Search...

 Home
 Valve
 Piping Components
 Piping layout
o PDMS
 Pipe fittings
 How To
 Checklists
 Forum
 Submit your post

Go to...
Home » Introduction » Types of Loads Considered for Piping Stress Analysis

Types of Loads Considered for Piping

Stress Analysis
2 Comments

Every Piping system is subjected to different loads during its design life which develops stresses in the system. Depending on the stress
design basis the system is classified as stress critical or non- stress critical. All the stress critical system shall be stress analyzed using
software system (eg.Caesar II) to keep the stresses within the allowable limits as per the code/standard. The types of loads to be
considered in Stress Analysis shall be as given in table:

Types of Loads:

a) Thermal Loads at Various Operating Conditions

b) Sustained Loads
c) Seismic Loads
d) Wind Loads
e) PSV Reaction Force
f) Slug Force
g) Forces Induced by Surge Pressure

a) Thermal Loads at Various Operating Conditions

Analysis Temperature and Pressure to be used shall be as mentioned below.

Analysis Temperature

Normally the Design temperature (Maximum/ Minimum values as per Line List) shall be used for thermal analysis.

For those lines having Design temperature greater than 80 deg. C and if the difference between Operating and Design temperature is
more than 25 deg. C, the maximum/minimum Operating temperatures, as obtained from Process Group, may be used in Stress
Analysis in place of the Design temperature.
In addition to the Maximum/Minimum Design/Operating temperatures, Piping shall also be analyzed for the Normal Operating
temperature.

Analysis Pressure

Line Design Pressure specified in the Line List shall be considered as the analysis pressure.

b) Sustained Loads
Sustained loads to be considered are as given below:

 Design pressure.

 Weight of Pipe and associated components such as Flanges, Valves, Strainer,

 Sight glass etc., mounted on the Piping System.

 Weight of Fluid/contents in the piping.

 Insulation and cladding weight.

 Hydro test loads, if applicable for the line.

 Snow load, if applicable.

c) Seismic Loads
For Projects where Seismic Design is to be carried out, equivalent Static Seismic Analysis method in Caesar II shall be used to evaluate
the seismic stresses, displacements and loads on the piping system.

If the Seismic coefficient is not provide by the client, then the calculation of static seismic co-efficient in terms of ‘g’ based on Project
site-specific data shall be calculated as per relevant codes (UBC/ASCE/SNIP/others as applicable). In that case, the Seismic factor
calculation document shall be enclosed as an Attachment to the Project Stress Analysis Design basis document.

The normal Operating Temperature shall be used when analyzing for Occasional loads. Seismic loads shall be considered as acting
along the horizontal axes (both in +ve and in the –ve directions, that is, along North, South, East and West directions), but not acting
simultaneously.

d) Wind Loads
Wind loads shall be considered for lines with outside diameter 14” NB (including insulation) & above and at Elevation 10 meters &
above from ground level. The normal Operating Temperature shall be used when analyzing for Occasional loads.

Wind shape factor shall be considered as 0.7. Wind loads shall be considered as acting along the horizontal axes (both in the +ve and
in the –ve directions, that is, along North, South, East and West directions), but not acting simultaneously.

Wind pressure for the different Elevations shall be specific to the Project as per the Project Civil/Structural design basis. The same shall
be considered for wind data input in piping analysis.

e) PSV Reaction Force

If the Piping System being analyzed consists of PSV (pressure safety valve), the reaction force due to PSV operation shall be
considered as applicable and a static equivalent method of stress analysis shall be performed considering the same.

A Dynamic Load Factor equal to 2.0 shall be applied on the valve reaction force value. However, in the case of valves of high reaction
force values, the DLF value calculated as per appendix-II of ASME B31.1 may be used, based on valve data if provided by Vendor.

f) Slug Force
For lines having slug flow regime, as identified by the Process group on P&ID/line list, slug force shall be considered in the piping stress
analysis. Slug force shall be calculated as below:

Fslug = (ρ) (A) (V2) [2(1 – cos θ)]1/2 DLF

Where,

Fslug = Force due to slug in Newton.

ρ = Density of the slug in Kg/m3,

A = Inside area of pipe cross section in m2,

V = Velocity of moving slug in m/sec.

θ = inclusion angle at elbow or change of direction

DLF = Dynamic Load Factor (DLF) equal to two shall be used, unless more accurate value is available.

Fig1: Forces at a 90° bend (or 90° change in direction or at intersection)

Faxial = (ρ) (A) (V2) DLF

Forthogonal = (ρ) (A) (V2) DLF

Slug properties shall be obtained from Process group.

Equivalent static analysis in Caesar-II shall be performed to simulate slug loading in piping system, with the slug force calculated as
above.

g) Forces Induced by Surge Pressure

The effect of surge on any line, as identified by the Process group or a specialist agency, shall be considered in piping analysis.

However two concurrent occasional loadings need not to be considered in piping stress analysis.

Share this on WhatsApp

MORE READ
 Hazardous Area Classification
July 17, 2017

Different Steam Trap Arrangements on Steam Headers in Piping System

July 13, 2017

Piping Stress Critical Linelist: Format and Use, Responsibilities and Method
of Operation
July 12, 2017

2 COMMENTS

1.

Matteo

May 26, 2015 at 8:07 am

Dear Sirs,
concerning the wind loads, I would like to know the references of the exclusion indicated above in the page.
Are them taken from ASME or are just a “good practice”?

Thanks

Reply

Piping engineering

August 21, 2015 at 7:39 pm

Hi Mattero,
Wind loads are mostly provided by the client in the meta ocean/geo technical report or structural design basis.

Reply

LEAVE A REPLY

Your email address will not be published. Required fields are marked *
Comment

Name *

Email *

Check here to Subscribe to notifications for new posts

Post Comment

Confirm you are NOT a spammer

you MUST enable javascript to be able to comment <input type="hidden" name="JS04X7" value="NS1" /> <p><strong>Currently you
have JavaScript disabled. In order to post comments, please make sure JavaScript and Cookies are enabled, and reload the
page.</strong> <a href="http://enable-javascript.com/" rel="nofollow external" >Click here for instructions on how to enable JavaScript in
your browser.</a></p>

to search type and hi

FOLLOW US ON GOOGLE+

Subscribe Updates. It's Free!

Your email:

Subscribe

http://
Leave Blank: Don't Change:

 Popular
 Recent
 Comments

 Piping Layout Drawings Abbreviations and Legends

July 12, 2017

 Nozzle Orientation Drawing

July 12, 2017

 Centrifugal Pump Piping Design Layout

July 12, 2017

  Tank farm: Types, Design Considerations, Plot Plan Arrangement,
Dyke Enclosure- Part 1

July 12, 2017

7 Excel Functions You Must Know to Work Smarter

July 12, 2017

Or reach me on [email protected]

Google+

© copyright Piping-engineering 2017 All Rights Reserved. Privacy Policy | About Us