REVISIONS

SPECIFICATIONS DESCRIPTION

ECN NO
LETTER
MODEL: 201.60 DRAWN ENGR DATE

STROKE: 20 in [508 mm]

ROD DIAMETER: 6.000 in [152.40 mm]

PISTON AREA: TENSION: 50.27 in² [324.3 cm²]

COMPRESSION: 78.54 in² [506.7 cm²]

STATIC TENSION FORCE RATING: 146 kip [648 kN]

AT 3000 psi [207 bar]
SYSTEM STATIC PRESSURE

STATIC COMPRESSION FORCE RATING: 228 kip [1013 kN]

AT 3000 psi [207 bar]
SYSTEM STATIC PRESSURE 88.05 [2236.5] MINIMUM EXTENSION
9.50 98.05 [2490.5] MID STROKE
241.3 108.05 [2744.5] MAXIMUM EXTENSION 9.50
241.3
PRESSURE
-16 37° FLARE
P R DRAIN
-06 37° FLARE

D RETURN 1.77
-16 37° FLARE 45
HYDRAULIC SCHEMATIC
21.50 7.88 33.65 2.50 12.00 25.75
546.1 200.2 854.7 63.5 304.8 654.1

15.76 13 6 13
400.3 12.30 7 5 4 5 7
2 2 2
312.4
11.75
298.4 4X 1.720 THRU
43.7

13.09
332.5

11.75 16.00
298.5 406.4

9.00
228.6

SWIVEL MOUNTING -
PATTERN SOURCE/REF
DRAWING 100-323-489
TYPICAL BOTH ENDS
12 12 PROPRIETARY DATA
NOTES: 2 3 3 1 4 11 6 7 8 9 10 THE INFORMATION AND DESIGN(S)
2 2 DISCLOSED HEREIN ARE CONFIDENTIAL
AND THE PROPERTY OF MTS SYSTEMS
1. UNLESS OTHERWISE SPECIFIED, ALL DIMENSIONS INCH [MILLIMETERS] AND CORPORATION AND MAY NOT BE USED,
WEIGHTS LBS [KG] ARE SHOWN FOR REFERENCE ONLY. REPRODUCED OR DISCLOSED IN ANY
FORM EXCEPT AS GRANTED IN WRITING
BY MTS SYSTEMS CORPORATION. THIS
RESTRICTION EXCLUDES INFORMATION
2. REFERENCE CYLINDER ASSEMBLY FOR ASSEMBLY AND TEST PROCEDURES. THAT IS IN THE PUBLIC DOMAIN OR
WAS LEGITIMATELY IN THE PRIOR
POSSESSION OF THE RECIPIENT.
UNLESS OTHERWISE SPECIFIED
3 LUBE AND TORQUE 1-8UNC TO 680 LB-FT [920 N-M]. MATERIAL DESCRIPTION .XXX HOLE SIZE TOLERANCE DRAWN CHECK ENGR MFG
----- CDB - FRM -
0.000 OVER .750
DATE
4 LUBE AND TORQUE 3/8-16UNC TO 34 LB-FT [47 N-M]. MATERIAL SIZE TO .750
+.010/-.002
TO 1.500
+.015/-.003
DATE DATE DATE

----- 11-09-15 - 11-15 -

FINISH MASK ANGLE 2 TITLE
5 LUBE AND TORQUE 5/16-18UNC TO 19 LB-FT [26 N-M].

TOLERANCES
----- M X 1/4 ACT ASSY-(M),201.60,

GENERAL
Y
THREAD DEPTHS ARE TO MIN FULL THDS SCALE .X .1
500MM, DUAL 252.25
6 LUBE AND TORQUE 1/4-20UNC TO 6.7 LB-FT [9.1 N-M]. DRILL DEPTHS ARE TO FULL DIA NONE
.03
.XX NEXT LEVEL SIZE NUMBER REV
REMOVE BURRS AND SHARP EDGES MACHINED
SURFACES 201.60
100-324-174 A
DO NOT SCALE PRINT .XXX .010
D
180
7 TORQUE TO MANUFACTURER'S SPECIFICATION (STAMPED ON PART). MTS SYSTEMS CORPORATION THIRD PRODUCT CODE
m EDEN PRAIRIE, MINNESOTA U.S.A.
ANGLE
----- SHEET 1 OF 1
C
PROJ