Creating A SMD Footprint in Cadence Allegro: Ricky Liu 998192101 EEC 134

Creating a SMD Footprint in
Cadence Allegro
Ricky Liu
998192101
EEC 134
Table of Contents
Abstract ....................................................................................................................................... 3
Introduction ................................................................................................................................. 3
Tutorial ........................................................................................................................................ 4
1. Getting Started .............................................................................................................. 4
2. Create Pads in Pad Designer ......................................................................................... 4
3. Arrange Pads in PCB Editor ......................................................................................... 5
4. Add Layers/Labels ........................................................................................................ 8
Tips and Tricks ......................................................................................................................... 11
Glossary .................................................................................................................................... 12
References ................................................................................................................................. 12
Appendix ................................................................................................................................... 12
Additional resources ............................................................................................................. 12
Abstract
This minimanual presents a tutorial for creating a footprint for a surface mount device
(SMD), specifically a surface mount capacitor. At relevant steps, there are explanations of the
specific features of the footprint. The software package Cadence Allegro will be used for this
tutorial.
Introduction
Printed circuit board (PCB) design is a skill that all electrical engineers obtain in their
careers. One of the most important processes of PCB design is creating footprints, an
arrangement of pads on a PCB used for attaching electronic components to the circuit board. The
process can be broken down into three simple steps, as shown in figure 1.
Fig. 1 Footprint Creation Steps

Footprints cannot be created using any arbitrary shapes and sizes. The design specifications,
including pad dimensions, are in the component’s datasheet. This tutorial uses a two pin SMD
capacitor as an example. The dimensions are listed in figure 2.
Fig. 2 SMD Capacitor Dimensions

Tutorial
1. Getting Started
The following programs must be installed onto your computer and opened before starting
this tutorial:
 Pad Designer (Cadence SPB 16.5/16.6 -> PCB Editor Utilities -> Pad Designer)
 PCB Editor (Programs -> Cadence -> Release 16.6)
2. Create Pads in Pad Designer

1. Click the Units drop-down menu and select millimeters in the ‘Units’ section of the
‘Parameters’ tab.
NOTE: The unit mils (1/1000 of an inch) is another common unit of measurement.
2. Check the box next to ‘Single Layer Mode’ in the ‘Layers’ tab.
Checking this box will limit the number of layers between the top and bottom copper
layers to one layer.
3. Select the ‘BEGIN LAYER’ row. Click the ‘Geometry’ drop-down menu and select
‘Rectangle’. Input 0.2 in the ‘Width’ box and 0.8 in the ‘height’ box.
TIP: The begin layer is the top copper layer of the PCB.
4. Right click ‘Bgn’ button and click copy. Right click ‘SOLDERMASK_TOP’ row and
click paste. Paste onto the ‘PASTEMASK_TOP’ row.
Fig. 3 Copy/Paste
TIP: The ‘SOLDERMASK_X’ and ‘PASTEMASK_X’ widths and heights can be 0.1
mm bigger than the ‘BEGIN_LAYER’.
5. Save the pad and name it GRM188R61C474KA93.
The file should be named GRM188R61C474KA93.pad. The final pad configuration
should look like Fig. 4.
Fig. 4 Pad Configuration
3. Arrange Pads in PCB Editor

1. Click File -> New.
2. Choose ‘Package Symbol’, input ‘cap0603’ in the ‘Drawing Name’ box.
3. Set the folder that the footprint will be saved.
Fig. 5
4. Click Setup -> Design Parameters. Click the ‘Design’ tab. Change the ‘User units’ to
millimeters.
5. Click the ‘Display’ tab and click to set up the grids.
6. Change all ‘x’ and ‘y’ boxes to 0.0254.

Changing the ‘x’ and ‘y’ values makes each dot on the grid 0.0254 mm (1 mil) apart.
7. Click ‘OK’ to close the ‘Define Grid’ window. Close the ‘Design Parameter Editor’.
8. Click Layout -> Pins. Click ‘Options’ on the right side of the window, as shown in Fig. 6.
Fig. 6.
9. Choose GRM188R61C474KA93 for ‘padstack’, input 1.6 in the ‘Spacing’ box in the ‘x’
row, and 0.5 in the ‘Spacing’ box in the ‘y’ row, as shown in fig. 7.
Fig. 7
10. Click anywhere on the workspace (black grid) to place the pads.
NOTE: The black grid is the area of the PCB Editor program where the footprint is
placed.
11. Save the file as GRM188R61C474KA93.dra.
WARNING: Several windows will pop up warning you that the footprint is missing
features. Close the windows and continue to the next section.
4. Add Layers/Labels
1. Click Shape -> Rectangular. Click Options on the right side of the window.
2. Choose ‘Package Geometry’ from the top drop-down menu and choose
‘Place_Bound_Top’ in the bottom drop-down menu, as shown in fig. 8.
Fig. 8
3. Place the rectangle onto the workspace so that the rectangle is surrounding the pads, as
shown in fig. 9.
Fig. 9
4. Click Add ->Line. Click Options on the right side of the window.
5. Choose ‘Package Geometry’ from the top drop-down menu and choose ‘Silkscreen_Top’
from the bottom drop-down menu.
6. Set Line lock: line , 90
7. Set Line width: 0.05
8. Draw the lines around the pads, leaving 0.05 mm between the pad edge and the line, as
shown in fig. 10.
Fig. 10
9. Repeat steps 1 and 2, except choose ‘Assembly Top’ from the bottom drop-down menu.
10. In ‘Shape Creation’, Select ‘Place Rectangle’ and set the width and height to be 1.8 mm
and 1 mm, respectively.
Fig. 11
11. Place the rectangle in the workspace as shown in fig. 12.
NOTE: The center of the rectangle should be aligned with the origin.
Fig. 12
12. Click Layout -> Labels -> RefDes
Fig. 13
13. In Options, select ‘Assembly Top’ from the drop-down menu.
14. Click anywhere in the workspace and type ‘C*’.

15. Repeat steps 12-14 for ‘Silkscreen Top’. The symbol should look like fig. 14.
Fig. 14
16. Save the file.
NOTE: The footprint is finished when the following layers are present:
 Bound_Top
 Silkscreen_Top
 Assembly_Top
 RefDes Silkscreen
 RefDes Assembly Top
Tips and Tricks

 Practice undoing actions by right-clicking and pressing ‘oops’.
 The black grid workspace can be moved by pressing and holding the middle button
on the mouse and moving the mouse.
 Use the visibility tab on the right side of the screen to show and hide desired layers.
 The options tab can be pinned to the workspace by clicking the thumbnail button.
Glossary
Assembly Layer: layer that contains the information about the placement and orientation of all
the components on the circuit board.
Bound Layer: layer that contains the outline of the footprint.
Footprint: graphical symbol composed of pads used for connecting electronic devices to a
circuit board.
Pad: also known as pins; surface of the circuit board designated for soldering electronic
components.
Pastemask Layer: layer that contains information about the places on the circuit board where
there should be no pastemask.
Pins: leads on an electronic device for connecting to other circuit components; pin is also used
interchangeably with pad when referring to the footprints.
Reference Designator (RefDes): A standardized method of identifying a device on a printed
circuit board. Typical reference designators begin with a letter, followed by a number.
Silkscreen Layer: layer that contains the labels and outlines of every component.
Soldermask Layer: layer that contains the information about the places on the circuit board
where there should be no soldermask.
References
“Capacitor Data Sheet”. GRM188R61C474KA93. Murata. April, 2016
“Complete PCB Design Using OrCAD Capture and PCB Editor”. Mitzner, Kraig. Elsevier,
2009. Print.
“GRM Series” Murata April 30, 2016. <http://www.murata.com/en-us/products/capacitor/mlcc>
Appendix
Additional resources
http://www.referencedesigner.com/tutorials/allegro/allegro_page_1.php
http://www.referencedesigner.com/tutorials/allegro/allegro_page_5.php

Creating A SMD Footprint in Cadence Allegro: Ricky Liu 998192101 EEC 134

Uploaded by

Copyright:

Available Formats

Creating A SMD Footprint in Cadence Allegro: Ricky Liu 998192101 EEC 134

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Creating A SMD Footprint in Cadence Allegro: Ricky Liu 998192101 EEC 134

Uploaded by

Copyright:

Available Formats

Creating a SMD Footprint in

Fig. 1 Footprint Creation Steps

Fig. 2 SMD Capacitor Dimensions

2. Create Pads in Pad Designer

Fig. 4 Pad Configuration

3. Arrange Pads in PCB Editor

6. Change all ‘x’ and ‘y’ boxes to 0.0254.

11. Save the file as GRM188R61C474KA93.dra.

6. Set Line lock: line , 90

7. Set Line width: 0.05

12. Click Layout -> Labels -> RefDes

13. In Options, select ‘Assembly Top’ from the drop-down menu.

14. Click anywhere in the workspace and type ‘C*’.

Tips and Tricks

You might also like