Scribd Logo
Upload

Welcome to Scribd!

  • 39 views

    Quick Start Guide: PRTXXLT

    Uploaded by

    GombosTamás

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Quick Start Guide: PRTXXLT

    Uploaded by

    GombosTamás
    39 views2 pages

    Original Title

    QSG-PRTxxLT-EN

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    39 views2 pages

    Quick Start Guide: PRTXXLT

    Uploaded by

    GombosTamás

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    QUICK START GUIDE

    PRTxxLT (firmware version x.34.xxx or newer)

    Configuration of PRTxxLT series reader as RACS terminal with ID1 address

    ! In case of reader without keypad prepare EM 125 kHz standard card with any number to be used in further programming.

    1. Procedure for programming the reader as RACS terminal with ID1 address (code 001)
    1.1. Remove all connections from CLK, IN1 and RTS lines.
    1.2. Connect CLK (green wire) with IN1 (yellow wire).
    1.3. Restart the reader (switch power supply off and on).
    1.4. When LED OPEN (green) blinks, disconnect CLK and IN1 lines.
    1.5. When LED SYSTEM (orange) blinks enter three digits corresponding to the code of required operating mode. Each digit corresponds
    to the number of card readings:
    • read the card 10 times and wait for double beep or press 0 (the first digit),
    • read the card 10 times and wait for double beep or press 0 (the second digit),
    • read the card 1 time and wait for double beep or press 1 (the third digit).
    1.6. Procedure is finished and the reader restarts automatically with new settings.

    Configuration of PRTxxLT series reader as Wiegand 26 bit terminal*

    ! In case of reader without keypad prepare EM125kHz standard card with any number to be used in further programming.

    1. Procedure for programming the reader as Wiegand 26 bit terminal (code 100)
    1.1. Remove all connections from CLK, IN1 and RTS lines.
    1.2. Connect CLK (green wire) with IN1 (yellow wire).
    1.3. Restart the reader (switch power supply off and on).
    1.4. When LED OPEN (green) blinks, disconnect CLK and IN1 lines.
    1.5. When LED SYSTEM (orange) blinks enter three digits corresponding to the code of required operating mode. Each digit corresponds
    to the number of card readings:
    • read the card 1 time and wait for double beep or press 1 (the first digit),
    • read the card 10 times and wait for double beep or press 0 (the second digit),
    • read the card 10 times and wait for double beep or press 0 (the third digit)**.

    PIN codes from 1 to 10 digit transmitted as BCD code.


    *

    Each digit corresponds to the number of card readings i.e. 0 digit corresponds to 10 card readings, 1 digit corresponds to 1 card reading, 9 digit corresponds to 9 card readings etc.
    **

    Technical support is available in weekdays:


    • from 8:00 am to 4:00 pm at PSTN number +48 55 267 01 26
    • from 4:00 pm to 8:00 pm at GSM number +48 664 294 087
    !
    If no actions are performed within 9 sec. then the reader shall automatically finish configuration procedure with following
    settings for input lines: IN1 enables control of LED SYSTEM and IN1 enables control of LED OPEN. Detailed description of possible
    input functions is available in the reader manual.

    1.6. Procedure is finished and the reader restarts automatically with new settings.

    PRTXXLT SERIES READER WIRES:


    Green CLK
    Brown DTA
    Yellow IN1
    Pink IN2
    Red +12V
    Blue GND
    Gray TAMPER
    White TAMPER

    Legal Notice

    This document is not intended to be a technical specification of the product and has informative character only. The Manufactures of product reserves right
    to change its characteristic without notice. The product features listed in this document refer to the entire series and depends on particular product version,
    configuration and additional equipment.

    © 2016 ROGER sp. z o.o. sp. k. All rights reserved. This document is a subject to the Terms of Use in their current version published at the www.roger.pl

    ROGER sp. z o.o. sp. k. T. +48 55 272 0132


    Gościszewo 59 F. +48 55 272 0133
    82-400 Sztum E. [email protected]
    Poland I. www.roger.pl

    You might also like