SSC-JE

Staff Selection Commission

Junior Engineer
Electrical Engineering
Conventional Solved Questions
Previous Years Solved Papers
(2007–2019)

Also useful for State Service Examinations

and other Competitive Examinations

Publications

www.madeeasypublications.org
 Publications

MADE EASY Publications

Corporate Office: 44-A/4, Kalu Sarai (Near Hauz Khas Metro Station), New Delhi-110016
E-mail: [email protected]
Contact: 011-45124660, 08860378007
Visit us at: www.madeeasypublications.org

SSC-Junior Engineer : Electrical Engineering Previous Year Conventional Solved Papers

Copyright © by MADE EASY Publications.
All rights are reserved. No part of this publication may be reproduced, stored in or introduced into a retrieval
system, or transmitted in any form or by any means (electronic, mechanical, photo-copying, recording or
otherwise), without the prior written permission of the above mentioned publisher of this book.

First Edition: 2016

Second Edition: 2018
Third Edition: 2019
Fourth Edition: 2020

MADE EASY PUBLICATIONS has taken due care in collecting the data and providing the solutions, before publishing this book.
Inspite of this, if any inaccuracy or printing error occurs then MADE EASY PUBLICATIONS owes no responsibility. MADE EASY
PUBLICATIONS will be grateful if you could point out any such error. Your suggestions will be appreciated.

© All rights reserved by MADE EASY PUBLICATIONS. No part of this book may be reproduced or utilized in any form without the
written permission from the publisher.
Preface

Staff Selection Commission-Junior Engineer has always been preferred by

Engineers due to job stability. SSC-Junior Engineer examination is conducted
every year. MADE EASY team has deeply analyzed the previous exam papers and
observed that a good percentage of questions are repetitive in nature, therefore
it is advisable to solve previous years papers before a candidate takes the exam.

The SSC JE exam is conducted in two stages as shown in table given below.

Papers Subject Maximum Marks Duration

Stage 1: (i) General Intelligence & Reasoning 50 Marks 2 hours

Paper-I : Objective type
(ii) General Awareness 50 Marks

(iii) General Engineering : Electrical 100 Marks

Stage 2: General Engineering : Electrical 300 Marks 2 hours

Paper-II Conventional Type

Note: In Paper-I, every question carry one mark and there is negative marking of ¼ marks for every wrong answer.
Candidates shortlisted in Stage 1 are called for Stage 2. On the basis of combined score in Stage 1 and Stage 2, final
merit list gets prepared.

In this edition, the book has been thoroughly revised. MADE EASY has taken due care to provide complete solution with
accuracy. Apart from Staff Selection Commission-Junior Engineer, this book is also useful for Public Sector Examinations
and other competitive examinations for engineering graduates.

I have true desire to serve student community by providing good source of study and quality guidance. I hope this book
will prove as an important tool to succeed in SSC-JE and other competitive exams. Any suggestion from the readers for
improvement of this book is most welcome.

With Best Wishes

B. Singh
CMD, MADE EASY
 Syllabus of Engineering Subjects
(For Conventional Type Papers)

Electrical Engineering
Basic concepts: Concepts of resistance, inductance, capacitance, and various factors affecting them. Concepts
of current, voltage, power, energy and their units.
Circuit law: Kirchhoff’s law, Simple Circuit solution using network theorems.
Magnetic Circuit: Concepts of flux, mmf, reluctance, Different kinds of magnetic materials, Magnetic calculations
for conductors of different configuration e.g. straight, circular, solenoidal, etc. Electromagnetic induction, self
and mutual induction.
AC Fundamentals: Instantaneous, peak, R.M.S. and average values of alternating waves, Representation of
sinusoidal wave form, simple series and parallel AC Circuits consisting of R, L and C, Resonance, Tank Circuit.
Poly Phase system – star and delta connection, 3-phase power, DC and sinusoidal response of R-Land R-C circuit.
Measurement and Measuring Instruments: Measurement of power (1 phase and 3-phase, both active and
re-active) and energy, 2 wattmeter method of 3-phase power measurement. Measurement of frequency and
phase angle. Ammeter and voltmeter (both moving oil and moving iron type), extension of range wattmeter,
Multimeters, Megger, Energy meter AC Bridges. Use of CRO, Signal Generator, CT, PT and their uses. Earth fault
detection.
Electrical Machines: (a) D.C. Machine – Construction, Basic Principles of D.C. motors and generators, their
characteristics, speed control and starting of D.C. Motors. Method of braking motor, Losses and efficiency of
D.C. Machines. (b) 1 phase and 3 phase transformers – Construction, Principles of operation, equivalent circuit,
voltage regulation, O.C. and S.C. Tests, Losses and efficiency. Effect of voltage, frequency and wave form on
losses. Parallel operation of 1 phase /3 phase transformers. Auto transformers. (c) 3 phase induction motors,
rotating magnetic field, principle of operation, equivalent circuit, torque-speed characteristics, starting and
speed control of 3 phase induction motors. Methods of braking, effect of voltage and frequency variation on
torque speed characteristics. Fractional Kilowatt Motors and Single Phase Induction Motors: Characteristics
and applications.
Synchronous Machines: Generation of 3-phase e.m.f. armature reaction, voltage regulation, parallel operation
of two alternators, synchronizing, control of active and reactive power. Starting and applications of synchronous
motors.
Generation, Transmission and Distribution: Different types of power stations, Load factor, diversity factor,
demand factor, cost of generation, inter-connection of power stations. Power factor improvement, various types
of tariffs, types of faults, short circuit current for symmetrical faults. Switchgears – rating of circuit breakers,
Principles of arc extinction by oil and air, H.R.C. Fuses, Protection against earth leakage/over current, etc.
Buchholtz relay, Merz-Price system of protection of generators & transformers, protection of feeders and bus
bars. Lightning arresters, various transmission and distribution system, comparison of conductor materials,
efficiency of different system. Cable – Different type of cables, cable rating and derating factor.
Estimation and Costing: Estimation of lighting scheme, electric installation of machines and relevant IE rules.
Earthing practices and IE Rules.
Utilization of Electrical Energy: Illumination, Electric heating, Electric welding, Electroplating, Electric drives
and motors.
Basic Electronics: Working of various electronic devices e.g. P N Junction diodes, Transistors (NPN and PNP
type), BJT and JFET. Simple circuits using these devices.
nnnn

(v)
 Contents
Conventional Solved Papers (Paper-II) Electrical
Engineering

Chapter 1 3. Single-Phase & Three-Phase Induction Motors

Electrical Circuits...................................... 1 and Drives................................................................................ 106

1. Basic Concepts............................................................................ 1 4. Synchronous Machines....................................................... 124

2. Circuit Laws................................................................................11

3. Magnetic Circuits.....................................................................31 Chapter 4

4. AC Fundamentals.....................................................................42 Power Systems......................................134
1. Power Generation and Economics of Generation..... 134
Chapter 2 2. Transmission Line Design and Performance............... 140

Measurements and Instrumentation....51 3. Power System Control......................................................... 143

1. Measurement of Resistance and Basics...........................51 4. Power System Studies......................................................... 147

2. Electromechanical Indicating Instruments.....................58 5. Power System Protection................................................... 150

3. Measurement of Power, Energy and Frequency...........63 6. Power Distribution and Cables........................................ 158

4. AC Bridges and Instrument Transformer.........................76 7. Estimation Costing and Utilization of

5. CRO, Electronic Measuring Instruments Electrical Energy.................................................................... 167

and Earth Fault Detection....................................................77

Chapter 5
Chapter 3 Analog Electronics................................172
1. Semiconductor Diodes....................................................... 172
Electrical Machines�������������������������������� 79
2. Transistors (BJT, UJT, JFET and MOSFET)....................... 179
1. DC Machines..............................................................................79

2. Single-Phase and Three-Phase Transformers.................91 nnnn

(vi)