D 6813 - 02 - Rdy4mtmtmdi

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
An American National Standard

Designation: D 6813 – 02
Standard Guide for

Performance Evaluation of Hydraulic Fluids for Piston
Pumps1
This standard is issued under the fixed designation D 6813; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope Bituminous Materials by Distillation2

1.1 This guide establishes test protocols and methodologies D 97 Test Method for Pour Point of Petroleum Products2
for determining the suitability of fluids for use in fluid power D 130 Test Method for Detection of Copper Corrosion from
systems that incorporate axial or radial piston pumps. The Petroleum Products by the Copper Strip Tarnish Test2
suitability of all fluid types to meet specific levels of perfor- D 445 Test Method for Kinematic Viscosity of Transparent
mance in piston pumps is addressed. These fluids include, but and Opaque Liquids2
are not limited to formulations based on mineral, synthetic or D 482 Test Method for Ash from Petroleum Products2
vegetable oil base stocks. The finished fluids may be in the D 611 Test Methods for Aniline Point and Mixed Aniline
form of straight oils, soluble oils or invert emulsions. Point of Petroleum Products and Hydrocarbon Solvents2
1.2 The test protocols and methodologies described in this D 664 Test Method for Acid Number of Petroleum Products
guide have been selected for their ability to distinguish by Potentiometric Titration2
between highly acceptable, acceptable and unacceptable fluid D 665 Test Method for Rust-Preventing Characteristics of
performance in piston pumps. They take into account the broad Inhibited Mineral Oil in the Presence of Water2
range of operating conditions piston pumps are subjected to, as D 874 Test Method for Sulfated Ash from Lubricating Oils
well as the common variations in design and materials of and Additives2
construction among pump manufacturers. D 877 Test Method for Dielectric Breakdown Voltage of
1.3 This guide is intended to complement proprietary test Insulating Liquids Using Disk Electrodes3
protocols and methodologies employed by some piston pump D 892 Test Method for Foaming Characteristics of Lubri-
manufacturers. The test protocols and methodologies within cating Oils2
this guide may help pump manufacturers, fluid formulators and D 943 Test Method for Oxidation Characteristics of Inhib-
end users accurately screen potential fluids for specific perfor- ited Mineral Oils2
mance characteristics. The results of this screening may be D 974 Test Method for Acid and Base Number by Color-
sufficient in certain instances for pump manufacturers to forego Indicator Titration2
requirements for additional fluid performance tests. D 1121 Test Method for Reserve Alkalinity of Engine
1.4 This standard does not purport to address all of the Coolants and Antirusts4
safety concerns, if any, associated with its use. It is the D 1123 Test Methods for Water in Engine Coolant Concen-
responsibility of the user of this standard to establish appro- trate by the Karl Fischer Reagent Method4
priate safety and health practices and determine the applica- D 1169 Test Method for Specific Resistance (Resistivity) of
bility of regulatory requirements prior to use. Electrical Insulating Liquids3
D 1298 Test Method for Density, Relative Density (Specific
2. Referenced Documents Gravity), or API Gravity of Crude Petroleum and Liquid
2.1 ASTM Standards: Petroleum Products by Hydrometer Method2
D 92 Test Method for Flash and Fire Points by Cleveland D 1401 Test Method for Water Separability of Petroleum
Open Cup2 Oils and Synthetic Fluids2
D 93 Test Methods for Flash-Point by Pensky-Martens D 1500 Test Method for ASTM Color of Petroleum Prod-
Closed Cup Tester2 ucts (ASTM Color Scale)2
D 95 Test Method for Water in Petroleum Products and D 1533 Test Method for Water in Insulating Liquids by
Coulometric Karl Fischer Titration3
D 2070 Test Method for Thermal Stability of Hydraulic
1
This guide is under the jurisdiction of ASTM Committee D02 on Petroleum Oils2
Products and Lubricants and is the direct responsibility of Subcommittee D02.N0.07
on Lubricating Properties.
3
Current edition approved June 10, 2002. Published October 2002. Annual Book of ASTM Standards, Vol 10.03.
2 4
Annual Book of ASTM Standards, Vol 05.01. Annual Book of ASTM Standards, Vol 15.05.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
D 6813 – 02
D 2270 Practice for Calculating Viscosity Index from Kine- D 6158 Specification for Mineral Hydraulic Oils6
matic Viscosity at 40 and 100°C2 D 6304 Test Method for Determination of Water in Petro-
D 2272 Test Method for Oxidation Stability of Steam Tur- leum Products, Lubricating Oils, and Additives by Coulo-
bine Oils by Rotating Pressure Vessel2 metric Karl Fischer Titration6
D 2273 Test Method for Trace Sediment in Lubricating D 6376 Test Method for Determination of Trace Metals in
Oils2 Petroleum Coke by Wavelength Dispersive X-Ray Fluo-
D 2422 Classification of Industrial Fluid Lubricants by rescence Spectroscopy7
Viscosity System2
D 6546 Test Methods for and Suggested Limits for Deter-
D 2619 Test Method for Hydrolytic Stability of Hydraulic
mining Compatibility of Elastomer Seals for Industrial
Fluids (Beverage Bottle Method)2
Hydraulic Fluid Applications7
D 2624 Test Methods for Electrical Conductivity of Avia-
tion and Distillate Fuels2 D 6547 Test Method for Corrosiveness of a Lubricating
D 2717 Test Method for Thermal Conductivity of Liquids2 Fluid to a Bimetallic Couple7
D 2766 Test Method for Specific Heat of Liquids and D 6595 Test Method for Determination of Wear Metals and
Solids2 Contaminants in Used Lubricating Oils or Used Hydraulic
D 2783 Test Method for Extreme-Pressure Properties of Fluids by Rotating Disc Electrode Atomic Emission Spec-
Lubricating Fluids (Four-Ball Method)2 trometry7
D 2879 Test Method for Vapor Pressure-Temperature Rela- E 70 Test Method for pH of Aqueous Solutions With the
tionship and Initial Decomposition Temperature of Liquids Glass Electrode4
by Isoteniscope2 E 203 Test Method for Water Using Volumetric Karl Fischer
D 2882 Test Method for Indicating Wear Characteristics of Titration4
Petroleum and Non-Petroleum Hydraulic Fluids in Con- E 659 Test Method for Autoignition Temperature of Liquid
stant Volume Vane Pump2 Chemicals8
D 2983 Test Method for Low-Temperature Viscosity of F 312 Test Methods for Microscopical Sizing and Counting
Automotive Fluid Lubricants Measured by Brookfield Particles from Aerospace Fluids on Membrane Filters8
Viscometer2
2.2 AFNOR Standards:9
D 3427 Test Method for Air Release Properties of Petro-
leum Oils5 AFNOR NF E48-690 Hydraulic Fluid Power. Fluids. Mea-
D 4052 Test Method for Density and Relative Density of surement of Filterability of Mineral Oils
Liquids by Digital Density Meter5 AFNOR NF E48-691 Hydraulic Fluid Power. Fluids. Mea-
D 4172 Test Method for Wear Preventive Characteristics of surement of Filterability of Minerals Oils in the Presence
Lubricating Fluid (Four-Ball Method)5 of Water
D 4293 Specification for Phosphate Ester Based Fluids for AFNOR NF E48-692 Hydraulic Fluid Power. Fluids. Mea-
Turbine Lubrication5 surement of Filterability of HFC and HFD Class Fire
D 4308 Test Method for Electrical Conductivity of Liquid Resistant Fluids
Hydrocarbons by Precision Meter5 2.3 ANSI (NFPA) Standards:10
D 4310 Test Method for Determination of the Sludging and ANSI/(NFPA) Standard T2.13.7R1-1996 Hydraulic Fluid
Corrosion Tendencies of Inhibited Mineral Oils5 Power—Petroleum Fluids—Prediction of Bulk Moduli
D 5182 Test Method for Evaluating the Scuffing Load
ANSI/Standard NFPA/JIC T2.24.1-1990 Hydraulic Fluid
Capacity of Oils (FZG Visual Method)5
Power—Systems Standard for Stationary Industrial Ma-
D 5185 Test Method for Determination of Additive Ele-
chinery
ments, Wear Metals, and Contaminants in Used Lubricat-
ing Oils and Determination of Selected Elements in Base ANSI/(NFPA) Standard T3.9.20-1992 Hydraulic Fluid
Oils by Inductively Coupled Plasma Atomic Emission Power—Pumps—Method of Testing and Presenting Basic
Spectrometry (ICP-AES)5 Performance Data for Pressure Compensated Pumps
D 5534 Test Method for Vapor-Phase Rust-Preventing ANSI/(NFPA) Standard T3.9.33-1997 Hydraulic Fluid
Characteristics of Hydraulic Fluids6 Power—Pumps—Method of Testing and Presenting Basic
D 5621 Test Method for Sonic Shear Stability of Hydraulic Performance Data for Load Sensing Pumps
Fluid6 ANSI/(NFPA) Standard T3.16.2-R1-1997 Hydraulic Fluid
D 6006 Guide for Assessing Biodegradability of Hydraulic Power—Design for Nonintegral Industrial Reservoirs
Fluids6 2.4 CETOP Standard:
D 6046 Classification of Hydraulic Fluids for Environmen-
tal Impact6
D 6080 Practice for Defining the Viscosity Characteristics
of Hydraulic Fluids6 7
Annual Book of ASTM Standards, Vol 05.04.
8
Annual Book of ASTM Standards, Vol 14.02.
9
Available from AFNOR, Administration des Ventes, 11, avenue Francis de
Pressensi, 93571 Saint-Denis La Plaine Cedex.
5 10
Annual Book of ASTM Standards, Vol 05.02. Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
6
Annual Book of ASTM Standards, Vol 05.03. 4th Floor, New York, NY 10036.
2
D 6813 – 02
CETOP RP 67H Antiwear Vane Pump Test for Hydraulic ISO 11171 Hydraulic Fluid Power—Calibration of Auto-
Fluids11 matic Particle Counters for Liquids
2.5 DIN Standards:12 ISO 12922 Lubricants, Industrial Oils and Related Products
DIN 51348 Testing of Fire Resistant Governor Fluids; (Class L)—Family H (Hydraulic Systems)—
Determination of Hydrolytic Stability Specifications for Categories HFAE, HFAS, HFB, HFC,
DIN 51373 Testing of Fire Resistant Governor Fluids; HFDR and HFDU
Determination of Oxidative Stability Including Evaluation ISO 13357-2 Part 2: Petroleum Products—Determination of
of Catalyst Plates the Filterability of Lubricating Oils—Part 2: Procedure for
DIN 51389/2 Determination of Lubricants; Mechanical Dry Oils
Testing of Hydraulic Fluids in the Vane-Cell-Pump; ISO 14935 Petroleum and Related Products—
Method A for Anhydrous Hydraulic Fluids Determination of Wick Flame Persistence of Fire-
DIN 51389/3 Determination of Lubricants; Mechanical Resistant Fluids
Testing of Hydraulic Fluids in the Vane-Cell-Pump—Part ISO 15029 Petroleum and Related Products—
3: Method B for Aqueous Not Easily Inflammable Hy- Determination of Spray Ignition Characteristics of Fire-
draulic Fluids Resistant Fluids—Part I: Spray Flame Persistence—
DIN 51515, Part 1 Lubricants and Governor Fluids for Hollow Cone Nozzle Method
Steam Turbines; L-TD Lubricating Oils and Governor 2.8 LUX Standard:15
Oils; Minimum Requirements LUX 5.9 Determination of the Corrosion Inhibiting Proper-
DIN 51554, Part 3 Testing of Mineral Oils; Test of Suscep- ties of Fluids, Requirements for Tests Applicable to
tibility to Aging According to Baader; Testing at 95°C Fire-Resistant Fluids Used for Power Transmission and
2.6 British Standard:13 Control (Hydrostatic and Hydrokinetic), April, 1994
IP 281 Determination of Anti-Wear Properties of Hydraulic 2.9 SAE Standards:16
Fluids—Vane Pump Method SAE J745 Surface Vehicle Recommended Practice, Hydrau-
2.7 ISO Standards:14 lic Power Pump Test Procedure
ISO 4021 Hydraulic Fluid Power—Particulate Contamina- SAE J1276 MAR86 Standardized Fluid for Hydraulic Com-
tion Analysis—Extraction of Fluid Samples From Lines of ponent Tests
an Operating System 3. Terminology
ISO 4402 Hydraulic Fluid Power—Calibration of
Automatic-Count Instruments for Particles Suspended in 3.1 Definitions of Terms Specific to This Standard:
Liquids—Method Using Classified AC Fine Test Dust 3.1.1 abrasive wear—wear due to hard particles, including
Contaminant wear debris or fluid contaminants, or hard protuberances forced
against and moving along a hard surface.
ISO 4404 Petroleum and Related Products—Determination
3.1.2 axial piston pump—in the axial piston pump, the
of the Corrosion Resistance of Water-Containing Fire-
pistons are positioned axially, parallel to the driveshaft, and
Resistant Fluids for Hydraulic Systems
their reciprocating motion is caused by an inclined swash plate
ISO 4406 Hydraulic Fluid Power—Fluids—Method for
as illustrated in Fig. 1.
Coding The Level of Contamination by Solid Particles
3.1.3 bent axis piston pump—in the bent axis piston pump,
ISO 4407 Hydraulic Fluid Power—Fluid Contamination—
the axis of the cylinder barrel is held at a fixed angle relative
Determination of Particulate Contamination by the Count-
to the centerline of the driveshaft as illustrated in Fig. 2.
ing Method Using a Microscope
3.1.4 biodegradable—capable of undergoing decomposi-
ISO 5884 Aerospace—Fluid Systems and Components— tion into carbon dioxide, methane, water, inorganic com-
Methods for System Sampling and Measuring the Solid pounds, or biomass in which the predominant mechanism is the
Particle Contamination of Hydraulic Fluids enzymatic action of microorganisms that can be measured by
ISO 6073 Petroleum Products—Prediction of the Bulk standardized tests, in a specific period of time, reflecting
Moduli of Petroleum Fluids Used in Hydraulic Power available disposal conditions.
Systems 3.1.5 biomass—any material, excluding fossil fuels, which
ISO 6743/4 Part 4: Family H (Hydraulic Systems), Lubri- is or was a living organism that can be used as a fuel. Peanut
cants, Industrial Oils and Related Products (Class L) : hulls, agricultural waste, corn and other grains, and sugar are
Classification Part 4: Family H (Hydraulic Systems) all examples of biomass.
3.1.6 case drainage—leakage from around piston clear-
ances and control valves to the case drain port in the pump
11
Per the CETOP website, this standard is no longer available for purchase and housing which returns fluid to the reservoir.
is officially withdrawn. Most CETOP technical documents have been replaced by
3.1.7 cycled volume—cycled volume testing subjects a hy-
ISO standards over the years (a cross-reference list is available from CETOP). This
standard will be retained pending completion of work in CEN/TC19/WG28. draulic pump or component to repeated pulses of volume flow
12
Available from Beuth Verlag GmbH (DIN-- DIN Deutsches Institut fur
Normung e.V.), Burggrafenstrasse 6, 10787, Berlin, Germany.
13 15
Available from Institute of Petroleum (IP), 61 New Cavendish St., London, Available from European Safety and Health Commission for the Mining and
WIG 7AR, U.K. Other Extractive Industries, Doc. No. 4746/10/91, EN, Luxembourg.
14 16
Available from International Organization for Standardization (ISO), 1 rue de Available from Society of Automotive Engineers (SAE), 400 Commonwealth
Varembé, Case postale 56, CH-1211, Geneva 20, Switzerland. Dr., Warrendale, PA 15096-0001.
3
D 6813 – 02
FIG. 1 Illustration of an Axial Piston Pump
3.1.12 fixed displacement—the amount of flow cannot be

varied per each shaft rotation although it can be varied by
varying the rotational speed of the shaft.
3.1.13 flow degradation—flow degradation refers to the loss
of flow through the hydraulic pump caused by lubrication wear,
cavitation erosion, or contamination wear and is expressed as
the ratio of flow rate delivered after the test to the flow rate
delivered before the test.
3.1.14 fluid residence time (turnover time)—the average
time that a given volume of fluid remains in the reservoir from
the time of entry into the reservoir from the system until it
enters the pump inlet is determined by the reservoir volume/
flow rate.
Delivery ~L/min! 3 Pressure ~kPag!
W ~Watt! 5 60 (1)
FIG. 2 Illustration of a Bent Axis Piston Pump
3.1.15 hydraulic power—the output power of a hydraulic
from a predetermined minimum to a maximum flow at a pump which is defined by:
constant pressure.
3.1.8 delivery—the flow output per unit time expressed in Delivery ~gal/min! 3 Pressure ~psig!
hp ~Horsepower! 5 1714 (2)
litres per minute (L/min) or in gallons per minute (gal/min).
3.1.9 displacement (geometrical)—the volume of hydraulic 3.1.16 inlet pressure (minimum)—the minimum inlet pres-
fluid that is transported through the hydraulic pump during a sure, specified by the pump supplier, for each set of operating
single rotation of the pump shaft and is expressed in volume parameters.
output per revolution (cm3/rev or in.3/rev). 3.1.17 leakage flow—this is related to the annular clearance
3.1.10 face plate (valve plate, port plate, lens plate)—the between the piston and the cylinder; increased clearances due
face plate, which is held at a fixed position, controls the timing to erosion and wear results in a loss of volumetric efficiency
of the inlet and outlet of the fluid flow, depending on the (see 3.1.26).
position of the cylinder barrel, during rotation of the pump. 3.1.18 leakage pressure (case drain pressure)—back-
3.1.11 filterability—a measure of the fluid’s ability to pass pressure that the case experiences during leakage which is
through filter media. determined by the size of the case drain port, hose, fluid
4
D 6813 – 02
viscosity, and the rate of leakage flow to the reservoir via the E T 5 Ev 3 Em (7)
case drain. 3.1.27 variable displacement—the amount of flow per each
3.1.19 operating pressure—the pressure at the discharge shaft revolution may be varied to limit the outlet flow to a
port of the hydraulic pump. preselected value.
3.1.20 pulsed (cycled) pressure—pulsed pressure testing
subjects a hydraulic pump or component to repeated pressure 4. Significance and Use
pulses (at a constant volume), often from close to zero 4.1 Users of hydraulic equipment which includes piston
(minimum load) to a predetermined maximum pressure, in pumps would like assurance that the fluids they use will allow
order to evaluate fatigue life or moving part interaction their systems to operate safely with reasonable equipment life.
problems and leakage. This assurance is commonly provided by the fluid supplier in
3.1.21 pump capacity (pump displacement)—the actual the form of results of standardized tests on the fluid, or
pump displacement expressed in volume per revolution (cm3/ demonstrated success in field use in similar systems, or both.
rev). This guide will help fluid developers and users develop testing
3.1.22 radial piston pump—in the radial piston pump, the protocols which demonstrate the suitability of a fluid for its
pistons are positioned radially, perpendicular to the driveshaft, intended use, including any required limitations on hydraulic
and piston motion is caused by the use of a fixed cylinder and system operating conditions.
rotating cam plate as illustrated in Fig. 3, or a rotating block 4.2 The significance and use of each test method cited in
around a stationary cam can also be used. this guide will depend upon the system in use and the purpose
3.1.23 reservoir, hydraulic—a container for the storage of a of the test method. Use the most recent editions of ASTM test
fluid used in a hydraulic system. methods.
3.1.24 shaft power—the input power driving the hydraulic
pump (often from an electric motor) which is defined by: 5. Fluid Classification
Torque ~N·m! 3 Speed ~rpm!
5.1 Mineral oil hydraulic fluids are classified in Specifica-
W ~Watt! 5 9.549 (3) tion D 6158. Fire-resistant hydraulic fluids are classified in ISO
6743/4 and the specifications for these fluid classes are
Torque ~lbf·in.! 3 Speed ~rpm!
hp ~Horsepower! 5 (4) provided in ISO 12922.
63 025
5.2 Mineral Oil Hydraulic Fluids:
3.1.25 swash plate (creep plate, wear plate, wobble 5.2.1 Type HH Hydraulic Oils—Non-inhibited refined min-
plate)—in a swash-plate (axial) piston pump, the shaft rotates eral oils for hydraulic systems that do not have specific
the piston block, thus rotating the pistons, which are held requirements of oxidation stability, rust protection, or anti-wear
against the surface of a swash plate by springs and a retainer properties. Type HH oils are usually intended for total loss
plate. For the piston pump to produce a flow, the swash plate systems or very light duty equipment.
must be held at some angle relative to the centerline of the shaft 5.2.2 Type HL Hydraulic Oils—Refined mineral oils with
and the angle will force the pistons to move in and out of the improved rust protection and oxidation stability for hydraulic
piston or cylinder barrel of the pump as shown in Fig. 1. systems where relatively high temperatures and long periods of
3.1.26 total effıciency—hydraulic pumping efficiency, or operation time are expected, and where there is the possibility
total efficiency (ET), is a combination of two efficiencies, of water or humidity that could rust metal parts of the
volumetric efficiency (Ev) and mechanical efficiency (Em) and machinery. These oils are intended for use in systems where
is determined from variable displacement. only full film lubrication is expected between the moving parts.
Actual Flow Output Usually systems working at low pressures specify HL oils.
Ev 5 Theoretical Flow Output (5) Some high-pressure piston pumps can operate satisfactorily on
Theoretical Torque Input these oils.
Em Actual Torque Output (6) 5.2.3 Type HM Hydraulic Oils—Oils of HL type with
improved anti-wear properties, for general hydraulic systems,
especially for those working at high pressure and where the
possibility of metal to metal contact exists. Type HM oils are
usually specified for hydraulic systems with vane pumps, or
when the system is intended to work at maximum pump
capacity for long periods of time.
5.2.4 Type HV Hydraulic Oils—Oils of the HM type with
improved viscosity/temperature properties, for general hydrau-
lic systems where equipment is intended to operate over a wide
range of ambient temperatures.
5.3 Fire-Resistant Hydraulic Fluids:
5.3.1 Type HFA Hydraulic Fluids—Fire-resistant hydraulic
fluids that may be further classified as:
5.3.1.1 Type HFAE Hydraulic Fluids—Mineral oil-in-water
emulsions containing less than 20 % by volume mineral oil.
FIG. 3 Schematic Illustration of a Radial Piston Pump 5.3.1.2 Type HFAS Hydraulic Fluids—Mineral oil-free
5
D 6813 – 02
aqueous synthetic polymer-thickened solutions, often micro- established by specific testing protocol. For example, some
emulsions, containing >80 % water. These fluids are suitable fire-resistant fluids of the HFC and HFD type are readily
for use at low working pressures and temperatures varying biodegradable as established by Guide D 6006, but this is not
from 5 to <55°C. reflected in the current ISO specifications. In this guide,
5.3.2 Type HFB Hydraulic Fluids—Water-in-mineral oil reference to biodegradable fluids indicates that they pass
emulsions containing <60 % mineral oil, which are used as appropriate biodegradability standards, not necessarily their
fire-resistant hydraulic fluids at operating temperatures of 5 to placement on a listing of biodegradable fluid classes.
<55°C.
5.3.3 Type HFC Hydraulic Fluids—Thickened water-glycol 6. Fluid Properties and Performance Testing Procedures
fluids containing >35 % water which are suitable for use at 6.1 The hydraulic fluid is a component of the total hydraulic
operating temperatures of -20 to <60°C. system and to be used properly, various properties of the fluid
5.3.4 Type HFD Hydraulic Fluids—Anhydrous synthetic must be considered relative to system design. These properties
fire-resistant fluids used at operating temperatures of <120°C. are determined by various tests procedures which include:
Type HFD fluids are further subdivided into Types HFD-R and physical properties, chemical properties, oxidative stability,
HFD-U. Type HFD-R fluids are based on phosphate esters and corrosion, fire-resistance, biological and ecological compatibil-
Type HFD-U fluids are based on polyol esters. ity, other bench tests, and pump tests. A summary of important
5.4 Biodegradable Hydraulic Fluids: fluid properties and associated test procedures is provided in
5.4.1 Type HETG Hydraulic Fluids—Typically, biodegrad- Table 1.
able, water–insoluble hydraulic fluids derived from vegetable
oils. These fluids may be used at operating temperatures of -20 NOTE 1—Every test is not appropriate for every fluid class shown in
Table 1. The test procedures that are appropriate for a given fluid class are
to <80°C.
identified by an “X.”
5.4.2 Type HEES Hydraulic Fluids—Typically biodegrad-
NOTE 2—Every fluid test shown in the table need not be performed
able fluids derived from synthetic esters, such as polyol ester before for every pump test; however, it is recommended that after
and diesters, which may be used at operating temperatures of selecting those tests that are deemed most critical for the hydraulic fluid
−35 to <90°C. to be tested, that the test selection and properties of interest be reviewed
5.4.3 Type HEPG Hydraulic Fluids—Polyalkylene glycol with the component manufacturer to ensure that the fluid properties will
derived fluids that may be water-soluble or insoluble with meet the design and operational requirements for both the pump/motor/
varying degrees of biodegradability and fire resistance. These components and the application of interest before the hydraulic piston
pump test is conducted.
fluids are suitable for use at operating temperatures of -30 to
<90°C. 6.2 Typical Physical Properties:
5.4.4 Type HEPR Hydraulic Fluids—Biodegradable fluids 6.2.1 ISO Viscosity Grade (Classification D 2422)—The
whose basestocks are derived from polyalphaolefin and related International Standards Organization has established a viscos-
hydrocarbons. ity classification system for industrial fluid lubricants. Such
5.4.5 Other Biodegradable Fluids—Paragraphs 5.4.1-5.4.4 lubricants are classified by grades designated as ISO-VG based
describe HETG, HEES, HEPG, and HEPR fluids as biodegrad- on their viscosities in centistokes at 40°C. The choice of
able fluids. However, there are other types of biodegradable viscosity grade for use in a particular hydraulic system should
fluids not included in a listing. Fluid biodegradability is meet the manufacturer’s recommendations.
TABLE 1 Hydraulic Fluid Physical Property Characterization Tests
Hydraulic Fluid Classification

Characteristics Test According to:
HH HL HM HV HETG HEES HEPG HEPR HFA HFB HFD HFC
Kinematic viscosity at 40°C X X X X X X X X X X X X ASTM D 445

Low Temperature Viscosity X X X X X X X X X X X X ASTM D 2983, ASTM D 6080
ISO Viscosity Grade X X X X X X X X X X X X ASTM D 2422
Viscosity Index X X X X X X X X X X X X ASTM D 2270
Pour point X X X X X X X X X X X X ASTM D 97
Density at 15°C X X X X X X X X X X X X ASTM D 1298, ASTM D 4052
Air release at 50°C X X X X X X X X X X X X ASTM D 3427
Foam volumes (5 min. blowing, 10 min settling) X X X X X X X X X X X X ASTM D 892
Sequence I
Initial Volume
Final Volume, Time
Sequence II
Initial Volume
Final Volume, Time
Sequence III
Initial Volume
Final Volume, Time
Emulsion stability at 54°C X X X X X X X X X ASTM D 1401
Viscosity Stability (Ultrasonic Test) X X X X X X X X X X X X ASTM D 5621
Dielectric Breakdown Voltage (45-65 Hz) X X X X ASTM D 877
Electrical Conductivity at 20°C X X X X X X X X X X X X ASTM D 4308
6
D 6813 – 02
TABLE 1 Continued
Thermal conductivity X X X X X X X X X X X X ASTM D 2717

Specific heat capacity at 20°C X X X X X X X X X X X X ASTM D 2766
Vapor pressure X X X X X X X X X X X X ASTM D 2879
Bulk Modulus X X X X X X X X X X X X ISO 6073
Fluid Cleanliness
Instrumental Test Method X X X X X X X X X X X X ISO 11171
Microscopic Test Method X X X X X X X X X X X X ASTM F 312, ISO 4407
Cleanliness Code X X X X X X X X X X X X ISO 4406
In-Line Sampling Method X X X X X X X X X X X X ISO 4021
Drum Sampling X X X X X X X X X X X X ISO 5884
Sediment Content X X X X X X X X X X X X ASTM D 2273
Seal Compatibility X X X X X X X X X X X X ASTM D 6546
Hydraulic Fluid Chemical Property Characterization Tests (Including Seal Compatibility)
Ash (sulfated ash) proportion by mass X X X X X X X X X X X X ASTM D 874, ASTM D 482
Water content—Hydraulic Oils X X X X X X X X X X X X ASTM D 95, ASTM D 1533,
ASTM D 6304, ASTM E 203
pH value at 20°C X X X ASTM E 70
Neutralization number X X X X X X X X X X X X ASTM D 664, ASTM D 974
Alkaline Reserve to pH 5.5 (0.1N HCl) X X X ASTM D 1121
Hydrolytic Stability (mg KOH, mg Cu/cm2) X X X X X X X X X X X X ASTM D 2619
Aniline Point X X X X X X X X X X X X ASTM D 611
Hydraulic Fluid Thermal and Oxidative Stability, Corrosion and Bench Test Characterization Tests
Oxidation Stability—TOST X X X X X X X X X ASTM D 943
Oxidation Stability—Cincinnati Milacron X X X X X X X X X ASTM D 2070
Oxidation Stability—RBOT X X X X X X ASTM D 2272
Oxidation Stability—Baader Test X X X X X X X X X DIN 51554, Part 3
Oxidation Stability X X X X X X X X X X X X DIN 51373
Sludging Tendency X X X X X X X X X ASTM D 4310
Thermal Stability (Copper and Steel Rods, sludge) X X X X X X X X ASTM D 2070
Turbine Oil Rust Test X X X X X X X X X X X X ASTM D 665
Copper Corrosion X X X X X X X X X ASTM D 130
Galvanic Corrosion X X X X X X X X X X X X ASTM D 6547
Vapor Phase Corrosion X X X X X X X X X X X X ASTM D 5534
Corrosion X X X X X X X X X X X X LUX 5.9, ISO 4404
Aluminum
Brass
Cadmium
Copper
Magnesium
Steel
Zinc
Steel and Zinc
Copper and Zinc
Aluminum and Zinc
Steel and Aluminum
Four-Ball Anti-wear X X X X X X X X X X X X ASTM D 4172
Four-Ball Extreme Pressure X X X X X X X X X X X X ASTM D 2783
FZG-gear rig test method X X X X X X X X X X X X ASTM D 5182
Vane pump anti-wear test X X X X X X X X X X X X ASTM D 2882
AFNOR Filterability (dry) X X X X X X X X X AFNOR NF E48-690
AFNOR Filterability (wet) X X X X X X X X AFNOR NF E48-691
AFNOR Filterability (HDC and HFD) X X AFNOR NF E48-692
ISO Filterability (Dry) X X X X X X X X X ISO 13357-2
Hydraulic Fluid Fire-Resistance Characterization Tests
Fire Point X X X X X X X X X ASTM D 92
Flash Point (Open Cup) X X X X X X X X X ASTM D 92
Determination of auto ignition temperature X X X X X X X X X ASTM E 659
Factory Mutual Tests: X X X X Factory Mutual Standard 6930
Hot Channel Ignition Test
Spray Ignition Test
7
D 6813 – 02
Linear Flame Propagation Test X ASTM D 5306
Hot Manifold Test X X X X
Wick Flame Persistence X X X X ISO 14935
Spray Flame Test X X X X ISO 15029
Biodegradability X X X X X X X X X X X X ASTM D 6006
Classification for Environmental Impact X X X X X X X X X X X X ASTM D 6046
Biodegradability X X X X X X X X X X X X ASTM D 6006
Classification for Environmental Impact X X X X X X X X X X X X ASTM D 6046
6.2.2 Viscosity (Test Methods D 445 and D 2983, and Prac- signers and operators for calculating system weight, internal
tice D 6080)—Viscosity is the measurement of a fluid’s resis- pressure, wall thickness, and pump requirements. Density (or
tance to flow; it is considered to be the most important relative density) is measured at, or converted to, a standard
characteristic of a hydraulic fluid. The optimum value is reference temperature, normally either 15°C or 60°F, and these
always a compromise; it has to be high enough, at the working need to be quoted alongside the result. Test Method D 1298
temperature, to ensure that the fluid will not leak through the uses a hydrometer plus thermometer for measurement while
seals or junctions and to maintain proper lubrication. Also, the Test Method D 4052 uses a digital density meter.
viscosity has to be low enough to ensure fluid flow at start-up 6.2.5 Pour Point (Test Method D 97, Low Temperature
and to maintain system efficiency and lubrication and avoid Viscosity (Test Method D 2983)—The pour point is an indica-
cavitation. tion of the lowest temperature at which an oil will flow by
6.2.2.1 High VI hydraulic fluids often contain high molecu- gravity. The fluid viscosity must allow the system to start up
lar weight thickeners, called viscosity index (VI) improvers, and operate at low temperatures. As a practical rule, the fluid
which may impart non-Newtonian characteristics to the fluid. should have a pour point 10°C below the minimum expected
These polymers may shear degrade with use, and reduce the ambient temperature. Test Method D 2983 can be used to
in-service viscosity of the fluids. Practice D 6080 provides determine the temperature at which a fluid’s viscosity is less
uniform guidelines for characterizing oils in terms of both their than 750 cP, which is suggested as the highest viscosity which
high and low temperature viscosities before and after exposure the equipment can tolerate without risk of damage during
to high shear stress. Since the performance of fluids at operation.
temperatures higher than 40°C is determined in the worst case, 6.2.6 Shear Stability (Test Method D 5621)—Hydraulic flu-
that is, most severe situation, by the sheared oil viscosity, the ids may be subjected to shear rates $106 sec-1, which may lead
viscosity and viscosity index used to characterize fluids in this to a permanent viscosity loss due to polymer additive degra-
practice are those of the sheared fluid. dation. Test Method D 5621 covers the evaluation of the shear
6.2.2.2 Practice D 6080 classifies oils at low temperature by stability of a hydraulic fluid in terms of the final viscosity that
their new oil properties. Low temperature viscosities do not results from irradiating a sample of the hydraulic fluid in a
decrease greatly, if at all, with polymer shear degradation. sonic oscillator. Evidence has been presented that a good
Furthermore, this approach ensures that the fluid will be correlation exists between the shear degradation that results
properly classified under worst-case conditions, that is, when from sonic oscillation and that obtained in a vane pump test
the fluid is new. Practice D 6080 may be used with new or procedure.
used, Newtonian or non- Newtonian, hydraulic fluids. This 6.2.7 Foaming Characteristics (Test Method D 892)—In oil
practice is used for the determination of viscosities at low systems having high circulation rates, it is important that air
temperatures applicable to all hydraulic fluids based either on introduced through the seals or at the reservoir tank be readily
petroleum, synthetic, or naturally occurring base stocks. It is released from the body of the fluid and not collect as foam on
not intended for water-containing hydraulic fluids. the surface of the fluid, since this can produce cavitation or
6.2.3 Viscosity Index (VI) (Practice D 2270)—The VI num- impede proper circulation. Test Method D 892 measures the
ber signifies the decrease of a fluid’s viscosity as the tempera- tendency of the oil to form foam, and the stability of the foam.
ture increases. The greater the VI, the less viscosity changes There are three sequences: Sequence I at 24°C; Sequence II at
with temperature. In general, the VI is not very critical when 93.5°C; and Sequence III at 24°C, using the same sample
the system works at a stable operating temperature. When the tested in Sequence II.
variation of temperature among different points in the system is 6.2.8 Air Release (Test Method D 3427)—Agitation of lu-
high (over 30°C), or the operational temperatures vary consid- bricating oil with air in the equipment may produce a disper-
erably, then a high VI (over 90) is usually recommended. sion of finely divided air bubbles in the oil. If the residence
6.2.4 Density—Relative Density (Test Methods D 1298 and time in the reservoir is too short to allow air bubbles to rise to
D 4052)—This property is of value to hydraulic system de- the surface, a mixture of air and oil will circulate through the
8
D 6813 – 02
lubrication system. This may result in the inability to maintain 6.2.13.2 Procedure B is used to determine the breakdown
oil pressure, incomplete oil films in contact zones, and poor voltage of liquids in which any insoluble breakdown products
hydraulic system performance or failure. This test measures the do not completely settle from the space between the disks
time for the entrained air content to fall to the relatively low during the 1-min interval required in Procedure A (6.2.13.1).
value of 0.2 % volume under standardized test conditions, and Procedure B should also be applied for the determination of the
hence permits the comparison of the oils’ capacity to separate breakdown voltage of liquid samples containing insoluble
entrained air over a period of time. materials that settle from the specimen during testing. These
6.2.9 Water Separability (Demulsibility) Characteristics examples represent samples that may have large differences
(Test Method D 1401)—Water in large hydraulic systems may between replicate tests. The use of Procedure B will result in a
be removed from water insoluble fluids by mechanical proce- more accurate value of breakdown voltage when testing such
dures that take advantage of the demulsibility properties of the liquids. Use Procedure B to establish the breakdown voltage of
oil. A contaminant in the emulsion can affect the viscosity of an insulating liquid where an ASTM specification does not
the circulating fluid, creating lubrication problems and may exist or when developing a value for an ASTM guide or
lead to deposits. Test Method D 1401 determines the gross standard. Procedure A may be used once its single operator
water separation characteristics of oils. precision has been demonstrated.
6.2.14 Resistivity (Test Method D 1169)—Resistivity (r) is
NOTE 3—Many, if not most, used oils from Test Method D 1401
the property of a material which determines its resistance to
contain residual levels of water equal to or exceeding amounts sufficient
to shorten oil life. Therefore, rapid water separation in Test Method flow of an electric current, expressed by:
D 1401 does not imply that testing oils with low levels of water r 5 R · A/l (8)
contamination should not be done.
where:
6.2.10 Thermal Conductivity (Test Method D 2717) and R = resistance of the specimen, V,
Specific Heat (Test Method D 2766)—The thermal conductiv- A = cross-sectional area, cm2, and
ity and specific heats of hydraulic fluids are important fluid l = length of the specimen, cm.
design parameters. These properties may be determined from Resistivity is the inverse of conductivity. Resistivity is an
Test Methods D 2717 and D 2766 respectively. important parameter in determining the potential for electro-
6.2.11 Electrical Conductivity (Test Methods D 2624)—The chemical erosion (pitting corrosion) in a hydraulic system (1).
ability of a fluid to dissipate charge during pumping and High resistivity reflects low content of free ions and ion-
filtering operations is controlled by its electrical conductivity, forming particles, and normally indicates a low concentration
which depends on the content of ionic species. Electrical of conductive contaminants. Test Method D 1169 involves the
conductivity is an important parameter in determining the use of a dc galvanometer to measure electrical current flow in
potential for a hydraulic fluid to cause electrochemical erosion a test cell containing the hydraulic fluid.
(chemical pitting). Hydraulic fluid conductivity may be deter- 6.2.15 Vapor Pressure (Test Method D 2879)—One of the
mined by Test Methods D 2624. most critically important properties which must be accommo-
6.2.12 Dielectric Breakdown Voltage (Test Method dated in hydraulic system design is the vapor pressure of a
D 877)—Some users require that a minimum breakdown hydraulic fluid at its operating temperature. If the vapor
voltage be reported for applications like cherry pickers work- pressure is sufficiently high, the potential for cavitation may
ing near electric lines. This test method is used to judge if the increase dramatically. Vapor pressure may be measured using
disk electrode breakdown voltage requirements are met for an isoteniscope by Test Method D 2879. This test method
insulating liquids, as delivered from the manufacturer, that measures the vapor pressure of the fluid as received, including
have never been filtered or dried. (See Specification D 3487, most volatile components, but it excludes dissolved fixed gases
Specification D 4652, and Guide D 5222 for the minimum such as air.
specified electrical breakdown.) The breakdown test uses ac 6.2.16 Bulk Modulus (Test Method ISO 6073)—Bulk modu-
voltage in the power-frequency range from 45 to 65 Hz. The lus is a measure of the resistance to compressibility. The bulk
sensitivity of this test method to the general population of modulus of a hydraulic fluid is important because power is
contaminants present in a liquid sample decreases as applied transmitted and controlled under pressure in a hydraulic circuit.
test voltages used in this test method become greater than Test Method ISO 6073 (NFPA/T2.13.7R1-1996) provides a
approximately 25 kV rms. If the concentration of water in the procedure for predicting the bulk moduli of hydraulic fluids. In
sample at room temperature is less than 60 % of saturation, the this test method, it is assumed that there are no gas bubbles in
sensitivity of this test method to the presence of water is the fluid. The useful temperature range is from 0 to 270°C with
decreased. a pressure range from atmospheric to 700 000 kPa (7000 bar).
6.2.13 This test method describes two procedures, A and B, 6.2.17 Elastomer Compatibility (Test Methods D 6546)—
for determining the electrical breakdown voltage of insulating Test Methods D 6546 provide procedures for measuring physi-
liquid specimens. cal properties of elastomer seals in the form of O-rings after
6.2.13.1 Procedure A is used to determine the breakdown exposure to industrial hydraulic fluids and thermal aging. The
voltage of liquids in which any insoluble breakdown products measured properties are then compared to the physical prop-
easily settle during the interval between the required repeated erties of elastomer seals that have not been exposed to the
breakdown tests. These liquids include petroleum oils and industrial hydraulic fluids and thermal aging. The changes in
hydrocarbons. these properties form a basis for assessing compatibility when
9
D 6813 – 02
these changes are compared against the suggested limits. Fine, ISO Medium, and ISO Coarse.
6.2.17.1 These test methods provide procedures for expos- 6.2.19.3 The coding procedure for contaminant number and
ing O-ring test specimens to industrial hydraulic fluids under size distribution to be used in defining the quantity of solid
definite conditions of temperature and time. The resulting particles in the fluid in a given hydraulic system is described in
deterioration of the O-ring material is determined by compar- ISO 4406. This test method provides a three-part code for
ing the changes in work function, hardness, physical proper- contamination levels measured with automatic particle
ties, compression set, and seal volume after immersion in the counters calibrated in accordance with ISO 11171. The re-
test fluid to the pre-immersion values. ported particle sizes are 4 µm, $6 µm, and $14 µm. It also
6.2.18 Sediment Content (Test Method D 2273)—This test introduces equivalent particle sizes for such counters, based on
method covers the determination of trace amounts (less than calibration with NIST reference material SRM 2806.
0.05 volume %) of sediment in lubricating oils. Since oil- 6.3 Typical Chemical Properties:
soluble material precipitated by the specified solvent is not 6.3.1 Neutralization Number (Test Methods D 664 and
intended as part of the measured sediment, this test method is D 974)—Oxidation of hydraulic fluids may be monitored by
not applicable in cases where precipitated oil-soluble compo- tracking increases in the acid number. Because the fresh fluid
nents will appreciably contribute to the sediment readings. may be either alkaline or acidic, depending on the additives
6.2.19 Fluid Cleanliness (Test Method ISO 4406, 4021, and present, the value of the acid number of the fresh fluid is not
11171)—Fluid cleanliness is an important parameter since dirt indicative of quality. However, increasing acid numbers gen-
contaminants and wear debris may lead to erosive or abrasive erally indicate increasing amounts of oxidation.
wear in the system and interfere with the operation of various
NOTE 5—With ester-based fluids, the acid number of the fresh fluid is
components such as servovalves. Therefore, reliable system indicative of quality, since esters hydrolyze quicker in the presence of
performance requires contamination monitoring and control acid.
procedures.
6.2.19.1 Qualitative and quantitative determination of the 6.3.1.1 The acid number is determined by titrating a sample
particulate contaminants in a hydraulic fluid requires precision of known size with a known amount of standard base (Test
in obtaining the sample and determination of the nature and Methods D 664 or D 974). The test is performed by dissolving
extent of the contaminant in addition to particle size and the oil in a mixture of toluene and isopropanol, to which has
concentration. Hydraulic fluid samples must be representative been added a small amount of water, then titrating it with a
of the particle contaminant in the fluid flowing at the point of standard solution of potassium hydroxide (KOH). The end-
sampling. The most representative sample is obtained from the point may be determined potentiometrically or colorimetrically
system while the fluid is flowing in a turbulent manner. Line with a pH-sensitive indicator. The acid number (AN) is
sampling procedures that provide the necessary representative reported in units of milligrams of KOH per gram of sample
system cleanliness results are described in detail in ISO 4021. (mg KOH/g). It should be noted that the acid number obtained
A fluid samples taken in this manner is designated as a dynamic by Test Method D 974 may or may not be numerically the same
sample. There are several procedures and devises for sampling as those obtained by Test Method D 664, but it is generally of
drums, barrels, etc. such as ISO 5884. Liquid automatic the same order of magnitude.
particle counters are an accepted means of determining the 6.3.2 Hydrolytic Stability (Test Method D 2619)—The resis-
concentration and size distribution of the contaminant par- tance of hydraulic fluids to hydrolysis is important. Reaction of
ticles. Individual instrument accuracy is established through a finished product with water can lead to the formation of
calibration. ISO 11171 provides procedures for: corrosive substances, acids, insoluble by-products, and stable
(1) Primary particle-sizing, sensor resolution, and counting emulsions which can, in turn, cause corrosion, sticky valves,
performance; plugged filters, and change in oil viscosity. However, some
(2) Secondary particle-sizing calibration using suspensions hydraulic fluids are not hydrolytically stable (see Specification
prepared with NIST reference materials; D 4293). Hydrolytic stability may be evaluated by the Bever-
(3) Establishing acceptable operation and performance age Bottle Test (Test Method D 2619) where the hydraulic fluid
limits; and water are heated at 200°F for 48 h in the presence of a
(4) Verifying particle sensor performance using a truncated copper test specimen. Changes in viscosity and acid number of
test dust procedure; and the fluid and acid number of the aqueous layer are determined
(5) Determining coincidence and flow rate limits in the after the test. Copper weight change and appearance are also
particle counter. measured.
6.3.3 Water Content (Test Methods D 1123, D 1533,
NOTE 4—ISO 11171 replaces the ISO 4402 method of calibrating D 6304, D 95, and E 203)—The presence of water in a
automatic particle counters which is now obsolete.
hydraulic oil, which may be present due to condensation or a
6.2.19.2 Quantitative counting of particles may also be leaking heat exchanger, presents a potentially serious problem.
performed by microscopic counting. The microscopic tech- Test Methods D 1123, D 1533, and D 6304 are quantitative
nique is described in Test Methods F 312 and ISO 4407. Thus tests for water content which uses the reaction of water with
far, there is no standard procedure that has been reported for Karl Fisher chemical reagent as its basis, and a coulometric end
the use of automatic particle counters, although there are point as the measurement. Test Method D 1533 is used for
calibration procedures using a synthetic test dust (see ISO water contents <200 ppm and Test Method D 6304 is used
11171). The test dusts are designated as are ISO Ultrafine, ISO when the water content is in the range from 10 to 25 000
10
D 6813 – 02
mg/kg (0.1 mass %). The components of some fluids may react the data should be interpreted with caution.
with the reagent to give misleading results. NOTE 10—There is evidence that samples containing molybdenum or
6.3.3.1 Test Method E 203 is intended as a general guide for boron can give low results because compounds of these metals are not
fully recovered at the temperature of ashing.
the application of the volumetric Karl Fischer (KF) titration for
determining free water and water of hydration in most solid or 6.3.6 pH Determination (Test Method E 70)—Test Method
liquid organic and inorganic compounds. This test method is E 70 specifies the apparatus and procedures for the electromet-
designed for use with automatic titration systems capable of ric measurement of pH values of aqueous solutions with the
determining the KF titration end point amperometrically; glass electrode. It does not deal with the manner in which the
however, a manual titration method for determining the end solutions are prepared. The pH measurements of good preci-
point visually is included. This test method covers the use of sion can be made in aqueous solutions containing high con-
both pyridine-containing and pyridine-free KF reagents for centrations of electrolytes or water-soluble organic com-
determining water by volumetric titration. Determination of pounds, or both. It should be understood, however, that pH
water using KF coulometric titration is not discussed. By measurements in such solutions are only a semiquantitative
proper choice of the sample size, KF reagent concentration, indication of hydrogen ion concentration or activity. The
and apparatus, this test method is suitable for measurement of measured pH will yield an accurate result for these quantities
water over a wide concentration range, that is, from parts per only when the composition of the medium matches approxi-
million to pure water. mately that of the standard reference solutions. In general, this
6.3.3.2 For relatively high concentrations of water, Test test method will not give an accurate measure of hydrogen ion
Method D 95, using distillation, may be used. Test Method activity unless the pH lies between 2 and 12 and the concen-
E 203 is useful for water contents varying from the parts per tration of neither electrolytes nor nonelectrolytes exceeds 0.1
million (ppm) range to pure water. M.
6.3.3.3 Fire-resistant hydraulic fluids, including HFA, HFB, 6.3.7 Alkaline Reserve to pH 5.5 (Test Method D 1121)—
and HFC fluids, have water contents of $35 %. In these fluids, Many water-containing hydraulic fluids, such as HFC fluids,
water is not a contaminant but a necessary component and the contain amines or basic salts as corrosion inhibitors. The total
water concentration must be determined and maintained to inhibitor content may be quantitatively determined using a
ensure adequate fire resistance and hydraulic system perfor- titrimetric procedure by titrating to a pH of 5.5 using 0.1 N HCl
mance. Water content may be determined by azeotropic distil- and a glass electrode. This procedure is described in Test
lation according to Test Method D 95 or by Karl Fischer Method D 1121.
Analysis according to Test Method E 203. 6.3.8 Aniline Point (Test Method D 611)—Elastomer com-
6.3.4 Ash Content (Test Method D 482)—Test Method patibility is affected by the composition of the mineral oil. The
D 482 covers the determination of ash in the range from 0.001 potential for a mineral oil to cause swelling or shrinkage of a
to 0.180 mass %, from distillate and residual fuels, gas turbine seal is important if optimal seal strength is to be maintained
fuels, crude oils, lubricating oils, waxes, and other petroleum and leakage is to be minimized. One of the oldest methods of
products, in which any ash-forming materials present are estimating hydraulic seal compatibility with a mineral oil is the
normally considered to be undesirable impurities or contami- aniline point of the fluid. Generally, fluids with low aniline
nants (see Note 6). This test method is limited to petroleum points cause the highest swelling with neoprene and BUNA-N
products which are free from added ash-forming additives, nitrile rubber (see Note 11) and fluids with high aniline points
including certain phosphorus compounds (see Note 7). may cause seal shrinkage.
6.3.8.1 The aniline point (or mixed aniline point) described
NOTE 6—In certain types of samples, all of the ash-forming metals are
by Test Method D 611 is useful as an aid in the characterization
not retained quantitatively in the ash. This is particularly true of distillate
oils, which require a special ash procedure in order to retain metals of pure hydrocarbons and in the analysis of hydrocarbon
quantitatively. mixtures. The test is conducted with specified volumes of
NOTE 7—This test method is not intended for the analysis of unused aniline and sample, or aniline and sample plus n-heptane,
lubricating oils containing additives; for such samples, use Test Method which are placed in a tube and mixed mechanically. The
D 874 (see 6.3.5). Neither is it intended for the analysis of lubricating oils mixture is heated at a controlled rate until the two phases
containing lead nor for used engine crankcase oils. become miscible. The mixture is then cooled at a controlled
6.3.5 Sulfated Ash Content (Test Method D 874)—Test rate and the temperature at which two phases separate is
Method D 874 covers the determination of the sulfated ash recorded as the aniline point or mixed aniline point. Aromatic
from unused lubricating oils, such as hydraulic fluids, contain- hydrocarbons exhibit the lowest, and paraffins the highest
ing additives and from additive concentrates used in com- values. Cycloparaffins and olefins exhibit values that lie
pounding. These additives usually contain one or more of the between those for paraffins and aromatics.
following metals: barium, calcium, magnesium, zinc, potas- NOTE 11—Although generally true, it has not been possible to calibrate
sium, sodium, and tin. the aniline point of an oil to predict the swelling of various elastomeric
seal compositions with respect to different base oils and additive combi-
NOTE 8—This test method is not intended for the analysis of used
nations. For example, ester-based hydraulic fluids often aid seal swell
engine oils or oils containing lead. Neither is it recommended for the
problems and they may be used to counteract the tendency of
analysis of nonadditive lubricating oils, for which Test Method D 482 can
hydrocarbon-based fluids to shrink seals. Also, some fluids contain seal
be used.
swell additives.
NOTE 9—There is evidence that magnesium does not react the same as
other alkali metals in this test method. If magnesium additives are present, 6.4 Tests for Thermal and Oxidation Stability:
11
D 6813 – 02
6.4.1 Thermal Stability—Cincinnati Milacron Test (Test test solution while maintaining the temperature at 120°C.
Method D 2070)—The thermal degradation of a lubricant can Volatile acidic by-products are collected in water contained in
yield by-products which corrode metals, as well as insoluble a downstream absorption tube. At the conclusion of the test, the
materials which plug filters and block narrow clearances. This acid number is determined in the test fluid and the acids
test method is designed primarily to evaluate the thermal collected in the absorption tube are titrated with base and
stability of hydrocarbon-based hydraulic oils in the presence of reported as mg KOH/g of the test fluid. The change in mass of
copper and steel at 135°C although oxidation may occur during the copper and iron specimens is determined.
the test. The colors of the test rods are the evaluation criteria. 6.4.6 Sludging Tendency (Test Method D 4310)—As stated
The tendency of oils to form sludge at high temperatures in the in Oxidation Stability (Test Method D 943), insoluble or
absence of water and in the presence of iron and copper is also corrosive materials may form in oils when they are subjected to
reported. oxidation conditions. This 1000-h test determines the tendency
6.4.2 Oxidation Stability—Turbine Oil Stability Test (Test of oil to form sludge in the presence of oxygen, water, and
Method D 943)—Oxidation of the oil may increase oil viscos- metal catalysts. Test Method D 4310 also measures the total
ity, produce sludge that can make valves stick and plug filters, copper present in the oil, water, and sludge phases. It is a
and generate materials which are corrosive to metals. Test complement to Test Method D 943.
Method D 943, also known as Turbine Oil Stability Test 6.5 Typical Corrosion Properties:
(TOST), measures the time that the oil resists oxidation in the 6.5.1 Rust Preventing Characteristics (Test Method
presence of oxygen, water, and metal catalysts. It should be D 665)—This test method measures the ability of the oil to
recognized, however, that correlation between results of this prevent rusting of steel surfaces when water is present.
test method and the oxidation stability of a lubricant in field Procedure A uses distilled water, and Procedure B uses
service can vary markedly with field service conditions. This synthetic sea water. The procedure also provides for testing
test method does not measure sludge formation or catalyst coil heavier-than-water fluids.
corrosion (see Test Method D 4310). 6.5.2 Copper Corrosion Characteristics (Test Method
6.4.3 Oxidation Stability (Test Method D 2272)—This test, D 130)—Some components of hydraulic systems contain cop-
familiarly known as the Rotating Bomb Oxidation Test per alloys (for example, vane pump bushings and piston pump
(RBOT), utilizes an oxygen-pressured vessel to evaluate the shoes). This test method covers the detection of the corrosive-
oxidation stability of new and in-service turbine oils having the ness to copper of hydraulic oils and other hydrocarbons having
same composition (base stock and additives) in the presence of a Reid vapor pressure no greater than 18 psi (124 kPa).
water and a copper catalyst coil at 150°C. The estimate of 6.5.3 Vapor Phase Corrosion Characteristics (Test Method
oxidation stability is useful in controlling the continuity of this D 5534)—Test Method D 5534 evaluates the ability of a
property for batch acceptance of production lots having the water-containing hydraulic fluid to prevent rusting of steel in
same operation. This test method is also used to assess the the vapor phase over the hydraulic fluid and water.
remaining oxidation life of in-service oils. Although it was 6.5.4 Determination of the Corrosion-Inhibiting Properties
developed for turbine oils, it is routinely used for other of Fluids (Test Method LUX 5.9)—It is important that fire-
industrial lubricants, including hydraulic oils. resistant hydraulic fluids do not cause corrosion of the equip-
6.4.4 Oxidation Stability—Baader Test (DIN 51554-3)— ment in which they are used. The tests described in Section 5.9
Neither Test Method D 943 (TOST) nor Test Method D 2272 of the Seventh Luxembourg Report (also see ISO 4404) are
(RBOT) discussed in 6.4.2 and 6.4.3 is suitable for use with designed to determine corrosion-inhibiting properties of the
hydrolytically unstable hydraulic fluids such as vegetable fluids in contact with selected metals or metal pairs.
oil-based fluids, synthetic esters, or polyol esters, since water is 6.5.4.1 One of the testing methods described is character-
used as a component of the test procedure (see Note 12). One ized by a low test temperature (35°) and a long duration of 28
test that has been used to determine the oxidative stability of days. The second testing method is similar except a higher
hydrolytically sensitive fluids is DIN 51554-3, also known as testing temperature (60°C) and a shorter testing time of 14 days
the Baader test. It is conducted at 95°C for three days in the is used.
presence of air and a copper wire catalyst. At that point, the
6.5.5 Galvanic Corrosion (Test Method D 6547)—Galvanic
fluid is visually examined and then the saponification number
corrosion is recognizable by the appearance of increased
is determined.
corrosion near the junction of dissimilar metals. This is caused
NOTE 12—Recent work in ASTM D02.N0.03 has shown that if Test by an electrochemical reaction between metals. The propensity
Method D 943 is conducted without the addition of water (dry), this for galvanic corrosion is dependent on the position of the two
modified test provides a suitable assessment of the oxidative stability of metals in the galvanic series. Any metal will have a greater
vegetable oils. tendency to corrode when it is in contact with another metal in
6.4.5 Oxidation Stability of Phosphate Ester Fluids (DIN a lower position in the series in the presence of an electrolyte.
51373)—Another test that is reported in ISO 12922 for The farther apart the two metals in the series, the greater the
determination of the oxidative stability of fire-resistant phos- potential for galvanic attack.
phate ester-based hydraulic fluids is DIN 51373. This test 6.5.5.1 Test Method D 6547 provides a test method for
method characterizes resistance to oxidation and provides a determination of the corrosiveness of hydraulic and lubricating
measure of resistance to corrosion of copper and steel. This test fluids to a brass on steel galvanic couple at ambient tempera-
is performed by passing oxygen at 1 L/h for 164 h through the ture and 50 % relative humidity. This test method consists of
12
D 6813 – 02
fitting a brass clip to the fluid-coated surface of a steel disk, metal surface for 60 s, after it is preheated to 1300°F (704°C)
storing the assembly at approximately 50 % relative humidity and the burners are turned off. In order to be considered a
for ten days, and visually inspecting the assembly for evidence “pass” in this test, the fluid must not propagate and must not
of galvanic corrosion. follow the spray source. The second part is a spray ignition
6.6 Selected Tests for Fire Resistance—Fire resistance tests flammability test where a propane torch flame is rotated
are established by various authorities, depending on the indus- through a spray of the hydraulic fluid. The fluid spray flame, if
try and country where the hydraulic fluid will be used. An established, must be self-extinguishing within 5 s after removal
exhaustive global listing of these tests is beyond the scope of of the ignition source in order to be considered a “pass.”
this guide. Ref (2) provides a more comprehensive overview of 6.6.4.2 Mine Safety and Health Administration (MSHA)
fire-resistance testing than is possible here (2). However, CFR Part 35 Test Method (3)—The CFR Part 35 Test Method
assessment of fire resistance is often a criterion of fluid contains three parts and a hydraulic fluid must pass all three
selection. Therefore, some of the more common tests used in parts. The first part is an autoignition temperature (AIT) test
Europe and the United States are provided for reference in which is conducted according to Test Method E 659. If the AIT
Table 1. is >600°F, the fluid is considered a “pass.” The second part is
6.6.1 Flash Point and Fire Point (Test Methods D 92 and a temperature-pressure spray ignition test. If the fluid flame, if
D 93)—Flash point is defined as the lowest temperature formed, self-extinguishes in <1 min, it is considered a “pass.”
corrected to barometric pressure of 101.3 kPa (760 mm Hg) at The third part of this test evaluates the effect of evaporation on
which the application of an ignition source causes the vapors of flammability. It is also commonly called the “pipe cleaner” test.
a test specimen of the sample to ignite under specified In this test, a pipe cleaner saturated with the hydraulic fluid
conditions of the test. Experimentally, the flash point is being tested is cycled through a Bunsen burner flame at 25 6
determined by passing a flame over a test specimen contained 2 cycles/min. To be considered a “pass,” the average number of
in a test cup and heated at a constant rate. The flash point is cycles through the flame before ignition shall be at least 24.
determined to be that temperature where the fluid will flash but 6.7 Biodegradability and Aqueous Toxicity—Although the
not continue to burn when a flame is passed over the cup. It is biodegradability and ecotoxicity properties of a hydraulic fluid
indirectly a measure of both the volatility of the oil and do not dictate their performance in a hydraulic pump, they are
flammability of the volatiles contained therein. The fire point often important screening properties. In many cases, if a
of a fluid is defined as the lowest temperature corrected to hydraulic fluid does not exhibit acceptable biodegradability
barometric pressure of 101.3 kPa (760 mm Hg) at which the and ecotoxicity, it will be rejected and not be evaluated in
application of an ignition source causes the vapors of a test expensive and time-consuming pump tests.
specimen of the sample to ignite and sustain burning for a 6.7.1 Biodegradability (Guide D 6006)—Guide D 6006
minimum of 5 s under specified conditions of the test. provides information to assist in judging the biodegradability
6.6.1.1 Test Method D 92 describes the determination of of an unused fully formulated hydraulic fluid in its original
flash and fire points of a fluid using the Cleveland Open Cup form. Biodegradability is one of three characteristics which are
(COC) test procedure. Test Methods D 93 describes the deter- assessed when judging the environmental impact of a hydraulic
mination of flash point under closed cup conditions using the fluid. The other two characteristics are ecotoxicity and bioac-
Pensky-Martens Closed Cup Tester. cumulation. Biodegradability may be considered by type of
6.6.2 Autoignition Temperature (Test Method E 659)— environmental compartment: aerobic fresh water, aerobic ma-
Autoignition is the temperature at which the fluid will ignite rine, aerobic soil, and anaerobic media. Test methods for
spontaneously in contact with air. This test method covers the aerobic fresh water- , aerobic soil and anaerobic media have
determination of hot- and cool-flame autoignition temperatures been developed that are appropriate for the concerns and needs
of a liquid chemical in air at atmospheric pressure in a of testing in these compartments.
uniformly heated vessel. 6.7.1.1 Guide D 6006 addresses releases to the environment
6.6.3 Linear Flame Propagation Test (Test Method that are incidental to the use of a hydraulic fluid but is not
D 5306)—Test Method D 5306 covers the determination of intended to cover situations of major, accidental release.
linear flame propagation rates of hydraulic fluids supported on Nothing in this guide should be taken to relieve the user of the
the surfaces of, and when impregnated into, ceramic fiber responsibility to properly use and dispose of hydraulic fluids.
media. The linear flame propagation rate is a property that is 6.7.2 Classification of Fluids for Environmental Impact
relevant to the overall assessment of the flammability or (Classification D 6046)—This classification establishes a
relative ignitability of fire-resistant hydraulic fluids. framework to categorize the biodegradability, toxicity, and
6.6.4 Other Fire Resistance Testing Methods—Various fire bioaccumulation impact of hydraulic fluids on different envi-
resistance tests are summarized in Table 1. However, two of the ronmental compartments. Fluids are assigned designations
most common testing procedures encountered in the United within these categories; for example Pw1, Tw2, and so forth,
States are the Factory Mutual Test 6930 and the Mine Safety based on performance in specified tests.
and Health Administration (MSHA) tests cited in CFR Part 6.7.3 In the current version of this classification, the aspects
35(3). of environmental impact included are environmental persis-
6.6.4.1 Factory Mutual Test Method D 6930 (4)—This is a tence (biodegradability) and acute ecotoxicity. Although envi-
two part test procedure. The first part is a hot channel spray ronmental persistence is discussed first, this classification does
flammability test where the hydraulic fluid is sprayed onto a not imply that considerations of environmental persistence
13
D 6813 – 02
should take precedence over concerns for ecotoxicity. Another specific properties have been conferred by the use of insoluble/partially
important aspect of environmental impact is bioaccumulation. soluble additives, or by particularly large molecular species.
This aspect is not addressed in the present classification 6.8.1.3 For fire-resistant fluids, HFC and HFD, a filter
because adequate test methods do not yet exist to measure membrane made of polytetrafluoroethylene (Millipore Fluo-
bioaccumulation of hydraulic fluids. The present classification ropore FALP 047 IF) is used for AFNOR NF E48-692. Both
addresses the fresh water and soil environmental compart- the membrane area (47 mm diameter) and pore size (1 µm) are
ments. At this time marine and anaerobic environmental defined.
compartments are not included, although they are pertinent for 6.9 Anti-wear Performance—Preliminary assessment of the
many uses of hydraulic fluids. Hydraulic fluids are expected to lubricating performance of a hydraulic fluid is typically per-
have no significant impact on the atmosphere; therefore, that formed prior to conducting relatively expensive and time-
compartment is not addressed. consuming piston pump tests. These preliminary tests can be
NOTE 13—This classification addresses the potential impact of releases classified as “bench” tests and “pump” tests. The bench tests
to the environment which are incidental to the use of a hydraulic fluid. The are standardized lubrication tests and the most commonly
classification is not intended to address environmental impact in situations encountered are described in 6.9.1. The most common pump
of major, accidental release. tests used for hydraulic fluid lubrication testing are either the
6.8 Filterability—Petroleum oil may be difficult to filter in Test Method D 2882 vane pump test or the Eaton 35VQ25
the presence of small amounts (<2 %) of water. In some cases, vane pump test (5).
this may result in plugging of system filters which may result NOTE 16—The vane pump tests described in 6.9 for assessing hydraulic
in increased abrasive wear of the hydraulic system compo- fluid lubrication provide an excellent indication of anti-wear performance
nents. It should be noted that filterability is not a physical under pure sliding conditions. Such information is a useful indicator for
characteristic of the oil but represents an estimation of its lubrication wear at sliding contacts in a piston pump which include: the
behavior in service. Therefore, an assessment of the filterability interface between the piston and the cylinder block, the interface between
of hydraulic oils is very important. the piston and the swash plate for some axial piston pumps, the interface
between the rotary valve plate and pump housing, and other wear surfaces.
6.8.1 Filterability (AFNOR Test Methods NF E48-690, NF However, correlation must be established by either experiment or expe-
E48-691, NF E48-692, ISO 13357-2—Fluid filterability for rience.
petroleum oil-derived fluids is measured using a filtration
membrane made of mixed cellulose esters for AFNOR NF 6.9.1 Assessment of Anti-wear and EP Performance—Bench
E48-690 and AFNOR NF E48-691. The membrane area (47 Tests:
mm diameter) and pore size (0.8 µm) are defined (Millipore 6.9.1.1 Shell Four-Ball Tests (Test Methods D 2783 and
AA WP 047 IF). The AFNOR NF E48-690 test method is used D 4172)—Although of limited value for water-containing flu-
to assess the filterability of an oil which will be used in ids due to lack of fluid temperature control, four-ball tests may
applications where the presence of water in the oil is unlikely. provide a useful preliminary evaluation of the lubricating
The AFNOR NF E48-691 test method is used for assessing the properties of a hydraulic fluid.
filterability of oils that have been heat-soaked in the presence (1) Evaluation of Extreme Pressure (Load Carrying) Prop-
of water contamination. erties by the Four Ball Method (Test Method D 2783)—This
test method covers the determination of the load-carrying
NOTE 14—It is not impossible for an oil to have poor filterability when properties of lubricating fluids including hydraulic fluids. Two
dry, but good filterability when wet although it is unlikely that such an oil determinations are made: load-wear index (formerly Mean-
would be generally acceptable.
Hertz load) and the weld point by means of the four-ball
6.8.1.1 The “wet” oil samples are prepared by mixing 330 extreme-pressure (EP) tester.
mL of oil with 66 mL of water and then heat the mixed sample (2) Evaluation of Anti-wear Properties by the Four-Ball
in an oven at 70°C for 2 h. The sample is removed from the Method—(Test Method D 4172)—This test method covers a
oven, stirred again and then returned to the oven for 70 h at procedure for making a preliminary evaluation of the anti-wear
which time the sample is removed from the oven and stored at properties of fluid lubricants in sliding contact by means of the
ambient temperature in the dark for 24 h at which time it is Four-Ball Wear Test Machine.
ready for filterability testing. In the AFNOR test methods, the 6.9.1.2 FZG Test (Test Method D 5182)—This test method,
rate of filtration near the beginning of the test is measured, and the Forschungstelle fur Zahnrader und Getriebebau (Research
compared with the mean filtration rate throughout the test, or Site for Gears and Transmissions) Visual Method, commonly
with the rate at the end of the test. The filterability calculation referred to as the FZG Visual Method, is intended to measure
procedure affords a value that is independent of fluid viscosity, the scuffing load capacity of oils used to lubricate hardened
however, a constant fluid temperature must be maintained steel gears. It is primarily used to assess the resistance to
throughout the test. scuffing of mild additive treated oils such as industrial gear oils
6.8.1.2 Alternatively, filterability of petroleum oil hydraulic and transmission fluids. This test is widely used to predict
fluids may be assessed using ISO 13357-2. As with the anti-wear performance of hydraulic oils in vane pumps.
AFNOR procedures above, these test methods are not suitable 6.10 Assessment of Anti-wear Performance—Vane Pump
for use with HFC and HFD fire-resistant fluids due to their Tests:
incompatibility with the filter material. 6.10.1 Anti-wear Performance (Test Method D 2882)—
NOTE 15—The AFNOR NF E48-69 (ISO 13357-2) and AFNOR NF Hydraulic systems running at high pressures, designed with
E48-691 test procedures are not suitable for some hydraulic oils on which small clearances and subject to metal-to-metal contact (for
14
D 6813 – 02
example, vane, gear, and piston pumps) should use fluids that TABLE 3 Steady-State Operating Conditions for the Eaton
have anti-wear properties. Test Method D 2882 is a constant- 35VQ35 Vane Pump Test
volume vane pump test based on the Eaton V104C vane pump Speed 2400 rpm
Outlet Pressure 207 bar gage
(see Note 17). The evaluation parameter is the total weight loss Inlet Pressure 0 to 0.15 bar gage with flooded unit
of the ring and vanes. The test rig simulates anti-wear Inlet Temperature 93°C
performance provided by a hydraulic fluid at a sliding wear
contact in small hydraulic systems.
provides case pressure spikes, and it is representative of the
NOTE 17—Various national test methods have been issued based on the
Eaton V-104C pump but with slightly varying test conditions. A summary
“real world.” Deficiencies of cycled pressure tests are that this
of various test methods and testing conditions is provided in Table 2. procedure stresses the bearing and yoke assembly more than
NOTE 18—Test Method D 2882 is based on the use of the Eaton V104C the fluid life; cost for a robust stand; and less time at maximum
vane pump. However, the V104 pump and components are no longer and minimum shear and stress.
available from Eaton. Therefore, this test is currently being performed 7.1.2 Cycled Volume—A cycled volume test is conducted by
with replacement parts which are similar but not identical to certified alternating between a minimum and maximum volume per
Eaton replacement parts.
stroke and is conducted at a constant pressure. This type of test
6.10.2 Eaton 35VQ25 Vane Pump Test—For many higher influences component life more than providing maximum
pressure and higher speed operating conditions, a more rigor- stress on the fluid to evaluate fluid life properties. The
ous assessment of hydraulic fluid anti-wear properties is advantages and disadvantages are essentially analogous to
necessary. Therefore, Vickers Inc. developed the 35VQ25 vane those described in 7.1.1.
pump test (now designated as the Eaton 35VQ35 vane pump 7.1.3 Constant Pressure and Constant Volume—For the
test, to provide the most severe evaluation of hydraulic fluid greatest stress on the hydraulic fluid, it is recommended that
anti-wear performance in a Vickers intravane pump (5). The the pump be run at a constant pressure and volume at a
procedure for this test is outlined in Vickers Form No. maximum temperature. If low-temperature wear is a concern,
M-2952-S, now published by Eaton Corporation (6). The test then a low fluid temperature cycle may need to be included,
procedure involves the use of an Eaton 35VQ35 fixed displace- probably at the beginning of the test. Experience has shown
ment (81 cm3/rev) vane pump as the test pump. This pump that most wear occurs at the beginning of the test during “break
utilizes an intravane design replaceable cartridge which is rated in,” unless the fluid is deficient at the selected operating
at 2500 rpm and 207 bar (3000 psi). The test procedure utilizes conditions or reaches the end of its useful life during the test.
a minimum of three vane pump cartridges which are tested at 7.1.3.1 Advantages of the constant pressure test include:
50 h each. The 50 h test duration includes a one hour plus lower cost, simpler test stand; more durable test stand and
break-in period to allow the inlet fluid temperature and outlet higher stress on the hydraulic oil (maximum shearing and
pressure to be increased to the final test conditions shown in temperature rise). Variation in the system pressure load will not
Table 3. The remainder of the test is conducted in the provide any additional information about the fluid properties.
steady-state mode. Many people believe that since the pressure inside of the
cylinders is fluctuating, there is no need to further complicate
7. Pump Testing Procedures the system with additional pressure changes. The primary
7.1 Although numerous pump tests may be devised, most disadvantage of the constant pressure test is that this testing
are based on one, or combinations of two or more, of three procedure is not representative of common “real world”
testing strategies. These include: applications.
7.1.1 Cycled Load (Pressure)—A pump test may be run by
cycling between a higher and a lower pressure at a constant 8. Pump Stand Design
volume. This type of test procedure is beneficial because 8.1 Various pump testing procedures have been reported for
cycling the pressure affects the control system, slipper contact use in evaluating components under different operating condi-
varies, fluids change characteristics under pressure (for ex- tions. Three standards that describe different testing procedures
ample, cavitation, aeration), it evaluates cradle bearing scuff- but which are useful references in test design development are:
ing, it provides acceleration and deceleration of the fluid, it SAE J745, ANSI/(NFPA)T3.9.20 and ANSI/(NFPA)T3.9.33.
TABLE 2 Current Pump Testing Procedures Based on the Eaton V-104 Vane Pump
Inlet Temperature
Fluid Volume, Time, Pump Speed, Outlet Pressure, Power Requirement,
Procedure or Viscosity,A
L h rpm bar kW
C/cSt
B
ASTM D 2882 57 100 1200 140 7
DIN 51389/2C 70 250 1500 140 13 cSt 7
DIN 51389/3C 70 250 1500 105 13 cSt 7
IP 281 70 250 1500 102 13 cSt 7
CETOP RP 67 70 250 1500 102 13 cSt 7
A
Test Method D 2882 specifies the operating conditions by fluid temperature where the DIN 51389, IP 281, and CETOP methods specify that the running temperature
will be selected to provide a fluid viscosity of 13 cSt.
B
Fluid temperature at the pump inlet is 66 6 3°C (150 6 5°F) for all water glycols, emulsions, and other water-containing fluids and for petroleum and synthetic fluids
with 66 6 3°C (150 6 5°F) viscosities of 46 cSt (213 SUS) or less. A temperature of 80 6 3°C (175 6 5°F) is used for all other synthetic and petroleum fluids.
C
This is the test method for mineral oil hydraulic fluids. DIN 51389/3 is the method for fire-resistant fluids.
15
D 6813 – 02
As indicated in Section 7, there are numerous testing variations located such that adequate fluid supply to the operating circuit
that may be selected depending on the objective of the piston is maintained at the minimum operating fluid level and that air
pump test being performed. ANSI/JIC T2.24.1 provides basic ingression and the formation of vortices in the fluid are
guidance in the preparation of detailed equipment specifica- eliminated.
tions, and promotes personnel safety, and proper use of 8.2.1.2 Return feeds to the reservoir shall be discharged
hydraulic equipment. The most critical parameters that must be below the operating fluid level.
monitored for any test are discussed throughout Section 8. 8.2.1.3 Return feeds to the reservoir shall discharge at the
8.2 Fluid Residence Time (Reservoir Size)—The reservoir lowest practical velocity and shall promote the desired circu-
for the test stand should be of sufficient size to accommodate lation pattern within the reservoir and shall not promote air
fluid cooling and air release (7). However, the reservoir should entrainment.
also be sufficiently small to simulate the reservoir of an actual 8.2.1.4 The reservoir configuration shall be such that con-
system that would provide a fluid turnover time of 20 s or three taminants cannot be resuspended in the system fluid.
times per minute. 8.2.2 To facilitate air release of the hydraulic fluid returning
NOTE 19—The desired reservoir volume (VR) can be calculated from to the reservoir before it re-enters the inlet, it is recommended
the flow rate: (V/min) where VR– 3V. This simple calculation means that that proper reservoir baffling be used. There are a number of
ideally the total volume of the reservoir should turn over at least three (3) possible designs; and one design is shown in Fig. 4 (10). It is
times per minute which is a common recommendation used for mobile recommended that reservoir design be reviewed with the pump
hydraulic units (8). manufacturer before initiating the test program.
NOTE 20—Typically, the reservoir volume in actual hydraulic systems
may vary from as small as 1 to 1.5 times the flow rate for mobile systems 8.2.3 ANSI (NFPA)T3.16.2 provides some useful guide-
up to 2 to 4 times the flow rate for industrial stationary systems. It is lines for the design, construction, and selection of reservoirs.
important that the heat exchanger capacity be sufficient to provide the Also included in this document are descriptions of proper
necessary temperature control of the hydraulic fluid, particularly when function and maintenance of hydraulic reservoirs.
smaller reservoirs are used (see 8.4). 8.3 Inlet Piping Requirements (8)—The suction line into the
8.2.1 Additional recommended reservoir design features reservoir for the hydraulic pump must be adequately sub-
include (9): merged to prevent vortexing. The following rules from the
8.2.1.1 The suction feeds to the hydraulic pump shall be Lightning Reference Handbook (8) have been offered as
FIG. 4 Illustration of a Reservoir Baffling Design that Has Been Recommended
16
D 6813 – 02
guidelines to prevent vortexing: rate, there is significant danger that the pump will cavitate. The
8.3.1 Design intake lines for the minimum possible velocity, fluid flow versus shaft speed for a typical hydraulic pump will
<4 ft/s. be linear up to the point where the fluid can no longer enter the
8.3.2 Ensure that the intake line is submerged 1.75 to 2 pumping chambers of the pump as they are opened and closed
times the intake line inside diameter. because of shaft rotation. When this occurs, the chambers will
8.3.3 Use bell-mouthed fittings on intake pipes to reduce only partially fill and the outlet flow will be reduced. Under
intake velocity at point of entry below the pipe velocity. these conditions, the pump will be starved for fluid. The speed
8.3.4 Ensure that the intake pipe is 5 to 6 times the pipe where this starvation will occur depends on the viscosity and
inside diameter away from the nearest reservoir wall on at least density of the hydraulic fluid as well as the physical configu-
one side. ration of the pump inlet and connecting lines. Therefore, it is
8.3.5 Ensure that the intake pipe is no closer to the reservoir necessary to size the inlet piping and to properly position the
bottom than the pipe (inside diameter/2). pump relative to the reservoir such that the inlet pressure to the
8.4 Hydraulic Oil Temperature—The pump inlet oil tem- pump is positive.
perature should be the maximum allowed by the pump manu- 8.5.1 The pressure at the inlet to the pump is normally called
facturer or equipment manufacturer. The purpose is to test the the Net Positive Suction Head (NPSH) and may be calculated
thermal and oxidative stability of the fluid which affects in terms of absolute pressure (11). The entire system from the
deposit formation, corrosion, and filter plugging. This is fluid level in the reservoir to the inlet of the pump must be
normally approximately 90 to 95°C for anhydrous fluids. taken into account when determining the NPSH as illustrated in
Water-containing fluids must be tested at a lower temperature Fig. 5. The primary factors are:
and the temperature that should be used is that specified for this 8.5.1.1 The atmospheric head or the atmospheric pressure at
class of fluids by the hydraulic pump manufacturer. the particular location (HA).
8.4.1 Both the fluid reservoir temperature (or pump inlet oil 8.5.1.2 The friction head or the pressure needed to over-
temperature) and the case drain oil temperature should be come the losses due to friction when the fluid is flowing
recorded. Typically, the case drain oil temperature is approxi- through the intake pipe, fittings, valves, and area changes (HF).
mately 10 to 20°C higher than the pump inlet temperature. 8.5.1.3 Static inlet head or vertical distance from the cen-
NOTE 21—The recommended fluid viscosity and viscosity limits for the terline of the pump inlet to the free surface level in the
pump being tested should be obtained from the pump manufacturer. reservoir (HS).
Typically, the recommended maximum oil temperature is that value that 8.5.1.4 The vapor pressure of the fluid at the fluid tempera-
provides a fluid viscosity of 8 to 10 cSt. However, testing may be ture (HVP).
conducted at a higher temperature that provides a fluid viscosity of 6 to 7
8.5.2 These parameters can be used to calculate the NPSH
cSt. However, if the fluid viscosity is 6 to 7 cSt, a high-performance
hydraulic oil with an anti-wear additive system is typically required. according to the equation:
NPSH 5 HA 1 HS 2 HF 2 HVP (9)
8.5 Pump Inlet Condition—If the hydraulic fluid cannot be
supplied to the pumping chambers of the pump at a sufficient 8.5.2.1 The vapor pressure (HVP) that must be used in this
FIG. 5 Illustration of NPSH Parameters
17
D 6813 – 02
calculation is the vapor pressure of the fluid at the inlet valves, and so on, and should be monitored during a pump test.
(reservoir) temperature. This can be a substantial negative Particle generation is high at the beginning of the pump test
contribution, particularly for water-containing fluids at el- and usually declines through the test. At the end of the test,
evated temperatures. very low particle concentrations are expected if the system has
8.5.2.2 It is important to maintain a positive inlet pressure. appropriate filtration. The best way to obtain reliable data is by
However, the actual inlet pressure that must be maintained to in-line counting. Off-line bottle sampling is subject to many
prevent cavitation is specific to the piston pump design, and errors.
this value should be obtained with respect to the hydraulic test 9.2.1 Cleanliness requirements are determined by the equip-
circuit from the pump manufacturer. If insufficient inlet pres- ment specifications available from the piston pump supplier.
sure cannot be achieved by repositioning the pump relative to Some recommendations are provided in DIN 51515. It is
the reservoir, then it may be necessary to “supercharge” the important to have a good filtration in the test system to provide
inlet using an auxiliary feed pump. adequate system cleanliness. System cleanliness requirements
8.5.2.3 It is also recommended that the suction feed to the will be determined by reviewing the pump manufacturer
operating circuit be sized to limit the pump intake velocity to recommendations. Generally, the filter rating shall include a
1.2 m/s (4 ft/s) (9). Beta rating of at least 75 to obtain the appropriate ISO particle
NOTE 22—The auxiliary pump must have a net positive suction head at
count rating.
its inlet also. 9.2.2 The hydraulic oil may contain typical concentrations
of water which shall be determined using Karl Fischer analysis
8.6 Intake Line Placement—Ensure that the inlet pipe is 5 to (see 6.3.3). Typically, new, unused mineral-base hydraulic oils
6 times the pipe inside diameter from the nearest obstruction. contain 0.04 to 0.1 % water (100 to 300 ppm is typical for
(An obstruction would include: elbow, joint, or any obstruction anti-wear hydraulic oils which have less than 1 wt % com-
to flow.) The inlet pipe should not be closer to the reservoir pounding).
bottom than the inside diameter of the inlet pipe/2.
8.7 Pump Metallurgy—The metallurgy of the critical mate- 10. Pump Test Monitoring and Evaluation
rial pairs of the pump being used are important and may affect 10.1 Various operational parameters may be monitored
wear performance. Critical material pairs include: wear plate/ throughout the pump test. These parameters are summarized in
shoe interface, port plate/face plate interface, piston/barrel 10.1.1-10.1.6.
sleeve, cylinder block, pistons, shoes, valve plate, rolling 10.1.1 Vibrational Analysis—Sources of system noise and
element bearings, shaft seals, and the like. vibration may be mechanical or fluid-borne.
10.1.2 Mechanical Noise—Sources of mechanical vibra-
9. Fluid Specification Requirements tions include vibrating surfaces from pressure fluctuations
9.1 Importance of Viscosity—Temperature Properties—One emanating from pistons, unbalanced rotational vibrations, or
of the most important fundamental physical properties of a vibrating pipe walls. For example, increased vibration of the
hydraulic fluid is viscosity. Fluid viscosity affects both opera- pump case may indicate wear of the shaft/bearing pair.
tional characteristics of the hydraulic system and the lubrica- 10.1.3 Fluid-Borne Noise—Liquid motion may produce
tion properties of the fluid. pressure fluctuations caused by fluid dynamics. Examples of
9.1.1 Maximum and minimum viscosity limits for hydraulic fluid dynamic sources of noise and vibration include: turbu-
pumps are dependent on pump design and these values are lence, cavitation, flashing of the hydraulic fluid, and flow
obtainable from the manufacturer of the piston pump being separation or vorticity. Pressure and flow pulsations may lead
tested. The maximum fluid viscosity that can be used is known to mechanical vibrations which may radiate acoustic noise.
as “cold start” viscosity. These fluid dynamic sources characteristically lead to unstable
9.1.2 The effect of temperature and pressure on the pump- flow patterns producing vortices at the boundaries between the
ability of a hydraulic fluid must also be considered. There is high-velocity and low-velocity regions. These vortices are
typically an optimal range for proper operation of a hydraulic converted to pressure perturbations as they impinge on side-
pump. For example, at very low temperatures, increased fluid walls which, in turn, result in vibration of the piping or pump
viscosity leads to cavitation, and at excessively high tempera- housing.
tures, insufficient fluid viscosity results in pump slippage and 10.1.4 Pressure Monitoring—Increased magnitude of the
loss of efficiency and also loss of lubrication leading to wear. pressure spikes may indicate wear of the valve plate or erosion.
9.1.3 Although the pump manufacturer will have a recom- Uneven pressure output could reflect wear within the compen-
mended operating fluid viscosity range, there are trade-offs. A sator.
higher fluid viscosity grade will exhibit lower oxidative stabil- 10.1.5 Volumetric Output—A decrease of the flow would
ity, poorer heat transfer, and slower air release, but the lower indicate internal wear or change in fluid viscosity. Monitoring
viscosity grade will stress the anti-wear performance. Both case drainage would be a confirmation of this effect. An
extremes affect cavitation. Therefore, the effects of both increase in case drainage flow and temperature would be
temperature and viscosity of a hydraulic fluid on performance indicative of internal wear.
must be considered. 10.1.6 Pump Operating Parameters—It is recommended
9.2 Contamination Levels—Hard solid particles, especially that a data log be kept of the hydraulic pump test. Table 4
those larger than 10 µ, cause abrasive wear not only in the provides an illustration of such a log. In addition to the data
hydraulic pump but also within the system components such as shown in Table 4, information relating to pump derating shall
18
D 6813 – 02
TABLE 4 Hydraulic Pump Operating Parameters
Required Data, Constant Test Condition Variable Test Condition
Variable Test Condition,
Operation Conditions Measure Before (Flow and Pressure), (Flow and Pressure Profile
h
Start of Test h and Cycles), hA
Speed, rpm
Inlet Pressure, bar
System Pressure, bar
Reservoir Fluid Temperature, °C
Leakage Fluid Temperature, °C
Leakage Flow, L/min (Case Drain)
Leakage Pressure, bar
Shaft Power, kW
Hydraulic Power, kW
Total Efficiency, %
Particle contamination, cleanliness classB
Condition Monitoring (Body Noise)
A
Profile for flow: 1.5 s from min to max and from max to min, 1.5 s constant min and max flow, 1.5 s from max to min flow, (6 s/cycle, 600 cycles/h), pressure followed
in the same way.
B
Cleanliness class 19/16/13 (ISO 4406) is recommended as a minimum.
be recorded. Also, note the field history of the hydraulic fluid, important to determine the water content not only on the fresh fluid but
which shall include a brief description of years of experience also on the fluid at the conclusion of the test and at intermediate times, if
and any known strengths and deficiencies. needed. It is suggested that water content should be maintained at 61 %
of the initial value.
11. Pump Test Monitoring and Evaluation Criteria 11.1.2 There are three manufacturers of analytical ferrogra-
11.1 Fluid Test Parameters—Key fluid characterization phy equipment plus numerous in-house methods using filter-
properties should be measured at the start and end of a test, and gram techniques (sometimes called patch ferrography). The
some should be monitored at intervals during the test. An debris field is analyzed microscopically using an assortment of
example protocol is given in Table 5. particle treatment methods (heat, chemicals, impaction, bichro-
11.1.1 As a minimum, the fluid test parameters should matic light, magnetism, and the like). Some laboratories use
include: viscosity (Test Method D 445), neutralization number image analyzers and particle recognition software. While there
(Test Method D 664), water content (Test Method D 1144 or are no current ASTM or ISO methods for the optical analysis
E 203), and reserve alkalinity (Test Method D 1121), if the of wear particles, a standard condition monitoring test proce-
fluid is a water-containing fluid such as HFB or HFC. Particle dure, which includes wear particle identification methods, is
count analysis (ISO 11171) should be performed on the used being developed by ISO TC108/SC5/WG4.
fluid and, if necessary, ferrographic analysis or elemental 11.1.3 An example of a performance criterion is that a fluid
analysis, or both, to determine the source of any particles (wear fails if there is a change in viscosity of >20 % or if an increase
or corrosion). Elemental analysis may also be done to monitor in neutralization number of $2 mg KOH/g has occurred. Other
additive element depletion or wear metal accumulation. Analy- parameters such as filterability, color, appearance, foaming
sis of metals is typically performed by Test Methods D 5185 or tendency, air release time, and loss of oxidation inhibitor may
D 6595. A procedure similar to Test Method D 6376 may be be monitored.
used for analyzing wear particles on a patch with subsequent 11.2 Pump Performance Appraisal—Variation of the pump
elemental analysis using X-ray fluorescence spectroscopy. operating parameters such as input speed, system pressure,
NOTE 23—The performance of water-containing fluids such as HFB system temperature, case temperature, case pressure, and flow,
and HFC fluids is dependent on the actual water content. Therefore, it is throughout the test is an excellent indicator of wear. A sudden
increase in temperature and a sudden drop in flow are good
TABLE 5 Measuring Fluid Properties During a Pump Test indicators that there are lubricating problems with one or more
Test Start of End of
bearing surfaces. In some pumps, a significant loss of flow
Property Monitor (>10 %) over a longer period (perhaps 225 h) may indicate
Method Test Test
Viscosity at 40°C D 455 X X X yellow metal corrosion. An increase in pressure drop across the
Viscosity at 100°C X X downstream filter may indicate plugging due to particles from
Total Acid Number D 664 X X X wear or fluid deterioration.
Water Content D 1744, D 6304 or D 95 X X X
Appearance Visual X X X 11.2.1 It is recommended that the condition of internal wear
Color D 1500 X X contacts shall be determined and recorded. Table 6 provides a
Infrared Spectrum X X X
Particle Count ISO 4406 X X X
partial list for illustrative purposes. Each component should be
Metals D 5185 X X X photographed to provide a record of these observations. In the
Demulsibility D 1401 X X case of bearings and other parts, it may be desirable to
Foaming D 892 X X
Air Release D 3427 X X
determine weight loss during the test. If the pump manufac-
Oxidation D 2272 X X turer can provide a wear catalog, comparing the appearance of
Filterability NF E48– 690 X X X parts to examples in the catalog can aid in determining wear.
NF E48–691 X X
NF E48–692 X X X 11.2.2 At the end of the test, the pump should be disas-
sembled and examined both qualitatively and quantitatively for
19
D 6813 – 02
TABLE 6 Pump Component Wear Rating pressure test conditions summarized in Table 7 and shown
Part Ratings
Photograph and Description of the Type schematically in Fig. 6. The test evaluation criteria are pump
and Degree of Wear Observed efficiency change, wear and surface roughness, formation of
Piston Shoe Face Land darkening, discoloration, material deformation, lacquer and varnish, and hydraulic oil deterioration.
scratches, scoring, plastic flow
Swash (Creep) Plate Scratches, polishing, discoloration, metal transfer,
13.3 Rexroth Piston Pump Test—Rexroth has proposed a
heat checks three-stage piston pump test based on the Brueninghaus
Port (Face) Plate Darkening, abrasive wear, cavitation, cracking, A4VSO 125 piston pump (13). Stage one is conducted at
heat checks
maximum operating pressure, displacement, and temperature
and at the minimum viscosity specified for the fluid being
tested. The test duration is 250 h at which time the pump is
wear and parts distress. Examples are polishing or scuffing of, dismantled and inspected. The second stage of the test is a
or metal transfer to, the swash plate; piston shoe land wear; pulsed pressure test at the maximum displacement of the pump.
port plate and face plate corrosion or cavitation wear; darken- This stage is operated for one million cycles. When this stage
ing or deposits in cylinder bores; radial lip seal wear; and is complete, the pump is dismantled and inspected. The third
bearing distress. stage is a variable displacement stage at maximum pressure,
11.2.3 An example of wear determination would be visual maximum temperature, and minimum fluid viscosity. The test
inspection with photography of the degree of smearing that duration is one million cycles (at approximately 2 Hz) at which
may occur on the valve plate and cylinder block at the time the pump is dismantled and inspected again. These test
conclusion of the test. A “pass/fail” determination would be conditions are summarized in Table 8. The final pass/fail
made by comparing the degree of smearing with a wear catalog assessment is made with reference to a standard damage
provided by the pump manufacturer for the wear surface being catalog provided by Rexroth.
examined. The wear catalog would indicate no wear, accept- 13.4 Sundstrand Water Stability Test Procedure—This test
able and unacceptable levels of wear upon which the final was originally conducted using a Sundstrand Series 22 piston
determination is made. Any abnormal wear, scuffing, or adhe- pump at a constant pressure (14). Currently this test procedure
sive failure is a cause for concern. Other wear surfaces to is conducted using a Sundstrand Series 90 piston pump with a
examine include: shaft bearings, piston block/bore interface, 55 cm3 displacement (15). The objective of the test is to
piston/slipper interface, slipper/swash-plate interface, cylinder determine the effect of water contamination (1 %) on mineral
block/valve plate interface, shaft seal, and other sealing areas. oil hydraulic performance and yellow metal corrosion. How-
11.3 Surface Analysis—Using visual inspection as the sole ever, other fluids, including water-containing fluids such as
means of evaluating surface condition is often insufficient. HFB and HFC fluids, may also be evaluated using this test. The
After testing, surface wear should be analyzed using accurate test conditions are summarized in Table 9. The test duration is
surface measurement. This may be done using a stylus or laser 225 h at which time it is disassembled and inspected for wear,
equipped instrument. Reasonable limits of maximum wear corrosion and cavitation. If the flow degradation is equal to or
depth in relation to the measured mean particle concentration greater than 10 %, the test is considered to fail.
should be established as a pass/fail guideline. 13.5 Eaton PVH57C Piston Pump Test Procedure (16)—
This test procedure is used to evaluate hydraulic fluids for use
12. Reference Oil
in axial piston pumps. The pump used for this test is the Eaton
12.1 The reference oil selected is dependent on the problem PVH57 piston pump equipped with a pressure compensator
to be solved. For example, one may select a hydraulic fluid with load sensing control. It consists of an actual test duration
composition to improve upon its performance level. Alterna- time of 250 h, not including break-in or performance running.
tively, one may select an oil with minimum acceptable perfor- The operation temperature is dependant on the capability of the
mance. test fluid at the specified temperature, whichever is lower. For
anti-wear petroleum oils, the required running conditions are
13. Illustrative Pump Manufacturers Piston Pump Tests speed—2400 rpm, pressure—250 bar (3625 psi),
13.1 There are numerous piston pump test procedures to temperature—93°C, and rated inlet pressure—atmospheric
assess the lubricating properties of a hydraulic fluid. Most of pressure. Hydraulic pumps are typically derated for use with
these tests have been developed and used by various pump non-petroleum oil-based fluids. The Eaton PVH57 hydraulic
manufacturers. However, at the present time there is no piston pump is also derated for use with non-petroleum
national standard piston pump test. This section provides an oil-based hydraulic fluids and the recommended test conditions
overview of a number of piston pump tests that have been for non-petroleum-based fluids are summarized in Table 10.
developed by equipment manufacturers to evaluate certain
features of their pumps. These tests apply many of the ideas
TABLE 7 Summary of Komatsu HP35V35 and 35 Piston Pump
discussed in Sections 7, 8, 10, and 11. These tests are generally Test Conditions
performed as fluid qualification tests for pumps manufactured
Pressure 10 to 420 kg/cm2(140 to 6000 psi)
by the specific pump producer. Oil Flow 16 gal (at 140 psi); 5 gal at (6000 psi)
13.2 Komatsu HPV35+35 Piston Pump Test—Recently, Speed 2100 rpm
Komatsu developed a piston pump test to evaluate biodegrad- Temperature 80°C
Tank Volume 16 gal
able vegetable oil-based hydraulic fluids (12). This test is based Duration 500 h
on a Komatsu HPV35+35 dual-piston pump using cycled
20
D 6813 – 02
FIG. 6 Schematic Illustration of the Test Sequence Used for the Komatsu HP35V35 + 35 Piston Pump Test
TABLE 8 Summary of the Rexroth Brueninghaus A4VSO 125 TABLE 10 Eaton PVH57 Specification Fluid Testing Conditions
Piston Pump Test Conditions Rated
Rated Speed, Rated Pressure,
Stage 1—Continuous Load Operation Fluid Temperature,
rpm max, bar/psig
Running Conditions Maximum operating pressure, maximum fluid °C/°F
temperature, minimum fluid viscosity
Water Glycol (HFC) 1800 170/2465 50/122
specified for fluid class
Invert Emulsion (HFB) 1500 155/2247 50/122
Total Time/Stage 1 250 h; pump is dismantled and inspected
90-10 HWBF Thickened (HFAS) 1500 155/2247 50/122
Phosphate Ester (HFDR) 1800 230/3335 65/149
Stage 2—Pulsed Pressure Operation at Maximum Displacement
Polyol Ester (HFDU) 1800 230/3335 65/149
Running Conditions Load pressure—0-maximum, maximum fluid
Environmentally Friendly– 1800 250/3625 65/149
Vegetable Base–(HETG)
specified for fluid class
Environmentally Friendly– 2400 250/3625 65/203
Total Time/Stage 2 1 million cycles, 2 to 3 Hz, 100 to 150 h;
Synthetic Base–(HEES)
pump is dismantled and inspected
Anti-wear Petroleum Oil 2400 250/3625 93/199
Stage 3—Variable Displacement at Maximum Pressure
Running Conditions Maximum pressure, maximum fluid non-petroleum-based hydraulic fluids.
specified for fluid class 13.5.1 The Eaton PVH57C piston pump test is conducted
Total Time/Stage 3 1 million cycles, 1 s/cycle, total time is 280 h using the recommended speed, pressure, and temperature
at which point the pump is dismantled
and inspected provided in Table 10 while monitoring input torque, output
pressure, output flow, case flow, case temperature, case pres-
sure, inlet temperature, and SAE Derived Capacity (according
TABLE 9 Summary of the Sundstrand Piston Pump Water to SAE J745) throughout the following procedure:
Stability Test Procedure 13.5.1.1 Run a “performance” test as summarized in Table
Input Speed 3000 to 3200 rpm 11.
Load Pressure 5000 psi (344 bar) 13.5.1.2 Run for 50 h at the rated pressure, speed, and
Charge Pressure 180 to 220 psi (12.4 to 15.2 bar)
Case Pressure 40 psi (2.8 bar) max temperature. Spot check performance at 2400 rpm, 120°F
Stroke 1⁄2 of full
(49°C) flooded inlet, and rated pressure—20 bar.
Reservoir Temperature 150 6 10°F ( 65 6 4°C)
Loop Temperature 180 6 10°F ( 82 6 4°C)
13.5.1.3 Disassemble pump and visually inspect to deter-
Maximum Inlet Vacuum 5 in. Hg mine pass/fail (see 13.5.2 for pass/fail criteria). Reassemble the
pump.
TABLE 11 Summary of the Eaton PVH57C Piston Pump
The rated inlet pressure for non-petroleum-based hydraulic “Performance” Test Procedure
fluids is also equal to atmospheric pressure. Conditions See Table 10
NOTE 24—The recommended derated test conditions shown in Table 10 Pressure (bar) A
70, 140, (210 ), Rated Pressure—20, Rated Pressure
for the Eaton PVH57 hydraulic piston pump do not necessarily apply to Speed (rpm) 1200, (1800A), Rated Speed
other Eaton hydraulic pumps nor do they necessarily apply to hydraulic Temperature Rated temperature or fluid manufacturers temperature
pumps available from other manufacturers. The data in Table 10 is offered (whichever is lower)
A
as an illustration of hydraulic pump derating that may be encountered for These are the conditions that are permissible for use with a petroleum oil.
21
D 6813 – 02
13.5.1.4 Spot check performance at 2400 rpm, 120°F 13.5.2.4 Yoke bearing journals—finish and visual inspec-
(49°C), flooded inlet, and rated pressure—20 bar. Then run the tion.
following cycling test for 200 h: 13.5.2.5 Saddle bearings—finish and visual inspection.
(1) 0.75 s full flow at 90 % rated pressure; 13.5.2.6 Identify pistons for reassembly into same bore and
(2) 0.5 s at rated pressure; and measure piston/shoe endplay and piston diameter at top,
(3) 0.5 s at low pressure standby. middle and bottom.
13.5.1.5 Disassemble pump after approximately 48 h of 13.5.2.7 All piston bores measured at top, middle and
cyclic endurance. If hardware is visually acceptable, then bottom.
reassemble pump, spot check performance and continue the 13.5.2.8 Measure metering land diameters and width on
cyclic test as described in 13.5.1.4. both control spools
13.5.1.6 Run the performance test as summarized in Table 13.5.2.9 Photograph visually worn parts.
11. 13.5.3 After these measurements are taken, the pass/fail
13.5.1.7 Disassemble and inspect. The pass/fail criteria are criteria are:
provided in 13.5.2. 13.5.3.1 Visual fail if there is material transfer or a coarser
13.5.2 Summary of Pass/Fail Criteria for the Eaton surface finish, or both, is observed resulting from abnormal
PVH57C Piston Pump after Testing—The Eaton PVH57C wear.
piston pump will be disassembled at the indicated times during 13.5.3.2 Shoe endplay acceptance criterion is a change of
the test and inspected for: less than 0.05 mm.
13.5.2.1 Valve plate running face—finish and visual inspec- 13.5.3.3 Overall maximum efficiency loss of 3 %.
tion. 13.5.3.4 Maximum variation in full flow of 2 %.
13.5.2.2 Cylinder block running face—finish and visual
inspection. 14. Keywords
13.5.2.3 Yoke running face—finish and visual inspection. 14.1 hydraulic fluid; hydraulic pump testing; piston pump
REFERENCES
(1) Lemberger, S., and Totten, G. E., “Chapter 12—Failure Analysis,” 0239-B1, Parker Hannafin Corporation, Motion & Control Group,
Handbook of Hydraulic Fluid Technology, Ed. G. E. Totten, Marcel Training Dept., Cleveland, OH, 1993, p. 13-1.
Dekker Inc., New York, NY, 2000, pp. 601-673. (11) Tessmann, R. K., Melief, H. M., and Bishop, R. J., “Chapter 1—Basic
(2) Fire Resistance of Industrial Fluids, STP 1284, Eds. G. E. Totten and Hydraulic Pump and Circuit Design,” Handbook of Hydraulic Fluid
J. Reichel, ASTM International, W. Conshohocken, PA, 1996. Technology, Ed. G. E. Totten, Marcel Dekker Inc., New York, NY,
(3) CFR—Part 35, “Fire Resistant Fluids,” U.S. Mine Safety and Health 2000, pp. 1-64.
Administration. (12) Ohkawa, S., Konishi, A., Hatano, H., Ishihama, K., Tanaka, K., and
(4) “Approval Standard: Less Hazardous Hydraulic Fluid—Class Number Iwamura, M., “Oxidation and Corrosion Characteristics of Vegetable-
6930,” Factory Mutual Research Corporation, Norwood, MA, Feb. 7, Base Biodegradable Hydraulic Oil,” SAE Technical Paper Series,
1975. Paper Number 951038, 1995.
(5) Johnson, H. T., and Lewis, T. I., “Vickers 35VQ25 Pump Test,” (13) Melief, H. M., Totten, G. E., and Bishop, R. J., “Overview of the
Tribology of Hydraulic Pump Testing, ASTM STP 1310, Eds. G. E. Proposed Rexroth High-Pressure Piston Pump Testing Procedure for
Totten, G. H. Kling, and D. J. Smolenski, ASTM International, W. Hydraulic Fluid Qualification,” SAE Technical Paper Series, Paper
Conshohocken, PA, 1996, pp. 129-139. Number 982022, 1998.
(6) “Pump Testing Performance for Evaluation of Antiwear Fluids for
(14) “Sundstrand Water Stability Test Procedure,” Sundstrand Bulletin
Mobile Applications,” Vickers Form No. M-2952-S, Eaton Corpora-
No. 9658, Sauer-Danfoss Corp., Ames, IA.
tion, Eaton Hydraulics, Eden Prairie, MN.
(7) Bishop, R. J., and Totten, G. E., “Managing Foam and Aeration in (15) “The Effect of Water-Contaminated Hydraulic Fluid on the Sauer-
Hydraulic Fluids,” Proceedings of the International Conference and Sundstrand 90 Series Axial Piston Pump,” Specification Number JDQ
Exhibition, Practicing Oil Analysis 2000, Tulsa, OK, October 24-26, 84, John Deere Corporation, Waterloo, IA.
2000, pp. 58-70. (16) Eaton Engineering Standard ATS-362, “Eaton PVH57C—Test Pro-
(8) Fluid Power Designer’s Lightningt Reference Handbook, 8th Edition, cedure for Evaluation of Fluids for Open Loop Axial Piston Pumps,”
Paul-Munroe Rucker, Inc., Whittier, CA, 1994, p. 118. Eaton Corporation, Hydraulics Division, Eden Prairie, MN.
(9) Fluid Power Designer’s Lightningt Reference Handbook, 8th Edition, (17) McHugh, P., Stofey, W. D., and Totten, G. E., “Chapter 14—Mineral
Paul-Munroe Rucker, Inc., Whittier, CA, 1994, p. 17. Oil Hydraulic Fluids,” Handbook of Hydraulic Fluid Technology, Ed.
(10) “Lesson 13—Hydraulic Fluid Conditioning,” Fluid Power G. E. Totten, Marcel Dekker Inc., New York, NY, 2000, pp. 711-794.
Basics—An Introduction to Hydraulics and Pneumatics, Bulletin
22
D 6813 – 02
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website
(www.astm.org).
23

D 6813 - 02 - Rdy4mtmtmdi

Uploaded by

Copyright:

Available Formats

D 6813 - 02 - Rdy4mtmtmdi

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

D 6813 - 02 - Rdy4mtmtmdi

Uploaded by

Copyright:

Available Formats

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.

Contact ASTM International (www.astm.org) for the latest information.

An American National Standard

Standard Guide for

1. Scope Bituminous Materials by Distillation2

FIG. 1 Illustration of an Axial Piston Pump

3.1.12 fixed displacement—the amount of flow cannot be

TABLE 1 Hydraulic Fluid Physical Property Characterization Tests

Hydraulic Fluid Classification

Kinematic viscosity at 40°C X X X X X X X X X X X X ASTM D 445

Thermal conductivity X X X X X X X X X X X X ASTM D 2717

FIG. 4 Illustration of a Reservoir Baffling Design that Has Been Recommended

FIG. 5 Illustration of NPSH Parameters

You might also like