Harris, Exploring Chemical Analysis 4e Chapter 00

A chemical firm was hired to monitor a nearby lake for possible mercury
contamination. Several samples were taken at different locations around the lake,
including water samples, lake bottom samples, and plant samples. When the
chemist returned to the laboratory, the water samples were the first to be
analyzed. The analysis began by removing a number of aliquots. An aliquot is:

a) a measure of the contamination of the lake water.

b) a combined measure of the contamination in the lake.
c) a precise liquid sample taken for analysis.

The sampling technique is very important when analyzing a large area, or vast
amounts of material because you can't analyze everything. When preparing a
composite sample, a chemist would:

a) take several samples at random from pre-planed locations in the bulk sample
and analyze each.
b) take representative samples from various areas of the bulk samples and
combine them for analysis.
c) analyze as much of the bulk sample as possible.

The steps in a chemical analysis are:

a)
1. Formulate the question.
2. Select the analytical procedure
3. Sample
4. Prepare the sample
5. Make replicate measurements of the sample.
b)
1. Select the analytical procedure
2. Sample
3. Prepare the sample
4. Make replicate measurements of the sample.
5. Make a clear and complete written report of your findings.
c)
1. Formulate the question.
2. Select the analytical procedure
3. Sample
4. Prepare the sample
5. Make replicate measurements of the sample.
6. Make a clear and complete written report of your findings.

A chemist following a procedure carefully was asked to decant a solution. This

means:

a) Stir the solution thoroughly to suspend the solids and pour the mixture into a
filtering apparatus.
b) Allow any solid material to settle to the bottom of the flask, and then pour off
the liquid above the solution.
c) Pour the solution from one flask to another.

A sample is said to be homogeneous if:

a) the sample is the same throughout.

b) the sample has a different composition in different parts of the sample.
c) the sample can be separated into the individual components by filtering the
sample.

When performing an analysis a chemist often uses a standard solution. What is a

standard solution?

(a) A solution that complies with standards established by the Environmental

Protection Agency.
(b) A solution that has a concentration of a chemical that is known to a high
degree of certainty.
(c) A solution that is prepared from a chemical that has been designated as a
primary standard.

In discussing quantitative and qualitative analysis one could say:

a) the two terms are commonly used interchangeably.

b) quantitative analysis deals with determining what materials may be present in a
sample.
c) Quantitative analysis deals with the quantity of a material present in a sample.

The term masking generally refers to:

a) removing any material that may interfere with an analysis.

b) Masking generally refers to the transformation of an interfering species into a
form that is not detected.
c) selecting samples from which the identity has been masked. This procedure
prevents the analyst from prejudging the outcome of the analysis.

Interference occurs:

a) when a species other than the analyte causes an analysis to be inaccurate.

b) when the analyte is precipitated from a non-homogeneous solution.
c) when two or more methods used for separating species interfere with each
other.

Which of the following statements is incorrect.

(a) A bulk sample is taken from a lot.

(b) A bulk sample is taken from a laboratory sample.
(c) A bulk sample is also called a gross sample.
Harris, Exploring Chemical Analysis 4e Chapter 01
A biochemist is beginning to prepare 100.0 mL of a solution to be labeled "0.900%
(wt/vol) Sodium Chloride." To prepare this solution, the biochemist would:

a) Weigh 0.900 grams of sodium chloride into a container and add 100.0 mL of
water to dissolve the sodium chloride.
b) Weigh 0.900 grams of sodium chloride into a container, add water to dissolve
the sodium chloride, and then add water to produce 100.0 mL of solution.
c) Weigh 9.00 grams of sodium chloride into a container, dissolve the sodium
chloride in water, and then add water to produce 100.0 mL of solution.

A solution is prepared by dissolving 25.8 grams of magnesium chloride (MgCl 2) in

water to produce 250.0 mL of solution. Calculate the molarity of the chloride ion in
the solution.

a) 0.271 Molar
b) 1.08 Molar
c) 2.17 Molar

The Great Salt Lake, located in the state of Utah, is approximately eight times
saltier than the ocean. The salinity of the lake is said to occasionally be as high as
27 parts per thousand sodium chloride. Calculate the molarity of the sodium ion the
Great Salt Lake.

a) 4.6 X 10 -4 Molar Na+

b) 0.46 Molar Na+
c) 1.2 Molar Na+

The ethyl alcohol content of many beers produced in the United States is 4.05%
( vol/vol). If the density of ethyl alcohol at room temperature is 0.7893 grams per
mL, what is the percent of ethyl alcohol in beer expressed as percent (wt/vol)?
a) 3.20% ethyl alcohol (wt/vol)
b) 5.13% ethyl alcohol (wt/vol)
c) 7.80 ethyl alcohol (wt/vol)

An analytical procedure required the preparation of a solution containing 100.0 ppm

chromium. How many grams of potassium dichromate (K2Cr2O7) would be required
to prepare 1.000 liter of this solution?

a) 0.2829 g K2Cr2O7
b) 0.1000 g K2Cr2O7
c) 0.5658 g K2Cr2O7

Calculate the formal concentration of a sodium acetate solution prepared by diluting

45.0 mL of a solution containing 25.0 ppm sodium acetate (NaC 2H3O2) to a total of
0.500 liters of solution.

a) 6.10 x 10-4 M NaC2H3O2

b) 1.37 X 10-6 M NaC2H3O2
c) 2.75 X 10-5 molar NaC2H3O2.

Certain chemical compounds are given the label "strong electrolyte". This means:

a) that the compounds consists atoms that are bonded together by bonds that are
considered primarily covalent.
b) that the compounds when dissolved in water, dissociate into ions that will
strongly inhibit the conduction of electricity.
c) that the compounds dissociate into ions when dissolved in water and thus
facilitate the conduction of electricity through the water.

When concentrated sulfuric is sold to the chemist, the label contains no mention of
the molarity of the acid. Instead, the label normally lists the concentration of
sulfuric acid as a wt/wt percent and the density of the sulfuric acid solution. If the
solution is 98.0 (wt/wt % ) sulfuric acid, and has a density of 1.80 g/mL, calculate
the molarity of concentrated sulfuric acid.

a) 18.0 Molar
b) 18.4 Molar
c) 10.0 Molar

The concentration term parts per million is defined as:

a) the weight of the solute / the volume of the solution) x 10 6.

b) (the weight of the solute / the weight of the solution) x 10 6
c) (weight of the solute / liters of solution)

A solution was prepared by diluting 10.0 mL of 1.00 x 10 -3 molar solution of

potassium dichromate to 100.0 mL. What is the concentration of chromium in the
new solution?

a) 10.4 ppm Chromium

b) 104 ppm Chromium
c) 5.20 ppm Chromium

Harris, Exploring Chemical Analysis 4e Chapter 02

What are the three essential attributes of a laboratory notebook?

a)
1. Record what you did.Write in complete sentences.
2. The notebook should be understandable by a stranger.
b)
1. Record what you did.
2. Record what you observed.
3. Always write balanced equations.
c)
1. Record what you did.
2. Record what you observed.
3. The notebook should be understandable by a stranger.

The proper use of a buret involves:

a) Reading the bottom of the meniscus in a manner that avoids a parallax error
making sure that you understand that the buret reads from 50.00 mL at the top to
0.00 mL at the bottom.
b) Reading the bottom of the meniscus in a manner that avoids a parallax error
making sure that you understand that the buret reads from 0.00 mL at the top to
50.00 mL at the bottom.
c) Reading the top of the meniscus closest to the volume mark on the buret with
your eye at the same height as the top of the liquid.

A chemist is planning to use a transfer pipet to transfer 10.0 mL of a liquid from

one flask to another. The pipet is labeled TD. Which of the following would be the
correct procedure?

a)
1. Use a pipet bulb to raise the liquid above the 10.0 mL mark on the pipet.
2. Rapidly place your thumb or finger over the top of the pipet to contain the liquid.
3. Allow the liquid level to drain to the mark.
4. Allow the liquid to drain into the receiving flask.
5. Use the pipet bulb to blow any liquid remaining in the pipet into the receiving
flask.
b)
1. Use a pipet bulb to raise the liquid above the 10.0 mL mark on the pipet.
2. Rapidly place your thumb or finger over the top of the pipet to contain the liquid.
3. Release the pressure to allow the liquid level to drain to the mark.
4. Allow the liquid to drain into the receiving flask.
c)
1. Use a pipet bulb to raise the liquid above the 10.0 mL mark on the pipet.
2. Rapidly place your thumb or finger over the top of the pipet to contain the liquid.
3. Release the pressure to allow the liquid level to drain to the mark.
4. Allow the liquid to drain into the receiving flask.
5. Stop the flow of liquid at the 10.0 mL line by applying pressure over the top with
your thumb or forefinger.

For very precise work, a chemist may want to calibrate the pipets used for an
analysis. This was done by pipeting from a 20-mL pipet 20.0012 grams of water at
22°C into a weighing bottle. What is the actual volume of the pipet? The following
data is available from Table 2-4 in your text. At 22°C the correction factor based on
the density of water and buoyancy is 1.0033 mL/g.

a) 20.067 mL
b) 19.935 mL
c) 20.0672 mL

Which of the following statements is true regarding the preparation of a sample for
analysis?

a) The sample is often dried at 110°C for one hour to remove surface absorbed
water.
b) To analyze elements such as N, P, halogens, and metal in an organic compound,
a flux consisting of lithium tetraborate and sodium hydroxide is often used.
c) To analyze for gold, the sample would be treated with a mixture of hydrochloric
acid and nitric acid.

Safety is a major issue in the laboratory. Laboratory workers must wear protective
glasses at all times. Food and chemicals don't mix. Protect your body with long
pants and a lab coat if possible. Never wear sandals to a lab. Protect your feet from
spills with real shoes. If you happen to have an accident, such as spilling a chemical
on your body,

a)
1. Don't panic.
2. Get help immediately.
3. Notify your laboratory instructor.
 b)
1. Don't panic.
2. Get help immediately.
3. Notify your laboratory instructor.
4.Wash the area with a mild detergent and water.
c)
1. Don't panic.
2. Get help immediately.
3. Notify your laboratory instructor.
4. Wash the area with a mild detergent and water.
5. Remove contaminated clothing if necessary.
6. Get medical attention.

Although not often an issue, you should be aware that the buoyancy of air will
cause an object to appear lighter than its actual mass. This loss in weight will be
equal to the mass of air the object displaces. This is exactly analogous to placing an
object under water. A diver can lift masses much heavier than would be possible on
land. Using equation 2-2 in your textbook,

An organic liquid with a density of 0.935 g/cm3 weighed 2.7856 g. The balance was
equipped with stainless steel weights that have a density of 8.00 g/cm3. What is
the correct mass of the sample?

a) 2.7888 g
b) 1.0011
c) 2.7834 g

A chemist needs to accurately transfer 0.100 mL of liquid from one container to

another. Which of the following devices should be used?
a) A transfer pipet.
b) A measuring pipet.
c) A micropipet.

Which of the following statements is not correct?

a) The precipitate is a solid that forms in the mother liquor.

b) When a precipitate is formed, the mother liquor passes through the filter and
becomes the filtrate.
c) The filtrate contains the precipitate which can be dried and weighed.

Which of the following pairs do not belong together?

a) mortar and pestle

b) hygroscopic and water
c) meniscus and tare

Harris, Exploring Chemical Analysis 4e Chapter 03

How many significant figures are in the number 6.230 x 10 23?

a) 4
b) 3
c) 23

How many significant figures are in the number 0.000120?

a) 7
b) 3
c) 2
Write the answer to the following calculation to the proper number of significant
figures. 3.86 + 9.1 - 0.231 = 12.7290

a) 12.7
b) 12.73
c) 12

Write the answer to the following calculation to the proper number of significant
figures. 145.68 X 1.09 ÷ 87,000 = 11,627.6697

(a) 12,000
(b) 11,600
(c) 11,000

Define the term precision.

a) Precision refers to how close a measured value is to the "true" value.

b) Precision refers to how accurately a given measurement is made.
c) Precision is a measure of the reproducibility of a result.

Find the absolute uncertainty of the following calculation, and express the answer
to the proper number of significant figures. 12.34(±0.04) + 178.1(±0.2) -
18.493(±0.002) = 172.010

a) 172.01(± 0.2)
b) 172.0(±0.2)
c) 172.010(±0.242)

Find the absolute uncertainty of the following calculation: 3.78(±0.04) x

6.23(±0.03) x 1023 = 2.3549 x 1024 and round the answer to the proper number of
significant figures.

a) 2.3(±0.1) x 1024
b) 2.35(±0.01) x 1024
c) 2.35(±0.03) x 1024

Write the antilog of 4.278 showing the proper number of significant figures.

a) 0.6310
b) 1.897 X 104
c) 1.90 X 104

A systematic error:

a) can be discovered and corrected.

b) rises from the limitations on the ability to make a physical measurement.
c) is also known as an indeterminate error.

Express the molecular weight of K2Cr2O7 the correct number of significant figures
and find its uncertainty.

a) 294.185(± 0.004)
b) 294.185(± 0.001)
c) 294.184600(±0.000008)

Harris, Exploring Chemical Analysis 4e Chapter 04

When an analytical chemist uses the word precision when referring to the data
obtained from an analysis, the chemist is talking about:
 a) how close the mean obtained from a set of data is to the true value of the
composition of the sample analyzed.
b) relative error calculated from the mean of a set of data.
c) how close the individual data points obtained from a set of data are to each
other.

A government chemist has performed a gravimetric analysis for chloride ion on a

sample submitted to the laboratory. The following results were obtained:

Sample no. Percent chloride ion

1 27.46

2 27.52

3 27.48

4 27.10

When reporting the standard deviation, the analyst said that:

a) approximately 68.3% of the data points lie between 27.19 and 27.59 percent
chloride.
b) approximately 75% of the data points lie between 27.46 and 27.52 percent
chloride.
c) approximately 68.3% of the data points lie between 27.29 and 27.49 percent
chloride.

A government chemist has performed a gravimetric analysis for chloride ion on a

sample submitted to the laboratory. The following results were obtained:

Sample no. Percent chloride ion

1 27.46

2 27.52

3 27.48
4 27.10

Given the following data,

Degrees of freedom 98% confidence level

1 31.821

2 6.965

3 4.541

4 3.747

5 3.365
What is the 98% confidence interval for this set of data?

a) 0.37%
b) 0.91%
c) 0.45%

A student was presented with a sample of vinegar for analysis. After analyzing the
sample four times, the student was faced with the following set of data.

Given the following values of Q for rejection of data, which decision is appropriate?

a) Reject the value 4.06%.

b) No values may be rejected.
c) Reject the value 4.39%.

The following data was collected when performing a spectrophotometric analysis for
cobalt.

Using the least squares method of linear regression, the following equation was
determined to define the line generated by plotting concentration vs absorbance. Y
= 0.0196X - 0.008.

a) This equation represents the statistical best fit of a line drawn through the data
points.
b) The amount of unknown in the sample may be determined by substituting the
absorbance value of the unknown for X in the equation and solving for the Y value.
c) The value 0.0196 represents the value on the Y axis where the line crosses this
axis.

The following data was collected when performing a spectrophotometric analysis for
cobalt.

Using the least squares method of linear regression, the following equation was
determined to define the line generated by plotting concentration vs absorbance. Y
= 0.0196X - 0.008. The concentration of Cobalt in the sample was found to be:
a) 13.11 mg Co/L
b) 2.81 mg Co/L
c) 13.93 mg Co/L

If one has a Gaussian distribution of data points:

a) approximately two thirds of the data points lie above the mean, and one third of
the data points lie below the mean, accounting for all of the data points.
b) approximately 2/3 of the data points lie within plus or minus two standard
deviations of the mean.
c) Approximately 2/3 of the data points lie within plus or minus one standard
deviation of the mean.

A Gaussian distribution of data is symmetric if:

a) 4.5% of measurements lie outside the range defined by 2 standard deviations

above the mean, and two standard deviations below the mean.
b) 4.5% of measurements lie outside the range defined by 2 standard deviations
above the mean, and two standard deviations below the mean with 2.25% of the
values above 2 standard deviations from the mean and 2.25% of the values below
2 standard deviations from the mean.
c) 68.3% of the measurements lie within plus or minus one standard deviation
from the mean.

When analyzing iron content of a well drilled for use in a new housing development,
water from the well was analyzed on three different days. The following data was
obtained.
The pooled estimate of the standard deviation of the analysis is:

a) 0.14 mg Fe/L
b) 0.072 mg Fe/L
c) 0.076 mg Fe/L

The degrees of freedom used to calculate the confidence interval are:

a) the number of data points which are being evaluated.

b) the number of data points - 1.
c) The value associated with the number of data points used to determine the
value of t.

Harris, Exploring Chemical Analysis 4e Chapter 06

The end point of a titration is defined as:

a) the same as the equivalence point.

b) the actual measured volume of titrant required to complete a titration.
c) the volume associated with actual stoichiometric quantity of titrant required to
complete a titration.

In the following reaction: CaCO3 + 2HNO3 (r) Ca(NO3)2 + CO2 + H2O how many mL
of 0.1015 molar HNO3 are required to react with 0.9857 grams of CaCO 3?

a) 0.1940 mL
b) 97.04 mL
c) 194.1 mL

Iron in the +2 oxidation state reacts with potassium dichromate to produce Fe 3+

and Cr3+ according to the equation: 6 Fe2+ + Cr2O72- + 14 H+ (r) 6 Fe3+ + 2 Cr3+ + 7
H2O How many milliliters of 0.1658 molar K2Cr2O7 are required to titrate 200.0 mL
of 0.2500 molar Fe2+ solution?

a) 50.26 mL
b) 301.6 mL
c) 8.290 mL

A solution containing chloride ion was analyzed by the Volhard method. A 50.00 mL
sample containing chloride ion was treated with 25.00 mL of 0.2500 molar silver
nitrate. The precipitated AgCl removed from the solution by filtration and 1.00 mL
of 0.1000 molar Fe3+ was added to the filtrate. This new solution was then titrated
with 10.67 mL of 0.2380 M KSCN. What is the concentration of chloride ion in the
original solution?

a) 0.0742 M chloride ion

b) 0.1250 M chloride ion
c) 3.710 M chloride ion

Potassium permanganate solutions may be standardized by titrating against

primary standard sodium oxalate. 2MnO41- + 5C2O42- + 16H+ (r) 2Mn2+ + 10CO2 +
8H2O What is the molarity of the KMnO4 solution if 43.80 mL of the KMnO4 is
required to titrate 0.2168 grams of Na 2C2O4?

a) 0.01478 M KMnO4
b) 0.03694 M KMnO4
c) 0.09235 M KMnO4
The mathematical equation which represents the solubility product when the
insoluble compound Mn2S3 is dissolved in water is:

a) [Mn3+] [S2-] = Ksp

b) [Mn3+]3 [S2-]2 = Ksp
c) [Mn3+]2 [S2-]3 = Ksp

Given that the solubility product for La(IO3)3 is 1.0 x 10-11, what is the concentration
of La3+ in a saturated solution of lanthanum iodate.

a) 7.8 x 10-4 moles/liter

b) 1.0 x 10-3 moles/liter
c) 7.18 x 10-5 moles/liter

If a 0.100 molar solution of NaOH is added to a solution containing 0. 200 molar

Ni2+, 0.200 molar Ce3+, and 0.200 molar Cu2+, which metal hydroxide will
precipitate first? Ksp Ni(OH)2 = 6.0 x 10-16, Ksp Ce(OH)3 = 6.0 X 10-22, Ksp Cu(OH)2
= 4.8 x 10-20

a) Ni(OH)2
b) Ce(OH)3
c) Cu(OH)2

What is the lead concentration of a saturated solution of lead(II) sulfate containing

0.020 molar Na2SO4 ? Ksp PbSO4 = 6.3 x 10-7

a) 7.9 x 10-4 M
b) 5.6 x 10-3 M
c) 3.2 x 10-5 M

A beaker contains 250.0 mL of 0.150 molar silver ion (Ag +). To this beaker is added
250.0 mL of 0.300 molar bromide ion (Br-). What is the concentration of Ag+ in the
final solution? Ksp AgBr = 5.0 x 10-13

a) 7.1 x 10-7 M
b) 6.7 x 10-12 M
c) 3.3 x 10-12 M

Harris, Exploring Chemical Analysis 4e Chapter 07

When performing a gravimetric analysis in which a product is precipitated, isolated,
and weighed, coprecipitation is a constant concern. Coprecipitation involves:

a) the precipitation of two insoluble substances simultaneously from the same

solution.
b) the precipitation of a normally soluble material with an insoluble material.
c) The failure to separate two insoluble materials because the most soluble
material begins to precipitate before the most insoluble material has been removed
from the solution.

To obtain a precipitate which is useful for gravimetric analysis, the analyst tries to
obtain conditions to encourage crystal growth, as opposed to the formation of a
colloid. Which of the following statements aids in the formation of a crystalline
precipitate?

a) The solution is kept cool to slow down the movement of ions to allow crystals to
form.
b) The solutions are made as dilute as practical to allow crystals to form slowly.
c) The solutions are mixed rapidly to allow the appropriate ions to make contact
without interference of other materials.

Which of the following processes is true regarding the digestion of a solution

containing a precipitate?

a) Digestion tends to increase particle size of the precipitate.

 b) Digestion is used to slow down the coagulation of a colloidal precipitate because
of the increased energy added to the solution.
c) A long digestion is not recommended because the higher temperatures enable
impurities to become trapped in the crystal lattice of the precipitate.

In the gravimetric analysis of iron, hydroxide may be added to a solution containing

Fe3+ to precipitate a gelatinous mess that is ignited to form Fe 2O3. If 0.2864 grams
of Fe2O3 were formed from the ignition of the precipitated mess, how many grams
of FeCO3 were contained in the original sample analyzed?

a) 0.4155 g FeCO3
b) The answer cannot be computed because the sample did not contain any Fe 2+.
c) 0.2078 g FeCO3

The chloride content of a sample may be analyzed gravimetrically by adding a

solution of silver nitrate to a solution containing chloride ion. The analyst typically
assumes that the sample is pure NaCl to determine the quantity of silver nitrate
needed for the precipitation. If an analyst dissolved a 0.2681 gram sample
containing chloride ion in a dilute nitric acid solution, how many mL of 0.20 molar
silver nitrate should be added to the chloride solution to completely precipitate all of
the chloride ion?

a) 0.90 mL
b) 23 mL
c) 38 mL

In the combustion of phthalic acid (C6H4(COOH)2), how many moles of water are
produced per mole of phthalic acid burned?

a) 6 mol H2O
b) 3 mol H2O
c) 4 mol H2O
When a 0.460 gram sample of a compound containing carbon, hydrogen, and
oxygen was burned in a stream of pure oxygen, 0.880 grams of CO 2 and 0.540 g of
H2O was produced. What is the simplest whole number ratio of the elements
present in the compound?

a) CH3O
b) C2H2
c) C2H6O

A sample contains 0.2784 grams of sodium chloride (NaCl) and 0.5486 grams of
magnesium chloride (MgCl2). The chloride in the sample was precipitated by the
addition of 47.8 mL of a silver nitrate solution. What is the concentration of the
silver nitrate solution?

a) 0.341M AgNO3
b) 0.220 M AgNO3
c) 0.00341 M AgNO3

A sample of ore containing manganese weighed 1.2354 grams. This sample was
heated in a solution of nitric acid, which dissolved the manganese ion producing
manganese(III) nitrate (Mn(NO3)3). The acidity of the solution was adjusted, and
Hydrogen sulfide gas was bubbled into the solution producing 0.2876 grams of
manganese(III) sulfide (Mn2S3). What is the percentage of manganese in the
original sample?

a) 12.37% Mn
b) 6.19% Mn
c) 3.09% Mn

A sample containing Al2O3 and Na2Cr2O7. 2H2O was brought into the laboratory for
analysis. The analyst heated a 2.2846 gram sample of this material to 100 oC for
one hour, at which time only Al2O3 and Na2Cr2O7 remained. This mixture was found
to weigh 2.2312 grams. Calculate the percent chromium in the sample.

a) 6.750% Cr
b) 13.50% Cr
c) 16.97 % Cr

Harris, Exploring Chemical Analysis 4e Chapter 08

In the following reaction, identify the conjugate acid-base pair. NO 2- + H2O

HNO2 + OH-

a) NO2- , OH-
b) NO2- , H2O
c) NO2- , HNO2

A solution was found to contain 8.26 x 10-4 molar NaOH. Calculate the pH of the
solution.

a) 3.08
b) 10.9
c) 1.00

A solution of sodium sulfate was found to have a pNa of 5.83. What is the sulfate
concentration of the solution?

a) 7.40 x 10-7 M
b) 1.48 x 10-6 M
c) 7.66 x 10-1 M

Calculate the hydrogen ion concentration of a 0.100 molar solution of chloroacetic

acid. Ka for chloroacetic acid = 1.36 x 10-3.
a) 0.0117 M
b) 0.0369 M
c) 7.39 x 10-12 M

Calculate the hydrogen ion concentration of a 0.100 molar solution of methyl

amine. Ka for methyl amine hydrochloride = 2.3 X 10 -11.

a) 1.5 x 10-6 M
b) 6.9 x 10-3 M
c) 1.4 x 10-12 M

Calculate the pH of a 0.100 molar solution of sodium chloroacetate. Ka for

chloroacetic acid = 1.36 x 10-3

a) 1.17 x 10-8
b) 7.93
c) 1.93

Calculate the pH of a 0.05 molar solution of iodic acid. Ka for iodic acid = 0.17.

a) 1.39
b) 1.03
c) 13.0

A 0.100 molar solution of nitrous acid (HNO2) had a pH of 2.07. What is the Ka
value for nitrous acid.

a) 7.24 x 10-4
b) 7.24 x 10-5
c) 8.51 x 10-2

Find the concentration of phenol and phenolate ion in a 0.0100 molar solution of
phenol. Ka for phenol = 1.05 x 10-10

a) 1.02 X 10-6 M phenol, 1.02 x 10-6 M phenolate ion

b) 1.02 X 10-6 M phenol , 1.00 x 10-2 M phenolate ion
c) 1.00 X 10-2 M phenol, 1.02 X 10-6 M phenolate ion

Find the fraction of association of a 0.100 molar solution of hydrazoic acid. Ka for
hydrazoic acid = 2.20 x 10-5.

a) 98.6%
b) 1.45%
c) 0.40%

Harris, Exploring Chemical Analysis 4e Chapter 09

Which of the following pairs of compounds and ions could be used to form a buffer
solution?

a) 0.10 M HClaq and 0.10 M NaCl

b) 0.10 M NH4Cl and 0.10 M NH3
c) 0.10 M HNO2 and 1.0 x 10-4 M NaNO2

Which of the combination of ions and molecules may produce a buffer solution in an
aqueous environment.

a) 50.00 mL of 0.100 M NaOH and 50.00 mL of 0.100 M CH 3COOH.

b) 50.00 mL of 0.100 M HNO3 and 50.00 mL of 0.100 M CH3COOH.
c) 50.0 mL of 0.050 M HNO3 and 50.0 mL of 0.100 M CH3COONa.
Calculate the ratio of ethyl amine (CH3CH2NH2) to the ethyl ammonium ion
(CH3CH2NH3+) in a solution with a pH of 11.0. pKa for CH 3CH2NH3+ = 10.636.

a) 2.31
b) 10.81
c) 0.432

A buffer solution was prepared by mixing 50.0 mL of a 0.100 molar solution of

CH3COOH with 0.500 grams of NaCH3COO. The resulting mixture is diluted to 100.0
mL. What is the pH of the solution? Ka for acetic acid is 1.75 x 10 -5.

a) 4.84
b) 7.67
c) 4.97

How many grams of NaCH3COO must be added to 150.0 mL of a 0.150 M solution

of CH3COOH to produce a buffer pH 4.75? Assume that the volume will remain
constant. pKa for CH3COOH = 4.757

a) 0.147 M
b) 12.1 grams
c) 1.81 grams

A buffer solution was prepared by dissolving 5.00 grams of sodium propanate

(NaCH3CH2CO2) in a solution containing 0.100 moles of propanoic acid
(CH3CH2CO2H) and diluting the mixture to 500.0 mL. To this solution was added
5.00mL of 1.00 M HCl. Calculate the pH of the resulting solution. pKa for propanoic
acid is 4.874.

a) 4.65
b) 4.62
c) 4.52

A beaker containing 500.0 mL was determined to contain 0.150 M ammonia (NH 3)

and 0.150 M ammonium chloride NH4Cl. To this solution was added 50.0 mL of 0.15
M hydrochloric acid (HCl). What was the change in pH of the ammonia, ammonium
ion solution? pKa for NH4+ = 9.244

a) The pH of the solution will go down 0.087 pH units.

b) The pH of the solution will go up 0.13 pH units.
c) The pH of the solution will go up 0.087 pH units.

How many mL of 0.100 M HCl should be added to 500.0 mL of 0.150 M sodium

acetate (NaCH3CO2) to produce a buffer pH 5.0? pKa acetic acid = 4.757.

a) 273 mL
b) 1000 mL
c) 476 mL

Using the acid dissociation constant table in your textbook, which buffer system will
give the greatest buffer capacity at pH 5.0?

a) Chlorous acid / chlorite ion

b) Hydrogen cyanide / cyanide ion
c) Propanoic acid /propanate ion

How many grams of sodium hydroxide (NaOH) must be added to 1.50 L of a 0.400
molar solution of oxoacetic acid (HCOCO2H) to produce a buffer pH 4.00? pKa for
oxoacetic acid = 3.46

a) 18.67 grams
b) 0.47 grams
c) 5.33 grams

Harris, Exploring Chemical Analysis 4e Chapter 10

A solution containing 75.0 mL of 0.150 M strong acid (HCl), is titrated with 75.0 mL
of 0.300 M strong base (NaOH). What is the pH of the resulting solution?

a) 7.00
b) 13.2
c) 12.9

Consider the titration of 25.0 mL of 0.150 M HBr with 0.0750 M NaOH. What is the
volume of NaOH required to reach the equivalence point.

a) 25.0 mL
b) 50.0 mL
c) 12.5 mL

A solution containing 50.0 mL of 0.1500 M C2H3COOH is titrated with 0.1500 M

NaOH. What is the pH of the solution after the addition of 25.0 mL of NaOH? pKa
for C2H3COOH is 4.76.

a) 4.76
b) 9.24
c) 1.30

When an ant bites you, the reason it stings is because of an injection of formic acid.
What is the pH when 50.0 mL of 0.1480 M formic acid (HCOOH) is titrated with
40.2 mL of 0.1841 M NaOH? PKa formic acid = 3.745.

a) 2.42
b) 11.6
c) 11.7

In a titration, 48.6 mL of 0.1280 M KOH is added to 45.0 mL of 0.1200 M

hydroxyacetic (HOCH2CO2H) acid. Calculate the pH of the solution. pKa for
HOCH2CO2H = 3.831.

a) 2.06
b) 2.38
c) 11.94

In a titration, 25.0 mL of 0.154 M nitric acid (HNO 3) was added to 45.0 mL of 0.213
M ammonia (NH3). What is the pH at this point? PKa NH3 = 9.244

a) 9.42
b) 4.58
c) 9.07

The weak base trimethyl amine ((CH3)3N) was titrated with hydrochloric acid (HCl).
The titration required 25.3 mL of 0.150 molar HCl to react with 35.15 mL of 0.108
molar trimethyl amine. What is the pH of the solution? pKa for (CH 3)3N = 9.80

a) 5.50
b) 2.70
c) 8.50

A titration was performed by adding 35.85 mL of 0.1350 molar nitric acid (HNO 3) to
55.80 mL of 0.08673 molar potassium hydroxide (KOH). What is the pH of the
solution?

a) 1.28
b) 7.00
c) 3.28

25.0 mL of 0.100 molar triethyl amine ((CH3CH2)3N) is titrated with 0.0500 molar
hydrochloric acid (HCl). The following data was obtained:

What is pKa for the triethylammonium ion?

a) 11.86
b) 10.71
c) 6.79

A flask containing 36.8 mL of 0.138 molar sodium acetate (NaC 2H3O2) is titrated
with 24.9 mL of 0.128 molar nitric acid (HNO 3). Calculate the pH of the solution.
pKa for acetic acid = 4.757

a) 4.53
b) 9.47
c) 4.98