Scribd
Upload
87 views1 page

Schematic

1. The document discusses using a momentary membrane switch to reset a PIC microcontroller and select which waveform from a WaveBank will be activated. 2. It provides instructions for mounting an op-amp in an 8-pin socket to output a 5V peak-to-peak signal with limited bandwidth, or without the op-amp to output an 8.63V peak-to-peak signal. 3. A diagram shows the circuit used for an arbitrary function generator or smart probe head, including the op-amp, resistors, and DIP switch to select the output vector.

Uploaded by

David Torres
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
87 views1 page

Schematic

1. The document discusses using a momentary membrane switch to reset a PIC microcontroller and select which waveform from a WaveBank will be activated. 2. It provides instructions for mounting an op-amp in an 8-pin socket to output a 5V peak-to-peak signal with limited bandwidth, or without the op-amp to output an 8.63V peak-to-peak signal. 3. A diagram shows the circuit used for an arbitrary function generator or smart probe head, including the op-amp, resistors, and DIP switch to select the output vector.

Uploaded by

David Torres
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

1 2 3 4 5 6 7 8 9

F Momentary Membrane switch resets the PIC WaveBank Vector F

This will force WaveBank PIC to vector to 4 Bit binary vector selects which
a location selected by the DIP switch. WaveLoop in WavePOD will be
activated when the PIC is RESET

Mount OP AMP in 8 PIN 300mil IC Socket.

Output with OP-AMP is 5.00V p-p.


The Bandwidth is limited by the OP-AMP characteristics.

Output without OP-AMP is 8.63V p-p.


The Bandwidth is limited by the 3K6 resistor and load capacitance.

VCC

VCC

E E
R12

10K VCC

RESET
R5

4
U3A
TL072 10K Switch
2
R2 R1 R4 R3
1
3 C6 10K 10K 10K 10K

To use as an Arbitrary Function Generator Vector


1nF
plug directly into BitScope. 1 8

8
R10 1K8 2 7
To use as a Smart Probe Head, plug 3 6
into the Smart Cable Assembly. 4 5
D D
SW-DIP4
U3B
TL072
6
GND
7
5

Y1

R11 1K8

20MHz
C1 C2
U1
22pF 22pF
1 18
RA2 RA1
R8 R9 GND GND
2 17
VCC RA3 RA0
3K6 3K6
1 +10V P5
C R6 3 16 C
1 RA4 CLKI
+5 Logic

13
14 1K8
PIC
U2 4 15
2 MCLR CLKO
2 CHAN A
15 4 5
Iout msb-B1 5 14

+Vs
3 6 VSS VDD VCC
3 CHAN B
16F84
BitScope Pod

B2
16 2 7
Iout B3 6 13
IO-1 4 8 RB0 RB7
B4
17 9 C5
B5 7 12
IO-0 5 14 10 RB1 RB6
5 Logic 7 Vrf(+) B6
18 11 GND 100n
B7 8 11
6 15 12 RB2 RB5
6 Logic 6 Vrf(-) lsb-B8
19
9 10
7 16 1 RB3 RB4 GND

-Vs
7 Logic 5 COMPen THRcnt
20 R7
8
8 Logic 4 1K8
21 DAC-0800 PIC16F84
3

9 Logic 3
9 C3
22 GND
B 10 103 B
10 Logic 2 PIC Types
23
GND
11
11 Logic 1 Use any 18pin device which
24
can operate at 20MHz and
12
12 Logic 0 executes 16F84 instructions
25
as a minimum requirement.
13
C4
13 -10V
DB25-F
104

GND

A Metachip Pty Ltd A

Title WavePOD Card Sheet 1 of 1


WavePOD C bitscope
designs A3 Document Number WavePOD-01 Rev 1

Date: 13-Mar-2002 E:\WINDOWS\NJJ\WAVEPOD\WAVEPOD.SCH

1 2 3 4 5 6 7 8 9

You might also like