Type Approval Certificate: ROXTEC International AB

Page 1 / 3
Certificate number: 04558/G0 BV

File number: ACI4000/032/004
Product code: 5302H
This certificate is not valid when presented without the full attached schedule
composed of 7 sections
www.veristar.com
TYPE APPROVAL CERTIFICATE

This certificate is issued to
ROXTEC International AB
KARLSKRONA - SWEDEN
for the type of product
CABLE PENETRATIONS IN FIRE DIVISIONS
Cable sealing system with multidiameter technology, S- Series
Requirements:
Bureau Veritas Rules for the Classification of Steel Ships Part C Chapter 4
SOLAS 74, as amended, Regulations II-2/9.3.1
IMO Res MSC.307(88) (2010 FTP Code)
IMO Res. MSC.61(67)-(FTP Code) with IMO Res MSC.307(88) (2010 FTP Code) article 8
IMO MSC/Circ.1120
This certificate is issued to attest that Bureau Veritas Marine & Offshore did undertake the relevant approval procedures for the product identified
above which was found to comply with the relevant requirements mentioned above.
This certificate will expire on: 30 Mar 2025
For Bureau Veritas Marine & Offshore,

At BV GOTHENBURG, on 30 Mar 2020,
Magne MOLLER
This certificate is recognized by Transport Canada
This certificate remains valid until the date stated above, unless cancelled or revoked, provided the conditions indicated in the subsequent page(s) are complied
with and the product remains satisfactory in service. This certificate will not be valid if the applicant makes any changes or modifications to the approved product,
which have not been notified to, and agreed in writing with Bureau Veritas Marine & Offshore. Should the specified regulations or standards be amended during
the validity of this certificate, the product(s) is/are to be re-approved prior to it/they being placed on board vessels to which the amended regulations or standards
apply. This certificate is issued within the scope of the General Conditions of Bureau Veritas Marine & Offshore available on the internet site www.veristar.com.
Any Person not a party to the contract pursuant to which this document is delivered may not assert a claim against Bureau Veritas Marine & Offshore for any
liability arising out of errors or omissions which may be contained in said document, or for errors of judgement, fault or negligence committed by personnel of the
Society or of its Agents in establishment or issuance of this document, and in connection with any activities for which it may provide.
The electronic version is available at: http://www.veristarpm.com/veristarnb/jsp/viewPublicPdfTypec.jsp?id=dzqqub7wi6

BV Mod. Ad.E 530 June 2017 This certificate consists of 3 page(s)
Page 2 / 3
THE SCHEDULE OF APPROVAL

1. PRODUCT DESCRIPTION:
A-Class Divisions "Cable sealing system with multidiameter technology, S-series"
Consisting of Roxtec S-series frames (S, SO, SF, SFO, SR, SK, SRC r20&r40 and BTB) in sizes 1-8 and combinations thereof,
welded or bolted on to the steel divisions; filled with Roxtec (standard or Ex, EMC, PE, ES, BG, BGB) halogen free insert
modules. Assembled with Roxtec Wedge kit or Roxtec EMC, Ex Wedge kit.
S-series frames 1x1 to 8+8x10
Penetration designation
Welded and bolted
Type of division tested Deck and Bulkhead
Depth of the penetration (mm) 60
External dimensions (mm) 121 x 80 to 596 x 1315
Classification A0 to A-60
Maximum cable diameter: 98 mm
Tested fill based on transit opening area and the Roxtec Cable Sealing System. Maximum fill of a Roxtec transit is to install
cable in every module installed in transit opening and minimum is to not install cable in any module in transit opening.
Additional insulation is to be provided as shown in the referred Manufacturer's drawings. Same insulation material and thickness
to be used as used for the insulation of division penetrated. The insulation thickness is to be at least the length of protruding
frame.
2. DOCUMENTS AND DRAWINGS:

As per the Manufacturer’s drawings:
- "S-series frames cables - A-Class steel blkhd": N° S1040752 Rev.B dated 28/02/2020
- "S-series frames cables - A-Class steel deck": N° S1040753 Rev.B dated 28/02/2020
- "S frames metal clad cables - A-Class steel div": N° S1040754 Rev.A dated 21/10/2014
- "S-series frames with cables - A0-Class steel deck/bulkhead": N° S1506241 Rev.A dated 08/09/2015
3. TEST REPORTS:
Laboratory Test report Date Division Fire rating Test standard
RIME, Japan N° 09-344(E) 11/12/2009 Bulkhead A-60
RIME, Japan N° 09-346(E) 11/12/2009 Deck A-60 IMO FTP Code Annex 1 Part 3 [test
DBI, Denmark N° PGA10024 21/12/2011 Bulkhead A-60 standard: IMO Resolution A.754(18)]
DBI, Denmark N° PGA10025 22/12/2011 Deck A-60
DBI, Denmark N° PGA10651 03/07/2015 Deck A-0
DBI, Denmark N° PGA10652 03/07/2015 Bulkhead A-0
SP, Sweden N° 6P02516 29/08/2016 Bulkhead A-60 IMO 2010 FTP Code Annex 1 Part 3
DBI, Denmark N° PGA10871Arev2 16/01/2018 Deck A-60
test date: 31/10/2016
4. APPLICATION / LIMITATION:
4.1 - Approved for use as cable transits in A-0, A-15, A-30 and A-60 class steel divisions, with limitations contained in §1.
4.2 - The fitting aboard to be the same as used for the test.
5. PRODUCTION SURVEY REQUIREMENTS:

5.1 - The A-Class Divisions "Cable sealing system with multidiameter technology, S-series" are to be supplied by
ROXTEC International AB in compliance with the type described in this certificate.
5.2 - This type of product is within the category HBV of Bureau Veritas Rule Note NR320 and as such does not require a BV
product certificate.
5.3 - ROXTEC International AB has to make the necessary arrangements to have its works recognised by Bureau Veritas in
compliance with the requirements of NR320 for HBV products.

Page 3 / 3
6. MARKING OF PRODUCT:
The product or packing is to be marked with manufacturer name, type, designation and fire-technical rating.
7. OTHERS:
7.1 - It is ROXTEC International AB's responsibility to inform shipbuilders or their sub-contractors of the proper methods of
fitting, use and general maintenance of the approved equipment and the conditions of this approval.
7.2 - This Certificate supersedes the Type Approval Certificate N° 04558/F3 BV issued on 22/09/2016 by the Society.
7.3 - Testing of the penetrations for gastightness and watertightness as per following inspection reports, witnessed by Third
Party surveyor:
- report N° 020400 dated 25/03/2002, from DNV, Norway.
- report N° SKM-04-4088 dated 16/06/2004 from DNV, Norway.
Watertightness test Gastightness test
(before fire exposure) (before fire exposure)
6 bar during 60 min 4 bar during 30 min
*** END OF CERTIFICATE ***


Type Approval Certificate: ROXTEC International AB

Uploaded by

Copyright:

Available Formats

Type Approval Certificate: ROXTEC International AB

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Type Approval Certificate: ROXTEC International AB

Uploaded by

Copyright:

Available Formats

Page 1 / 3

Certificate number: 04558/G0 BV

TYPE APPROVAL CERTIFICATE

This certificate will expire on: 30 Mar 2025

For Bureau Veritas Marine & Offshore,

This certificate is recognized by Transport Canada

The electronic version is available at: http://www.veristarpm.com/veristarnb/jsp/viewPublicPdfTypec.jsp?id=dzqqub7wi6

Certificate number: 04558/G0 BV

THE SCHEDULE OF APPROVAL

2. DOCUMENTS AND DRAWINGS:

5. PRODUCTION SURVEY REQUIREMENTS:

The electronic version is available at: http://www.veristarpm.com/veristarnb/jsp/viewPublicPdfTypec.jsp?id=dzqqub7wi6

Certificate number: 04558/G0 BV

* END OF CERTIFICATE *

The electronic version is available at: http://www.veristarpm.com/veristarnb/jsp/viewPublicPdfTypec.jsp?id=dzqqub7wi6

You might also like