Scribd Logo
Upload

Welcome to Scribd!

  • 72 views

    02 - SIM DN150 PN160 Valve 2 PDF

    Uploaded by

    unnicyriac
    1. This document provides sizing information for a control valve with a 150mm diameter and 160PN rating located at Jabal Hafeet. It analyzes the valve's performance under high and low flow conditions. 2. Charts are included showing the valve's head loss coefficient, Kv value, and cavitation index over a range of opening positions. The head loss and Kv value charts can be used to calculate flow rate and pressure drop through the valve. 3. An orifice system is used downstream of the valve to build backpressure and create favorable operating conditions. The downstream pressure indicated assumes a specific orifice unit pressure of 0.16 bar.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    02 - SIM DN150 PN160 Valve 2 PDF

    Uploaded by

    unnicyriac
    72 views4 pages
    1. This document provides sizing information for a control valve with a 150mm diameter and 160PN rating located at Jabal Hafeet. It analyzes the valve's performance under high and low flow conditions. 2. Charts are included showing the valve's head loss coefficient, Kv value, and cavitation index over a range of opening positions. The head loss and Kv value charts can be used to calculate flow rate and pressure drop through the valve. 3. An orifice system is used downstream of the valve to build backpressure and create favorable operating conditions. The downstream pressure indicated assumes a specific orifice unit pressure of 0.16 bar.

    Original Title

    02 - SIM DN150 PN160 Valve 2.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. This document provides sizing information for a control valve with a 150mm diameter and 160PN rating located at Jabal Hafeet. It analyzes the valve's performance under high and low flow conditions. 2. Charts are included showing the valve's head loss coefficient, Kv value, and cavitation index over a range of opening positions. The head loss and Kv value charts can be used to calculate flow rate and pressure drop through the valve. 3. An orifice system is used downstream of the valve to build backpressure and create favorable operating conditions. The downstream pressure indicated assumes a specific orifice unit pressure of 0.16 bar.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    72 views4 pages

    02 - SIM DN150 PN160 Valve 2 PDF

    Uploaded by

    unnicyriac
    1. This document provides sizing information for a control valve with a 150mm diameter and 160PN rating located at Jabal Hafeet. It analyzes the valve's performance under high and low flow conditions. 2. Charts are included showing the valve's head loss coefficient, Kv value, and cavitation index over a range of opening positions. The head loss and Kv value charts can be used to calculate flow rate and pressure drop through the valve. 3. An orifice system is used downstream of the valve to build backpressure and create favorable operating conditions. The downstream pressure indicated assumes a specific orifice unit pressure of 0.16 bar.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    1

    100 Control valve sizing program

    Project Name: Jabal Hafeet Valve 2


    Description/function: 0
    Location: 0
    Item Name: Control valve @
    Opp. Number CRM 55235
    Date: Nov. 12th 2020
    Rev.: 0

    Total dynamic head Total dynamic opening Pos.


    Q_FCV [m³/h]
    (bar) at the valve's head (bar) at the [%] from valve v_DN FCV
    Condition (name/number)
    inlet valve's outlet piston [m/s]
    P1 P2 movement
    high flow condition 90 85,8 40,2 54,00 1,4
    low flow condition 43,2 98,1 9,6 26,00 0,7

    Valve DN 150
    Valve PN 160
    Insert type Customized
    orifice unit Needed

    All used heads are considered to be dynamic ones. We kindly encourage the hydraulic designers to check the correctness of the
    used data and comment or confirm them. If heads measured on site differ from those simulated the performance of the valve will
    be affected. Maximum flow may not be achieved, cavitation may be encountered.
    This solution adopts an orifice system downstream of the valve. The orifice system builds up pressure to create
    favorable conditions for the control valve. P2 indicated in this simulation resembles the backpressure created by the
    orifice unit. The downstream pressure of the orifice unit (P3) is the pressure available in the system. and te one
    provided in your data sheet.
    In this case of high flow P3 = 0,16 bar

    ]
    This chart is only valid for cavitation free operation.

    Zeta curve

    10000000
    100

    1000000

    100000

    10000
    Zeta

    1000

    100

    10

    1
    0 10 20 30 40 50 60 70 80 90 100
    Opening degree [%]

    The head loss of a valve can be calculated by means of following relation:

    v2
    Dp  z  r 
    2
    Dp ... head loss [Pa] (10 5 Pa = 1 bar)
    z ... head loss coefficient (without dimensions)
    r ... density of liquid [kg/m³]
    v ... average flow velocity [m/s]
    (referred to the valve size)
    Name KM Zeichnungsnummer

    Meßfile
    Jabal Hafeet Valve 2

    erstellt Valve DN150Valve PN160


    Datum Nov. 12th 2020 head loss coefficient diagram
    Rev. 0 fitted in a horizontal pipe
    Proprietary notice
    ERHARD GmbH&Co.KG • Postfach 1280 • 89502 Heidenheim pursuant to ISO 16016 to
    be observed

    ]
    This chart is only valid for cavitation free operation.

    Kv curve
    35 553

    30

    25
    kv value [m³/h]

    20

    15

    10

    0
    0 10 20 30 40 50 60 70 80 90 100
    Opening degree [%]

    The kv value describes the water flow rate in m³/h at a temperature


    of 5° to 30° C and with a pressure loss of 1 bar.
    The relation between kv and the flow rate Q is:

    Dp
    Q  kv 
    10  r  g

    Dp ... pressure loss [Pa] (10 5 Pa = 1 bar)


    r ... density of the medium [kg/m³]
    g ... acceleration of the gravity [m/s²] (g = 9,81 m/s²)

    Name KM Zeichnungsnummer

    Meßfile
    Jabal Hafeet Valve 2

    erstellt Valve DN150Valve PN160


    Datum Nov. 12th 2020 Kv-value
    Rev. 0 fitted in a horizontal pipe
    Proprietary notice
    ERHARD GmbH&Co.KG • Postfach 1280 • 89502 Heidenheim pursuant to ISO 16016 to
    be observed

    ]
    This chart is only valid for cavitation free operation.

    Operation limit and cavitation index

    1,00

    0,10
    Sigma values

    0,01

    0,00
    0 10 20 30 40 50 60 70 80 90 100

    Opening degree [%]

    Sigma_Ph FCV[-] = (Pb + Patm-Pvapour) X 100000/((Pa-Pc)x100000 + V2 x ρ/2)

       Sigma_Ph FCV[-] is the calculated sigma value corresponding to


    the relevant operating conditions.
       Pa = inlet pressure; , Pb = intermediate pressure in the valve; and Pc = outlet pressure
       Patm : is the atmospheric pressure = 1 bar
       Pvapor: is the water vapor pressure = 0,032 bar
       V : is the mean velocity ( m/sec) in the pipe just before the control valve
       Ρ: is the density of water in kg/m3

    Name KM Zeichnungsnummer

    Meßfile
    Jabal Hafeet Valve 2

    erstellt Valve DN150Valve PN160


    Datum Nov. 12th 2020 Operation limit curve showing Sigma points
    Rev. 0 fitted in a horizontal pipe
    Proprietary notice
    ERHARD GmbH&Co.KG • Postfach 1280 • 89502 Heidenheim pursuant to ISO 16016 to
    be observed

    You might also like