0% found this document useful (0 votes)
39 views7 pages

TP FR

1. The document describes the configuration of three routers R1, R2, and R3 including IP addresses, RIP routing protocol, and Frame Relay static maps. 2. The configuration includes interface IP addresses for serial and fast ethernet ports on each router, enabling the RIP routing protocol and advertising networks. 3. The Frame Relay configuration includes encapsulation, bandwidth, and static maps associating IP addresses to DLCI values between routers R1-R2 and R2-R3.

Uploaded by

dzr di
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
39 views7 pages

TP FR

1. The document describes the configuration of three routers R1, R2, and R3 including IP addresses, RIP routing protocol, and Frame Relay static maps. 2. The configuration includes interface IP addresses for serial and fast ethernet ports on each router, enabling the RIP routing protocol and advertising networks. 3. The Frame Relay configuration includes encapsulation, bandwidth, and static maps associating IP addresses to DLCI values between routers R1-R2 and R2-R3.

Uploaded by

dzr di
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

 

1ère Ettape (Con


nfiguratio
on R1):
Router>
>en
Router#
#config t
Enter co
onfiguration
n commandss, one per lin
ne. End with
h CNTL/Z.
Router(config)#int s2/0
p address 10
Router(config‐if)#ip 0.0.0.1 255.0
0.0.0
Router(config‐if)#n
no sh
Router(config‐if)#
%LINK‐‐5‐CHANGED
D: Interface Serial2/0, cchanged statte to up
Router(config‐if)#in
nt fa0/0
Router(config‐if)#ip
p address 19
92.168.1.1 2
255.255.255
5.0
Router(config‐if)#n
no sh
Router(config‐if)#
%LINK‐‐5‐CHANGED
D: Interface FastEtherneet0/0, changed state to up
PROTO‐5‐UP
%LINEP PDOWN: Lin
ne protocol oon Interfacee FastEthern
net0/0, channged state to
o up
Router(config‐if)#eexit
Router(config)#rou
uter rip
Router(config‐routeer)#network 10.0.0.0
Router(config‐routeer)#network 192.168.1
1.0
Router(config‐routeer)#


2ème Etape (Configuration R2) :
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int se2/0
Router(config‐if)#ip address 10.0.0.2 255.0.0.0
Router(config‐if)#no sh
Router(config‐if)#
%LINK‐5‐CHANGED: Interface Serial2/0, changed state to up
Router(config‐if)#int fa0/0
Router(config‐if)#ip address 172.16.0.1 255.255.0.0
Router(config‐if)#no sh
Router(config‐if)#
%LINK‐5‐CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO‐5‐UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config‐if)#exit
Router(config)#exit
Router#
%SYS‐5‐CONFIG_I: Configured from console by console
Router#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#router rip
Router(config‐router)#network 10.0.0.0
Router(config‐router)#network 172.16.0.0
Router(config‐router)#


3ème Etape (Configuration R3):
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int se2/0
Router(config‐if)#ip address 10.0.0.3 255.0.0.0
Router(config‐if)#no sh
Router(config‐if)#
%LINK‐5‐CHANGED: Interface Serial2/0, changed state to up
Router(config‐if)#int fa0/0
Router(config‐if)#ip address 192.168.5.1 255.255.255.0
Router(config‐if)#no sh
Router(config‐if)#
%LINK‐5‐CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO‐5‐UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config‐if)#
Router#
%SYS‐5‐CONFIG_I: Configured from console by console
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#router rip
Router(config‐router)#network 10.0.0.0
Router(config‐router)#network 192.168.5.0
Router(config‐router)#







iguratio
Config on Frame
e relay :




Static m
map :




1ère éta
ape :

Router>
>en
Router#
#config t
Enter co
onfiguration
n commandss, one per lin
ne. End with
h CNTL/Z.
Router(config)#int se2/0
Router(config‐if)#eencapsulatio
on frame‐rellay
Router(config‐if)#
PROTO‐5‐UP
%LINEP PDOWN: Lin
ne protocol oon Interfacee Serial2/0, cchanged staate to up
Router(config‐if)#b
bandwidth 6
64
Router(config‐if)#frrame‐relay map ip 10.0
0.0.2 102 bro
oadcast
Router(config‐if)#n
no sh
Router(config‐if)#
PROTO‐5‐UP
%LINEP PDOWN: Lin
ne protocol oon Interfacee Serial2/0, cchanged staate to down
%LINEP
PROTO‐5‐UP
PDOWN: Lin
ne protocol oon Interfacee Serial2/0, cchanged staate to up
Router(config‐if)#
2ème étape :
Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int se2/0
Router(config‐if)#encapsulation frame‐relay
Router(config‐if)#
%LINEPROTO‐5‐UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config‐if)#bandwidth 64
Router(config‐if)#frame‐relay map ip 10.0.0.3 203 broadcast
Router(config‐if)#no sh
Router(config‐if)#
%LINEPROTO‐5‐UPDOWN: Line protocol on Interface Serial2/0, changed state to down
%LINEPROTO‐5‐UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config‐if)#
3ème étape :

Router>en
Router#config t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int se2/0
%LINK‐5‐CHANGED: Interface Serial2/0, changed state to down
%LINK‐5‐CHANGED: Interface Serial2/0, changed state to up
Router(config‐if)#encapsulation frame‐relay
Router(config‐if)#
%LINEPROTO‐5‐UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config‐if)#bandwidth 64
Router(config‐if)#frame‐relay map ip 10.0.0.1 301 broadcast
%Address already in map
Router(config‐if)#no sh
Router(config‐if)#
%LINEPROTO‐5‐UPDOWN: Line protocol on Interface Serial2/0, changed state to down
%LINEPROTO‐5‐UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config‐if)#
Router#
%SYS‐5‐CONFIG_I: Configured from console by console
Router#show frame‐relay map
Serial2/0 (up): ip 10.0.0.1 dlci 301, dynamic, broadcast, CISCO, status defined, active
Serial2/0 (up): ip 10.0.0.2 dlci 302, dynamic, broadcast, CISCO, status defined, active
Router#

You might also like