Scribd
Upload
60 views2 pages

Counters Controllers Encoders

This document summarizes the specifications of an incremental encoder with a hollow shaft. It can operate at speeds up to 12,000 RPM with resolutions up to 2048 pulses. It has electrical outputs of either 5 VDC line driver or 10-30 VDC push-pull and is protected against vibration, shock, and interference. Connection and mounting details are provided along with cutout dimensions.

Uploaded by

Alexandru Budu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
60 views2 pages

Counters Controllers Encoders

This document summarizes the specifications of an incremental encoder with a hollow shaft. It can operate at speeds up to 12,000 RPM with resolutions up to 2048 pulses. It has electrical outputs of either 5 VDC line driver or 10-30 VDC push-pull and is protected against vibration, shock, and interference. Connection and mounting details are provided along with cutout dimensions.

Uploaded by

Alexandru Budu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

GI338

COUNTERS CONTROLLERS ENCODERS

Incremental Encoder with


hollow shaft
Features

Incremental encoder with integrated OPTO-ASIC, thus high


interference immunity
Speed up to 12,000 RPM
Resolution up to 2048 pulses

Electrical data

Supply voltage 5 VDC ± 10 % and 10...30 VDC


Current consumption 60 mA (without load)
Scanning frequency 50 kHz (< 500 pulses)
100 kHz (> 500 pulses)
Output stages
Output signals 5 VDC Line driver to RS422
10...30 VDC Push-pull output,
Signals with clockwise sense of rotation when looking at short-circuit-protected
the flange Electric connector The electric connector must not be
plugged on or removed whilst under
Signal outputs 5 VDC line driver voltage

Track A
Mechanical data
Track A
RPM value Max. 12,000 RPM
Track B
Operating torque < 0.21 Ncm (3,000 RPM / 20 °C)
Track B Material
Flange Aluminum
Zero pulse Housing Black Polyamide
Shaft Stainless steel
Zero pulse Weight Approximately 85 g

Signal outputs 10...30 VDC


Ambient conditions

Track A Ambient temperature -20...+85 °C


Protection to
Track B Shaft IP 64 ball bearing with seals
Housing IP 43 through shaft
Zero pulse IP 65 with sealing cover
Relative humidity Max. 95 %, non-condensing
Endurance
Vibration IEC 68, Section 2 - 6
< 100 m/s2 /10-200 Hz
Shock IEC 68, Section 2 - 27
< 500 m/s2 / 11 ms
Interference immunity EN 50082-2
EN 61000-4 -2 to 4 Severity grade 3
Emitted interference EN 50081-2

1
IVO GmbH & Co. Printed in Germany 07.01
P.O. Box 3360 • D-78022 Villingen-Schwenningen IVO GmbH & Co. 170.02.182/5
Phone +49 (0)7720 942-0 • Fax +49 (0)7720 942-999
www.ivo.de • e-mail: [email protected]
GI338

Order designation Pin assignment

Order Hollow shaft „Line driver 5 VDC“

0 Bore 6 mm / Torque support Cable color Assignment


1 Bore 6 mm / Spring plate
brown UB
green Track A
Voltage / Signals
red Track A inv.
22 5 VDC line driver RS422 yellow Track B
60 10...30 VDC push-pull output blue Track B inv.
pink Track N (zero pulse)
Connection gray Track N inv. (zero pulse inv.)
white GND
41 Cable 1 m, radial
Cable shield Shield connected to flange
Further cable lengths upon request

Pulse no. / Order no. „Push-pull output 10...30 VDC“

Pulse no. Pulse no. Cable color Assignment


5 49 400 14 brown UB
50 39 500 15 green Track A
60 40 1000 22 yellow Track B
100 41 1024 23 pink Track N (zero pulse)
200 06 2000 28 white GND
250 09 2048 29 Cable shield Shield connected to flange
360 13
Recommendation: Please use leads twisted in pairs for
Further pulse versions upon request cable lengths of more than 10 m

GI338.

Dimensions and cutout size

12 33.5 33.5
Straight 9 ±1 12-21
pin 6.5 2.4 6 Tk ø 45
ø 3 x 16
R 15 ±3

ø 6H7 x 19.5
ø16

ø 3.5
8.5

8.5

1 0.5
5.5 40 5.5
6.5 6.5
27 27
32.5 32.5

2
Subject to modification in technic and design.
Errors and omissions excepted.

You might also like