F A A d rl π π d rl: Visit us at: www.nodia.co.in

Download as pdf or txt
Download as pdf or txt
You are on page 1of 3

www.gatehelp.

com

CHAP 7 HEAT TRANSFER PAGE 335

F11 = 1 − A2 = 1 − 2πr22l = 1 − 2r22l


A1 πd 1 d1
= 1 − 2 # 0.250 # 0.5 = 1 − 1 = 0.75
12 4

SOL 7.34 Option (D) is correct.


The figure shown below are of parallel flow and counter flow respectively.

For parallel flow,


th1 = 80cC , th2 = 50cC , tc1 = 30cC , tc2 = 40cC
(t − t ) − (th2 − tc2)
θmp = θ1 − θ2 = h1 c1
ln b θ1 l ln b th1 − tc1 l
θ2 th2 − tc2
Where, θmp denotes the LMTD for parallel flow.
(80 − 30) − (50 − 40)
θmp = = 40 = 24.85c C
ln b l
50 ln (5)
10
For counter flow arrangement
th1 = 80cC , th2 = 50cC , tc1 = 40cC , tc2 = 30cC
Where, θmc denotes the LMTD for counter flow.

(t − t ) − (th2 − tc1)
θmc = θ1 − θ2 = h1 c2
θ
ln b l
1
ln b th1 − tc2 l
θ2 th2 − tc1
(80 − 30) − (50 − 40)
= = 40 = 28.85cC
ln b l
50 ln (5)
10
Now for defining the type of flow, we use the correction factor.
θm = Fθmc = Fθmp ...(i)
Where F = correction factor, which depends on the geometry of the heat
exchanger and the inlet and outlet temperatures of the of the hot and cold
streams.
GATE Previous Year Solved Paper For Mechanical Engineering
Published by: NODIA and COMPANY ISBN: 9788192276250
Visit us at: www.nodia.co.in
www.gatehelp.com

PAGE 336 HEAT TRANSFER CHAP 7

F < 1, for cross flow and F = 1, for counter and parallel flow
So, From equation (i),
F = θm = 26 = 0.90 < 1
θmc 28.85
and also F = θm = 26 = 1.04 > 1
θmp 24.85
So, cross flow in better for this problem.

SOL 7.35 Option (C) is correct.


Given : A duct of rectangular cross section. For which sides are
a = 1 m and b = 0.5 m
T1 = 30cC , T2 = 20cC , V = 10 m/ sec , k = 0.025 W/m K
Viscosity = 18 μPas , Pr = 0.73 , ρ = 1.2 kg/m3 , Nu = 0.023 Re0.8 Pr0.33
Hence, For a rectangular conduit of sides a and b,
Hydraulic diameter, DH = 4A
p
Where, A is the flow cross sectional area and p the wetted perimeter
DH = 4ab = 2ab
2 (a + b) (a + b)
= 2 # 1 # 0.5 = 1 = 0.666 m
(1 + 0.5) 1.5
ρVDH
Reynolds Number, Re =
μ
= 1.2 # 10 # −06.666 = 4.44 # 105
18 # 10

SOL 7.36 Option (D) is correct.


From the first part of the question,
Re = 4.44 # 105
Which is greater than 3 # 105 . So, flow is turbulent flow.
Therefore, Nu = 0.023 Re0.8 Pr0.33
^ h #
hL = 0.023 4.44 105 0.8 (0.73) 0.33 Nu = hL
k # k
= 0.023 # 32954 # 0.9013 = 683.133
h = 683.133 # k
L
= 683.133 # 0.025 = 25.64 W/m2 K
0.666
DH = L = 0.666 m

Total Area, A = 2 (a + b) L = 2 (1 + 0.5) L = 3L


Heat transfer by convection is given by,
Q = hA (T1 − T2)
GATE Previous Year Solved Paper For Mechanical Engineering
Published by: NODIA and COMPANY ISBN: 9788192276250
Visit us at: www.nodia.co.in
www.gatehelp.com

CHAP 7 HEAT TRANSFER PAGE 337

= 25.64 # 3L # [(273 + 30) − (273 + 20)]


Heat transfer per meter length of the duct is given by
Q
= 25.64 # 3 # 10 = 769.2 W - 769 W
L

SOL 7.37 Option (B) is correct.


The one dimensional time dependent heat conduction equation can be
written more compactly as a simple equation,
1 2 rn 2T + q = ρc 2T
rn 2r : 2r D k
...(i)
k 2t
Where, n = 0 , For rectangular coordinates
n = 1, For cylindrical coordinates
n = 2 , For spherical coordinates
Further, while using rectangular coordinates it is customary to replace the
r -variable by the x -variable.
For sphere, substitute r = 2 in equation (i)
1 2 r22T + q = ρc 2T
r22r : 2r D k k 2t
1 2 r22T + q = 1 2T α = k = thermal diffusivity
r22r : 2r D k α 2t ρc

SOL 7.38 Option (C) is correct.

Let Length of the tube = l


Given : r1 = d1 = 2/2 cm = 1 cm , r2 = 5 cm = 2.5 cm
2 2
Radius of asbestos surface, r3 = d2 + 3 = 2.5 + 3 = 5.5 cm
2
ks = 19 W/mK , ka = 0.2 W/mK
And T1 − T2 = 600c C
From the given diagram heat is transferred from r1 to r2 and from r2 to r3 .
So Equivalent thermal resistance,
loge (r2 /r1)
ΣR = 1 ln a r2 k + 1 ln a r3 k For hollow cylinder Rt =
2πks l r1 2πka l r2 2πkl
GATE Previous Year Solved Paper For Mechanical Engineering
Published by: NODIA and COMPANY ISBN: 9788192276250
Visit us at: www.nodia.co.in

You might also like