Product Introduction

Quick Installation Guide

AC750 Dual Band WiFi Range Extender

Model No.: EX750 Power: The indicator keep lighting after powered on.

CPU: The indicator is blinking after powered on, keep fast

blinking after the RST button pressed.

5G EXT: The indicator is blinking when searching for

primary AP, keep lighting when connected.

2.4G EXT: The indicator is blinking when searching for

5G WPS: Press this button for 5G WiFi network extension. primary AP, keep lighting when connected. ON/OFF: Slide this switch to power on or off the device.

2.4G WPS: Press this button for 2.4G WiFi network LNK/ACT: The indicator will keep lighting when RST: Press this button for more than 5 seconds, the
extension. connected. device will be reset to factory default settings.

V1.1501
LAN Port: This port is used to connect the PC.
Copyrights 2015 by TOTOLINK All rights reserved. Website: http://www.totolink.net

Information in this document is subject to change without prior notice.

Method One: WiFi Extension by WPS button

One-click WPS connection makes it easy to extend the coverage of your existing WiFi network. Here we take A2004NS as primary Router.

Press the WPS button on the router for 2 seconds. Press the 2.4G WPS button on EX750 for 2 seconds. Wait for a while. Then press the WPS button on the router for 2 seconds again. Press the 5G WPS button on EX750 for 2 seconds. Wait for a while.
(SSID: TOTOLINK A2004NS) Until the 2.4G EXT indicator turns solid lighting, 2.4G WiFi network (SSID: TOTOLINK A2004NS_5G) Until the 5G EXT indicator turns solid lighting, 5G WiFi network extending
extending successfully. (SSID: TOTOLINK EX750) successfully. (SSID: TOTOLINK EX750_5G)

SSID: TOTOLINK EX750 SSID: TOTOLINK EX750

TIPS:
You can put EX750 close
2.4G 5G the router to setup WPS
connection, then unplug it
WPS WPS and place it anywhere within
the WiFi coverage. EX750
can remember the last
connected AP and firstly
connect to it when powered
on.

Method Two: Setup via Web Interface

1 Setup your PC (Connect your PC to the LAN port of EX750) 2 Setup the EX750
: :
Open any browse, type in 192.168.0.254, press Enter key.
Below the Web Interface of EX750 shows up. First click 2.4GHz Extender Setup.

Right-click “ Network — Properties Double-click “Internet Protocol Choose “Use the following IP address”,
— Local Area Connection — Properties”. Version 4 (TCP/IPv4)” IP address: 192.168.0.5, default
gateway: 192.168.0.254. Click OK--OK.
Click Setup Tool:

5 By default, AP mode selected.

Click LOGIN, the Web settings page shows up. Choose your upper router’s
SSID, here we choose zion.

Next, please do the same operation for 5GHz Extender Setup: Choose
6 Choose Extender (AP + Client) mode. 8 Select primary router’s SSID, then type in the correct Encryption key (password)
of the router. Click Apply. 10 Extender (AP + Client) mode, click AP Scan button. Select primary router’s SSID, 12 Try any website to test the Internet.
then type in the correct Encryption key (password) of the router. Click Apply.

7
click AP Scan button on right top of the page, then many SSIDs will
9 After a moment, it shows connected. 11 You can check the EX750’s status on Status Summary page, see below:
NOTE
turn up for you to choose. NOTE: EX750 allows you to change the extended SSID for extender.
So that you can keep a separated SSID for extending WiFi network,
not same as primary router.

For more information, please go to www.totolink.net