignition
Recirculation Control
key is turned “ON”. The frequent use of outside air will
When the outside air contains smoke, odors,
help keep odors from building up within the air
high humidity, or if rapid cooling is desired
conditioner-heater housing. It is recommended that the
you may wish to recirculate interior air by
recirculation mode be used as little as possible, especially
pressing the recirculation button. The recircu-
in humid climates.
lation mode should only be used temporarily. The recir-
culate symbol will illuminate in the display when this For hot and dry climates, or people who are allergic to
button is selected. Push the button a second time to allow pollen and find frequent use of the recirculation mode
outside air into the vehicle. necessary, the recirculation mode can be programmed to
not automatically reset to the outside mode by using the
NOTE: In cold weather, use of the recirculation mode
following procedures:
may lead to excessive window fogging. The recirculation
mode is not allowed in the Mix and Defrost modes to • Turn the ignition switch to the OFF position.
improve window clearing operation. Recirculation will
• Press and hold the recirculation button.
be disabled automatically if these modes are selected.
• While holding the recirculation button, turn the igni- switch located in the center console between the second
tion switch to the “RUN” position. row seats. By pressing the 9REAR9 button a third time,
the rear fan will shut off.
• Continue holding the recirculation button for 4 sec-
onds, then release. When the ATC display reads 9REAR AUTO9 or when the
rear fan is off, the switch located in the center console
The recirculation control is now programmed so that the
between the second row seats is not functional. When the
recirculation mode will not reset to the outside air mode
ATC display reads 9REAR9, only the rear seat occupants 4
when the engine is restarted. The recirculation program-
can control the rear fan speed from the rear switch. When
ming can be changed back by repeating this procedure.
in the “REAR” mode, the rear occupants can set the rear
Rear Blower Operation switch to any fan speed including 9OFF9, or 9AUTO9.
To operate the rear fan, press the 9REAR9 button. The first While in the 9AUTO9 position, the rear fan speed will be
time this button is pressed the 9REAR AUTO9 display automatically controlled.
will illuminate indicating that the rear fan speed is
Summer Operation
automatically controlled. To manually control the rear
The engine cooling system in air conditioned vehicles
fan speed, press the 9REAR9 button again and only
must be protected with a high-quality antifreeze coolant
9REAR9 will illuminate in the display. This allows the rear
to provide proper corrosion protection and to protect
seat occupants to control the rear fan speed using the
against engine overheating. A 50% solution of ethylene
glycol antifreeze coolant in water is recommended. Refer system lubrication to minimize the possibility of com-
to section 7, Maintenance Procedures, of this manual for pressor damage when the system is started again.
proper coolant selection.
Window Fogging
Winter Operation Vehicle windows tend to fog on the inside in mild rainy
To insure the best possible heater and defroster perfor- or humid weather. To clear the windows, use the A/C
mance, make sure the engine cooling system is function- button to reduce the humidity inside the vehicle.
ing properly and the proper amount, type, and concen-
Fogging on the inside of the windshield can be quickly
tration of coolant is used. Refer to section 7, Maintenance
removed by pressing the defrost button and increasing
Procedures, of this manual for proper coolant selection.
the blower speed.
Use of the air Recirculation mode during winter months
is not recommended because it may cause window Do not use the Recirculation mode without the A/C
fogging. button for long periods as fogging may occur.
Vacation Storage Outside Air Intake
Anytime you store your vehicle, or keep it out of service Before driving, always make sure the air intake located
(i.e. vacation) for two weeks or more, run the air condi- directly in front of the windshield is free of obstructions
tioning system at idle for about five minutes in the fresh such as leaves, ice, or snow, which could reduce airflow
air and high blower setting. This will insure adequate and/or plug the water drain tube inside the plenum.
CONTENTS
m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 275 m Automatic Transmission . . . . . . . . . . . . . . . . . . 278
▫ Automatic Transmission . . . . . . . . . . . . . . . . 276 ▫ Brake/Transmission Interlock System . . . . . . . 279
▫ Normal Starting (Above 32°F / 0°C) . . . . . . . . 276 ▫ Automatic Transmission Ignition Interlock
5
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
▫ Extremely Cold Weather Starting (Below 220°F /
–29°C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276 ▫ Reset Mode - Electronic Transmission . . . . . . . 280
▫ High Altitude Starting (Above 4,000 Ft. / m AutoStick . . . . . . . . . . . . . . . . . . . . . . . . . . . . 282
1 219 m) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
▫ AutoStickt Operation . . . . . . . . . . . . . . . . . . 282
▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 277
▫ AutoStickt General Information . . . . . . . . . . . 282
▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . . 278
m All Wheel Drive — If Equipped . . . . . . . . . . . . 284
m Engine Block Heater — If Equipped . . . . . . . . . 278
STARTING PROCEDURES
WARNING!
Before starting your vehicle, adjust your seat, adjust both
inside and outside mirrors, and fasten your seat belts. • Be sure to turn off the engine and remove the
key from the ignition switch if you want to rest
or sleep in your car. Accidents can be caused by
inadvertently moving the gear selection lever or
by pressing the accelerator pedal. This may
cause excessive heat in the exhaust system, re-
sulting in overheating and vehicle fire which
may cause serious or fatal injuries.
• NEVER leave children alone in a vehicle. Leaving
5
children in a vehicle unattended is dangerous for a
number of reasons. A child or others could be
seriously or fatally injured. Don’t leave the keys in
the ignition. A child could operate power win-
dows, other controls, or move the vehicle
• Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build up
may cause serious injury or death.
Never pour fuel or other flammable liquid into the If the engine has been flooded, it may start to run, but not
throttle body air inlet opening in an attempt to start have enough power to continue running when the key is
the vehicle. This could result in flash fire causing
serious personal injury.
released. If this occurs, continue cranking with the accel- The engine block heater cord is routed under the hood on
erator pedal pushed all the way to the floor. Release the the driver side of the vehicle. It has a removable cap that
accelerator pedal and the key once the engine is running is located on the driver side of the Integrated Power
smoothly. Module.
If the engine shows no sign of starting after two 15
WARNING!
second periods of cranking with the accelerator pedal
held to the floor, the “Normal Starting” procedure should Remember to disconnect the cord before driving.
be repeated. Damage to the 110-115 volt electrical cord could cause
After Starting electrocution.
The idle speed will automatically decrease as the engine
warms up.
AUTOMATIC TRANSMISSION
ENGINE BLOCK HEATER — IF EQUIPPED The electronically controlled transmission provides a
The engine block heater warms engine coolant and precise shift schedule. The transmission electronics are
permits quicker starts in cold weather. Connect the cord self-calibrating; therefore, the first few shifts on a new
to a standard 110-115 volt AC electrical outlet with a vehicle, may be somewhat abrupt. This is a normal
grounded, three-wire extension cord. condition, and precision shifts will develop within a few
hundred miles.
CAUTION! WARNING!
Damage to the transmission may occur if the follow- It is dangerous to shift the selector lever out of “P” or
ing precautions are not observed: “N” if the engine speed is higher than idle speed. If
• Shift into PARK only after the vehicle has come to your foot is not firmly on the brake pedal, the vehicle
a complete stop. could accelerate quickly forward or in reverse. You
could lose control of the vehicle and hit someone or
• Shift into or out of REVERSE only after the something. Only shift into gear when the engine is
vehicle has come to a complete stop and the engine idling normally and when your right foot is firmly on
is at idle speed. the brake pedal.
5
• Do not shift from REVERSE, PARK, or NEUTRAL
into any forward gear when the engine is above
idle speed. Brake/Transmission Interlock System
This system prevents you from moving the gear shift out
• Before shifting into any gear, make sure your foot of PARK and into any gear unless the brake pedal is
is firmly on the brake pedal. pressed. This system is active only while the ignition
switch is in the ACCESSORY or ON position. Always
depress the brake pedal first, before moving the gear
selector out of PARK.
Automatic Transmission Ignition Interlock System right corner of the shifter bezel ring. While the override is
This system prevents the key from being removed unless pressed, the shifter can be moved out of the park position
the shift lever is in PARK. It also prevents shifting out of without pressing the brake. After operation return the
PARK unless the key is in the ACCESSORY or ON shifter bezel ring to its original position.
position.
NOTE: If a malfunction occurs, the system will trap the
key in the ignition cylinder to warn you that this safety
feature is inoperable. The engine can be started and
stopped but the key cannot be removed until you obtain
service.
Reset Mode - Electronic Transmission
For electrical system malfunctions there is an override for
the interlock system. In order to override this system the
key must be in the ignition with the switch in the ACC or
ON positions. Pull up and rearward on the shifter bezel
ring. Brake Interlock Override
The override can be activated by pressing the pink- NOTE: Even if the transmission can be reset, it is
colored tab, which can be accessed through the lower recommended that you visit a dealer at your earliest
AutoStickT Operation • If a ratio other than 1st is selected, and the vehicle is
By placing the selector lever one shift-level below the 9D9 brought to a stop, the transaxle control logic will
position, it can be moved from side to side. This allows automatically select the 1st gear ratio.
the driver to select a higher or lower range of gears. • Starting out in second gear is helpful in snowy or icy
Moving the selector lever to the Left (-) triggers a conditions.
downshift and to the Right (+) an upshift. The gear
position will display in the instrument cluster on the • Avoid using speed control when Autostickt is engaged.
transaxle range indicator. • The transaxle will automatically shift up when maxi-
mum engine speed is reached while Autostickt is
engaged.
PARKING BRAKE
When the parking brake is applied with the ignition
switch on, the brake light in the instrument cluster will
turn on.
NOTE: This light only shows that the parking brake is
applied. It does not show the degree of brake application.
Before leaving the vehicle, make sure that the parking
brake is fully applied and place the gear selector in the
Park position. To release the parking brake, pull out on 5
the parking brake release located on the left side of the
instrument panel.
Parking Brake Release
When parking on a hill, it is important to set the parking
brake before placing the gear selector in Park, otherwise
the load on the transmission locking mechanism may
make it difficult to move the selector out of park. As an
The ABS light monitors the Anti-Lock Brake When the vehicle is driven over 7 mph (11 km/h), you
System. The light will come on when the may also hear a slight clicking sound as well as some
ignition switch is turned to the ON position related motor noises. These noises are the system per-
and may stay on for as long as four seconds. forming its self check cycle to ensure that the ABS system
is working properly. This self check occurs each time the
If the ABS light remains on or comes on while driving, it
vehicle is started and accelerated past 7 mph (11 km/h).
indicates that the Anti-Lock portion of the brake system
is not functioning and that service is required. However, ABS is activated during braking under certain road or
the conventional brake system will continue to operate stopping conditions. ABS-inducing conditions can in-
normally if the BRAKE warning light is not on. clude ice, snow, gravel, bumps, railroad tracks, loose 5
debris, or panic stops.
If the ABS light is on, the brake system should be serviced
as soon as possible to restore the benefits of Anti-Lock You also may experience the following when the brake
brakes. If the ABS light does not come on when the system goes into Anti-lock:
Ignition switch is turned to the ON position, have the
• The ABS motor running (it may continue to run for a
bulb repaired as soon as possible.
short time after the stop),
If both the Brake Warning Light and the ABS Light
• the clicking sound of solenoid valves,
remain on, the Anti-Lock brakes (ABS) and Electronic
Brake Force Distribution (EBD) systems are not function- • brake pedal pulsations,
ing. Immediate repair to the ABS system is required.
• and a slight drop or fall away of the brake pedal at the POWER STEERING
end of the stop. The standard power steering system will give you good
vehicle response and increased ease of maneuverability
These are all normal characteristics of ABS.
in tight spaces. The system will provide mechanical
steering capability if power assist is lost.
WARNING!
If for some reason the power assist is interrupted, it will
The Anti-Lock Brake System contains sophisticated still be possible to steer your vehicle. Under these condi-
electronic equipment that may be susceptible to tions, you will observe a substantial increase in steering
interference caused by improperly installed or high effort, especially at very low vehicle speeds and during
output radio transmitting equipment. This interfer- parking maneuvers.
ence can cause possible loss of anti-lock braking
capability. Installation of such equipment should be NOTE: Increased noise levels at the end of the steering
performed by qualified professionals. wheel travel are considered normal and do not indicate
that there is a problem with the power steering system.
Upon initial start-up in cold weather, the power steering
All vehicle wheels and tires must be the same size and pump may make noise for a short amount of time. This is
type and tires must be properly inflated to produce due to the cold, thick fluid in the steering system. This
accurate signals for the computer. noise should be considered normal, and it does not in any
way damage the steering system.
• European Metric tire sizing is based on European • Temporary Spare tires are high-pressure compact
design standards. Tires designed to this standard have spares designed for temporary emergency use only.
the tire size molded into the sidewall beginning with Tires designed to this standard have the letter “T”
the section width. The letter 9P9 is absent from this tire molded into the sidewall preceding the size designa-
size designation. Example: 215/65R15 96H tion. Example: T145/80D18 103M.
• LT (Light Truck)-Metric tire sizing is based on U.S. • High Flotation tire sizing is based on U.S. design
design standards. The size designation for LT-Metric standards and it begins with the tire diameter molded
tires is the same as for P-Metric tires except for the into the sidewall. Example: 31x10.5 R15 LT.
letters “LT” that are molded into the sidewall preced- 5
ing the size designation. Example: LT235/85R16.
EXAMPLE:
Service Description:
95 = Load Index
—A numerical code associated with the maximum load a tire can carry.
H = Speed Symbol
—A symbol indicating the range of speeds at which a tire can carry a load corresponding
to its load index under certain operating conditions.
—The maximum speed corresponding to the Speed Symbol should only be achieved un-
der specified operating conditions (i.e. tire pressure, vehicle loading, road conditions, and 5
posted speed limits).
Load Identification:
(....blank....( = Absence of any text on sidewall of the tire indicates a Standard Load (SL) Tire
Extra Load (XL) = Extra Load (or Reinforced) Tire
Light Load = Light Load Tire
C,D,E = Load range associated with the maximum load a tire can carry at a specified pressure
Maximum Load — Maximum Load indicates the maximum load this tire is designed to carry.
Maximum Pressure — Maximum Pressure indicates the maximum permissible cold tire inflation pressure for this tire.
Tire Identification Number (TIN) located on the white sidewall side of the tire. Look for the
The TIN may be found on one or both sides of the tire; TIN on the outboard side of black sidewall tires as mounted
however, the date code may only be on one side. Tires with on the vehicle. If the TIN is not found on the outboard side
white sidewalls will have the full TIN including date code then you will find it on the inboard side of the tire.
EXAMPLE:
DOT MA L9 ABCD 0301
DOT = Department of Transportation
—This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire
safety standards, and is approved for highway use.
MA = Code representing the tire manufacturing location. (2 digits)
L9 = Code representing the tire size. (2 digits)
ABCD = Code used by tire manufacturer. (1 to 4 digits)
03 = Number representing the week in which the tire was manufactured. (2 digits)
—03 means the 3rd week.
01 = Number representing the year in which the tire was manufactured. (2 digits)
—01 means the year 2001.
—Prior to July 2000, tire manufacturers were only required to have 1 number to represent the year in
which the tire was manufactured. Example: 031 could represent the 3rd week of 1981 or 1991.
Tire Loading and Tire Pressure Tire and Loading Information Placard
Tire Placard Location
NOTE: The proper cold tire inflation pressure is listed
on either the face of the driver’s door or the driver’s side
“B” pillar.
5. Determine the combined weight of luggage and cargo NOTE: The following table shows examples on how to
being loaded on the vehicle. That weight may not safely calculate total load, cargo/luggage, and towing capaci-
exceed the available cargo and luggage load capacity ties of your vehicle with varying seating configurations
calculated in Step 4. and number and size of occupants. This table is for
illustration purposes only and may not be accurate for
6. If your vehicle will be towing a trailer, load from your
the seating and load carry capacity of your vehicle.
trailer will be transferred to your vehicle. Consult this
manual to determine how this reduces the available NOTE: For the following example, the combined weight
cargo and luggage load capacity of your vehicle. of occupants and cargo should never exceed 865 lbs. (392
kg). 5
1. Safety—
WARNING!
WARNING!
Overloading of your tires is dangerous. Overloading
can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can
increase your stopping distance. Use tires of the cause accidents.
recommended load capacity for your vehicle. Never • Under inflation increases tire flexing and can result
overload them. in tire failure.
• Over inflation reduces a tire’s ability to cushion
shock. Objects on the road and chuckholes can cause
TIRES — GENERAL INFORMATION
damage that result in tire failure. 5
• Unequal tire pressures can cause steering problems.
Tire Pressure You could lose control of your vehicle.
Proper tire inflation pressure is essential to the safe and • Over inflated or under inflated tires can affect
satisfactory operation of your vehicle. Three primary vehicle handling and can fail suddenly, resulting in
loss of vehicle control.
areas are affected by improper tire pressure:
• Unequal tire pressures from one side of the vehicle to
the other can cause the vehicle to drift to the right or
left.
• Always drive with each tire inflated to the recom-
mended cold tire inflation pressure.
check tire pressure. Do not make a visual judgement Check tire pressures more often if subject to a wide range
when determining proper inflation. Radial tires may look of outdoor temperatures, as tire pressures vary with
properly inflated even when they are under inflated. temperature changes.
Tire pressures change by approximately 1 psi (7 kPa) per
CAUTION!
12 °F (7 °C) of air temperature change. Keep this in mind
After inspecting or adjusting the tire pressure, al- when checking tire pressure inside a garage, especially in
ways reinstall the valve stem cap (if equipped). This the winter.
will prevent moisture and dirt from entering the Example: If garage temperature = 68 °F (20 °C) and the
valve stem, which could damage the valve stem. outside temperature = 32 °F (0 °C) then the cold tire 5
inflation pressure should be increased by 3 psi (21 kPa),
which equals 1 psi (7 kPa) for every 12 °F (7 °C) for this
Inflation pressures specified on the placard are always outside temperature condition.
“cold tire inflation pressure.” Cold tire inflation pressure
is defined as the tire pressure after the vehicle has not Tire pressure may increase from 2 to 6 psi (13 to 40 kPa)
been driven for at least 3 hours, or driven less than 1 mile during operation. DO NOT reduce this normal pressure
(1 km) after a 3 hour period. The cold tire inflation build up or your tire pressure will be too low.
pressure must not exceed the maximum inflation pres-
sure molded into the tire sidewall.
WARNING!
Cuts and punctures in radial tires are repairable only in
High speed driving with your vehicle under maxi- the tread area because of sidewall flexing. Consult your
mum load is dangerous. The added strain on your authorized tire dealer for radial tire repairs.
tires could cause them to fail. You could have a
serious accident. Don’t drive a vehicle loaded to the
maximum capacity at continuous speeds above 75
mph (120 km/h).
Compact Spare Tire — If Equipped Do not install a wheel cover or attempt to mount a
The compact spare is for temporary emergency use with conventional tire on the compact spare wheel, since the
radial tires. It is engineered to be used on your style wheel is designed specifically for the compact spare.
vehicle only. Since this tire has limited tread life, the
Do not install more than one compact spare tire/wheel
original tire should be repaired (or replaced) and rein-
on the vehicle at any given time.
stalled at the first opportunity.
CAUTION!
WARNING!
Because of the reduced ground clearance, do not take
Temporary use spare tires are for emergency use only.
your vehicle through an automatic car wash with the
5
With these tires, do not drive more than 50 mph (80
compact spare installed. Damage to the vehicle may
km/h). Temporary-use spare tires have limited tread
result.
life. When the tread is worn to the tread wear
indicators, the temporary use spare tire needs to be
replaced. Be sure to follow the warnings, which Limited Use Spare — If Equipped
apply to your spare. Failure to do so could result in The limited use spare tire is for temporary emergency use
spare tire failure and loss of vehicle control. on your vehicle. This tire is identified by a limited use
spare tire warning label located on the limited use spare
tire and wheel assembly. This tire may look like the
original equipped tire on the front or rear axle of your Tire Spinning
vehicle, but it is not. Installation of this limited use spare When stuck in mud, sand, snow, or ice conditions, do not
tire affects vehicle handling. Since it is not the same tire, spin your vehicle’s wheels faster than 30 mph (48 km/h)
replace (or repair) the original tire and reinstall on the or for longer than 30 seconds continuously without
vehicle at the first opportunity. stopping when you are stuck.
Refer to “Freeing A Stuck Vehicle” in Section 6 of this
WARNING!
manual for additional information.
The limited use spare tires are for emergency use
only. Installation of this limited use spare tire affects WARNING!
vehicle handling. With this tire, do not drive more
Fast spinning tires can be dangerous. Forces gener-
than 60 mph (100 km/h). Keep inflated to the cold tire
ated by excessive wheel speeds may cause tire dam-
inflation pressure listed on either your tire placard or
age or failure. A tire could explode and injure some-
limited use spare tire and wheel assembly. Replace
one. Do not spin your vehicle’s wheels faster than 30
(or repair) the original tire at the first opportunity
mph (48 km/h) or for more than 30 seconds continu-
and reinstall it on your vehicle. Failure to do so could
ously when you are stuck, and don’t let anyone near
result in loss of vehicle control.
a spinning wheel, no matter what the speed.
Tread Wear Indicators These indicators are molded into the bottom of the tread
Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth
to help you in determining when your tires should be becomes 1/16 inch (2 mm). When the tread is worn to the
replaced. tread wear indicators, the tire should be replaced.
Many states have laws requiring tire replacement at this
point.
Life of Tire
The service life of a tire is dependent upon varying
factors including but not limited to: 5
• Driving style
• Tire pressure
• Distance driven
Replacement Tires
WARNING!
The tires on your new vehicle provide a balance of many
Tires and spare tire should be replaced after six years, characteristics. They should be inspected regularly for
regardless of the remaining tread. Failure to follow wear and correct cold tire inflation pressure. The manu-
this warning can result in sudden tire failure. You facturer strongly recommends that you use tires equiva-
could lose control and have an accident resulting in lent to the originals in size, quality and performance
serious injury or death. when replacement is needed (refer to the paragraph on
“Tread Wear Indicators”). Refer to the “Tire and Loading
Information” placard for the size designation of your tire.
Keep dismounted tires in a cool, dry place with as little The service description and load identification will be
exposure to light as possible. Protect tires from contact found on the original equipment tire. Failure to use
with oil, grease, and gasoline. equivalent replacement tires may adversely affect the
safety, handling, and ride of your vehicle. We recommend
that you contact your original equipment or an autho-
rized tire dealer with any questions you may have on tire
specifications or capability.
WARNING! CAUTION!
• Do not use a tire, wheel size or rating other than Replacing original tires with tires of a different size
that specified for your vehicle. Some combina- may result in false speedometer and odometer
tions of unapproved tires and wheels may change readings.
suspension dimensions and performance charac-
teristics, resulting in changes to steering, han-
dling, and braking of your vehicle. This can cause
unpredictable handling and stress to steering and Alignment And Balance
suspension components. You could lose control Poor suspension alignment may result in:
and have an accident resulting in serious injury 5
or death. Use only the tire and wheel sizes with • Fast tire wear.
load ratings approved for your vehicle.
• Uneven tire wear, such as feathering and one-sided
• Never use a tire with a smaller load index or
capacity, other than what was originally equipped wear.
on your vehicle. Using a tire with a smaller load • Vehicle pull to right or left.
index could result in tire overloading and failure.
You could lose control and have an accident. Tires may also cause the vehicle to pull to the left or right.
• Failure to equip your vehicle with tires having Alignment will not correct this condition. See your dealer
adequate speed capability can result in sudden for proper diagnosis.
tire failure and loss of vehicle control.
NOTE: Do not use tire chains on a compact spare tire. • Do not exceed 45 mph (70 km/h).
• Drive cautiously and avoid severe turns and large bumps,
especially with a loaded vehicle.
• If chains are used on an All Wheel Drive (AWD) vehicle, they
should be used on all four tires.
• Do not drive for prolonged period on dry pavement.
• Observe the tire chain manufacturer’s instructions on the
method of installation, operating speed, and conditions for
use. Always use the lower suggested operating speed of the
chain manufacturer if different than the speed recommended
by the manufacture.
NOTE: In order to avoid damage to tires, chains, and Snow tires generally have lower speed ratings than what
your vehicle do not drive for a prolonged period of time was originally equipped with your vehicle and should
on dry pavement. Observe the tire chain manufacturer’s not be operated at sustained speeds over 75 mph (120
instructions on method of installation, operating speed, km/h).
and conditions for usage.
TIRE ROTATION
Always use the lower suggested operating speed if both Tires on the front and rear axles of vehicles operate at
the chain manufacturer and vehicle manufacture suggest different loads and perform different steering, driving,
a maximum speed. This notice applies to all chain and braking functions. For these reasons, they wear at
traction devices, including link and cable (radial) chains. unequal rates, and tend to develop irregular wear pat- 5
terns.
SNOW TIRES
Some areas of the country require the use of snow tires These effects can be reduced by timely rotation of tires.
during winter. Standard tires are of the all season type The benefits of rotation are especially worthwhile with
and satisfy this requirement as indicated by the M+S aggressive tread designs such as those on all season type
designation on the tire sidewall. tires. Rotation will increase tread life, help to maintain
mud, snow, and wet traction levels, and contribute to a
If you need snow tires, select tires equivalent in size and
smooth, quiet ride.
type to the original equipment tires. Use snow tires only
in sets of 4, failure to do so may adversely affect the
safety and handling of your vehicle.
Follow the recommended tire rotation frequency for your TIRE PRESSURE MONITOR SYSTEM (TPMS)
type of driving found in the “Maintenance Schedules” The TPMS will warn the driver of a low tire pressure
Section of this manual. More frequent rotation is permis- based on the vehicle recommended cold placard pressure
sible if desired. The reasons for any rapid or unusual (the placard is located on the drivers side B-pillar).
wear should be corrected prior to rotation being per-
The tire pressure will vary with temperature by about 1
formed.
psi (6.9 kPa) for every 12°F (6.5°C). This means that when
The suggested rotation method is the “forward-cross” the outside temperature decreases, the tire pressure will
shown in the following diagram. decrease. Tire pressure should always be set based on
cold inflation tire pressure. This is defined as the tire
pressure after a vehicle has not been driven for at least 3
hours or driven less than 1 mile (1 km) after a 3 hour
period, and in outside ambient temperature. Refer to the
“Tires – General Information” in this section for infor-
mation on how to properly inflate the vehicle’s tires.
The tire pressure will also increase as the vehicle is driven
- this is normal and there should be no adjustment for
this increased pressure.
The TPMS will warn the driver of a low tire pressure if For example, your vehicle may have a recommended
the tire pressure falls below the low pressure warning cold (parked for more than 3 hours) placard of 35 °F (241
threshold for any reason, including low temperature kPa). If the ambient temperature is 68 °F (20 °C) and the
effects, or natural air pressure loss through the tire. measured tire pressure is 30 psi (207 kPa), a temperature
drop to 20 °F (-7 °C) will decrease the tire pressure to
The TPMS will continue to warn the driver of low tire
approximately 26 psi (179 kPa). This tire pressure is
pressure as long as the condition exists, and will not turn
sufficiently low enough to turn ON the “Tire Pressure
off until the tire pressure is at or above recommended
Monitoring Light.” Driving the vehicle may cause the tire
cold placard pressure. Once the low tire pressure warn-
pressure to rise to approximately 30 psi (207 kPa), but the
ing has been illuminated, the tire pressure must be 5
“Tire Pressure Monitoring Light” will still be ON. In this
increased to the recommended cold placard pressure in
situation, the “Tire Pressure Monitoring Light” will turn
order for the TPMS warning lamp to be turned off. The
OFF only after the tires have been inflated to the vehicle’s
system will automatically update and the TPMS warning
recommended cold placard pressure value.
lamp will extinguish once the updated tire pressures
have been received. The vehicle may need to be driven
for up to 10 minutes above 15 mph (25 km/h) to receive
this information.
CAUTION! CAUTION!
The TPMS has been optimized for the original After inspecting or adjusting the tire pressure, al-
equipment tires and wheels. TPMS pressures have ways reinstall the valve stem cap. This will prevent
been established for the tire size equipped on your moisture and dirt from entering the valve stem,
vehicle. Undesirable system operation or sensor which could damage the TPMS sensor.
damage may result when using replacement equip-
ment that is not of the same size, type, and/or style.
NOTE:
Aftermarket wheels can cause sensor damage. Do not
• The TPMS is not intended to replace normal tire care
use aftermarket sealants or balance beads if your
and maintenance, or to provide warning of a tire
vehicle is equipped with a TPMS, as damage to the
failure or condition.
sensors may result.
• The TPMS should not be used as a tire pressure gauge
while adjusting your tire pressure.
• Driving on a significantly under-inflated tire causes
the tire to overheat and can lead to tire failure.Under-
inflation also reduces fuel efficiency and tire tread life,
and may affect the vehicle’s handling and stopping
ability.
• The TPMS is not a substitute for proper tire mainte- The Basic TPMS consists of the following components:
nance, and it is the driver’s responsibility to maintain
• Receiver Module
correct tire pressure, using an accurate tire pressure
gage, even if under-inflation has not reached the level • 4 Tire Pressure Monitoring Sensors
to trigger illumination of the TPMS Telltale Lamp.
• Tire Pressure Monitoring Telltale Lamp
• Seasonal temperature changes will affect tire pressure,
The Tire Pressure Monitoring Telltale Lamp
and the TPMS will monitor the actual tire pressure in
will illuminate in the instrument cluster and an
the tire.
audible chime will be activated when one or
Basic TPMS without EVIC — If Equipped more of the four active road tire pressures are 5
The TPMS uses wireless technology with wheel rim low. Should this occur you should stop as soon as
mounted electronic sensors to monitor tire pressure lev- possible, check the inflation pressure of each tire on your
els. Sensors, mounted to each wheel as part of the valve vehicle, and inflate each tire to the manufacturer recom-
stem, transmit tire pressure readings to the Receiver mended pressure, located on the tire pressure placard.
Module. The system will automatically update and the TPMS
warning light will extinguish once the updated tire
NOTE: It is particularly important, for you to check the
pressure(s) have been received.
tire pressure in all of your tires regularly and too main-
tain the proper pressure.
NOTE: The vehicle may need to be driven for up to 10 3. Accumulation of excessive snow and/or ice around
minutes above 15 mph (25 km/h) to receive this infor- the wheels or wheel housings.
mation.
4. Using tire chains on the vehicle.
The TPMS Telltale Lamp will flash on and off for 75
5. Using wheels/tires not equipped with TPMS sensors.
seconds, and remain on solid when a system fault is
detected. The system fault will also sound a chime. If the NOTE: Your vehicle is equipped with a compact spare
ignition key is cycled, this sequence will repeat, provid- wheel and tire assembly that does not have a tire pressure
ing the system fault still exists. The TPMS Telltale Lamp monitoring sensor. Therefore, it will not be monitored by
will turn off when the fault condition no longer exists. A the TPMS. In the event that the compact spare tire is
system fault can occur with any of the following sce- swapped with a low pressure road tire, each ignition key
narios: cycle will still show the TPMS Lamp to be ON, and a
chime to sound. Once you repair or replace the original
1. Jamming due to electronic devices or driving next to
road tire and reinstall it on the vehicle in place of the
facilities emitting the same radio frequencies as the TPMS
compact spare tire, the TPMS will update automatically,
sensors.
and the TPMS Lamp will turn OFF as long as no tire
2. Installing some form of aftermarket window tinting pressure is below the low-pressure warning limit in any
that affects radio wave signals. of the four active road tires. The vehicle may need to be
driven for up to 10 minutes above 15 mph (25 km/h) for
the TPMS to receive this information.
Basic TPMS with EVIC — If Equipped The TPMS Telltale Lamp will illuminate in the instru-
The TPMS uses wireless technology with wheel rim ment cluster, and an audible chime will be activated
mounted electronic sensors to monitor tire pressure lev- when one or more of the four active road tire pressures
els. Sensors, mounted to each wheel as part of the valve are low. In addition, EVIC will display the number of
stem, transmit tire pressure readings to the Receiver tire(s) that are low, followed by the “Tire Low Pressure”
Module. text message. Should this occur, you should stop as soon
as possible, check the inflation pressure of each tire on
NOTE: It is particularly important, for you to check the
you vehicle, and inflate each tire to the vehicle’s recom-
tire pressure in all of your tires regularly and too main-
mended cold placard pressure value. The system will
tain the proper pressure. 5
automatically update and the TPMS Lamp will extin-
The Basic TPMS consists of the following components: guish one the updated tire pressures have been received.
The vehicle may need to be driven for up to 10 minutes
• Receiver Module
above 15 mph (25 km/h) for the TPMS to receive this
• 4 Tire Pressure Monitoring Sensors information.
• Various TPMS Messages, which display in the Elec- The TPMS Telltale Lamp will flash on and off for 75
tronic Vehicle Information Center (EVIC). seconds, and remain on solid when a system fault is
detected. The system fault will also sound a chime. In
• Tire Pressure Monitoring Telltale Lamp
addition, EVIC will display a “SERVICE TIRE SYSTEM
SOON” text message. If the ignition key is cycled, this
sequence will repeat, providing the system fault still the TPMS. In the event that the compact spare tire is
exists. The TPMS Telltale Lamp will turn off when the swapped with a low pressure road tire, each ignition key
fault condition no longer exists. A system fault can occur cycle will still show the TPMS Lamp to be ON, a chime to
with any of the following scenarios: sound, and a “1 Tire Low Pressure” message to appear in
the EVIC. Once you repair or replace the original road
1. Jamming due to electronic devices or driving next to
tire and reinstall it on the vehicle in place of the compact
facilities emitting the same radio frequencies as the TPMS
spare tire, the TPMS will update automatically, and the
sensors.
TPMS Lamp will turn OFF as long as no tire pressure is
2. Installing some form of aftermarket window tinting below the low-pressure warning limit in any of the four
that affects radio wave signals. active road tires. The vehicle may need to be driven for
up to 10 minutes above 15 mph (25 km/h) for the TPMS
3. Accumulation of excessive snow and/or ice around
to receive this information.
the wheels or wheel housings.
Premium TPMS – If Equipped
4. Using tire chains on the vehicle.
The TPMS uses wireless technology with wheel rim
5. Using wheels/tires not equipped with TPMS sensors. mounted electronic sensors to monitor tire pressure lev-
els. Sensors, mounted to each wheel as part of the valve
NOTE: Your vehicle is equipped with a compact spare
stem, transmit tire pressure readings to the Receiver
wheel and tire assembly that does not have a tire pressure
Module.
monitoring sensor. Therefore, it will not be monitored by
NOTE: It is particularly important, for you to check the Tire Pressure Monitoring Low Pressure Warnings
tire pressure in all of your tires regularly and to maintain The TPMS Telltale Lamp will illuminate in the instru-
the proper pressure. ment cluster, and an audible chime will be activated
when one or more of the four active road tire pressures
The TPMS consists of the following components:
are low. The EVIC will show a graphic display of the
• Receiver Module pressure value(s) with the low tire(s) flashing.
• 4 Tire Pressure Monitoring Sensors
• 3 Trigger Modules (mounted in three of the four wheel
wells) 5
• Various TPMS Messages, which display in the Elec-
tronic Vehicle Information Center (EVIC), and a
graphic displaying tire pressures.
• Yellow Tire Pressure Monitoring Telltale Light
NOTE: Low pressure in the spare or compact tire Service Tire System Soon
(which has no sensor and therefore not monitored) will The TPMS Telltale Lamp will flash on and off for 75
not cause the TPMS Telltale Lamp to illuminate or the seconds, and remain on solid when a system fault is
chime to sound. detected. The system fault will also sound a chime. In
addition, the EVIC will display a “SERVICE TIRE SYS-
Should a low tire condition occur on any of the four
TEM SOON” text message for 3 seconds. This text
active road tire(s), you should stop as soon as possible,
message is then followed by “— —”, for the pressure
and inflate the low tire(s) that is flashing on the graphic
value(s) indicating which TPMS Sensor(s) is not being
display to the vehicle’s recommended cold placard pres-
received.
sure value. The system will automatically update, the
graphic display of the pressure value(s) will stop flash-
ing, and the TPMS Lamp will extinguish once the up-
dated tire pressure(s) have been received. The vehicle
may need to be driven for up to 10 minutes above 15 mph
(25 km/h) for the TPMS to receive this information.
ADDING FUEL
5
Fuel Filler Cap (Gas Cap) CAUTION!
As a reminder, a fuel icon with an arrow
indicating which side of the vehicle the fuel To avoid fuel spillage and overfilling, do not “top
filler door is located on, is located in the off” the fuel tank after filling.
instrument cluster, just below the Fuel Gage.
The gas cap is located behind the fuel filler door on the
NOTE: When the fuel nozzle “clicks” or shuts off, the
left side of the vehicle. If the gas cap is lost or damaged,
fuel tank is full.
be sure the replacement cap is for use with this vehicle.
Tighten the fuel filler cap properly and press the Vehicle Certification Label
odometer reset button to turn the gASCAP message Your vehicle has a certification label attached to the rear
off. of the driver’s door.
• Make sure that the fuel filler cap is tightened each time The label contains the following information:
the vehicle is refueled.
• Name of manufacturer
• If the problem continues, the message will appear the
• Month and year of manufacture
next time the vehicle is started. See your authorized
dealer service center as soon as possible. See Section 7 • Gross Vehicle Weight Rating (GVWR)
of this manual for more information. 5
• Gross Axle Weight Rating (GAWR) front
VEHICLE LOADING • Gross Axle Weight Rating (GAWR) rear
The load carrying capacity of your vehicle is shown in the
charts that follow. This information should be used for • Vehicle Identification Number (VIN)
passenger and luggage loading as indicated. • Type of Vehicle
If the seatbacks are folded for carrying cargo, do not • Month Day and Hour of Manufacture (MDH)
exceed the specified GVWR and GAWR.
The bar code allows a computer scanner to read the
Vehicle Identification Number (VIN).
Loading
To load your vehicle properly, first figure out its empty
weight, axle by axle and side by side. Store heavier items
down low and be sure you distribute their weight as
evenly as possible. Stow all loose items securely before
driving. If weighing the loaded vehicle shows that you
have exceeded either GAWR, but the total load is within
the specified GVWR, you must redistribute the weight.
Improper weight distribution can have an adverse effect
on the way your vehicle steers and handles and the way 5
the brakes operate.
A loaded vehicle is shown in the illustration. Note that
neither the GVWR or the GAWR capacities have been
exceeded.
Towing Requirements
To promote proper break-in of your new vehicle driv- Perform the maintenance listed in Section 8 of this
etrain components the following guidelines are recom- manual. When towing a trailer, never exceed the GAWR,
mended: or GCWR, ratings.
Make certain that the load is secured in the trailer • Vehicles with trailers should not be parked on a grade.
and will not shift during travel. When trailering When parking, apply the parking brake on the tow
cargo that is not fully secured, dynamic load shifts vehicle. Put the tow vehicle automatic transmission in
can occur that may be difficult for the driver to P for Park. Always, block or 9chock9 the trailer wheels. 5
control. You could lose control of your vehicle and • GCWR must not be exceeded.
have an accident.
• Total weight must be distributed between the tow
vehicle and the trailer such that the following four
• When hauling cargo or towing a trailer, do not over- ratings are not exceeded:
load your vehicle or trailer. Overloading can cause a
1. GVWR
loss of control, poor performance or damage to brakes,
axle, engine, transmission, steering, suspension, chas- 2. GTW
sis structure or tires.
3. GAWR
4. Tongue weight rating for the trailer hitch utilized − When replacing tires refer to the Tires–General Infor-
(This requirement may limit the ability to always mation section of this manual on Replacement Tires for
achieve the 10% to 15% range of tongue weight as a proper tire replacement procedures. Replacing tires
percentage of total trailer weight). with a higher load carrying capacity will not increase
the vehicle’s GVWR and GAWR limits.
Towing Requirements — Tires
Towing Requirements — Trailer Brakes
− Do not attempt to tow a trailer while using a compact
spare tire. − Do not interconnect the hydraulic brake system or
vacuum system of your vehicle with that of the trailer.
− Proper tire inflation pressures are essential to the safe
This could cause inadequate braking and possible
and satisfactory operation of your vehicle. Refer to the
personal injury.
Tires–General Information section of this manual on
Tire Pressures for proper tire inflation procedures. − An electronically actuated trailer brake controller is
required when towing a trailer with electronically
− Also, check the trailer tires for proper tire inflation
actuated brakes. When towing a trailer equipped with
pressures before trailer usage.
a hydraulic surge actuated brake system, an electronic
− Check for signs of tire wear or visible tire damage brake controller is not required.
before towing a trailer. Refer to the Tires–General
Information section of this manual on Tread Wear
Indicators for the proper inspection procedure.
4 - Pin Connector
− City Driving NOTE: If the vehicle requires towing make sure all four
When stopped for short periods of time, put transmission wheels are off the ground.
in neutral but do not increase engine idle speed.
− Highway Driving
Reduce speed.
CONTENTS
m Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 350 m Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . 362
m If Your Engine Overheats . . . . . . . . . . . . . . . . . 351 m Towing A Disabled Vehicle . . . . . . . . . . . . . . . . 363
m Jacking And Tire Changing . . . . . . . . . . . . . . . . 352 ▫ With Ignition Key . . . . . . . . . . . . . . . . . . . . . 363
▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . . 352 ▫ Without The Ignition Key . . . . . . . . . . . . . . . 365 6
▫ Spare Tire Stowage . . . . . . . . . . . . . . . . . . . . 354 ▫ Towing This Vehicle Behind Another Vehicle
(Flat Towing With All Four Wheels On The
▫ Preparations For Jacking . . . . . . . . . . . . . . . . 355
Ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 365
▫ Jacking Instructions . . . . . . . . . . . . . . . . . . . . 356
▫ Towing This Vehicle Behind Another Vehicle
m Jump-Starting Procedure . . . . . . . . . . . . . . . . . . 360 With A Tow Dolly . . . . . . . . . . . . . . . . . . . . . 365
HAZARD WARNING FLASHER To engage the Hazard Warning Flashers, depress the
switch on the instrument panel. When the Hazard Warn-
ing Switch is activated, all directional turn signals will
flash on and off to warn oncoming traffic of an emer-
gency. Push the switch a second time to turn off the
flashers.
CAUTION!
The hazard flasher switch is located in the center of When you must leave the vehicle to seek assistance, the
the instrument panel above the center air outlets. Hazard Warning Flashers will continue to operate even
though the ignition switch is OFF.
NOTE: With extended use, the Hazard Warning Flash- the fan control to High. This allows the heater core to act
ers may wear down your battery. as a supplement to the radiator and aids in removing heat
from the engine cooling system.
IF YOUR ENGINE OVERHEATS
In any of the following situations, you can reduce the CAUTION!
potential for overheating by taking the appropriate ac-
tion. Driving with a hot cooling system could damage
your vehicle. If temperature gauge reads “H”, pull
• On the highways — Slow down.
over and stop the vehicle. Idle the vehicle with the air
• In city traffic — While stopped, put transmission in conditioner turned off until the pointer drops back
neutral, but do not increase engine idle speed. into the normal range. If the pointer remains on the
NOTE: There are steps that you can take to slow down
“H”, turn the engine off immediately, and call for 6
an impending overheat condition. If your air conditioner service.
is on, turn it off. The air conditioning system adds heat to
the engine cooling system and turning off the A/C
removes this heat. You can also turn the Temperature
control to maximum heat, the Mode control to floor, and
WARNING!
6
Jack Wing Nut
Jack Location
CAUTION! WARNING!
The winch mechanism is designed for use with the Do not attempt to change a tire on the side of the
jack handle only. Use of an air wrench or other power vehicle close to moving traffic. Pull far enough off
tools is not recommended and can damage the winch. the road to avoid the danger of being hit when
operating the jack or changing the wheel.
When the spare is clear, tilt the retainer at the end of the
cable and pull it through the center of the wheel. • Turn on the Hazard Warning Flasher.
Preparations For Jacking • Block both the front and rear
Park the vehicle on a firm level surface, avoid ice or of the wheel diagonally oppo- 6
slippery areas, set the parking brake and place the gear site the jacking position. For
selector in PARK. Turn OFF the ignition. example, if changing the right
front tire, block the left rear
wheel.
• Passengers should not remain in the vehicle when the
vehicle is being jacked.
Jacking Instructions
WARNING!
WARNING! Carefully follow these tire changing warnings to help pre-
vent personal injury or damage to your vehicle:
• Getting under a jacked-up vehicle is dangerous.
• Always park on a firm, level surface as far from the edge
The vehicle could slip off the jack and fall on you. of the roadway as possible before raising the vehicle.
You could be crushed. Never get any part of your • Block the wheel diagonally opposite the wheel to be
body under a vehicle that is on a jack. Never start raised.
or run the engine while the vehicle is on a jack. If • Apply the parking brake firmly before jacking.
you need to get under a raised vehicle, take it to a
• Never start the engine with the vehicle on a jack.
service center where it can be raised on a lift.
• Do not let anyone sit in the vehicle when it is on a jack.
• The jack is designed to use as a tool for changing
• Do not get under the vehicle when it is on a jack.
tires only. The jack should not be used to lift the
vehicle for service purposes. The vehicle should • Only use the jack in the positions indicated.
be jacked on a firm level surface only. Avoid ice or • If working on or near a roadway, be extremely careful of
slippery areas. motor traffic.
• To assure that spare tires, flat or inflated are securely
stowed, spares must be stowed with the value stem
facing the ground.
location. Do not raise the vehicle until you are sure the 7. Remove the wheel lug nuts, for vehicles with wheel
jack is securely engaged. Never jack up the vehicle covers, remove the cover from the wheel by hand. Do not
using any suspension components. pry the wheel cover off. Then pull the wheel off the hub.
6. Raise the vehicle by turning the jack screw to the right, 8. Install the spare wheel, for vehicles with wheel covers,
using the swivel wrench. Raise the vehicle only until the align the notch in the wheel cover with the valve stem on
tire just clears the surface and enough clearance is the wheel. Install the cover on the wheel by hand only
obtained to install the spare tire. Minimum tire lift and install the wheel lug nuts with the cone shaped end
provides maximum stability. of the nut toward the wheel. Lightly tighten the lug nuts.
To avoid the risk of forcing the vehicle off the jack, do not
WARNING! tighten the lug nuts fully until the vehicle has been
lowered.
Raising the vehicle higher than necessary can make
the vehicle less stable. It could slip off the jack and NOTE: Do not install the wheel cover on the compact
hurt someone near it. Raise the vehicle only enough spare.
to remove the tire. Do not use a hammer or force to install the wheel covers.
9. Lower the vehicle by turning the jack screw to the left.
10. Finish tightening the lug nuts. Push down on the
wrench while tightening for increased leverage. Alternate
lug nuts until each nut has been tightened twice. Correct • Turn the wheel so that the valve-stem is down. Slide
wheel nut tightness is 130 N·m (95 ft. lbs). If in doubt the wheel retainer through the center of the wheel
about the correct tightness, have them checked with a and position it properly across the wheel opening.
torque wrench by your dealer or at a service station.
• For convenience in checking the spare tire inflation,
11. Lower the jack to its fully closed position. stow with the valve-stem toward the rear of the
vehicle.
WARNING!
• Using the jack-handle, rotate the drive nut to the
A loose tire or jack, thrown forward in a collision or right until the wheel is drawn into place against the
hard stop could endanger the occupants of the ve- underside of the vehicle.
hicle. Always stow the jack parts and the spare tire in • Continue to rotate the nut until you hear the mecha- 6
the places provided. nism click three times. It cannot be overtightened.
Push against the tire several times to be sure it is
securely in place.
NOTE: The full size flat tire will not store under the
vehicle. It should be repaired /or replaced, and rein- 13. Stow the jack and jack handle.
stalled on the vehicle as soon as possible. 14. Check the tire pressure as soon as possible. Correct
12. Secure the spare tire as follows: pressure as required.
NOTE: When reinstalling the wheel center cap, insure JUMP-STARTING PROCEDURE
that the valve stem symbol on the back of the cap is
pointed toward the wheel valve stem. Install the center WARNING!
cap using hand pressure only. Do not use a hammer.
• Do not attempt to push or tow your vehicle to get it started.
Vehicles equipped with an automatic transmission cannot
Wheel Nuts be started this way. Unburned fuel could enter the catalytic
All wheel nuts should be tightened occasionally to elimi- converter and once the engine has started, ignite and
damage the converter and vehicle. If the vehicle has a
nate the possibility of wheel studs being sheared or the discharged battery, booster cables may be used to obtain a
bolt holes in the wheels becoming elongated. This is start from another vehicle. This type of start can be danger-
ous if done improperly, so follow this procedure carefully.
especially important during the first few hundred miles
of operation, and after each time a tire is changed, to • Battery fluid is a corrosive acid solution; do not allow
battery fluid to contact eyes, skin or clothing. Don’t lean
allow the wheel nuts to become properly set. All nuts over battery when attaching clamps or allow the clamps to
should first be firmly seated against the wheel. The nuts touch each other. If acid splashes in eyes or on skin, flush
contaminated area immediately with large quantities of
should then be tightened to recommended torque. water.
Tighten the nuts to final torque in increments. Progress • A battery generates hydrogen gas which is flammable and
around the bolt circle, tightening the nut opposite to the explosive. Keep flame or spark away from the vent holes.
Do not use a booster battery or any other booster source
nut just previously tightened until final torque is with an output that exceeds 12 volts.
achieved. Recommended torque is 130 N·m (95 ft. lbs). • Take care to avoid the radiator cooling fan whenever the
hood is raised. It can start anytime the ignition switch is on.
You can be hurt by the fan.
WARNING! WARNING!
Do not connect the cable to the negative post of the Any procedure other than above could result in:
discharge battery. The resulting electrical spark could 1. Personal injury caused by electrolyte squirting out
cause the battery to explode. the battery vent;
During cold weather when temperatures are below 2. Personal injury or property damage due to battery
freezing point, electrolyte in a discharged battery explosion;
may freeze. Do not attempt jump starting because the
battery could rupture or explode. The battery tem- 3. Damage to charging system of booster vehicle or
perature must be brought up above freezing point of immobilized vehicle.
before attempting jump start.
If it is necessary to use the accessories while being towed TOWING THIS VEHICLE BEHIND ANOTHER
(wipers, defrosters, etc.), the key must be in the ON VEHICLE (Flat towing with all four wheels on the
position, not the ACCESSORY position. Make certain the ground)
transmission remains in NEUTRAL. Flat towing of vehicles equipped with an automatic
transmission, is only permitted within the limitations
Without The Ignition Key
described in this section.
Special care must be taken when the vehicle is towed
with the ignition in the LOCK position. The only ap- TOWING THIS VEHICLE BEHIND ANOTHER
proved method of towing with out the ignition key is VEHICLE WITH A TOW DOLLY
with a flat bed truck. Proper towing equipment is neces- The manufacturer does not recommend that you tow an
sary to prevent damage to the vehicle. All-Wheel Drive (AWD) or front wheel drive vehicle on a
tow dolly. Vehicle damage may occur. 6
CONTENTS
m 3.8L Engines . . . . . . . . . . . . . . . . . . . . . . . . . . 370 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . 376
m 4.0L Engines . . . . . . . . . . . . . . . . . . . . . . . . . . 371 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . . 379
m Onboard Diagnostic System — OBD II . . . . . . . . 372 ▫ Drive Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . 379
▫ Loose Fuel Filler Cap Message . . . . . . . . . . . . 373 ▫ Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . 379
m Emissions Inspection And Maintenance ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . . 380 7
Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373
▫ Catalytic Converter . . . . . . . . . . . . . . . . . . . . 380
m Replacement Parts . . . . . . . . . . . . . . . . . . . . . . 375
▫ Maintenance-Free Battery . . . . . . . . . . . . . . . . 382
m Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . 375
▫ Air Conditioner Maintenance . . . . . . . . . . . . . 383
m Maintenance Procedures . . . . . . . . . . . . . . . . . . 376
▫ Power Steering — Fluid Check . . . . . . . . . . . . 385
▫ Front & Rear Suspension Ball Joints . . . . . . . . 385 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 398
▫ Steering Shaft Seal . . . . . . . . . . . . . . . . . . . . 385 ▫ All Wheel Drive (AWD) — If Equipped . . . . . 400
▫ Steering Linkage . . . . . . . . . . . . . . . . . . . . . . 386 ▫ Front And Rear Wheel Bearings . . . . . . . . . . . 401
▫ Drive Shaft Universal Joints . . . . . . . . . . . . . . 386 ▫ Appearance Care And Protection From
Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . . 401
▫ Body Lubrication . . . . . . . . . . . . . . . . . . . . . 386
▫ Cleaning The Center Console Cup Holders . . . 406
▫ Windshield Wiper Blades . . . . . . . . . . . . . . . . 387
m Fuses (Integrated Power Module) . . . . . . . . . . . 407
▫ Windshield And Rear Window Washers . . . . . 387
m Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . . 410
▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . . 388
m Replacement Light Bulbs . . . . . . . . . . . . . . . . . 411
▫ Cooling System . . . . . . . . . . . . . . . . . . . . . . . 389
m Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . 412
▫ Hoses And Vacuum/Vapor Harnesses . . . . . . . 394
▫ Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 412
▫ Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
▫ High Intensity Discharge Headlights (HID) —
▫ Master Cylinder — Brake Fluid Level Check . . 396
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 413
▫ Fuel System Hoses . . . . . . . . . . . . . . . . . . . . 397
3.8L ENGINES
4.0L ENGINES
Your vehicle has a simple ignition key actuated test, ignition key or start the engine. This means that your
which you can use prior to going to the test station. To vehicle’s OBD system is not ready and you should not
check if your vehicle’s OBD system is ready, you must do proceed to the I/M station.
the following:
b. The MIL will not flash at all and will remain fully
1. Insert your ignition key into the ignition switch. illuminated until you turn off the ignition key or start
the engine. This means that your vehicle’s OBD system
2. Turn the ignition to the ON position, but do not crank
is ready and you can proceed to the I/M station.
or start the engine.
If your OBD system is not ready, you should see your
3. If you crank or start the engine, you will have to start
authorized dealer or repair facility. If your vehicle was
this test over.
recently serviced or had a battery failure or replacement,
4. As soon as you turn your key to the ON position, you you may need to do nothing more than drive your
will see your MIL symbol come on as part of a normal vehicle as you normally would in order for your OBD
bulb check. system to update. A recheck with the above test routine
may then indicate that the system is now ready.
5. Approximately 15 seconds later, one of two things will
happen: Regardless of whether your vehicle’s OBD system is
ready or not ready, if the MIL symbol is illuminated
a. The MIL will flash for about 10 seconds and then
during normal vehicle operation, you should have your
return to being fully illuminated until you turn off the
vehicle serviced before going to the I/M station. The I/M NOTE: Intentional tampering with emissions control
station can fail your vehicle because the MIL symbol is on systems can result in civil penalties being assessed
with the engine running. against you.
MAINTENANCE PROCEDURES The best time to check the engine oil level is about 5
The pages that follow contain the required maintenance minutes after a fully warmed engine is shut off. Do not
services determined by the engineers who designed your check oil level before starting the engine after it has sat
vehicle. overnight. Checking engine oil level when the engine is
cold will give you an incorrect reading.
Besides the maintenance items for which there are fixed
maintenance intervals, there are other items that should Checking the oil while the vehicle is on level ground will
operate satisfactorily without periodic maintenance. improve the accuracy of the oil level readings. Maintain
However, if a malfunction of these items does occur, it the oil level between the MIN and MAX markings on the
could adversely affect the engine or vehicle performance. dipstick. Adding one quart of oil when the reading is at
These items should be inspected if a malfunction is the MIN mark will result in a MAX reading on these
observed or suspected. engines.
Engine Oil
Checking Oil Level
To assure proper engine lubrication, the engine oil must
be maintained at the correct level. Check the oil level at
regular intervals, such as every fuel stop.
American Petroleum Institute (API) Engine Oil Engine Oil Viscosity (SAE Grade) — 3.8 Liter
Identification Symbol Engines
This symbol means that the oil has SAE 5W-20 engine oil is recommended for all operating
been certified by the American temperatures. This engine oil improves low temperature
Petroleum Institute (API). The starting and vehicle fuel economy. Your engine oil filler
manufacturer only recommends cap also shows the recommended engine oil viscosity for
API Certified engine oils. your vehicle.
For information on engine oil filler cap location, refer to
the Engine Compartment illustration in this section.
Lubricants which do not have both, the engine oil certi-
Engine Oil Viscosity (SAE Grade) — 4.0 Liter fication mark and the correct SAE viscosity grade num-
Engines ber should not be used.
SAE 10W-30 engine oil is preferred for all operating
temperatures. The engine oil filler cap also shows the Synthetic Engine Oils
recommended engine oil viscosity for your vehicle. You may use synthetic engine oils provided the recom-
mended oil quality requirements are met, and the recom-
Lubricants which do not have both, the engine oil certi- mended maintenance intervals for oil and filter changes
fication mark and the correct SAE viscosity grade num- are followed.
ber should not be used.
Catalytic Converter
The catalytic converter requires the use of unleaded fuel
only. Leaded gasoline will destroy the effectiveness of the
catalyst as an emission control device.
Under normal operating conditions, the catalytic con- NOTE: Intentional tampering with emissions control
verter will not require maintenance. However, it is im- systems can result in civil penalties being assessed
portant to keep the engine properly tuned to assure against you.
proper catalyst operation and prevent possible catalyst
damage. WARNING!
CAUTION! A hot exhaust system can start a fire if you park over
materials that can burn. Such materials might be grass
Damage to the catalytic converter can result if your or leaves coming into contact with your exhaust system.
vehicle is not kept in proper operating condition. In Do not park or operate your vehicle in areas where your
the event of engine malfunction, particularly involv- exhaust system can contact anything that can burn.
ing engine misfire or other apparent loss of perfor-
mance, have your vehicle serviced promptly. Contin-
ued operation of your vehicle with a severe In unusual situations involving grossly malfunctioning 7
malfunction could cause the converter to overheat, engine operation, a scorching odor may indicate severe
resulting in possible damage to the converter and the and abnormal catalyst overheating. If this occurs, the
vehicle. vehicle should be stopped, the engine shut off and the
vehicle allowed to cool. Thereafter, service, including a
tune-up to manufacturer’s specifications, should be ob-
tained immediately.
Refer to the “Maintenance Schedule” section of this If necessary, add fluid to restore to the proper indicated
manual for the recommended air conditioning filter level. With a clean cloth, wipe any spilled fluid from all
replacement intervals. surfaces. Refer to Fluids, Lubricants, and Genuine Parts
for correct fluid type.
Power Steering — Fluid Check
Checking the power steering fluid level at a defined Front & Rear Suspension Ball Joints
service interval is not required. The fluid should only be The suspension ball joints are permanently sealed. No
checked if a leak is suspected, abnormal noises are regular maintenance is required for these components.
apparent, and/or the system is not functioning as antici-
Steering Shaft Seal
pated. Coordinate inspection efforts through a certified
The steering shaft seal, at the point where the shaft passes
DaimlerChrysler Dealership.9
through the bulkhead, is lubricated when it is installed. If
the seal becomes noisy when the steering shaft is turned,
WARNING!
it should be lubricated with a multi-purpose grease.
Mopar multi-purpose lubricant is recommended. 7
Fluid level should be checked on a level surface and
with the engine off to prevent injury from moving
parts and to insure accurate fluid level reading. Do
not overfill. Use only manufacturers recommended
power steering fluid.
Windshield Wiper Blades washer solvent (not radiator antifreeze) and operate the
The rubber edges of the wiper blades and the windshield system for a few seconds to flush out the residual water.
should be cleaned periodically with a sponge or soft cloth
The washer fluid reservoir will hold a full gallon of fluid
and a mild nonabrasive cleaner. This will remove accu-
when the Low Washer Fluid Light illuminates.
mulations of salt or road film.
Operation of the wipers on dry glass for long periods
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt
from a dry windshield.
Avoid using the wiper blades to remove frost or ice from
the windshield. Keep the blade rubber out of contact with
petroleum products such as engine oil, gasoline, etc.
7
Windshield and Rear Window Washers
The fluid reservoir for the windshield washers and the
rear window washer is shared. It is located in the engine
compartment and should be checked for fluid level at Washer Fluid Reservoir
regular intervals. Fill the reservoir with windshield
Exhaust System
WARNING!
The best protection against carbon monoxide entry into
the vehicle body is a properly maintained engine exhaust Exhaust gases can injure or kill. They contain carbon
system. monoxide (CO) which is colorless and odorless.
Whenever a change is noticed in the sound of the exhaust Breathing it can make you unconscious and can
system, when exhaust fumes can be detected inside the eventually poison you. To avoid breathing CO, refer
vehicle, or when the underside or rear of the vehicle is to “Exhaust Gas” in the Safety Tips section of this
damaged, have a competent mechanic inspect the com- manual.
plete exhaust system and adjacent body areas for broken,
damaged, deteriorated, or mispositioned parts. Open
seams or loose connections could permit exhaust fumes
to seep into the passenger compartment. In addition,
inspect the exhaust system each time the vehicle is raised
for lubrication or oil change. Replace as required.
Adding Engine Coolant The use of lower quality water will reduce the amount of
Your vehicle has been built with an improved engine corrosion protection in the engine cooling system.
coolant that allows extended maintenance intervals. This
Please note that it is the owner’s responsibility to main-
coolant can be used up to 5 Years or 100,000 miles before
tain the proper level of protection against freezing ac-
replacement. To prevent reducing this extended mainte-
cording to the temperatures occurring in the area where
nance period, it is important that you use the same
the vehicle is operated.
coolant throughout the life of your vehicle. Please review
these recommendations for using Hybrid Organic Addi- NOTE: Mixing coolant types will decrease the life of the
tive Technology (HOAT) coolant. engine coolant and will require more frequent coolant
changes.
When adding coolant, a minimum solution of 50% rec-
ommended Mopar Antifreeze/ Coolant 5 Year / 100,000 Cooling System Pressure Cap
Mile Formula HOAT (Hybrid Organic Additive Technol- The cap must be fully tightened to prevent loss of
ogy), or equivalent, in water should be used. Use higher coolant, and to insure that coolant will return to the 7
concentrations (not to exceed 70%) if temperatures below radiator from the coolant recovery bottle.
234°F (237°C ) are anticipated.
The cap should be inspected and cleaned if there is any
Use only high purity water such as distilled or deionized accumulation of foreign material on the sealing surfaces.
water when mixing the water/engine coolant solution.
When additional coolant is needed to maintain the • Check coolant freeze point in the radiator and in the
proper level, it should be added to the coolant bottle. Do coolant recovery bottle. If antifreeze needs to be
not overfill. added, contents of coolant recovery bottle must also be
protected against freezing.
Points To Remember
• If frequent coolant additions are required, or if the
NOTE: When the vehicle is stopped after a few miles (a
level in the coolant recovery bottle does not drop when
few kilometers) of operation, you may observe vapor
the engine cools, the cooling system should be pres-
coming from the front of the engine compartment. This is
sure tested for leaks.
normally a result of moisture from rain, snow, or high
humidity accumulating on the radiator and being vapor- • Maintain coolant concentration at 50% HOAT engine
ized when the thermostat opens, allowing hot coolant to coolant (minimum) and distilled water for proper
enter the radiator. corrosion protection of your engine which contains
aluminum components.
If an examination of your engine compartment shows no 7
evidence of radiator or hose leaks, the vehicle may be • Make sure that the radiator and coolant recovery
safely driven. The vapor will soon dissipate. bottle overflow hoses are not kinked or obstructed.
• Do not overfill the coolant recovery bottle. • Keep the front of the radiator clean. If your vehicle is
equipped with air conditioning, keep the front of the
condenser clean, also.
• Do not change the thermostat for summer or winter Insure nylon tubing in these areas has not melted or
operation. If replacement is ever necessary, install collapsed.
ONLY the correct type thermostat. Other designs may
Inspect all hose connections such as clamps and cou-
result in unsatisfactory coolant performance, poor gas
plings to make sure they are secure and no leaks are
mileage, and increased emissions.
present.
Hoses And Vacuum/Vapor Harnesses
Components should be replaced immediately if there is
Inspect surfaces of hoses and nylon tubing for evidence
any evidence of wear or damage that could cause failure.
of heat and mechanical damage. Hard or soft spots,
brittle rubber, cracking, tears, cuts, abrasions, and exces- Brakes
sive swelling indicate deterioration of the rubber. In order to assure brake system performance, all brake
system components should be inspected periodically.
Pay particular attention to those hoses nearest to high
Suggested service intervals can be found in the Mainte-
heat sources such as the exhaust manifold. Inspect hose
nance Schedules.
routing to be sure hoses do not come in contact with any
heat source or moving component which may cause heat
damage or mechanical wear.
should be replaced immediately! Eventual deterioration Clean the top of the master cylinder area before removing
of the hose can take place resulting in a possibility of a the cap. Add fluid to bring the level up to the top of the
burst failure. “FULL” mark on the side of the master cylinder reservoir.
Overfilling of fluid is not recommended because it may
WARNING!
cause leaking in the system.
Worn brake hoses can burst and cause brake failure. Add enough fluid to bring the level up to the require-
You could have an accident. If you see any signs of ments described on the brake fluid reservoir. With disc
cracking, scuffing, or worn spots, have the brake brakes, fluid level can be expected to fall as the brake
hoses replaced immediately. pads wear. However, low fluid level may be caused by a
leak and a checkup may be needed.
Master Cylinder — Brake Fluid Level Check Use only manufacturers recommended brake fluid, refer
The fluid level in the master cylinder should be checked to Fluids, Lubricants and Genuine Parts for correct fluid
when performing underhood services, or immediately if type.
the brake system warning light indicates system failure.
WARNING! CAUTION!
• Overfilling the brake fluid reservoir can result in Do not allow petroleum base fluid to contaminate the
spilling brake fluid on hot engine parts and the brake fluid, all brake seal components could be
brake fluid catching fire. damaged causing partial or complete brake failure.
• Use of brake fluid that may have a lower initial
boiling point or unidentified as to specification,
Fuel System Hoses
may result in sudden brake failure during hard Electronic Fuel Injection high pressure fuel systems are
prolonged braking. You could have an accident. designed with hoses and quick connect fittings which
have unique material characteristics to provide adequate
Use only brake fluid that has been in a tightly closed sealing and resist attack by deteriorated gasoline.
container to avoid contamination from foreign matter or You are urged to use only the manufacture specified 7
moisture. hoses with quick connect fittings, or their equivalent in
material and specification, in any fuel system servicing. It
is mandatory to replace any damaged hoses or quick
connect fittings that have been removed during service.
Care should be taken in installing quick connect fittings for correct fluid type. It is important that the transmission
to insure they are properly installed and fully connected. fluid be maintained at the prescribed level using the
See your authorized dealer for service. recommended fluid.
Automatic Transmission
CAUTION!
The automatic transmission and differential assembly are
contained within a single housing. Using a transmission fluid other than the manufac-
All automatic transmissions are equipped with a conven- turers recommended fluid may cause deterioration in
tional filler tube and dipstick. If fluid is added, it should transmission shift quality and/or torque converter
be added through the dipstick hole in the case. shudder. Using a transmission fluid other than the
manufacturers recommended fluid will result in
The dipstick is located just behind the radiator, lower more frequent fluid and filter changes. Refer to
right side. Fluids, Lubricants and Genuine Parts for correct
Selection of Lubricant fluid type.
It is important that the proper lubricant is used in the
transmission to assure optimum transmission perfor-
mance. Use only manufacturers recommended transmis-
sion fluid, refer to Fluids, Lubricants and Genuine Parts
If the fluid level indicates low, add sufficient fluid to NOTE: Refer to Section 8 of this manual for Mainte-
bring to the proper level. nance Schedules.
If the transmission is disassembled for any reason, the
CAUTION!
fluid and filter should be changed.
Do not overfill. Dirt and water in the transmission Special Additives
can cause serious damage. To prevent dirt and water Automatic Transmission Fluid (ATF) is an engineered
from entering the transmission after checking or product and its performance may be impaired by supple-
replenishing fluid, make certain that the dipstick cap mental additives. Therefore, do not add any fluid addi-
is reseated properly. tives to the transmission. The only exception to this
policy is the use of special dyes to aid
Fluid and Filter Changes All Wheel Drive (AWD) — If Equipped
Refer to the “Maintenance Schedule” in Section 8 of this Under normal operating conditions, periodic fluid level
manual for the recommended transaxle fluid and filter checks and lubricant changes for the Power Transfer Unit
change intervals. and Rear Carrier, are not required. However when the
vehicle is serviced for other reasons, the exterior surface
If the transaxle is disassembled for any reason, the fluid of these components should be inspected for evidence of
and filter should be changed. fluid leaks. Confirmed leaks should be repaired as soon
as possible.
heavy soil and/or excessive brake dust, use Mopart Your leather upholstery can be best preserved by regular
Wheel Cleaner (05066247AB) or equivalent or select a cleaning with a damp soft cloth. Small particles of dirt
nonabrasive, non-acidic cleaner. Do not use scouring can act as an abrasive and damage the leather upholstery
pads, steel wool, a bristle brush, or metal polishes. Only and should be removed promptly with a damp cloth.
Mopart or equivalent is recommended. Do not use oven Stubborn soils can be removed easily with a soft cloth
cleaner. Avoid automatic car washes that use acidic and Mopar Total Clean. Care should be taken to avoid
solutions or harsh brushes that may damage the wheels’ soaking your leather upholstery with any liquid. Please
protective finish. do not use polishes, oils, cleaning fluids, solvents, deter-
gents, or ammonia based cleaners to clean your leather
Interior Care
upholstery. Application of a leather conditioner is not
Cleaning Interior Trim required to maintain the original condition.
Interior Trim should be cleaned starting with a damp
cloth, a damp cloth with Mopar Total Clean, then Mopar WARNING!
Spot & Stain Remover if absolutely necessary. Do not use
harsh cleaners or Armorall. Use Mopar Total Clean to Do not use volatile solvents for cleaning purposes.
clean vinyl upholstery. Many are potentially flammable, and if used in
closed areas they may cause respiratory harm.
Cleaning Leather Upholstery
Mopar Total Clean is specifically recommended for
leather upholstery.
1. Clean with a wet soft rag. A mild soap solution may be Cleaning The Center Console Cup Holders
used, but do not use high alcohol content or abrasive
Removal
cleaners. If soap is used, wipe clean with a clean damp
Grab the center of the rubber portion of the cupholder
rag.
and lift upward.
2. Dry with a soft tissue.
Cleaning
Seat Belt Maintenance Soak the rubber cupholder liner in a mixture of medium
Do not bleach, dye or clean the belts with chemical hot tap water and one teaspoon of mild liquid dish soap.
solvents or abrasive cleaners. This will weaken the fabric. Let soak for approximately one hour. After one hour pull
Sun damage can also weaken the fabric. the liner from the water and dip it back into the water
about six times. This will loosen any remaining debris.
If the belts need cleaning, use a mild soap solution or
Rinse the liner thoroughly under warm running water.
lukewarm water. Do not remove the belts from the car to
Shake the excess water from the liner and dry the outer
wash them.
surfaces with a clean soft cloth.
Replace the belts if they appear frayed or worn or if the
Installation
buckles do not work properly.
Align the liner in the cupholder and press down firmly.
VEHICLE STORAGE
CAUTION!
If you are leaving your vehicle dormant for more than 21
• When installing the Integrated Power Module days you may want to take steps to protect your battery.
cover, it is important to ensure the cover is prop- You may:
erly positioned and fully latched. Failure to do so • Disconnect the negative cable from the battery.
may allow water to get into the Integrated Power
Module, and possibly result in a electrical system • Anytime you store your vehicle, or keep it out of
failure. service (i.e. vacation) for two weeks or more, run the
air conditioning system at idle for about five minutes
• When replacing a blown fuse, it is important to in the fresh air and high blower setting. This will
use only a fuse having the correct amperage rating. insure adequate system lubrication to minimize the
The use of a fuse with a rating other than indicated possibility of compressor damage when the system is
may result in a dangerous electrical system over- started again.
load. If a properly rated fuse continues to blow, it
indicates a problem in the circuit that must be
corrected.
BULB REPLACEMENT 2. Remove the two screws securing the headlight mod-
ule to the vehicle and gently pull the headlight module
Headlights
forward away from the vehicle, disengaging the assem-
1. Open hood, disconnect and isolate the battery nega- bly from the lower attachment clip.
tive cable.
3. Disconnect the electrical connector.
4. Remove the rubber boot seal.
5. Rotate the bulb to the left and replace the bulb.
Reinstall the rubber boot seal and then the headlight
module.
CAUTION!
High Intensity Discharge Headlights (HID) — If on there is a blue hue to the lights. This diminishes and
Equipped becomes more white after approximately 10 seconds, as
The headlights are a type of high voltage discharge tube. the system charges.
High voltage can remain in the circuit even with the
Front Park/Turn Signal and Sidemarker Lights
headlight switch off and the key removed. Because of
this, you should not attempt to service a headlight bulb 1. Open hood, disconnect and isolate the battery nega-
yourself. If a headlight bulb fails, take your vehicle to tive cable.
an authorized dealer for service.
WARNING!
2. Remove the two screws securing the headlight mod- Front Fog Light
ule to the vehicle and pull the headlight module forward
1. Reach under the front fascia and grasp the front fog
away from the vehicle, disengaging the assembly from
light bulb.
the lower attachment clip.
2. Twist the front fog light bulb to remove from the fog
3. Twist the bulb socket to remove from the headlight
light module.
module and pull the bulb from socket.
3. Disconnect the electrical connector and replace the
4. Replace the bulb, reinstall the socket and then reinstall
bulb.
the headlight module.
CAUTION!
Rear Tail, Stop, Turn Signal, Side Marker and 3. Twist the socket assembly to remove it from the
Back-up Lights housing.
1. Raise the liftgate. 4. Pull the bulb out of the socket.
2. Remove the two tail light assembly screws and rotate 5. Replace the bulb, reinstall the socket, and reattach the
the assembly outward to remove the ball stud form the tail light assembly.
attaching grommet.
License Light
1. Place a screwdriver in the slot next to the release tab
and push on the release tab to remove the lens.
2. Pull the bulb out of the socket. Replace the bulb and
push on the lens until it snaps into place.
7
Chassis
Component Fluids, Lubricants and Genuine Parts
Automatic Transmission Mopart ATF+4 Automatic Transmission Fluid.
AWD Power Transfer Unit Mopart Gear Lubricant 75W-90 or equivalent.
AWD Rear Carrier Mopart Gear Lubricant 75W-90 or equivalent.
Brake Master Cylinder Mopart DOT 3 and SAE J1703 should be used or equivalent. If DOT 3
brake fluid is not available, then DOT 4 is acceptable. Use only recom-
mended brake fluids.
Power Steering Reservoir MopartPower Steering Fluid +4 or MopartATF +4 Automatic Transmis-
sion Fluid.
CONTENTS
m Suggestions For Obtaining Service For Your m Reporting Safety Defects . . . . . . . . . . . . . . . . . . 431
Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 428
▫ In Canada . . . . . . . . . . . . . . . . . . . . . . . . . . 432
▫ Prepare For The Appointment . . . . . . . . . . . . 428
m Publication Order Forms . . . . . . . . . . . . . . . . . . 432
▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 428
m Department Of Transportation Uniform Tire
▫ Be Reasonable With Requests . . . . . . . . . . . . . 428 Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 434
m If You Need Assistance . . . . . . . . . . . . . . . . . . . 428 ▫ Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . . 434
m Warranty Information (U.S. Vehicles Only) . . . . . 431 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . 434
m Mopart Parts . . . . . . . . . . . . . . . . . . . . . . . . . 431 ▫ Temperature Grades . . . . . . . . . . . . . . . . . . . 435 9
technicians, special tools, and the latest information to • Vehicle identification number
assure your vehicle is fixed correctly and in a timely
• Vehicle delivery date and mileage
manner.
DaimlerChrysler Motors Corporation Customer Center
This is why you should always talk to your dealer’s
P.O. Box 21–8004
service manager first. Most matters can be resolved with
Auburn Hills, MI 48321–8004
this process.
Phone: (800) 992-1997
• If for some reason you are still not satisfied, talk to the
DaimlerChrysler Canada Inc. Customer Center
general manager or owner of the dealership. They
P.O. Box 1621
want to know if you need assistance.
Windsor, Ontario N9A 4H6
• If your dealership is unable to resolve the concern, you Phone: (800) 465–2001
may contact the Manufacturer’s Customer Center.
In Mexico contact:
Any communication to the Manufacturer’s Customer Av. Prolongacion Paseo de la Reforma, 1240
Center should include the following information: Sante Fe C.P. 05109
Mexico, D. F.
• Owner’s name and address
In Mexico (915) 729–1248 or 729–1240
• Owner’s telephone number (home and office) Outside Mexico (525) 729–1248 or 729–1240
9
• Dealership name
Customer Assistance For The Hearing Or Speech contract, call the manufacturer’s Service Contract Na-
Impaired (TDD/TTY) tional Customer Hotline at 1-800-521-9922.
To assist customers who have hearing difficulties, the
The manufacturer will not stand behind any service
manufacturer has installed special TDD (Telecommuni-
contract that is not the manufacturer’s Service Contract. It
cation Devices for the Deaf) equipment at its Customer
is not responsible for any service contract other than the
Center. Any hearing or speech impaired customer who
manufacturer’s Service Contract. If you purchased a
has access to a TDD or a conventional teletypewriter
service contract that is not a manufacturer’s Service
(TTY) in the United States can communicate with the
Contract, and you require service after your manufactur-
manufacturer by dialing 1–800–380–CHRY.
er’s new vehicle limited warranty expires, please refer to
Service Contract your contract documents, and contact the person listed in
You may have purchased a service contract for your those documents.
vehicle to help protect you from the high cost of unex-
We appreciate that you have made a major investment
pected repairs after your manufacturer’s new vehicle
when you purchased your new vehicle. Your dealer has
limited warranty expires. The manufacturer stands be-
also made a major investment in facilities, tools, and
hind only the manufacturer’s Service Contracts. If you
training to assure that you are absolutely delighted with
purchased a manufacturer’s Service Contract, you will
your ownership experience. You’ll be pleased with their
receive Plan Provisions and an Owner Identification Card
sincere efforts to resolve any warranty issues or related
in the mail within three weeks of your vehicle delivery
concerns.
date. If you have any questions about your service
MOPART PARTS
WARNING!
Mopart fluids, lubricants, parts, and accessories are
Engine exhaust, some of its constituents, and certain available from your dealer. They will help you keep your
vehicle components contain or emit chemicals vehicle operating at its best.
known to the State of California to cause cancer and REPORTING SAFETY DEFECTS
birth defects or other reproductive harm. In addition,
In the 50 United States and Washington D.C.: If you
certain fluids contained in vehicles and certain prod-
believe that your vehicle has a defect, which could cause
ucts of component wear contain or emit chemicals
a crash or cause injury or death, you should immediately
known to the State of California to cause cancer and
inform the National Highway Traffic Safety Administra-
birth defects or other reproductive harm.
tion (NHTSA) in addition to notifying the manufacturer.
If NHTSA receives similar complaints, it may open an
WARRANTY INFORMATION (U.S. Vehicles Only) investigation, and if it finds that a safety defect exists in
See the Warranty Information Booklet for the terms and a group of vehicles, it may order a recall and remedy
provisions of DaimlerChrysler’s warranties applicable to campaign. However, NHTSA cannot become involved in
this vehicle. individual problems between you, your dealer, and the
manufacturer. 9
To contact NHTSA, you may either call the Auto Safety PUBLICATION ORDER FORMS
Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– To order the following manuals, you may use either the
9153), or go to http://www.safercar.gov; or write to: website or the phone numbers listed below. Visa, Mas-
Administrator, NHTSA, 400 Seventh Street, SW., Wash- tercard, American Express, and Discover orders are ac-
ington, DC 20590. You can also obtain other information cepted. If you prefer mailing your payment, please call
about motor vehicle safety from http:// for an order form.
www.safercar.gov.
NOTE: A street address is required when ordering
In Canada: manuals. (No P.O. Boxes).
If you believe that your vehicle has a safety defect, you
• Service Manuals.
should contact the Customer Service Department imme-
diately. Canadian customers who wish to report a safety These comprehensive service manuals provide the
defect to the Canadian government should write to information that students and professional technicians
Transport Canada, Motor Vehicle Defect Investigations need in diagnosing/troubleshooting, problem solving,
and Recalls, 2780 Sheffield Road, Ottawa, Ontario K1B maintaining, servicing, and repairing DaimlerChrysler
3V9. Corporation vehicles. A complete working knowledge
of the vehicle, system, and/or components is written
in straightforward language with illustrations, dia-
grams, and charts.
DEPARTMENT OF TRANSPORTATION UNIFORM may depart significantly from the norm due to variations
TIRE QUALITY GRADES in driving habits, service practices and differences in road
The following describes the tire grading categories estab- characteristics and climate.
lished by the National highway Traffic Safety Adminis-
Traction Grades
tration. The specific grade rating assigned by the tire’s
The traction grades, from highest to lowest, are AA, A, B,
manufacturer in each category is shown on the sidewall
and C. Those grades represent the tire’s ability to stop on
of the tires on your car.
wet pavement as measured under controlled conditions
All Passenger Car Tires Must Conform to Federal Safety on specified government test surfaces of asphalt and
Requirements in Addition to These Grades. concrete. A tire marked C may have poor traction perfor-
mance.
Treadwear
The treadwear grade is a comparative rating based on the
WARNING!
wear rate of the tire when tested under controlled con-
ditions on a specified government test course. For ex- The traction grade assigned to this tire is based on
ample, a tire graded 150 would wear one and a half (1 straight-ahead braking traction tests, and does not
1/2) times as well on the government course as a tire include acceleration, cornering, hydroplaning, or
graded 100. The relative performance of tires depends peak traction characteristics.
upon the actual conditions of their use, however, and
Temperature Grades
WARNING!
The temperature grades are A (the highest), B, and C,
representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for
and its ability to dissipate heat when tested under a tire that is properly inflated and not overloaded.
controlled conditions on a specified indoor laboratory Excessive speed, under inflation, or excessive load-
test wheel. Sustained high temperature can cause the ing, either separately or in combination, can cause
material of the tire to degenerate and reduce tire life, and heat buildup and possible tire failure.
excessive temperature can lead to sudden tire failure. The
grade C corresponds to a level of performance, which all
passenger car tires must meet under the Federal Motor
Vehicle Safety Standard No. 109. Grades B and A repre-
sent higher levels of performance on the laboratory test
wheel than the minimum required by law.
10