Air Handling Units - Equipment Guide

FORM 102.
20-QG1 (808)
V
F
D V
FPC F
D
EA
DP HF XA FS XA CC XA HC RF MB FE
SA
RA
Split
ld08301
FS DI RF XA DP
Split
VFD EA
VC XA HC RF MB FE
RA
Split
ld08302
SOLUTION AIR HANDLING UNITS

2000 TO 100,000 CFM
(Indoor & Outdoor Models)
FORM 102.20-QG1 (808)
TABLE OF CONTENTS
GENERAL INFORMATION STAGGERED COIL OPTIONS

Introduction ............................................................3 Angle Wall ............................................................32
A Proud History of Experience & Qualifications .....3 Back-to-Back ........................................................32
Assurance of Johnson Controls Backing ...............3 Multizone (MC) .....................................................33
Computer Selection Programs ...............................4 HEATING SEGMENTS
Innovative Engineering & Design ...........................5 Integral Face & Bypass ........................................34
Flexibility of Design ................................................6 Indirect Gas-Fired ................................................35
Superior Casing Performance ................................6 Turndown Examples and Guidelines....................36
Pre-engineered Packaged Controls .......................7 Electric Heat Options & Applications ....................37
Customized Variable Size Openings ......................7 ENERGY RECOVERY
Airflow Measurement Performance ........................8 Heat Wheel ..........................................................40
State-of-the-Art Certification & Testing ...................8
FILTER SEGMENTS
New Sound Testing Laboratory ..............................8
Applications & Options Table ...............................41
Quality Construction Equals Improved IAQ............9
Mechanical Air Filters ...........................................42
Multi-Sloped Drain Pans ........................................9
MERV Analysis .....................................................43
Raceways...............................................................9
MIXING SEGMENTS & ECONOMIZERS
Improve Cost Savings ............................................9
Mixing Box /Economizers .....................................44
A Complete Line of Filters ....................................10
Mixing Box Optimization Chart .............................46
Energy Saving Fan Options .................................10
Typical Economizer Application............................47
Energy Consumption............................................11
Building Pressurization.........................................47
Sound Attenuation ................................................13
Methods of Pressurization Control .......................48
Inertia Base ..........................................................13
Economizer Arrangements ...................................48
Quick Selection ....................................................14
Face Damper .......................................................49
FAN APPLICATION REVIEW
Inlet Plenum .........................................................49
Fan Laws .............................................................15
ACCESSORY SEGMENTS
Variable Air Volume ..............................................16
Diffuser Segment .................................................50
Component Temperature Margins ........................17
Access Segment ..................................................50
Fan Motor Heat ....................................................17
Vertical Plenum ...................................................51
COIL OPTIONS
Discharge Plenum ................................................51
Cooling Coils ........................................................18
Sound Attenuator .................................................52
Heating Coils ........................................................19
Noise and Vibration ..............................................53
Typical Application of AH Coils .............................20
Air Blender - Mixers..............................................54
SOLUTION SEGMENT IDENTIFICATION Face & Bypass Damper Segment ........................55
Segment Listing ...................................................21 Turning Segments ................................................56
Unit & Coil Hand Selection ...................................21 Humidifier Segment..............................................56
FAN SEGMENTS – FS, FR, FE UV Segment .........................................................57
Fan Applications ...................................................22 Pipe Chase Enclosure..........................................58
Dual Fan Considerations......................................22 Roof Curb .............................................................58
Dual Fan Applications ..........................................22 Special Curb Requests ........................................59
Door and Discharge Locations .............................23 CONTROLS
Single Fan DWDI Options ....................................24 F. P. Controls & Motor Control Centers ................60
Single Fan SWSI Options ....................................25 Typical FPC Wiring...............................................60
Dual Fan DWDI Options.......................................26 Software Process .................................................61
Dual Fan SWSI Options .......................................27 Field Equipment Controller...................................61
SWSI vs. DWDI ....................................................28 Power Wiring Options ..........................................62
Fan Motor Control Methods .................................29
INDUSTRY FORMULAS
COIL SEGMENTS Miscellaneous Industry Formulas.........................63
Cooling (CC) ........................................................30
GUIDE SPECIFICATIONS WITH TIPS
Heating (HC) ........................................................30
Part 1 - General....................................................64
Vertical Coil (VC) ..................................................31
Part 2 - Products ..................................................67
Part 3 - Execution.................................................81
2 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
GENERAL INFORMATION
Introduction Assurance of Johnson Controls Backing

This Equipment Guide will provide engineers with With every Solution system, you get the support and
a summary of Solution air handling information in the resources that come from dealing with a worldwide
most convenient, time-saving manner possible. The manufacturer – JOHNSON CONTROLS. You are not
guide will direct you to various sources of data and infor- tied to the limitations of a regional supplier. Instead, you
mation helpful in solving questions concerning product get the flexibility being able to design in one part of the
options, design application, as well as installation and country, and buy and install in another location.
operation.
Johnson Controls Factory Service
A Proud History of Experience & Qualifications
Turn to the experts at Johnson Controls/YORK.
Johnson Controls combined with YORK heating, ventila- Johnson Controls/York carries the burden of single-
tion, air-conditioning, and refrigeration (HVAC&R) sys- source responsibility since Johnson Controls/YORK
tems and solutions creates the largest global provider of packages the total system, including custom air han-
integrated products, systems and services for the $200 dlers, chillers, controls, and variable air-volume boxes
billion global building environment industry. and building automation systems. For added peace
of mind, Johnson Controls/YORK offers Inspection
Johnson Controls/YORK is: Only, Preventive Maintenance and Inspection, or Total
• A global leader in control systems and services Service Contracts to meet your specific financing and
for heating, ventilating, air conditioning (HVAC), management requirements. Johnson Controls service
lighting, security and fire management for non- can also provide certified technicians available locally
residential buildings, facility management and for factory start-up, drawing from over 700 factory-
consulting services. trained service technicians in 100 strategically-located
offices nationwide – a capability not offered by indepen-
• Represented in over 125 countries, including
dent manufacturers.
North America, Asia, Europe, the Middle East,
Africa and Latin America and in all markets.
® Full Service Support
YORK Solution® air-handling units (AHUs) from John-
son Controls–the only names you need to know for a line Because JOHNSON CONTROLS factory packaged
that has no limits. Johnson Controls/YORK engineers devices and motor controls are an integral part of the
have developed an AHU line that is so flexible, and able equipment, who better to troubleshoot and service the
to deliver such high standards of performance, that it can system than a professional Johnson Controls Service
handle virtually any application. Whatever the air-han- Technician. The Johnson Controls Service technician
dling challenge–IAQ, acoustics, energy, controls, you knows not only the equipment and the hardware, but
name it–Johnson Controls/YORK can build a Solution also has a working knowledge of equipment applica-
AHU that will meet your needs. tion and operation. Every unit is backed by this kind of
professional support.
Solution® AHU’s from Johnson Controls
comprise a complete AHU line to meet commercial,
institutional and industrial indoor and outdoor unit Development and Preparation of Service Literature
applications. For more than 50 years, YORK air
Johnson Controls/YORK produces quality product
handling units have been installed in every type of facility to
literature to ensure proper installation, operation and
handle any type of requirement; manufacturing, education,
maintenance. Installation, Operation and Maintenance
healthcare, life sciences and process manufacturing.
manuals must be followed to realize the full capacity
Solution® AHU’s come equipped with industry-leading and life of the units. In addition, literature supplements
Metasys® controls that are installed and commissioned of special characteristics and features are distributed as
at the factory. Factory installation assures superior required to support regular product enhancements.
quality, saves time on the jobsite and delivers accurate
performance. Plus, you can count on seamless opera-
tion with a Metasys building management system.
JOHNSON CONTROLS 3
FORM 102.20-QG1 (808)
GENERAL INFORMATION
Computer Selection Programs This powerful software tool brings flexibility and com-
puting power to the desktop of designers. The software
YORKworks™ software is the primary source for the
allows you and the customer to make product decisions
latest product design and performance data.
and view performance data in a user-friendly, step-by-
1. Includes the latest innovations, updates, and ef- step, screen-driven environment.
ficiencies of YORK® products
YORKworksCE™ software is a necessity for your
2. Includes general functionality used to select customer’s engineering toolbox. YORKworks revolution-
equipment factory packaged controls. izes the way you specify HVAC equipment. Johnson
Controls/YORK can optimize the selection of any air
3. Sound data for air-handling units
handling unit for a specific job requirement with its
4. All screens are interconnected and are continually computer selection programs.
updated according to configuration inputs.
Quick and Easy selection
• Save Time – choose components and

complete configurations with a couple
of clicks.
• Reduce Errors – use pre-programmed
rules and guidelines for component
selection.
Just Click to
select and add
components
Literature Reference — see ‘Sales Guide – YORK works CE’ Form 70.02-SG1
4 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Innovative Engineering & Design 5. Solution’s Variable Aspect Ratio eliminates the
need for costly modifications.
Solution Air Handlers are not just ‘fans-in-a-box’!
6. Solution fits the specification and the space!
1. Solution is a structure that withstands deflection
2. Solution is a sound/noise barrier Innovative Engineering & Design allows you to choose
from a limitless variety of configurations. See con-
3. Solution is a container of clean and conditioned air
figurations below for some of the popular applications
4. Solution is an integral part of a building’s fire and designed to meet your particular need.
safety plans
Configuration 1 (Stacked Unit) – Configuration 2 (Stacked Unit) –

Mechanical room favorite. Reduced footprint with tiered Ultra-quiet design with plenum fan and U-shaped
supply fan cabinet
AT DP
FS
TN
TN
VC XA HC FM
FS XA EH XA RF MB
Configuration 3 – Minimum frills. Maximum IAQ
FS CC XA HC FF MB
Configuration 4 – Exhaust air flexibility with gas-heat and humidification
DP HM XA IG XA FS CC AF EE FE
Configuration 5 – Cooling-only lab design with HEPA filtration
DP HF XA DI FS CC RF MB
Configuration 6 – Classic hospital design with return fan economizer operation.
DP RF XA DI FS CC XA HC AF EE FR
JOHNSON CONTROLS 5
FORM 102.20-QG1 (808)
GENERAL INFORMATION
Flexibility of Design Component Flexibility

Solution AHUs offer the ultimate in dimensional, mate- AHUs are responsible for providing
rial, and component flexibility. Solution AHUs have the the environment with quality indoor
same appeal for both “standard” and “custom” markets. air, in an energy efficient and quiet
How an air-handling unit is designed and built deter- manner. Solution AHUs help meet
mines how well it performs. that responsibility by offering every
available component, from energy
Engineering Flexibility wheels to air-monitoring stations
to specialty-purpose filters. As
• Variable cabinet dimensions
technology creates new capabilities, Johnson Controls/
• Material and component flexibility YORK will apply these to our Solution line.
• Full line of factory packaged controls installed, Superior Casing Performance
tested and commissioned by Johnson Controls
The foam injected panels of our Solution air handling
certified technicians
units enhance performance, maximizing the indoor air
• Variable sized inlet and discharge openings quality and help to create ASHRAE 62-2000 compliant
designs while reducing costs. The direct result of the
• Indoor and outdoor constructions
foam injection insulation is a rigid panel, low leakage,
• Tiered (stacked) and custom configurations high pressure air handler, with increased energy sav-
ings, and reduced initial cost.
Better IAQ
Deflection presents a potential in leaks that form over
time from the operational pressure. The foam injected
Solution panels are 20% more rigid (L/240 vs. L/200)
then the typical fiberglass or foam board construction.
In addition the smaller deflections can be achieved using
lighter sheet metal gauges then required by fiberglass
construction. The result is a lower initial cost unit with
greater performance.
Lower leakage reduces the infiltration of unfiltered and
unconditioned air into the space. The infiltration of un-
• Panels are individually removable without affect- conditioned air can lead to condensation in unit walls,
ing structural integrity. crevices and/or insulation. When the infiltration occurs
in a negative pressure atmosphere downstream of the
Dimensional Flexibility filter, it will lead to unfiltered air being supplied to the
space. Maintaining a low leakage for positive pressure
You can design Solution AHUs to fit the application and
segments reduces the loss of conditioned air to a po-
the space. Length, height and width can all be varied
tentially warm and humid ambient environment, causing
to match building constraints. With hundreds of cross-
increased condensation. Condensation can lead to
sectional possibilities, you choose the best match for the
premature corrosion as well as IAQ concerns.
application. In addition, all Solution AHU components
have been designed with a variable-aspect ratio to meet The Solution foam injected wall panels help to seal and
your space and air-velocity requirements. maintain the leakage at maximum of 1% with a minimum
+/-8” of static pressure. Options for a maximum leakage
Material Flexibility rate of 1/2% at a minimum of +/-10” of static pressure
are available for those projects which demand it.
A complete line of construction materials are available,
including galvanized steel, aluminum, painted steel, Coil carryover, humidification, and periodic wash downs
stainless steel, and more. Solution AHUs can handle are all instances where water is present in the unit.
a multitude of environments, from the most benign to Foam insulated panels will not absorb, and retain water,
the most corrosive. NOTE: All units/unit segments are like a fiberglass insulated panel will. In addition the ther-
shrink-wrapped to protect unit from contamination dur- mal properties of foam are not degraded by an incident
ing shipping where the insulation comes in contact with water.
6 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Energy Savings Factory Installation

The energy savings associated with high performing air Factory installation improves quality and saves time.
handler construction is directly associated with leakage While a Solution AHU is being manufactured, Johnson
and insulating properties. Controls technicians can easily access all its segments.
So there are no accessibility problems to cramp the
The infiltration of unconditioned air downstream of a coil,
quality of the controls installation, which often occurs
or the loss of conditioned air downstream of a coil are
on the jobsite.
just two examples of reduced energy efficiency in an air
handler. The foam injected panel helps to reduce both All sensor probes have been pre-engineered to deter-
of these potential losses by creating a more rigid, lower mine the best mounting location, ensuring accurate and
leakage air handling over the life of the unit. reliable readings.
Another form of energy loss associated with air handlers This improves performance of the unit while eliminat-
is the thermal energy that is lost through the cabinet of ing unwanted air leakage common in field-mounted
the air handler. The Solution foam injected panels lower solutions.
energy consumption with better insulating properties.
With the standard R-12.5 and optional R-18.8, or R-25, Factory engineering speeds field connections
the Solution can help to reduce the energy usage. The
The goal is to provide
injected panel provides additional thermal advantages in
you with an AHU that
that the foam will fill voids, and gaps that aren’t reached
simplifies field connec-
with fiberglass or foam board type constructions.
tion of the controls. For
Solution air handler units are capable of being factory example, coil valves
tested to prove out both leakage and deflection. With are shipped uninstalled,
the Solution product it’s not all about construction, it’s but pre-wired with quick
also about performance. connects. If an AHU is
too large to ship in one
Pre-engineering Packaged Controls
piece, you can still count
Pre-engineering of sensors ensures the most accurate on fast and easy assem-
performance. There are great advantages to selecting bly of Metasys controls
factory mounted and wired end devices for your Solution because labeled quick connects come standard on all
air handling units. shipping splits.
1. Factory mounting maintains leakage performance
Customized variable size openings
2. Factory wiring is plug and play
Solution offers the most comprehensive option for facto-
3. Factory testing of each mounted and wired device ry provided openings. Custom size, custom location and
custom shapes along with custom sized dampers,are
4. Factory generated control diagrams specifically
designed to lower installation costs and risk while dra-
for each unit
matically improving the quality of the application and
performance of the air handler.
DP FS EE EE FR IP
Literature Reference — see Application Guide ‘Applying VSO Option to Solution Air Handling Units’ - Form
102.20-AG14
JOHNSON CONTROLS 7
FORM 102.20-QG1 (808)
GENERAL INFORMATION
Airflow Measurement Performance air-flow station offered for air handling units which is in-
corporated into mixing box and economizer segments to
Solution AMS-60 qualifies to bear the AMCA Ratings
meet the most stringent ASHRAE 90.1 requirements
Seal for Airflow Measurement Performance. Ventilation
air flow can be controlled dynamically with the Solution There are 3 damper options to give various measure-
AMS-60 which is tested to AMCA Standard 611-95. ments of air flow. See FIG. 1.
The Solution AMS-60 continues to be the best integral
NOTE: Dampers are split vertically
VIEWED
FROM 25% 25%
TOP
100%
75% 75%
FIG. 1 – DAMPER OPTIONS
Literature Reference — see Application Guide ‘AMS60 for use with Solution AHU’ - Form 102.20-AG1
State-of-the-Art Certification & Testing

• ASHRAE 90.1 compliant
Solution Air Handlers are subject to stringent testing
using certified, comprehensive and industry recognized • ASHRAE 62 compliant coil and drain pan design
testing laboratories. Testing is in accordance with ARI maximizes indoor air quality
Standard 430 which evaluates the performance of the
• Outstanding thermal capacity proven through
entire unit. This assures that each Certified Solution unit
independent testing
will indeed perform with certainty and reliability.
• HEPA filtration system exceeds the most stringent
Solution AHUs have also undergone extensive and rigor-
military DOP tests
ous testing to verify conformance with all U.S. and Cana-
dian safety standards, and they bear the ETL Label. • AMCA 611 certified airflow measurement stations
Extensive testing includes: • ISO Quality Certification
• ARI 430 certified performance • Seismic certificate of compliance
• ARI 260 sound data Labeled Solution units are tested and listed by ETL in
accordance with UL 1995, Standard for Safety Heating
• Full line of ARI 410 certified coils
and Cooling Equipment, and thereby fully complying
• ETL listing for product safety per UL 1995 with NFPA 90A material requirements.
New Sound Testing Laboratory our customers will continue to obtain the best available
Solution sound data in the marketplace.
The new AHU laboratory at the Johnson Controls
Grantley Park Tech Center includes the capability for This facility will be the largest AHU sound test facility in
sound power measurements on Air Handling Units up to the world. Note that in order for a laboratory to measure
100,000 CFM in accordance with ARI 260. The facility ARI 260 sound data, the laboratory must be pure tone
will also include the capability for testing unit airflow in qualified to 50 Hz. This facility will be pure tone quali-
accordance with AMCA 210 to 100,000 CFM. For fan fied to 50 Hz. Pure tone qualification ensures that the
alone testing, the facility will also have AMCA 300 and test facility is capable of accurately measuring a noise
AMCA 210 accreditation. All of this capability will be source producing tones – such as a fan. Not qualifying
available for product development testing and for cus- the facility for pure tone response could lead to errone-
tomer witness testing on critical projects. This facility ous results with a tonal noise source. This is why ARI
will allow verification and calibration of sound models requires pure tone qualification of reverberation rooms in
used for unique features of Solution units, which will the HVAC industry for anything other than VAV boxes.
increase the accuracy of our predictions and ensure that
8 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Quality Construction Equals Improved IAQ states that “The drain pan outlet shall be located at the
lowest point(s) of the pan.”
Quality construc-
tion is a key to a Solution units remove the condensate with a multi-sloped
minimum amount of drain pan that ensures positive drainage. Our pan design
AHU leakage. Leak- also offers the highest level of accessibility for periodic
age is an adversary cleaning, now required by ASHRAE Standard 62.
of indoor air quality.
It will depreciate the Raceways
quality of the supply
Raceways are used as the exterior skeletal construction
air by allowing dirty,
of Solution.
unfiltered air to seep
into the air-stream • Raceways provide the form and shape as well as
downstream of the structural support for panels, base and internal.
filters.
• Raceway material is Galvanized
To prevent this leakage, the rigid, thermally superior
Solution is offered with a full-perimeter base-rail with
panels of Solution AHUs are matched with a rugged
integral lifting lugs.
framework to provide an extraordinary casing perfor-
mance. • Optional base-rails
The maximum allowable air leakage is less than 1% at • Lifting lugs are provided
+/- 8" w.g. and a maximum L/240 deflection. as necessary for material
handling
The Shell of Solution is made up of double wall panels
and doors. A ‘Curb Rest’ is provided to
direct, guide and indicates align-
• Standard liner material is galvanized
ment when setting a unit on the
• Stainless liners are optional curb.
• Perforated aluminum liners are optional • Galvanized steel strip at-
tached to the raceway or
The floor is a double wall construction, with a galvanized
base-rail
steel walk-on surface.
• ‘Curb Rest’ is not to be
• Optional stainless steel
considered a flashing
• Optional aluminum tread plate receiver for the curb.
Multi-Sloped Drain Pans Improve Cost Savings

The way to control micro-organisms, which can flourish Solution UV-C light options
in drain pans, is to control the moisture of cooling-coil eliminate the potential for a build-up of microbiological
condensate which can remain in the pan during “off” or agents.
“heating” cycles.
1. Heat exchangers continue to operate at high-
Poorly designed drain pans efficiency levels due to sustainable, like-new,
are often breeding grounds reduced pressure drop.
for mold and poor IAQ.
2. HVAC equipment operates for shorter periods of
ASHRAE 62-2001, section
time saving cost on electricity.
5.11.1 states that drain pans
“...shall be sloped at least 3. Improved IAQ as the first line of defense against
1/8" per foot from the hori- sick building syndrome.
zontal toward the drain outlet
Installation of UV-C lamps promotes a cleaner, healther,
whether the fan is in the on or
more productive work environment.
off position.” Section 5.11.2
More detailed information on page 57 of this manual.
Literature Reference — see Application Guide ‘Solution IAQ Series General AHU Construction’ - Form 102.20-
AG3
JOHNSON CONTROLS 9
FORM 102.20-QG1 (808)
GENERAL INFORMATION
A Complete Line of Filters

A complete line of clean air solutions for industrial plants,
hospitals, schools, pharmaceutical process, airports and
commercial buildings are available to control or remove
airborne contaminants from the air stream.
Achieving acceptable indoor air quality is more involved
than calculating and applying the appropriate ventilation
rate. Specific AHU performance and other common
sense specification items, tied to ASHRAE 62.1 rec-
ommendations, can help achieve the healthy indoor air
quality environment desired.
Light pre-filtering duty: Stringent filtration requirements: Odor or VOC removal

– pleated – HEPA – Activated carbon
– extended surface – Ultra-HEPA
– 17 to 18 MERV Air purification systems
Higher filtration efficient – 0.3 & 0.1 microns respectively High-performance
– 60% to 95% – 99.97% & 99.99 % effectiveness – Near-HEPA performance
– 11 to 14 MERV – Germicidal capability
– rigid & bags – Low-resistance-to-airflow (initial
pressure drop equal to a low-end
pre-filter).
Energy-Saving Fan Options Economizers (EE) provide an exhaust path for return
air, allowing the outdoor air conditions, when suitable,
In any AHU, the fan is the largest energy consumer.
to take advantage of 100% outside air for “free” cooling,
Solution fans offer a range allowing the chillers to be turned off a percentage of the
of energy-saving options time during the cooling season. Return and exhaust
through fan types and con- fans are available to meet the needs of varying building
trols. pressurization requirements.
– Light aluminum fan
wheels
– Direct-drive plenum
fans, which eliminate
belt-and-pulley energy
losses
To assure the quietest
possible operation,
fans and motors are
common base isolated
from the cabinet.
Literature Reference — see Application Guide ‘Solution - Reducing AHU Energy Consumption’ - Form 102.20-
AG13
10 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Energy Consumption Rearranging Equation 1 to solve for duct leakage class:

The HVAC industry has taken a leadership role by creat- Eq. 2 CL = Lmax/P0.65
ing energy-performance guidelines, such as ASHRAE CL = (0.5 cfm/ft2 x 100 ft2)/50.65
90.1. Solution AHUs are designed with ASHRAE 90.1 CL = 17.6
in mind.
In extreme ambient conditions, heat transfer through According to this, regardless of unit size or capacity,
the casing must be controlled. Solution casing offers this type air-unit is roughly equivalent to a SMACNA
maximum thermal performance in the floors, walls and leakage class of 18.
roof. To prevent energy-robbing air leaks, Solution units
are designed for a maximum casing leakage of less Analyzing Solution units is a little more complex than
than 1%. analyzing the other typical unit, since Solution strives
for a maximum leakage rate of 1% of the unit design
airflow at ± 8 in-w.c. That means that the leakage in
cfm/100 ft2 of unit casing varies based on the size and
capacity of the unit. A 4,000 cfm Solution unit will have
a maximum leakage rate of 40 cfm, whether the unit is
8’ long or 10’ long. Therefore, the 10’ long unit will have
an inherently lower cfm/100 ft2 leakage rate than the 8’
long unit, as shown in Table 1.
For every 1% of air leakage at the AHU, 1% more air Table 1. Comparative Solution Leakage Rates
must be conditioned, and 1% more energy is con- Unit CFM: 4000 4000 16000 16000 32000 32000
sumed. H (Inches) 36 36 66 66 114 114
W (inches) 54 54 96 96 102 102
Comparing Apples-to-Apples L (inches) 98 124 105 132 125 150
Competitors claim “Air leakage rates between 1/2 and Area (ft2) 150 182 324 385 537 612
1 percent” on their AHUs, but they don’t mention at what 1% Leakage (cfm) 40 40 160 160 320 320
pressure this performance is achievable, nor do they Leakage (cfm/ft²) 0.27 0.22 0.49 0.42 0.60 0.52
even specify a leakage rate for the air units.
Using the Solution performance at ± 8 in-w.c. we can use
This typically makes it difficult to analyze their leakage the SMACNA leakage class as a standard comparator.
performance by not qualifying it based on air pressure. By plugging the values from Table 1 into Equation 2, we
However, if we reference to SMACNA class 3 air leakage find the leakage class for the various Solution units as
this is a good place to begin our analyses. shown in Table 2.
SMACNA class 3 refers to a standardized method Table 2. Solution AHU Leakage Classes
of classifying duct leakage. While this classification
Unit CFM: 4000 4000 16000 16000 32000 32000
doesn’t technically apply to AHUs, it is a useful method
of comparing the performance claims of different manu- Leakage (cfm/ft²) 0.27 0.22 0.49 0.42 0.60 0.52
facturers. According to SMACNA Duct Leakage Test Leakage Class
7 6 13 11 15 14
Procedures (1985), duct leakage is calculated using at ± 8 in-w.c
the equation:
Eq. 1 Lmax = CLP0.65 Even on large AHUs, the leakage class of a Solution
unit is lower than that of most competition. Many design
where, engineers don’t realize this, because when they compare
YORK’s performance to others they aren’t comparing
Lmax = maximum permitted leakage in cfm/100ft2 duct surface area;
apples-to-apples unless the performance is translated
CL = duct leakage class, cfm/100ft2 at 1 in-w.c. into the common language of leakage class.
P0.65 = test pressure in in-w.c.
Literature Reference — see Application Guide Form 102.20-MG1. See also M-42-06.
JOHNSON CONTROLS 11
FORM 102.20-QG1 (808)
GENERAL INFORMATION
EPAct Efficient Performance

Consumption of energy can also be reduced by more
efficient motors. Solution AHU motors meet EPAct
efficient performance standards for general purpose
motors. Standard Solution EPAct efficient and Premium-
efficiency motors can be specified and used with fre-
quency control as listed by NEMA Standards Publication
MG 1-2006 (Motors and Generators):
• MG 1-2006 Part 30
Application Considerations for General Purpose
Motors used with Adjustable - Voltage OR Adjust-
able - Frequency Controls or Both
• MG 1-2006 Part 31
Definite-Purpose Inverter-Fed Poly-phase Motors
Literature Reference — see Application Guide ‘Solution Air Handling Units AC Induction Motor Data’ -
Form 102.20-AG15.
Energy Saving Air-Modulator™ 3. Eliminates need for motor

When the air system is de- starter panels.
signed for variable-air vol- 4. Improved system control
ume (VAV), Solution offers and response – DDC
the most efficient method of controls with LED digital
VAV fan control with our Air- display.
Modulator™ drive, which is
mounted, wired and tested in 5. Proven reliability.
our factory.
Fans characteristically require Typically HVAC systems consume
much less power as the speed a third of the energy used in com-
is reduced. With the Air-Modulator™, any reduction in mercial buildings. Therefore an
fan speed results in a cubic reduction in fan horsepower. energy-efficient HVAC system can
For example, a 10% speed reduction results in a 27% represent a significant savings in
fan horsepower reduction! building operating costs. ASHRAE
Air Modulator benefits include: 90.1 provides architects and engi-
neers with guidelines for the design
1. Extended Equipment Life – soft start of motor and of energy efficient buildings, with
fan. the exception of low-rise residential
2. Quieter Fan Operation – buildings.
fan operating at reduced speed and constant line
of efficiency.
Literature Reference — See Application Guides ‘ASHRAE 90.1 Guidelines’ – Form 102.20-AG2 & ‘Understand-
ing AHU Casing Leakage’ – Form M-42-06
12 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Sound Attenuation What little noise is left can be further reduced with direct
methods of sound
An important component of indoor environmental qual-
attenuation. Using
ity (IEQ) is acoustics. There are very few constants
perforated sound-
when it comes to acoustics, however it is always less
absorbing walls as
expensive to design and install a system correctly the
sound traps in the
first time than it is to make the system quiet after it is
fan and discharge-
installed. The best way to reduce noise is not to create
plenum sections,
it in the first place.
Johnson Controls/
ARI 260 requires that the unit be rated across its entire YORK equipment
operating range according to the AMCA 300 test method. engineers can help
Johnson Controls/YORK has been and continues to be you design units
fully engaged in a rigorous ARI 260 testing program. to meet your criti-
Solution testing includes a wide variety of fan types, cal sound require-
unit sizes and configurations. As a result, Solution can ments.
with assurance say sound power levels are reported in
accordance with ARI 260.
Inertia Base
Solution AHU offers a variety of noise-reducing tech-
A concrete inertia base, which is inserted between the
nologies.
fan and its supportive structure, can be quickly and eco-
Solution AHUs are available nomically installed in all Solution unit cabinet sizes.
with a nearly endless array
– Inertia fan bases will accommodate both belt
of fan types, all custom
driven and direct drive fans
selected for the exacting
requirements of your project. – The added mass of the inertia base allows for a
Direct drive plenum fans softer isolation system and greater isolation ef-
can reduce vibration and ficiencies as well as an effective means of damp-
drive noise by eliminating ening mechanical noise.
the belt-and-pulley mecha-
– Concrete fill is furnished by contractor.
nism. A range of fan-base
construction and isolation techniques are available to
help control sound.
SOUND
ATTENUATION
Source attenuation
is the first sound-re-
duction method that
should be consid-
ered, and is typical-
ly least expensive.
Since the fan is the
primary moving part
in an air-handling
system, it’s the first
RACEWAY ASY
place to look when
reducing noise.
Application Note - As a rule of thumb the inertia base
BULKHEAD ASY
should be used when:
• Class II & III fans with 40” diameter wheel or larger
• All centrifugal fans driven by motors of 75HP or
larger
JOHNSON CONTROLS 13
FORM 102.20-QG1 (808)
GENERAL INFORMATION
Quick Selection
The Quick Selection Guide for the Solution AHU was developed and intended to aid the Consulting Engineer, Ar-
chitect, Design/Build Contractor, and Equipment /Controls Engineer in establishing overall estimates for (minimally)
footprint dimensions, unit weight, & max motor horsepower.
Contents consist of:
– Applications, Features & Benefits
– Instructions
– Data
– Notes
– Reference Formulas and Conversions
Literature Reference — See Quick Select Tool – Solution Slide Chart – Form 102.20-SC1
14 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Fan Laws (Recommended Accepted Practice) System curves will always have a square function slope
(parabola) because the SP varies as a square of the
The fan laws are used to calculate performance char-
CFM. The point where the system curve intersects the
acteristics; fan speed (RPM), fan air capacity (CFM),
RPM curve is the operating point of the fan (point A).
static pressure (SP) and brake horsepower (BHP) of
If the system resistance changes (i.e., dirty filters or
a particular fan at conditions other than those at which
change in ductwork), the operating point will move along
the data was taken.
the RPM curve to a different operating point and there-
By using the fan laws in conjunction with a fan curve, the fore, new system curve (point B). With a fixed system,
fan performance can be calculated accurately at various the effects of change in RPM, air density of BHP can
operating conditions. Every fan has its own unique fan be calculated and plotted on the system curve by using
curve. FIG. 2 shows a fan curve at various RPMs. the following fan laws:
The system resistance curve relates the total pres- • The CFM varies directly with the RPM:
sure loss in an air handling system to the flow rate of
RPM2
air through the system. The system curve is unique to CFM2 = CFM1 x
each system because it expresses the pressure losses RPM1
associated with the system. (AHU cabinet, coils, filters,
supply and return ductwork, grilles and diffusers).The
• The SP varies as a square of the RPM:
SP and CFM values are used to create the system curve
for the particular system. FIG. 3 represents a fan curve RPM2 2
SP2 = SP1 x
with 2 system curves identified. RPM1
PEAK EFFICIENCY LINE
9
75
M
• The BHP varies as a cube of the RPM:

AX
.H
P
8 50
15
13
HP
00
00
RP
RP
RPM2 3
M
7 40
HP BHP2 = BHP1 x
60
RPM1
HP
STATIC PRESS. – (IN. WG)
6
11
30 00
HP RP
M
5
900
RP
• The SP and BHP are directly proportional to the
25
M
HP
4
20
HP air density:
3 10
HP 10
70 HP
0R
7.5
HP PM Density2 RPM2 2
2 SP2 = SP1 x x
Density1 RPM1
1 50
0R
PM
Density2 RPM2 3
BHP2 = BHP1 x x
50 100 150 200 250 300 350 400 450 500 550 600 650 700
Density1 RPM1
AIRFLOW – CFM (100)
FIG. 2 – CURVE AT VARIOUS RPMs

The fan laws can only be used to project performance
along a specific system curve. Referencing FIG. 3, Point
9 1300
A can be used to project the performance of Point C and
1500 similarly, Point B can be used to project the performance
8
75 MAX. HP
of Point D. Point A cannot be used to predict any other
7 point on the RPM curve, it can only project performance
1100
on the system curve created by Point A.

60
6
50
B
5
40
900 30
4 A
25
20
D
3
2
em
st
Sy
700
15
1
2 ste
m
Sy
500
10
1
7.5
50 100 150 200 250 300 350 400 450 500 550 600 650 700
FIG. 3 – FAN CURVE WITH TWO SYSTEM CURVES
JOHNSON CONTROLS 15
FORM 102.20-QG1 (808)
Variable Air Volume

A common mistake when selecting a fan with variable Select the most efficient fan that can deliver both the
air volume is to assume a fan with VAV will follow a design and minimum CFM requirements. If the initial
constant design system curve (passing through the point selection does not provide sufficient “turn down”, select
0 CFM and 0 TSP) to maintain control. VAV systems the next smallest fan and re-plot the VAV system for the
do not have a constant system line, but rather a range smaller fan and re-evaluate. Typically, the largest fan that
of operating points necessary to satisfy the building can supply the required modulation is the most efficient.
requirements. In VAV systems, the operating point will Each application should be considered individually and
continue to move based on the air modulation and as evaluated to be sure the fan will not be forced into the
the CFM and SP change, the fan is modulated to match unstable region at modulated condition.
the new requirements, developing its own system curve.
For variable speed drive (VSD) applications, the fan
This modulation is accomplished by using inlet vanes,
drive assembly is selected to operate approximately in
variable speed drives or discharge dampers. Before
the middle of the VSD’s range. When selecting a fan to
finalizing the fan selection, plot the new VAV system
be used with a VSD, if the RPM is close to or approach-
curve to confirm the modulation range required does
ing the Class I limit, select the Class II fan. Selection of
not enter into the instability range of operation.
a Class I fan may result in premature bearing failure.
Example
Calculate the minimum CFM and at least 2 arbitrary
points which fall within the stable operating range of
the curve (using equations below) and plot these points
along with the design points to create the new VAV
system. (See FIG. 4.)
Design CFM = 40,000 CFM = CFMd

Design TSP = 4.5 in WG = SPd
Static Pressure Control Point = 1.25 in WG = SPd
1st: Calculate the Minimum CFM:
SPS 1.25
Min CFM = CFMd x = 40,000 x = 10,517
2
CFMd 40,000 2
√ SP1 x
CFM1
+ SPS – SPd
√ 3 x
15,000
+ 1.25 – 4.5
where: CFM1, SP1 = arbitrary point located on surge line

Min CFM = 10,517
2nd: Calculate the Arbitrary Points:
30,000 CFM 20,000 CFM

where: CFM2 = 30,000 where: CFM3 = 20,000
CFM2 2 CFM3 2
SP2 = x (SPd – SPs) + SPs SP3 = x (SPd – SPs) + SPs
CFMd CFMd
2
30,000 2 20,000
SP2 = x (4.5 – 1.25) + 1.25 SP3 = x (4.5 – 1.25) + 1.25
40,000 40,000
SP2 = 3.1 SP3 = 2.1
16 JOHNSON CONTROLS
FORM 102.20-QG1 (808)

9
15
13
00
00
R
RP
PM
M
7
1100
RPM
75
M
AX
.H
P
5 .
Pt
30 n
HP sig
25 De
300 HP
RPM
4
50
60
40
20
HP
HP
HP
HP
3 10
HP
2
Static Pressure
Control Point
1
MODULATION
RANGE
Minimum CFM Design CFM

50 100 150 200 250 300 350 400 450 500 550 600 650 700
FIG. 4 – FAN CURVE AT VARIOUS RPMs
Solution Component Temperature Margins • Pre-filters - 150°F.

• Standard motors (Class B Insulation) -104°F. • High Efficiency Filters - 200°F.
• Motors with Class F Insulation -140°F. • Fan Bearings - 120°F (FC), 180°F (AF)
• Power Wiring - 140°F. • Gasketing - 200°F
• Controls & Control Wiring - 140°F. • Foam - Flash Point: 415°F (213°C)
Fan Motor Heat (MBH)

HEAT Horsepower
5 7.5 10 15 20 25 30 40 50 60 75 100
Fan Motor 2.8 3.6 4.4 6.2 7.5 8.7 9.4 13.0 16.0 19.0 21.0 25.0
Fan 12.7 19.1 24.5 38.2 51.0 63.6 76.3 102.0 127.0 153.0 191.0 254.0
Fan & Fan Motor 15.5 22.7 28.9 44.4 58.5 72.3 85.7 115.0 143.0 172.0 212.0 279.0
JOHNSON CONTROLS 17
FORM 102.20-QG1 (808)
COIL OPTIONS
Flexibility and Performance illustrate the variety of coils Coil Performance is certified in accordance with ARI
which are available to meet every application. These Standard 410.
1/4" FPT PLUGGED
carefully engineered coils are designed for an optimum VENT FITTING
Chilled water / Hot water

balance between air pressure drop and heat transfer
coefficient, to allow the maximum amount of cooling
or heating capacity without the added expense of high
air-pressure drops. The coil designs are subjected to
constant extensive evaluation studies comparing dif-
ferent fin corrugations with various tube arrangements.
The Johnson Controls/YORK Equipment Engineer in
your area will welcome the opportunity to assist you RETURN
SUPPLY
with your coil applications.
Cooling Coils – Water and Direct Expansion Direct expansion (DX) SUPPLY
RETURN
Solution optimizes coil performance with customized coil

options. Solution coils are offered in a wide variety of
types, sizes, arrangements and materials. Coil software
optimizes capacity and pressure drop requirements.
AHU Chilled water cooling coil

• Available in CC, VC, MZ segments
AHU Hot water heating coil

• Available in CC, VC, HC, MZ segments
AHU (DX) Direct Expansion cooling coil

• Available in CC, VC, MZ segments
Notes & Options
Hand of Unit determines connection side of coil. See page 21.
Header material: Fin Spacing:

• Copper • A vast range of fins per inch available
• Red Brass Fin Coatings: (Coatings reduce max face velocities)
Connector material: • Electro-fin
• Red brass • Phenolic
• Steel Coil Casing:
Connection Type: • Galvanized
• MPT • Stainless Steel
• Grooved Choice of heat transfer medium:
Fin type: • Water, Glycol (Ethylene glycol coils are ARI
• 5/8” tube: Sine or Flat certified)
• 1/2” tube: Sine corrugated only • DX – (a variety of refrigerants to choose from)
Fin Material & Thickness:
• Aluminum - 0.006”, 0.008”, 0.010”
• Copper - 0.006”
18 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Heating Coils – Integral face and bypass

Integral face and bypass coils have alternating channels Steam or Hot Water
of heat transfer surface and bypass zones. The air flow
is directed over the heat transfer surface or through the
by-pass zone by modulating dampers that are integral
with the coil construction.
Integral face and bypass coil (IFB/VIFB)

• Coils are available in the ‘IC’ segment
• Tubes either Vertical or Horizontal
• Coils for maximum freeze protection
INTEGRAL FACE & BYPASS (IFB) COIL
• Hot water or Steam coils
• Multiple rows deep
Notes & Options

Coil Style: Rows: Fin Material:
• IFB • 1,2,3,4 • Aluminum
• VIFB Connection: Fin Spacing:
Coil Type: • SCH 40 pipe • A range of fins per inch available
• Water (Glycol) Thermostat: Coil Casing:
• Steam • None • Galvanized
• Electric
Heating Coils – Steam Distributing

The construction of a Steam Distributing Coil is entirely Steam Distributing - 1” diameter tube
different than that of a Standard Steam.
• Available in CC, VC, HC, MZ segments
Everyplace that you see an outside tube or header, there
is an inside tube and header that you can’t see. Steam is • A vast range of fins per inch available
distributed through these inside tubes and headers and • Multiple tube wall thickness options
slowly released to the outside tubes as the steam turns
to condensate. The condensate then flows back down Steam
the outside tubes in the same direction that the entering
steam comes from. The idea is that all the steam in the
inside tubes keeps the condensate in the outside tubes
from freezing when air passes across the coil at less
than 32ºF. However, under exactly the correct conditions,
even steam distributing coils can freeze.
JOHNSON CONTROLS 19
FORM 102.20-QG1 (808)
COIL OPTIONS
Typical Application of Air Handling Coils solenoid valves in the refrigerant liquid lines, which are
energized to shut-off the flow of refrigerant to part of the
Heating Coils coil. There are several problems with the application of
VAV to a direct expansion (DX) coil which require the
Heating coils can use steam or hot water to add heat
designer to take special precautions when considering
to the air stream. In a cooling-only VAV system, the
this system. First, the balance point temperature for
heating coil is generally placed in the ‘preheat’ position
the DX coil will change as the air flow rate changes.
between the filters and cooling coil. The preheat coil
Assuming constant coil capacity, reducing the CFM will
can be omitted in this system if the minimum outside
reduce the suction temperature and pressure, making
air requirement is low and would not result in a mixed
close control of air temperature difficult. In addition,
air temperature below 50ºF to 55ºF.
compressor unloading at reduced load will cause step
Heating coil capacity is controlled by means of a modu- changes in capacity and suction temperature, which
lating control valve in the water or steam piping. The can cause hunting in the flow control loop. In short, the
control valve position is usually controlled by means of use of variable air flows with a DX coil requires careful
a thermostat in the supply air duct in sequence with the consideration of the effect air flow changes make to the
cooling coil control valve. system. Balance point temperatures must be carefully
considered.
Cooling Coils
Design Considerations
Cooling coils remove both sensible and latent heat from
the mixed air and can use chilled water, chilled brine, or In order to insure predicted coil performance, air distri-
refrigerant as the cooling source. In the case of chilled bution must be uniform. There are two design checks
water, the supply water temperature generally ranges for this:
from 42ºF to 50ºF, depending on the latent load to be
1. ‘45 degree rule’ – This rule states that the perfor-
removed. Brine or a solution of ethylene or propylene
mance of the coil will not be affected as long as the
glycol in water is traditionally used at temperatures of
diffusion angle from the most restrictive block-off to
32ºF to 40ºF for applications in which piping is exposed
the finned portion of the coil is 45 degrees or less.
to freezing temperatures. Control of the cooling coil ca-
This rule holds true unless there are unusual flow
pacity at the air-handling unit is achieved by means of
fields, caused by such components as upstream
a two-way ‘throttling’ or three-way ‘mixing’ control valve.
fans or mixing boxes where not applied properly.
In VAV systems, a supply duct thermostat is typically
used to modulate the control valve so as to maintain 2. ‘Uniform pressure rule’ – This rule states that the
a constant temperature of air leaving the unit, usually performance of the coil will not be affected as long as
55ºF to 60ºF. the maximum difference in upstream, downstream,
and combined static pressure due to local velocity
When refrigerant is used as the cooling source, it enters
pressure at any one point on the coil compared to
the coil in liquid form from a condensing unit and pro-
another point that does not exceed 10 percent of
vides cooling by a process called ‘direct expansion’. The
the pressure drop through the coil. The basis for
liquid refrigerant evaporates as the warmer air moves
this rule is that the flow rate through the coils at any
across the coil, removing heat from the air during the
one point is a function of the local upstream and
process. The evaporated refrigerant is then compressed
downstream pressures, and if pressure differences
in the condensing unit, which also houses the condens-
are small, distribution will be uniform.
ing coil where the heat is rejected to the outside. Control
of the coil capacity is typically by means of a series of
Literature Reference — See “DX Piping Guide” – Form 050.40-ES2
20 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
SOLUTION SEGMENT IDENTIFICATION
FAN SEGMENTS HEAT SEGMENTS ACCESSORY SEGMENTS

• FS – Supply • IC – Integral Face & Bypass Coil • VP – Vertical Plenum
• Forward Curved • IG – Indirect Gas Fired Furnace • DP – Discharge Plenum
• Airfoil • EH – Electric Heater • TN – Turning Plenum
• Industrial Airfoil • DI – Diffuser
• SWSI Plenum ENERGY RECOVERY • XA – Access segment
(Belt and Direct Drive) • ER – Energy Recovery • AB- Air Blender
• FR – Return • EB – External Bypass
• Forward Curved FILTER SEGMENTS • IB – Internal Bypass
• Airfoil • FF – Flat Filter (2” or 4”) • FD – Face Damper
• Industrial Airfoil • AF – Angle Filter (2” & 4”) • AT – Attenuator
• SWSI Plenum • RF – High Efficiency Filter • HM - Humidifier
(Belt and Direct Drive) • Rigid Filter (12”) • UV - UVC Lamps
• FE – Exhaust • Bag Filter (21”)
• Forward Curved • Mini-Pleat Filter (4”)
• Airfoil • HF – HEPA Filter
• Industrial Airfoil
INLET SEGMENTS
COIL SEGMENTS • MB – Mixing Box
• CC – Cooling Coil • FM – Filter/Mixing Box
• HC – Heating Coil • EF – Filter/Economizer
• VC – Vertical Coil • EE – Economizer
• MZ - Multizone • IP – Inlet Plenum
• VE – Vertical Economizer
• VF – Vertical Filter/Economizer
Unit & Coil Hand Identification
FAN SECTION
RIGHT
REAR
RIGHT HAND (RH)
COIL CONNECTION
LEFT HAND (LH)

COIL CONNECTION
RETURN AIR
OUTSIDE AIR
LEFT
INLET SECTION
DRIVE HAND AND COIL HAND DETERMINED
BY FACING THE INLET SECTION
FRONT
JOHNSON CONTROLS 21
FORM 102.20-QG1 (808)
SINGLE FAN SEGMENT – FS, FR AND FE
Fan Applications
Fan segments are available as supply, return and or exhaust applications. Unit configurations have a segment op-
tion of utilizing a single fan or a dual fan arrangement. Isolation consists of 1" or 2" springs with a seismic snubber
option. Thrust restraints and OSHA belt guards are available as required.
Double-width/Double-inlet (DWDI) Bearing options for fans with lubricating bearings: (refer
• Forward Curve or Airfoil centrifugal to Notes & Options)
• Belt Driven • Extended Lube Line
Single-width/Single-inlet (SWSI) • External Lube Line
• Airfoil plenum
• Belt Drive or Direct Drive
In most fan systems a segment with a single fan is

adequate for the required system design and rating.
Methods of control can vary and may include dampers
or variable speed drives. Also included in a single fan
design may be the allowance for future expansions.
In some situations, there may be a need for a system design using multiple fans in a cabinet. The following are some
reasons to consider a dual fan arrangement:
Dual Fan Considerations 4. Critical systems are often equipped with redundant
or back-up fans in case of a fire or accident or some
1. One fan may be too large and not fit into the desired
other emergency that requires a sudden increase in
space, or it may weigh too much if supported on
flow. Redundant fans are also used to eliminate down-
upper levels.
time during fan maintenance.
2. The required operating range of the system may
5. Some systems for process applications may require
necessitate multiple fans instead of one large fan
pressures that are greater than a single fan can pro-
controlled over a wide operating range.
duce or when noise may be a special concern.
3. Multiple fans for capacity control may be more eco-
nomical if cost of operation is critical, especially at
very low flow rates for long time intervals.
Dual Fan Applications

Solution dual fan application methods include 50/50 where both fans operate together to share the load equally or
100/100 where only one fan at a time is in operation.
• In a 50/50 application, the failure of one fan will re-

sult in a condition where the other fan will continue
to operate. The single fan will provide partial load
capabilities
• In a 100/100 application, the failure of one fan will
result in the operation of the other (standby) fan to
provide full capacity
Literature Reference — see Application Guide ‘AHU Dual Fan Options’ - Form 102.20-AG17
22 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Door and Discharge Locations

Fan and fan motor may be oriented in the fan
segment. Consideration must be given to which
orientation is used where. Upstream/downstream
usage follow.
Where Doors are used:

Rear/rear-inverted discharge – Upstream
Top/bottom discharge – Downstream
Front/front inverted discharge – Downstream
Top-inverted/bottom-inverted discharge –
Upstream
REAR (R) FRONT (F) TOP (T) BOTTOM (B)
HINGES
HINGES
DOOR HINGES HINGES
DOOR DOOR DOOR
REAR INVERTED (RI) FRONT INVERTED (FI) TOP INVERTED (TI) BOTTOM INVERTD (BI)
HINGES
HINGES
DOOR HINGES HINGES
DOOR DOOR DOOR
AIRFLOW
JOHNSON CONTROLS 23
FORM 102.20-QG1 (808)
SINGLE FAN SEGMENT – FS, FR AND FE
Double-width/Double-inlet (DWDI) Options – Belt Drive

Fan and fan motor may be oriented in the fan segments as shown. Consideration must be given to which orientation
is used where. Upstream/downstream images shown below.
Motor Beside Motor Behind
Notes & Options (DWDI)
1. If a discharge plenum is immediately downstream of a fan Fan type available

section and the discharge plenum has a top discharge, the fan • Forward Curve centrifugal
section will be rear inverted discharge.
• Airfoil centrifugal
2. If the discharge plenum has a rear, side or bottom discharge,
the fan will be rear discharge. Class I (S) construction
3. When a diffuser is ordered immediately downstream of a fan • Permanently sealed bearings

section, the fan will be rear or rear inverted discharge. • Fan sizes: 7x7 thru 18x18 (Forward Curve)
4. Door width is sized to remove max HP motor with connection Class 1 Construction
box removed. • Lubricating bearings
• Fan sizes: 20x15 thru 40x40
NOTE: Doors follow motor location. See door locations illustration Class II construction
on page 23.
• Lubricating bearings
Thrust restraints are optional for rear and front discharge airfoil fans
only.
• Not available for FC fans.
• Required for AF with TSP over 6”
24 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Single-width/Single-inlet (SWSI) Options

Fan and fan motor may be oriented in the fan segments as shown. Consideration must be given to which orientation
is used where. Upstream/downstream images shown below.
Belt Drive Direct Drive
Notes & Options (SWSI)
1. The plenum fan segments can accommodate multiple duct 3. Fan discharge locations - rear, front, bottom, top, left and right.
outlets, thus reducing the amount of field duct work and 4. Single Width, Single-Inlet (SWSI) air foil plenum fans are
transitions. available as Class I, II & III. (with lubricating bearings)
2. When any filter segment (EF, FM, FF, AF, RF, or HF) or coil 5. Thrust restraints are required with TSP over 3”.
segment (CC or HC) is located upstream of a FS-SWSI,
FR-SWSI or FE-SWSI, sufficient transition length will be
required between the FS segment and the filter segment.
JOHNSON CONTROLS 25
FORM 102.20-QG1 (808)
DUAL FAN SEGMENT – FS, FR AND FE
Double-width/Double-inlet (DWDI) Options – Belt Drive
Fan type available:

• Forward Curve centrifugal
• Airfoil centrifugal
Class I (S) construction
• Fan sizes: 7x7 thru 18x18 (Forward Curve)
Class 1 construction
Motor Behind
Class II construction
DWDI motor location – Behind only
Notes & Options
Access doors are provided on both sides of the segment. • DWDI option is mounted on fan discharge.
• Allow sufficient access-to and clearance-around the segment • Note: Not available with fan exhaust (FE)
for motor removal from either side. • Option is required with 100 %/100 % method.
Separation Panel Option Options include (depending on type of fan):
• Optional safeguard when servicing requires that the system be 1. Manual sliding panel
in a running status. A separation panel is positioned between
the fans. 2. Back-draft damper with counter balance
Flow Isolation Options 3. Mechanical Control damper
• Optional isolation method to prevent air from an energized fan

going back through a fan that is not energized.
DUAL FAN DUAL FAN DUAL FAN

WITH NO WITH SLIDING WITH DISCHARGE
DAMPER PANEL DAMPERS
DAMPER
OPTIONAL SLIDING OPTIONAL OPTIONAL

ISOLATION WALL ISOLATION ISOLATION
FS WALL WALL
DAMPER
WALL
DAMPER
OPTIONAL SLIDING OPTIONAL OPTIONAL

ISOLATION WALL ISOLATION ISOLATION
FR WALL WALL
DAMPER
WALL
NOTES:
OPTIONAL 1. DAMPER OPTIONS ARE ONLY

ISOLATION
FE WALL AVAILABLE FOR FRONT/FRONT INVERTED/

REAR/REAR INVERTED DISCHARGE.
DIRECTION OF AIRFLOW
2. DAMPERS OPTIONS ARE NOT

AVAILABLE FOR TOP/TOP INVERTED/
BOTTOM/BOTTOM INVERTED DISCHARGE.
26 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Single-width/Single-inlet (SWSI) Options – Belt-Drive or Direct Drive
Fan type available:

• Standard Airfoil (AF) 10" – 30"
• *Industrial Airfoil (AF) 12" – 30"
• Class I, II, *III
SWSI motor location:
• 10" to 16" fans - behind motor only
• 18" to 30" fans -top motor only
• Fans with top motor location will require thrust
restraint
Notes & Options
Access doors are provided on both sides of the segment. • SWSI option is mounted on fan inlet.
• Allow sufficient access-to and clearance-around the segment • Note: Not available with fan exhaust (FE)
for motor removal from either side. • Option is required with 100 %/100 % method.
Separation Panel Option Options include (depending on type of fan):
• Optional safeguard when servicing requires that the system be 1. Manual sliding panel
in a running status. A separation panel is positioned between
the fans. 2. Back-draft damper with counter balance
Flow Isolation Options 3. Mechanical Control damper
• Optional isolation method to prevent air from an energized fan

going back through a fan that is not energized.
DUAL FAN DUAL FAN DUAL FAN

WITH NO WITH SLIDING WITH INLET
DAMPER PANEL DAMPERS
DAMPER
OPTIONAL
ISOLATION OPTIONAL
WALL SLIDING ISOLATION
FS
WALL WALL
OPTIONAL DAMPER
ISOLATION
WALL
DAMPER
OPTIONAL
OPTIONAL ISOLATION
WALL SLIDING
INLET
ISOLATION
WALL
FR WALL
OPTIONAL DAMPER
ISOLATION
WALL
1 WHEEL
DIAMETER
OPTIONAL
ISOLATION
FE WALL
DIRECTION OF AIRFLOW
JOHNSON CONTROLS 27
FORM 102.20-QG1 (808)
FAN SEGMENT – FS, FR AND FE
SWSI Plenum vs. DWDI Housed Fan Application Velocity Profile:

SWSI Plenum airfoil fans offer superior performance Due to the relatively small outlet/blast area of housed
for many applications. Typical concerns with fan per- DWDI fans, an air diffuser must be applied to the dis-
formance are efficiency, noise, and air velocity profile charge of the fan to obtain an acceptable velocity profile
through components. Plenum fans offer advantages through the next component. Air diffusers add static
for all three concerns. Additionally, these fans provide pressure which decreases fan efficiency and increases
flexibility with outlet configurations, reduced mechanical fan noise levels. SWSI plenum fans positively pressurize
space footprint, and the benefit of direct-drive. the entire cabinet, they do not require a diffuser with its
associated performance losses.
Efficiency:
Outlet Flexibility:
DWDI housed fans use a scroll to increase their effi-
ciency. However, optimizing this fan requires a process SWSI Plenum fans serve to pressure the entire fan ple-
referred to as “static regain”. Housed fans are tested num, allowing for multiple duct take-off from the AHU.
with an outlet duct of 2.5 to 3.5 times the wheel diam- Additionally, these openings can be tailored to match
eter in length. This outlet duct allows the “static regain” virtually any duct configuration, be it rectangular or round
process, where velocity pressure is converted to static / flat-oval with bellmouth fittings for improved acoustic
pressure. Housed fans applied without this outlet duct and optimized pressure drop performance.
will require a system effect factor (SEF) which decreases
the fan efficiency. Housed fans in blow-through positions Mechanical Space Optimization:
will also require an air diffuser which decreases the ef-
A housed DWDI fan requires a straight run of duct per
ficiency further. The combination of these two system
AMCA guidelines at the outlet of the fan before elbows
effects brings even the best housed DWDI airfoil fan
can be applied. This constraint imposes restrictions on
efficiency to, or below that, of the SWSI plenum fan,
duct layout and mechanical space design which gener-
thereby eliminating the benefit of the fan scroll.
ally increase overall footprint requirements. The ducted
take-offs from pressurized plenums, as in the case of
Noise:
a SWSI plenum fan, does not have a requirement for a
Plenum fans have the benefit of effectively utilizing the straight run and affords greater flexibility to the architect
entire unit as the fan housing, which offers superior at- and engineer in ductwork design.
tenuation. The same factors that decrease the housed
fan’s efficiency discussed above also increase the noise Direct-Drive Benefit:
level of the housed fan. Also, since the SWSI plenum
Specialty housed DWDI fans can be used in direct-drive
fan has no scroll, typically there is room within the air
arrangements, where the fan wheel is directly mounted
handling unit for a larger wheel (33” SWSI plenum vs. 27”
onto the motor shaft, most-typically, housed fans are
DWDI housed, for example), which generally produces
driven by a belt and sheave system. Belt-drive systems
better sound characteristics. For design pressures at or
typically allow for 3-5% of efficiency loss and impose
below 6.00 in. W.C., it is very common to see supply air
maintenance requirements not present in direct-drive
sound power levels lower when using a SWSI plenum
systems. Additionally, belts wear and give off debris in
airfoil fan instead of the DWDI housed airfoil fan. Ad-
the form of belt dust. Anymore, discerning engineer’s
ditionally, perforated liners may be used in plenum fan
apply direct-driven SWSI plenum fans with VFD’s
sections for greater attenuation.
for efficient variable air volume duty and trouble-free
maintenance.
28 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Fan Motor Control Methods

Motor control options can be explained as any one of the 3 items described below.
Disconnect • Low Cost

This is a device for the source of power (line voltage • Constant Volume
as provided through the building electrical utility) • No BAS control needed
from the controlled device (motor).
Across-the-line Starter • Higher Cost
Motor Controller will provide a start / stop operation • Constant Volume
of a motor. An integral disconnect (shall incorporate • Start/Stop controlled remotely
a “lockout/tag-out” system) shall provide discon-
• Thermal Overload Protection
necting of “line side” power from the electrical utility
system. • Under/over Voltage Relay
• Disconnect Option - Fused only
The motor controller will also contain the proper
short circuit and thermal overload protection for the Indoor Enclosure - NEMA 3R
motor that it is controlling. Indoor Voltages - 200, 208, 230, 380, 460, 575
Outdoor Enclosure - NEMA 3R

Outdoor Voltages - 200, 208, 230, 380, 460, 575
Variable Frequency Drive (VFD) • Highest Cost
The Air-Modulator type controller varies speed of the • Variable Volume
motor by pulse width modulation of the alternating • Start/Stop controlled remotely
current waveform.
• Integrated basic unitary controller (can also integrate with BAS)
• Comprehensive Protection
An integral disconnect (incorporates a “lockout/tag-
• Disconnect Options -Fused, Non-fused, or None
out” system) provides disconnecting of “line side”
power from the electrical utility system.
Indoor Enclosure - NEMA 1
This motor controller will also contain the proper Voltages - 200, 208, 230, 460
short circuit and thermal overload protection for the
motor that it is controlling. Outdoor Enclosure - NEMA 3R
Outdoor Voltages - 200, 208, 230, 380, 460, 575
Literature Reference — See Engineering Guide – ‘Air Modulators’ – Form 100.42-EG1
JOHNSON CONTROLS 29
FORM 102.20-QG1 (808)
COIL SEGMENT – CC, HC AND VC
Cooling Coil – (CC)

When cooling 100% OA there are precautions required.
Summer design conditions are such that when air is
cooled down to normal coil leaving temperatures, there is
a considerable amount of condensate generated. Many
applications suggest cooling coils should be selected
for an air velocity under 500 FPM. If the unit is selected
as a 100% OA application, the drainage area for larger
face area coils will be increased to properly compensate
for the probable condensate.
Notes & Options
Coils Door
• A combination of Water and DX coils in the same segment • Usual door location is drive side
requires all coils to be of the same tube diameter. • With pipe chase, the door is always opposite the pipe chase
• Multiple Water coils configured in the same segment must be IAQ drain pans material options:
of the same tube diameter.
Liner – Galvanized or Stainless Steel
• Steam coils may be configured with 5/8” tube coils. A spacer
must be used between a steam coil and any water coil or DX
coil.
Headers
• Usual header location is drive side.
• All headers in the same segment must exit the unit on the
same side.
Heating Coil – (HC)

When heating only is required the heating coil segment
is an excellent minimally sized housing which shall ac-
commodate a single heating coil. Coils are offered with
left or right hand connections. Coils will be individually
mounted and easily removable.
Coil segment panels (side panels and top panel) shall
be easily removable to allow for removal and replace-
ment of coils, without affecting the structural integrity
of the unit.
Notes & Options
Coils Doors
• Only hot water and steam coils are available in the HC seg- • Doors are not available.
ment. Drain pans
• Only one coil (hot water or steam) is permitted per segment. • Auxiliary drain pan is optional.
Headers • Usual drain location is header side.
• Usual header location is on the drive side. • The drain is always opposite the pipe chase.
Literature Reference — See Service Guide – ‘Field Assembly ad Disassembly Indoor/Outdoor’ –

Form 102.20-FA1 & Installation Manual Form 102.20-NOM1
30 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Vertical Coil – (VC) SIDE VIEW
This segment shall provide for a 90-degree change in

airflow direction from horizontal to vertical, after passing
air through the coil space.
FS
Coils are configured for horizontal air flow to minimize FAN
SEGMENT
segment length. Drains pans are extended to assure
complete condensate drainage and coil access. Coil
segment panels (side panels) shall be easily removable
to allow for removal and replacement of coils, without
affecting the structural integrity of the unit. VC
SEGMENT
AIRFLOW
LEFT HAND SHOWN
RIGHT HAND OPPOSITE
CONDENSATE DRAIN
CONNECTION 1 1/4" MPT
Notes & Options
Coils Doors
• All coils located in the same coil segment must have the same • Usual door location is on the drive side.
coil hand. • Doors are always last in the air stream of the segment
• Multiple Water coils configured in the same segment must be • With pipe chase, the door is always opposite the pipe chase
of the same tube diameter.
• A combination of Water and DX coils in the same segment
requires all coils to be of the same tube diameter. Drain pans
• The steam coil is available for use in the VC segment. Steam • IAQ drain pan liner - Galvanized or Stainless Steel
coils may be configured with 5/8” tube coils. A spacer must be • Usual drain location is on header side
used between a steam coil and any water coil or DX coil. • With pipe chase, the drain is always opposite the pipe chase
Headers
• Usual header location is on the drive side.
• All headers in the same segment must exit the unit on the
same side.
JOHNSON CONTROLS 31
FORM 102.20-QG1 (808)
STAGGERED COIL OPTION – CC, HC, AND VC
Staggered Coil configurations are available as an option for both the indoor and outdoor Solution® units. Angled Wall
or Back-to-Back configurations are available in both heating and cooling coil segments.
Angle Wall
Staggered coil design increases coil face area and al-
lows increased CFM without having to increase cabinet
size.
Notes & Options
Coils follows the ”primary” side of the unit.

• A staggered coil can not be combined with a non-staggered Headers
coil in the same segment. • Coil connections can be on the same side or opposite sides.
• Each coil bank will be located over a drain pan. • Optional factory extended piping connections for each coil to
• Not available as a reduced face coil option. the exterior of the unit.
Controls • Optional insulation for extended piping.
• Optional control valve and valve jack (manifolded together • Extended piping does not apply to DX coils.
external of unit).
Drain pans
• Pan connection hand follows coil hand except for outside units
where the drain connection is opposite the coil hand.
• If coil connections are on both sides, the drain pan connection
Back-to-Back
Staggered coil design is specifically for a reduced coil
pull distance and for opposite side connections. Two
shorter coils will be used in place of one longer coil.
Notes & Options
Coils Drain pans

• A staggered coil can not be combined with a non-staggered • The drain pan connection follows the ”primary” side of the unit.
coil in the same segment. Headers
• Not available as a reduced face coil option. • Coil connections can be on the same side or opposite sides.
32 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Multi-zone Segment – (MZ) HOT DECK DAMPER

(FULL WIDTH)
MZ heating and air conditioning units offer design and HOT DECK
application advantages over various smaller single
zone units. The Solution unit is designed to carry on
that tradition by including a MZ segment into the design
of the unit. CC XA DI DWDI < AIR FLOW
-OR-
(COLD DECK)
SWSI < AIR FLOW
MZ and Dual Deck air-handling units can be configured COLD DECK DAMPER
(FULL WIDTH)
for heating and cooling, or cooling and ventilation, or

ventilation and heating applications.
Rear or Top discharge MZ configurations:
• The bottom tier is the cold deck and contains a
diffuser and a cooling coil space.
• The top tier is the hot deck and contains a heating
coil mounted horizontally at the upstream side of
the hot deck.
Air enters the diffuser then splits into two streams.
• One stream turns up through the hot deck coil
and exits the rear or top through the hot deck
damper.
• The other stream continues horizontally through
the cooling coil and exits the rear or top through
the cold deck damper.
The MZ unit is optionally available less the zone damp-
ers for use on dual duct or other blow-thru systems. If a
hot deck opening is not required, it may be blanked-off
in the field.
Notes & Options
The MZ segment is for indoor applications only and will be the last Discharge options:
segment in air-stream. • Top with damper or without damper
Air pressure drop balance plates shall be used to equalize pressure • Rear with damper or without damper
drop across the hot and cold deck coils when required.
Door is optional for cold deck.
Literature Reference — See Application Guide – ‘Multizone Application of Solution Units’ – Form 102.20-AG12
JOHNSON CONTROLS 33
FORM 102.20-QG1 (808)
HEATING SEGMENTS
Integral Face & Bypass – (IC) Applications ideally suited for:

The Integral Face & Bypass coil controls air temperature 1. Make-up Air
while full steam pressure or water flow is maintained in
2. Combustion Air Make-up
the coil at all times. The temperature of the discharge
air is controlled by proportioning the entering air through 3. Penthouse units
the multiple heating and by pass channels.
4. Air conditioning preheat and IFB
heating/ventilating units.
RACEWAY
WIREWAY
AIRFLOW
LEFT HAND SHOWN
RIGHT HAND OPPOSITE
VIFB COIL CONECTIONS

Features & Benefits:
IFB COIL CONNECTIONS
• Maximum freeze protection

• Constant volume
• Minimum temperature
J L K
override
LE
• Minimum stratification VIFB
• Accurate temperature
control
Notes & Options
1. Coil connections must be located opposite the access door. Doors:

2. All piping to be supplied by field, coil connections are internal Access doors and viewing ports must be located in adjacent seg-
from factory. ments.
3. Optional pipe chase with outdoor units A door is required in the immediate downstream segment from the
4. Pipe chase is not intended for trapping or piping, but for the IC segment.
connections only. Auxiliary Drain pans:
Headers: An auxiliary drain pan is optional.
Usual header location is on the drive side. Header location must Usual drain location:
be opposite the access door. • With pipe chase, the drain is always opposite the pipe chase
Coils: • IFB on header side
Only hot water and steam applications are available for this seg- • VIFB on left side of the unit
ment.
34 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Indirect Gas-Fired Furnace – (IG)
HEAT EX.
CONTROL
PANEL
DOOR
I.D. FAN
Notes & Options
The IG segment must be positive pressure. (Fan segment is not al- Furnace includes a series stainless steel primary heat exchanger. A
lowed downstream of the IG Segment.) secondary stainless steel heat exchanger is also included.
Furnaces in VAV applications are designed to be used only with 100% – An access door is required upstream of any IG segment.
supply fan airflow. – Gas pipe train options are available
– Use of furnace in reduced airflow operation may result in seri- The IG segment pipe chase is a single pipe chase that covers only
ous damage to equipment and may be hazardous. the IG segment.
– Indirect Gas-Fired Furnace Maximum Temperature rise = 90F – The pipe chase is not intended for trapping or piping, but for
– Indirect Gas-Fired Furnace Maximum A.P.D. = 2.00” W.C. the connections only.
– The Maximum Temperature at the IG segment discharge = – Pipe chase enclosure is optional for indoor units and required
190F for Outdoor units.
JOHNSON CONTROLS 35
FORM 102.20-QG1 (808)
HEATING SEGMENTS
Turndown Examples and Guidelines – (IG) Choosing Considerations

When choosing the proper turn down three issues should
Description
be considered.
Indirect Fired Gas Heater section consists of the stain-
1. Greater modulation provides improved temperature
less steel primary and secondary heat exchanger with
control. If the furnace is modulated to its minimum
the power burner design. The basic design allows the
fire position, and controls determine there is too
power burner to inject the correct ratio of air and gas into
much furnace capacity, then the furnace is staged
the primary heat exchanger where the main combustion
on and off, on carefully chosen time delays, to satisfy
occurs. The heated products of combustion then pass
the light load heating requirements. The 3-1 option is
through the multiple secondary tubes heating each tube
generally sufficient particularly if design temperature
for maximum heat transfer. The products of combustion
rise does not exceed 30-40 degrees.
then pass to the inducer draft fan and through the flue.
The air is heated by passing around the primary and 2. The greater the range of modulation the greater
secondary tubes for optimal heat transfer. The heater the cost.
is designed for 80% efficiency.
3. Experience requires that a furnace should not turn
• The furnace comes wired with all necessary down to a temperature rise less than 5-8 degrees.
safety controls and valves installed.
Greater modulation decreases the flue stack tempera-
• The controls vary based on the BTU level and ture at low fire, increases the amount of condensation,
Insurance Requirements selected. and can decrease the life of the heat exchanger even
though all Solution furnaces utilizes a stainless steel
• These units are designed to handle Natural Gas
primary and stainless steel secondary heat exchanger
as a standard.
tubes along with condensate drains.
• The gas pressure available at the unit needs to be
The condensate line must be adequately sized, trapped,
considered when ordering the equipment.
along with drainage of the condensate per local code.
Equations:
• BTU Output Required = CFM x 1.08 x Tempera-
ture Rise Required
• BTU Input = BTU Output ÷ .80
The Solution furnaces are available with burner firing
arrangements:
• 3-1 MODULATION: The burner will modulate for
100% - 33% of full fire
• 10-1 MODULATION: The burner will modulate
from 100% - 10% of full fire
• 25-1 MODULATION: The burner will modulate
from 100% - 4% of full fire
Literature Reference — See Installation Operation Manual – Form 102.20-NOM1
36 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Electric Heat – (EH)

The EH segment can be installed in either a draw
through or blow through arrangement.
Remote Mounted terminal panels
• An electric heat control panel may be selected as
a remote panel.
• In this case the panel will be shipped separate to
the customer for field installation.
An optional wide access door may be ordered on the
opposite side of the electric heater control panel.
An SCR Controller is available on all heaters with a
height dimension greater than 26.5”.
Delta T = kW x 3160
CFM
Notes & Options
• Electric heaters are of “open coil” construction, with 80% nickel, • All internal wiring shall be stranded copper with 105°C minimum
20% chromium coil elements machine crimped to stainless steel insulation and shall be terminated in crimped connectors or box
terminals and amply supported on ceramic bushing isolators. lugs.
Open coil heaters are furnished with a disk-type, automatic reset • Power and control terminal blocks shall be provided and clearly
thermal cutout for primary over-temperature protection. Heaters marked for all field wiring and shall be sized for installation of
are also being furnished with disk-type, load-carrying manual 75°C copper wire rated in accordance with NEC Table 310-16,
reset thermal cutouts, factory wired in series with heater stages not more than three conductors in a conduit.
for secondary protection.
• Heaters shall be furnished with built-in fuses per NEC. Heaters
• Heaters are rated for the voltage, phase and number of heating with loads greater than 48 amps will be furnished with built-in
stages indicated in the schedule. All three-phase heaters will fusing. Heaters shall be sub-circuited into a maximum of 48
have equal, balanced, three-phase stages. amps per circuit. Low resistance single element fuses will be
• Finned tubular construction - optional mounted in phenolic fuse blocks fitted with extra tension springs
to assure cool connections. Fuses shall be sized at least 125%
of the load.
JOHNSON CONTROLS 37
FORM 102.20-QG1 (808)
HEATING SEGMENTS
Typical Applications SCR steps. This is accomplished by satisfying most

of the heat requirement through the non-SCR steps
An electric heating system will use either an open wire
and then the last portion of the heat requirement is
element or an element encased in a sheathed ceramic
“fine-tuned” by the modulating SCR controller. The
material. For most applications either construction can
SCR step is nominally equal to the KW of a non-SCR
be used, however, in applications with potentially high
step to provide an even transition between steps.
humidity (i.e.100% OA application), the encased ele-
ment will have a longer life expectancy and is recom-
*Special Application Considerations:
mended.
(contact factory for special applications)
Selection of the proper unit, heating load and tempera-
It is always important to ensure the proper control
ture control system is dependent on the application of
method so that the heater effectively treats the required
the unit.
amount of outdoor air regardless of temperature, with-
1. Make-up Air Unit is used for heating 100% OA air out risking over heating and or tripping the low limit
to the indoor design temperature with a typical dis- thermostat.
charge temperature of 55-70° F.
1. In applications where air flow varies and temperature
2. Space Heating Unit is used for heating 100% RA ranges are extreme, the face area of the heater
from the conditioned space to make up for building should be designed for full face simultaneous con-
heat loss. trol, thus avoiding problems of air and temperature
stratification. This is extremely relevant on heaters
3. Combination Make-up Air & Space Heating
with large face areas. The full face control method,
is used to heat OA & RA combined through a
for a partial of fully active electric heat coil, elimi-
mixing box.
nates the concern of air bypass through inactive
circuits. Thus, almost any load split can be safely
Optional Control Methods
achieved.
1. Proportional step control – multi-staging control of
2. With lower airflows under VFD control, one must
circuits
assure there is even air flow across the face area of
2. SCR Controller – a time proportioning type controller the heater. This may require special consideration
that modulates the heater and supplies the exact of the air-inlet position and size, (i.e. inlet to be
amount of power to match the heat demand. Preci- centered on the front of the unit).
sion controlled from zero to 100% in direct response
a. Instability in temperature can easily occur if the
to the modulating thermostat signal system. 100%
variation in the air flow characteristic is exces-
step-less and noise-less operation. *Note – SCR’s
sive. Large temperature variations can occur
are limited to a maximum KW. Multiple SCR’s may
as specific stages and circuits are modulated
be applied to larger heaters. Multiple SCR’s do not
on and off. In extreme cases, this instability can
imply full face control. See “Special Application
cascade and cause extreme over-heating on the
Considerations”.
complete heater face or in spots of the heater
3. Vernier Proportional Control – used on larger KW face due to low-air-flow augmented by unit inlet
heaters where very close heat control is required. opening locations and distance.
The system employs a combination of SCR and non-
38 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Recommended Safety Control Options: EXAMPLE:

A fan relay and an airflow switch provide added protec- Determine whether the minimum air velocity requirement
tion for applications listed above. is met for a 108 kW heater installed for an air handling
unit operating at 18,000cfm at a maximum inlet tem-
– Fan relay provides the advantage of being a posi-
perature of 65°F.
tive electrical interlock between the fan and the
heater. 1. Heating Coil Area = 33 sq. ft.
– Airflow switch is normally used to prevent a 2. kW / sq ft. = 108 kW = 3.3 kW / sq. ft. 33 sq. ft.
heater from operating unless air is flowing.
3. Use top curve (below 80°F inlet air). Find 3.3 kW
per square foot on the vertical axis.
Minimum Air Flows
Read the minimum face velocity required, which
Electric heaters differ from steam or hot water coils in
in this case is 250 feet per minute (fpm).
that the heat output is constant as long as the heater
is energized. Therefore, sufficient air flow must be pro- 4. AHU FV = 18,000 cfm = 545 fpm 33 sq. ft.
vided to prevent overheating and nuisance tripping of
Since 545 FPM exceeds the minimum velocity require-
the thermal cutouts.
ment of 250 FPM, this installation is satisfactory for
The minimum required velocity is determined from the heater operation.
graph on the basis of entering air temperature and watts
Equations: Use these formulas as rough guidelines for
per square foot of cross segmental heating coil area.
estimating purposes only:
EQUATION 1: MBH = kW x 3.412
EQUATION 2: ▲T = kW x 3160
Scfm
EQUATION 3: Actual kW = Rated kW x V actual
V rated
EQUATION 4: Load Amps = kW x 1000
V x 1.732
Literature Reference — See Application Guide ‘Electric Heaters for Air Handling Units’ – Form 102.20-AG4
JOHNSON CONTROLS 39
FORM 102.20-QG1 (808)
ENERGY RECOVERY – ER
Energy Recovery
An HVAC system that utilizes energy recovery is more
energy efficient, improves humidity control, and reduces
peak demand charges.
Solution Energy Recovery wheels:
– Improve building HVAC system performance by
efficiently preconditioning the outdoor air supply.
The ER segment transfers heat & humidity from adjacent
exhaust air & outside air streams.
– Improves HVAC system efficiency up to 40%
Horizontal wheel segment
– Improves de-humidification capacity up to 75%
Thermal performance is certified by the manufacturer
in accordance with ASHRAE Standard 84, Method of
Testing Air-to-Air Heat Exchangers and ARI Standard
1060, Rating Air-to-Air Energy Recovery Ventilation
Equipment
HEATWHEEL MOTOR
Vertical wheel segment
Notes & Options
ER has only one type of configuration – supply air fan draw-thru and Wheel control
exhaust air fan draw-thru for indoor and outdoor applications. • Damper control
1. Indoor - Vertical wheel segment with stacked construction • VFD
a. All doors are usually on drive side with two on top tier
(both sides of wheel) and two on bottom tier (both sides of
wheel). – Auxiliary drain pan – none
2. Indoor and Outdoor - Horizontal wheel segment with single – Purge function – Optional
tier construction
a. Outside Air inlet is located on both sides of segment
b. Access door is usually on drive side for horizontal wheel
segments.
Literature Reference — See Application Guide “Energy Recovery Wheels” – Form 102.20-AG6
40 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
FILTER SEGMENTS – AF, FF, RF AND HF
Application and Options Table

Application: (AF) Options:
Side loading only
– Pre-filter side-load negative pressure – Auxiliary Drain pan options
configuration
– 2” & 4” Low Efficient media
– Single stage filtration
AIRFLOW – 4” High Efficient media
AF - ANGLE FILTER
Application: (FF) Options:
– Pre-filter side-load negative pressure – Auxiliary Drain pan
Side loading only configuration – 2” & 4” media
– Single stage filtration – Low Efficient media
AIRFLOW
FF - FLAT FILTER
Application: (RF) Options:
Rear, Front or side loading
(length includes 2" prefilter)
– Pre filter negative pressure configura- – 2-stage filtration.
tions: – Auxiliary Drain pan
Side-load, front load and rear load
AIRFLOW – 4” & 12” High Efficient Media
– Final filter positive pressure configu- (65%-95%)
rations:
Front-load (upstream access required)
Rear-load (downstream access required)
Side-load
RF - RIGID FILTER
Application: (Bag) Options:
Rear, Front or side loading
(length includes 2" prefilter)
– Pre filter negative pressure configura- – 2-stage filtration.
tions: – Auxiliary Drain pan
Side-load, front load and rear load
AIRFLOW – High Efficient Media (65%-95%)
– Final filter positive pressure configu-
rations:
Front-load (upstream access required)
Rear-load (downstream access required)
Side-load
RF - BAG FILTER
Application: (HF) – Face velocity - maximum 500 fpm
– Pre filter negative pressure configura- – Single stage filtration
Front loading tions: Options:
Front-load (upstream access re-
– Auxiliary Drain-pan
AIRFLOW
quired)
– Media efficiency 99.97% & 99.99%
– Final filter positive pressure configu-
rations: Front-load (upstream access
required)
HF - HEPA FILTER
Caution – Never place a blow-thru final filter segment directly downstream of a cooling coil with a saturated leaving air tem-
perature. Once the relative humidity has reached 100%, adiabatic cooling applies to the expanding air and associated tem-
perature drop. Moisture deposits may form on final filters.
JOHNSON CONTROLS 41
FORM 102.20-QG1 (808)
FILTER SEGMENTS – AF, FF, RF AND HF
Mechanical Air Filters ASHRAE 52.2 Particle Size Ranges
Mechanical air filters remove dust by capturing it on Range Size (in microns) Group
the filter medium, the filter element. A mechanical air 1 0.30 to 0.40 E1
filter is any type of dry media filter. All of the throwaway 2 0.40 to 0.55 E1
air filters used in HVAC systems and Air Handlers are 3 0.55 to 0.70 E1
mechanical air filters. Any man made or natural fiber
4 0.70 to 1.00 E1
filter is a mechanical air filter. This includes HEPA air
filters as well.
5 1.00 to 1.30 E2
Comparing Various Air Filters To MERV Ratings 6 1.30 to 1.60 E2
Dry-media filters exhibit an increase in efficiency as they 7 1.60 to 2.20 E2
collect dirt and dust. A dry media filter is at the lowest 8 2.20 to 3.00 E2
efficiency rating when it is ‘clean’. The increase in ef-
ficiency corresponds to a decrease in open area as the
9 3.00 to 4.00 E3
media collects fibers and particles. In dust critical envi-
ronments the user typically can’t wait for the increased 10 4.00 to 5.50 E3
efficiency. As a result of this type issue, ASHRAE 52.2 11 5.50 to 7.00 E3
defined the minimum efficiency reporting value (MERV) 12 7.00 to 10.00 E3
to describe filter performance. The efficiency of the filter is measured on 12 particle size
The MERV is based on the worst case performance of ranges. The twelve size ranges are then placed in three
a filter through all six stages of dust loading and all par- larger groups (E1, E2, E3) and the percentages in each
group are averaged
ticles 0.3-10 microns. Because the rating represents the
worst-case performance, end users can use it to assure
performance in applications where a maximum particle
count must be maintained over the filter’s entire life. Group 1 Group 2 Group 3
MERV Av. Eff.% Av. Eff.% Av. Eff.%
ASHRAE 52.1 arrestance and dust-spot tests used ei-
Value 0.3 to 1 1 to 3 3 to 10
ther weights or times to generate a ratio, or efficiency.
This efficiency was an easy way to describe a filter’s per- 1 n/a n/a E3<20
formance. Thus, a 50 percent filter would stop a nominal 2 n/a n/a E3<20
50 percent of the particles in the air stream as averaged 3 n/a n/a E3<20
over the test period. Unfortunately, this average over 4 n/a n/a E3<20
time told a user nothing about performance for a specific
5 n/a n/a 20<35
particle size at a specific stage in a filter’s life.
6 n/a n/a 35<50
ASHRAE Standard 52.2 rates filter arrestance differently.
7 n/a n/a 50<70
Standard 52.2 testing protocol includes the reliable and
consistent testing of filter performance on particles of nomi- 8 n/a n/a 70
nal 0.3-10 microns in diameter. This testing provides an 9 n/a E2<50 85
accurate and clear description of arrestance at each stage, 10 n/a 50<65 85
rather than the average produced by Standard 52.1. 11 n/a 65<80 85
12 n/a 80 90
13 E1<75 90 90
14 75<85 90 90
15 85<95 90 90
16 95 95 95
The average is called the Particle Size Efficiency which
is used to determine the Minimum Efficiency Reporting
Value (MERV).
42 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
MERV Analysis The following comparisons are not meant to be definitive:

The required MERV rating for filters will follow directly MERV Particle Filter
from the maximum allowable particle concentrations in Rating Size Applications Type
the three bands of 0.3-1.0 microns, 1.0-3.0 microns and 1-4 >10 um Residential Permanent
3.0-10.0 microns.
Light Commercial Metal
1. A rating of MERV 10 corresponds to 50-65 percent Equipment Foam
efficiency for particles 1-3 microns and above 85 Fiberglass
percent efficiency for particles 3-10 microns.
Poly Panel
2. A rating of MERV 13 corresponds to less than 75 5-8 3 to 10 um Commercial Pleated
percent arrestance efficiency for particles 0.3-1 Filters
Industrial
microns, above 90 percent efficiency for particles
Better Res.
1-3 microns, and above 90 percent efficiency for
particles 3-10 microns. Paint Booth
9-12 1 to 3 um Res. – Best Best
3. A rating of MERV 15 corresponds to 85-95 percent Pleated
arrestance efficiency for particles 0.3-1.0 microns, Commercial
Telecommunica- Rigid Box
above 90 percent efficiency for particles 1-3 mi-
crons, and above 90 percent efficiency for particles tions Rigid cell
3-10 microns. Industrial Bag
13-16 0.3 to 1 um Rigid Cell
4. Ratings of MERV 16 to MERV 20 correspond to
HEPA and ULPA filters. Smoke Removal Bags
General Surgery V-Cell
Note: The entire list of MERV ratings based on particle ar- Hospitals Mini-pleat
restance efficiency is found in Table 12-1 of Standard 52-2. 16-20 0.3 um Health Care HEPA /
ULPA
As an example, if you are concerned with pulling out a
high percentage of molds, mold varies in size from about
4 microns to 40 microns.
• The greatest numbers of mold spores are less than
10 microns in diameter.
• The chart indicates a MERV 8 filter will pull out at
least an average of 70% of the particles down to 3
microns.
• Pleated filters are available in a MERV 11. The
MERV 11 would give you an average of at least
85% mold removal.
JOHNSON CONTROLS 43
FORM 102.20-QG1 (808)
MIXING SEGMENTS & ECONOMIZERS – MB, FM, EE, EF, FD, IP, VE AND VF
Mixing Box/Mixing Segment (MB/FM)

ROOF PANEL
Solution has designed a mixing box (MB) which com- TOP DAMPER
bines fresh air and re-circulated air by means of inter-
connected dampers.
Solution’s space saving combination filter mixing seg-
FRONT DAMPER
ment (FM) offers an angle filter as an integral part of
the mixing segment to economically provide filtering END WALL PANEL
and mixing capability.
Notes & Options
• The MB/FM Segment typically must be the first segment in Hood application – only the following outdoor segments are avail-
direction of airflow. able
• Access doors are optional. • Mixing box (MB or FM) Economizer (EE or EF) outside air
• Auxiliary drain pans optional except when bottom opening is (OA) inlet openings.
selected Hood Options
• Combination filter mixing segment (FM) provides a full-height • Bird screen is standard with all hoods
access door for filter service. • Moisture eliminator is available as an option
• Variable size openings and dampers are optional. Note: When the moisture eliminator option is selected the mois-
• Safety grate option for bottom openings ture eliminator acts as the bird screen. A separate bird screen will
not be required.
Economizer ECONOMIZER WALL
Solution offers numerous economizer configurations

for various ventilation applications. The economizer is
designed with factory packaged controls in-mind. Cor-
rectly set-up economizers will constantly track building
pressurization as well as both indoor and outdoor air
temperatures using transducers, mixed air sensors
and enthalpy control that monitors air temperature and
humidity.
DOOR
DAMPER
DAMPER
ANGLE FILTER ASY

DOOR
Notes & Options
• The EE or EF segment may be first in the air-stream or may Hood Options

be used in conjunction with other segments in an economizer • Bird screen is standard with all hoods
application.
• Moisture eliminator is available as an option
Hood application – only the following outdoor segments are avail-
able with hoods Note: When the moisture eliminator option is selected the mois-
ture eliminator acts as the bird screen. A separate bird screen will
• Fan Exhaust (FE) discharge openings not be required.
• Economizer (EE or EF) exhaust air (EA) discharge openings
44 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Vertical Economizer
Solution offers a Vertical Economizer arrangement which consists of tiered segments; top and bottom. Both top and
bottom segments are designed to be of minimum length required. The VE arrangement is designed to be first in the
air-stream unless it is immediately preceded by XA, FR (DWDI), FR (SWSI), FE (DWDI), FE (SWSI).
The VE segment must be configured in a top tier arrangement per the following rules:
1. Only one VE per unit
2. Must be tiered over the MB or FM segment
3. MB or FM segment must have a top damper
General Considerations:
1. VE segment shall be available for all Solution unit 3. Both top and bottom sections of the VE segment
sizes provided engineering rules for stacking allow shall be designed to be of minimum length required.
the top section of VE segment to be tiered. The design shall allow the two sections of VE seg-
ment to be of different lengths.
2. VE segment shall be designed for the configurations
described in the sketches below. 4. Sound data shall be provided for all configurations
of VE segment.
5. Controls shall be available on VE segment for both
top and bottom sections.
6. Filter option shall be available in the bottom section
of the VE segment similar to FM segment.
7. Doors are available as an option for indoor units
and are required for outdoor units.
Notes & Options
• VE segment will have the same construction materials as the • Auxiliary drain pans optional except when bottom opening is
MB or FM segment. selected
• No optional auxiliary drain pain. • Variable size openings and dampers are optional.
• Optional Access Doors & View-ports. • Safety grate option for bottom openings
JOHNSON CONTROLS 45
FORM 102.20-QG1 (808)
MIXING BOX OPTIMIZATION CHART
This Mixing Box Optimization chart provides techniques and suggestions to meet the desired needs for your spe-
cific mixing box design process. It is a decision-making process in which the effectiveness of a mixing box must be
considered. Ideally, mixing boxes should provide adequate mixing.
Mixing Box Mixing Advantages Disadvantages

Assessment Effectiveness
Standard Mixing GOOD APPLICATION • Lowest first cost • Risk of low mixing effective-
Box Most effective • Space saving ness
with/without 1. In constant volume system • with filter
Angle Filter • Parallel blade control damper • with VAV
• Blade orientation and rotation • Risk of nuisance low limit
promotes mixing tripping
• Risk of stratification
Standard Mixing BETTER APPLICATION • Lower first cost • Risk of nuisance low limit
Box without filters Most effective • Mixes outside and return air tripping
and more proportionately • Risk of possible stratifica-
1 In VAV system
*Sequenced tion
2. With Min Max damper • Improves system perfor-
Controlled
mance at low flow rates
Dampers 3. With opposed blade control
damper • Sequence will add stability
(sequence listed
to the control loop
below) * Sequenced damper control is most
suitable for low air flow – low veloc-
ity applications
Standard Mixing BEST APPLICATION • Greatly improves mixing of • Higher first cost among
Box Most effective sub-freezing air streams damper designs
without filters and • Greatly reduces, if not elimi- • Increases unit length
1. Outside air designs at freezing
Static and sub-freezing temperatures nates, stratification in short • Some additional static
Air Mixer (blender) distances pressure loss
2.Constant or VAV systems
• Works effectively and con-
*Sequenced opposed control
sistently
dampers are recommended for
VAV systems
*Suggested sequence of operation as follows:
1) Start the fan with the return air damper fully open and the outdoor air damper fully closed.
a) An independent signal shall be sent to the Outdoor air damper
i) Minimum open position
b) An independent signal shall be sent to the Return air damper
i) Full open position
2) The outdoor air damper shall modulate further open to admit additional outdoor air as required to satisfy the (mixed air), (discharge air)
temperature sensor or IAQ requirements.
3) Once the outdoor air damper is fully open, if additional outdoor air is required, the return air damper shall modulate toward its closed
position.
46 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Typical Economizer Application Building Pressurization

ASHRAE Standards Demanding Economizer Consid- Building Pressurization – is defined as the relative air
erations: pressure in a building, as compared to the exterior or am-
bient air pressure. A design amount of outside air must
ASHRAE 90 - The ‘standard’ details requirements for
be introduced to insure design building ventilation.
a high performance & energy-efficient design of build-
ings (which includes equipment as part of the building This difference in pressure has a large impact on how the
system). building operates and it can have undesirable if not pe-
culiar impacts on building operations. Over-pressurized
What is high performance?
buildings will have doorways which are transformed into
• Lower energy usage wind tunnels. Under-pressurization will create a building
that has become negatively pressurized and infiltration
• Lower life cycle cost
makes indoor climate control difficult.
• Durable
The difference between the amount of OA and EA must
• Healthy remain constant at all operating conditions to maintain
proper building ventilation and pressurization.
• Productive
Over Pressurization caused by -
How buildings use energy?
• Too much OA
• Different building types use it differently
• Not enough EA
• Occupancy & equipment schedule
Results in -
• Internal vs. external load dominated buildings
• Excessive energy consumption
• Building occupants
• Perimeter doors opening
ASHRAE 62 - The ‘standard’ details Indoor Air Quality
issues with the purpose to establish acceptable ventila- Under Pressurization caused by -
tion procedures & standard-of care.
• Too little OA
What are ventilation procedures?
• Too much EA
• Mechanical ventilation systems shall include con-
Results in -
trols, manual or automatic, that enable the fan
system to operate whenever the spaces served are • Ventilation problems with occupants
occupied
• Excessive building odors
• The system shall be designed to maintain the
• Poor temperature control (infiltration)
minimum outdoor airflow as required under any load
condition • Excessive energy costs
What is a standard-of-care? • Difficulty in opening doors
• Guidelines to designers addressing contaminant Knowing how to correct and avoid pressurization prob-
source control, minimum maintenance activity & lems can prevent minor, inconvenient and comfort re-
frequency, filtration and managing relative humidity lated issues from growing into insurmountable problems
and liability issues.
JOHNSON CONTROLS 47
FORM 102.20-QG1 (808)
Methods of Pressurization Control Dedicated Exhaust Fan Economizer -

Full Return Air Fan Economizer - Fan runs only when economizer opens the OA dampers
Handles pressure losses through Handles pressure losses through
• Return air system • Return air system when in exhaust mode
• Exhaust dampers • Exhaust air path
Supply Fan handles pressure losses through Building pressurization provides insight in identifying,
diagnosing, correcting and most importantly, avoiding
• Outside air dampers
some unusual building operational problems.
• Mixed air dampers
Economizer Arrangements
TOP ANGLED
VIEW MIXING
DAMPER
( 100% OA, 100% EA) ( 100% OA, 100% EA)

(100% OA, 100% EA)
SIDE L/R SIDE

DAMPER
VIEW
EE - Economizer with EE - Economizer with vertical EF - Filter/Economizer

angled mixing damper. mixing damper. NOTE: Top damp-
ers not available for outdoor units.
LD08032 LD08033 LD08034
TOP
VIEW
SIDE
VIEW
SIDE
VIEW
EE - Inlet/Economizer VE - Vertical Economizer

(50% OA on each side with barometric exhaust) NOTE: VF (VerticalFilter Economizer) is available with filtration.
LD08035
Literature Reference — See Application Guide ‘Return & Exhaust Fan Economizers and Building Pressuriza-
tion’ – Form 100.00-AG3
48 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Face Damper – (FD)
FS XA FD XA
Notes & Options
The FD segment contains a full face damper Access doors and viewing ports must be located in adjacent seg-
• Face dampers are sized to cover whole components down- ments.
stream within tunnel. • Access is required immediately upstream of the FD segment
The FD is available for both indoor and outdoor applications. to access damper actuator and linkage.
• The FD can be located first in air stream or last in air stream, Damper material option:
only with indoor applications. • Galvanized
• Aluminum
Inlet Plenum – (IP) W
The Inlet Plenum is as its name implies; a segment

TOP/BOTTOM
used to provide a proper means of air entry into the air INTAKE
handler.
FRONT INTAKE
Openings may be applied to top, bottom, front, left side L
and right side. TOP VIEW

L
The variable size opening option allows the opening to FRONT VIEW
be properly aligned and sized for airflow convergence

and or divergence.
LEFT / RIGHT
SIDE INTAKE
H
SIDE VIEW
Notes & Options
If a plenum fan is used as a return fan and return air is ducted, an IP • Access Door - Optional
segment must be provided upstream of the plenum fan. • Auxiliary Drain Pans – Optional
• Dampers are not available as an option
JOHNSON CONTROLS 49
FORM 102.20-QG1 (808)
ACCESSORY SEGMENTS
Diffuser Segment – (DI)

The diffuser segment is constructed of heavy gauge
galvanized steel with a built-in perforated plate, which
prevents high velocities through the center of the down-
stream component. This segment is mainly used for
blow-thru type applications immediately after a DWDI
fan or locations where even air distribution across the
unit cross section is a necessity.
Notes & Options
The Diffuser Segment must be placed immediately downstream of • Auxiliary Drain Pan - Optional
a DWDI fan segment when filters, attenuators, humidifiers, electric • Access Door – Optional
heater and/or coils immediately follow the fan.
Access Segment – (XA)

The Access Segment is a functional segment provided
to allow access-to or inspection-of any component in
adjacent segments. The access segment assists in de-
termining the best segment arrangement for a specific
function and or layout.
It is designed for flexibility with full sized access doors
and variable segment length. XA
Notes & Options
Access Segments may be used at any point in the unit configura- • Auxiliary Drain Pan - Optional (minimum segment length ap-
tion; positive pressure (blow thru) or negative pressure (draw thru) plies)
configurations. • Access Door – Optional (both sides of the unit -minimum seg-
Access segments may be provided for maintenance, cleaning, service ment length applies)
and or spacing for correct air flow requirements.
50 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Vertical Plenum – (VP) VP
The Vertical Plenum (VP) is a segment designed for

vertical configurations (top tier) with unique discharge
arrangements.
Multiple and variable size supply air openings are avail-
able through the VP segment.
The VP segment may be applied as an acoustical
chamber, with perforated panel option, that dampens
low frequency sound. In addition, the air stream expan-
sion reduces turbulence and creates an acoustical end
reflection.
FS XA AF
Notes & Options
Discharge locations available are top, front, rear, left side and right Discharge opening options are rectangular, round and oval.
side. Doors are optional (Inward opening for positive pressure)
Discharge Plenum – (DP)

The Discharge Plenum (DP) is a segment designed
for horizontal configurations with unique discharge ar-
rangements.
Multiple and variable size supply air openings are avail-
able through the DP segment.
The DP segment may be applied as an acoustical
chamber, with perforated panel option, that dampens
low frequency sound. In addition, the air stream expan-
sion reduces turbulence and creates an acoustical end DP FS XA AF
reflection.
Notes & Options
Discharge locations available are top, bottom, rear, left side and Discharge opening options are rectangular, round and oval.
right side. • Auxiliary Drain Pan - Optional
• Access Door – Optional (both sides of the unit - Inward open-
ing for positive pressure)
JOHNSON CONTROLS 51
FORM 102.20-QG1 (808)
ACCESSORY SEGMENTS
Sound Attenuator – (AT) SOUND

ATTENUATOR
Sound Attenuators are rated for two flow conditions,

FORWARD and REVERSE.
• Forward flow occurs when air and sound-waves
travel in the same direction, as in a supply air duct
or fan discharge.
• Reverse flow occurs when sound-waves and
air travel in opposing directions, as in a typical
return-air system.
Because attenuation values are generally higher in
the first five octave bands in the reverse flow mode,
compared to the forward flow mode, more economical
silencer selections can often be made on the return-air
systems. These phenomena are illustrated below.
RACEWAY ASSEMBLY
BULKHEAD ASSEMBLY
FORWARD FLOW REVERSE FLOW
Under FORWARD FLOW conditions, high- Under REVERSE FLOW conditions, sound is
frequency sound is refracted into the duct- refracted away from the walls and toward the
silencer walls. center of the duct-silencer.
Notes & Options
Silencer Length Options: Frequency Range

• 3ft, 5ft, 7ft • Normal
Face Velocity • Low
• Low Casing Materials:
• Ultra Low • Galvanized
Media Types: • Stainless Steel
• Standard Access doors and viewing ports must be located in adjacent segments.
• Film-lined (Hospital media) When AT segment is located immediate downstream of DWDI fan
• None (No media) segment a Diffuser segment is needed to ensure even airflow dis-
tribution.
Literature Reference — See Application Guide ‘Acoustichecks for Air Handling Projects’ – Form 100.00-AG2 &
‘Fundamentals of Acoustics’ – Form 102.20-AG4
52 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Noise & Vibration

Any mechanical device is capable of generating noise
and vibration for a variety of reasons. The air handler
unit noise emanates simultaneously from three distinct
sources: aerodynamic, mechanical, and electrical.
Noise generally applies to any problem in which the ears
are the main sensor. Noise is made up of many different
sound frequencies at various loudness levels. Noise
when compared to vibration is similar in that they both
have amplitude and frequency. Usually noise is a much
lower amplitude and energy content which is measured
in db referenced to Watts. Typically noise has a much
wider frequency range and a higher upper limit than
vibration (63Hz – 8KHz)
Vibration generally applies to any problem in which
the hands or touching are the main sensor. Amplitude
is large when there is a problem. It has much greater
energy content with a smaller frequency range (3Hz
– 500Hz) To avoid unsatisfactory noise levels, many factors should
be considered at the design stage. Noise is generally
considered low quality, unwanted sound. Characteristic
Noise Considerations and Characteristics
words such as tone, pitch, steady, unsteady and inter-
Mechanical and electrical noise sources usually begin mittent help to define whether the source of the noise
as vibration and are later transferred into airborne noise. is aerodynamic, mechanical or electrical.
Aerodynamic Mechanical Electrical

Generated noise is caused by turbu- Generated noise has a different sound Generated noise is a function of motors,
lence, high velocities, and instabilities quality and characteristic. It can have relays, motor controls, or unbalanced
due to pulsation and surge. Technically a metallic sound caused by metal-to- line voltages into the motor
speaking it relates to pressure pulsa- metal contact or working noise radiating
tions and is characterized by a continu- from belts and bearings. This noise may
ous broadband frequency spectrum be constant or intermittent.
with an objectionable superimposed
pure tone.
Vibration Considerations and Characteristics amount of unbalance of the rotating components. The
frequency at which this occurs is the operating RPM of
Rotating devices, such as air handling units, all create
the components. There are many different sources of
vibration which can be transmitted to other parts of the
vibration. One of the most difficult tasks is the systematic
structure. The magnitude of this vibration is subject to
identification of the vibration characteristic; amplitude,
a number of things, the most significant of which is the
frequency, location or direction.
Aerodynamic Mechanical Electrical

Vibration is generated when a forced Vibration may occur from unbalance, Vibration generated occurs from torsion
vibration in which the energy and char- resonance, looseness and rubbing. fluctuations, eddy current induced fields
acteristics of the air-stream are large and improper wiring.
enough to cause turbulence, pulsations
or a blade frequency tone. Vibration can
also be the result of a resonance (rever-
beration).
JOHNSON CONTROLS 53
FORM 102.20-QG1 (808)
ACCESSORY SEGMENTS
Air Blender/Mixers – (AB) placed just after the mixing segment improves mixing
outside and return air streams. Mixers work effectively
The static mixer provides a high level of mixing in a
and consistently. There are no moving parts.
minimal distance and at a low pressure drop. Mixers
Applications (When used): Features & Benefits:

– Eliminates air stratification – Provides most mixing in shortest possible dis-
tance
– Reduces low limit-stat nuisance trips
– Requires negligible energy (typical application is
– Improves accuracy of temperature control sys-
between 0.10 - 0.20” w.g.)
tems
– Provides expected mixing for every cabinet size
– Mixes outside ventilation air into supply air stream
to satisfy IAQ/IEQ requirements – Provides reliable pressure drop rating which
includes the effect of mixer to plenum area ratio.
– Allows for greater use of economizer operation
– Provides uniform velocity profile for even filter
loading and enhanced coil performance
Notes & Options
AB segment should be applied immediately after the mixing box/econo- Air mixer arrangements may include one mixer, two horizontal mixers,
mizer segment. AB segment is designed to mix air from openings on three horizontal mixers, two vertical mixers or three vertical mixers.
any combinations of: top, bottom, end and sides. The arrangement depends upon upstream segment configuration.
Minimum velocity through a mixer is 400 FPM. Door - optional
Drain pan - optional
Mixer material option: Aluminum or Stainless Steel
54 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Face & Bypass Damper Segments – (IB), (EB)
Internal Face & Bypass – (TB)

The IB Segment must be located immediately upstream
of a reduced face coil.
FS HC IB XA AF
• Available for indoor or outdoor applications.

• Designed to divert airflow around a coil.
When a full face coil is required downstream of the re-
duced face coil, access segment(s) must be included
between the coils.
IB segment is used to control
• Humidity
• Low temperature flows across water coils
Notes & Options
Access doors and viewing ports must be located in adjacent seg- Damper material option:
ments. • Galvanized
• An 18” access door is required immediately upstream of the IB • Aluminum
segment to access damper actuator and linkage.
External Face & Bypass – (EB)
Each EB segment must be configured with a “bypass air

inlet” downstream in the configuration for reintroducing
the bypassed air to the unit. The EB segment cannot
exist without such a “bypass air inlet” partner.
• The EB segment is available for indoor
application only
The external face and bypass damper is located up-
stream of a full-face coil. External Bypass damper is
a balanced opposed blade face damper with intercon-
necting linkage.
• Bypass duct is to be field supplied
FS HC EB AF
Notes & Options
Damper material option: Door is optional

• Galvanized • It is designed to divert airflow through an external bypass duct.
• Aluminum • External Bypass segment assumes ‘top’ outlet.
Drain pan is optional
JOHNSON CONTROLS 55
FORM 102.20-QG1 (808)
ACCESSORY SEGMENTS
IP TN TN XA HF XA DP
Turning Segments – (TN)

The purpose of the Turning Segment is to assist air
turning in a vertical direction.
A Turning Segment (TN) can only be located at the end
of a unit configuration.
Segment lengths are engineered for a variety of tiered
space saving configurations.
FS CC AF TN TN FS CC AF MB
Notes & Options
TN segments are available for configuring in both top and bottom Access Door – Optional (both sides of the unit - Inward opening for
tiers. positive pressure)
Drain pan is optional for bottom tier segments.
Humidifier Segment – (HM)

Adding humidification for full winter comfort and produc-
tivity is just as important as air conditioning in the sum-
mer months. Temperature control must be combined with
humidity control to maintain proper comfort parameters.
ASHRAE 62 indicates that relative humidity is part of
acceptable ventilation procedures & standard-of care
Solution provides a standard steam injection distribution
type humidifier with a short absorption manifold for use
where short steam absorption distances are critical.
• Steam is distributed evenly through the full length
of the manifold.
• The header size, number and spacing of distribu-
tion tubes shall be determined so that all steam
is absorbed by the air before reaching the next
component in the air stream depth.
Notes & Options
• Electric, gas and steam-to-steam generator types • Valves cannot be selected as an off-the-shelf item; each valve
• Optional auxiliary drain pan has a specific plate/orifice specifically cut per order specifica-
tions.
• Optional access doors
• Control valve actuation shall be electronic and shall be
• Optional controls compatible with either a 0-10V DC signal or a 4-20 mA control
• The recommended location of the HM segment is downstream signal.
of the HC segment but upstream of the CC segment. • Factory mounted controls are not available in the Humidifier
• The humidifier segment can not be configured upstream of a segment. Any FMED device in a downstream segment should
HEPA filter segment. be located at least the absorption distance away from the
• The humidifier segment may be configured upstream of RF, humidifier manifold.
FF, and AF filter segments. • Usual humidifier headers are located the same side as coil
• Valve package shall be supplied and shipped loose. Field headers.
Installation and wiring is required. • Optional stainless steel supports and liner
• The Humidifier Vendor humidifier selection software shall size
the valve package.
56 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
UV Segment – (UV)
Johnson Controls has developed UV-C lighting options that control the growth and transfer of surface and airborne
microbial agents. By incorporating UV light options into your air handling unit it is now possible to control micro-
biological infestations, using ultraviolet light technology to disinfect the unit, thereby maintaining the cleanliness of
the unit and the re-circulated air of the space being conditioned. By eliminating a multitude of micro-organisms, IAQ
is improved and occupants are healthier.
Surface Decontamination Option – is done by Airborne Inactivation Option – is accomplished

incorporating UV-C lights in the coil segment down- by installing the stand-alone “Airborne Inactivation”
stream of all cooling coils and above all drain pans. segment upstream and/or downstream of all cooling
In this application reflectivity of the UV light is of coil segments to control airborne microbial agents.
dominant importance. Exposure time is unlimited. Any UV-C lights for this type of application are of higher
increase in reflectivity enhances the UV effectiveness intensity and are designed for “On-the-fly” kill of air-
and efficiency. The kill rate increases dramatically borne contaminates. Lamps are configured for 360°
with this application method. UV irradiance for maximum air-stream cleansing.
AIRBORNE OPTION SURFACE OPTION
Combining Both Options – If both Surface Decon-

UV UV
tamination and Airborne Inactivation options are used
SA
together, they can virtually clean your unit and the air OA
you breathe. Working together with various filtration sys-

tems and complying with the requirements of ASHRAE
Standard 62.1 will assure the best possible IAQ when
a designer combines all of these technologies.
DP HF XA DI FS CC AF MB
RA
Notes & Options
Optional Radiometer • Mechanical interlock switch to assure that the UVC assembly
• Radiometer detects and measures intensity of radiant thermal will be de-energized when accessed.
energy • Optional View-port
Optional Access Door Optional stainless steel supports and rails
• Access is optional for servicing the UV lights.
Literature Reference — See Application Guide — ‘Solution® Air-Handling Units UV-C Light Options’ – Form:
102.20-AG16 & Specification Sheet – Form: 102.20-S16
JOHNSON CONTROLS 57
FORM 102.20-QG1 (808)
ACCESSORY SEGMENTS
Pipe Chase Enclosure 3. Roof, floor, side and end panels will be double
wall construction.
1. The Pipe Chase may be selected in various
depths. 4. Pipe chase doors
2. The Pipe Chase may be applied to XA, HC, CC, • All pipe chases must have at least one door.
VC, IC or IG segment.
5. Pipe chase curb
a. These segments must be on the bottom tier of
• The pipe curb under a pipe chase will be level
an indoor or outdoor unit.
with the curb under the unit.
WALL PANEL WITH
COIL OUTLETS
PIPE CHASE
PANEL ASSEMBLY
PIPE CHASE
ACCESS DOOR
PIPE CHASE
CURB ASSY
OUTDOOR: DRAIN CONNECTION IS ALWAYS ON SIDE OPPOSITE PIPE CHASE.
INDOOR: DRAIN CONNECTION IS ALWAYS SAME SIDE AS PIPE CHASE.
Roof Curb
Johnson Controls recommends that an HVAC factory
curb always be provided. Solution curbs are built to fit
the unique footprint of each air handler. Solution also
provides specific drawing and specification data for each
unit and curb. These documents provide vital data such
as unit dimensions, weight, component details, cross
braces, supply & return opening layout dimensions, and
notes which are unique to each unit.
Although insulated curbs are specified in many cases,
the contractor responsible for the roof typically supplies
the insulation function.
Notes & Options
1. Johnson Controls does not recommend vibration isolation be 3. Dual vibration isolation applications must be designed by a
provided on both the fan skid, inside the unit, and the curb, licensed Professional Engineer specializing in vibration isola-
outside the unit, without credible testing results. tion design.
2. Using improperly designed internal and external isolation 4. Units with a baserail and a bottom opening: duct connection is
springs can increase vibration. flush with the bottom of the unit, not flush with the baserail.
58 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
SLOPED CURB
LENGTH-WISE SLOPE
OUTSIDE OUTSIDE
AIR AIR 42
RETURN RETURN
*14" SUPPLY 14" AIR SUPPLY
AIR 42"
AIR MIN AIR
MAX
ROOFTOP ROOFTOP
SUPPLY > RETURN RETURN > SUPPLY

CHASE
CHASE
PIPE
PIPE
WIDTH-WISE SLOPE 14"
42" RETURN 14" RETURN
MIN 42"
MAX AIR IN MIN AIR IN
MAX
ROOFTOP ROOFTOP
RIGHT > LEFT LEFT > RIGHT
Special Curb Requests
Spring isolation curbs Seimic isolation curbs

Roof curbs that incorporate adjustable spring isolators Roof Curbs that incorporate seismic isolation as a fully
into the curb as a single component. Most isolation curbs adjustable support system specifically designed for unit
are designed for 1” static deflection springs. The springs vibration and seismic/wind restraint. Seismic isolation
are mechanically fastened and sized within the frame curbs are designed to meet superimposed live and
to ensure uniform deflection for the entire system. The dead loads, including equipment and other construction
vibration eleimination portion of the curb is constructed loads to be supported by the curb. The curb contains
of structural steel and should be designed to match the mountings designed and rated to resist seismic forces
bottom of the rooftop unit. Usual operating height is 21” in all directions.
with options for different heights.
Literature Reference — See Application Guide — ‘Roof Curb & Unit Application’ – Form 100.00-AG11
JOHNSON CONTROLS 59
FORM 102.20-QG1 (808)
CONTROLS
Factory-Packaged Controls – (FPC) Typical FPC Wiring

YORK Factory-Packaged Controls assure you of get- Location of wiring harnesses are typically opposite the
ting: high voltage. See “Power-Wiring Options diagram on
• A complete factory-engineered system page 62.
• Reduce costs by taking the guesswork out of

control installation
• A higher quality control system direct from the fac-
tory
• Full service support
Notes & Options
Factory mounted devices are available as packaged ‘Standards’ kits, Devices are available in a variety of options from mount-only with no
which are defined as pre-engineered system applications. Most likely control panel to a complete mounted, wired and factory-tested with
several ‘Standards’ will “fit” a given AHU configuration. the Johnson Controls Metasys FEC series controller.
60 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
Software Process
The software process will automatically apply the devices to the functional segments required for the control
method.
Field Equipment Controller (FEC)

Our open design FEC conrollers use the industry stan-
dard BACnet MS/TP open communication protocol
– customers can use devices from other vendors on
the network, don’t have to stay with one vendor which
provides wider options to the customer and consulting
engineer
On time, on budget – Standards reduce engineering
and installation time and result in the lowest possible
installed cost. New tools like CCT reduce configuration
and commissioning time.
Minimize issues – Johnson Controls builds reliability into
each device. Our documentation and training are excel-
lent so the devices are installed correctly the first time.
Reduce operating costs – With adaptive tuning, the sys-
tem uses process condition information it acquires and
adapts for improved control without manual intervention.
State-based control reduces wear and tear on actuators
and other components by allowing the system to be in
only one mode at a time. For example, only heating or
only cooling.
JOHNSON CONTROLS 61
FORM 102.20-QG1 (808)
CONTROLS
Power Wiring Options
TOP VIEW
LOW VOLTAGE
SUPPLY FAN MOTOR WIRING. RETURN FAN MOTOR WIRING.
CDW - COOLING
CDW - HEATING
LOW VOLTAGE
EMAL
HIGH VOLTAGE
SUPPLY FAN MCC CABINET.
OPTIONAL SINGLE POINT
MOTOR WIRING ALTERNATE MOTOR WIRING CUTOUT LOCATION
FAN SEGMENT PRIMARY ACCESS DOOR.
RETURN FAN MCC CABINET.
Notes & Options
All motor wiring will be sized and installed based upon National A disconnect panel will be required anytime there are (2) or (3)
Electrical Code requirements. The wire-ways will be categorized as 3-phase loads that require a common factory terminated wiring con-
follows: nection. A maximum of (3) 3-phase loads are allowed for single point
• High Voltage – (120V and higher) is usually on drive side of the power option.
product 3-phase loads are as follows:
• Low Voltage – (24V) is usually on opposite drive side. i. Supply Fan Motor Controller
• All motor wiring will be installed neatly in perpendicular and/or ii. Return / Exhaust Fan Motor Controller.
parallel planes with the unit walls and floors. iii. Gas Heater.
Single Point Power (SPP) is defined as: iv. Electric Heater.
1. ALL electrical loads in a specific unit configuration wired to a v. Energy Wheel Motor Controller.
common point of connection through the proper motor control
protection devices. This requires the customer to bring only one
source of power to the unit.
2. Where motor controls (VFD, starter or wired disconnect) are NOT
selected, no motor wiring shall be provided. Should 120V or 24V
elements be selected where motor controls are not included, they
shall require field wiring.
3. Where multiple motor control devices are selected, optionally,
single point power connections shall be provided. The field power
supply point shall be the supply fan segment.
4. Where an external wired disconnect option is selected for either
supply or return/exhaust fans (or both), single point wiring shall
NOT be available.
There are three different sizes of transformers available; 150VA,
500VA, and 2000VA.
• The transformer being the device, used to transform power
from a primary voltage of 460 volts, 230 volts, or 575 volts, to
a secondary voltage level. An example of a secondary voltage
would be 120 volts.
62 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
INDUSTRY FORMULAS
Electrical
Watts ÷ Amps = Volts Amp (A) = a measurement of rate of flow of electrons along
Volts x Amps = Watts a wire
Watts ÷ Volt = Amps
Volt (V) = a measure of electrical potential Kilowatt (kw) = a thousand watts
Watt (W) = a measure of power an electrical device BTU = KW x 3415
consumes 1KW = 1.34 HP
1 HP = 2545 BTUH
PUMP KW = FLOW (gpm) x PD (ft) PUMP HP = FLOW (gpm) x HEAD (ft

5311 x E pump x E motor 5311 x E pump x E motor
FAN KW = .7457 x BHP FAN HP = CFM x SP

E motor 6350 x E fan
1.73 = √3 FOR THREE PHASE SERVICE FAN STATIC EFF = CFM x SP

6350 x BHP
FAN MECH EFF = CFM x TP

6350 x BHP
Basic Fan Laws Drive Calculations
CFM varies directly as the RPM Motor RPM x Motor Pulley PD = Blower RPM x Blower
CFM1 = RPM1 Pulley PD
CFM2 RPM2
Static pressure varies as the square of the RPM Example:
SP1 = (RPM1)2 = (CFM1)2 1,750 x 7.2 = 1,190 Blower RPM
SP2 (RPM2)2 (CFM2)2 10.6
HP varies as the cube of the RPM 10% too much CFM:
BHP1 = (RPM1)3 = (CFM1)3
BHP2 (RPM2)3 (CFM2)3 1,750 x 7.2 = 11.8 “ PD Blower Pulley
1,190 x (0.90)
Air
TOTAL COOLING LOAD (MBH) = 4.5 x CFM STANDARD AIR x (ENTHALPY ENT. AIR - ENTHALPY LVG. AIR) / 1000
4.5 = 0.075 (WT. OF STD. AIR, # / FT3) x 60 (MIN./HR.)
SENSIBLE COOLING LOAD (MBH) = CFM x 1.08 x (EDB-LDB)
1000
1.08 = 0.075 (WT. OF STD. AIR, # / FT3) x 60 (MIN./HR.) x .24 (Specific Heat of dry air)
SENSIBLE HEAT RATIO = SH

MBH/Sq. Ft. x FA x 1000
TOTAL COOLING LOAD (BTW/HR) = GPM x 500 x (EWT-LWT)

500 = 8.33 (WT. OF H20 @ 60 deg F, # / GAL) x 60 (MIN./HR.) x 1.0 (Specific heat of water)
Metric Conversions
CFM x 1.6992 = m3/hr Ft/min x 0.00508 = m/s BTU x 0.00029 = kWh
CFM x 0.4719 = L/s Inch x 25.4 = mm Gpm x 0.063 = L/s
HP x 0.7457 = kW Lb x 0.4535 = kg
JOHNSON CONTROLS 63
FORM 102.20-QG1 (808)
GUIDE SPECIFICATIONS
PART 1 GENERAL
1.01 SECTION INCLUDES

A. Indoor and outdoor air handling units and components as scheduled and shown
on drawings.
B. Motor disconnects, motor starters, and variable frequency drives.
1.02 RELATED SECTIONS

A. The requirements of the General Conditions, Supplementary Conditions, Divi-
sion 1, equipment schedules, and drawings apply.
1.03 REFERENCES
A. AMCA 99 – Standard Handbook
B. AMCA 210 – Laboratory Methods of Testing Fans for Rating Purposes
C. AMCA 500 – Test Methods for Louvers, Dampers, and Shutters
D. AMCA 611-95 – Methods of Testing Airflow Measurement Stations for Rating
E. ANSI/AFBMA 9 – Load Ratings and Fatigue Life for Ball Bearings
F. ANSI/UL 900 – Test Performance of Air Filter Units
G. ARI 260 – Sound Rating of Ducted Air Moving and Conditioning Equipment
H. ARI 410 – Forced-Circulation Air Cooling and Air Heating Coils
I. ARI 430 – Testing and Rating of Central-Station Air Handling Units
J. ASHRAE 52.1/52.2 – Method of Testing General Ventilation Air Cleaning
Devices for Removal Efficiency by Particle Size
K. ASHRAE 62 – Ventilation for Acceptable Indoor Air Quality
L. ASHRAE 90.1 – Energy Standard for Buildings Except Low-Rise Residential
Buildings
M. ASTM-C 1338 – Standard Test Method for Determining Fungi Resistance of
Insulation Material and Facings.
N. NFPA 70 – National Electric Code (conductors, equipment and raceways)
O. NFPA 90A – Installation of Air Conditioning and Ventilation Systems
P. SMACNA – HVAC Duct Construction Standards
Q. UL-181 – Mold Growth and Humidity Test
R. UL-1995 – Standard for Safety for Heating and Cooling Equipment
S. ISO/PWD 13261-3 – Sound Power Rating of air-conditioning and air-source
heat pump equipment: Part 3, Ducted Equipment.
T. ISO 9614 – Determination of sound power levels of noise sources using sound
intensity: Part 1, Measurement at discrete points; Part 2, Measurement by scan-
ning, and Part 3, Precision method for measurement by scanning.
1.04 QUALITY ASSURANCE

A. Manufacturer shall have a minimum of 25 years of experience in designing,
manufacturing, and servicing air-handling units.
64 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
B. The design indicated on the schedules and shown on the drawings is based upon
the products of the named manufacturer. Alternate equipment manufacturers
are acceptable if equipment meets scheduled performance requirements and
dimensional requirements.
C. If equipment is supplied by a manufacturer other than the one named, coordinate
with the General Contractor and affected subcontractors to ensure the specified
performance is met. This coordination shall include (but is not limited to) the
following:
1. Structural supports for units
2. Size and location of concrete bases/housekeeping pads
3. Location of roof curbs, unit supports and roof penetrations
4. Ductwork sizes and connection locations
5. Piping size and connection/header locations
6. Interference with existing or planned ductwork, piping and wiring
7. Electrical power requirements and wire/conduit and over current protection
sizes.
8. Trap height requirements
D. The Mechanical Contractor shall be responsible for costs incurred by the General
Contractor, Subcontractors, and Consulting Engineers to accommodate units fur-
nished by a manufacturer other than manufacturer named as basis of design.
1.05 RATINGS AND CERTIFICATIONS

A. Air Handling Unit safety: ETL or UL 1995
B. Air Handling Unit energy use: ASHRAE 90.1
C. Fans: AMCA 210
D. Air Coils: ARI 410
E. Air Handling Unit certification program: ARI 430
F. Filter media: ANSI/UL 900 listed Class I or Class II
G. Control wiring: NEC codes & ETL requirements
H. Motors: Federally mandated Energy Policy Act (EPACT).
I. Airflow Monitoring Stations: AMCA 611-95
1.06 SUBMITTAL DOCUMENTATION REQUIRED

A. Furnish fan performance ratings and fan curves with specified operating point
clearly plotted.
B. Furnish drawings indicating unit dimensions, required clearances, field connec-
tion locations, wiring diagrams, shipping drawings, and curb drawings.
C. Furnish performance report showing fan, motor, coil, and component performance
details. Performance report shall detail unit casing performance and include
materials, gauges, and finishes.
D. Furnish operation and maintenance data, including instructions for lubrication,
filter replacement, motor and drive replacement, and condensate pan cleaning;
spare parts lists, and wiring diagrams.
JOHNSON CONTROLS 65
FORM 102.20-QG1 (808)
[Tip 1]: ARI 430 established testing,

E. Adjust and report performance ratings for the proper altitude of operation. rating and conformance requirements for
AHUs. To claim compliance, manufacturers
F. Report air-handling unit performance ratings in accordance with ARI-430 must periodically submit production AHUs
to ARI for testing.
(static pressure, airflow, fan speed, and fan brake horsepower).
G. Report static pressure profiles by component section.
H. Report coil ratings in accordance with ARI-410 (capacities and pressure rating and reporting standards for air coils.
This includes special attention to heating
drops). and cooling capacity as well as air and fluid
pressure drops.
I. Report and rate sound power levels in accordance with ARI-260 (ducted dis-
charge, ducted inlet, free inlet sound).
[Tip 3]: ARI 260 standardized the
J. Airflow measuring device performance shall be certified and rated in accordance measurement and reporting of sound data
with AMCA-611. Report data in accordance with AMCA-611. Provide AMCA for AHUs. It does not require manufacturers
Certified Rating Seal for Airflow Measurement Performance. to adhere to a certification program to claim
compliance. It does require an extensive
K. Report panel deflection at +/-8” w.g., stated in terms of ‘L/X’ where ‘L’ is the testing program. (Note: AMCA 300 applies
to sound for bare fans only)
casing panel length and ‘X’ is a constant provided by the AHU manufacturer.
L. Report casing leakage rate at +/-8” w.g., specified in terms of percentage of [Tip 4]: AMCA 611 details the require-
design airflow. ments for certifying the performance of
airflow measuring stations. It assures buy-
M. Report weight loads and distributions by component section. ers that the reported data is accurate and
reliable. Testing is performed by AMCA or
N. Report product data for filter media, filter performance data, filter assembly, and by an independent AMCA certified facility.
filter frames.
O. Report electrical requirements for power supply wiring including wiring dia-
grams for interlock and control wiring, clearly indicating factory-installed and
field-installed wiring.
P. Report motor electrical characteristics.
1.07 DELIVERY, STORAGE AND HANDLING

A. Comply with ASHRAE 62, Section 5 (mold and corrosion resistant casings,
filters upstream of wetted surfaces, and drain pan design).
[Tip 5]: ASHRAE 62 established
B. Comply with ASHRAE 62, Section 7 (practices to be followed during construc- minimum standards for designing, building
tion and startup). Protect equipment from moisture by appropriate in-transit and and operating a building to help ensure ac-
on-site procedures. ceptable indoor air quality.
C. Follow manufacturer’s recommendations for handling, unloading and storage.

D. Protect, pack, and secure loose-shipped items within the air-handling units.
Include detailed packing list of loose-shipped items, including illustrations and
instructions for application.
E. Protect, pack and secure controls devices, motor control devices and other elec-
tronic equipment. Do not store electronic equipment in wet or damp areas even
when they are sealed and secured.
F. Enclose and protect control panels, electronic or pneumatic devices, and variable
frequency drives; and pack with desiccant bags. Replace desiccant bags every 60
days. For equipment stored in an environment with a relative humidity greater
than 60%, change bags every 30 days. Do not store equipment in wet or damp
areas even when they are sealed and secured.
G. Seal openings to protect against damage during shipping, handling and stor-
age.
66 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
H. Provide shrink-wrap around unpainted units. The membrane shall cover entire
AHU during shipping and storage. Cover equipment, regardless or size or shape.
Tarping is not acceptable.
I. Shrink-wrap equipment, including electrical components, for protection against [Tip 6]: ASHRAE 62 Section 7.1.3
rain, snow, wind, dirt, sun fading, road salt/chemicals, rust and corrosion. Keep recommends the protection of equipment
equipment clean and dry. on site and during transport. Shrink wrap is
a cost-effective, high-quality way to comply
J. Tarp painted units to protect against rain and road debris during shipping. with this recommendation.
K. Clearly mark AHU sections with unit tag number, segment sequence number,
and direction of airflow. Securely affix safety-warning labels.
1.08 EXTRA MATERIALS

A. Provide one set of filters for balancing, and one additional set for final turnover
to owner.
B. Provide one extra set of belts, in addition to the factory-installed set.
1.09 WARRANTY
[Tip 7]: Specifying an 18 month
A. Provide warranty for 18 months from date of shipment. Warranty shall cover warranty helps to ensure that the owner will
benefit from a full 12 months of warranty.
manufacturer defects. Warranty shall include labor for 12 months from date of Specifying labor warranty ensures that the
shipment. Warranty work shall be performed by manufacturer’s factory-trained manufacturer will stand by their product
and factory-employed technician. Service technician must be based within 50 for quality and performance during that
time. Specifying local service support helps
miles of job site. ensure quick response when service is
desired or needed.
B. Include factory-provided controls in the parts and labor warranties.
C. Parts associated with routine maintenance, such as belts and air filters shall be
excluded.
1.10 SYSTEM STARTUP

A. Do not operate units for any purpose, temporary or permanent, until ductwork
is clean, filters are in place, bearings lubricated, and fan has been test run under
observation.
B. Comply with manufacturer’s start-up requirements to ensure safe and correct
operation and integrity of warranty.
PART 2 PRODUCTS
2.01 ACCEPTABLE MANUFACTURERS

A. YORK Solution
B. Approved Equal (Prior written approval by engineer of record is required)
2.02 GENERAL DESCRIPTION

A. Air Handling Unit (AHU) consists of a structural base, insulated casing, access
doors, fans, motors, motor controls, coils, filters, dampers, controls, components,
and accessories; as shown on drawings, schedules, and specifications.
B. Provide AHU to meet the specified levels of performance for scheduled items
including airflow, static pressure, cooling capacity, heating capacity, electrical
characteristics, sound, casing leakage, panel deflection and casing thermal per-
formance.
JOHNSON CONTROLS 67
FORM 102.20-QG1 (808)
C. AHU shall maintain structural integrity when wall panels are removed.
D. Provide internal components and accessories as specified and scheduled. Com-
ponents and accessories shall be installed by the AHU manufacturer in an ISO-
9002 certified facility.
E. Ship units in one piece. Split units only where necessary for shipping and instal-
lation.
F. Manufacturer shall provide detailed, step-by-step instructions for disassembly
and reassembly.
G. For AHU segments that must be broken down for rigging and installation: seg-
ment shall be disassembled and reassembled by manufacturer’s factory-trained
service personnel.
H. Manufacturer shall perform a field leakage test to confirm 1% leakage per section
2.25.
I. Manufacturer shall provide a written statement confirming that the unit is built
to the manufacturer’s factory standards and that the unit will carry the full war-
ranty.
2.03 STANDARDS COMPLIANCE

A. Comply with ratings and certifications referenced in this specification.
B. Manufacturers who do not comply with ARI-430 shall factory test EACH unit rating and conformance requirements for
to verify brake horsepower rating, airflow performance and total static pressure AHUs. To claim compliance, manufacturers
performance. See specification Section 2.23 (VERIFICATION OF PERFOR- must periodically submit production AHUs
to ARI for testing.
MANCE) for testing requirements.
C. Manufacturers who do not conform to requirements of ARI 260 for ducted dis-
charge and return air sound shall submit EACH unit to an independent sound
test laboratory for ARI 260 testing. The test laboratory shall conform to ARI
260, Section 4.4, Test Equipment and Facilities.
2.04 BASE RAIL

A. Provide a structural base rail under the full perimeter of the unit, formed from
mill galvanized steel.
B. Provide clearance for proper external trapping of drain pans steam conden-
sate.
C. Provide base rail and lifting lug system that does not require additional support
for rigging. Include base rail lifting lugs at each side shipping splits and at unit
corners.
2.05 CASING
A. Provide double wall AHU casing. Exposed insulation is not acceptable.
B. Panel assembly shall meet UL standard 1995 for fire safety. Panel assembly
shall comply with the requirements of NFPA 90A.
C. Provide an insulation system that is resistant to mold growth in accordance with [Tip 9]: This spec item also found in
ASHRAE standard 62, section 5.5.1.
a standardized test method such as UL 181 or ASTM C 1338.
D. Encapsulate insulation with sheet metal so that air does not contact insulation.
Panels insulated with fiberglass shall be sealed at each corner and around their
entire perimeter, to eliminate airflow through the panel and to eliminate microbial
growth potential within the casing wall.
68 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
[Tip 10]: Casing thermal performance

E. Provide casing with minimum thermal resistance (R-value) of 12 hr-ft2-°F/ has a direct impact on the owner’s utility bill.
BTU. Spec R-12 for the utmost in energy savings.
Many manufacturers employ 2” walls with
F. Roof, wall, floor, and access door panels shall be galvanized or stainless foam insulation to achieve this high thermal
performance. With fiberglass insulation, 4”
steel. walls may be required to achieve R-12.
G. Provide an additional .125” aluminum diamond tread plate floor liner in access
[Tip 11]: Some manufacturers do not
areas. insulate the frames of their units, leaving
the casing vulnerable to sweating and
H. Provide perforated liner in the fan section and other sections as shown on the energy loss.
drawings. The perforated panel shall enclose matte-faced fiberglass insulation.
[Tip 12]: Some manufacturer’s cas-
I. Provide a unit frame of galvanized steel that provides the overall structure of ings leak 5% or more. Ensure that energy
the unit and does not rely on the casing panels for structural integrity. Insulate is not wasted by outward leakage and that
frame in the same manner as panels, roof, and floors. conditioned air is not contaminated by
inward leakage. Leaky units are also prone
J. Provide AHU casing that leaks no more than 1% of design airflow at +/-8” to sweating at their leak points. 1% leakage
at design static pressure is a very common
w.g. benchmark for leak integrity.
K. Provide wall panels and access doors that deflect no more than L/240 when
subjected to +/- 8” w.g. ‘L’ is the panel-span length and ‘L/240’ is the deflection [Tip 13]: When static pressure in a
unit changes and panels deflect, leakage
at panel midpoint.
occurs. Over time, panels experience metal
fatigue, leading to even more leakage.
L. Provide floors and roofs that deflects no more than L/240 when subjected to a
This wastes energy and compromises IAQ.
300 lb load at mid-span. ‘L’ is the panel-span length and ‘L/240’ is the deflection Spec L/240 for the most rigid and leak-free
at panel midpoint. casing. Specifying sheet metal gauges does
not guarantee rigid panels. Foam-insu-
M. Provide outdoor AHUs with a roof system that deflects no more than L/240 when lated panels may be required to meet this
performance.
subjected to a snow load of 30 lb/ft2. ‘L’ is defined as the panel-span length and
‘L/240’ is the deflection at the panel midpoint.
[Tip 14]: Floor systems are the most
N. Provide outdoor AHUs with a roof sloped at a minimum pitch of 1/4” per foot. prone to leakage than the other panels of
The roof shall overhang side and end panels by a minimum of 2”. the casing. Every time someone walks on
the AHU floor, panels deflect, leading to
O. Provide an exterior finish on outdoor units that shows a breakdown of less than leakage and sweating. Spec L/240 for the
most rigid and leak-free floor. Specifying
1/8” on either side of a scribed line when subjected to ASTM B117 500 hour, sheet metal gauges does not guarantee
5% salt spray conditions. This is equivalent to an ASTM D1654 rating of ‘6’. rigid a rigid floor. Foam-insulated panels
may be required to meet this performance.
2.06 PRIMARY DRAIN PANS

[Tip 15]: On outdoor units, roof panels
A. Provide drain pans that comply with requirements for the AHU casing (Section are more prone to leakage than wall panels
2.07). due to high thermal stress and snow loads.
Ensure that performance is achieved on the
B. Comply with the stated intent of ASHRAE Standard 62. roof by specifying L/200 or higher.
C. Provide a drain pan under each cooling coil and humidifier. Drain pans for cooling
coils and humidifiers shall meet the requirements of ASHRAE 62. [Tip 16]: Poorly designed drain pans
are often breeding grounds for mold and
D. Provide drain connection made of same material as drain pan. Do not use dis- poor IAQ. ASHRAE 62-2001, section 5.11.1
states that drain pans “…shall be sloped
similar metals because of the risk of galvanic corrosion. Weld connection to the at least 1/8” per foot from the horizontal to-
drain pan. ward the drain outlet…whether the fan is in
the on or off position.” Section 5.11.2 states
E. Drain pan shall be double wall with an R-value of 12 hr-ft2-°F/BTU. The entire that “The drain pan outlet shall be located at
area of the drain pan shall have this level of thermal performance. the lowest point(s) of the pan.”
F. Insulate plumbing associated with drain pan drains and connections. [Tip 17]: Some drain pan designs may
call for less insulation at the lowest points
G. Provide drain pan under the complete width and length of cooling coil and of the pan.
humidifier sections.
H. Drain pan shall allow visual inspection and physical cleaning on 100% of the [Tip 18]: This plumbing is difficult to
access and service. Uninsulated connec-
pan surface without removal of the coil or humidifier. tions may lead to sweating and puddling
beneath the unit.
JOHNSON CONTROLS 69
FORM 102.20-QG1 (808)
[Tip 19]: YORK recommends this

I. Provide a minimum of 1” clearance between the drain pan and any coil casing, clearance so that the drain pan can be
coil support or any other obstruction. cleaned and inspected without requiring coil
removal. ASHRAE 62 recommends annual
J. Provide drain pan that allows the design rate of condensate drainage regardless inspection during the cooling season and
of fan status. cleaning if necessary.
K. Provide drain pan sloped in at least two planes by at least 1/8” per foot toward
a single drain. Locate drain connection at the lowest point of the pan. Pan shall
have no horizontal surfaces.
2.07 ACCESS DOORS

A. Provide access door(s) that meet requirements for the AHU casing.
B. Provide industrial style stainless steel hinges that permit 180 degrees of door
swing.
C. Provide latches with roller cam mechanisms that ensure a tight seal. Rotating
knife-edge or “paw” latches are not acceptable.
D. Provide each door with a single handle linked to multiple latching points or a
separate handle for each latching point. Doors serving access segments shall
have an interior latch handle.
E. Provide access doors with a locking hasp to accommodate a lockout device.
F. Provide double-pane viewing windows as shown on the elevation view drawings.
Windows shall be a non-condensing type consisting of an integrated silica desic-
cant dehumidification layer. Minimum dimension shall be 3” x 8”.
2.08 PIPE CHASE CABINET

A. Provide pipe chases with double wall, insulated panels. Pipe chase shall have
the same thermal performance as the unit casing.
B. Provide a perimeter base rail and/or roof curb under the pipe chase(s) that meets
requirements for the AHU base rail and/or roof curb.
C. Manufacturer may combine the pipe chase enclosures of adjacent segments.
D. Provide a minimum pipe chase depth, as shown on drawings. Pipe chase depth is
the clear inside dimension from inner pipe chase surface to outer unit surface.
E. Manufacturer may ship pipe chases separate from AHU if the chases are pro-
vided with lifting lugs for field installation per the AHU base rail requirements.
Manufacturer shall provide step-by-step instructions with illustrations for proper
pipe chase installation.
2.09 ROOF CURBS

A. Provide factory-fabricated galvanized steel roof curb for outdoor units. Roof
curb shall support the full-perimeter of the air handling equipment, including
pipe chases.
B. Match roof curb to roof slope. Curb surface shall be level in both axes.
C. Provide wood nailing strip to which roofer may nail roof flashing.
D. Ship roof curb loose for field installation prior to unit placement.
2.10 FANS
A. Provide double width double inlet (DWDI) housed fans or single width single
inlet (SWSI) plenum fans as equipment schedule and drawings.
70 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
B. Airfoil fans shall comply with AMCA standard 99 2408 69 and 99 2401 82.
Provide an AMCA Seal on airfoil fans. Airfoil fan performance shall be based
on tests made in accordance with AMCA standards 210 and comply with the
[Tip 20]: True airfoil fans are desirable
requirements of the AMCA certified ratings program for air performance. as they offer higher efficiency and have a
non-overloading fan characteristic.
C. Provide fans with true airfoil blades unless otherwise scheduled.
D. Provide fans with the following accessories:
1. Fan inlet screens in the inlets of fan housing (REQUIRED on SWSI plenum
fans)
2. Access door inlet screen (on AHU casing)
3. OSHA-compliant belt guard enclosing the fan motor and drive
E. Provide airfoil fans with blades formed of extruded aluminum, as scheduled.
Bent sheet metal blades are not acceptable.
F. Provide an access door in the fan scroll, as shown on drawings.
G. Provide fans with polished steel shafts with first critical shaft speed at least 125%
of the maximum operating speed for the fan pressure class. Shaft shall have an
anti-corrosion coating.
H. Provide fan motor on an adjustable base to allow adjustable and consistent belt
tension.
I. Mount the fan and motor assembly on a common adjustable base. [Tip 21]: Under no circumstances
This common base shall attach to vibration isolators, which mount to structural should the fan and motor assembly mount
to the AHU casing floor. This would lead
support channels. These channels shall span the AHU floor and mount directly
to excess casing vibration poor acoustics,
to the AHU frame. Manufacturers not complying with this requirement must panel fatigue and air leakage.
submit detailed structural and weight data to a licensed structural engineer for
review and stamped certification. The mechanical engineer shall review these
engineers’ final reports prior to submittal approval.
J. Provide vibration isolation springs with 1” or 2” static deflection, as scheduled.
K. Connect DWDI fans to the unit casing or bulkheads with canvas flexible con-
nection.
L. Provide horizontal thrust restraints between AHU casing and fan housings with
end discharge. This requirement applies to the following cases:
1. SWSI fans operating at greater than 3” of total static pressure
2. DWDI airfoil fans operating at greater than 6” of total static pressure
3. DWDI airfoil fans operating at greater than 3” of total static pressure
[Tip 22]: L-50 implies that bear-
2.11 BEARINGS AND DRIVES ings have a 50% chance of failure during
200,000 hours of operation. L-10 bearings
A. Provide bearings complying with ANSI/AFBMA 9 for fatigue life ratings. have only a 10% chance of failure during
the same time period.
B. Provide fan bearings with an average life L50 of at least 200,000 hours.
[Tip 23]: L-50 implies that bear-
C. Provide fan bearings with an average life L10 of at least 200,000 hours, as ings have a 50% chance of failure during
scheduled. 200,000 hours of operation. L-10 bearings
have only a 10% chance of failure during
D. Provide permanently lubricated bearings on forward curved fans smaller than the same time period.
18.” On other fans, provide re-greaseable bearings with hydraulic grease fittings
and lube lines extended to the motor side of the fan or to the exterior of the unit
(primary access side).
[Tip 24]: Direct drive plenum fans
provide higher levels of efficiency and are
E. Provide plenum fans with direct-drive transmissions.
typically quieter than belt-driven fans.
JOHNSON CONTROLS 71
FORM 102.20-QG1 (808)
F. Provide drives selected with a 1.5 service factor. Sheaves shall be machined from
a close grain cast iron and statically balanced by the manufacturer. Provide a
fixed pitch sheave on the motor.
G. Provide fixed pitch sheaves on both the fan and motor. Fans with motors rated
at 15 hp or less may be field balanced using variable pitch sheaves. Provide
fixed pitch sheaves when final balance is complete. Air balancer shall select and
provide final set of sheaves.
H. Provide multiple belt drives on belt driven fans with motors 10 hp or greater.
Belts shall be V-type, precision molded, raw edge construction, anti-static, oil-
resistant and heat-resistant.
2.12 ELECTRICAL MOTORS

A. Provide fan motors built in accordance with the latest standards of the NEMA
and IEEE.
[Tip 25]: ASHRAE 90.1 has a detailed
B. Provide AHU and fan motors in compliance with ASHRAE 90.1. requirement for motor efficiency – typi-
cally requiring what manufacturer’s call
C. Provide fan motors with the following characteristics: “premium” efficiency motors. 90.1 also has
a detailed requirement for motor SIZE,
1. 60 hertz, 1750 rpm operation depending on the application, static pres-
sure, etc.
2. Service factor of 1.15
3. Premium efficiency, or as required to meet ASHRAE 90.1
4. NEMA design ball bearing type
5. Rated for continuous duty at full load in a 104°F (40°C) ambient
6. Open drip proof (ODP) or totally enclosed, fan cooled (TEFC) as
scheduled.
7. Suitable for use in variable frequency application, per NEMA MG-1 Part
30
8. Inverter ready per NEMA STD MG1 PART 31.4.4.2
D. Provide direct drive plenum fans coupled to motors with matching speed, as
scheduled.
2.13 FAN-MOTOR DISCONNECTS

A. Provide UL or ETL listed fan-motor disconnects and associated components, as
scheduled and shown on drawings. Disconnects shall comply with applicable
provisions of the National Electric Code.
B. Provide fused or non-fused fan-motor disconnects in NEMA 1, NEMA 3R,
NEMA 4, or NEMA 12 enclosures, as scheduled and shown on drawings.
C. Mount disconnects on the primary access side of the associated fan segment.
1. Mount unit main disconnect (on units with single point power) on the primary
access side of supply fan section.
D. Disconnect shall be suitable for use as an OSHA lockout/tagout disconnect when
applied in accordance with part IV, Department of Labor OSHA 29 CFR Part 1910,
Control of Hazardous Energy Source (lockout/tagout): final rule.
E. Disconnect handles shall be lockable in the “off” position with up to three pad-
locks. Switch mechanism shall be directly lockable in the “off” position via
padlock when door is open.
72 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
F. Provide disconnects with integral ground lug.

1. Provide two (2) #14 ground wires on 16A to 100A disconnects.
2. Provide one (1) #6-250 ground wire on 200A to 400A disconnects.
G. Provide auxiliary contacts, as scheduled.
2.14 FAN-MOTOR STARTERS

A. Provide UL or ETL listed motor starters and associated components, as scheduled
and shown on drawings. Starters shall comply with applicable provisions of the
National Electric Code.
B. Provide starter in a NEMA 3R enclosure.
C. Mount starter on the primary access side of its associated fan section, and wire
starter to motor, unless shown otherwise on drawings.
D. Provide the following features in each starter panel:
1. Main power block
2. Motor contactor(s)
3. Individual starter short circuit and overload protection devices
4. Two primary control fuses, one secondary control line size fuse
5. Three phase ambient compensated overload heater elements
6. 115-volt control power transformer with primary and secondary protection
7. Five-point terminal strip for field control connections
8. Factory wired, non-fused or fused main power disconnect, integral with
starter panel
9. Integrated on/off auto switch.
10. Wiring to fan motor
E. Starters on outdoor units shall be suitable for use in ambient temperatures from
5°F to 104°F:
1. Provide low ambient temperature kit suitable for use down to -20°F.
2. Provide high ambient temperature kit suitable for use up to 135°F.
2.15 FAN-MOTOR VARIABLE FREQUENCY DRIVES (VFDS)

A. Provide UL or ETL listed VFDs and associated components, as scheduled and
shown on drawings. VFDs shall comply with applicable provisions of the Na-
tional Electric Code.
B. Mount VFDs in a dedicated NEMA 1 compartment located on the primary ac-
cess side of its associated fan section and wire VFD to motor, unless otherwise
indicated on drawings.
C. Enclose outdoor VFDs in a NEMA-3R enclosure.
D. VFDs on outdoor units shall be suitable for use in ambient temperatures from
5°F to 104°F:
1. Provide low ambient temperature kit suitable for use down to -20°F.
2. Provide high ambient temperature kit suitable for use up to 135°F.
JOHNSON CONTROLS 73
FORM 102.20-QG1 (808)
E. After unit installation, VFD shall be started and programmed by a factory trained
and employed service technician. Refer to Section 3.05.
F. Provide the following VFD disconnect and bypass option:
1. Fused main disconnect [Tip 26]: Select from item a, b, c or d.
Consider that VFDs are a mature, proven
2. 2 contactor VFD bypass and highly reliable technology. Bypass
packages are therefore not as important as
3. 2 contactor VFD bypass with fused disconnect they used to be. Perhaps specifying a spare
drive in lieu of bypass packages on drives is
4. 2 contactor VFD bypass with non-fused disconnect a better value for the owner.
G. Provide harmonic distortion feedback protection:

1. Equivalent 5% impedance input line reactor
2. Integral RFI/EMI filtering to meet EMC EN61800-3 for First Environ-
ment
H. Provide a user interface with the following features:
1. 30 Character multi-lingual alphanumeric display
2. Parameter set-up and operating data
3. Display data shall include:
a. output frequency (Hz)
b. speed (RPM)
c. motor current
d. calculated % motor torque
e. calculated motor power (kW)
f. DC bus voltage
g. output voltage
h. heat sink temperature
i. elapsed time meter (re-settable)
j. kWh (re-settable)
k. input / output terminal monitor
l. PID actual value (feedback) & error
m. fault text
n. warning text
o. scalable process variable display
I. Provide VFD with the following protection circuits:
1. over current
2. ground fault
3. over voltage
4. under voltage
5. over temperature
6. input power loss of phase
7. loss of reference/feedback
74 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
8. adjustable current limit regulator

J. VFD shall be UL 508C approved for electronic motor overload (12t).
K. Provide high input transient protection and surge suppression
1. 4 MOVs ahead of diode bridge
2. 120 Joule rated 1600V diode module
3. Compliant with UL 1449 / ANSI 61.4
L. Provide the following communication features:
1. Two programmable analog inputs
2. Six programmable digital inputs
3. Two programmable analog output
4. Three programmable digital relay outputs
5. Modbus RTU Communications protocol
6. Adjustable filters on analog inputs and outputs
7. Input speed signals, including 4-20 mA and 0-10 VDC
8. Accel/Decel contacts (floating point control)
9. Auto restart (customer selectable and adjustable)
10. Start/Stop options shall include 2 wire (dry contact closure), 3 wire (mo-
mentary contacts), application of input power, and application of reference
signal (PID sleep/wake-up)
11. Integrated control interface for Siemens FLN, Johnson N2, Modbus RTU,
or BACnet MS/TP or LONworks over RS-485.
M. Provide the following functions:
1. Premagnetization on start
2. DC braking/hold at stop
3. Ramp or coast to stop
4. Seven preset speeds
5. Three critical frequency lockout bands
6. Start function shall include ramp, flying start, automatic torque boost, and
automatic torque boost with flying start
2.16 FACTORY INSTALLED ELECTRICAL ACCESSORIES

A. In addition to motor power terminals, provide an independent power terminal for
convenience receptacles and lights. Provide switches as shown on drawings.
B. Provide incandescent or fluorescent lights in segments as scheduled or shown
on drawings. Provide light switches as scheduled or shown on drawings.
C. Provide a 1-hour timer on external light switches.
D. Provide a 120v convenience receptacle on supply fan segment.
2.17 HEATING AND COOLING COMPONENTS

A. Provide coils manufactured by AHU manufacturer, except where noted in contract
documents.
JOHNSON CONTROLS 75
FORM 102.20-QG1 (808)
B. Coils shall meet or exceed performance scheduled on drawings.

1. When applicable, provide coils with performance certified in accordance
with ARI Standard 410 for coil capacity and pressure drop. Circuit coils
such that the fluid velocity is within the range of certified rating conditions [Tip 27]: Coils with higher face
velocities are more vulnerable to moisture
at design flow. carryover. A coil’s vulnerability to conden-
sate carryover depends on the coil design.
C. Provide cooling coils with a maximum face velocity of 550 fpm or 500 fpm or Coils with densely packed fins (12 or 14 fpi)
450 fpm. Face velocity calculations shall be based on the finned area of the are more vulnerable. Coils with staggered
coil. tube arrangements (YORK standard) are
less vulnerable. The cleanliness of a coil
D. Provide cooling coil drain pan that is sufficient to contain coil condensate. Drain also matters.
pan shall extend a minimum of 6” or 10” or 14” downstream of the face of the
coil. [Tip 28]: YORK coils are designed
and selected to prevent moisture carryover.
E. Provide coil segment casing to accommodate full-face or reduced-face coils as However, dirty coils or coils operating
under non-design conditions may lead
scheduled. Provide face and bypass coil segments with factory installed bypass to carryover moisture. Therefore, YORK
damper. recommends at least 6” of drain pan down-
stream to catch moisture. More drain pan is
F. Provide at least 18” or 24” or 30” of access between coils. Provide an easily better, as it will keep moisture from reaching
operable access panel or door, as shown on drawings. downstream components such as fans and
fan motors.
G. Provide coil segment casing that meets or exceeds casing performance of the
unit.
[Tip 29]: Because the coil segment is
H. Provide panels that are easily removable with no special tools. the coldest part of the AHU, thermal perfor-
mance, leakage and deflection are critical
I. Locate access doors to provide clearance for pipe insulation, connectors, and here. Cooling coil drainpans are typically
accessories. Space shall allow a minimum of 90 degrees of door swing. the root of an AHU’s IAQ problems, making
performance even more critical.
J. Provide coils built in their own full perimeter frame. Tube sheets on each end
shall have fully drawn collars to support and protect tubes. Horizontal coil casing
and support members shall allow moisture to drain. Casing and support members
shall not block finned area.
K. Individual coils shall be removable from the side of the AHU.
L. Provide an intermediate drain pan on stacked cooling coils. Intermediate drain
pan shall slope in a minimum of two planes toward a single drain connection.
M. Provide a single intermediate vertical coil support on coils with a finned length
greater than 62”. Provide two vertical supports on coils with a finned length
greater than 100”, and three vertical supports on coils with a finned length greater
than 141”.
N. Extend coil connections through AHU casing. Provide a 1/4” FPT plugged
vent/drain tap on each connection. Circuiting shall allow complete draining and [Tip 30]: Coil penetrations are a very
common leakage point. Not only can air
venting when installed. Vent and drain connections shall be on the coil connec-
leak through the casing, but it can also leak
tion extension outside of the unit casing. into individual panels. This leads to a loss
in IAQ and energy efficiency performance.
O. Insulate gap between coil stub out connection and AHU casing with a spool- Spec a tight seal by specifying coil connec-
shaped sleeve grommet. Adhesive rings applied the casing walls are not accept- tions that are extended through the casing,
and by specifying a spool-shaped grommet
able.
seal that isolates the coil connection from
the panel, and that isolates the interior of
P. Water and glycol coils shall be operable at 250 psig working pressure and up to
the unit from the exterior. Coil penetrations
300° F. Factory test water and glycol coils with 325 psig compressed air under are a very common leakage point. Not only
water. can air leak through the casing, but it can
also leak into individual panels. This leads
Q. Direct expansion (DX) coils shall conform to ANSI B9.1 (Safety Code for Me- to a loss in IAQ and energy efficiency per-
formance. Spec a tight seal by specifying
chanical Refrigeration) when operating with a maximum refrigerant pressure of
coil connections that are extended through
250 psig. Factory test DX coils with 325 psig compressed air under water. the casing, and by specifying a spool-
shaped grommet seal that isolates the coil
connection from the panel, and that isolates
the interior of the unit from the exterior.
76 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
R. Steam distributing coils shall be operable at 50 psig pressure and a corresponding

saturated steam temperature of 298° F. Factory test steam coils with 315 psig
compressed air under water. Dehydrate and seal coils prior to shipping.
S. Provide steam-distributing coils with a tube outer diameter (OD) of 1” and an
inner distribution tube of 5/8” O.D. Circuit coils for gravity drain of condensate
without trapping. Steam shall discharge in the direction of condensate flow to
ensure even heat transfer across each tube.
T. Provide water, glycol and DX coils with a tube OD of 5/8” or 1/2”. Mechanically
expand tubes to form fin bond and provide burnished, work-hardened interior
surface. Tubes shall have a minimum tube wall thickness of 0.020” or 0.025” or
0.035” or 0.049” for 5/8” tubes, and 0.016” or 0.020” or 0.032” for 1/2” tubes.
[Tip 31]: The outer radius of a coil
U. Provide coils with copper tube return bends with the following final minimum tube’s return bend can be very vulnerable to
thicknesses: premature failure. Tubes that are machine
bent to create a return bend are especially
1. 0.035” for 5/8” diameter tubes susceptible to failure, as the outer radius of
the bend is stretched and has a final thick-
2. 0.032” for 1/2” diameter tubes with 0.020” or 0.032” tube wall thickness that is significantly thinner than the
initial tube thickness. Specifying and enforc-
nesses ing a FINAL thickness of .035” at the outer
radius of the return bend will help ensure a
3. 0.020” for 1/2” diameter tubes with 0.016” tube wall thickness. robust and long-lasting coil
V. Provide water, glycol and steam coil headers made of seamless copper or brass
tubing. Pipe connections shall be steel or red brass. Header connections (tubes
and piping connections) shall be silver-brazed or TIG welded.
W. Provide DX coils with brass distributor and solder-type connections. Suction
and discharge connections shall be on the same end regardless of coil depth.
Mount refrigerant specialties outside of unit. Provide DX coils with a hot gas
bypass port on distributor.
X. Provide coils with die-formed, continuous aluminum or copper fins. Fins shall
have fully drawn collars to accurately space fins and protect tubes. Fins shall be
0.006” or 0.008 or 0.01” thick.
Y. Provide coil coatings as scheduled or indicated on drawings.
2.18 FILTERS
A. Provide filter segments and filters as scheduled. [Tip 32]: Face loading filters offer a
tighter seal and less air bypass than side
B. Provide side loading filters for filter segments located upstream of coil segment(s) loading filters. For performance reasons,
with an access door on the drive side through which filters can be easily loaded. it is best to not use side loading filters in
downstream or “final” positions, where the
C. Provide face loading filters for segments located downstream of coil segment(s). filters typically have high efficiencies. Be
Provide an 18” (minimum) access plenum and access door on the drive side sure to specify generous access, as they
require space upstream or downstream of
through which face loading filters can be easily loaded. the rack to change filters.
D. Provide filter racks integral to the unit and constructed of galvanized steel or
stainless steel.
E. Provide Class 2 or Class 1 filter media per U.L. 900 and as required by local
codes.
F. Filter types, efficiencies, and nominal depths shall be as follows:
1. Flat filters – 2” throwaway, 2” permanent cleanable, 2” 30% pleated, or 4”
30% pleated filters, as scheduled.
2. Angled filters – 2” throwaway, 2” permanent cleanable, or 2” 30% pleated
filters, as scheduled.
JOHNSON CONTROLS 77
FORM 102.20-QG1 (808)
3. Rigid filters – 4” mini pleated, 12” rigid, or 22” bag filters with efficiencies
of 60-65% (MERV 11), 80-85% (MERV 13), 90-95% (MERV 14), or 90-
95% (MERV 15), respectively; as scheduled.
a. Provide a pre-filter rack in rigid filter segments. Pre-filters shall have 2”
throwaway, 2” permanent cleanable, 2” 30% pleated, or 4” 30% pleated
filters as scheduled.
4. Carbon filters – 2” deep rechargeable, incinerable, or disposable panels filled
with 60% activity carbon, as scheduled.
a. Carbon filtration system shall be designed for a minimum contact ef-
ficiency of 99% with a residence time of at least 0.08 seconds.
b. Provide post-filter and/or pre-filter rack in carbon filter segments with 2”
throwaway, 2” permanent cleanable, 2” 30% pleated, or 4” 30% pleated
filters, as scheduled.
5. HEPA filters – 12” 99.97%, or 99.99% efficient media, as scheduled.
a. Performance of installed filtration system shall be certified via a DOP test
and classified as UL Class 1 when tested in accordance with UL Standard
586.
b. Filter frame shall be specifically developed for HEPA filters, with ap-
propriate quantities of filter clamps.
G. Provide a flush mounted, factory installed magnahelic differential pressure gage
on the drive side of unit to measure pressure drop across filters. Manufacturer
shall provide fully functional gauges, complete with tubing.
2.19 DAMPERS
A. Provide dampers tested in accordance with AMCA 500.
B. Provide factory-installed dampers, as shown on drawings.
C. Dampers shall have airfoil blades, extruded vinyl edge seals, and flexible metal
compressible jamb seals.
D. Dampers shall have a maximum leakage rate of 4 CFM/square foot at 1” w.g.,
and shall comply with ASHRAE 90.1.
E. Damper blades shall be parallel acting unless otherwise indicated.
F. Damper blades shall be galvanized steel or aluminum, as scheduled.
2.20 AIRFLOW MONITORING STATIONS

A. Provide airflow monitoring stations, as scheduled or shown on drawings.
B. Provide airflow monitoring stations tested in accordance with AMCA Standard
611 in an AMCA registered laboratory. Airflow monitoring stations shall bear
the AMCA Ratings Seal for Airflow Measurement Performance.
C. If airflow station incorporates a control damper, control damper shall comply
with leakage rates per ASHRAE 90.1 and with specification section 2.19 DAMP-
ERS.
D. Provide a factory-installed transducer that sends a CFM-proportional, 4-20 mA
or 0-10V signal, as specified.
2.21 DIFFUSERS
A. Provide diffuser segments as shown on drawings.
78 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
B. Diffuser plates shall ensure proper air flow across components downstream of
DWDI fans.
2.22 APPURTENANCES
A. Provide rain hoods on outdoor unit air intakes, as shown on drawings. Provide
moisture screens on outdoor air inlet rain hoods.
B. Provide safety grates over bottom openings, as shown on drawings.
1. Safety grates shall be capable of supporting a 300 lb. center load.
2.23 FINISHES
A. Manufacturer shall clean the exterior surfaces of units prior to finishing, painting,
or shipment.
B. Manufacturer shall paint outdoor units prior to shipment. Manufacturer shall
paint indoor units, as scheduled or shown on drawings.
1. Manufacturer shall apply a primer prior to painting units.
2. Manufacturer shall apply a finish coat of acrylic polyurethane paint.
3. Finished unit shall exceed 500-hour salt spray solution (5%) test without
any sign of red rust when tested in accordance with ASTM B-117.
2.24 TESTS AND INSPECTIONS

A. Manufacturer shall dynamically balance fan/motor/base assembly.
1. Balance constant volume fan assemblies at design RPM.
2. Balance variable volume fan assemblies from 10% to 100% of design
RPM.
3. Take filter-in measurements in the horizontal and vertical axes on the drive
and opposite-drive sides of fan shafts.
4. Take filter-out measurements in the horizontal, vertical, and axial axes on
the drive and opposite-drive side of fan shafts.
5. Constant speed fan vibration limits: filter-in measurements shall not exceed
4 mils. Filter-out measurements shall not exceed 6 mils in the horizontal
and vertical axes, and 7 mils in the axial axis.
6. Variable speed fan vibration limits: filter -in measurements shall not exceed
7 mils. Filter-out measurements shall not exceed 9.5 mils.
B. Manufacturer shall hipot test wiring intended to carry voltages greater than
30Vac.
2.25 VERIFICATION OF PERFORMANCE

A. Factory test one out of every five AHUs (or a minimum of one unit) to verify
compliance with airflow, static pressure, casing leakage, and panel deflection
requirements. Owner and engineer reserve the right to select units to be tested.
Manufacturer shall pay food, lodging, and travel expenses for up to two wit-
nesses.
1. Alternatively, field test units to verify compliance with airflow, static pres-
sure, casing leakage, and panel deflection requirements. Follow testing pro-
cedures outlined in this specification. Manufacturer shall hire a mechanical
engineer of record to supervise testing.
JOHNSON CONTROLS 79
FORM 102.20-QG1 (808)
B. One representative from both the owner and the engineer shall witness the test.
Manufacturer shall pay food, lodging and transportation expenses for two wit-
nesses.
C. Perform test on a fully assembled unit with sections joined per manufacturer’s
installation instructions. Use of additional material (tape, sealant, caulk) is not
acceptable.
D. Perform tests to verify the following performance criteria: [Tip 33]: Make sure that bidders to
your specification are held accountable for
1. Casing leaks no more than 1% of design CFM at +/-8” w.g. their performance. Specifying leakage and
deflection tests are an important part of
2. Casing panels deflect no more than L/240 at +/-8” w.g. ‘L’ is defined as the ensuring the owner gets the performance
that was specified.
panel span length and ‘L/X’ is the deflection at panel midpoint.
E. Unit shall meet the Large Missile Impact Test for AHU casing (walls, roof, and
doors) and base. Unit shall carry a Notice of Acceptance (NOA) from the Mi-
ami-Dade County Product Control Division. Label equipment per NOA labeling
instructions.
[Tip 34]: It is not practical or reason-
F. Provide written letter of guarantee from manufacturer stating that no condensa- able to test for thermal performance or
sweating. However a manufacturer should
tion will form on the exterior of units, under given design conditions.
know their performance capabilities and
should willingly write this letter.
G. Should a unit fail a test, treat unit with a permanent remedy at manufacturer’s
expense until test is successfully passed.
2.26 FACTORY TEST SETUP AND METHODS

A. AHU Preparation
1. Assemble and seal AHU sections per manufacturer’s installation manual.
2. Close and latch access doors. No additional sealing is permitted.
3. Seal duct, damper and louver openings.
4. Blank off and seal supply fan opening(s).
5. Blank off and seal supply fan bulkhead to isolate positive and negative
pressure sections.
B. Pressurization procedure
1. Pressurize positive pressure side to specified static pressures using a pres-
sure blower.
2. Pressurize negative pressure side to specified static pressures using a pres-
sure blower.
3. Measure and monitor differential pressure exerted on the cabinet with a
pressure gage.
C. Test measurement
1. Measure panel deflections at the centers (length and width) or four panels
chosen by owner and engineer.
2. Measure pressure drop through an ASME long radius nozzle, mounted n
the test module.
3. Monitor leakage at the same time panel deflection is measured.
D. While under pressure, inspect units failing to meet specified leakage and deflec-
tion. Treat failing areas with a permanent remedy. Repeat test and inspection.
Re-treat unit as necessary to pass both tests.
E. Provide test data and results in a complete report to the owner.
80 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
PART 3 EXECUTION
3.01 INSTALLATION
A. Install equipment per industry standards, applicable codes, and manufacturer’s
instructions.
B. Do not use AHUs for temporary heating, cooling or ventilation prior to complete
inspection and startup performed per this specification.
C. Install AHUs on a concrete pad, roof curb, or structural steel base, as shown on
drawings.
D. Install AHUs with manufacturer’s recommended clearances for access, coil pull,
and fan removal.
E. Provide one complete set of filters for testing, balancing, and commissioning.
Provide second complete set of filters at time of transfer to owner.
F. Install AHU plumb and level. Connect piping and ductwork according to
manufacturer’s instructions.
G. Install seismic restraints and anchors per applicable local building codes. Refer
to specification Section 230548 (15240 / 15070) for product and installation
requirements.
H. Install pipe chases per manufacturer’s instructions.
3.02 FIELD QUALITY CONTROL

A. Store per AHU manufacturer’s written recommendations. Store AHUs indoors in [Tip 35]: Improper storage can de-
a warm, clean, dry place where units will be protected from weather, construc- grade the longevity and performance of an
AHU. Rust and bacteria may form if units
tion traffic, dirt, dust, water and moisture. If units will be stored for more than
are not kept dry. IAQ and energy efficiency
6 months, follow manufacturer’s instruction for long-term storage. may be negatively impacted once improp-
erly stored AHUs are operating.
B. Rig and lift units according manufacturer’s instructions.
3.03 AHU INSPECTION

[Tip 36]: A thorough inspection and
A. Hire manufacturer’s factory-trained and factory-employed service technician to necessary corrections ensure a proper
installation. A proper installation is neces-
perform an inspection of unit and installation prior to startup. Technician shall
sary to fully realize the energy, IAQ and
inspect and verify the following as a minimum: acoustical benefits of a high-performance
AHU and system.
1. Damage of any kind
2. Level installation of unit
3. Proper reassembly and sealing of unit segments at shipping splits.
4. Tight seal around perimeter of unit at the roof curb
5. Installation of shipped-loose parts, including filters, air hoods, bird screens
and mist eliminators.
6. Completion and tightness of electrical, ductwork and piping connections
7. Tight seals around wiring, conduit and piping penetrations through AHU
casing.
8. Supply of electricity from the building’s permanent source
9. Integrity of condensate trap for positive or negative pressure operation
10. Condensate traps charged with water
11. Removal of shipping bolts and shipping restraints
JOHNSON CONTROLS 81
FORM 102.20-QG1 (808)
12. Sealing of pipe chase floor(s) at penetration locations.

13. Tightness and full motion range of damper linkages (operate
manually)
14. Complete installation of control system including end devices and
wiring
15. Cleanliness of AHU interior and connecting ductwork
16. Proper service and access clearances
17. Proper installation of filters
18. Filter gauge set to zero
B. Resolve any non-compliant items prior to proceeding with the inspection of the
fan assembly.
3.04 INSPECTION AND ADJUSTMENT: AHU FAN ASSEMBLY

[Tip 37]: A thorough inspection and ad-
A. Hire the manufacturer’s factory-trained and factory-employed service technician justment of the fan assembly helps ensure
perform an inspection of the AHU fan assembly subsequent to general AHU that the energy, IAQ and acoustical benefits
inspection and prior to startup. Technician shall inspect and verify the following of a high-performance AHU and system are
realized.
as a minimum:
1. Fan isolation base and thrust restraint alignment
2. Tight set screws on pulleys, bearings and fan
3. Tight fan bearing bolts
4. Tight fan and motor sheaves
5. Tight motor base and mounting bolts
6. Blower wheel tight and aligned to fan shaft
7. Sheave alignment and belt tension
8. Fan discharge alignment with discharge opening
9. Fan bearing lubrication
10. Free rotation of moving components (rotate manually)
B. Manufacturer shall perform service to bring fan performance within factory
specifications.
3.05 STARTUP SERVICE AND OWNER TRAINING

A. Manufacturer’s factory-trained and factory-employed service technician shall
startup AHUs. Technician shall perform the following steps as a minimum:
1. Energize the unit disconnect switch
2. Verify correct voltage, phases and cycles
3. Energize fan motor briefly (“bump”) and verify correct direction of rota-
tion.
4. Re-check damper operation; verify that unit cannot and will not operate
with all dampers in the closed position.
5. Energize fan motors and verify that motor FLA is within manufacturer’s
tolerance of nameplate FLA for each phase.
82 JOHNSON CONTROLS
FORM 102.20-QG1 (808)
B. Provide a minimum of 4 hours of training for owner’s personnel by manufac-

turer’s factory-trained and factory-employed service technician. Training shall
include AHU controls, motor starter, VFD, and AHU.
C. Training shall include startup and shutdown procedures as well as regular opera-
tion and maintenance requirements.
D. If AHU is provided with a factory-mounted variable frequency drive (VFD), hire
the VFD manufacturer’s factory-trained and factory-employed service technician
to inspect, test, adjust, program and start the VFD. Ensure that critical resonant
frequencies are programmed as ‘skip frequencies’ in the VFD controller.
E. Submit a startup report summarizing any problems found and remedies per-
formed.
3.06 FIELD PERFORMANCE VERIFICATION [Tip 38]: A field leakage test is a pru-
dent step to ensure that the AHU performs
A. Leakage: Pressurize casing to +/-8” w.g. and measure leakage. Pressurize casing as promised. The test is a final confirmation
to –8”w.g. and measure leakage. If leakage exceeds 1% of design airflow, seal that the AHU will perform. Field testing con-
leakage points with a permanent solution. Repeat test. If the AHU still does not firms that the AHU withstood the stresses
of shipping, rigging and installation and can
pass, contact the manufacturer to seal unit. still provide high performance.
B. Submit a field test report with testing data recorded. Include description of cor-
rective actions taken.
3.07 CLEANING
A. Clean unit interior prior to operating. Remove tools, debris, dust and dirt.
B. Clean exterior prior to transfer to owner.
3.08 DOCUMENTATION
A. Provide Installation, Operation & Maintenance Manuals in the supply fan
section of each unit. Provide six additional copies for owner’s project system
manual.
B. Provide six copies of Spare Parts Manual for owner’s project system manual.
JOHNSON CONTROLS 83
Printed on recycled paper
Form: 102.20-QG1 (808) Supersedes: 102.20-QG1 (707)

© 2008 Johnson Controls, Inc. P.O. Box 423, Milwaukee, WI 53201 Printed in USA
www.johnsoncontrols.com

Air Handling Units - Equipment Guide

Uploaded by

Copyright:

Available Formats

Air Handling Units - Equipment Guide

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Air Handling Units - Equipment Guide

Uploaded by

Copyright:

Available Formats

What are some of the features and components described in the document?

What are some of the features and components described in the document?

What are some of the testing and certification procedures mentioned?

What are some of the testing and certification procedures mentioned?

FORM 102.

SOLUTION AIR HANDLING UNITS

GENERAL INFORMATION STAGGERED COIL OPTIONS

Introduction Assurance of Johnson Controls Backing

Quick and Easy selection

• Save Time – choose components and

Configuration 1 (Stacked Unit) – Configuration 2 (Stacked Unit) –

Configuration 3 – Minimum frills. Maximum IAQ

Configuration 4 – Exhaust air flexibility with gas-heat and humidification

Configuration 5 – Cooling-only lab design with HEPA filtration

Configuration 6 – Classic hospital design with return fan economizer operation.

Flexibility of Design Component Flexibility

Energy Savings Factory Installation

FIG. 1 – DAMPER OPTIONS

State-of-the-Art Certification & Testing

Multi-Sloped Drain Pans Improve Cost Savings

A Complete Line of Filters

Light pre-filtering duty: Stringent filtration requirements: Odor or VOC removal

Energy Consumption Rearranging Equation 1 to solve for duct leakage class:

EPAct Efficient Performance

Energy Saving Air-Modulator™ 3. Eliminates need for motor

FAN APPLICATION REVIEW

• The BHP varies as a cube of the RPM:

FIG. 2 – CURVE AT VARIOUS RPMs

on the system curve created by Point A.

AIRFLOW – CFM (100)

FIG. 3 – FAN CURVE WITH TWO SYSTEM CURVES

FAN APPLICATION REVIEW

Variable Air Volume

Design CFM = 40,000 CFM = CFMd

1st: Calculate the Minimum CFM:

where: CFM1, SP1 = arbitrary point located on surge line

2nd: Calculate the Arbitrary Points:

30,000 CFM 20,000 CFM

SP2 = 3.1 SP3 = 2.1

PEAK EFFICIENCY LINE

Minimum CFM Design CFM

FIG. 4 – FAN CURVE AT VARIOUS RPMs

Solution Component Temperature Margins • Pre-filters - 150°F.

Fan Motor Heat (MBH)

Chilled water / Hot water

Solution optimizes coil performance with customized coil

AHU Chilled water cooling coil

AHU Hot water heating coil

AHU (DX) Direct Expansion cooling coil

Header material: Fin Spacing:

Heating Coils – Integral face and bypass

Integral face and bypass coil (IFB/VIFB)

Notes & Options

Heating Coils – Steam Distributing

Literature Reference — See “DX Piping Guide” – Form 050.40-ES2

SOLUTION SEGMENT IDENTIFICATION

FAN SEGMENTS HEAT SEGMENTS ACCESSORY SEGMENTS

Unit & Coil Hand Identification

LEFT HAND (LH)