Lab 6.1.

6 Configuring Static Routes

Objective
• Configure static routes between routers to allow data transfer between routers without the use of
dynamic routing protocols.

Background/Preparation
Setup a network similar to the one in the previous diagram. Any router that meets the interface
requirements may be used. Possible routers include 800, 1600, 1700, 2500, 2600 routers, or a
combination. Refer to the chart at the end of the lab to correctly identify the interface identifiers to be
used based on the equipment in the lab. The configuration output used in this lab is produced from
1721 series routers. Any other router used may produce slightly different output. The following steps
are intended to be executed on each router unless specifically instructed otherwise.
Start a HyperTerminal session as performed in the Establishing a HyperTerminal session lab.
Note: Go to the erase and reload instructions at the end of this lab. Perform those steps on all
routers in this lab assignment before continuing.

Step 1 Configure both routers

a. Enter the global configuration mode and configure the hostname as shown in the chart. Then
configure the console, virtual terminal, and enable passwords. If there are any difficulties, refer to

1-6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 6.1.6 Copyright  2003, Cisco Systems, Inc.
 the Configuring router passwords lab. Configure interfaces and IP host tables. If there are any
difficulties, refer to the Configuring Host Tables lab.

Step 2 Configure the workstations

Configure the workstations with the proper IP address, subnet mask, and default gateway.
a. Check connectivity between the workstations using ping.
C:\>ping 192.168.16.2
Pinging 192.168.16.2 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
Ping statistics for 192.168.16.2:
Packets: Sent = 4, Received = 0, Lost = 4 (100% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms

b. Was the ping successful? __________________________________________________

c. Why did the ping fail? ______________________________________________________

Step 3 Check interface status

a. Check the interfaces on both routers with the command show ip interface brief.
b. Are all the necessary interfaces up? ____________________________________________

Step 4 Check the routing table entries

a. Using the command show ip route, view the IP routing table for GAD.
GAD>show ip route

output eliminated

Gateway of last resort is not set

C 192.168.14.0/24 is directly connected, FastEthernet0

C 192.168.15.0/24 is directly connected, Serial0

b. Use the command show ip route, view the IP routing table for BHM.
BHM>show ip route

Output eliminated.

Gateway of last resort is not set

C 192.168.15.0/24 is directly connected, Serial0

C 192.168.16.0/24 is directly connected, FastEthernet0
c. Are all of the routes needed in the routing tables? __________________________________
d. Can a host on subnet 192.168.16.0 see a host on network 192.168.14.0? _________________
If a route is not in the routers to which the host is connected, the host cannot reach the
destination host.

2-6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 6.1.6 Copyright  2003, Cisco Systems, Inc.
Step 5 Adding static routes
a. How can this situation be changed so that the hosts can ping each other?
Add static routes to each router or run a routing protocol.
b. In global configuration mode, add a static route on Router1 to network 192.168.16.0 and on
Router2 to network 192.168.14.0.
GAD(config)#ip route 192.168.16.0 255.255.255.0 192.168.15.2
BHM(config)#ip route 192.168.14.0 255.255.255.0 192.168.15.1
c. Why is a static route needed on both routers? ___________________________________

Step 6 Verify the new routes

a. Use the command show ip route, view the IP routing table for GAD.

GAD>show ip route

output eliminated

Gateway of last resort is not set

C 192.168.14.0/24 is directly connected, FastEthernet0

C 192.168.15.0/24 is directly connected, Serial0
S 192.168.16.0/24 [1/0] via 192.168.15.2

b. Using the command show ip route, view the IP routing table for BHM.

BHM>show ip route

Output eliminated.

Gateway of last resort is not set

S 192.168.14.0/24 [1/0] via 192.168.15.1

C 192.168.15.0/24 is directly connected, Serial0
C 192.168.16.0/24 is directly connected, FastEthernet0

c. Are all of the routes needed in the routing tables? __________________________________

d. Can a host on subnet 192.168.16.0 see a host on network 192.168.14.0? _________________

Step 7 ping host to host again

a. Check connectivity between the workstations using ping.
C:\>ping 192.168.16.2
Pinging 192.168.16.2 with 32 bytes of data:
Reply from 192.168.16.2: bytes=32 time=20ms TTL=254
Reply from 192.168.16.2: bytes=32 time=20ms TTL=254
Reply from 192.168.16.2: bytes=32 time=20ms TTL=254
Reply from 192.168.16.2: bytes=32 time=20ms TTL=254
Ping statistics for 192.168.16.2:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 20ms, Maximum = 20ms, Average = 20ms

3-6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 6.1.6 Copyright  2003, Cisco Systems, Inc.
 b. If the ping was not successful, check routing table to make sure static routes are entered
correctly.

Upon completion of the previous steps, logoff by typing exit. Turn the router off.

4-6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 6.1.6 Copyright  2003, Cisco Systems, Inc.
Erasing and reloading the router
Enter into the privileged EXEC mode by typing enable.
If prompted for a password, enter class. If “class” does not work, ask the instructor for assistance.
Router>enable
At the privileged EXEC mode, enter the command erase startup-config.
Router#erase startup-config
The responding line prompt will be:
Erasing the nvram filesystem will remove all files! Continue?
[confirm]
Press Enter to confirm.
The response should be:
Erase of nvram: complete
Now at the privileged EXEC mode, enter the command reload.
Router(config)#reload
The responding line prompt will be:
System configuration has been modified. Save? [yes/no]:
Type n and then press Enter.
The responding line prompt will be:
Proceed with reload? [confirm]
Press Enter to confirm.
In the first line of the response will be:
Reload requested by console.
After the router has reloaded the line prompt will be:
Would you like to enter the initial configuration dialog? [yes/no]:
Type n and then press Enter.
The responding line prompt will be:
Press RETURN to get started!
Press Enter.
The router is ready for the assigned lab to be performed.

5-6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 6.1.6 Copyright  2003, Cisco Systems, Inc.
Router Interface Summary
Router Ethernet Ethernet Serial Serial Interface
Model Interface #1 Interface #2 Interface #1 Interface #2 #5
800 (806) Ethernet 0 (E0) Ethernet 1 (E1)
1600 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1)
1700 FastEthernet 0 (FA0) FastEthernet 1 (FA1) Serial 0 (S0) Serial 1 (S1)
2500 Ethernet 0 (E0) Ethernet 1 (E1) Serial 0 (S0) Serial 1 (S1)
2600 FastEthernet 0/0 FastEthernet 0/1 (FA0/1) Serial 0/0 (S0/0) Serial 0/1
(FA0/0) (S0/1)
In order to find out exactly how the router is configured, look at the interfaces. This will identify the type of router
as well as how many interfaces the router has. There is no way to effectively list all of the combinations of
configurations for each router class. What is provided are the identifiers for the possible combinations of interfaces
in the device. This interface chart does not include any other type of interface even though a specific router may
contain one. An example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation
that can be used in IOS command to represent the interface.

6-6 CCNA 2: Routers and Routing Basics v 3.0 - Lab 6.1.6 Copyright  2003, Cisco Systems, Inc.