Scribd
Upload
239 views14 pages

Sample Calculation-B

This document contains solutions to three problems involving steam power plants operating on different Rankine cycles. Problem 1 involves a reheat Rankine cycle and calculates the pressure required for reheating steam and the cycle efficiency. Problem 2 involves a regenerative Rankine cycle with one open feedwater heater and calculates the steam extraction fraction and cycle efficiency. Problem 3 involves a regenerative Rankine cycle with two closed feedwater heaters, calculates the cycle efficiency and mass flow rates into the feedwater heaters.

Uploaded by

Edrielle
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
239 views14 pages

Sample Calculation-B

This document contains solutions to three problems involving steam power plants operating on different Rankine cycles. Problem 1 involves a reheat Rankine cycle and calculates the pressure required for reheating steam and the cycle efficiency. Problem 2 involves a regenerative Rankine cycle with one open feedwater heater and calculates the steam extraction fraction and cycle efficiency. Problem 3 involves a regenerative Rankine cycle with two closed feedwater heaters, calculates the cycle efficiency and mass flow rates into the feedwater heaters.

Uploaded by

Edrielle
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 14

Problem 1: Reheat Rankine cycle

Consider a steam power plant operating on the ideal reheat Rankine cycle.
Steam enters the high-pressure turbine at 15 MPa and 600°C and is
condensed in the condenser at a pressure of 10 kPa. If the moisture content
of the steam at the exit of the low-pressure turbine is not to exceed 10.4
percent, determine (a) the pressure at which the steam should be reheated
and (b) the thermal efficiency of the cycle. Assume the steam is reheated to
the inlet temperature of the high-pressure turbine.

SOLUTION:
Problem 2: Regenerative Cycle
Consider a steam power plant operating on the ideal regenerative Rankine
cycle with one open feedwater heater. Steam enters the turbine at 15 MPa
and 600°C and is condensed in the condenser at a pressure of 10 kPa. Some
steam leaves the turbine at a pressure of 1.2 MPa and enters the open
feedwater heater. Determine the fraction of steam extracted from the turbine
and the thermal efficiency of the cycle.
SOLUTION:
34
Problem 3: Regenerative with close feedwater heater

Consider a steam power plant operating on the ideal regenerative Rankine


cycle with two closed feedwater heater. Steam enters the turbine at 15 MPa
and 600°C and is condensed in the condenser at a pressure of 10 kPa. Some
steam leaves the turbine at a pressure of 4 MPa and 0.5 MPa enters the
closed feedwater heater respectively. Determine the thermal efficiency of the
cycle and mass flow rate of steam entering the two closed FWH.
SOLUTION:
 State 1 pump : P1 = 10 kPa h1 = hf@P1 = 191.81 kJ/kg
3
saturated liquid v1=vf@P1 = 0.00101 m /kg
s1= 0.6492 kJ/kg K

 State 2 : p2 = p5 = 15 MPa
s2 = s1
Wpump= v1(P2 - P1)= 0.00101 (15000 - 10)
= 15.14 kJ/kg
h2=h1 + Wpump
= 191.81+ 15.14 = 206.95 kJ/kg

State 5: p5 = 15 MPa h5 = 3582.3 kJ/kg


Ts = 600ºC s5 = 6.6775 kJ/kg . K

s5 = s6 = s7 = s8

 State 6: p6 = 4 MPa h6 = 3152 kJ/kg


s6 = 6.6775 kJ/kg . K T6 = 375 ºC

 State 7: p7 = 0.5 MPa hf = h11 = 640.21 kJ/kg


s7 = 6.6775 kJ/kg . K hfg = 2108.47 kJ/kg
mixture sf = 1.8606 kJ/kg . K
sfg = 4.9606 kJ/kg . K

43
s7 s
6.6775  1.8606
f 
x7  4.9606
s fg

x7 0.971
h7= hf + x7 hfg= 640.21 + 0.971* 2108.47

h7=2687.5 kJ/kg

 State 8: p8 = 10 kPa hf = 191.81 kJ/kg


s8 = s7 = 6.6775 kJ/kg . K hfg = 2392.82 kJ/kg
mixture sf = 0.6492 kJ/kg . K
sfg = 7.501 kJ/kg . K

s8 s
f 6.6775 0.6492
x8   7.501
s fg

x8 0.803
h8= hf + x8 hfg= 191.81 + 0.803* 2392.82
h8=2113.2 kJ/kg

State 9: p9 = 4 MPa h9 = 1087.29 kJ/kg


Sat. T9 = 250.4 ºC

 State 3: Assume TTD = 2 ºC


TTD = T11 - T3 (T11 = Tsat, 500 kPa.)
2 = 151.86 - T3
T3 = 149.86 ºC T3 ≈ 150 ºC
at T3 = 150 ºC h3 = hf = 632.18 kJ/kg

 State 4: Assume TTD = 2 ºC


TTD = T9 - T4 (T9 = Tsat, 4MPa.)
2 = 250.4 – T4
T4 = 248.4 ºC T4 ≈ 248 ºC
at T4 = 248 ºC h4 = hf = 1074 kJ/kg

The energy balance on the high pressure FWH is given as :

Energy entering regenerator = Energy leaving regenerator


m1 h6 + h3 = m1h9 + h4 m1 (h6 - h9) = h4 - h3
m1 (3152 – 1087.29) = 1074 – 632.18
m1 = 0.214 kg
The energy balance on the low pressure FWH is given as :

Energy entering regenerator = Energy leaving regenerator


m1 h10 + m2 h7 + h2 = (m1+ m2) h11 + h3
m1 (h10 - h11) + m2 (h7 - h11) = h3 - h2

at throttling process is a constant enthalpy process , so that:


h9 = h10
h11 = h12
h11 = hsat, 500 kPa = 640.21 kJ/kg

0.214(1087.29 - 640.21) + m2(2687.5 - 640.21) = 632.18 - 206.95 m2 = 0.161 kg

qi
n h5 h4 qin 3582.3 1074

qin 2508.3kJ / kg
qou
t
1m1 m2 h8 h1  m1 m2 h12 h1 

qou 10.214 0.1612113.2 191.81 0.214 0.161640.21191.81


t 1369kJ / kg
qou
t

W
 qnet 1qout
in qin
1369
1  2508.3

0.454 45.4%

48

You might also like